Sun Microsystems StorEdge A5000 Product Notes

Taper
Product Notes
901 San Antonio Road
Palo Alto, CA 94303-4900 USA
1 650 960-1300 fax 1 650 969-9131
A Sun Microsystems, Inc. Business
Sun Microsystems Computer Company
Part No.: 805-1018-13
Revision A, June 1998
Sun
StorEdge
A5000
Product Notes
FormerlytheSun
EnterpriseNetworkArray
Send comments about this document to: [email protected]
Copyright 1998 Sun Microsystems,Inc.901SanAntonioRoadPaloAlto,CA94303 USA. Allrights reserved.
This produc1998t or document is protectedby copyright and distributed under licenses restrictingits use, copying, distribution, and
decompilation. No partof this productor document may be reproducedin any form by anymeans without prior written authorizationof Sun
and its licensors,if any. Third-party software,including font technology, is copyrighted and licensed from Sun suppliers.
Parts of theproductmay be derived fromBerkeley BSD systems, licensed from the University of California. UNIXis a registered trademark in
the U.S. andother countries, exclusively licensed through X/Open Company, Ltd.
Sun, Sun Microsystems, the Sun logo, AnswerBook, SunSolve Online, Sun StorEdge, SunStorEdge Volume Manager, Sun Enterprise Volume
Manager,Solstice DiskSuite, Enterprise, Sun Enterprise Network Array, and Solaris aretrademarks, registeredtrademarks, or service marks of
Sun Microsystems, Inc. in the U.S. and other countries. All SPARC trademarks are used underlicense and are trademarks or registered
trademarks of SPARCInternational, Inc. in the U.S. and other countries. Productsbearing SPARCtrademarks are based upon anarchitecture
developed by Sun Microsystems, Inc.
The OPEN LOOKand Sun™ Graphical UserInterface was developed by SunMicrosystems,Inc. for its users and licensees. Sun acknowledges
the pioneering efforts of Xeroxin researchingand developing the concept of visual or graphical user interfaces for the computer industry. Sun
holds a non-exclusivelicense fromXerox to the Xerox Graphical User Interface, which license also coversSun’s licensees who implementOPEN
LOOK GUIs andotherwise comply with Sun’swritten license agreements.
RESTRICTEDRIGHTS: Use, duplication, or disclosure by the U.S. Government is subject to restrictions of FAR 52.227-14(g)(2)(6/87) and
FAR52.227-19(6/87), or DFAR 252.227-7015(b)(6/95) and DFAR 227.7202-3(a).
DOCUMENTATION IS PROVIDED “AS IS” AND ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES,
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-
INFRINGEMENT, ARE DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID.
Copyright 1998 Sun Microsystems, Inc., 901 San Antonio Road Palo Alto, CA94303 Etats-Unis. Tous droits réservés.
Ce produit ou document est protégépar un copyright et distribué avec des licences qui en restreignentl’utilisation, la copie, ladistribution, et la
décompilation. Aucune partiede ce produitou document ne peut êtrereproduitesous aucune forme, par quelque moyen que ce soit, sans
l’autorisation préalable etécrite de Sun etde ses bailleurs de licence,s’il y en a. Lelogiciel détenu par destiers, et qui comprend la technologie
relativeaux polices de caractères,est protégé par un copyright et licenciépar des fournisseurs de Sun.
Des parties dece produitpourront être dérivées des systèmes Berkeley BSD licenciés par l’Université de Californie.UNIX est une marque
déposée aux Etats-Uniset dans d’autrespays et licenciée exclusivement par X/Open Company, Ltd.
Sun, Sun Microsystems, le logo Sun, AnswerBook, SunSolve Online, Sun StorEdge, SunStorEdge Volume Manager, Sun Enterprise Volume
Manager,Solstice DiskSuite, Sun Enterprise, Sun Enterprise Network Array, et Solaris sont des marques de fabrique ou des marquesdéposées,
ou marques de service, de Sun Microsystems,Inc. aux Etats-Unis et dans d’autres pays. Toutesles marques SPARC sont utilisées sous licence et
sont des marques de fabrique ou des marquesdéposées de SPARC International,Inc. aux Etats-Unis etdans d’autrespays. Les produits portant
les marquesSPARC sontbasés sur une architecturedéveloppée par Sun Microsystems, Inc.
L’interfaced’utilisation graphique OPEN LOOK et Sun™ a été développée par Sun Microsystems,Inc. pour ses utilisateurs et licenciés. Sun
reconnaîtles effortsde pionniers de Xerox pour la recherche et le développement du concept des interfaces d’utilisation visuelle ou graphique
pour l’industrie del’informatique. Sun détient une licencenon exclusive de Xerox sur l’interface d’utilisation graphique Xerox,cette licence
couvrant également leslicenciés de Sun quimettent en place l’interface d’utilisationgraphique OPEN LOOK et quien outrese conforment aux
licences écrites deSun.
CETTE PUBLICATION EST FOURNIE "EN L’ETAT" ET AUCUNE GARANTIE, EXPRESSE OU IMPLICITE, N’EST ACCORDEE, Y
COMPRIS DES GARANTIES CONCERNANT LA VALEUR MARCHANDE, L’APTITUDE DE LA PUBLICATION A REPONDRE A UNE
UTILISATION PARTICULIERE, OU LE FAIT QU’ELLE NE SOIT PAS CONTREFAISANTE DE PRODUIT DE TIERS. CE DENI DE
GARANTIE NE S’APPLIQUERAIT PAS, DANS LA MESURE OU IL SERAIT TENU JURIDIQUEMENT NUL ET NON AVENU.
1
Sun StorEdge A5000
Product Notes
The Sun StorEdge A5000 Product Notes provides product notes for the Sun™
StorEdge™ A5000 disk array. This information includes:
Supplemental installation notes
Sun StorEdge A5000 Installation and Service Manual changes
Data migration
Supplemental Installation Notes
For a complete list of required patches, as well as known bugs, access the “Storage &
Peripherals” section of the docs.sun.com
sm
web site and read the Sun StorEdge
A5000 Installation Supplement:
http://docs.sun.com
Patches listed in the Sun StorEdge A5000 Installation Supplement or other
documentation can be downloaded from the SunSolve Online™ Public Patch Page
Access web site:
http://sunsolve.sun.com/sunsolve/pubpatches/patches.html
Contact your service provider if you cannot access these web sites.
2 Sun StorEdge A5000 Product Notes June 1998
Installation and Service Manual
This section supplements information in the Sun StorEdge A5000 Installation and
Service Manual, part number 802-7573.
Handling Fiber Optic Cables
Caution Follow these guidelines to avoid causing damage to fiber optic cables.
The maximum bend radius for fiber optic cables is 2 inches (5.1 cm). However, a
bend radius of not less than 6 inches (15.2 cm) is preferable.
Make sure to grasp the connector when disconnecting a fiber optic cable. Never
disconnect a fiber optic cable by pulling on the cable.
To avoid damage due to contamination or abrasion, always put dust covers on the
fiber optic cable connectors when the cable is disconnected.
Data Migration
This section describes how to migrate data from SPARCstorage™ arrays to Sun
StorEdge A5000 disk arrays. It includes procedures for migrating data using Sun
StorEdge Volume Manager™ or Solstice™ DiskSuite™ to new Sun StorEdge Volume
Manager software.
Do not perform the procedures in this section unless you are an experienced system
administrator or a service-trained maintenance provider.
Note This chapter does not cover migration to Solstice DiskSuite software. Refer
to the Solstice DiskSuite User's Guide, part number 802-4215, and the Solstice DiskSuite
Reference Guide, part number 802-6724.
Note Sun StorEdge Volume Manager was formerly know as Sun™ Enterprise
Volume Manager™.
Sun StorEdge A5000 Product Notes 3
1. Determine which version of the Solaris operating environment you are running.
Look at the /etc/release file to make sure the operating system installed is at
least Solaris 2.5.1 Hardware: 8/97. If your system doesn’t have an /etc/release
file, it may not be running Solaris 2.5.1 Hardware: 8/97.
2. Verify the version of Sun StorEdge Volume Manager or Solstice DiskSuite
software that you are currently using.
If your system does not have at least Sun StorEdge Volume Manager 2.4, you must
upgrade or install Sun StorEdge Volume Manager later in this procedure.
3. Become superuser and exit the operating system.
To inform any mounted users that the system will be going down, use the shutdown
command. Otherwise, use the init 0 command. See the man pages for these
commands or the Solaris AnswerBook™ online documentation.
4. Power off the system.
Refer to the service documentation that came with your system.
5. Install new host adapters or SBus+ I/O boards.
Refer to the service documentation that came with your system or peripheral.
(The SBus+ I/O board, also referred to as I/O SBus Board with 100 Mbyte/sec Fibre
Channels, is available for Sun™ Enterprise™ 6x00, 5x00, 4x00, and 3x00 systems.)
6. Connect the fiber optic cable(s) between the host adapters or SBus+ I/O boards
and other devices in the loop(s).
Refer to the documentation that came with the devices for specific instructions.
7. Power on your peripherals and then your system.
Note If your system starts to reboot, interrupt the reboot process by
pressing the Stop-A keys.
The system should now be at the ok prompt. If a > prompt is showing, type
n to
switch to the ok prompt.
8. Reboot your system using the boot -r command.
9. Install or upgrade the Sun StorEdge Volume Manager software, if needed.
10. Install applicable Sun StorEdge Volume Manager software patches.
11. Upgrade the Solaris operating environment, if needed.
12. Install applicable Solaris patches.
13. Check the software installation using the luxadm command.
4 Sun StorEdge A5000 Product Notes June 1998
14. Set up Sun StorEdge Volume Manager volumes.
For systems already using Sun StorEdge Volume Manager software, just add the
disks in the StorEdge A5000 array(s). Otherwise, initialize the Sun StorEdge Volume
Manager software and then add the disks.
15. Copy data from the SPARCstorage array(s) to the StorEdge A5000 array(s).
If your data is on a volume that can be mirrored, add a new plex to the volume
using disks from your new array(s).
For any of the following conditions, use the dd command to copy the data from its
present location to a new location on the new array(s):
Data is on a volume that cannot be mirrored, such as a RAID 5 volume.
Data is managed by other disk management software, such as Solstice
DiskSuite.
Data is on disk partitions.
Refer to the Sun StorEdge Volume Manager System Administrators Guide, man pages,
or AnswerBook online documentation for more information.
16. Detach the old plexes and unconfigure the disk drives to be removed.
Refer to the Sun StorEdge Volume Manager System Administrators Guide.
17. Become superuser and exit the operating system.
18. Power off the system.
Refer to the service documentation that came with your system.
19. Remove any unused SBus I/O boards or FC SBus boards.
20. Power on your peripherals and then your system.
Note If your system starts to reboot, interrupt the reboot process by
pressing the Stop-A keys.
The system should now be at the ok prompt. If a > prompt is showing, type
n to
switch to the ok prompt.
21. Reboot your system using the boot -r command.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Sun Microsystems StorEdge A5000 Product Notes

Taper
Product Notes

dans d''autres langues