Power Fist 8442923 Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
V1.0 8442923
Please read and understand all instructions before use. Retain this manual for
future reference.
8442923 2-3/4 Ton Pallet Jack V1.0
2 For technical questions call 1-800-665-8685
SPECIFICATIONS
Lift Capacity 2-3/4 Ton
Lift Capacity 5,500 lb
Min. Lift Height 3 in.
Max. Lift Height 7-1/2 in.
Fork Size 48 in.
Distance Between Fork 14-3/8 in.
Turning Radius 230°
Material Carbon steel
Finish Powder coated
Wheel Size 7 in.
Wheel Material Nylon
Handle Type Steel tube
Handle Material Steel
Dimensions 27 x 48 in.
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this manual. A
notice is an alert that there is a possibility of property damage, injury or
death if certain instructions are not followed.
DANGER! This notice indicates an immediate and specific hazard that
will result in severe personal injury or death if the proper
precautions are not taken.
WARNING! This notice indicates a specific hazard or unsafe practice that
could result in severe personal injury or death if the proper
precautions are not taken.
CAUTION! This notice indicates a potentially hazardous situation that may
result in minor or moderate injury if proper practices are not
taken.
NOTICE! This notice indicates that a specific hazard or unsafe practice
will result in equipment or property damage, but not personal
injury.
V1.0 2-3/4 Ton Pallet Jack 8442923
Visit www.princessauto.com for more information 3
INTRODUCTION
The pallet jack is designed for the transportation of loads with a level,
fixed base.
SAFETY
WARNING! Read and understand all instructions before using this tool. The
operator must follow basic precautions to reduce the risk of personal injury
and/or damage to the equipment.
Keep this manual for safety warnings, precautions, operating or inspection
and maintenance instructions.
WORK AREA
1. Operate in a safe work environment. Keep your work area clean, well-lit
and free of distractions. Place lights so you are not working in a shadow.
2. Keep anyone not wearing the appropriate safety equipment away from
the work area.
3. Store unused tools properly in a safe and dry location to prevent rust
or damage. Lock tools away and keep out of the reach of children.
PERSONAL SAFETY
WARNING! Wear personal protective equipment approved by the Canadian
Standards Association (CSA) or American National Standards Institute (ANSI).
PERSONAL PROTECTIVE EQUIPMENT
1. Always wear impact safety goggles that provide front and side protection
for the eyes. Eye protection equipment should comply with CSA Z94.3-07
or ANSI Z87.1 standards based on the type of work performed.
2. Wear gloves that provide protection based on the work materials or to
reduce the effects of tool vibration.
3. Wear protective clothing designed for the work environment and tool.
4. Non-skid footwear is recommended to maintain footing and balance in
the work environment.
PERSONAL PRECAUTIONS
Control the tool, personal movement and the work environment to avoid
personal injury or damage to tool.
1. Do not operate any tool when tired or under the influence of drugs,
alcohol or medications.
8442923 2-3/4 Ton Pallet Jack V1.0
4 For technical questions call 1-800-665-8685
2. Avoid wearing clothes or jewelry that can become entangled with the
moving parts of a tool. Keep long hair covered or bound.
3. Do not overreach when operating a tool. Proper footing and balance
enables better control in unexpected situations.
5. Securely hold this tool using both hands. Using a tool with only one
hand can result in loss of control.
SPECIFIC SAFETY PRECAUTIONS
WARNING! DO NOT let comfort or familiarity with product (gained from
repeated use) replace strict adherence to the tool safety rules. If you use
this tool unsafely or incorrectly, you can suffer serious personal injury.
1. Use the correct tool for the job. This tool was designed for a specific
function. Do not modify or alter this tool or use it for an unintended
purpose.
2. Do not use the tool if any parts are damage broken or misplaced.
Repair or replace the parts.
3. Before lowering load, ensure that there are no obstructions underneath
and that all people are standing clear.
4. Never allow anyone to ride on the pallet jack.
5. Operate on smooth, level, finished floors only; do not use on ramps or
sloping floors.
6. To prevent accidental tipping, make sure load is centered on the pallet
jack’s forks.
7. Do not lift a load with fork tips only. This may cause damage to the forks
and personal injury if the rear of the pallet jack suddenly tips upward.
8. Know the weight of the load being lifted. Do not exceed the maximum
capacity (see Specifications). Overloading can cause damage to or
failure of the jack.
9. Never leave a loaded pallet jack unattended in the raised position.
Always lower the load to the floor.
10. Pull pump release lever slowly to allow load to descend in a controlled
manner.
11. Secure load before transporting.
12. Only move the loaded pallet jack by manual force.
13. The handle is designed to pull and steer the pallet jack only. Do not use
the handle as a leverage tool.
V1.0 2-3/4 Ton Pallet Jack 8442923
Visit www.princessauto.com for more information 5
HYDRAULIC JACK PRECAUTIONS
1. Never attempt to use the jack unless it is properly filled with hydraulic
fluid.
2. Make sure there is enough clearance around the pallet jack and the
load for movement.
3. Do not place your hands between the moving components.
4. Inspect the tool before each use. DO NOT use if bent, broken, cracked,
leaking, otherwise damaged, if any suspect parts are noticed or it has
been subjected to a shock load.
5. Check to ensure that all applicable bolts and nuts are firmly tightened.
HYDRAULIC PRECAUTIONS
DANGER! Seek immediate medical attention if hydraulic fluid under
pressure penetrates your skin. See Injection Injury precautions for
instructions before using a pressurized hydraulic system.
1. Do not touch or handle hydraulic hoses or components while under
pressure. Hydraulic fluid escaping under pressure has sufficient force
to penetrate your clothing and skin. A pinpoint hole may inject
hydraulic fluid into your body. Seek immediate medical attention if this
occurs (see Injection Injury).
2. Never exceed the hydraulic system’s load capacity (see Specifications).
3. Do not adjust the hydraulic system’s relief setting. The settings are pre-
set by the factory.
4. Hydraulic oil under pressure is hot and can cause a burn injury if
touched, sprayed or spilled. Allow the hydraulic system to cool before
conducting maintenance.
5. Hydraulic components require regular inspection. Release all pressure
from the system before you inspect it. Replace damaged hydraulic
parts with identical manufacturer's components.
6. Do not attempt makeshift repairs to a hydraulic system. Such repairs
can fail suddenly and create a hazardous condition.
7. A damaged or disconnected hydraulic hose under pressure may whip
around and inflict personal injury or damage the work area. Secure the
hose to a fixed or permanent structure with clamps or cable ties.
8. Hydraulic fluid has a combustible flash point of 200°F (93°F). Do not
expose the fluid to an ignition source.
8442923 2-3/4 Ton Pallet Jack V1.0
6 For technical questions call 1-800-665-8685
9. Change your clothing immediately if sprayed with hydraulic fluid. Store
clothing or rags contaminated with hydraulic fluid in an approved
metal safety can with a spring-closing lid and venting designed to
contain a fire.
10. Only use hydraulic fluid in the pump. Do not substitute or mix brake fluid,
or any other fluid, with the hydraulic fluid. This can result in a pump
failure and injure the user or bystander. It may also damage the pump.
INJECTION INJURY
DANGER! Seek immediate, professional medical treatment if fluid
penetrates your skin. It may feel like a pricking or sting. Do not wait for the
appearance of symptoms. A toxic reaction can occur from the exposure.
Delay in treatment can lead to amputation or death.
Inform the medical staff that you have a fluid penetration injury as soon as
you arrive at the medical facility. The severity of the symptoms will depend
on the type of fluid injected. Bring the Safety Data Sheet for the fluid with
you to the medical facility if possible.
INJECTION PRECAUTIONS
Fluid can penetrate the skin at 100 PSI pressure. Fluid escaping under
pressure from the tool has sufficient force to penetrate your clothing and
skin. Follow the precautions below to avoid an injection injury.
1. Always check for leaks wearing a face shield, safety goggles,
rubberized gloves and protective clothes.
2. Release all pressure from the system before you inspect it.
3. Do not use your hands to detect a fluid leak. Use a large piece of wood,
cardboard or paper and watch for discolouration.
4. Replace damaged parts with identical manufacturer's components to
ensure it is rated to handle the pressure.
UNPACKING
WARNING! Do not operate the tool if any part is missing. Replace the
missing part before operating. Failure to do so could result in a malfunction
and personal injury.
Remove the parts and accessories from the packaging and inspect for damage.
Make sure that all items in the contents are included.
Contents: • Handle • Shaft • Pallet Jack
• Hardware (washers & screws).
V1.0 2-3/4 Ton Pallet Jack 8442923
Visit www.princessauto.com for more information 7
ASSEMBLY & INSTALLATION
Letter references in parenthesis (A) refer to the included Identification Key.
Dashed numbers in parenthesis (Fig. 1-1) refer to a specific point in an
illustration or image.
TOOLS REQUIRED FOR ASSEMBLY
• Allen Key (8 mm) • Flat Head Screwdriver
ASSEMBLY
1. Put the base of the handle tube (Fig.
1-1) on the pressure plate (Fig. 1-2).
Align the holes (Fig. 1-3) at the base
of the handle with the holes in the
pressure plate. The chain should drop
through the middle hole of the shaft
(Fig. 2-1).
2. Use a screwdriver to pry the lever
plate (Fig. 2-2) up and slip the bolt
head under the notch in the lever
plate. Do not adjust the nut unless
the pallet jack doesn’t work properly.
CAUTION! Do not loosen or over tighten the
lock nut (#13). The nut is pre-locked onto
the bolt at the factory.
3. Secure the handle to the pallet jack by
the three screws (Fig. 1-3) and spring
washers (Fig. 1-4).
IMPORTANT! It is a good idea to remove any
air bubbles that might have accumulated in
the hydraulic system during shipping (see
Bleeding the Hydraulic System).
OPERATION
This pallet jack is designed for use with open style pallets or skids only.
Closed style pallets must be placed on top of fork prior to use.
1. Insert the fork into the pallet.
2. To raise the fork, push control lever all the way down, and pump the
handle until the desired fork height is reached.
Fig.
1
Fig. 2
8442923 2-3/4 Ton Pallet Jack V1.0
8 For technical questions call 1-800-665-8685
3. To move the handle without affecting the fork setting, set the control
lever in the center neutral position. The load can now be pushed or
pulled using the handle.
4. To lower the fork, pull lever all the way up. Allow the load to descend
slowly in a controlled manner. The lever is spring-loaded and will
return to the neutral position when released.
WARNING! When not in use, do not allow heavy loads to remain on the fork
for an extended period of time. Always lower fork completely when not in
use.
ADJUSTING THE CONTROL HANDLE'S
THREE POSITIONS
On the handle tube (#1) of this pallet jack, you can find the control lever
(#5), which can be regulated in three positions (Fig. 3).
LOWER Pull the control lever up and the
forks/load will lower to the
desired height. The control lever
will move back the neutral
position when released.
NEUTRAL When the control lever is in the
middle position the forks will
not move when the handle tube
is pumped. The control lever
must be in the neutral position when the truck is driven.
LIFT Push the control lever down and pump the handle tube to raise
the forks/load to the desired height.
These three positions are set at the factory
to work as soon as the handle tube is
attached. Check to see if each of the 3
control lever positions work well. If the
forks do not raise or lower as expected,
proceed to the following steps (Fig. 4).
1. Set the control lever (Fig. 3) to the
lower position. If the fork frame does
not lower, turn the nut (#13) clockwise
until the fork frame lowers.
2. Push the control lever down to the lift position. If the fork frame does not
elevate, turn the nut (#13) counterclockwise until the fork frame elevates.
Fig. 3
Fig. 4
V1.0 2-3/4 Ton Pallet Jack 8442923
Visit www.princessauto.com for more information 9
3. Check again to see if the truck works well in the 3 control positions. If not,
repeat the steps above until the pallet jack lowers and elevates properly.
WARNING! Only use this pallet jack for loads weighing less than the rated
loading capacity. To avoid serious bodily injury or death, and/or property
damage, there is overload protection in this pallet jack. It will stop working
automatically when the load is over loading capacity.
CARE & MAINTENANCE
1. Maintain the tool with care. A tool in good condition is efficient, easier
to control and will have fewer problems.
2. Inspect the tool components periodically. Repair or replace damaged or
worn components. Only use identical replacement parts when
servicing.
3. Follow instructions for lubricating and changing accessories.
4. Keep the tool clean, dry and free from oil/grease at all times.
5. Maintain the tool’s labels and name plates. These carry important
information. If unreadable or missing, contact Princess Auto Ltd. for
replacements.
WARNING! Only qualified service personnel should repair the tool. An
improperly repaired tool may present a hazard to the user and/or others.
BLEEDING THE HYDRAULIC SYSTEM
During shipment or after an oil refill, air may become trapped in the
hydraulic system causing poor lifting performance. Follow these steps to
purge air from the system:
1. Remove the oil filler plug and fill the pump with hydraulic fluid to
full level.
2. Move the control handle to the lower position.
3. Pump several full strokes to eliminate any air in the system.
4. Check the oil filler hole and if necessary, top off the oil filler hole with
hydraulic oil.
5. Replace the oil filler plug and close the release valve.
6. Test the lift several times for proper operation before putting it into
use. After bleeding, if the ram still does not appear to be working
properly, do not use the ram until a qualified service technician has
repaired it.
8442923 2-3/4 Ton Pallet Jack V1.0
10 For technical questions call 1-800-665-8685
HYDRAULIC OIL CHANGE
Check the oil level annually by removing the oil
plug (#46) on top of the pump housing. When
changing or adding oil, fill the tank through the
oil plug hole (Fig. 5-2) to 80% capacity with
hydraulic jack oil, about 2-1/2 in. deep (Fig. 5-3) in
the pump housing (Fig. 5-1). Do not use any other
type of oil. When finished, replace oil plug.
SEAL AND O-RING REPLACEMENT FOR RAM AND
PLUNGER PISTON
1. Raise the pallet jack by pumping handle.
2. Remove spring shaft (#17). This will free the pump and handle
assembly from the pallet jack.
3. Remove the oil plug (#46), turn pump over and empty the oil into a
suitable container. Pump handle until all oil has drained. Dispose of
used hydraulic oil according to local disposal regulations.
4. Pull out plunger piston (#40) and/or ram piston (#42).
5. Remove all O-rings and seals (Fig. 6).
6. Insert new O-ring or seal one at a time
making sure to replace with the same
size that was removed.
7. Reassemble and fill the oil tank through
the oil plug hole to 80% capacity with
new hydraulic jack oil, about 2-1/2 in.
deep in pump housing (Fig. 5).
LUBRICATION
Inspect and lubricate the tool when required. Wheel bearings are sealed and
require no lubrication. The crankshaft features light oil bushings (oil lite
bushing) that also require no lubrication. Lightly oil all other moving parts.
NOTICE! NEVER use a penetrating oil to lubricate the tool. Penetrating oil
may act as a solvent that can break down the grease and cause the tool to
seize up.
Fig. 6
Fig. 5
V1.0 2-3/4 Ton Pallet Jack 8442923
Visit www.princessauto.com for more information 11
DISPOSAL
Recycle a tool damaged beyond repair at the appropriate facility.
Contact your local municipality for a list of disposal facilities or by-laws for
electronic devices, batteries, oil or other toxic liquids.
IMPORTANT! DO NOT pollute the environment by allowing uncontrolled
discharge of waste oil.
HYDRAULIC FLUID
Do not drain hydraulic oil into the sewer system or dispose in an
uncontrolled location. Hydraulic fluid may take more than a year to
breakdown in the environment and the ingredients may still be toxic.
Contact your local municipality for proper disposal instructions or locations.
TROUBLESHOOTING
Visit a Princess Auto Ltd. location for a solution if the tool does not function
properly or parts are missing. If unable to do so, have a qualified technician
service the tool.
Problem(s) Possible Cause(s) Suggested Solution(s)
Hydraulic unit
does not lift.
1. Low oil level.
2. Air in pump.
3. Worn O-ring in ram
cylinder.
1. Add enough oil.
2. See Bleeding the Hydraulic
System.
3. Replace O-ring.
Once lifted, fork
lowers by itself.
1. Air comes into the oil.
2. Worn O-ring in ram
cylinder.
3. Pallet jack loaded
beyond capacity.
4. Damaged push rods
and/or linkages
1. See Bleeding the Hydraulic
System.
2. Replace O-ring.
3. Reduce load to within
capacity.
4. Replace damaged parts.
8442923 2-3/4 Ton Pallet Jack V1.0
12 For technical questions call 1-800-665-8685
PARTS BREAKDOWN
PARTS LIST
# DESCRIPTION QTY
1
Handle Tube 1
2
Blade Spring 1
3
Spring 1
4
Elastic Pin 1
5
Control Lever 1
V1.0 2-3/4 Ton Pallet Jack 8442923
Visit www.princessauto.com for more information 13
6
Roller 1
7
Elastic Pin 2
8
Elastic Pin 2
9
Pull Rod 1
10
Pin 1
11
Chain 1
12
Adjusting Screw 1
13
Nut 1
14
Screw 3
15
Spring Washer 3
16
Pressure Frame 1
17
Spring Shaft 1
18
Shaft 1
19
Oil Lite Bushing 1
20
Pressure Roller 1
21
Elastic Pin 1
22
Release Plug 1
23
O-ring 1
24
Release Screw 1
25
Spring 1
26
Valve 1
27
Steel Ball 1
28
Oil Baffle Washer 2
29
O-ring 1
30
Valve Base 1
31
Tapered Column 1
32
Spring 1
33
Washer 1
34
Release Plug 1
35
U-packing 1
36
Dust Seal Ring 1
37
Spring 1
38
Spring Cap 1
39
E-ring 1
40
Plunger Piston 1
41
Steel Ball 1
42
Ram Piston 1
43
Dust Seal Ring 1
44
O-ring 1
45
U-packing 1
46
Oil Plug 1
47
O-ring 1
48
Pump Housing Assy 1
49
Oil Lite Bushing 2
50
Cam 1
51
Release Nozzle 1
52
O-ring 2
53
Release Nozzle Spring 1
54
Spring Pin 1
55
Spring Pin 1
56
Spring Pin 2
57
Bearing Base 1
58
Ball Bearing 1
59
Table Pin 2
60
Oiler 1
61
Snap Ring 1
62
Table 1
63
Ball Bearing 4
64
Snap Ring 2
65
Dust Seal Cap 2
66
Steering Wheel 2
67
Lifting Yoke 1
8442923 2-3/4 Ton Pallet Jack V1.0
14 For technical questions call 1-800-665-8685
68
Oil Lite Bushing 2
69
Oil Lite Bushing 2
70
Spring Pin 2
71
Oil Lite Bushing 2
72
Crank Pin 2
73
Push Rod 2
74
Crank Shaft 1
75
Spring Pin 1
76
Socket Head Cap Screw 1
77
Fork Frame 1
78
V Nut 2
79
Guide Roller 2
80
Hex Cap Screw 2
81
Spring Pin 2
82
Rod Pin 2
83
Load Wheel Axle 2
84
Flat Washer 4
85
Ball Bearing 4
86
Load Wheel 2
87
Spring Pin 2
88
Load Wheel Frame 2
89
Arm Pin 2
90
Spring Pin 2
91
Steering Wheel Axle Shaft 1
92
Hex Nut 1
93
Socket Head Cap Screw 1
V1.0 2-3/4 Ton Pallet Jack 8442923
Visit www.princessauto.com for more information 15
8442923 2-3/4 Ton Pallet Jack V1.0
16 For technical questions call 1-800-665-8685
V1,0 8442923
Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil.
Conservez ce manuel afin de pouvoir le consulter plus tard.
8442923 Transpalette à main, 2 3/4 tonnes V1,0
2 En cas de questions techniques, appelez le 1-800-665-8685
SPÉCIFICATIONS
Cap. de levage 2 3/4 tonnes
Cap. de levage 5 500 lb
Hauteur de levage min. 3 po
Hauteur de levage max. 7 1/2 po
Taille de fourche 48 po
Distance entre fourche 14 3/8 po
Rayon de braquage 230 °
Matériau Acier au carbone
Finition Revêtement en poudre
Taille de roue 7 po
Matériau de roue Nylon
Type de manche Tube en acier
Matériau de manche Acier
Dimensions 27 x 48 po
DÉFINITIONS DE DANGER
Veuillez-vous familiariser avec les avis de danger qui sont présentés dans ce
manuel. Un avis est une alerte indiquant qu'il existe un risque de dommage à la
propriété, de blessure ou de décès si on ne respecte pas certaines instructions.
DANGER ! Cet avis indique un risque immédiat et particulier qui
entraînera des blessures corporelles graves ou même la
mort si on omet de prendre les précautions nécessaires.
AVERTISSEMENT ! Cet avis indique un risque particulier ou une pratique non
sécuritaire qui
pourrait entraîner des blessures
corporelles graves ou même la mort si on omet de
prendre les précautions nécessaires.
ATTENTION ! Cet avis indique une situation possiblement dangereuse qui
peut entraîner des blessures mineures ou modérées si on
ne procède pas de la façon recommandée.
AVIS ! Cet avis indique un risque particulier ou une pratique non
sécuritaire qui entraînera des dommages au niveau de
l'équipement ou des biens, mais non des blessures
corporelles.
V1,0 Transpalette à main, 2 3/4 tonnes 8442923
Visitez www.princessauto.com pour plus d'informations 3
INTRODUCTION
Le transpalette à main a été conçu pour transporter des charges présentant une
base fixe et de niveau.
SÉCURITÉ
AVERTISSEMENT ! Veuillez lire et comprendre toutes les instructions avant
d'utiliser cet outil. L'utilisateur doit respecter les précautions de base
lorsqu'il utilise cet outil afin de réduire le risque de blessure ou de
dommage à l'équipement.
Conservez ce manuel qui contient les avertissements de sécurité, les
précautions, les instructions de fonctionnement ou d'inspection et d'entretien.
AIRE DE TRAVAIL
1. Travaillez dans un environnement de travail sécuritaire. Gardez votre
aire de travail propre, bien éclairée et exempte de toute distraction.
Placez les lampes de façon à ne pas travailler dans l’ombre.
2. Assurez-vous que les personnes qui ne portent pas l'équipement de
sécurité approprié ne se trouvent pas à proximité de l'aire de travail.
3. Rangez les outils correctement dans un lieu sécurisé et sec. Gardez les
outils hors de la portée des enfants.
SÉCURITÉ PERSONNELLE
AVERTISSEMENT ! Portez de l'équipement de protection personnelle
homologué par l'Association canadienne de normalisation (CSA) ou
l'American National Standards Institute (ANSI).
ÉQUIPEMENT DE PROTECTION PERSONNELLE
1. Portez toujours des lunettes antiprojections qui offrent une protection
frontale et latérale pour les yeux. L'équipement de protection des yeux
devrait être conforme à la norme CSA Z94.3-07 ou ANSI Z87.1 fonction
du type de travail effectué.
2. Portez des gants qui protègent en fonction des matériaux de travail et
pour réduire les effets des vibrations de l'outil.
3. Portez des vêtements de protection conçus pour l'environnement de
travail et pour l'outil.
4. Les chaussures antidérapantes sont recommandées pour maintenir la
stabilité et l'équilibre au sein de l'environnement de travail.
8442923 Transpalette à main, 2 3/4 tonnes V1,0
4 En cas de questions techniques, appelez le 1-800-665-8685
PRÉCAUTIONS PERSONNELLES
Gardez le contrôle de l'outil, de vos mouvements et de l'environnement de
travail pour éviter les blessures ou le bris de l'outil.
1. N'utilisez pas l'outil si vous êtes fatigué ou sous l'effet de drogues,
d'alcool ou de médicaments.
2. Évitez de porter des vêtements ou des bijoux pouvant se prendre dans les
pièces mobiles d'un outil. Gardez les cheveux longs recouverts ou attachés.
3. N'utilisez pas l'outil si vous devez étirer les bras pour vous en servir.
Une stabilité et un équilibre appropriés sont nécessaires afin d'avoir un
meilleur contrôle en cas de situations inattendues.
4. Tenez cet outil solidement à l’aide des deux mains. Un outil tenu d’une
seule main peut causer une perte de contrôle.
CONSIGNES DE SÉCURITÉ SPÉCIFIQUES
AVERTISSEMENT! Ne permettez PAS au confort ou à votre familiarisation avec
l'outil (obtenus après un emploi répété) de se substituer à une adhésion stricte
aux règles de sécurité de l'outil. Si vous utilisez cet outil de façon dangereuse
ou incorrecte, vous pouvez subir des blessures corporelles graves.
1. Utilisez le bon outil pour la tâche à effectuer. Cet outil a été conçu pour
une utilisation spécifique. Évitez de modifier ou d'altérer cet outil ou de
l'utiliser à une fin autre que celle pour laquelle il a été conçu.
2. N’utilisez pas l’outil si des pièces présentent des dommages ou sont
déplacées. Réparez ou remplacez les pièces.
3. Avant d’abaisser la charge, assurez-vous qu’aucune obstruction ne se
trouve en dessous et que tous les gens se trouvent à l’écart.
4. Ne laissez jamais personne monter sur le transpalette à main.
5. Utilisez celui-ci sur des planchers lisses, finis et de niveau seulement.
Ne l'utilisez pas sur des rampes ou sur des planchers inclinés.
6. Pour éviter qu'il ne bascule de façon accidentelle, assurez-vous que la
charge est centrée sur les fourches du transpalette à main.
7. Ne soulevez pas une charge uniquement avec l'extrémité des fourches.
Il pourrait en résulter des dommages au niveau des fourches et des
blessures corporelles si l'arrière du transpalette à main bascule
abruptement vers le haut.
8. Il est important que vous connaissiez le poids de la charge soulevée. Ne
dépassez pas la capacité maximale (voir Spécifications). Une surcharge
peut causer des dommages ou une faillite du cric.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
Power Fist 8442923 Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: Power Fist 8442923 Owner's manual
Documents connexes
-
Power Fist 8464216 Parts list
-
-
-
-
-
-
-
-
-
Autres documents
-
Powerfist 9001439 Le manuel du propriétaire
-
-
-
-
-
-
PROPOINT 9081613 Le manuel du propriétaire
-
-
-