HearthStone DVI 44 Manuel utilisateur

Hearthstone Quality Home Heating Products, Inc. ®

DVI-44 Model 8860

Manual: 6400-404##

R: 8/2/2012

DVI 44

(Model 8860)

GAS-FIRED

DIRECT-VENT INSERT

Owner's Manual

Installation

&

Operating Instructions

Read This Manual in Its Entirety

Operate And Maintain This Gas Heater According

To This Instruction Manual.

SAVE THESE INSTRUCTIONS!

.

WARNING: FOLLOW THE INFORMATION IN THESE

INSTRUCTIONS EXACTLY, IF NOT, A FIRE OR

EXPLOSION MAY RESULT CAUSING PROPERTY

DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

WARNING: DO NOT STORE OR USE GASOLINE OR

ANY OTHER FLAMMABLE VAPORS AND LIQUIDS

NEAR THIS OR ANY OTHER GAS APPLIANCE.

WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.

Do not touch electrical switches; do not use the phone in

your building.

Immediately call your gas supplier from a phone outside

the structure. Follow your gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire

department or 911.

A qualified installer, service agency, or gas supplier must

perform installation and service of this appliance. In the

Commonwealth of Massachusetts, all installation of gas lines

and gas fittings must be performed by a licensed gas fitter or

licensed plumber.

AVERTISSEMENT: ASSUREZ-VOUS DE BIEN SUIVRE

LES INSTRUCTIONS DONNÉ DANS CETTE NOTICE

POUR RÉDUIRE AU MINIMUM LE RISQUE D’INCENDIE

OU POUR ÉVITER TOUT DOMMAGE MATÉERIEL,

TOUTE BLESSURE OU LA MORT.

AVERTISSEMENT: NE PAS ENTRESPOSER NI

UTILISER D’ESSENCE NI D’AUTRE VAPERURS OU

LIQUIDES INFLAMMABLES DANS LE VOISINAGE DE

CET APPRAREIL OU DE TOUT AUTRE APPAREIL.

QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:

Ne pas tenter d’allumer d’appareil.

Ne touchez à aucun interrupteur. Ne pas vous servir des

téléphones se trouvant dans le batiment où vous vous

trouvez.

Appelez immédiatement votre fournisseur de gaz depuis un

voisin. Suivez les instructions du fournisseur.

Si vous ne pouvez rejoindre le fournisseur de gaz, appelez

le service dos incendies.

L’installation et service doit être exécuté par un qualifié installer,

agence de service ou le fournisseur de gaz.

Intentionally Blank

Hearthstone Quality Home Heating Products, Inc. DVI-44 Model 8860

3

Information Sheet

Use this page to record all relevant information concerning the purchase, installation, and maintenance of your

DVI 44 Model 8860 Direct-Vent Fireplace Insert. This information will facilitate servicing, purchase of

replacement parts, and warranty claims (if necessary). Keep your original receipt as proof of purchase.

Serial Number:

Fuel type:

Natural Gas

Liquid Propane

Sold by:

Date of Purchase:

Address:

Phone:

E-mail

Website:

Installed by:

Date of Installation:

Address:

Phone:

E-mail

Website:

Gas Supplier:

Address:

Phone:

E-mail

Website:

Read this Owner’s Manual before installing, or operating your DVI 44. Retain this manual for future reference.

SERVICE RECORD

Date

Who Performed Work

Work Performed

Notes:

WHAT WHEN

Firebox Cleaning............. annually

Glass Cleaning................ as needed

Door Gasket.................... Replacement as needed

Hearthstone Quality Home Heating Products, Inc. DVI-44 Model 8860

4

Table of Contents

INTRODUCTION ........................................................................................................................................................... 5

SAFETY & GOOD PRACTICES ...................................................................................................................................... 6

SPECIFICATIONS ......................................................................................................................................................... 9

DVI 44 8860 Model Overview ................................................................................................................................... 11

Control Functions ..................................................................................................................................................... 14

INSTALLATION PREPARATION .................................................................................................................................... 16

Codes ....................................................................................................................................................................... 16

Items Required for Installation .................................................................................................................................. 16

Packing List .............................................................................................................................................................. 16

Unpacking and Inspection ........................................................................................................................................ 16

CLEARANCES TO COMBUSTIBLES .............................................................................................................................. 19

Clearance to Combustibles ...................................................................................................................................... 19

Hearth Requirement/Floor Protection ....................................................................................................................... 19

VENTING INFORMATION ............................................................................................................................................. 22

Venting Components ................................................................................................................................................ 22

ELECTRICAL SYSTEM INFORMATION .......................................................................................................................... 26

GAS SUPPLY & CONNECTIONS .................................................................................................................................. 27

Gas Connections ...................................................................................................................................................... 28

BAFFLE, LOG SET, & SCREEN PLACEMENT ............................................................................................................... 29

Installation of the Baffle ............................................................................................................................................ 29

Installation of the Log Set ......................................................................................................................................... 30

Completing the Installation ....................................................................................................................................... 30

Installation of the Screen .......................................................................................................................................... 31

Removal of Log Set .................................................................................................................................................. 31

Surround Installation ................................................................................................................................................. 32

Façade Installation ................................................................................................................................................... 32

LIGHTING & OPERATION ........................................................................................................................................... 33

Lighting Instructions .................................................................................................................................................. 33

Initial Adjustments .................................................................................................................................................... 33

Daily Operation ......................................................................................................................................................... 35

ROUTINE MAINTENANCE AND CARE ........................................................................................................................... 37

Cleaning ................................................................................................................................................................... 37

Monthly (or as needed): ............................................................................................................................................ 37

Annually: ................................................................................................................................................................... 37

As Needed: ............................................................................................................................................................... 39

REPLACEMENT PARTS & ACCESSORIES LIST ............................................................................................................. 40

TROUBLESHOOTING .................................................................................................................................................. 41

RATING LABEL ......................................................................................................................................................... 43

Hearthstone Quality Home Heating Products, Inc. DVI-44 Model 8860

5

Introduction

Congratulations on your purchase of the DVI 44

Model 8860, Gas-Fired Direct-Vent Insert. The DVI

44, by Hearthstone, incorporates the latest in direct

vent gas technology, which will provide you with

ease of use, clean, and efficient heat for years to

come. The DVI 44’s copious glass, sleek styling, and

enameled or painted façade options gives the DVI

44 ambiance and a pleasing look that enhances any

room.

However, as with any gas appliance, the unit must

be properly and safely installed and maintained by

qualified service personnel to ensure safe and

trouble-free operation.

DVI 44 Model 8860 features:

1. The most realistic looking gas fire available

today with highly detailed logs.

2. Heat Wave® refractory firebox liner to reflect the

heat into your room in the most efficient way

possible.

3. Real Platinum glowing embers, for instant glow

and realism.

4. Child safety screen to reduce the risk of severe

burns on the front glass.

5. Smart thermostatic remote control with split

burner technology for a full range of heat output.

6. Integral, quiet, and efficient room air circulating

fan – standard.

7. Battery backup to maintain basic functionality

during power outages (up to a week on fresh

batteries).

The Proflame System Features:

1. Thermostatic Remote Control

a. Twelve (12) flame levels, adjustable via

the remote

b. Split Burner control via remote

c. Six (6) blower speeds, adjustable via the

remote

d. Thermostatic mode to turn on/off based

upon room temperature.

e. “Smart” thermostatic mode to modulate

flame levels automatically as the unit

approaches the set point temperature.

f. Firebox Accent Light controlled by the

remote.

2. The option to toggle back and forth between an

Intermittent (IPI) or Continuous (CPI) pilot mode

via the remote.

a. The IPI (Summer) mode allows the most

efficient use of gas, burning the pilot

only when the thermostat calls for the

burner to ignite.

b. The CPI (Winter) mode runs the pilot

continuously keeping the firebox warmer

thus promoting better draft in colder

weather.

3. “Child-safe” lock-out on remote control.

4. “Low Battery” indicator for Transmitter on remote

control

Read this Owner’s Manual

Operate and maintain this gas heater according to

the instructions in this manual. For your safety, and

years of trouble free operation, read this manual in

its entirety.

Insert Must Be Installed and Maintained By

Qualified Service Personnel

Verify the gas connections and that venting systems

supply adequate combustion and ventilation air to

meet the requirements of local, regional or national

installation codes. Qualified service personnel must

inspect the gas heater before use, and at least

annually.

Manufactured & warranted by:

Hearthstone Quality Home heating Products, Inc.

317 Stafford Ave.

Morrisville, VT 05661

www.hearthstonestoves.com

inquiry@hearthstonestoves.com

Hearthstone Quality Home Heating Products, Inc. DVI-44 Model 8860

6

Safety & Good Practices

Your DVI 44 is an attractive and extremely efficient

and easy to use heater, utilizing today’s best

technologies. By following a few simple safety

precautions and by performing minimal

maintenance, the unit will remain appealing while

providing years of quality performance.

The installation must conform to local codes or, in

the absences of local codes, the current National

Fuel Gas Code, ANSI Z223.1 (NFPA 54) or

CAN/CGA B149 Installation Code. (Installer

l’appareil selon les codes ou réglements locaux, ou,

en l’absence de tells réglements, selon les Codes

d’installation CAN/CGA B149.)

CAUTION: DO NOT USE THIS APPLIANCE IF ANY

PART WAS UNDER WATER. IMMEDIATELY CALL

A QUALIFIED SERVICE TECHNICIAN TO INSPECT

THE HEATER AND TO REPLACE ANY PART OF

THE CONTROL SYSTEM AND GAS CONTROL

THAT HAS BEEN UNDER WATER. (NE PAS SE

SERVIR DE CET APPAREIL S’IL A ÉTÉ PLONGÉ

DANS L’EAU, COMPLÉTEMENT OU EN PARTIE.

APPELER UN TECHNICIEN QUALIFIÉ POUR

INSPECTOR L’APPAREIL ET REMPLACER TOUTE

PARTIE DU SYSTÉME DE CONTRÔLE ET TOUTE

COMMANDE QUI ONT ÉTÉ PLUNGES DANS

L’LAU.)

During the first few hours of operation the appliance

may produce smoke and/or odor. This is normal

during the first several burns and also after long

periods when the stove is not burned. During these

initial burns, open a window(s) to assist in the

removal of the smoke/odor.

The appliance and its individual shutoff valve must

be disconnected from the gas supply piping system

during any pressure testing of that system at test

pressures in excess of ½ psig. (3.5k Pa). The

appliance must be isolated from the gas supply

piping system by closing its individual manual

shutoff valve during any pressure testing of the gas

supply piping system at test pressures equal to or

less than ½ psig (3.5k Pa).

Fire Hazard

Do not store or use gasoline, other flammable

vapors or liquids in the vicinity of this appliance.

Locate the DVI 44 out of traffic areas and away from

furniture, draperies, clothing, and flammable

material.

Vent Only to the Outside

Never vent the gas heater to other rooms or

buildings.

Service Caution

If you believe your DVI 44 is not in any way

performing properly, immediately discontinue

operation until the unit is inspected and approved by

qualified service personnel. Prior to servicing the

unit, turn the gas to the valve off, and disconnect

any electrical source. Ensure the unit is cool prior to

servicing and cleaning. Replace any safety screen,

guard, or component removed during servicing

prior to operation. (Tout écran ou protecteur retiré

pour permettre l’entretien de l’appareil doit être remis

en place avant de mettre l’appareil en marche.) Use of

any components not supplied by Hearthstone on the

stove voids all warranties. Do not substitute

components.

Proper Fuel

This gas heater is designed to burn natural gas (NG)

or with conversion, liquid propane (LP). Never burn

any fuel gas not intended for use with this unit.

Never burn paper, wood, or other materials in this

appliance.

This heater is factory equipped to burn natural gas

(NG). To burn propane (LP), you must purchase an

LP conversion kit 98-56601.

This appliance is only for use with the type(s) of gas

indicated on the rating plate. This appliance is not

convertible for use with other gases, unless a

certified kit is used. Cet appareil doit être atilisé

uniquement avec les types de gas indiqués sur la

plaque signalétique. Ne pas l’utiliser avec d’autres

gas sauf si un kited conversion certifié est installé. )

WARNING: THIS GAS APPLIANCE MUST NOT BE

CONNECTED TO A CHIMNEY FLUE SERVING A

SEPARATE GAS OR SOLID-FUEL BURNING

APPLIANCE

WARNING: DO NOT OPERATE THE APPLIANCE

WITH THE FRONT GLASS REMOVED, CRACKED,

OR BROKEN. REPLACEMENT OF GLASS

SHOULD BE DONE BY A LICENSED OR

QUALIFIED SERVICE PERSON. ONLY OPEN

FRONT FOR ROUTINE SERVICE. DO NOT SLAM

FRONT OR STRIKE GLASS. AVERTISSEMENT. NE

PAS UTILISER L’APPAREIL SI LE PANNEAU

FRONTAL EN VERRE N’EST PAS EN PLACE, EST

CRAQUÉ OU BRISÉ. CONFIEZ LE

REMPLACEMENT DU PANNEAU À UN

TECHNICIEN AGRÉÉ.

WARNING: HEARTHSTONE RECOMMENDS THAT

ONLY AN NFI CERTIFIED SERVICE TECHNICIAN

INSTALLS, AND REPAIRS THIS APPLIANCE. A

QUALIFIED SERVICE TECHNICIAN MUST

Hearthstone Quality Home Heating Products, Inc. DVI-44 Model 8860

7

INSPECT THE APPLIANCE BEFORE USE, AND AT

LEAST ANNUALLY. MORE FREQUENT CLEANING

MAY BE REQUIRED DUE TO EXCESSIVE LINT

FROM CARPETING, BEDDING MATERIAL, PETS,

ETC. IT IS IMPERATIVE THAT THE CONTROL

COMPARTMENTS, BURNERS, AND CIRCULATING

AIR PASSAGES OF THE APPLIANCE ARE KEPT

CLEAN AND FREE OF OBSTRUCTIONS.

(L’INSTALLATION ET LA RÉPARATION DEVRAIT

ÊTRE CONFIÉES À UN TECHNICIEN QUALIFIÉ.

L’APPAREIL DEVRAIT FAIRE L’OBJET D’UNE

INSPECTION PAR UN TECHNICIEN

PROFESSIONNEL AVANT D’ÊTRE UTILISÉ ET AU

MOINS UNE FOIS L’AN PAR LA SUITE. DES

NETTOYAGES PLUS FRÉQUENTS PEUVENT

ÊTRE NÉCESSAIRES SI LES TAPIS, LA LITERIE,

ET CETERA PRODUISENT UNE QUANTITÉ

IMPORTANTE DE POUSSIÈRE. IL EST ESSENTIEL

QUE LES COMPARTIMENTS ABRITANT LES

COMMANDES, LES BRÛLEURS ET LES

CONDUITS DE CIRCULATION D’AIR DE

L’APPAREIL SOIENT TENUS PROPRES)

Hot Surfaces

Certain exposed surfaces of the DVI 44 will reach

high temperatures during normal operation.

Clearances to combustibles must be maintained, as

specified in the “Clearances To Combustibles”

section of this manual.

DUE TO HIGH TEMPERATURES THE APPLIANCE

SHOULD BE LOCATED OUT OF TRAFFIC AND

AWAY FROM FURNITURE, DRAPERIES,

CLOTHING AND FLAMMABLE MATERIALS. (EN

RAISON DES TEMPÉRATURES ÉLEVÉES,

L’APPAREIL DEVRAIT ÊTRE INSTALLÉ DANS UN

ENDROIT OÙ IL Y A PEU DE CIRCULATION ET

LOIN DU MOBILIER ET DES TENTURES.)

CHILDREN AND ADULTS SHOULD BE ALERTED

TO THE HAZARDS OF HIGH SURFACE

TEMPERATURES AND SHOULD STAY AWAY TO

AVOID BURNS TO SKIN OR CLOTHING IGNITION.

(LES ENFANTS ET LES ADULTES DEVRAIENT

ÊTRE INFORMÉS DES DANGERS QUE POSENT

LES TEMPÉRATURES DE SURFACE ÉLEVÉES ET

SE TENIR À DISTANCE AFIN D’ÉVITER DES

BRÛLURES OU QUE LEURS VÊTEMENTS NE

S’ENFLAMMENT.)

CAREFULLY SUPERVISE YOUNG CHILDREN

WHEN THEY ARE IN THE SAME ROOM AS THE

APPLIANCE. TODDLERS, YOUNG CHILDREN,

AND OTHERS MAY BE SUSCEPTIBLE TO

ACCIDENTAL CONTACT BURNS. A PHYSICAL

BARRIER IS RECOMMENDED IF THERE ARE AT

RISK INDIVIDUALS IN THE HOUSE. TO RESTRICT

ACCESS TO A FIREPLACE OR STOVE, INSTALL

AN ADJUSTABLE SAFETY GATE TO KEEP

TODDLERS, YOUNG CHILDREN, AND OTHER AT

RISK INDIVIDUALS OUT OF THE ROOM AND

AWAY FROM HOT SURFACES. (LES JEUNES

ENFANTS DEVRAIENT ÊTRE SURVEILLÉS

ÉTROITEMENT LORSQU’ILS SE TROUVENT

DANS LA MÊME PIÈCE QUE L’APPAREIL. LES

TOUT PETITS, LES JEUNES ENFANTS OU LES

ADULTES PEUVENT SUBIR DES BRÛLURES

S’ILS VIENNENT EN CONTACT AVEC LA

SURFACE CHAUDE. IL EST RECOMMANDÉ

D’INSTALLER UNE BARRIÈRE PHYSIQUE SI DES

PERSONNES À RISQUES HABITENT LA MAISON.

POUR EMPÊCHER L’ACCÈS À UN FOYER OU À

UN POÊLE, INSTALLEZ UNE BARRIÈRE DE

SÉCURITÉ; CETTE MESURE EMPÊCHERA LES

TOUT PETITS, LES JEUNES ENFANTS ET TOUTE

AUTRE PERSONNE À RISQUE D’AVOIR ACCÈS À

LA PIÈCE ET AUX SURFACES CHAUDES.)

CLOTHING OR OTHER FLAMMABLE MATERIAL

SHOULD NOT BE PLACED ON OR NEAR THE

APPLIANCE. (ON NE DEVRAIT PAS PLACER DE

VÊTEMENTS NI D’AUTRES MATIÈRES

INFLAMMABLES SUR L’APPAREIL NI À

PROXIMITÉ.)

CLEAN THE AREA AROUND, UNDER, AND

BEHIND THE UNIT ON A REGULAR BASIS TO

PREVENT THE ACCUMULATION OF DUST AND

LINT.

Ceramic Logs, & Burner

If the decorative ceramic log, or burner material

supplied with the DVI 44 are damaged or parts are

missing, they must be replaced with the same, or

approved Hearthstone replacement parts. These

components affect the combustion quality and safety

of the heater. Do not replace ceramic logs, or the

burner with unapproved ceramic components or any

other material.

We recommend you always wear gloves and safety

goggles while handling the ceramic log set, and

burner materials.

Electrical Hazard

Any three-prong grounded plug must be plugged

directly into a properly grounded three-prong

receptacle. Do not cut or remove the grounding

prong from any plug or otherwise attempt to

circumvent the grounding protection provided with

the unit. The DVI 44 must be electrically grounded in

accordance with local codes, or in the absence of

local codes, with the National Electrical Code,

ANSI.NFPA 70 in the U.S. or CSA C22.1 Canadian

Electrical Code in Canada.

Do Not Light Pilot or Burner by Hand

The pilot light on this gas heater is lit using an

electronic ignition module as described elsewhere in

this manual. Never attempt to light the pilot or main

burner by hand with a match or lighter.

Hearthstone Quality Home Heating Products, Inc. DVI-44 Model 8860

8

Mobile Home Installations

This appliance may be installed in an aftermarket

permanently located, manufactured (mobile) home

(USA only), where not prohibited by local codes.

(Cet appareil peut être installé dans un maison

préfabriquée (mobile) déjá installée á demeure si les

réglements locaux le permettent.

Hearthstone Quality Home Heating Products, Inc. DVI-44 Model 8860

9

Specifications

LISTED: Gas-Fired Direct-Vent Fireplace Heater

Model: DVI 44 Direct-Vent Gas Fireplace

Insert (8860)

Testing Agency: Intertek Testing Services

NA, Inc. (ITS)

Tested to: ANSI Z21.88-09, CSA 2.33-09,

CAN/CGA2.17-M91

Certified for Canada, CSA P.4.1-02

Approved for Mobile Home Installation (see

page 8)

Certified for use by:

Board of State Examiners of Plumbers & Gasfitters

100 Cambridge Street, Room 1511

Boston, MA 02202

www.mass.gov

Figure 1 - Model 8860 Dimensions (Inches)

Hearthstone Quality Home Heating Products, Inc. DVI-44 Model 8860

10

Figure 2 – 8860 Minimum Fireplace Dimensions

Specification

NG

LP

INPUT RATING (Btu/hr) (0-610 m)

43,000

46,000

MAXIMUM OUTPUT (Btu/hr) (0-610 m)

28,478

31,496

MINIMUM INPUT (Btu/hr) (0-610m)

15,000

17,000

HIGH ALTITUDE RATING (Btu/hr) 610-1370 m

36,000

37,000

ORIFICE SIZE (DMS) 0-610 m (front/rear))

46F/38R

55F/53R

MANIFOLD PRESSURE - (in. W.c./kpa)

3.5/0.87

10.0/2.48

MANIFOLD PRESSURE - Low setting (in. W.c./kpa)

1.6/0.40

6.4/1.59

INLET PRESSURE - MINIMUM (in.w.c./kpa)

5.0/1.25

12.0/2.99

INLET PRESSURE-MAX (in. W.c./kPa) 14.0/3.47

10.5/2.6

14.0/3.47

Hearthstone Quality Home Heating Products, Inc. DVI-44 Model 8860

11

NOTE: REMOVE FAÇADE & SURROUND FOR

COMPLETE ACCESS TO ELECTRICAL AND GAS

CONNECTIONS.

DVI 44 8860 Model Overview

Proflame 2 GTMFS System

The Proflame 2 GTMFS is a modular remote control

system that directs the functions of the DVI 44. The

Proflame 2 GTMFS System is configured to control

the on/off, main/split burner operation, its flame

levels, and provides Manual and Smart thermostatic

control of the hearth appliance. The system controls

two remotely actuated 120V/60Hz power outlets. The

Fan outlet controls the fan speed through six levels,

and the Auxiliary outlet, used for the firebox light,

either on or off. There is also an additional constantly

powered 120V/60Hz outlet. The system has battery

backup power for burner operation and control during

power outages (see page 13 for specifications).

Figure 3 – Proflame 2 Remote Transmitter

Remote Transmitter

The DVI 44 comes equipped with a thermostatic

remote control transmitter. The easy to read LCD

display shows all functional abilities as well as a

childproof lockout and low battery indicator. It

displays room temperature readout, set temperature

readout and function status. The remote transmitter is

powered by three 1.5 volt AAA batteries. A Mode Key

is provided to index between the features and a

Thermostat Key is used to turn on/off or index

through thermostat functions.

Figure 4 – Proflame 2 Battery Holder

Back-up Battery Holder- On/Remote/Off

Switch

The back-up battery holder is powered (6V DC) by

the Control Board and uses four 1.5 volt AA type

batteries for backup during power outages. The slider

switch is set to one of three positions: ON (Manual

Override), REMOTE (Remote Control) or OFF. The

ON selection turns the valve on (to high), and

activates the split flow setting last used if the Remote

becomes inoperative.

Figure 5 – Proflame 2 Control Board

Proflame 2 Control Board

This is the command center for the appliance. The

Control Board allows the pilot to run in the

Intermittent (IPI) mode or the Constant (CPI) mode.

The pilot mode can be toggled between IPI and CPI

via the remote control. The Control Board signals the

burner to light or shut down and provides the ignitor

with the electricity needed for sparking. It is the main

power supply for the entire system when 120V power

is available or by the batteries in the Back-up Battery

Holder during a power outage.

The Control Board provides 120V power to control

the fan unit through 6 speeds and turns the Accent

Hearthstone Quality Home Heating Products, Inc. DVI-44 Model 8860

12

Light on and off via the remote control. Neither the

Accent Light nor the blower will operate when 120V

power is not present.

The Control Board is equipped with a three-prong

(grounding) plug for protection against shock hazard

and should be plugged directly into a properly

grounded three-prong receptacle. Do not cut or

remove the grounding prong from the plug.

SIT Modulating Gas Valve

The remote transmitter can modulate the valve and

the flame to 6 different settings between high and off.

You can modulate the flame via the remote yourself

or by setting the remote control to one of the

thermostatic modes. In the thermostatic mode, the

stove will turn on/off based on the temperature set on

the remote. In the Smart thermostatic mode, as the

room temperature approaches the limit set for shut

down the valve will automatically gradually step down

the flame height. The reverse happens when the

room cools - the valve will automatically gradually

increase the flame height.

SIT Split Burner Solenoid

The remote transmitter can toggle between dual

burner, and single burner mode (46,000 Btu/hr (LP)

43,000 (NG) or 16,000 Btu/hr). The burner will turn

on/off.

Pilot Assembly

The pilot assembly consists of a pilot hood, sensor

rod, and ignitor. The ignitor sends a spark to the pilot

hood which ignites the gas and lights the pilot. With

the pilot lit the sensor rod is engulfed by the flame,

flame rectification occurs and the appliance remains

lit. If the sensor does not stay engulfed by the flame

the main burner will not light and the pilot will shut

down.

Hearthstone Quality Home Heating Products, Inc. DVI-44 Model 8860

13

Figure 6 - Proflame GTMFS Component Specifications

Hearthstone Quality Home Heating Products, Inc. DVI-44 Model 8860

14

Control Functions

Pilot Mode

Continuous Pilot (CPI): Running the DVI 44 in CPI mode will keep your pilot on even when the thermostat

does not call for heat and when the burner is not lit. This is an advantage in cooler temperatures or under windy

conditions. The “standing pilot” helps to keep the venting warm and generate some draft within the system. The

standing pilot also keeps the firebox and venting warm – greatly minimizing, draft issues or condensation

formation on the glass during startup. The ignitor will automatically spark whenever the pilot mode is switched to

CPI, regardless of the position of the receiver switch. Hearthstone recommends the use of the CPI mode during

the heating season.

Intermittent Pilot (IPI): Using the IPI mode is a more efficient use of fuel as the pilot only ignites when the

thermostat calls for heat.

To switch back and forth between the two pilot modes 1) Press the OFF button on the remote 2) Press the

Mode button on the remote. 3) Press Up or Down on the center pad to toggle back and forth between the two

modes.

Back –up Battery Holder- On/Remote/Off Switch

The Back-up Battery Holder is normally powered by the Proflame 2 Control Board or by four 1.5V AA batteries

during a power outage. This On/Remote/Off switch can be set to three different positions:

On: Manual override allowing the valve to function and ignite the burner without the remote transmitter. The

ignitor will spark automatically.

Remote: Remote Transmitter controls all functions of components.

Off: Turns off the stove. If CPI mode is selected, pilot will remain lit.

PRG Key: Used to synchronize the Transmitter and Receiver initially, and after each battery change (see page

38).

Figure 7 - Receiver Detail

Hearthstone Quality Home Heating Products, Inc. DVI-44 Model 8860

15

Remote Transmitter

Figure 8 - Remote Transmitter Function Keys (remote color may differ from shown)

ON/OFF Key: Controls the insert.

Thermostat Key: This is the function that sets either

the Manual or Smart thermostatic control.

UP/Down Arrow Key: Adjusts the thermostat

temperature range, flame settings, split flow, and fan

speed.

Mode Key: Toggles through the component to be

controlled (split flow burner, blower or auxiliary

outlet)

The transmitter features a user-friendly layout with a

Blue LCD Screen for easier viewing.

See the instructions provided with the remote for

more operation details.

Figure 9 - Remote Transmitter Display Data

Hearthstone Quality Home Heating Products, Inc. DVI-44 Model 8860

16

Installation Preparation

Codes

Adhere to all local codes or, in their absence, the

latest edition of THE NATIONAL FUEL GAS CODE

ANSI Z223.1 (NFPA 54) or CAN/CGA B149 (Installer

l’appareil selon les codes ou règlements locaux, ou,

en l’absence de tels règlements, selon les Codes

d’installation CAN/CGA-B149.)

Installation Codes can be obtained from:

AMERICAN NATIONAL STANDARDS

INSTITUTE, INC.

1430 BROADWAY

NEW YORK, NY 10018

www.ansi.org

NATIONAL FIRE PROTECTION ASSOCIATION,

INC.

BATTERY MARCH PARK

QUINCY, MA 02269

www.nfpa.org

When installed, the appliance must be electrically

connected and grounded in accordance with local

codes or, in the absence of local codes, with the

current NFPA 70-National Electrical Code or CSA

C22.1-Canadian Electric Code.

A manufactured home (mobile) OEM installation must

conform to the Manufactured Home Construction and

Safety Standard, Title 24 CFR, Part 3280 (U.S.) or

Standard for Manufactured Home Installation,

ANSI/NCBCS A225.1 or Standard for Gas Equipped

Recreational Vehicles and mobile Housing, CSA

Z240.4.CAN/SCA Z240 MH (Canada). (Installer

l’appareil selon les codes ou règlements locaux, ou,

en l’absence de tels règlements, selon les Codes

d’installation CAN/CGA-B149.)

This appliance is equipped for use at 0 to 2000 feet

(0-610 meters) altitude (refer to page 28). (Cet

appareil est equipè pour des altitudes compries entre

0 et 2000 pieds (0-610 m) seulement.)

WARNING: DO NOT INSTALL OR USE THIS

APPLIANCE IF ANY PART WAS SUBMERGED

UNDER WATER. IMMEDIATELY CALL A

QUALIFIED SERVICE TECHNICIAN TO INSPECT

THE HEATER AND TO REPLACE ANY PART OF

THE CONTROL SYSTEM AND GAS CONTROL

THAT WAS UNDER WATER. (NE PAS SE SERVIR

DE CET APPAREIL S’IL A ÉTÉ PLONGÉ DANS

L’EAU, COMPLÈTEMENT OU EN PARTIE.

APPELER UN TECHNICIEN QUALIFIÉ POUR

INSPECTOR L’APPAREIL ET REMPLACER TOUTE

PARTIE DU SYSTÈME DE CONTRÔLE ET TOUTE

COMMANDE QUI ONT ÉTÉ PLONGÉS DANS

L’LAU)

Items Required for Installation

Approved venting

External regulator (for propane (LP) only)

LP conversion kit, for propane only (not

included).

Piping which complies with local codes

Pipe sealant approved for use with

propane (LP) (resistant to sulfur compounds).

Sediment trap (see page 27)

120 volt, 15 Amp electrical service

Pipe wrench

Phillips head screwdriver

7/16-inch wrench

¼-inch wrench

Other parts as required by local code

Safety Glasses

Gloves

Packing List

1- DVI 44 8860 Gas-Fired Insert

1- Owner’s Packet Envelope (manual, warranty,

warranty card, Fireplace Warning Label, Flue

Tool)

4- Decorative Ceramic Logs (in box in firebox)

1- Safety Screen (on firebox)

1- Surround Assembly (box on pallet if applicable)

1- Façade Assembly (box on pallet if applicable)

1- Ceramic Baffle Set (box on Shipping Carton)

1- Accessory Packet (on pallet) containing:

1- Remote Control

1- Package of four AA Batteries

1- Package of three AAA Batteries

1- Bag of Platinum Bright Embers

1- Baffle Touch-up Paint

Note: Vent kits and components are supplied

separately. Failure to use the venting

components approved by Hearthstone for this

appliance will void your warranty.

Unpacking and Inspection

Hearthstone packages your DVI 44 to withstand

normal shipment without damage. However, damage

can still occur during transit. Take care to inspect for

damage when unpacking and installing the unit.

DO NOT INSTALL, OR PUT INTO SERVICE, A

DAMAGED OR INCOMPLETE HEATER.

Remove the shrink-wrap and all other packaging

materials taking care not to damage the stove’s

finish. Inspect the DVI 44 for visible or concealed

Hearthstone Quality Home Heating Products, Inc. DVI-44 Model 8860

17

damage. The unit should be square and true. Any

sheet metal parts should be smooth and free of

bends and dents. If visible or concealed damage is

found or suspected, contact your dealer for

instructions.

Always use gloves and eye protection when handling

the decorative ceramic fire logs, and burner. Use

care when handling these parts as they are fragile

and subject to damage and breakage if handled

roughly.

See the firebox access instructions on page 188 and

remove the log set. Unpack and inspect the logs for

damage. Inspect the ceramic burner. Open the other

boxes and inspect the components. If log, burner, or

any other component damage is encountered,

contact your dealer for a replacement. Otherwise, set

the logs and other components aside until called for

during the installation.

Dismounting from Pallet

With all accessory boxes removed and set aside,

remove the shipping carton, then remove the 4 lag

screws and shipping clips that fasten the unit to the

pallet.

Have someone help lift the insert up and off the

pallet, taking care to avoid damaging components

mounted on the insert.

Figure 10 – Shipping Clip Detail

Figure 11 – Leveling Bolt Detail

Leveling Screws

If your hearth/fireplace surface in uneven, or is not

level, you can adjust the four provided leveling

screws. Adjust the screws using a ¼” wrench only

enough to keep the insert from rocking, or wobbling.

INSTALLER: Leave

this manual with the

appliance.

CONSUMER: Retain

this manual for future

reference.

«INSTALLATEUR :

Laissez cette notice avec

l’appareil.

CONSOMMATEUR :

Conservez cette notice

pour consultation

ultérieure.»

Hearthstone Quality Home Heating Products, Inc. DVI-44 Model 8860

18

Firebox Access

1. If installed, remove the Façade.

2. Remove the front screen by lifting it up and off

the glass frame – pulling it from behind the lower

glass retainer. Remove all packaging material

from the screen (if applicable).

3. Pull outward and then upward on the spring

loaded clips; rotate the clips to a generally

horizontal position. Tilt the top of the front panel

slightly outward to clear the tangs at its top.

Figure 12 – Glass Frame Upper Mounting Detail

Figure 13 – Rotate Spring Clips

Figure 14 –Glass Frame Lower Mounting Detail

4. Lift the glass frame up out of the lower retainer

and set aside on a soft surface.

Figure 15 – Tilt and Lift Glass Frame

1. See page 29 for log set installation instructions.

Reinstall components by reversing the previous

steps. Ensure you slide the lower glass frame

tangs behind the spring keepers. When

reinstalling the screen, ensure you insert the

bottom edge behind the lower glass retainer.

Hearthstone Quality Home Heating Products, Inc. DVI-44 Model 8860

19

Clearances to Combustibles

Note: Ensure clearances are in accordance

with local installation codes and the

requirements of the gas supplier.

Clearance to Combustibles

Due to high surface temperatures, locate the unit out

of traffic areas and away from furniture and

draperies. Do not place clothing and other

flammable material on or near the heater. When

positioning the unit always maintain adequate

clearances around air openings into the combustion

chamber and allow for adequate ventilation and

servicing. Minimum clearances to combustibles must

be maintained as shown in the following figures.

Ensure you consider the need for access to the gas

control valve, gas piping, as well as full access for

periodic cleaning and servicing.

CAUTION: THESE CLEARANCES REPRESENT

MINIMUM DISTANCES IN ALL CASES, WHICH,

THROUGH TESTING IN AN INDEPENDENT

LABORATORY TO ANSI AND CSA STANDARDS,

WILL PREVENT FIRE OR SPONTANEOUS

COMBUSTION. WE DO NOT CONTROL THE

COMBUSTIBLE MATERIALS EXPOSED TO HEAT

BY THIS PRODUCT; THEREFORE, AN

ASSESSMENT MUST BE MADE BY THE

INSTALLER TO PREVENT CONSEQUENTIAL

DAMAGE OF WALLS AND FLOORING.

Hearth Requirement/Floor

Protection

The DVI 44 requires a non-combustible hearth, or

hearth pad that extends no less than 16” in front of

the unit. Installations must meet all local codes.

Figure 16 - Minimum Side Trim Clearances

Figure 17 - Mantle Clearances

Ensure the masonry fireplace and flue complies

with the applicable codes and both are clean and in

good condition. The Fireplace chimney must be

constructed of non-combustible materials. Repair

any damage before installation of the DVI-38 begins.

Prepare a zero clearance (metal) fireplace by

doing the following:

1. Install the label provided on the inside of the

firebox.

2. Remove the grate and block open the

damper.

3. If necessary, remove the smoke shelf,

internal baffles, refractory, log grates,

screen, masonry lining and glass doors.

(These components may be removed if they

are attached with mechanical fasteners.)

4. DO NOT cut, or remove any insulation, or

structural frame members.

5. DO NOT remove, or alter the metal sides,

floor, door frame, or face of the fireplace.

6. Ensure the chimney cleanout(s) fit and seal

properly.

Hearthstone Quality Home Heating Products, Inc. DVI-44 Model 8860

20

If the factory-built fireplace has no gas access

hole(s) provided, drill an access hole 1.5” in

diameter or less through the lower sides or bottom of

the metal zero clearance firebox in a proper

workmanship like manner. Remove sharp edges to

avoid damaging the gas line. This access hole must

be sealed with non-combustible insulation after the

gas supply line is installed. (Si le foyer préfabriqué

ne comporte pas d’orifices d’amenée du gaz, un

orifice d’au plus 37,5 mm (1,5 po) peut être pratiqué,

selon les règles de l’art, dans la partie inférieure des

parois ou au fond de la chambre de combustion. Cet

orifice doit être obturé au moyen d’isolant

incombustible une fois la conduite de gaz en place.)

Trim panels and surrounds shall not seal ventilation

openings in the fireplace. The minimum size

fireplace the DVI 44 insert will fit into is 35” W x 24-

1/2” H x 18-1/2” D.

Installation of the Co-linear Vent Pipe

Mark each end of one of the flexible vent pipes

“intake” with a permanent marker. Mark each end of

the other flexible vent pipe “exhaust”.

Apply the high temperature silicone on the upper

portion of the vent (flex pipes to co-linear to co-

axial adaptor). Important: Ensure the pipe

connected to the exhaust on the stove connects

to the exhaust portion of the co-linear to co-axial

adaptor. Ensure you meet all the vent pipe

manufacturer’s requirements when installing the

adaptor and cap assembly. Follow the

manufacturer’s instructions when installing the

same. (The exhaust pipe on the co-linear to co-

axial adaptor is the pipe that is in the center of

the adaptor.)

Repeat this process to the top outer edge of

both the intake and exhaust collars on the top of

the unit. The exhaust port is on the right, the

intake port on the left, when viewed from the

front. Slide a hose clamp over the ends of both

flexible vent pipes. Place the flexible vent pipe

marked “intake” onto the intake port’s collar,

place the flexible vent pipe marked “exhaust”

onto the exhaust port’s collar. Secure the pipes

to the collars by tightening the hose clamps with

a slotted screwdriver or 5/16" nut driver.

Observe the following guidelines when installing the

vent pipes:

Do not install the venting into a chimney serving

another appliance, be it fossil fuel, solid fuel, or

another gas.

Do not crimp or rupture the vent pipes.

Installing the flue vent plate using the

Installation Tool

1. You will need to remove the Flue Vent Plate

from the stove before you place the insert into

the fireplace.

2. Locate the Flue Vent Plate on the top of the

insert.

3. Using a Phillips head screwdriver, remove the

screw holding the front of the Flue Vent Plate to

the firebox. Push the plate carefully back and

out of the retaining tracks – take it off the stove

as shown (see Figures 18 &19). Keep this

screw, as you will need it later to remount the

plate.

Figure 18

4. Attach the 4” Exhaust flex pipe to the RIGHT

side of the Flue Vent Plate. (facing the front of

the stove) Attach the 3” Inlet flex pipe to the Left

side of the Flue Vent Plate.

5. Carefully position the DVI 44 in front of the

fireplace opening. Slowly slide the insert back so

the rear of the insert is just inside the fireplace.

Start the Flue Vent Plate underneath the

Retaining Tracks on the top of the insert. (See

Figure 19) The Retaining Tracks will ensure a

tight seal for the flue gases when the plate is

fully seated.

6. Locate the Installation Tool. Slide the end of the

tool with the threads though the Mounting Point

hole on the firebox bracket.

7. Thread the Installation Tool into the front of the

Flue Vent Plate.

Mounting Point for

5/32 screw and

Installation Tool.

Flue Vent

Plate

Mounting

Point for

screw and

Installation

Tool.

3”Intake

4”Exhaust

La page est en cours de chargement...

HearthStone DVI 44 Manuel utilisateur

Ce manuel convient également à

HearthStone DVI 44 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents