King KS1000 Swift Range Wi-Fi Extender and WifiMax Router Manuel utilisateur

Marque: King

Modèle: KS1000 Swift Range Wi-Fi Extender and WifiMax Router

Taper: Manuel utilisateur

Ce manuel convient également à

Page 1

Wi-Fi Extender KWM1000

(included with KS1000)

(not included with KWM1000)

Omnidirectional Wi-Fi Antenna KS1000

SWIFT

The KING WiFiMax creates your own private and secure Wi-Fi

network, just like you have in your home. When in range of an

network, and it will extend the internet access from that network to

your own private Wi-Fi network.

The KING Swift is an omnidirectional Wi-Fi antenna

that increases the range and performance of your

KING WiFiMax router and range extender. This

2.4GHz Wi-Fi antenna mounts to your roof, connects

to your KING WiFiMax via a single cable, and allows

your KING WiFiMax to connect to networks from

even farther away and still utilize its 5GHz network for

fastest speeds.

CONTENTS

CONTENTS ................................................................................................. 2

CONNECTIONS .......................................................................................... 3

FIRST-TIME USE ..................................................................................... 4-7

STANDARD OPERATION ..................................................................... 8-11

INSTALLATION ................................................................................... 12-13

TROUBLESHOOTING .............................................................................. 14

SPECIFICATIONS .................................................................................... 15

LIMITED WARRANTY ......................................................................... 16-17

WIRELESS REGULATORY INFORMATION ....................................... 18-19

Page 2

KING Swift antenna

with preattached cable

White

wall plate

Black

wall plate

Cable

Watertight connector

Washer

Pole, ladder or

mirror-mount

bracket

Roof-mount

bracket

Manual

Power Supply

Dipole Antenna

KING WiFiMax

Nut

CONTENTS

KING WiFiMax KWM1000

For increased performance, you can add a KING Swift

(contact KING Customer Service at 952-345-8147).

KING Swift KS1000

Includes the KING WiFiMax and

power supply shown above.

NOTE: The KING Swift, bracket and hardware may come preassembled.

For complete installation instructions see page 10.

NOTE: No tools are required to set up and use the KING WiFiMax (unless wall

mounting the unit).

There are key hole slots on the back to mount the unit to a wall. The

user must determine where and how to best mount the unit to a wall

(inside use only).

Page 3

Attach included dipole antenna or cable from KING Swift to open port.

Rotate antennas so they point up.

Connect to power.

CONNECTIONS

Place your KING WiFiMax on a stable surface (or wall mount).

Make connections as shown. (Blue lights on KING WiFiMax will turn on when

power is connected.)

NOTE: You can use the keyhole slots on the back to wall mount the unit.

ANTENNAS MUST ALWAYS POINT UP.

Page 4

Graphics will vary.

FIRST-TIME USE

NOTE:

1. Go to your smart phone, tablet or

computer’s Wi-Fi settings page and

connect to the KING 5G network:

If you do not see KING_XXXXXX_5G (5GHz network), connect to KING_XXXXXX

(2.4GHz network).

Always choose the 5G network if possible, as it is faster than the 2.4GHz network.

KING_XXXXXX_5G

TIP

When using a smart phone or tablet: to maintain the best connection

to your KING WiFiMax, it is suggested that the smart phone or tablet’s

TIP

XXXXXX is a number/letter

combination unique to your router

and can be found on the bottom of

your router in the SSID row.

Page 5

2. Open your device’s web browser.

Go to:

Tap “WiFi Settings” in the left-hand column.

Type exactly as written.

3. Tap “WiFi Name & Password.”

Page 6

4. In the screen below, you MUST change your Wi-Fi name and password to personalize

it and keep it secure. Do steps A and B for both the 2.4 GHz and 5GHZ networks (you

will only have to do this once).

TIP

When entering your new names, make sure to the

existing names in the boxes.

2.4GHz network name.

TIP

KING highly recommends password protecting your name.

Choose WPA/WPA2-PSK under “Encryption Mode” to enable

password protection.

Passwords can be the same for both networks if you wish, and must

be at least 8 characters.

Choose this

encryption

mode to enable

password

protection.

Enter a new Wi-Fi name.

Enter a password.

Enter names and passwords for both networks.

Page 7

2.4GHZ

5GHZ

Write your network name here: Write your password here:

You have personalized your router setup.

Continue on next page.

5. When you have entered names and passwords for both networks, tap “Save.”

TIP

If the “Save” button

does not appear, scroll

TIP

Page 8

1. Go to your phone, tablet or computer’s settings

page and connect to the Wi-Fi Network with your

personalized network name (you created this on

page 6).

The example shown is “MyWiFiName_5G”.

If your device cannot connect to your 5G

network, connect to your other network.

STANDARD OPERATION

2. Open your device’s web browser.

Go to:

Tap “WiFi Settings” in the left-hand column.

2.4GHz: MyWiFiName

5GHz: MyWiFiName_5G

Type exactly as written.

When using a smart phone

or tablet: to maintain the best

connection to your KING WiFiMax, it

is suggested that the smart phone or

during standard operation.

TIP

For best performance, choose the

5GHz network whenever possible.

TIP

Page 9

3. Tap “Wireless Repeating.”

4. Tap the blue arrows to scan for networks.

Page 10

The router is scanning for networks.

5. After the scanning process is complete, this screen will appear.

Tap on “Upstream WiFi Name” drop down menu to display a list of available networks.

If the upstream

network you are

looking for does not

appear in this list,

scroll up and down

TIP

Page 11

6. Select the network you would like to extend (not your customized router name) and

input the password if necessary (not pictured).

Tap “Save.”

7. This popup should appear. Tap “OK.”

8. Your KING WiFiMax will reboot.

If your router gets stuck at 100% and won’t

or if your Wi-Fi device does not have

internet access, you may need to go back

to your smart phone or tablet’s settings

page and ensure that it reconnected to

the Wi-Fi network with your personalized

network name, as you may lose connection

during the router’s rebooting process.

Your KING WiFiMax is now extending your network!

standard operation, it is now safe to turn it back on.

TIP

Page 12

INSTALLATION

1. Drill 5/16” hole in roof where cable will enter roof. Feed long cable into position with

enough cable sticking out of roof to attach KING Swift cable. This end is marked

“ROOF” and is red.

2. Connect KING Swift cable and long cable.

3. Apply roof-compatible sealant around perimeter of bracket. Feed cable into hole, lower

bracket into position and fasten to roof.

4. Inside vehicle, install wall plate if desired, and connect cable to KING WiFiMax.

• For best performance, the antenna should be located as far away as possible from

other rooftop objects (TV antennas, AC units, etc.) and with the best all around line of

sight.

• When determining locations, make sure the long cable will reach the KING WiFiMax

when attached to the KING Swift cable. (KING Swift cable may go directly to prewire

enclosure - see opposite page).

• Do not locate the KING WiFiMax or KING Swift in a slide-out.

• Cable connection between KING Swift and long cable must always be inside vehicle

(or prewire enclosure if using).

You can also use the included

bracket to mount the antenna

to a pole, ladder or mirror.

Page 13

IMPORTANT!

The installer is responsible for determining and

All holes, fastener heads, and the entire perimeter

weatherproofed with sealant.

Page 14

TROUBLESHOOTING

The KING WiFiMax doesn’t power on (no blue lights on front).

Make sure power supply plug is securely inserted into back of KING WiFiMax. Make

sure the power supply is plugged into a known good power outlet.

Make sure your KING WiFiMax is plugged in. It may take up to a minute for these

networks to appear. Some older devices may be unable to see the 5GHz network.

This is completely okay; just use the KING_XXXXXX network.

Make sure you are connected to your KING WiFiMax’s network. Then make sure you

type in the web address exactly as it appears in this manual: .

Choose WPA/WPA2-PSK under “Encryption Mode” (right above the password box)

to enable password protection.

I don’t see the Upstream WiFi name I want to extend in my list of networks.

If a network is very far away or very weak, the KING WiFiMax may not be able to see

KING WiFiMax to a location closer to your desired network.

Try reloading the page. If the page won’t load, make sure your device is still

connected to the KING WiFiMax. It may have disconnected during the reboot.

The KING WiFiMax doesn’t seem to extend the range of my Wi-Fi, or has trouble

Make sure all 4 antennas (3 if KING Swift is connected) are pointing up. If wall

mounting, antennas must be rotated to point up as well.

Certain types of obstructions (other vehicles, buildings, or large amounts of metal)

can reduce signal levels. Try relocating the KING WiFiMax.

NOTE: KING WiFiMax can be reset by

pressing and holding

the reset button until the front

lights go out (15-20 seconds).

Page 15

KING WiFiMax

Power: Included 12v power supply,

requiring 110V AC plug-in

Wireless standards: IEEE802.11a/b/g/n/ac

Supported Frequencies: 2.4GHz and 5GHz (dual-band)

Security: WPA/WPA2-PSK

Storage Environment: Temperature -40ºF to 158ºF

KING Swift

Radio Frequency Band: 2.4GHz

Wireless Standards: IEEE802.11a/b/g/n

Antenna: 3dBi roof-mounted omnidirectional antenna

Height: 9.5”

Diameter: 0.75”

Weight: 0.25LBS

SPECIFICATIONS

Page 16

LIMITED WARRANTY

Each new KING WiFiMax and King Swift is thoroughly inspected and tested before leaving

the factory, and is covered by the following limited warranty from the date of original

purchase:

• One-year parts warranty: The customer is not responsible for the cost of

replacement parts if the original part is determined to be defective under the terms

of the warranty. The customer is responsible for the cost of replacement parts after

one year.

Depending upon the problem, KING may authorize a dealer to perform the necessary

repairs. Any warranty labor outside of that performed at the factory is not covered unless

1) the product has been installed by an authorized dealer/installer or OEM manufacturer

and 2) the dealer/installer receives prior authorization to perform the repair.

Order Number. KING will advise the dealer on how to proceed with any repairs.

Should any trouble develop during the warranty period, contact KING at (952) 345-8147.

You must contact KING before the warranty period expires. The customer must supply

proof of purchase (such as a dated sales receipt) when requesting warranty service. If the

customer cannot supply proof of purchase, warranty period shall start 30 days after date

of manufacture.

If it is determined that the unit needs to be returned to KING, customer must return

COMPLETE product, freight prepaid, to:

KING, 11200 Hampshire Avenue South, Bloomington, MN 55438-2453.

If inspection shows the trouble is caused by defective workmanship or material, KING will

repair (or at its option, replace) without charge.

When returning product, KING will supply an RMA number (Return Merchandise

Authorization). This number must be clearly written on the box. Failure to clearly write

RMA number on box will result in delays in processing claim. Along with product, the

customer should include in the box: his/her name, address, daytime phone number, proof

of purchase and description of the problem.

This warranty does not cover installation and external wiring, or remanufactured units.

This warranty does not cover damage caused by the use of an accessory other than

a KING accessory designed for the product. This warranty is not transferable from the

original owner.

KING cannot be held responsible for changes in the expanding and changing digital and

analog communications market that cause the product to no longer operate correctly.

Page 17

This warranty also does not apply where:

• The product has been abused, misused, improperly installed or improperly

maintained.

• The product has been used with an accessory other than a KING accessory

designed for the product.

such repairs.

• Repairs are required because of normal wear and tear.

• Alterations have been made to the product.

• The product or any associated component has been opened without authorization or

disassembled to any degree.

• Damage has been caused by power washing.

• Circumstances beyond the control of KING cause the product to no longer operate

correctly.

• Customer is not the original owner.

In no event shall KING be liable for any indirect, incidental, or consequential damages

from the sale or use of the product. This disclaimer applies both during and after the term

of this warranty.

KING disclaims liability for any implied warranties, including implied warranties of

vary from state to state. Some states do not allow the exclusion or limitation of incidental

or consequential damages, so the above limitation or exclusion may not apply to you.

Some states do not allow limitations on how long an implied warranty lasts, so the above

limitation may not apply to you.

Page 18

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution

ment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The device for the band 5150-5250 MHz is only for indoor usage to reduce the potential for harmful interference to co-channel mobile satellite

systems.

Radiation Exposure Statement

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF

Rules. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.

CAN ICES-3 (B)/NMB-3(B)

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s

licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must

accept any interference, including interference that may cause undesired operation of the device.

For product available in the USA/Canada market, only channel 1-11 can be operated. Selection of other channels is not possible.

The device could automatically discontinue transmission in case of absence of information to transmit, or operational failure. Note that this is not

intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by the technology.

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and

operated with minimum distance 20 cm between the radiator and your body.

This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with

ISED multi-transmitter product procedures.

The device for the band 5150-5250 MHz is only for indoor usage to reduce the potential for harmful interference to co-channel mobile satellite

systems.

point-to-point operation as appropriate.

Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850

MHz and that these radars could cause interference and/or damage to LE-LAN devices.

This radio transmitter (6873A-KWM1000) has been approved by Innovation, Science and Economic Development Canada to operate with the

antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the

maximum gain indicated for any type listed are strictly prohibited for use with this device.

Additional requirements for the band 5600-5650 MHz

Until further notice, devices subject to this Section shall not be capable of transmitting in the band 5600-5650 MHz, so that Environment Canada

weather radars operating in this band are protected.

WIRELESS REGULATORY INFORMATION

Page 19

CAN ICES-3 (B)/NMB-3(B)

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement

économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) L’appareil

ne doit pas produire de brouillage; et (2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en

compromettre le fonctionnement.

Pour les produits disponibles sur le marché aux États-Unis et au Canada, seuls les canaux de 1 à 11 peuvent être utilisés. La sélection d’autres

canaux n’est pas possible.

Le dispositif peut automatiquement cesser d’émettre en cas d’absence d’informations à transmettre, ou à cause d’une défaillance technique. Notez

que l’objet n’est pas d’interdire la transmission des informations de contrôle ou de signalisation ou l’utilisation de codes répétitifs lorsque requis par

la technologie.

Ce matériel est conforme aux limites établies par ISED en matière d’exposition aux radiofréquences dans un environnement non contrôlé. Ce

matériel doit être installé et utilisé à une distance d’au moins 20 cm entre l’antenne et le corps de l’utilisateur.

Cet appareil et son (ses) antenne(s) ne doivent pas être situés à proximité ou fonctionner en association avec une autre antenne ou un autre émet-

teur autre qu’en respectant les procédures d’ ISED relatives au fonctionnement des dispositifs multi-émetteurs.

systèmes mobiles par satellite qui utilisent le même canal.

l’exploitation point à point et non point à point, selon le cas.

De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d.,

qu’ils ont la priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages

aux dispositifs LAN-EL.

Le présent émetteur radio (6873A-KWM1000) a été approuvé par Innovation, Sciences et Développement économique Canada pour fonctionner

avec les types d’antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types d’antenne non inclus dans cette liste, et dont le gain

radars météorologiques d’Environnement Canada fonctionnant dans cette bande soient protégés.