NewAge Products 63274 Mode d'emploi

Cabinets

Project Centre

BOLD 3.0 Series

72in Wall Mounted Rack

Index

Cabinets

72in Wall Mounted Rack

Project Centre

Warning: Excessive weight hazard!

Use two or more people to move, assemble or install cabinets and locker to avoid back injury.

Do not leave children unattended near cabinets. High risk of tipping if cabinets are installed

incorrectly: securely attach cabinets to the wall to avoid serious injury.

For assistance, call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.com

Bold 3.0

IM-PB3.01A-06

STOP

ATTENTION:

Is your cabinet damaged?

Need help or spare parts? For fastest service, contact

NewAge Products at 1-877-306-8930; for U.K 0800-031-4069

or support@newageproducts.com.

Do not return to the retailer.

Use two or more people to move, assemble, or install cabinets and

locker to avoid back injury. Do not leave children unattended near

cabinets. High risk of tipping if cabinets are installed incorrectly:

securely attach cabinets to the wall to avoid serious injury.

For assistance, call 1.877.306.8930; for U.K 0800.031.4069; e-mail at

info@newageproducts.com.

WARNING: Excessive weight hazard!

2

Index

Index 2

Guidelines and Weight Capacity 3

Parts List 3

Tools Needed 5

Warranty 5

Attaching Feet 6

Attaching Casters 7

Removing and Inserting Drawers 8

Installing Corner Cabinet 9

Stacking Cabinets 10

Installing Worktop Support Bracket 11

Attaching Worktop to Cabinets 12

Installing Shelves 13

Securing Cabinets to Drywall/Stud Wall 14

Hanging Cabinets on Slatwall 15

Fastening Cabinets Together 16

Attaching Light Valance 18

Utility Hole Grommet 19

3

200 lbs.

150 lbs.

Lockers

Max 800lbs.

72” Worktop. Fits over 3 Cabinets

48” Worktop. Fits over 2 Cabinets

21” Corner Worktop

Worktop

Weight

Capacity

200lbs.

Base Cabinets

Max 600 lbs.

200 lbs.

Tool Cabinets

Max 600 lbs.

100 lbs.

Wall Cabinets

Max 100 lbs.

100

lbs.

250 lbs per foot.

1000 lbs. per Set of 4

4in Casters

250 lbs. / caster

600 lbs. / set of 4

NOTE:

Claimed weight capacities are only

with NewAge worktops installed

4

Parts Supplied

Unpacking

• Begin by placing the package on a covered at surface.

• Remove all cardboard, foam packaging material and clear plastic bags.

• Dispose / recycle all packaging materials.

• Verify all the contents in the box and gather the required tools. See “Parts” and “Tools Needed” in the list below.

Height-Adjustable

Steel Leveling Legs

Light Valance

Rubber

Grommet

Spring

Washer

Key

Lock Nut

(1/4”)

Washer

(1/4”)

Wood Screw

(#8 x 5/8”)

Wall Screw

(1/4” x 2.5”)

Wall Washer

(1/4”)

Support Bracket

Foot

Attachment

Screws

Full Width

Adjustable

Shelves

Closet Rod

Hex Bolt

(1/4” x 5/8”)

Nut

(M5)

Bolt

(M5 x 12mm)

NewAge Logo

4in Casters

EVA Foam

Drawer Liners

Type Hardware 30-in. Locker 42-in. Locker Wall Corner Wall Base Cabinet

Rolling Tool

Cabinet

Tool Cabinet

#8 x 5/8" Wood Screw 2 2 0 8 4 0 4

1/4" ID x 1/2" OD Washer 22 22 8 8 8 17 8

Spring Washer 0 0 0 0 0 17 0

1/4" Lock Nut 8 8 4 0 4 0 4

1/4" x 0.9" Fender Washer 4 6 4 4 4 0 4

1/4" x 2.5" Wall Screw 4 6 4 8 4 0 4

1/4"-20 x 5/8" Hex Bolts 10 10 4 8 4 17 4

Foot Aachment Screws 17 17 0 0 17 0 17

Keys 2 2 2 2 2 2 2

Light Valence Bolts 0 0 2 2 0 0 0

Light Valence Nuts 0 0 2 2 0 0 0

Plasc Hole C

aps 16 16 8 0 0 0 0

Adustable Leveling Feet 4 4 0 0 4 0 4

Power Cord Grommet - 2in 1 1 0 0 1 0 0

4in Swivel

Casters 0 0 0 0 0 2 0

4in FIXED Casters with Brakes

0 0 0 0 0 2 0

Adjustable Shelves 3 3 0 0 1 0 0

Cabinet Leg 4 4 0 0 4 0 4

Closet Rod 1 1 0 0 0 0 0

EVA Foam Drawer Liners 0 0 0 0 0 4 4

Light Valence 0 0 1 1 0 0 0

NewAge Logo 1 1 0 0 0 0 0

Included Brackets Side Support Bracket 1 1 0 2 0 0 0

Hardware Pack

Addional Hardware

I

ncluded Component

s

5

Tools Needed

1 x 12” Magnetic Leveler

1 x #2 Phillips Bit

1 x Tape Measure

1 x 7/16” socket

1 x Cordless Power Drill

1 x Stud Finder

1 x Pencil1 x Set

Square

1 x Hammer Drill 1 x Masonry Bit

1 x Adjustable wrench

1 x 7/16” Socket driver

wrench

1 x 8mm” Socket driver

wrench

1 x #2 Phillips

head screw driver

1 x #3 Phillips

head screw driver

[optional for masonry]

1

1 2 3

2

3

Manufacturer Warranty Limited Lifetime

1. Service calls to correct the installation of any NewAge products or to instruct you how to use or install them.

2. Damage resulting from improper handling or shipping of products, or products damaged by accident, misuse, abuse, re,

ood, improper installation, acts of God, neglect, corrosion, modication or mishandling.

3. Products damaged by improperly loading beyond the specied maximum weight capacity outlined in the instructions provided

with the product.

4. Repairs or replacement when your product is used in other than normal, single-family household use, such as a commercial

environment, or handled in anyway inconsistent with the installation instructions included with the product.

5. Cosmetic damage, including scratches, dings, dents or cracks in paint that do not aect the structural or functional capability

of the product.

6. Surfaces damaged due to chemical interaction resulting in corrosion of paint or metal.

7. Replacement parts for NewAge products outside Canada and the United States.

8. Replacement keys or locking mechanisms.

9. Loss of product contents due to theft, re, ood, accident or acts of God.

10. Shipping or freight fees to deliver replacement products or to return defective products.

11. Any labor costs during the limited warranty period.

When this product is installed, operated and maintained according to the instructions attached to or furnished with the product,

NewAge Products Inc. will replace the defective product or parts if the part fails as a result of defective materials or workmanship

for the Lifetime of the product.

NEWAGE PRODUCTS INC. WILL NOT PAY FOR:

IMPLIED WARRANTIES, INCLUDING TO THE EXTENT APPLICABLE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE, ARE EXCLUDED TO THE EXTENT LEGALLY PERMISSIBLE. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED

TO ONE YEAR, OR THE SHORTEST PERIOD ALLOWED BY LAW. SOME STATES AND PROVINCES DO NOT ALLOW LIMITATIONS OR EXCLUSIONS

ON HOW LONG AN IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT

APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE

TO STATE OR PROVINCE TO PROVINCE

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

6

Installing the Feet

1

Flip cabinet upside down,

locate holes at corners.

2

Stand & level feet.

Open cabinet, remove any shelves

or loose items.

Repeat step 3 for each corner.

5

4

Parts Needed.

16 X Foot

Attachment Screws

4 X Foot

Align foot with edge of cabinet. Screw in

4 x foot attachment screws using

#3 philips screwdriver.

3

7

Installing Casters

1

Flip cabinet upside down,

locate holes forming a square.

2

Open cabinet, remove any shelves

or loose items.

Repeat steps 3 for each corner.

4

Parts Needed.

16 X Lock Nut

(1/4”)

32 X

Washer

(1/4”)

16 X Hex Bolt

(1/4” x 5/8”)

4 x Casters

Align caster holes and bolt to cabinet using

4 Hex bolts and Lock nuts with 8 washers

3

5

Note:

Casters sold seperately.

8

Right Side

Left Side

Slide In

Slide Out

Align Rails

Inserting Drawers.

Removing Drawers.

Installing the Drawers

9

Slide in corner and attach

remaining cabinets.

A

B

Installing Corner Cabinet

1

Attach top to one cabinet using 1/4” x

5/8 hex bolts, nuts, and washers.

Attach second cabinet to top.

2

On adjacent edges attach 2 support

brackets to underside of corner top

using the supplied (4) #8 x 5/8” screws.

Parts Needed.

3

Wall Washer

(1/4”)

# 8 x 5/8”

Screw

1/4” x 5/8

Hex Bolt

Lock Nut

(1/4”)

4

1

1 2 3

2

3

Note: Ensure there is enough assembly

room. Cabinets must be assembled away

from corner to access backs of cabinets.

Important:For mounting top ush with back of

cabinet follow step A, for mounting top ush wtih

front follow step B and ush with edge step C.

10

Stacking Cabinets

1

Locate punch holes on adjoining

surface and insert bolts.

Tighten all bolts

2

Attach cabinets using the supplied

1/4” x 5/8” hex bolts, washers, and

nuts.

Position a second base cabinet on

top of an existing base cabinet.

3

I

Parts Needed.

4 X Lock Nut

(1/4”)

8 X

Washer

(1/4”)

4 X Hex Bolt

(1/4” x 5/8”)

4

11

Installing Worktop

Side Support Bracket

Note: Support Bracket Sold Separately

A support bracket is to be used if the worktop is

added to the set without a secondary supporting

base/tool cabinet.

X2

Fasten nuts, bolts, and lock washers.

2

Tighten nuts & bolts.

Parts Needed.

4

3

5

Align bracket.

Level bracket and ensure it is at the

same height as the base cabinet.

1

Open locker and locate holes on either side.

2 X Lock Nut

(1/4”)

4 X

Washer

(1/4”)

2 X Hex Bolt

(1/4” x 5/8”)

Support

Bracket

12

Mounting the Worktop (On 2 Cabinets)

1

Optional: For locker support bracket.

X4 X2

X2

Locate 2 punch holes both sides.

2

Drill into the worktop using the #8 x 5/8” wood screws.

X2

Use 2 washers & #8 x 5/8” wood screws.

Provided in the locker packaging.

Place worktop on cabinets.

3

I

13

Inserting Cabinet Shelves

1

Level shelf.

2

Stand cabinet up. Insert shelf at a slight angle.

4

3

5

6

Lower shelf onto brackets by sliding

tabs into slots.

Ensure shelf is clipped in position.

Insert remaining shelves.

14

Mounting Cabinets (Drywall/Studded Wall)

1

Level cabinet by

adjusting feet

Parts Required

Align cabinet

to stud marks.

• Follow steps 2 to 4.

• Drill 4 pilot holes through the

perforated strip with hammer drill &

masonry bit.

• Follow Step 5 using:

• Use 4 x (

2 ¼” x ¼” )Tapcon Concrete

Anchor into wall. (Not Included)

• OR 4 x (#10 x 2” )Screw with 3/16”

masonry plug into wall. (Not Included)

Use stud nder to locate the studs

and mark the wall with a pencil.

4

3

Wall Screw

(1/4” x 2.5”)

Wall Washer

(1/4”)

Place cabinet tight

against the wall.

X4

Masonry.

Drill 4 wall screws and washers

through perforated holes into studs.

Wall & Locker: 4 wall screws and 4 washers

Corner Wall: 6 wall screws and 6 washers

Base & Tool Cabinet: 2 wall Screws and 2 washers

2

5

15

Using 1/4” drill socket or 1/4” wrench securely tighten lock

nuts to each wall bracket from inside cabinet .

WALL STUD

LOCKER

Hanging Cabinets on Slatwall

1

Attach braket to slatwall at desired

height. For Locker cabinet attach

second bracket 65” below rst bracket.

Align bolt with slots on back of cabinet

and hang cabinet.

2

Insert bolts through slatwall bracket.

Parts Needed.

3

3x Wall Washer

(1/4”)

3x Lock Nut

(1/4”)

Slatwall Bracket

4

WALL CABINET

BASE CABINETS

3 X Hex Bolt

(1/4” x 5/8”)

Note: Slatwall Brackets for use with standard 3” slatwall Sold Separately. Check with your

slatwall supplier to determine the rated capacity of your slatwall. DO NOT OVERLOAD.

NewAge Slatwall Brackets are only compatible with standard 3” on center Slatwall.

16

Fastening Cabinets

Note:

Fasten additional cabinets to

initial securely mounted cabinet.

1

Align bolts, tighten lightly.

Level cabinets and tighten all bolts.

2

Parts Needed.

Lock Nut

(1/4”)

Washer

(1/4”)

Hex Bolt

(1/4” x 5/8”)

X4

Note:

Remove all drawers before

fastening cabinets

17

X4

Attaching Light Valance to Wall Cabinet

1

Insert and tighten bolt and nuts.

2

Align holes of valance with cabinet.

3

Cross Section View

Parts Needed.

Light Valance

Nut

(M5)

Bolt

(M5 x 12mm)

18

2

Utility Access

1

Insert rubber grommet into cut-out

hole in bottom panel.

The utility access hole allows easy

connection to power outlet.

Thank you for purchasing a NewAge Product!

Please give us a call or visit online if you have any questions.

Call 1.877.306.8930; for UK 0800.031.4069; e-mail at info@newageproducts.com

La page charge ...

NewAge Products 63274 Mode d'emploi

NewAge Products 63274 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents