NewAge Products 52582 Guide d'installation

Pro 3.0 Series

Warning: Excessive weight hazard!

Use two or more people to move, assemble or install cabinets and locker to avoid back injury.

Do not leave children unattended near cabinets. High risk of tipping if cabinets are installed

incorrectly: securely attach cabinets to the wall to avoid serious injury.

For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at [email protected]

PRO3.INSTALL.REV.03

2

INDEX

Index - 2

Guidelines and weight capacity - 2-3

Parts list - 4

Tools needed - 5

Warranty - 5

Attaching feet - 6

Attaching casters - 7

Removing and inserting drawers - 8

Installing corner cabinet - 9

Stacking cabinets - 10

Installing worktop support bracket - 11

Attaching worktop( on 2 cabinets) - 12

Installing closet rod -13

Installing shelves - 14

Securing cabinets to drywall/stud wall -15

Hanging cabinets on stud wall - 16-19

Hanging cabinets on slatwall - 20-21

Fastening cabinets together - 22

Attaching light valance - 23

Utility hole - 24

500 lbs.

100 lbs.

300 lbs.

200 lbs.

Lockers

Max 1000 lbs.

Tool Cabinets

Max 1000 lbs.

Wall Cabinets

Max 200 lbs.

100 lbs.

600 lbs.

300 lbs.

84” Worktop. Fits over 3 Cabinets

56” Worktop. Fits over 2 Cabinets

24” Corner Worktop

Worktop

Weight

Capacity

Base Cabinets

Max 1000 lbs.

100 lbs.

200 lbs.

Split Cabinets

Max 1000 lbs.

600 lbs.

100 lbs.

100

lbs.

200 lbs.

5 lbs.

300 lbs.

Unpacking

• Begin by placing the package on a covered at surface.

• Remove all cardboard, foam packaging material and clear plastic bags.

• Dispose / recycle all packaging materials.

• Verify all the contents in the box and gather the required tools. See “Parts Supplied” and “Tools Needed” on pages 4 and 5

3

500

lbs.

100 lbs.

300

lbs.

200

lbs.

Lockers

Max 1000 lbs.

Tool Cabinets

Max 1000 lbs.

Wall Cabinets

Max 200 lbs.

100

lbs.

600 lbs.

300

lbs.

84” Worktop. Fits over 3 Cabinets

56” Worktop. Fits over 2 Cabinets

24” Corner Worktop

Worktop

Weight

Capacity

Base Cabinets

Max 1000 lbs.

100

lbs.

100

lbs.

100

lbs.

100

lbs.

100

lbs.

200

lbs.

Split Cabinets

Max 1000 lbs.

600 lbs.

100

lbs.

100

lbs.

200

lbs.

5

lbs.

300

lbs.

300

lbs.

300

lbs.

4

Mul-use Locker Sports Locker Two-Door Base Five-Drawer Tool Mulfuncon Wall Corner Wall

Hardware Box 1 1 1 1 1 1 1

#8 x 5/8" Wood Screw 2 2 4 4 4 0 4

1/4" x 0.9" Fender Washer 4 4 4 4 4 4 6

1/4" ID x 1/2" OD Washer 26 26 12 12 12 12 22

1/4" Lock Nut 10 10 4 4 4 4 4

1/4" x 2.5" Wall Screw 8 8 8 8 8 8 12

1/4"-20 x 5/8" Hex Bolts 10 10 4 4 4 4 8

Light Valence Bolts 0 0 0 0 0 2 2

Light Valence Nuts 0 0 0 0 0 2 2

Plasc Hole Caps 16 16 0 0 0 8 0

Power Cord Hole Rubber Grommet 1 1 1 0 0 0 0

She

lf Clips 24 24 0 0 0 6 0

Keys 2 2 2 2 2 2 2

Foot Aachment Screws 16 16 16 16 16 0 0

Adjustable Leveling Legs 4 4 4 4 4 0 0

Adjustable Steel Shelves 4 4 0 0 0

Closet Rod 1 1 0 0 0 0 0

Closet Rod Brackets with Rubber Coated Hooks 2 2 0 0 0 0 0

EVA Foam Drawer Liners 0 0 1 5 3 0 0

Garbage Bin 0 0 0 0 1 0 0

Parts Bins 0 0 0 0 24 0 0

Light Valence 0 0 0 0 0 1 1

Long Drawer Dividers 0 0 0 4 0 0 0

Short Drawer Dividers 0 0 0 8 0 0 0

Side Support Brackets 0 0 0 0 0 0 2

Easy Wall Hanging Brackets 2 2 2 2 2 2 3

1 0

NewAge Logo 1 1 0 0 0 0 0

Parts Supplied

Height-Adjustable

Steel Leveling Legs

Key

Washer

(1/4”x1/2”)

Wood Screw

(#8 x 5/8”)

Rubber

Grommet

Drawer Dividers

Wall Bracket Shelf Clips

Wall Screw

(1/4” x 2.5”)

Hex Bolt

(1/4” x 5/8”)

Full Width

Adjustable

Shelves

Clothes

Rod and

Hooks

Light Valence

Nut (M5)

Light Valence

Bolt (M5 x 12mm)

Support BracketLight Valance

Foot

Attachment

Screws

Lock Nut

(1/4”)

Fender Washer

(1/4”x0.9-in)

NewAge Logo

5

Tools Needed

1 x 12” Magnetic Leveler

1 x #2 Phillips Bit

1 x Tape Measure

1 x 7/16” socket

1 x Cordless Power Drill

1 x Stud Finder

1 x Pencil1 x Set

Square

1 x Hammer Drill 1 x Masonry Bit

1 x Adjustable wrench

1 x 7/16” Socket driver

wrench

1 x 8mm” Socket driver

wrench

1 x #2 Phillips

head screw driver

1 x #3 Phillips

head screw driver

[optional for masonry]

1

1 2 3

2

3

Manufacturer Warranty Limited Lifetime

1. Service calls to correct the installation of any NewAge products or to instruct you how to use or install them.

2. Damage resulting from improper handling or shipping of products, or products damaged by accident, misuse, abuse, re,

ood, improper installation, acts of God, neglect, corrosion, modication or mishandling.

3. Products damaged by improperly loading beyond the specied maximum weight capacity outlined in the instructions provided

with the product.

4. Repairs or replacement when your product is used in other than normal, single-family household use, such as a commercial

environment, or handled in anyway inconsistent with the installation instructions included with the product.

5. Cosmetic damage, including scratches, dings, dents or cracks in paint that do not aect the structural or functional capability

of the product.

6. Surfaces damaged due to chemical interaction resulting in corrosion of paint or metal.

7. Replacement parts for NewAge products outside Canada and the United States.

8. Replacement keys or locking mechanisms.

9. Loss of product contents due to theft, re, ood, accident or acts of God.

10. Shipping or freight fees to deliver replacement products or to return defective products.

11. Any labor costs during the limited warranty period.

When this product is installed, operated and maintained according to the instructions attached to or furnished with the product,

NewAge Products Inc. will replace the defective product or parts if the part fails as a result of defective materials or workmanship

for the Lifetime of the product.

NEWAGE PRODUCTS INC. WILL NOT PAY FOR:

IMPLIED WARRANTIES, INCLUDING TO THE EXTENT APPLICABLE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE, ARE EXCLUDED TO THE EXTENT LEGALLY PERMISSIBLE. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED

TO ONE YEAR, OR THE SHORTEST PERIOD ALLOWED BY LAW. SOME STATES AND PROVINCES DO NOT ALLOW LIMITATIONS OR EXCLUSIONS

ON HOW LONG AN IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT

APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE

TO STATE OR PROVINCE TO PROVINCE

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

6

Installing the Feet

1

Flip cabinet upside down,

locate holes at corners.

2

Stand & level feet.

Open cabinet, remove any shelves

or loose items.

Repeat step 3 for each corner.

5

4

Parts Needed.

16 X Foot

Attachment Screws

Align foot with edge of cabinet. Screw

in 4 x foot attachment screws using #3

Phillips Bit

3

Height-Adjustable

Steel Leveling Legs

7

Installing Casters

1

Flip cabinet upside down,

locate holes forming a square.

2

Open cabinet, remove any shelves

or loose items.

Repeat step 3 for each corner.

4

Parts Needed.

Align foot with holes. Attach with 4 hex

bolts, washers, and nuts.

3

16 X Lock Nut

(1/4”)

16 X

Washer

(1/4”)

16 X Hex Bolt

(1/4” x 5/8”)

4 x Casters

Note: Caster kits sold separately.

shopnewage.com

8

Right Side

Left Side

Slide In

Slide Out

Align Rails

Inserting Drawers.

Removing Drawers.

Installing the Drawers

Slide drawer out completely

9

Slide in corner and attach

remaining cabinets.

Installing Corner Worktop

1

Attach top to one cabinet using 1/4” x

5/8 hex bolts, nuts, and washers.

Attach second cabinet to top.

2

6”

or

4”

6”

or

4”

On adjacent edges attach 2 support

brackets to underside of corner top

using the supplied (4) 38 x 5/8” screws.

Parts Needed.

3

4x Washer

(1/4”)

4x # 8 x 5/8”

screw

4x 1/4” x 5/8

hex bolt

4x Lock Nut

(1/4”)

4

1

1 2 3

2

3

Note: Ensure there is enough assembly

room. Cabinets must be assembled away

from corner to access backs of cabinets.

X2

Important: For mounting top ush with back of

cabinet measure 6” in from corner, for mounting

top ush with front of cabinet measure 4” in from

corner and ush with edge.

2x Support

Bracket

1x Corner

Worktop

10

Stacking Cabinets

1

Locate punch holes on adjoining

surface and insert bolts.

Tighten all bolts

2

Attach cabinets using the supplied

1/4” x 5/8” hex bolts, washers, and

nuts.

Position a second base cabinet on

top of an existing base cabinet.

3

I

Parts Needed.

4 X Lock Nut

(1/4”)

8 X

Washer

(1/4”)

4 X Hex Bolt

(1/4” x 5/8”)

4

11

Installing Worktop

Side Support Bracket

Note: Support bracket included with locker.

X2

Fasten nuts, bolts, and lock washers.

2

Tighten nuts & bolts.

Parts Needed.

4

3

5

Align bracket.

Level bracket and ensure it is at the

same height as the base cabinet.

1

Open locker and locate holes on either side.

2 X Lock Nut

(1/4”)

4 X

Washer

(1/4”)

2 X Hex Bolt

(1/4” x 5/8”)

1x Support

Bracket

12

Mounting the Worktop (On 2 Cabinets)

1

Optional: For locker support bracket.

X4 X2

X2

Locate 2 punch holes both sides.

2

Drill into the worktop using the #8 x 5/8” wood screwes.

X2

Use 2 washers & #8 x 5/8” wood screws.

Provided in the locker packaging.

Place worktop on cabinets.

3

I

13

Inserting Locker Utility Rod and Hangars

1

Ensure rear ange slides down behind

clips and that the bracket is secure.

Place hangar against locker wall

above supports.

2

Open cabinet Doors. Insert clips into slots in corners.

Rotate to engage.

4

3

5

6

Interior

Side View

Interior

Side View

Lower rod into cradle.

14

Inserting Cabinet Shelves

1

Lower shelf onto supports.Insert shelf on a angle and rotate

to level position.

Insert shelf clip on slight angle

and rotate to level position.

2

Stand cabinet up.

4

3

5

6

Rest shelf on supports.

Insert remaining shelves.

Interior

Side View

Interior

Side View

15

Mounting Cabinets (Drywall/Studded Wall)

1

Level cabinet

Gather parts.

2

Align cabinet

to stud marks.

• Follow steps 3 to 5.

• Drill 4 pilot holes through the

perforated strip with hammer drill &

masonry bit.

• Use 4 x (

2 ¼” x ¼” )Tapcon Concrete

Anchor into wall. (Not Included)

• OR 4 x (#10 x 2” )Screw with 3/16”

masonry plug into wall. (Not Included)

• Follow Step 6.

Use stud nder to locate the studs

and mark the wall with a pencil.

4

3

Wall Screw

(1/4” x 2.5”)

Wall Washer

(1/4”)

5

Place cabinet tight

against the wall.

X4

6

Masonry.

Drill 4 wall screws and washers

through perforated holes into studs.

Wall & Locker: 4 wall screws and 4 washers

Corner Wall: 6 wall screws and 6 washers

Base & Tool Cabinet: 2 wall Screws and 2 washers

16

Hanging Cabinets on Wall (optional)

Planning the general position of cabinets.

Step A. Determine the height o the ground you would like the base and locker

cabinets to be and make a horizontal mark at this position.

Step B. Next mark the width of each cabinet in the intended position and ensure

the wall studs fall at least 1.25” in from the edge of the cabinets. This will

ensure there is no interference with the edges of the cabinet and the

wall bracket when hanging the cabinet on the wall.

Note: Ensure there are two studs for the locker to be mounted on as it is easiest to

start the installation with the locker rst. Due to the spacing of the wall studs it is

possible that some base or wall cabinets will only have one stud they will attach

to; This is acceptable as long as the cabinet is bolted to another securely mounted

cabinet.

Parts Needed.

Lag Screw

(1/4” x 2.5”)

Height from Floor

Floor

Wall

studs

must fall

1.25” or

more

from

sides of

cabinet

Wall

studs

must fall

1.25” or

more

from

sides of

cabinet

A

B

Width of Cabinets

Wall Stud

Cabinet Width

Cabinet Layout

2

1

Use stud nder to locate the studs

and mark the wall with a pencil.

17

Planning the general position of cabinets. (cont.)

Step C. Measuring up from the line marked in Step A, make a horizontal mark

at the following heights where they intersect the wall stud marks to

determine where the top of the cabinet will be (and where the

hanging bracket will be installed).

1. Locker: Measure 80” vertically from base line and mark at stud locations.

2. Base: Measure 32.25” vertically from base line and mark at stud locations.

3. Wall cabinets: Measure 80” vertically from base line and mark at stud

locations (if installing ush with top of locker).

Step D. Ensure the cabinets will be at a suitable working height and that your

wall cabinets are not out of reach.

Note: The working surface of the base cabinets will be 1.25” higher than

the cabinet with the top installed.

3

Height from Floor

Floor

Locker & Wall 80”

Base Cabinets 32.25”

A

C

Hanging Cabinets on Wall (cont.)

18

Hanging Cabinets on Wall (cont.)

4

Hanging cabinets on wall.

Align the top of the wall hanging brackets with the lines marked for

the position of the top of the cabinets(Step C) and attach

the brackets securely into the studs using the supplied

lag bolts and washers.

Note: It is possible to oset the bracket to one side or the other if the bracket

is positioned close to the edge of the intended cabinet position by using the

secondary hole positions on the bracket.

Height from Floor

Floor

Locker & Wall 80”

Base Cabinets 32.25”

A

C

WALL

CABINET FRONT

WALL

5

Lift cabinet into place over the brackets and

ush with the wall, and lower into place.

19

Hanging Cabinets on Wall (cont.)

Bolt each subsequent cabinet to the

previous one using the supplied ¼” x 5/8”

hex bolts and lock nuts provided in each

base and wall cabinet.

6

Parts Needed.

Lock Nut

(1/4”)

Washer

(1/4”)

Hex Bolt

(1/4” x 5/8”)

6

X4

WARNING: Wall backets are not designed to support the weight of a loaded cabinet.

Cabinets must be secured to the wall using supplied 1/4” x 2.5” lag screws.

20

WALL STUD

LOCKER

X4

Securing to Wall

Using (4) 1/4” x 2.5” lag screws and washers secure

each cabinet to wall stud from inside cabinet.

Parts Needed.

Bolt

(1/4” x 2.5”)

Wall Washer

(1/4”)

7

Note: Brackets are not designed to support the weight of a loaded cabinet. Cabinets

must be secured to the wall using supplied 1/4” x 2.5” lag screws.

Note: Slatwall Brackets for use with standard 3” slatwall Sold Separately. Check with your

slatwall supplier to determine the rated capacity of your slatwall. DO NOT OVERLOAD.

Hanging Cabinets on Slatwall

1

Insert bolts through slatwall bracket.

Parts Needed.

Wall Bolt

(1/4” x 5/8”)

Wall Washer

(1/4”)

Slatwall Bracket

Lock Nut

(1/4”)

Note:

Do not load cabinet without rst

securing to the wall.

La page est en cours de chargement...

NewAge Products 52582 Guide d'installation

Ce manuel convient également à

NewAge Products 52582 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents