Power Fist 1010010 Le manuel du propriétaire

Taper
Le manuel du propriétaire
V1.0 1010010
Please read and understand all instructions before use. Retain this manual for
future reference.
1010010 12 Ton L ow-Profile Hydraulic Bottle Jack V1.0
2 For technical questions call 1-800-665-8685
SPECIFICATIONS
Type
Low-Profile
Lift Capacity 24,000 lb (10,886 kg)
Lift Range
Total Range
7-7/16 to 13-3/4 in.
Ram Travel 11-3/8 in.
Screw Extension 2-5/16 in.
Saddle Size 1-9/16 in. diameter
Base Size 5-1/4 x 5-1/4 in.
Construction Q235 Steel and Cast Iron
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this manual. A
notice is an alert that there is a possibility of property damage, injury or
death if certain instructions are not followed.
DANGER! This notice indicates an immediate and specific hazard that
will result in severe personal injury or death if the proper
precautions are not taken.
WARNING! This notice indicates a specific hazard or unsafe practice that
could result in severe personal injury or death if the proper
precautions are not taken.
CAUTION! This notice indicates a potentially hazardous situation that may
result in minor or moderate injury if proper practices are
not taken.
NOTICE! This notice indicates that a specific hazard or unsafe practice
will result in equipment or property damage, but not
personal injury.
V1.0 12 Ton L ow-Profile Hydraulic Bottle Jack 1010010
Visit www.princessauto.com for m or e in for mati on 3
INTRODUCTION
Ideal for lifting low-profile cars, trucks, farm vehicles and machinery.
Electrostatically painted steel construction for strength, durability and
corrosion resistance. Two pc handle for easy transport and storage.
Automatic oil bypass provides safety by preventing over-pressuring of
the jack.
SAFETY
WARNING! Read and understand all instructions before using this tool. The
operator must follow basic precautions to reduce the risk of personal injury
and/or damage to the equipment.
Keep this manual for safety warnings, precautions, operating or inspection
and maintenance instructions.
WORK AREA
1. Operate in a safe work environment. Keep your work area clean, well-
lit and free of distractions. Place lights so you are not working in
a shadow.
2. Keep anyone not wearing the appropriate safety equipment away from
the work area.
3. Store tools properly in a safe and dry location. Keep tools out of the
reach of children.
PERSONAL SAFETY
WARNING! Wear personal protective equipment approved by the Canadian
Standards Association (CSA) or American National Standards
Institute (ANSI).
PERSONAL PROTECTIVE EQUIPMENT
1. Always wear impact safety goggles that provide front and side
protection for the eyes. Eye protection equipment should comply with
CSA Z94.3-07 or ANSI Z87.1 standards based on the type of
work performed.
2. Wear gloves that provide protection based on the work materials or to
reduce the effects of tool vibration.
3. Wear protective clothing designed for the work environment and tool.
4. Non-skid footwear is recommended to maintain footing and balance in
the work environment.
1010010 12 Ton L ow-Profile Hydraulic Bottle Jack V1.0
4 For technical questions call 1-800-665-8685
5. Wear steel toe footwear or steel toe caps to prevent a foot injury from
falling objects.
PERSONAL PRECAUTIONS
Control the tool, personal movement and the work environment to avoid
personal injury or damage to the tool.
1. Do not operate any tool when tired or under the influence of drugs,
alcohol or medications.
2. Avoid wearing clothes or jewelry that can become entangled with the
moving parts of a tool. Keep long hair covered or bound.
3. Do not overreach when operating the tool. Proper footing and balance
enables better control in unexpected situations.
SPECIFIC SAFETY PRECAUTIONS
WARNING! DO NOT let comfort or familiarity with product (gained from
repeated use) replace strict adherence to the tool safety rules. If you use
this tool unsafely or incorrectly, you can suffer serious personal injury.
1. Use the correct tool for the job. This tool was designed for a specific
function. Do not modify or alter this tool or use it for an
unintended purpose.
2. Do not use the tool if any parts are damaged, broken or misplaced.
Repair or replace the parts.
3. Do not overload the jack beyond its rated load capacity
(see Specifications).
4. Do not use a handle extension for the jack handle.
5. Rest the jacks base on a firm, level surface capable of sustaining the
load. Keep the surface clean and free from debris.
6. Make sure the saddle is fully positioned under the load
before operating.
7. Make sure the load is stable, so it does not shift when lifting
or lowering.
8. Make sure there is enough clearance around the jack and the load
during lifting or lowering actions.
9. Before lifting a vehicle, apply the emergency brake and block
all wheels.
V1.0 12 Ton L ow-Profile Hydraulic Bottle Jack 1010010
Visit www.princessauto.com for m or e in for mati on 5
10. Support the load with jack stands or a support structure of adequate
capacity immediately after lifting. Never work under a load without
additional support devices.
11. The jack must remain in a static position for lifting and lowering loads.
Never move a load that is elevated on the jack. Ensure the load remains
stable at all times.
12. Do not push a load off the jack; lower carefully.
13. Before lowering load, ensure that there are no obstructions underneath
and that all people are standing clear.
14. Do not place your hands between the moving components.
15. Never allow load to tilt on the jack as the jack may kick out causing
injury to the operator and/or cause the load to fall.
16. DO NOT use the jack if damaged or it was subjected to a dynamic shock
load. This is a sudden and unexpected load or force applied to the jack.
Have the jack inspected and repaired by a qualified service technician.
HYDRAULIC PRECAUTIONS
DANGER! Seek immediate medical attention if hydraulic fluid under
pressure penetrates your skin. See Injection Injury precautions for
instructions before using a pressurized hydraulic system.
1. Do not touch or handle hydraulic hoses or components while under
pressure. Hydraulic fluid escaping under pressure has sufficient force to
penetrate your clothing and skin. A pinpoint hole may inject hydraulic fluid
into your body. Seek immediate medical attention if this occurs (see
Injection Injury).
2. Do not adjust the hydraulic systems relief setting. The settings are
preset by the factory.
3. Hydraulic oil under pressure is hot and can cause a burn injury if
touched, sprayed or spilled. Allow the hydraulic system to cool before
conducting maintenance.
4. Hydraulic components require regular inspection. Release all pressure
from the system before you inspect it. Replace damaged hydraulic
parts with identical manufacturer's components.
5. Do not attempt makeshift repairs to a hydraulic system. Such repairs can
fail suddenly and create a hazardous condition.
1010010 12 Ton L ow-Profile Hydraulic Bottle Jack V1.0
6 For technical questions call 1-800-665-8685
6. Hydraulic fluid has a combustible flash point of 200°F (93°F). Do not
expose the fluid to an ignition source.
7. Change your clothing immediately if sprayed with hydraulic fluid. Store
clothing or rags contaminated with hydraulic fluid in an approved
metal safety can with a spring-closing lid and venting designed to
contain a fire.
8. Only use hydraulic fluid in the pump. Do not substitute or mix brake
fluid, or any other fluid, with the hydraulic fluid. This can result in a
pump failure and injure the user or bystander. It may also damage
the pump.
INJECTION INJURY
DANGER! Seek immediate, professional medical treatment if fluid
penetrates your skin. It may feel like a pricking or sting. Do not wait for the
appearance of symptoms. A toxic reaction can occur from the exposure.
Delay in treatment can lead to amputation or death.
Inform the medical staff that you have a fluid penetration injury as soon as
you arrive at the medical facility. The severity of the symptoms will depend
on the type of fluid injected. Bring the Safety Data Sheet for the fluid with
you to the medical facility if possible.
INJECTION PRECAUTIONS
Fluid can penetrate the skin at 100 PSI pressure. Fluid escaping under
pressure from the tool has sufficient force to penetrate your clothing and
skin. Follow the precautions below to avoid an injection injury.
1. Always check for leaks wearing a face shield, safety goggles,
rubberized gloves and protective clothes.
2. Release all pressure from the system before you inspect it.
3. Do not use your hands to detect a fluid leak. Use a large piece of wood,
cardboard or paper and watch for discolouration.
4. Replace damaged parts with identical manufacturer's components to
ensure it is rated to handle the pressure.
UNPACKING
WARNING! Do not operate the tool if any part is missing. Replace the
missing part before operating. Failure to do so could result in a malfunction
and personal injury.
V1.0 12 Ton L ow-Profile Hydraulic Bottle Jack 1010010
Visit www.princessauto.com for m or e in for mati on 7
Remove the parts and accessories from the packaging and inspect for damage.
Make sure that all items in the contents are included.
Contents:
Bottle Jack
2 Piece Handle
IDENTIFICATION KEY
A Ram E Saddle
B Oil Plug F Ex t ens io n Scr ew
C Release Valve G Handle Sleeve
D Handle Assembly
OPERATION
Letter references in parenthesis (A) refer to
the included Identification Key.
RAISING A LOAD
WARNING! Do not place any part of your body under the load without jack
stands in place. The bottle jack is not designed to maintain heavy loads for
long periods of time.
1. Place the jack on a hard level surface capable of handling the load.
2. Assemble the handle. The spring clips must align with the slots.
3. Close the release valve (C). Insert the end of the handle (D) over the valve
and twist to the right.
4. Insert the handle into the handle sleeve (G).
5. Pump to raise the ram. Stop just before the ram contacts the loads lift
point. Inspect the rams position and adjust if necessary.
6. Twist the saddle counterclockwise to extend the screw until it touches
the load.
7. Pump slowly until the ram is supporting the load. Continue to pump as
normal to lift the load to the desired height.
8. Position supports like jack stands if the load will remain off the ground
for an extended period. Consult the manual for the support device for
proper placement.
1010010 12 Ton L ow-Profile Hydraulic Bottle Jack V1.0
8 For technical questions call 1-800-665-8685
LOWERING A LOAD
WARNING! Dynamic shock loads are created by quick opening and closing of
the release valve when lowering the load. The resulting overload may cause
the hydraulic system to fail, which could result in severe personal injury
and/or property damage.
WARNING! Before lowering the load or vehicle, ensure that there are no
obstructions underneath and that all people are standing clear.
1. Insert the handle end over the release valve.
2. Open the valve by gradually twisting to the left.
3. The load will begin to lower as air escapes through the valve.
4. Twist right to slow and left to increase the rate of descent.
5. Remove the jack once the load is on the ground or on a support
mechanism like jack stands.
6. The ram should fully retract. If it does not, push down on it until it
is seated.
7. Turn the screw clockwise to retract the screw until the saddle
is seated.
RAISING AND LOWERING A VEHICLE
Take these additional steps before following instructions in
Raising a Load
and
Lowering a Load
.
1. Set the vehicle in parking gear and engage the parking brake.
a. For vehicles with a manual transmission, engage the parking brake
and leave the car in reverse or first gear. Consult your vehicle owners
manual for the correct gear.
2. Place wheel chocks that fit the wheel curve on either side of the
vehicles remaining wheels.
3. Place the jack only on support points or areas specified by the vehicle
manufacturer (consult owner’s manual).
4. Lift the vehicle to a height that leaves enough room to place the
jack stands.
5. When the work is done, raise the load enough with the jack to
carefully remove the jack stands.
6. Slowly and carefully lower the load.
V1.0 12 Ton L ow-Profile Hydraulic Bottle Jack 1010010
Visit www.princessauto.com for m or e in for mati on 9
CARE & MAINTENANCE
1. Maintain the tool with care. A tool in good condition is efficient, easier
to control and will have fewer problems.
2. Inspect the tool components periodically. Repair or replace damaged or
worn components. Only use identical replacement parts
when servicing.
3. Follow instructions for lubricating and changing accessories.
4. Keep the tool handles clean, dry and free from oil/grease at all times.
5. Maintain the tools labels and name plates. These carry important
information. If unreadable or missing, contact Princess Auto Ltd.
for replacements.
6. Have a qualified technician inspect the jack:
a. Once a year.
b. After receiving a shock load. Take the jack out of service until the
technician certifies that it is safe to use.
WARNING! Only qualified service personnel should repair the tool. An
improperly repaired tool may present a hazard to the user and/or others.
HYDRAULIC RAM MAINTENANCE
Monthly maintenance is recommended for the hydraulic ram. Any restrictions
due to dirt, rust, etc. can cause the either slow movement or extremely rapid
jerks, damaging the internal components. The following steps are designed t o
keep the pump maintained and operational.
1. Lubricate the cylinder and the pumping mechanism with light oil.
2. Visually inspect for cracked welds, bent, loose, missing parts or hydraulic
oil leaks.
3. Check and maintain the ram oil level.
4. Always store the hydraulic ram in the fully retracted position. This will
help protect critical areas from corrosion.
5. Do not use brake or transmission fluids or regular motor oil, as they
can damage the seals. Always purchase and use products labeled
hydraulic jack oil.
6. Remove any hydraulic pump from service that is damaged, worn down or
operates abnormally, until repaired by an authorized service technician.
1010010 12 Ton L ow-Profile Hydraulic Bottle Jack V1.0
10 For technical questions call 1-800-665-8685
REPLACING THE HYDRAULIC JACK OIL
Replace the jack oil annually.
1. Lower the ram and remove the oil plug.
2. Lay the jack on its side and drain the oil into a suitable container.
Dispose of used hydraulic oil in accordance with local by-laws.
3. Stand the jack on its base and wipe off any excess oil.
4. Fill the cylinder with a high quality hydraulic jack oil, up to the oil
plug opening.
5. Follow the steps in Bleeding the Hydraulic System.
BLEEDING THE HYDRAULIC SYSTEM
Bleed excess air from the hydraulic system as follows:
1. Open the release valve by turning it counterclockwise.
2. Remove the oil plug (B) and fill the pump with hydraulic fluid.
3. Wait 5 minutes for trapped air to rise to the surface.
4. Pump the handle for several full strokes to eliminate any air in the system.
5. Check the oil filler hole and if necessary, top off with more hydraulic oil.
6. Restore the oil filler screw. Close the release valve by turning
clockwise.
7. Test the ram several times for proper operation before putting it into use.
Do not use the ram if it still does not appear to be working properly. Have
a qualified technician repair the hydraulic system.
FLUSHING THE VALVE
Contaminants may block the release valve, causing issues when
attempting to lower a load. Clear the valve with the following steps.
1. Lower the saddle and securely close the release valve.
2. Manually lift the saddle several inches.
3. Open the release valve and force the saddle down as quickly as possible.
CLEANING
Clean the tool with a clean rag and a degreasing solvent. Lubricate
moving contact points after cleaning to ensure binding does not occur.
V1.0 12 Ton L ow-Profile Hydraulic Bottle Jack 1010010
Visit www.princessauto.com for m or e in for mati on 11
LUBRICATION
Inspect and lubricate the tool when required. Only use light oil to lubricate
the tool. Other lubricants may not be suitable and could damage the tool or
cause a malfunction during use.
STORAGE
Lower the ram to its lowest position. Apply a thin coat of lubricant to the
steel parts to avoid rust. Remove the lubricant before using the tool again.
DISPOSAL
Recycle a tool damaged beyond repair at the appropriate facility.
Contact your local municipality for a list of disposal facilities or by-laws for
electronic devices, batteries, oil or other toxic liquids.
IMPORTANT! DO NOT pollute the environment by allowing uncontrolled
discharge of waste oil.
HYDRAULIC FLUID
Do not drain hydraulic oil into the sewer system or dispose in an
uncontrolled location. Hydraulic fluid may take more than a year to
breakdown in the environment and the ingredients may still be toxic.
Contact your local municipality for proper disposal instructions or locations.
TROUBLESHOOTING
Visit a Princess Auto Ltd. location for a solution if the tool does not function
properly or parts are missing. If unable to do so, have a qualified technician
service the tool.
Problem(s)
Possible
Cause(s)
Suggested Solution(s)
Jack will not lift
load.
1. The release valve is not
closed tightly.
2. Overloaded the jack.
3. Air supply is inadequate.
4. Air is trapped in the
hydraulic system.
1. Close the release valve firmly.
2. Reduce load or use a jack with a
greater lift capacity.
3. Ensure ad equate air su pply.
4. Bleed air from the system.
1010010 12 Ton L ow-Profile Hydraulic Bottle Jack V1.0
12 For technical questions call 1-800-665-8685
Jack will lift, but
will not maintain
pressure.
1.
Release valve is not closed
tightly.
2. Overloaded the jack.
3. Hydraulic unit is
malfunctioning.
1. Close the release valve firmly.
2. Reduce load or use a jack with a
greater lift capa city.
3. a. Replace the seals.
b. Have service technician repair
the jack.
Will not lower
after loading.
1. Reservoir is overfilled.
2. Linkages are binding.
3. Contaminated release
valve.
1. Dr ain oil to th e proper level.
2. Clean and lubricate all moving
parts.
3. See Care & Maintenance -
Flushing
th e Valve
Poor lift
performance.
1. Hydraulic oil level is low.
2. Air is trapped in the
hydraulic system.
1. Add oil to the proper level.
2. Bleed air from the system.
Will not lift to the
m a x. h ei ght.
1. Air is trapped in the
system.
2. Hydraulic oil level is too
low.
1. Bleed air from th e sy stem.
2. Add oil to the proper level.
V1,0 1010010
Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil.
Conservez ce manuel afin de pouvoir le consulter plus tard.
1010010 Cric-bouteille hydraulique à profil bas, 12 tonnes V1,0
2 En cas de questions techniques, appelez le 1-800-665-8685
SPÉCIFICATIONS
Type Profil bas
Capaci de levage
10 886 kg (24 000 lb)
Plage de levage
Échelle totale
7 7/16 à 13 3/4 po
Course du rin 11 3/8 po
Rallonge de vis 2 5/16 po
Taille de selle Diamètre de 1 9/16 po
Dimensions de la base 5 1/4 x 5 1/4 po
Construction
Construction en acier et
fonte Q235
FINITIONS DE DANGER
Veuillez-vous familiariser avec les avis de danger qui sont présentés dans ce
manuel. Un avis est une alerte indiquant qu'il existe un risque de dommage
à la propriété, de blessure ou de décès si on ne respecte pas
certaines instructions.
DANGER ! Cet avis indique un risque immédiat et particulier qui
entraînera des blessures corporelles graves ou même la
mort si on omet de prendre les précautions nécessaires.
AVERTISSEMENT ! Cet avis indique un risque particulier ou une pratique non
sécuritaire qui
pourrait entraîner des blessures
corporelles graves ou même la mort si on omet de
prendre les précautions nécessaires.
ATTENTION ! Cet avis indique une situation possiblement dangereuse qui
peut entraîner des blessures mineures ou modérées si on
ne procède pas de la façon recommandée.
AVIS ! Cet avis indique un risque particulier ou une pratique non
sécuritaire qui entraînera des dommages au niveau de
l'équipement ou des biens, mais non des
blessures corporelles.
V1,0 Cric-bouteille hydraulique à profil bas, 12 tonnes 1010010
Visitez www.princessauto. c om pour plu s d 'in form ation s 3
INTRODUCTION
Idéal pour lever des voitures, des camions, des véhicules agricoles et de la
machinerie à profil bas. Construction en acier avec peinture électrostatique
qui assure une robustesse, une durabilité et une résistance à la corrosion.
Poignée en 2 pièces pour faciliter le transport et le rangement. Dérivation
d’huile automatique de sécurité pour prévenir la surpression du cric.
SÉCURI
AVERTISSEMENT ! Veuillez lire et comprendre toutes les instructions avant
d'utiliser cet outil. L'utilisateur doit respecter les précautions de base
lorsqu'il utilise cet outil afin de réduire le risque de blessure ou de
dommage à l'équipement.
Conservez ce manuel qui contient les avertissements de sécurité, les
précautions, les instructions de fonctionnement ou d'inspection et d'entretien.
AIRE DE TRAVAIL
1. Travaillez dans un environnement de travail sécuritaire. Gardez votre
aire de travail propre, bien éclairée et exempte de toute distraction.
Placez les lampes de façon à ne pas travailler dans lombre.
2. Assurez-vous que les personnes qui ne portent pas l'équipement de
sécurité approprne se trouvent pas à proximité de l'aire de travail.
3. Rangez les outils correctement dans un lieu sécurisé et sec. Gardez les
outils hors de la portée des enfants.
SÉCURITÉ PERSONNELLE
AVERTISSEMENT ! Portez de l'équipement de protection personnelle
homologué par l'Association canadienne de normalisation (CSA) ou
l'American National Standards Institute (ANSI).
ÉQUIPEMENT DE PROTECTION PERSONNELLE
1. Portez toujours des lunettes antiprojections qui offrent une protection
frontale et latérale pour les yeux. L'équipement de protection des yeux
devrait être conforme à la norme CSA Z94.3-07 ou ANSI Z87.1 fonction du
type de travail effectué.
2. Portez des gants qui protègent en fonction des matériaux de travail et
pour réduire les effets des vibrations de l'outil.
1010010 Cric-bouteille hydraulique à profil bas, 12 tonnes V1,0
4 En cas de questions techniques, appelez le 1-800-665-8685
3. Portez des vêtements de protection conçus pour l'environnement de
travail et pour l'outil.
4. Les chaussures antidérapantes sont recommandées pour maintenir la
stabilité et l'équilibre au sein de l'environnement de travail.
5. Portez des chaussures à embout d'acier ou à coquilles d'acier pour éviter
les blessures aux pieds dues à la chute d'objets.
PRÉCAUTIONS PERSONNELLES
Gardez le contrôle de l'outil, de vos mouvements et de l'environnement de
travail pour éviter les blessures ou le bris de l'outil.
1. N'utilisez pas l'outil si vous êtes fatigué ou sous l'effet de drogues,
d'alcool ou de médicaments.
2. Évitez de porter des vêtements ou des bijoux pouvant se prendre dans
les pièces mobiles d'un outil. Gardez les cheveux longs recouverts
ou attacs.
3. N'utilisez pas l'outil si vous devez étirer les bras pour vous en servir.
Une stabilité et un équilibre appropriés sont nécessaires afin d'avoir un
meilleur contrôle en cas de situations inattendues.
CONSIGNES DE SÉCURITÉ SPÉCIFIQUES
AVERTISSEMENT ! Ne permettez PAS au confort ou à votre familiarisation avec
l'outil (obtenus après un emploi répété) de se substituer à une adhésion
stricte aux règles de sécurité de l'outil. Si vous utilisez cet outil de façon
dangereuse ou incorrecte, vous pouvez subir des blessures
corporelles graves.
1. Utilisez le bon outil pour la tâche à effectuer. Cet outil a été conçu pour
une utilisation spécifique. Évitez de modifier ou d'altérer cet outil ou de
l'utiliser à une fin autre que celle pour laquelle il a été conçu.
2. N’utilisez pas loutil si des pièces présentent des dommages ou sont
déplacées. Réparez ou remplacez les pièces.
3. Ne surchargez pas les chandelles au-delà de leur capacité de charge
nominale (consultez Spécifications).
4. N’utilisez pas de rallonge sur la poignée du cric.
5. Déposez la base du cric sur une surface solide et de niveau pouvant
soutenir la charge. Gardez la surface propre et exempte de débris.
V1,0 Cric-bouteille hydraulique à profil bas, 12 tonnes 1010010
Visitez www.princessauto. c om pour plu s d 'in form ation s 5
6. Assurez-vous que la douille est correctement placée sous la charge avant
de mettre en marche.
7. Assurez-vous que la charge est stable pour éviter quelle se déplace durant
le levage ou la descente.
8. Assurez-vous quil existe un espace suffisant autour du cric et de la charge
durant le levage ou la descente.
9. Avant de soulever un véhicule, appliquez le frein d'urgence et bloquez
toutes les roues.
10. Appuyez la charge sur des chandelles ou sur une structure dappui de
capacité suffisante immédiatement après la consult é soulevée. Ne
travaillez jamais sous une charge sans appareils dappui additionnels.
11. Le cric doit rester en position immobile afin de pou consultez soulever et
abaisser des charges. Ne déplacez jamais une charge soulevée sur un cric.
Assurez-vous que la charge demeure stable en tout temps.
12. Ne poussez pas la charge hors du cric; abaissez-la doucement.
13. Avant d'abaisser la charge, assurez-vous qu'aucune obstruction ne se
trouve en dessous et que tous les gens se trouvent à l'écart.
14. Ne placez pas vos mains entre les composants mobiles.
15. Ne laissez jamais la charge sincliner sur le cric car le cric pourrait céder
et causer des blessures à lopérateur et/ou causer la chute de la charge.
16. N’utilisez PAS le cric sil est endommagé ou sil a subi un choc
dynamique. Il sagit là dune charge ou dune force soudaine et
inattendue qui est appliquée au niveau du cric. Faites vérifier et
réparer le cric par un technicien de service compétent.
CURITÉ HYDRAULIQUE
DANGER ! Contactez immédiatement un médecin si le liquide hydraulique
sous pression vous pénètre la peau. Consultez la rubrique Instructions en
cas de blessures par injection pour connaître la marche à suivre avant
d’utiliser un système hydraulique sous pression.
1. Ne touchez pas et ne manipulez pas les tuyaux hydrauliques ou les
composants sous pression. Une fuite de liquide hydraulique sous pression
peut avoir une force suffisante pour pénétrer la peau. Un trou d'aiguille peut
projeter du liquide hydraulique dans votre corps. Appelez immédiatement
un médecin dans un tel cas (voir Blessure Par Injection).
1010010 Cric-bouteille hydraulique à profil bas, 12 tonnes V1,0
6 En cas de questions techniques, appelez le 1-800-665-8685
2. Ne réglez pas les ajustements de détente du système hydraulique. Les
réglages sont effectués au préalable en usine.
3. L’huile hydraulique sous pression est chaude et peut causer des
blessures par brûlure en cas de contact, de pulvérisation ou de
déversement. Laissez le système hydraulique refroidir avant de
procéder à lentretien.
4. Les composants hydrauliques doivent faire l'objet d'une inspection
régulière. Libérez toute la pression du système avant de procéder à son
inspection. Remplacez les pièces hydrauliques endommagées par des
composants provenant du me fabricant.
5. N'essayez pas de faire des réparations de fortune à un système
hydraulique. De telles réparations peuvent être sujettes à des
défaillances soudaines et causer une condition dangereuse.
6. Le liquide hydraulique présente un point d'inflammabilité de
93 °C (200 °F). N'exposez le liquide à aucune source d'allumage.
7. Changez immédiatement vos vêtements s'ils ont été arrosés avec le
liquide hydraulique. Rangez les vêtements ou les chiffons contaminés
par le liquide hydraulique dans une boîte de sécurité en métal
approuvée munie d'un couvercle à ressort et d'un dispositif de mise à
l'air libre capable de contenir un incendie.
8. Utilisez uniquement du liquide hydraulique dans la pompe. Ne
remplacez pas ou ne mélangez pas le liquide ou tout autre liquide avec
le liquide hydraulique. Il pourrait en résulter le bris de la pompe et des
blessures pour lutilisateur et les gens à proximité. La pompe pourrait
également subir des dommages.
BLESSURE PAR INJECTION
DANGER ! Demandez immédiatement un traitement médical par un
professionnel si le liquide hydraulique pénètre votre peau. Vous pourriez
ressentir une sensation de piqûre ou d'élancement. N'attendez pas que des
symptômes apparaissent. Une exposition peut entraîner une réaction toxique.
Tout délai dans le traitement pourrait entraîner l'amputation ou la mort.
Avisez le personnel médical que vous avez subi une pénétration de liquide
hydraulique dès que vous arrivez à l'installation médicale. La gravité des
symptômes dépendra du type de liquide injecté. Apportez la fiche
signalétique du liquide lorsque vous vous rendez à l'installation médicale.
V1,0 Cric-bouteille hydraulique à profil bas, 12 tonnes 1010010
Visitez www.princessauto. c om pour plu s d 'in form ation s 7
PRÉCAUTIONS EN CAS D'INJECTION
Le liquide peut pénétrer dans la peau à une pression de 100 lb/po carré. Une
fuite de liquide hydraulique sous pression peut avoir une force suffisante
pour pénétrer la peau. Observez les précautions énoncées ci-dessous pour
éviter toute blessure provoquée par injection.
1. Vérifiez toujours sil y a des fuites en portant un écran facial, des
lunettes de sécurité, des gants caoutchoutés et des vêtements
de protection.
2. Libérez toute la pression du système avant de procéder à
son inspection.
3. N'utilisez pas les mains pour détecter s'il y a une fuite de liquide.
Surveillez toute décoloration sur un gros bout de bois, de carton ou
de papier.
4. Remplacez les pièces endommagées par des composants identiques du
fabricant pour vous assurer qu'il est certifié pour subir la pression.
DÉBALLAGE
AVERTISSEMENT ! Ne faites pas fonctionner l'outil si des pièces sont
manquantes. Remplacez les pièces manquantes avant l'utilisation. Le non-
respect de cet avertissement peut entraîner une défectuosité et des
blessures graves.
Retirez les pièces et les accessoires de l'emballage et vérifiez s'il y a des
dommages. Assurez-vous que tous les articles du contenu sont présents.
Contenu :
Cric-bouteille
Poignée en 2 pièces
1010010 Cric-bouteille hydraulique à profil bas, 12 tonnes V1,0
8 En cas de questions techniques, appelez le 1-800-665-8685
GUIDE DIDENTIFICATION
A Vérin
B Bouchon dhuile
C Valve de purge
D Ensemble de la poignée
E Selle
F Vis de rallonge
G Gaine de poignée
UTILISATION
Les lettres de référence entre
parenthèses (A) se rapportent à la c
d'identification co mprise.
LEVAGE DUNE CHARGE
AVERTISSEMENT ! Ne placez jamais une partie de votre corps sous la charge
avant que les chandelles naient été placées. Le cric-bouteille nest pas
conçu pour soutenir de lourdes charges pendant de longues périodes.
1. Placez le cric sur une surface dure et de niveau pouvant soutenir
la charge.
2. Assemblez la poignée. Les agrafes à ressort doivent être alignées avec
les fentes.
3. Fermez la valve de purge (C). Insérez lextrémité de la poignée (D) sur la
soupape et tournez vers la droite.
4. Insérez la poignée dans la gaine de poignée (G).
5. Pompez pour soulever le vérin. Arrêtez immédiatement avant que le
vérin ne vienne en contact avec le point de levage de la charge. Vérifiez
la position du vérin et ajustez-la, au besoin.
6. Tournez la selle dans le sens antihoraire pour déployer la vis jusquà ce
quelle entre en contact avec la charge.
7. Pompez lentement jusquà ce que le vérin soutienne la charge.
Continuez de pomper normalement pour soulever la charge à la
hauteur désirée.
1 / 1

Power Fist 1010010 Le manuel du propriétaire

Taper
Le manuel du propriétaire

dans d''autres langues