Samsung PS-58P96FDR Manuel utilisateur

Register your product at www.samsung.com/global/register

Record your Model and Serial number here for future reference.

▪ Model _______________ ▪ Serial No. _______________

PDP-TELEVISION

(PLASMA DISPLAY PANEL)

PS-50P96FDR

PS-58P96FDR

PS-63P76FDR

Owner’s Instructions

Before operating the unit,

please read this manual thoroughly,

and retain it for future reference.

ON-SCREEN MENUS

Picture In Picture (PIP)

Energy Saving

TELETEXT (Option)

SRS TruSurround XT

Digital Natural Image engine

BN68-01352E-01

Contact SAMSUNG WORLD-WIDE

If you have any questions or comments relating to Samsung products, please contact the

SAMSUNG customer care centre.

Связывайтесь с SAMSUNG по всему миру

Если у вас есть предложения или вопросы по продуктам Samsung, связывайтесь с

информационным центром Samsung.

Country

Customer Care Centre 

Web Site

RUSSIA 8-800-200-0400 www.samsung.ru

UKRAINE 8-800-502-0000 www.samsung.com/ur

BN68-01352E-00_CIS(BWT)_E,R_Cover.indd 1 2007-10-05 ¿ÀÈÄ 5:38:36

English - 2

User Instructions

 Screen Image retention

Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the

plasma monitor panel for more than 2 hours as it can cause screen image retention. This image

retention is also known as “screen burn”. To avoid such image retention, reduce the degree of

brightness and contrast of the screen when displaying a still image.

 Height

The PDP can normally operate only under 2000m in height. It might abnormally function at a place

over 2000m in height so do not install and operate there.

 Heat on the top of the PDP TV

The top side of the product may be hot after long period of use as heat dissipates from the panel

through the vent hole in the upper part of the product. This is normal and does not indicate any defect

or operation failure of the product. However, children should be prevented from touching the upper

part of the product.

 The product is making a ‘cracking’ noise.

A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding

environment such as temperature or humidity. This is normal and not a defect of the unit.

 Cell Defects

The PDP uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require

sophisticated technology to produce. However, there may be few bright or dark pixels on the screen.

These pixels will have no impact on the performance of the product.

 Avoid operating the TV at temperatures below 5°C(41°F)

 A still image displayed too long may cause permanent damage to the PDP Panel.

Watching the PDP TV in 4:3 format for a long period of time may leave traces

of borders displayed on the left, right and centre of the screen caused by the

difference of light emission on the screen. Playing a DVD or a game console

may cause similar effect to the screen. Damages caused by the above effect are

not covered by the Warranty.

 Afterimage on the Screen.

Displaying still images from Video games and PC for longer than a certain period of time may

produce partial afterimages. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when

displaying still images.

 Warranty

- Warranty does not cover any damage caused by image retention.

- Burn-in is not covered by the warranty.

 Installation

Be sure to contact an authorized service centre, when installing your set in a location with heavy

dust, high or low temperatures, high humidity, chemical substance and where it operates continually

such as the airport, the train station etc. Failure to do so may cause a serious damage to your set.

Any functions related to Digital TV (DVB) will only work in countries or areas where DVB-T (MPEG2)

digital terrestrial signals are broadcasted. Please confirm with your local dealer if you can receive

DVB-T signals. Although this TV set follows the DVB-T specification, maintaining compatibility with

the future coming DVB-T digital terrestrial broadcasts is not guaranteed. Several functions may not be

available in some countries.

BN68-01352E.F-00Eng(CIS).indd 2 2007-10-05 ¿ÀÈÄ 1:52:02

English - 3

Symbols

☛ ➢

Press

Important

Note

Contents

General Information

 User Instructions ............................................. 2

 Checking Parts ................................................ 4

 Using the Stand-Base ..................................... 4

 Control Panel ................................................. 5

 Connection Panel ............................................ 6

 Viewing the Remote Control .......................... 8

Operation

 Switching Your Television On and Off ............. 9

 Viewing the Menus ........................................ 10

 Plug & Play Feature ...................................... 10

 Viewing External Signal Sources .................. 12

 Editing Device Names ................................... 13

Channel Control

 Storing Channels Automatically .................... 13

 Storing Channels Manually ........................... 14

 Adding / Locking Channels ........................... 15

 Sorting the Stored Channels ......................... 16

 Assigning Names to Channels ...................... 16

 Fine Tuning Channel Reception .................... 17

 LNA (Low Noise Ampliﬁer) ............................ 17

Picture Control

 Changing the Picture Standard ..................... 18

 Customizing the Picture Settings .................. 18



Conﬁguring Detailed Settings on the Picture

.. 19

 Selecting the Picture Size ............................. 20

 Selecting the Screen Mode ........................... 20



Digital NR / Active Colour / DNIe / Movie Plus

.. 21

 Freezing the Current Picture ......................... 21

Sound Control

 Sound Features ............................................ 22

 Selecting the Sound Mode (depending on

the model) ..................................................... 23

Function Description

 Time Features ............................................... 24

 Language / Blue Screen / Melody /

Light Effect / Energy Saving /

HDMI Black Level ......................................... 25

 Using the Game Mode .................................. 26

 Wall- mount adjustment (Sold separately)

(PS-50P96FDR) ............................................ 27

 Viewing the Picture in Picture (PIP) .............. 28

 Screen Burn Protection ................................. 29

PC Display

 Setting up Your PC Software (Based on

Windows XP) ................................................ 30

 Display Modes .............................................. 31

 Setting the PC ............................................... 32

 Setting the Home Theatre PC ....................... 33

Using the DTV Feature

 Previewing the DTV Menu System ............... 34

 Displaying Programme Information ............... 35

 Operating the DTV Menu .............................. 36

About Anynet

+

 What is Anynet

+

? ........................................ 46

 Connecting Anynet

+

Devices ........................ 46

 Setting Up Anynet

+

....................................... 47

 Scanning and Switching between Anynet

+

Devices ......................................................... 47

 Recording ...................................................... 48

 Listening through a Receiver ........................ 49

 Check Points before Requesting Service ..... 49

Appendix

 Teletext Feature (depending on the model) .. 50

 Wall Mount Kit Speciﬁcations (VESA) ........... 52

 Setting Up Your Remote Control ................... 53

 How to assemble the Stand-Base

(depending on the model) ............................. 58

 Troubleshooting ............................................ 58

 Speciﬁcations ................................................ 59

BN68-01352E.F-00Eng(CIS).indd 3 2007-10-05 ¿ÀÈÄ 1:52:02

English - 4

Checking Parts

Owner’s Instructions Remote Control/

AAA Batteries

Power Cord Cloth-Clean Warranty Card/

Registration Card/

Safety Guide Manual

Cover-Bottom / Screws (2ea)

(PS-50P96FDR/PS-58P96FDR,

Refer to page 58)

Ferrite Core

Sold Separately

S-Video Cable Antenna Cable Component Cables Audio Cables Video Cable

PC Cable Scart Cable PC Audio Cable HDMI Cable HDMI/DVI Cable

➢

Ferrite Core

The ferrite cores are used to shield the cables

from interference.

When connecting a cable, open the ferrite

core and clip it around the cable near the

plug.

➢

Turn the ferrite core around the part of the DVI

cable close to the PC when the HDMI2 port

and the PC are connected with the HDMI/DVI

cable. (PS-58P96FDR)

Using the Stand-Base

➢



Two or more people should carry

the PDP. Never lay the PDP on the

floor because of possible damage

to the screen. Always keep the

PDP upright.



The PDP can rotate 20 degrees in

right and left directions.

-20° ~ 20°

Side Panel Jack

or

Power Cord

HDMI/DVI

Cable

Headphones

Cable

Audio Cables/

Video Cable

Audio Cables/

S-Video Cable

BN68-01352E.F-00Eng(CIS).indd 4 2007-10-05 ¿ÀÈÄ 1:52:07

English - 5

Control Panel

1

SOURCE

Displays a menu of all of the available input

sources (TV, Ext.1, Ext.2, AV, S-Video,

Component, PC, HDMI1, HDMI2, HDMI3, and

DTV).

➢

In the on-screen menu, use this button as

you would use the ENTER/OK button on

the remote control.

(PS-50P96FDR/PS-58P96FDR)

2

MENU

Press to see the on-screen menu of your TV’s

features.

3

+



−

Press to increase or decrease the volume.

In the on-screen menu, use the +



−

buttons as you use the ◄ and ► buttons on

the remote control.

4

C/P.

Press to change channels. In the on-screen

menu, use the C/P. buttons as

you use the ▲ and ▼ buttons on the remote

control.

5

(ENTER/OK)

Press to confirm a selection.

6

(Power) button

Press to turn the TV on and off.

Power Indicator

Blinks and turns off when the power is on and

lights up in stand-by mode.

Remote Control Sensor

Aim the remote control towards this spot on

the TV.

7

Speaker

➢

The product colour and shape may vary depending on the model.

Front (or Side) Panel

PS-50P96FDR/PS-58P96FDR

PS-63P76FDR

BN68-01352E.F-00Eng(CIS).indd 5 2007-10-05 ¿ÀÈÄ 1:52:16

English - 6

Connection Panel

1

HDMI IN 3

Connect to the HDMI jack of a device with

HDMI output.

2

S-VIDEO or VIDEO / AUDIO L/R

Video (S-Video or Video) and audio inputs for

external devices, such as a camcorder or VCR.

3

Headphones jack

You can connect a set of headphones if you

wish to watch a television programme without

disturbing the other people in the room.

➢

Prolonged use of headphones at a high

volume may damage your hearing.

Continued...

☛



Whenever you connect an audio or video system to your set, ensure that all elements are

switched off.



When connecting an external device, match the colour of the connection terminal to the cable.

➢

The product colour and shape may vary depending on the model.

➢

The product colour and shape may vary depending on the model.

(PS-58P96FDR)

Side Panel

3

or

1

Rear Panel

1

3

7

4

2

Cable Television

Network

0

6

9

or

5

8

2

8

BN68-01352E.F-00Eng(CIS).indd 6 2007-10-05 ¿ÀÈÄ 1:52:22

English - 7

1

POWER IN

Connect the supplied power cord.

2

Connecting external Audio Devices

Connect RCA audio signals from the TV to an

external source, such as Audio equipment.

3

EXT 1, EXT 2

Inputs or outputs for external devices, such as

VCR, DVD, video game device or video disc

players.

Input/Output Specification

Connector

Input Output

Video Audio(L/R) RGB Video + Audio(L/R)

EXT 1

✔ ✔ ✔

Only TV or DTV

output is available.

EXT 2

✔ ✔

Output you can

choose.

4

COMPONENT IN

Audio (AUDIO L/R) and video (Y/PB/PR) inputs

for Component.

5

DIGITAL AUDIO OUT (OPTICAL)

Connect to a Digital Audio Component.

6

SERVICE

− Connector for service.

− Connect the serial jack between the

electro-motion wall mount bracket and your

TV when you want to adjust the TV viewing

angle using your remote control.

7

PC IN / AUDIO

Connect to the video and audio output jack on

your PC.

8

COMMON INTERFACE Slot

Insert CI (Common Interface) card into the slot.

(refer to page 45)

− When not inserting “CI CARD” in some

channels, “Scramble Signal” is displayed on

the screen.

− The pairing information containing a

telephone number, CI CARD ID, Host ID,

and other information will be displayed in

about 2~3 minutes. If an error message

is displayed, please contact your service

provider.

− When the channel information configuration

has finished, the message “Updating

Completed” is displayed, indicating that the

channel list is now updated.

➢

Insert the CI-Card in the direction marked

on it.

9

HDMI IN 1, HDMI IN 2

− Connect to the HDMI jack of a device with

HDMI output. These inputs can also be used

as a DVI connection with separate analog

audio inputs. An optional HDMI/DVI cable

will be necessary to make this connection.

When using the optional HDMI/DVI adapter,

the DVI analog audio inputs on your TV

allow you to receive left and right audio from

your DVI device. (Not compatible with PC)

− When connecting this product via HDMI or

DVI to a Set Top Box, DVD Player or Games

Console etc, make sure that it has been

set to a compatible video output mode as

shown in the table below. Failure to observe

this may result in picture distortion, image

breakup or no picture.

− Do not attempt to connect the HDMI/DVI

connector to a PC or Laptop Graphics Card.

(This will result in a blank screen being

displayed)

− The TV may not output sound and pictures

may be displayed with abnormal color

when DVD players/Cable Boxes/Satellite

receivers supporting HDMI versions older

than 1.3 are connected. When connecting

an older HDMI cable and there is no sound,

connect the HDMI cable to the HDMI IN

2 jack and the audio cables to the DVI IN

(HDMI2) [R-AUDIO-L] jacks on the back of

the TV. If this happens, contact the company

that provides the external device to confirm

the HDMI version, then request an upgrade.

DVI IN (HDMI 2) AUDIO L/R

DVI audio outputs for external devices.

0

ANT IN

75Ω Coaxial connector for Aerial/Cable

Network.

Supported modes for HDMI and Component

480i 480p 576i 576p 720p 1080i 1080p

HDMI/DVI 50Hz X X X O O O O

HDMI/DVI 60Hz X O X X O O O

Component O O O O O O X

BN68-01352E.F-00Eng(CIS).indd 7 2007-10-05 ¿ÀÈÄ 2:58:08

English - 8

Viewing the Remote Control

➢



This is a special remote control for the visually impaired persons, and has Braille points on the

Power, Channel, Volume, STOP, and PLAY/PAUSE buttons.



The performance of the remote control may be affected by bright light.

1

POWER button

(turns the TV on and off)

2

Number buttons for direct

channel access

3

One/Two-digit channel

selection

4

Channel control button

(Refer to page 15)

5

Selects the TV and DTV

mode directly

6

Volume increase

Volume decrease

7

Temporary sound switch-off

8

Displays the main on-screen

menu

9

Returns to the previous

menu

@

Picture size selection

#

Electronic Program Guide

(EPG) display

$

Sound mode selection

%

Remote control setup

^

Selects a target device to be

controlled by the Samsung

remote control (TV, DVD,

STB, CABLE, VCR)

&

Press to backlight the VOL,

CH, and the active source

button (TV, DVD, CABLE,

STB, VCR) on the remote.

*

Available source selection

(

Previous channel

)

DTV menu display

a

Records for Live

Broadcasting

b

VCR/DVD Function (Rewind,

Stop, Play/Pause, Fast/

Forward)

c

Next channel

Previous channel

d

Exit the on-screen menu

e

Control the cursor in the

menu

f

Use to see information on

the current broadcast

g

Runs the Anynet

+

view

functions and sets up

Anynet

+

devices.

h

Picture-In-Picture On/Off

i

Picture effect selection

(Refer to page 18)

j

Digital subtitle display

k

Picture freeze

l

If your remote control is not

functioning properly, take out

the batteries and press the

reset button for about 2~3

seconds.

Reinsert the batteries and

try using the remote control

again.

Teletext Functions

(Refer to page 50)

5

Exit from the teletext display

(depending on the model)

8

Teletext index

0

Fastext topic selection

!

Teletext display/mix both

teletext information and the

normal broadcast

@

Teletext size

*

Teletext mode selection

(LIST/FLOF)

(

Teletext sub page

c

P :Teletext next page

P :Teletext previous page

d

Teletext cancel

f

Teletext reveal

h

Teletext hold

i

Teletext store

Continued...

BN68-01352E.F-00Eng(CIS).indd 8 2007-10-05 ¿ÀÈÄ 1:52:30

English - 9

Installing Batteries in the Remote Control

1 Lift the cover at the back of the remote control upward as

shown in the figure.

2 Install two AAA size batteries.

➢

 Make sure to match the “+” and “–” ends of the

batteries with the diagram inside the compartment.

 Do not mix battery types, i.e. alkaline and manganese.

3 Close the cover as shown in the figure.

➢

Remove the batteries and store them in a cool and dry

place if you won’t be using the remote control for a long

time. The remote control can be used up to about 23 feet

from the TV. (Assuming typical TV usage, the batteries last

for about one year.)

➢

If the remote control doesn’t work! Check the following:

1. Is the TV power on?

2. Are the plus and minus ends of the batteries reversed?

3. Are the batteries drained?

4. Is there a power cut, or is the power cord unplugged?

5. Is there a special fluorescent light or a neon sign nearby?

Switching Your Television On and Off

The main lead is attached to the rear of the television.

1 Plug the main lead into an appropriate socket.

➢

The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz.

2 Press the (Power) button (On/Off) on the front of the television or press the POWER button on the

remote control to switch the television on. The programme that you were watching last is reselected

automatically. If you have not yet stored any channels, no clear picture appears. Refer to “Storing

Channels Automatically” on page 13 or “Storing Channels Manually” on page 14.

➢

If the television is initially powered on, several basic customer settings proceed automatically.

Refer to “Plug & Play Feature” on page 10.

3 To switch the television off, press the (Power) button (On/Off) on the front of the television or press

the POWER button on the remote control.

4 To switch the TV on, press the (Power) button (On/Off) on the front of the TV or press the POWER

button or number buttons on the remote control.

BN68-01352E.F-00Eng(CIS).indd 9 2007-10-05 ¿ÀÈÄ 1:52:36

English - 10

Viewing the Menus

1 Press the MENU button.

The main menu is displayed on the screen.

Its left side has five icons: Picture, Sound, Channel, Setup,

and Input.

2 Press the ▲ or ▼ button to select one of the icons.

Press the ENTER/OK button to access the icon’s sub-menu.

3 Press the ▲ or ▼ button to move to items in the menu.

Press the ENTER/OK button to enter items in the menu.

4 Press the ▲/▼/◄/► button to change the selected items.

Press the RETURN button to return to the previous menu.

5 Press the EXIT button to exit from the menu.

Plug & Play Feature

When the television is initially powered on, several basic

customer settings proceed automatically and subsequently.

The following settings are available.

☛

If you accidentally select the wrong country for your TV, the

characters on the screen may be wrongly displayed.

☛

Any functions related to Digital TV (DVB) will only work in

countries or areas where DVB-T (MPEG2) digital terrestrial

signals are broadcasted. Please confirm with your local dealer if

you can receive DVB-T signals. Although this TV set follows the

DVB-T specification, maintaining compatibility with the future

coming DVB-T digital terrestrial broadcasts is not guaranteed.

Several functions may not be available in some countries.

1 If the television is in standby mode, press the POWER button

on the remote control. The message Start Plug & Play is

displayed. Press the ENTER/OK button.

2 The Language menu will automatically appear after several

seconds.

3 Select the appropriate language by pressing the ▲ or ▼ button.

Press the ENTER/OK button. The message Select Home

Mode when installing this TV at home. is displayed.

4 Press the ◄ or ► button to select Shop or Home, then press

the ENTER/OK button. The message to check the connected

status of the antenna is displayed.

➢

The default selection is Home.

➢

We recommend setting the TV to Home mode for the best

picture in your home environment.

➢

Shop mode is only intended for use in retail environments.

➢

If the unit is accidentally set to Shop mode, and you want to

return to Dynamic (Home) mode, press the Volume button

and then hold down the MENU button for five seconds on

the TV panel.

5 Make sure that the antenna is connected to the TV.

Press the ENTER/OK button. The Country menu is displayed.

Continued...

Move

Enter

Exit

Mode :

Dynamic 

Contrast 100

Brightness 45

Sharpness 75

Colour 55

Tint G 50 R 50

Colour Tone :

Cool1 

Detailed Settings



 More

Picture

T V

Plug & Play

Start Plug & Play.

OK

Enter

Exit

Plug & Play

Language

Move

Enter

Skip

English

Deutsch

Français

Italiano

▼

Plug & Play

Select Home Mode

When installing this TV at home.

Move

Enter

Skip

Shop

Home

Plug & Play

Country

Move

Enter

Skip

▲

United Kingdom

Austria

Eastern Europe

▼

Plug & Play

Check antenna input.

Enter

Skip

OK

BN68-01352E.F-00Eng(CIS).indd 10 2007-10-05 ¿ÀÈÄ 1:52:38

English - 11

6 Select your country or area by pressing the ▲ or ▼ button.

Press the ENTER/OK button.

The message Some DTV functions may not be available.

Digitally Scan? is displayed.

➢

This function is supported for all countries except for the

following 6 countries: the United Kingdom, Austria, France,

Germany, Italy, Spain.

If your country supports the DTV functions, the message is

not displayed. Then you can follow the instructions from step

12. When the local service provider does not support DTV

broadcasting but you choose a DTV supporting country, it

enters the DTV Plug & Play but DTV functions may not work

properly.When

No is selected, follow the instructions from step

7 to 10. When Yes is selected, follow the instructions from

step 11.

7 Select No pressing the ◄ or ► button, then press the ENTER/

OK button. Auto Store menu is displayed.

8 Press the ENTER/OK button to start search the channels. The

channel search will start and end automatically. After all the

available channels are stored, Clock Set menu is automatically

displayed. Press the ENTER/OK button.

➢

To stop the search before it has finished, press the

ENTER/OK button with Stop selected.

9 Press the ◄ or ► button to select Month, Day, Year, Hour, or

Minute. Set these by pressing the ▲ or ▼ button.

➢

You can set the Month, Day, Year, Hour, or Minute

directly by pressing the numeric buttons on the remote

control.

10 Press the ENTER/OK button to confirm your setting. The

message Enjoy your viewing is displayed. When you have

finished, press the ENTER/OK button.

➢

Even if the ENTER/OK button is not pressed, the message

will automatically disappear after several seconds.

11 Select Yes

pressing the ◄ or ► button, then press the

ENTER/OK button. Auto Store menu is displayed.

12 Press the ENTER/OK button to start searching for analog

channels. The analog channel search will start and end

automatically. After all the available analog channels are stored,

the screen for searching digital channels is automatically

displayed.

➢

To stop the search before it has finished, press the

ENTER/OK button with Stop selected.

13 Press the ENTER/OK button to start searching for digital

channels. The digital channel search will start and end

automatically. After all the available digital channels are stored,

the screen to select a time zone is displayed depending on the

country.

➢

To stop the search before it has finished, press the

ENTER/OK button with Stop selected.

➢

If the DTV channel is updated, the Source in the source list

of the Input menu is automatically changed to DTV.

➢

For detailed descriptions about DTV channel update, refer

to page 36 of this manual.

14 Press the ▲ or ▼ button to select required time zone, then press the ENTER/OK button. The screen

for setting the time is displayed. Press the ENTER/OK button.

Continued...

Plug & Play

Some DTV functions may not be available.

Digitally Scan?

Move

Enter

Skip

Yes

No

Plug & Play

Auto Store

P 1 C -- 40 MHz

0 %

Enter

Skip

Start

Plug & Play

0%

Services found: 0 Channel:

-

Skip

Start

Plug & Play

Adjust

Move

Enter

01 01

2007

00

:

00

Clock Set

Month Day Year Hour

Minute





Plug & Play

Scanning for digital services...

29%

Services found: 6 Channel: 35

Skip

Stop

Plug & Play

Move

Select

Skip

The Iberian Peninsula and Balears Islands

Canarian Islands

BN68-01352E.F-00Eng(CIS).indd 11 2007-10-05 ¿ÀÈÄ 5:18:10

English - 12

Viewing External Signal Sources

You can switch between viewing signals from connected

equipment, such as a VCR, DVD, Set-Top Box, and the TV

source (broadcast or cable).

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Input, then press the

ENTER/OK button.

3 Press the ENTER/OK button again to select Source List.

4 Press the ▲ or ▼ button to select the signal source, then press

the ENTER/OK button.

Available signal sources:

TV, Ext.1, Ext.2, AV, S-Video,

Component, PC, HDMI1, HDMI2, HDMI3, DTV

➢

You can select these options simply by pressing the SOURCE

button on the remote control.

➢

To watch television programme again, press the TV/DTV button

and select the channel number required.

15 Press the ◄ or ► button to select Month, Day, Year, Hour, or

Minute. Set these by pressing the ▲ or ▼ button.

➢

You can set the Month, Day, Year, Hour, or Minute

directly by pressing the numeric buttons on the remote

control.

16 Press the ENTER/OK button to confirm your setting. The

message Enjoy your viewing is displayed. When you have

finished, press the ENTER/OK button.

➢

Even if the ENTER/OK button is not pressed, the message

will automatically disappear after several seconds.

If you want to reset this feature …

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Setup, then press the

ENTER/OK button.

3 Press the ENTER/OK button again to select Plug & Play.

The message Start Plug & Play is displayed.

OK

Enjoy your viewing

Plug & Play

Set the current time.

Adjust

Move

Select

Skip

01





15

Month Day Year

Hour Minute

2007

12 00

Move

Enter

Return

Source List : TV 

Edit Name



Anynet+(HDMI-CEC)

Input

T V

Move

Enter

Return

TV

Ext.1 :

−−−−

Ext.2 :

−−−−

AV : −−−−

S-Video :

−−−−

Component :

−−−−

PC :

−−−−

HDMI1 :

−−−−

HDMI2 : −−−−

HDMI3 :

−−−−

DTV :

−−−−

Source List

T V

Move

Enter

Return

Plug & Play



Language :

English 

Time



Game Mode : Off



Blue Screen :

Off 

Melody :

Off 

PC



Home Theatre PC : Off



Light Effect :

Standby Mode On



 More

Setup

T V

BN68-01352E.F-00Eng(CIS).indd 12 2007-10-05 ¿ÀÈÄ 1:52:42

English - 13

Editing Device Names

You can give a name to the external source.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Input, then press the

ENTER/OK button.

3 Press the ▲ or ▼ button to select Edit Name, then press the

ENTER/OK button.

4 Press the ▲ or ▼ button to select the external source to be

edited, then press the ENTER/OK button.

5 Select the required device by pressing ▲ or ▼, then press the

ENTER/OK button.

Available device names:

VCR, DVD, D-VHS, Cable STB, HD

STB, Satellite STB, AV Receiver, DVD Receiver, Game,

Camcorder, DVD Combo, DHR (DVD HDD Recorder), PC.

6 Press the EXIT button to exit.

➢

When a PC with a resolution of 1920 x 1080@60Hz is

connected to the HDMI IN 2 port, you should set the HDMI2

mode to PC in the Edit Name of the Input mode.

If the HDMI2 mode is not PC, it works depending on the TV

setting.

Storing Channels Automatically

➢

Not available in DTV or external input mode.

You can scan for the frequency ranges available to you

(availability depends on your country).

Automatically allocated programme numbers may not

correspond to actual or desired programme numbers. However

you can sort numbers manually and clear any channels you do

not wish to watch.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Channel, then press the

ENTER/OK button.

3 Press the ENTER/OK button again. The available countries are

listed.

4 Select your country by pressing the ▲ or ▼ button, then press

the ENTER/OK button.

➢

Even though you have changed the country setting in this

menu, the country setting for DTV is not changed. Use the

Plug & Play function to change the country setting for DTV.

(Refer to pages 10 to 12)

5 Press the ▲ or ▼ button to select Auto Store, then press the

ENTER/OK button.

6 Press the ENTER/OK button again to start the search.

The search will end automatically.

➢

To stop the search before it has finished, press the MENU

or the ENTER/OK button.

Move

Enter

Return

Source List :

TV 

Edit Name



Anynet+(HDMI-CEC)

Input

T V

Move

Enter

Return

Country :

United Kingdom



Auto Store



Manual Store



Channel Manager



Sort



Name



Fine Tune



LNA :

Off 

Channel

T V

Move

Enter

Return

Ext.1 :

−−−−

Ext.2 :

−−−−

AV :

−−−−

S-Video :

−−−−

Component :

−−−−

PC :

−−−−

HDMI1 :

−−−−

HDMI2 :

−−−−

HDMI3 :

−−−−

Edit Name

T V

−−−−

VCR

DVD

D-VHS

Cable STB

HD STB

Satellite STB

▼

Auto Store

P 1 C -- 40 MHz

0 %

Enter

Return

Start

Move

Enter

Return

Country :

United Kingdom

Auto Store

Manual Store

Channel Manager

Sort

Name

Fine Tune

LNA :

Off

Channel

T V

▲

Switzerland

United Kingdom

Austria

Eastern Europe

Others

▼

BN68-01352E.F-00Eng(CIS).indd 13 2007-10-05 ¿ÀÈÄ 1:52:47

English - 14

Storing Channels Manually

➢

Not available in DTV or external input mode.

You can store television channels, including those received via

cable networks.

When storing channels manually, you can choose:

 Whether or not to store each of the channels found.

 The programme number of each stored channel which you wish

to identify.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Channel, then press the

ENTER/OK button.

3 Press the ▲ or ▼ button to select Manual Store, then press

the ENTER/OK button.

4 Select the required option by pressing the ▲ or ▼ button, then

press the ENTER/OK button.

5 When you are satisfied with your setting, press the ENTER/OK

button.

6 Press the EXIT button to exit.

 Programme (Programme number to be assigned to a channel)

− Press the ▲ or ▼ button until you find the correct number.

➢

You can also select the channel number directly by pressing the numeric buttons (0~9).

 Colour System: Auto/PAL/SECAM/NTSC4.43

− Press the ▲ or ▼ button to select the required colour standard.

 Sound System: BG/DK/I/L

− Press the ▲ or ▼ button to select the required sound standard.

 Channel (When you know the number of the channel to be stored)

− Press the ▲ or ▼ button to select C (Air channel) or S (Cable channel).

− Press the ► button, then press the ▲ or ▼ button to select the required number.

➢

You can also select the channel number directly by pressing the numeric buttons (0~9).

➢

If there is abnormal sound or no sound, reselect the sound standard required.

 Search (When you do not know the channel numbers)

− Press the ▲ or ▼ button to start the search.

− The tuner scans the frequency range until the first channel or the channel that you selected is

received on the screen.

 Store (When you store the channel and associated programme number)

− Set to OK by pressing the ENTER/OK button.

☛

Channel mode

 P (Programme mode): When completing tuning, the broadcasting stations in your area have

been assigned to position numbers from P00 to P99. You can select a channel by entering the

position number in this mode.

 C (Air channel mode): You can select a channel by entering the assigned number to each air

broadcasting station in this mode.

 S (Cable channel mode): You can select a channel by entering the assigned number for each

cable channel in this mode.

Move

Enter

Return

Country :

United Kingdom



Auto Store



Manual Store



Channel Manager



Sort



Name



Fine Tune



LNA :

Off 

Channel

T V

Move

Enter

Return

Programme :

P 1

Colour System :

Auto 

Sound System :

BG 

Channel :

C 4

Search :

63 MHz

Store :

?

Manual Store

T V

BN68-01352E.F-00Eng(CIS).indd 14 2007-10-05 ¿ÀÈÄ 1:52:48

English - 15

Adding / Locking Channels

➢

Not available in DTV or external input mode.

Using the Channel Manager, you can conveniently lock or add

channels.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Channel, then press the

ENTER/OK button.

3 Press the ▲ or ▼ button to select Channel Manager, then

press the ENTER/OK button.

 Adding channels

Using the Channel List, you can add channels.

4 Select Channel List by pressing the ENTER/OK button.

5 Move to the ( ) field by pressing the ▲/▼/◄/► buttons,

select a channel to be added, and press the ENTER/OK button

to add the channel.

➢

If you press the ENTER/OK button again, the ( ) symbol

next to the channel disappears and the channel is not

added.

 Locking channels

This feature allows you to prevent unauthorized users, such as

children, from watching unsuitable programmes by muting out video

and audio.

6 Press the ▲ or ▼ button to select Child Lock, then press the ENTER/

OK button.

7 Select On by pressing the ▲ or ▼ button, then press the ENTER/OK

button.

8 Press the ▲ or ▼ button to select Channel List, then press the

ENTER/OK button.

9 Move to the ( ) field by pressing the ▲/▼/◄/► buttons, select a

channel to be locked, and press the ENTER/OK button.

➢

If you press the ENTER/OK button again, the ( ) symbol next to

the channel disappears and the channel lock is canceled.

➢

A blue screen is displayed when Child Lock is activated.

10 Press the EXIT button to exit.

➢

You can select these options simply by pressing the CH LIST

button on the remote control.

Move

Enter

Return

Country :

United Kingdom



Auto Store



Manual Store



Channel Manager



Sort



Name



Fine Tune



LNA :

Off 

Channel

T V

Move

Enter

Return

Channel List 

Child Lock :

Off 

Channel Manager

T V

Channel List

P 1 C 4

1 / 10

▲

▼

Prog.

0 C

-

1 C 4

2 C 24

3 C 2

4 C 5

5 C 80

6 C 7

7 C 36

8 C 52

9 C 11

Add Lock

Move Enter

Page

Return

BN68-01352E.F-00Eng(CIS).indd 15 2007-10-05 ¿ÀÈÄ 1:52:50

English - 16

Sorting the Stored Channels

➢

Not available in DTV or external input mode.

This operation allows you to change the programme numbers

of the stored channels.

This operation may be necessary after using the auto store.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Channel, then press the

ENTER/OK button.

3 Press the ▲ or ▼ button to select Sort, then press the ENTER/

OK button.

4 Select the channel that you wish to move by pressing the ▲ or

▼ button, then press the ENTER/OK button.

5 Select the number of the programme to which the channel is to

be moved by pressing the ▲ or ▼ button.

Press the ENTER/OK button. The channel is moved to its new

position and all other channels are shifted accordingly.

6 Repeat steps 4 to 5 until you have moved all the channels to

the required programme numbers.

7 Press the EXIT button to exit.

Assigning Names to Channels

➢

Not available in DTV or external input mode.

Channel names will be assigned automatically when channel

information is broadcast. These names can be changed,

allowing you to assign new names.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Channel, then press the

ENTER/OK button.

3 Press the ▲ or ▼ button to select Name, then press the

ENTER/OK button.

4 Press the ▲ or ▼ button to select the channel to be assigned to

a new name, then press the ENTER/OK button.

5 Press the ▲ or ▼ button to select a letter, a number, or a

symbol (Results in this sequence: A~Z, 0~9, +, -, *, /, blank).

Move on to the previous or next letter by pressing the ◄ or ►

button, then press the ENTER/OK button.

6 Repeat steps 4 to 5 for each channel to be assigned to a new

name.

7 Press the EXIT button to exit.

Move

Enter

Return

Country :

United Kingdom



Auto Store



Manual Store



Channel Manager



Sort



Name



Fine Tune



LNA :

Off 

Channel

T V

Move

Enter

Return

Prog. Ch. Name



0 C−−

1 C76

2 C5

3 C6

4 C7 



Sort

T V

Move

Enter

Return

Prog. Ch. Name



0 C−− −−−−−

1 C76 −−−−−

2 C5 −−−−−

3 C6 −−−−−

4 C7 −−−−−



Name

T V

Move

Enter

Return

Country :

United Kingdom



Auto Store



Manual Store



Channel Manager



Sort



Name



Fine Tune



LNA :

Off 

Channel

T V

BN68-01352E.F-00Eng(CIS).indd 16 2007-10-05 ¿ÀÈÄ 1:52:52

English - 17

Fine Tuning Channel Reception

➢

Not available in DTV or external input mode.

If the reception is clear, you do not have to fine tune the

channel, as this is done automatically during the search and

store operation.

If the signal is weak or distorted, you may have to fine tune the

channel manually.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Channel, then press the

ENTER/OK button.

3 Press the ▲ or ▼ button to select Fine Tune, then press the

ENTER/OK button.

4 To obtain a sharp, and clear picture and good sound quality,

press the ◄ or ► button until you reach the optimal setting.

Press the ENTER/OK button.

➢

To reset the fine tuning to 0, select Reset by pressing the

▲ or ▼ button. Press the ENTER/OK button.

5 Press the EXIT button to exit.

➢

Fine Tune Store will change the colour of the Channel OSD

(On Screen Display) from White to Red and add the “*”

mark.

LNA (Low Noise Amplifier)

This function is very useful in the situation that the TV is used

in weak signal.

LNA amplifies the TV signal in the weak signal area, a low-noise

preamplifier boosts the incoming signal.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Channel, then press the

ENTER/OK button.

3 Press the ▲ or ▼ button to select LNA, then press the ENTER/

OK button.

4 Select Off or On by pressing the ▲ or ▼ button, then press the

ENTER/OK button.

5 Press the EXIT button to exit.

➢

Depending on areas, factory mode of LNA, will be set up as On or Off.

Fine Tune

P 1

+3

Adjust

Save

Return

Reset

P 1 *

Mono

Picture : Dynamic

Sound : Custom

SRS TS XT : Off

−−

:

−−

Move

Enter

Return

Country :

United Kingdom



Auto Store



Manual Store



Channel Manager



Sort



Name



Fine Tune



LNA :

Off 

Channel

T V

Move

Enter

Return

Country :

United Kingdom



Auto Store



Manual Store



Channel Manager



Sort



Name



Fine Tune



LNA :

Off 

Channel

T V

BN68-01352E.F-00Eng(CIS).indd 17 2007-10-05 ¿ÀÈÄ 1:52:53

English - 18

Changing the Picture Standard

You can select the type of picture which best corresponds to

your viewing requirements.

1 Press the MENU button to display the menu.

2 Press the ENTER/OK button to select Picture.

3 Press the ENTER/OK button again to select Mode.

4 Select the required mode by pressing the ▲ or ▼ button, then

press the ENTER/OK button.

Available modes:

Dynamic, Standard, Movie

➢

The settings values may vary depending on the input

source. (ex. RF, Video, Component, PC, or HDMI)

5 Press the EXIT button to exit.

➢

You can select these options simply by pressing the P.MODE

button on the remote control.

➢



Choose Dynamic for viewing the TV during the day or

when there is bright light in the room.



Choose Standard for general TV watching mode.



Choose Movie when viewing the movie.

Customizing the Picture Settings

Your television has several setting options that allow you to

control the picture quality.

1 Press the MENU button to display the menu.

2 Press the ENTER/OK button to select Picture.

3 Press the ENTER/OK button again to select Mode.

4 Select the required mode by pressing the ▲ or ▼ button, then

press the ENTER/OK button.

Available modes:

Dynamic, Standard, Movie

5 Select the required option by pressing the ▲ or ▼ button, then

press the ENTER/OK button.

6 When you are satisfied with your setting, press the ENTER/OK

button.

7 Press the EXIT button to exit.

 Contrast – Brightness – Sharpness – Colour – Tint

➢

In TV, AV, S-Video modes of the PAL system, you cannot

use the Tint Function.

Contrast – Brightness – Colour Tone : PC Mode

Press the ◄ or ► button until you reach the optimal setting.

 Colour Tone: Cool2/Cool1/Normal/Warm1/Warm2

➢

When the picture mode is set to Dynamic or Standard, Warm1 and Warm2 cannot be selected.

 Reset: Cancel/OK

Select

OK. You can return to the factory defaults picture settings.

➢

The reset function is set for each picture mode and colour tone.

Move

Enter

Return

Mode :

Dynamic 

Contrast 100

Brightness 45

Sharpness 75

Colour 55

Tint G 50 R 50

Colour Tone :

Cool1 

Detailed Settings



 More

Picture

T V

Move

Enter

Return

Mode : Dynamic

Contrast 100

Brightness 45

Sharpness 75

Colour 55

Tint G 50 R 50

Colour Tone :

Cool1

Detailed Settings



 More

Picture

T V

Dynamic

Standard

Movie

Move

Enter

Return

Mode : Dynamic

Contrast 100

Brightness 45

Sharpness 75

Colour 55

Tint G 50 R 50

Colour Tone : Cool1

Detailed Settings �

 More

Picture

T V

Cool2

Cool1

Normal

Warm1

Warm2

Move

Enter

Return

Mode :

Dynamic 

Contrast 100

Brightness 45

Sharpness 75

Colour 55

Tint G 50 R 50

Colour Tone :

Cool1 

Detailed Settings



 More

Picture

T V

BN68-01352E.F-00Eng(CIS).indd 18 2007-10-05 ¿ÀÈÄ 1:52:54

English - 19

Configuring Detailed Settings on the Picture

You can set detailed picture settings.

1 Press the MENU button to display the menu.

2 Press the ENTER/OK button to select Picture.

3 Press the ▲ or ▼ button to select Detailed Settings, then

press the ENTER/OK button.

4 Select the required option by pressing the ▲ or ▼ button, then

press the ENTER/OK button.

Available options: Black Adjust

, Dynamic Contrast, Gamma,

White Balance, My Colour Control, Edge Enhancement,

Colour Space, xvYCC

5 When you are satisfied with your setting, press the ENTER/OK

button.

6 Press the EXIT button to exit.

➢

When the picture mode is set to Movie or Standard, Detailed

Settings can be selected.

➢

If DNIe is Off, the Detailed Settings cannot be selected when

the Picture mode is in Standard mode.

 Black Adjust: Off/Low/Medium/High

You can directly select the black level on the screen to adjust the screen depth.

 Dynamic Contrast: Off/Low/Medium/High

You can adjust the screen contrast so that the optimal contrast is provided.

 Gamma: -3 ~ +3

You can adjust the middle brightness of pictures.

Press the ◄ or ► button until you reach the optimal setting.

 White Balance: R-Offset/G-Offset/B-Offset/R-Gain/G-Gain/B-Gain/Reset

You can adjust the colour temperature for more natural picture colors.

R-Offset/G-Offset/B-Offset/R-Gain/G-Gain/B-Gain: Changing the adjustment value will refresh the

adjusted screen.

Select the required option by pressing the ▲ or ▼ button, then press the ENTER/OK button. Press

the ◄ or ► button until you reach the optimal setting.

Reset: The previously adjusted white balance will be reset to the factory defaults.

 My Colour Control: Pink/Green/Blue/White/Reset

This setting can be adjusted to suit your personal preferences.

Pink/Green/Blue/White: Changing the adjustment value will refresh the adjusted screen.

Select the required option by pressing the ▲ or ▼ button, then press the ENTER/OK button. Press

the ◄ or ► button until you reach the optimal setting.

Reset: The previously adjusted colours will be reset to the factory defaults.

 Edge Enhancement: Off/On

You can emphasize object boundaries.

 Colour Space: Auto/Wide

You can set the colour reproduction space for the input signal to Auto or Wide.

 xvYCC: Off/On

Setting the xvYCC mode to On increases detail and colour space when watching movies from an

external device (ie. DVD player) connected to the HDMI or Component IN jacks. You must set the

Picture Mode to Movie to enjoy this feature.

➢

The xvYCC function works only in Component or HDMI mode.

Move

Enter

Return

Mode :

Movie 

Contrast 80

Brightness 45

Sharpness 10

Colour 53

Tint G 50 R 50

Colour Tone :

Warm2 

Detailed Settings 

 More

Picture

T V

Move

Enter

Return

Black Adjust : Off 

Dynamic Contrast :

Off 

Gamma :

0 

White Balance 

My Colour Control



Edge Enhancement

: Off 

Colour Space :

Auto 

xvYCC : Off



Detailed Settings

T V

BN68-01352E.F-00Eng(CIS).indd 19 2007-10-05 ¿ÀÈÄ 1:52:57

English - 20

Selecting the Picture Size

You can select the picture size which best corresponds to your

viewing requirements.

1 Press the MENU button to display the menu.

2 Press the ENTER/OK button to select Picture.

3 Press the ▲ or ▼ button to select Size, then press the ENTER/

OK button.

4 Select the required option by pressing the ▲ or ▼ button, then

press the ENTER/OK button.

Available options: Auto Wide

, 16:9, Wide Zoom, Zoom, 4:3,

Just Scan

 Auto Wide: Expands and pulls up the picture from 4:3 to

16:9 ratio.

 16:9: Sets the picture to 16:9 wide mode.

 Wide Zoom: Magnifies the size of the picture more than

4:3. Move the screen up/down using the ▲ or ▼ button

after selecting the by pressing the ► or ENTER/OK

button.

 Zoom: Magnifies the size of the picture vertically on

screen.

 4:3: Sets the picture to 4:3 normal mode.

 Just Scan: Displays the input scenes as they are without

any cutoff when HDMI 720p, 1080i, 1080p signals are

input.

➢

With the HDMI Just Scan picture size, depending on

the AV devices, the screen may be cut off or a specific

colour appears on the screen.

5 Press the EXIT button to exit.

➢

You can change the picture size simply by pressing the P.SIZE button on the remote control.

➢

Depending on the input source, the picture size options may vary.

➢

The items available may differ depending on the selected mode.

Positioning and Sizing the screen using Zoom

 Resizing the screen using the Zoom enables the positioning and sizing of the screen to up/down

direction using the ▲ or ▼ button as well as the screen size.

 Move the screen up/down using the ▲ or ▼ button after selecting the by pressing the ◄ or ►

button.

 Resize the screen vertically using the ▲ or ▼ button after selecting the by pressing the ◄ or ►

button.

Selecting the Screen Mode

When setting the picture size to Auto Wide in a 16:9 wide TV,

you can determine the picture size you want to see the 4:3

WSS (Wide Screen Service) image or nothing. Each individual

European country requires different picture size so this

function is intended for users to select it.

1 Press the MENU button to display the menu.

2 Press the ENTER/OK button to select Picture.

3 Press the ▲ or ▼ button to select Screen Mode, then press

the ENTER/OK button.

4 Select the required option by pressing the ▲ or ▼ button, then

press the ENTER/OK button.

Available options:

16:9, Wide Zoom, Zoom, 4:3

 16:9: Sets the picture to 16:9 wide mode.

 Wide Zoom: Magnifies the size of the picture more than 4:3.

 Zoom: Magnifies the size of the picture vertically on screen.

 4:3: Sets the picture to 4:3 normal mode.

5 When you are satisfied with your setting, press the ENTER/OK button.

6 Press the EXIT button to exit.

Move

Enter

Return

 More

Size :

Auto Wide 

Screen Mode : 16 : 9 

Digital NR :

Auto 

Active Colour : On 

DNIe :

On 

Movie Plus :

On 

Reset :

OK 

Picture

T V

Move

Enter

Return

Auto Wide

16:9

Wide Zoom

Zoom

4:3

Just Scan

Size

T V

Move

Enter

Return

 More

Size :

Auto Wide 

Screen Mode : 16 : 9 

Digital NR :

Auto 

Active Colour : On 

DNIe :

On 

Movie Plus :

On 

Reset :

OK 

Picture

T V

BN68-01352E.F-00Eng(CIS).indd 20 2007-10-05 ¿ÀÈÄ 1:52:58

La page charge ...

Samsung PS-58P96FDR Manuel utilisateur

Ce manuel convient également à

Samsung PS-58P96FDR Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents