NAPOLEON NLF50H Manuel utilisateur

Catégorie
Cheminées
Taper
Manuel utilisateur
EN
W415-1223 / B / 10.11.18
FR
PG
21
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
NEVER LEAVE CHILDREN OR OTHER AT RISK INDIVIDUALS ALONE WITH THE APPLIANCE.
INSTALLATION AND
OPERATING INSTRUCTIONS
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada /
103 Miller Drive, Crittenden, Kentucky, USA, 41030
Phone (705)721-1212 • Fax (705)722-6031 • www.napoleon replaces.com [email protected]
SAFETY INFORMATION
!
WARNING
If the information in these instructions
are not followed exactly, a re may result
causing property damage, personal injury
or loss of life.
- Do not store or use gasoline or other ammable
vapors and liquids in the vicinity of this or any
other appliance.
$10.00
CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA C22.2 No-46 / UL 1278
Napoleon 50"
ELECTRIC FIREPLACE
EN
W415-1223 / B / 10.11.18
2
NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.
TABLE OF CONTENTS
1.0 INTRODUCTION 3
1.1 DIMENSIONS 4
1.2 LISTING APPROVALS 4
1.3 GENERAL INSTRUCTIONS 5
1.4 UNPACKING AND TESTING APPLIANCE 5
2.0 LOCATING APPLIANCE 6
2.1 GROUNDING APPLIANCE 6
3.0 INSTALLATION 7
3.1 MINIMUM CLEARANCE TO COMBUSTIBLES 7
3.2 MINIMUM MANTEL CLEARANCES 7
3.3 INSTALLING THE APPLIANCE 8
3.4 RECESSING INSTALLATION 9
3.4.1 MINIMUM CLEARANCE TO COMBUSTIBLES 9
3.4.2 FRAMING 9
3.4.3 MOUNTING BRACKET INSTALLATION 10
3.5 HARD WIRING INSTALLATION 11
4.0 FINISHING 12
4.1 GLASS DOOR REMOVAL 12
5.0 OPERATING INSTRUCTIONS 13
5.1 MAIN POWER SWITCH 13
5.2 OPERATING BY REMOTE CONTROL 13
6.0 MAINTENANCE 14
6.1 FUSE REPLACEMENT 14
7.0 WIRING DIAGRAM 15
8.0 REPLACEMENT PARTS 16
9.0 TROUBLESHOOTING 17
10.0 WARRANTY 18
11.0 SERVICE HISTORY 19
EN
W415-1223 / B / 10.11.18
3
1.0 INTRODUCTION
!
WARNING
THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF
CONTACTED.
Do not operate appliance before reading and understanding operating instructions. Failure to operate
appliance according to operating instructions could cause re or injury.
Risk of burns. Power to the appliance should be turned off and the appliance allowed to cool before
servicing. To disconnect power to the appliance, turn controls to off, then remove plug from outlet.
Do not install damaged, incomplete or substitute components.
Do not burn wood or other materials in this appliance.
Young children should be carefully supervised when they are in the same room as the appliance.
Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier
is recommended if there are at risk individuals in the house. To restrict access to an appliance or stove,
install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the
room and away from hot surfaces.
Clothing or other ammable material should not be placed on or near the appliance.
Due to high temperatures, the appliance should be located out of traf c and away from furniture and
draperies.
Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot
surfaces.
Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.
Check with your local hearth specialty dealer for safety screens and hearth guards to protect children
from hot surfaces. These screens and guards must be fastened to the oor.
Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.
It is imperative that the control compartments, circulating blower and its passageway in the appliance
and are kept clean. The appliance should be inspected before use and at least annually by a quali ed
service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding
material, etc. The appliance area must be kept clear and free from combustible materials, gasoline and
other ammable vapors and liquids.
Under no circumstances should this appliance be modi ed.
Do not use this appliance if any part has been under water. Immediately call a quali ed service technician
to inspect the appliance and to replace any part of the control system which has been under water.
Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the
glass should be done by a licensed or quali ed service person.
Do not strike or slam shut the appliance glass door.
Keep the packaging material out of reach of children and dispose of the material in a safe manner. As
with all plastic bags, these are not toys and should be kept away from children and infants.
Servicing should be done only while the appliance is disconnected from the power supply circuit.
Always unplug appliance when not in use.
Do not operate this appliance with a damaged cord or plug after the appliance malfunctions, has been
dropped or damaged in any manner. Return appliance to authorized service facility for examination,
electrical or mechanical adjustment, or repair.
Do not use outdoors.
Never locate appliance where it may fall into a bathtub or other water container.
Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange cord
away from traf c area and where it will not be tripped over.
Connect to properly grounded outlets only.
Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an
electric shock or re, or damage the appliance.
To prevent a possible re, do not block air intakes or exhaust in any manner. Do not use on soft
surfaces, like a carpet, where openings may become blocked.
Always plug appliances directly into a wall outlet/receptacle. Never use an extension cord or
relocatable power tap (outlet/power strip).
Ensure clearances to combustibles are maintained when building a mantel or shelves above the
appliance. Elevated temperatures on the wall or in the air above the appliance can cause melting,
discolouration or damage to decorations, a T.V. or other electronic components.
EN
W415-1223 / B / 10.11.18
4
1.1 DIMENSIONS
1.2 LISTING APPROVALS
This appliance has been tested in accordance with the CSA Standards for xed and location-dedicated electric
room appliances in the United States and Canada. If you need assistance during installation, please contact
your local dealer.
NOTE: This appliance must be electrically wired
and grounded in accordance with local codes
or, in the absence of local codes, with National
Electric Code ANSI/NFPA 70-latest edition in the
United States or the Canadian Electric Code,
CSA C22.1 in Canada.
Model Number EFL50H NLF50H
Description Wall-Mount
Appliance
Wall-Mount
Appliance
Voltage 120V AC 120V AC
Watts Max 1500W Max 1500W
Amps 15 AMP Grounded
Circuit
15 AMP Grounded
Circuit
Appliance Width 49 7/8" (1266mm) 49 7/8" (1266mm)
Appliance Height 19 7/8" (505mm) 19 7/8" (505mm)
Appliance Depth 4 7/8" (124mm) 4 7/8" (124mm)
Net Weight 56 lbs (25kg) 56 lbs (25kg)
Gross Weight 77 lbs (35kg) 77 lbs (35kg)
FRONT VIEW
TOP VIEW
SIDE VIEW
43 1/2" [1105mm]
49 7/8" [1266mm]
19 7/8"
[505mm]
17 1/8"
[435mm]
4 7/8"
[124mm]
POWER
SWITCH
EN
W415-1223 / B / 10.11.18
5
1.3 GENERAL INSTRUCTIONS
A. Prior to plugging your appliance into an electrical outlet, verify that the house circuit breakers for the
outlet are on.
B. The appliance may emit a slight, harmless odour when rst used. This odour is normal and it is caused
by the initial heating of internal appliance elements and will not occur again.
C. If your appliance does not emit heat, consult the operation section of this manual for further
information.
D. Use with a CSA or UL certi ed surge protector.
E. Do not route the power cord directly underneath the appliance.
This electric appliance meets the construction and safety standards of H.U.D. for application in manufactured
homes when installed according to these instructions.
!
WARNING
READ THESE INSTRUCTIONS COMPLETELY BEFORE BEGINNING INSTALLATION. FAILURE TO
FOLLOW THEM COULD CAUSE AN APPLIANCE MALFUNCTION RESULTING IN SERIOUS INJURY
AND/OR PROPERTY DAMAGE.
ALL ELECTRIC APPLIANCES HAVE HOT AND ARCING OR SPARKING PARTS INSIDE. DO NOT USE
IT IN AREAS WHERE GASOLINE, PAINT OR FLAMMABLE LIQUIDS ARE PRESENT.
THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE OPTIONAL
ACCESSORIES LISTED IN THESE INSTRUCTIONS. USE OF OPTIONAL ACCESSORIES NOT
SPECIFICALLY TESTED FOR THIS ELECTRIC APPLIANCE COULD VOID THE WARRANTY AND/OR
RESULT IN A SAFETY HAZARD.
DO NOT OPEN. RISK OF ELECTRIC SHOCK. NO USER-SERVICEABLE PARTS INSIDE.
DO NOT USE DAMAGED ELECTRICAL CORDS.
SERVICING SHOULD BE DONE ONLY WHILE THE APPLIANCE IS DISCONNECTED FROM THE
POWER SUPPLY CIRCUIT.
TO PREVENT ELECTRIC SHOCK MATCH THE WIDE BLADE OF PLUG TO WIDE SLOT OF
RECEPTACLE AND FULLY INSERT.
As with most electronic devices, your new electric replace has been designed to operate at
temperatures between 5°C (41°F) and 35° C (95°F). During the colder winter months, allow the replace
to reach room temperature before turning it on.
1.4 UNPACKING AND TESTING APPLIANCE
Carefully remove the appliance from the box. Prior to installing the appliance, test to make sure the appliance
operates properly by plugging the power supply cord into a conveniently located 120 Volt grounded outlet.
EN
W415-1223 / B / 10.11.18
6
!
WARNING
2.0 LOCATING APPLIANCE
2.1 GROUNDING APPLIANCE
DUE TO HIGH TEMPERATURES, THIS ELECTRIC APPLIANCE SHOULD BE LOCATED OUT OF
TRAFFIC. KEEP COMBUSTIBLE MATERIALS SUCH AS FURNITURE, PILLOWS, BEDDING, PAPERS,
CLOTHES AND CURTAINS AT LEAST 36" FROM THE FRONT OF THE APPLIANCE.
NEVER LOCATE THIS ELECTRIC APPLIANCE WHERE IT MAY FALL INTO A BATHTUB OR OTHER
WATER CONTAINER.
WEAR SAFETY GLOVES AND SAFETY GLASSES FOR PROTECTION DURING INSTALLATION AND
MAINTENANCE.
TO PREVENT CONTACT WITH SAGGING OR LOOSE INSULATION, THE ELECTRIC APPLIANCE
MUST NOT BE INSTALLED AGAINST VAPOR BARRIER OR EXPOSED INSULATION. LOCALIZED
OVERHEATING COULD OCCUR AND A FIRE COULD RESULT.
DO NOT EXPOSE THE ELECTRIC APPLIANCE TO THE ELEMENTS (SUCH AS RAIN, ETC.)
GROUNDING METHODS
METAL SCREW
(A)
NOT ALLOWED IN CANADA
GROUNDING
MEANS
ADAPTER
GROUNDING PIN
COVER OF
GROUNDED
OUTLET BOX
(C)
(B)
This appliance is for use on 120 Volts. The cord has a plug
as shown in (A). An adapter as shown in (C) is available
for connecting three-blade grounding type plugs to two-slot
receptacles. The green grounding lug extending from the
adapter must be connected to a permanent ground such as
a properly grounded outlet box. The adapter should not be
used if a three-slot grounded receptacle is available.
To disconnect appliance, turn controls to off, then remove
plug from outlet.
EN
W415-1223 / B / 10.11.18
7
3.0 INSTALLATION
Your EFL50H/NLF50H is a wall-mounted appliance. Select a suitable location that is not susceptible to
moisture and is away from drapes, furniture and high traf c areas.
NOTE: Follow all National and local electrical codes.
!
WARNING
RISK OF FIRE! THE POWER CORD MUST NOT BE PINCHED AGAINST A SHARP EDGE. SECURE CORD TO AVOID
TRIPPING OR SNAGGING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY. DO NOT RUN
CORD UNDER CARPETING. DO NOT COVER CORD WITH THROW RUGS, RUNNERS OR THE LIKE. ARRANGE CORD
AWAY FROM TRAFFIC AREAS AND WHERE IT WILL NOT BE TRIPPED OVER.
RISK OF FIRE! TO PREVENT A POSSIBLE FIRE, DO NOT BLOCK AIR INTAKE OR EXHAUST IN ANY MANNER. DO NOT
USE ON SOFT SURFACES WHERE OPENINGS MAY BECOME BLOCKED.
RISK OF FIRE! DO NOT BLOW OR PLACE INSULATION AGAINST THE APPLIANCE.
THIS ELECTRIC APPLIANCE IS TESTED AND LISTED FOR USE ONLY WITH THE APPROVED OPTIONAL ACCESSORIES.
USE OF OPTIONAL ACCESSORIES NOT SPECIFICALLY TESTED FOR THIS ELECTRIC APPLIANCE COULD VOID THE
WARRANTY AND/OR RESULT IN A SAFETY HAZARD.
IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT
CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. DO NOT STORE OR USE GASOLINE OR OTHER
FLAMMABLE VAPORS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.
THIS APPLIANCE IS HEAVY. IT IS HIGHLY RECOMMENDED THAT TWO PEOPLE INSTALL THIS APPLIANCE.
HEATER VENTS ON THE ELECTRIC APPLIANCE CANNOT, IN ANY WAY, BE COVERED AS IT MAY CREATE A FIRE
HAZARD.
DO NOT RUN THE POWER CORD HORIZONTALLY, DIRECTLY BELOW THE APPLIANCE.
3.1 MINIMUM CLEARANCE TO COMBUSTIBLES
Measurements are taken from the glass front.
Bottom 0" Top 8" (203mm) to mantel
Sides 0" Top 8" (203mm) to ceiling
Back 0"
SIDE VIEW
8”(203.2mm)
MANTEL
FLOOR
WALL
!
WARNING
WHEN USING PAINT OR LACQUER TO FINISH THE MANTEL, THE PAINT OR LACQUER MUST BE
HEAT RESISTANT TO PREVENT DISCOLOURATION.
3.2 MINIMUM MANTEL CLEARANCES
NOTE: The power switch is located on the lower right hand side of the appliance. Always ensure that
access to this switch remains accessible.
EN
W415-1223 / B / 10.11.18
8
Due to the many different materials used on different walls, it is highly recommended that you consult your
local builder before you install this appliance on the wall.
A. Select a location that is not prone to moisture and is located at least
36" (914mm) away from combustible materials such as curtain drapes,
furniture, bedding, paper, etc.
B. Have two people hold the appliance against the wall to determine the
nal location.
C. Remove the bracket from the back of the unit by removing the two
screws, refer to Figure 1.
D. Mark out location, then mount the bracket onto the wall using the 8
supplied screws. This bracket MUST have the hooks facing upward
and be level. NOTE: It is strongly recommended that the mounting
bracket be screwed into the wall studs where possible. If the wall studs cannot be used, ensure
that the supplied plastic
anchors are used to af x
the bracket to the wall and
the bracket is adequately
secured.
E. With the wall mounting
bracket installed have two
people lift the appliance up and insert the two hooks on the bracket into the two slots on the back of
the appliance.
F. Check the appliance for stability ensuring that the bracket will not pull free from the wall.
SIDE VIEW
BODY
FLOOR
GLASS FRONT
17 1/8"
435mm
WALL MOUNT
BRACKET
SCREWS
HOOK
HOOK
3.3 INSTALLING THE APPLIANCE
BRACKET
FIG. 1
Measurements are taken from the body.
Sides, back and top 0"
A. Once the rough opening has been prepared, and the power has been routed to the left side of the
recess, the appliance may be installed.
B. Lift the appliance up to the opening, maintaining the 0.5" (12.7mm) clearance to the sides.
C. The electrical connection must be made prior to sliding the appliance into place. (See "HARD WIRE
INSTALLATION" section.)
D. Using the 4 screws provided, level the appliance and use the retaining brackets to secure the
appliance to the to the wall.
NOTE: In order to avoid the possibility of exposed insulation or vapour barrier coming in contact
with the appliance body, it is recommended that the walls of the appliance enclosure be " nished"
(ie. drywall/sheetrock), as you would nish any other outside wall of a home. This will ensure that
clearance to combustibles is maintained within the cavity.
17 1/2"
445mm
45"
1143mm
3 1/2"
89mm
17 1/2"
445mm
45"
1143mm
MIN
Finishing Material
Due to the many different nish materials used on walls, it is highly recommended that you consult your local
builder before you install this appliance in the wall.
Select a location that is not prone to moisture and is located at least 36" (914.4mm) away from combustible
materials such as curtain drapes, furniture, bedding, paper etc.
3.4 RECESSING INSTALLATION
3.4.1 MINIMUM CLEARANCE TO COMBUSTIBLES
3.4.2 FRAMING
(NON-LOAD
BEARING)
EN
W415-1223 / B / 10.11.18
9
3.4.3 MOUNTING BRACKET INSTALLATION
A. Remove the glass front, refer to "GLASS FRONT INSTALLATION" section for removal instructions.
B. Remove the crystals from the appliance prior to installing the mounting brackets.
C. Prior to installing the mounting brackets determine how you will be recessing the appliance.
NOTE: The appliance cannot be mounted ush against the wall.
D. Secure two mounting brackets to each side of the appliance use the appropriate holes, as illustrated
in the illustration below, using the 8 screws provided to secure the mounting brackets to the appliance.
E. Level the appliance and secure the brackets to wall using the 4 screws provided.
MOUNTING
BRACKET
NOTE: Two sets of holes are provided. The wall structure may limit how far the appliance
can be recessed. Use the appropriate set of holes.
EN
W415-1223 / B / 10.11.18
10
3.5 HARD WIRING INSTALLATION
HARD WIRING CONNECTION
If it is necessary to hard wire this appliance, a quali ed electrician must remove the cord connection, and wire
the appliance directly to the house hold wiring.
This appliance must be electrically connected and grounded in accordance with local codes, if hard wired. In
the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada or the
current ANSI/NFPA 70 NATIONAL ELECTRICAL CODE in the United States.
!
WARNING
TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED SERVICE
PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.
A. Remove the cover plate from the right side of
the appliance by removing the four screws, as
shown above.
COVER PLATE
B. Remove the wire connectors from the power
cord.
The power cord may be discarded.
NOTE: Leave enough wire so that the appliance can be removed from the enclosure without
disconnecting the power supply.
C. Take the new cover plate, supplied in the manual bag. Punch out the 7/8" (22.2mm) hole and install a
box connector through, into the junction box. Snap the box connector clamp onto the supply wires.
D. Using the wire connectors, connect the common blue wires (B) and white wires (W) together, then
hot black wires (B1) and then the ground green wires (G), refer to Figure 3.
E. Reinstall the cover plate using the four screws, as shown in step A.
Fig. 1
Fig. 2
Fig. 3
7/8" (22.2mm)
Diameter
G
B1
B
W
EN
W415-1223 / B / 10.11.18
11
EN
W415-1223 / B / 10.11.18
12
4.0 FINISHING
!
WARNING
POWER SUPPLY SERVICE MUST BE COMPLETED PRIOR TO FINISHING TO AVOID
RECONSTRUCTION.
HEAT VENTS AND AIR OPENINGS CANNOT BE COVERED IN ANY CIRCUMSTANCES.
4.1 GLASS DOOR REMOVAL
A. Remove the 8 screws, as shown in the illustration below.
B. Tilt the top of the door forward until you can hold the sides of the door. Lift the door up and out of the
bottom retainer.
!
WARNING
THE DOOR LATCHES ARE PART OF A SAFETY SYSTEM AND MUST BE PROPERLY ENGAGED. DO
NOT OPERATE THE APPLIANCE WITH LATCHES DISENGAGED.
FACING AND/OR FINISHING MATERIALS MUST NOT INTERFERE WITH AIR FLOW THROUGH AIR
OPENINGS, LOUVRES OPENINGS, OPERATION OF LOUVRES OR DOORS OR ACCESS FOR
SERVICE. OBSERVE ALL CLEARANCES WHEN APPLYING COMBUSTIBLE MATERIALS.
BEFORE DOOR IS REMOVED TURN THE APPLIANCE OFF AND WAIT UNTIL APPLIANCE IS COOL TO
THE TOUCH. DOORS ARE HEAVY AND FRAGILE SO HANDLE WITH CARE.
4.2 CRYSTAL EMBER INSTALLATION
Glass front must be removed and the appliance must be mounted in its nal location before the crystal embers
are installed.
A. CLEAN CRYSTAL MEDIA: Crystal media may have a ne oil
residue that needs to be cleaned prior to installation. Clean the
crystal with mild dish soap, drain, rinse thoroughly and dry before
placing into the tray.
B. Carefully place crystal embers into the bottom tray on the front of
the appliance as illustrated. Apply an even layer from side to side.
EN
W415-1223 / B / 10.11.18
13
5.0 OPERATING INSTRUCTIONS
Once the appliance has been plugged into a grounded electrical outlet, it is ready to operate.
NOTE: Ensure the house circuit breakers for the power supply are turned on. In the event of a power
failure, when the main power switch of the appliance is in the "I" ON position and the hand held remote
control is in the OFF position, the ame generation lights will come back on at the high setting, when
the power supply returns.
The Main Power Switch is located on the bottom right side of the appliance as illustrated.
The "|" indicates ON and "O" indicates OFF. Push the switch to "|" to turn
on the appliance and the ame
effect.
5.1 MAIN POWER SWITCH
NOTE: Make certain new batteries are installed correctly.
A. Plug in your electric appliance.
B. Make certain the appliance’s Main Power Switch is at the ON position! The remote control will NOT
work if the Main Power Switch is at the OFF position.
C. When operating the remote control, it must be directed towards the front center of
the appliance.
D. The
button at the top left of the remote can be used to power up or down the
appliance (the main power switch on the appliance must be in the ON position for
the remote to operate). Pressing this button activates the power to the appliance.
E. To activate ame, press the "FLAME"
button and then to adjust the ame
height press the “
+5” or “ -5” buttons. There are ve levels of ame effects.
F. To activate the heater, press the "HEAT"
button. The initial set-up heat level
will be set for high heat, to adjust the heat level choose the
button for high
heat (1500W) or
button for low heat (750W). Adjusting to auto control by room
temperature press the "ROOM TEMP"
button, the heater turns on when room
temperature is below 21°C. the heater will turn off when the room temperature is
above 25°C.
G. To adjust the blue ame press the “
+5” or “ -5” buttons. There are ve levels
of ame effects.
H. To turn off the appliance, press the button
once.
NOTE: This remote control must remain within 8 meters or 26 feet of the appliance to be effective
and this range may be reduced as the battery power is depleted.
POWER
SWITCH
5.2 OPERATING BY REMOTE CONTROL
BOTTOM VIEW
EN
W415-1223 / B / 10.11.18
14
6.0 MAINTENANCE
6.1 FUSE REPLACEMENT
!
WARNING
PREPARATION FOR MAINTENANCE
ALWAYS DISCONNECT THE POWER AND ALLOW THE ELECTRIC APPLIANCE TO COOL BEFORE
PERFORMING ANY CLEANING, MAINTENANCE OR RELOCATION OF THIS ELECTRIC APPLIANCE.
TURN CONTROLS TO OFF AND REMOVE PLUG FROM OUTLET OR TURN OFF THE HOUSE
CIRCUIT BREAKER TO ELECTRIC APPLIANCE RECEPTACLE.
DO NOT INSTALL REPLACEMENT LAMPS THAT EXCEED SPECIFIED MAXIMUM WATTS.
THE HALOGEN LAMPS IN YOUR APPLIANCE CAN BECOME EXTREMELY HOT. ALLOW AT LEAST
10 MINUTES BETWEEN TURNING OFF THE APPLIANCE AND REMOVING THE LAMPS TO AVOID
ACCIDENTAL BURNS.
DO NOT HANDLE THE LAMP WITH BARE FINGERS, OILS FROM YOUR SKIN WILL DAMAGE THE
LAMPS WHEY THEY HEAT UP. USE GLOVES OR A CLEAN DRY CLOTH WHEN HANDLING LAMPS.
To replace the fuse remove the glass door see "GLASS DOOR REMOVAL" section.
A. Remove the glass media from the appliance, glass embers may have sharp edges,
wear safety glasses and gloves when handling.
B. Remove 4 screws on each side of the appliance that secure the rebox front and
mirror glass holder and remove from the appliance, the circuit board will become
visible, as shown below
C. Remove the mirror glass prior to accessing the circuit board.
D. Remove the fuse cover to gain access to the fuse and replace the existing fuse with
the new fuse.
FUSE COVER
SIDE VIEW
GLASS
FRONT
EN
W415-1223 / B / 10.11.18
15
#1
#1 Main power switch wire
#2 Motor wire
#3 Heater level 2 wire
#4 Heater level 1 wire
F1
FUSE2
T6
8050
T5
8050
T7
8050
RELAY-H2
RELAY-H1
RELAY-MOTOR
R3
10K
S1
P-SW
H2
H1
MOTOR
C7
35V 680uF
t
25*C,5K
THERMISTOR
1
2
3
4
5
6
SIP2
2.4*7
R7
510
R6 510
R12
510
R10
510
R11
510
1
2
TEMP
2.4*2
L1
N
H2 PH-2
6.3*0.8
6.3*0.8
MOTOR
H1+FAN
6.3*0.8
P-NI
6.3*0.8
D2
1N4007
D3
1N4007
D5
1N4007
VSS
VDD
20
10
P0.1
P4.1/AIN1
P4.2/AIN2
P0.4
P5.3
P5.2
P0.5
P0.6
P0.7
8
P5.0
P5.1
SN8P2722
2
15
16
5
12
11
3
9
10
PH-4
6.3*0.8
N
P-L
6.3*0.8
TEMP_BRK
PH-7
6.3*0.8
PH-6
6.3*0.58
PTC
+5V
R8
10K
C2
104
C5
104
R5
10K
LED1
D1
T1
SS8050
R?
180
DS?
LED3
DS?
LED2
R?
180
1
2
LED-HY
2.4*2
1
2
FIRE-B
2.4*2
LED6
LED5
T2
SS8050
100
LED8LED7
R?
100
1
2
LED-HB
2.4*2
1
2
FIRE-Y
2.4*2
+12V
+12V
+12V
FAN MOTOR
6
P0.2
7
C4
C6
5v
25V 47uF
104
HS0038
BUZ1
D1
4007
T3
SS8050
R4
510
+5V
R2
1K
R9
510
LED6
LED5
T4
SS8050
180
LED8
LED7
R?
100
1
2
LED-M
2.4*2
1
2
LAMP
2.4*2
+12V
+12V
+12V
C13
400V 22U
6mH
L2
AC
1
V+
2
AC
3
V-
4
D9
2KBP06M
C14
400V 22U
R17
1M
R16
2M
R15
2M
EF1
D7
FR106
D8
P6KE200
C12
16V 10U
4
TNY278PN
TNY1
1
2
5-8
C10
2.2nF/250VAC
C11
2.2nF/250VAC
U1B
LTV817A
U1A
LTV817A
C9
390PF
R13
27
D4 SB3100
D6
12V
L1
3.3uH
C8
100U 16V
+12V
GND
GND
GND
GND
Vin
1
GND
2
Vout
3
7805IC1
C1
1KU/16V
C3
104
R1
100/0.5W
+5V
R14
1K
1
2
7
6
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
#2
#3 #4
7.0 WIRING DIAGRAM
!
WARNING
TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A QUALIFIED SERVICE
PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.
EN
W415-1223 / B / 10.11.18
16
Contact your dealer or the factory for questions concerning prices and policies on replacement parts. Normally
all parts can be ordered through your Authorized dealer / distributor.
FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF THE
ORIGINAL INVOICE WILL BE REQUIRED TO HONOUR THE CLAIM.
When ordering replacement parts always give the following information:
Model & Serial Number of appliance
Installation date of appliance
• Part number
Description of part
• Finish
* IDENTIFIES ITEMS WHICH ARE NOT ILLUSTRATED. FOR FURTHER INFORMATION, CONTACT YOUR
AUTHORIZED DEALER.
FAILURE TO POSITION THE PARTS
IN ACCORDANCE WITH THIS
MANUAL OR FAILURE TO USE ONLY
PARTS SPECIFICALLY APPROVED
WITH THIS APPLIANCE MAY
RESULT IN PROPERTY DAMAGE OR
PERSONAL INJURY.
!
WARNING
For after sales service, please call 1-866-820-8686
NOTE: Care must be taken when removing and disposing of any broken glass or damaged
components. Be sure to vacuum up any broken glass from inside the appliance before operation.
8.0 REPLACEMENT PARTS
8
5
BLUE LIGHT
+5 MAX-5 OFF
TEMPLOWHIGH
FLAME
+5 MAX-5 OFF
HEAT
1
6
2
3
4
9
12
13
7
14
COMPONENTS
REF NO. PART NO. DESCRIPTION
1 W405-0012 LED CIRCUIT BOARD FOR EMBER BED
2 W190-0064 CIRCUIT BOARD
3 W062-0050 BLOWER AND HEATER ASSEMBLY
4 W660-0128 SWITCH (RK1-11)
5 W190-0051 REMOTE CONTROL
6 W300-0176 FRONT GLASS
7 W300-0177 MIRROR GLASS
8 W010-3079 DRUM ASSEMBLY
9 W660-0129 REMOTE RECEIVER
10* W300-0178 CRYSTAL, 0.54kg (1.2lbs)
11* W435-0055 MOTOR, 120V 30/36RPM
12 W080-1371 MOUNTING BRACKET
13 W285-0006 FUSE
14 W020-0880 HARDWARE KIT
EN
W415-1223 / B / 10.11.18
17
9.0 TROUBLESHOOTING
SYMPTOM PROBLEM TEST SOLUTION
Dim or no ame Drum LED’s are burnt out Inspect the LED’s inside the ame generation cylinder drum
(W010-2918) and replace them if necessary
Ember bed is not
glowing or dimming
Ember LED’s are burnt out Inspect the ember bed LED’s (W405-0008) and replace them if
necessary
No warm air coming
out of appliance
Room temperature is higher
than the appliance setting (if
it is set to room temperature)
Heater is burnt out
Set the appliance to a high or low heat setting.
Inspect the burner and heater assembly (W062-0047) and
replace it if necessary
Appliance turns off
and will not turn on
Appliance has overheated
and safety device has
caused the thermal switch to
disconnect
Unplug the appliance, allow appliance to cool for 15 minutes,
then plug it back in
House circuit breaker has
tripped
Appliance’s fuse has blown
Reset house circuit breaker
Replace the fuse
Appliance will not
come on when
switch is ipped to
ON
Appliance is not plugged into
an electrical outlet
Check plug and plug it in
Appliance has overheated
and safety device has
caused the thermal switch to
disconnect
Circuit board is burnt out
Unplug the appliance, allow appliance to cool for 15 minutes,
then plug it back in
Inspect the circuit board (W190-0050) and replace it if
necessary
Remote control
does not work
Low batteries Replace batteries in remote control
Heater shuts off
automatically
Room is too warm The heater has a built-in thermostat so it will shut off
automatically once the pre-set temperature is reached. It will
also turn on automatically if the room temperature drops below
the pre-set temperature
!
WARNING
TURN OFF THE APPLIANCE COMPLETELY AND LET COOL BEFORE SERVICING. ONLY A
QUALIFIED SERVICE PERSON SHOULD SERVICE AND REPAIR THIS ELECTRIC APPLIANCE.
EN
W415-1223 / B / 10.11.18
18
10.0 WARRANTY
NAPOLEON warrants its products against manufacturing defects to the original purchaser only. Registering your warranty is not necessary.
Simply provide your proof of purchase along with the model and serial number to make a warranty claim. NAPOLEON reserves the right to have
its representative inspect any product or part thereof prior to honouring any warranty claim. Provided that the purchase was made through an
authorized NAPOLEON dealer your appliance is subject to the following conditions and limitations:
Warranty coverage begins on the date of original installation.
This factory warranty is non-transferable and may not be extended whatsoever by any of our representatives.
Installation must be done in accordance with the installation instructions included with the product and all local and national building and re codes.
This limited warranty does not cover damages caused by misuse, lack of maintenance, accident, alterations, abuse or neglect and parts installed
from other manufacturers will nullify this warranty.
This limited warranty further does not cover any scratches, dents, corrosion or discoloring caused by excessive heat, abrasive and chemical
cleaners nor chipping on porcelain enamel parts, mechanical breakage of PHAZER™ logs.
In the rst year only, this warranty extends to the repair or replacement of warranted parts which are defective in material or workmanship provided
that the product has been operated in accordance with the operation instructions and under normal conditions.
NAPOLEON will not be responsible for installation, labour or any other expenses related to the reinstallation of a warranted part and such
expenses are not covered by this warranty. Notwithstanding any provisions contained in the Limited Warranty, NAPOLEON’s responsibility under
this warranty is de ned as above and it shall not in any event extend to any incidental, consequential or indirect damages.
This warranty de nes the obligations and liability of NAPOLEON with respect to the NAPOLEON electric appliance and any other warranties
expressed or implied with respect to this product, its components or accessories are excluded.
NAPOLEON neither assumes, nor authorizes any third party to assume, on its behalf, any other liabilities with respect to the sale of this product.
Any damages to appliance, brass trim or other component due to water, weather damage, long periods of dampness, condensation, damaging
chemicals or cleaners will not be the responsibility of NAPOLEON.
The bill of sale or copy will be required together with a serial number and a model number when making any warranty claims from your authorized
dealer. The warranty registration card must be returned within fourteen days to register the warranty.
NAPOLEON reserves the right to have its representative inspect any product or part thereof prior to honouring any warranty claim.
All parts replaced under the Limited Warranty Policy are subject to a single claim.
All parts replaced under the warranty will be covered for a period of 90 days from the date of their installation.
The manufacturer may require that defective parts or products be returned or that digital pictures be provided to support the claim. Returned
products are to be shipped prepaid to the manufacturer for investigation. If a product is found to be defective, the manufacturer will repair or
replace such defect.
Before shipping your appliance or defective components, your dealer must obtain an authorization number. Any merchandise shipped without
authorization will be refused and returned to sender.
Shipping costs are not covered under this warranty.
Additional service fees may apply if you are seeking warranty service from a dealer.
NAPOLEON electric appliances are manufactured under the strict Standard of the world recognized
ISO 9001 : 2008 Quality Assurance Certi cate.
NAPOLEON products are designed with superior components and materials, assembled by trained craftsmen who take
great pride in their work. Once assembled the complete appliance is thoroughly inspected by a quali ed technician before
packing to ensure that you , the customer, receive the quality product that you expect from NAPOLEON.
Electrical components and wearable parts such as fan/heater, motors, switches, nylon bearing components and remote
controls are covered and NAPOLEON will provide replacement parts free of charge during the rst year of limited warranty.
Light bulbs and fuses are NOT covered by the warranty.
Any labour related to warranty repair is not covered.
* Construction of models vary. Warranty applies only to components included with your speci c appliance.
NAPOLEON ELECTRIC APPLIANCE LIMITED WARRANTY
CONDITIONS AND LIMITATIONS
ALL SPECIFICATIONS AND DESIGNS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE DUE TO ON-GOING PRODUCT IMPROVEMENTS.
NAPOLEON IS A REGISTERED TRADEMARK OF WOLF STEEL LTD.
EN
W415-1223 / B / 10.11.18
19
11.0 SERVICE HISTORY
Other Napoleon
®
Products
'JSFQMBDF*OTFSUTt$IBSDPBM(SJMMT
t(BT'JSFQMBDFTt8BUFSGBMMTt8PPE4UPWFT
)FBUJOH$PPMJOHt&MFDUSJD'JSFQMBDFTt0VUEPPS'JSFQMBDFTt(BT(SJMMT
'JSFQMBDFT)FBUJOH$PPMJOHDBMMt(SJMMTDBMM
napoleonproducts.com
/BQPMFPO3PBE#BSSJF0OUBSJP$BOBEB-.(
#BZWJFX%SJWF#BSSJF0OUBSJP$BOBEB-/:
.JMMFS%SJWF$SJUUFOEFO,FOUVDLZ64"
5SBOT$BOBEB)JHIXBZ.POUSFBM2VFCFD$BOBEB)5"
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

NAPOLEON NLF50H Manuel utilisateur

Catégorie
Cheminées
Taper
Manuel utilisateur

dans d''autres langues