Nextar X3-01 - Satellite Navigation 3.5" Color Touch Screen Model3 Manuel utilisateur

1

POWER SUPPLY:

Connect the supplied adaptor to the side of the unit in the slot marked “DC 5V IN”. Plug

the two-prong end of the power cord to an AC100-240V outlet. If you have difficulty

inserting the plug, turn it over and reinsert it. If the unit is not used for a long time,

disconnect the plug from the outlet.

NOTE:

Before plugging the power cord into an AC outlet, make sure that all the connections

have been made.

CAUTION: These servicing instructions are for use by qualified service personnel only.

To reduce the risk of electric shock, do not perform any servicing other than that

contained in the operating instructions unless you are qualified to do so.

Refer to service manual for servicing instructions. To reduce the risk of fire or electric

shock, do not expose this apparatus to rain or moisture.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USE-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is

intended to alert the user to the presence of uninsulated “dangerous voltage”

within the product’s enclosure that may be of sufficient magnitude to constitute

a risk of electric to

p

ersons.

The exclamation point within an equilateral triangle is intended to alert the use

r

to the presence of important operating and maintenance (servicing)

instructions in the literature accompan

y

in

g

the appliance.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OF MOISTURE.

Important

S

a

f

ety

Instructions

2

NOTES

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with a damp cloth.

7) Do not block any of the ventilation openings. Install in accordance with the

manufacturer's instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug

has two blades with one wider than the other. A grounding type plug has two blades and

a third grounding prong. The wide blade or the third prong is provided for your safety.

When the provided plug does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with a cart, stand, tripod, bracket, or table specified by the

manufacturer, or sold with the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is damaged,

liquid has been spilled or objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has been dropped.

15) Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids,

such as vases, shall be placed on the apparatus.

To prevent the GPS from being damaged, be sure to keep the GPS out of direct

sunlight or heat.

Important

S

a

f

ety

Instructions

3

Warning

Failure to avoid the following potentially hazardous situations may result in injury or

property damage.

The unit is designed to provide you with route suggestions. It does not reflect road

closures or road conditions, traffic congestion, weather conditions, or other factors that

may affect safety or timing while driving.

Use the unit only as a navigational aid. Do not attempt to use the unit for any purpose

requiring precise measurement of direction, distance, location, or topography. This

product should not be used to determine ground proximity for aircraft navigation.

CAUTION:

Danger of explosion if battery is incorrectly replaced. Replace only with the same or

equivalent type.

The batteries (or batteries installed) shall not be exposed to excessive heat such as

sunshine, fire or the like.

Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability of the

Global Positioning System (“GPS”) hardware, operating software or other aspects of this

product. UL has only tested for fire, shock or casualty hazards as outlined in UL’s

Standard(s) for Safety [Note-Consider referencing specific UL standard].

UL Certification does not cover the performance or reliability of the GPS hardware and

GPS operating software.

UL MAKES NO REPRESENTATIONS, WARRANTIES OR CERTIFICATIONS

WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY GPS

RELATED FUNCTIONS OF THIS PRODUCT.

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may

cause undesired operation.

Important

S

a

f

ety

Instructions

4

Note: This equipment has been tested and found to comply with limits for Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and the receiver. Connect the

equipment into an outlet on a circuit different from that to which the receiver is

connected.

3. Consult the dealer or an experience radio/TV technician for help.

Cleaning of touch screen

If touch screen has fingerprints or dust on it, lightly wipe the touch screen with dry soft

cloth (or similar).

Never use record cleaning sprays, benzene, thinner, static electricity prevention liquids

or any other solvents to clean your touch screen.

The images in this manual are for reference only and they may appear

different from the actual items.

Important

S

a

f

ety

Instructions

5

Navigation Function

Other Special Functions

Navigation Function: The unit is designed to provide you with route suggestions. It supports voice

navigation.

Power Adaptor Switch: Automatically

adapts to voltage requirements in U.S and

other countries.

SD Card and USB Input: The unit is

designed with SD card and USB ports and

can be connected to SD card or other USB

device for file loading.

Flash Storage: Built in Flash Storage can

store map data.

Support file formats: Supports MP3

Format files playback.

Features

6

Accessories List

ITEM NAME QTY

Instruction Manual 2

AC Adaptor 1

Car Adaptor 1

USB Cable 1

Windshield Mount Bracket 1

Mount Cradle 1

Dashboard Mount Disk 1

Stylus 1

1GB SD card with maps 1

Pouch 1

NOTE

Accessories and their part number are subject to modification without prior notice due to

improvements.

Accessories

7

……………………………………….……..1

……………………………………………...5

……………………………………………...6

……………………………………………...8

……………………………………….……..9

…………………………..……….…....….10

………………………………………..…..12

………………………………………..…..16

………………………………………....…18

………………………………………..…..19

………………………………………..…..20

Important Safety Instructions

Features

System Connections

Power Supply Preparation

Troubleshooting

General Setup

Specifications

A

ccessories

View of Main Unit

Playing Music

Use of the Mount Accessories

Contents

8

1. LCD Screen

2. POWER Button

Press to enter or exit the standby

mode.

3. Card Slot

Insert the SD card into the slot.

4. Headphone Jack

5. DC 5V Input Jack

Used to connect to the supplied car

adaptor.

6. USB Port

7. RESET Button

Press to reset the system.

View of Main Unit

9

 Always ensure that the unit and any other external device connected to the unit are

switched off and unplugged from the power supply before you attempt to connect

the unit to any external device.

Inserting SD Card

The unit is designed with SD Card slot that allows you to insert an SD card into the unit

as shown below:

To remove the card, gently press the card in with your fingernail. The card unlocks and

protrudes slightly. You can now remove the card.

Connecting to Headphones

Connect the headphones to the right side of the unit for private listening.

When headphone is connected, the speakers will automatically turn off.

Note: Overly loud volume could damage your hearing. So turn down the volume before

you connect the headphones, and then raise the volume to comfortable level.

System Connections

10

Using the AC Adaptor

The unit is supplied with an AC adaptor for powering and charging the battery.

Note

 Turn unit's power off before unplugging.

 When using the adaptor, the LCD screen will be brighter than with the

rechargeable battery.

Using the Car Adaptor

The unit is supplied with a Car Adaptor for powering while in a vehicle.

Attention

 Place the unit in a proper position for viewing.

 Disconnect the unit from the car adaptor when starting the vehicle.

Your portable GPS comes with a built-in rechargeable battery. Please see details in the

following segment.

Connect the car adaptor power plug

to the unit’s power jack and plug the

other end to the vehicle’s 5V

accessory/ cigarette socket, as

shown on the right figure.

1. Connect AC adaptor to the

right side of the unit in the jack

marked DC 5V IN, as shown on

the right.

2. Plug the two-prong end of the

power cord into a grounded

electrical outlet.

Power Supply

Preparation

11

About Rechargeable Battery

Your portable GPS comes with a built-in rechargeable battery. Charge the battery fully

before initial use. Charging time is normally about 3.5 hours. A fully charged battery

delivers about 3 hours of use.

Working conditions and precautions for the rechargeable battery

 New batteries should be fully charged before initial use.

 Battery should only be used when temperatures are between 14-140F(-10

℃-60

℃). And it should be charged when temperatures are between 32-113F(0℃-45

℃)

 Maintain well-ventilated conditions around the product to avoid overheating. Don’t

put the product on a bed, sofa or anything that may block ventilation to the product.

 When the battery is weak, an indication menu will appear on the LCD screen and

the unit will power off automatically after a while.

Charging the Battery Pack

The battery must be charged using the supplied adaptor.

Power Supply

Preparation

12

System Main Menu

When in navigation mode, tap button in the Menu screen. A confirmation message

appears asking if you want to exit the program now, as shown below.

In the confirmation screen, tap Yes and the system main menu appears.

In the system main menu, there are three items for selecting. Touch the corresponding

item to enter. Tap

to enter navigation mode. Tap to enter the settings

menu. Tap

to enter the Music player.

Settings Menu

Tap to enter the settings menu, the screen will display as below:

In the menu, tap

to return to the main menu.

General Setup

13

LANGUAGE

Tap

in the settings menu to enter LANGUAGE settings menu for language

selecting, as shown below:

Tap the

buttons to select language. Then tap to confirm or tap to

cancel.

BRIGHTNESS

Tap

in the settings menu to enter BRIGHTNESS settings menu for brightness

adjusting, as shown below:

Tap the first group

buttons to adjust the brightness level.

After setting, tap

to confirm or tap to cancel.

General Setup

14

DATE & TIME

Tap

in the settings menu to enter DATE & TIME settings menu for changing to

the current time zone, as shown below:

Tap the

buttons to select the proper Time Zone. Tap the buttons of

Date group to change the corresponding date and tap the

buttons of Time group

to change the corresponding time. Tap

to return.

POWER

Tap

in the settings menu to enter POWER menu for the current battery status, as

shown below:

The power menu will display the current battery status. Tap

to return.

General Setup

15

CALIBRATE

Tap

in the settings menu to enter CALIBRATE menu for calibrating the sensitivity

of the unit, the screen will display as below:

Tap the center of “+” as it moves around the screen. If you touch the center of “+” every

time, it will disappear and tap the screen to return to the settings menu.

Note: If “+” doesn’t disappear, you should calibrate again.

MASTER VOLUME

Tap

in the settings menu to enter VOLUME settings menu for master volume

adjusting, as shown below:

Tap the

buttons to adjust the master volume. Then tap to confirm or tap

to cancel.

Note: there are two levels of volume control: one is the master control in the general

set-up; the secondary volume control is in the navigation or mp3.

General Setup

16

The unit is designed with a SD card slot and supports MP3 and WMA format files

playback. To use the music player, you will need to have an SD card with your MP3

music files preloaded. Please note that you cannot use the navigation function of the

device at the same time you are using the music player. Remove the mapping software

SD card that comes with the device from the SD card slot on the side of the unit. Then

insert your SD card with your MP3 or WMA music files.

Note: Please take care of the mapping SD card if you remove it to use the MP3

Player as the navigation function will not work without it.

Warning: For your own safety, do not use the earphones when driving.

A note regarding the MP3 function

The unit has the ability to play your favorite MP3 music files. This is accomplished by

using the unit’s SD card slot, located on the right side.

 MP3 files should previously reside on the user’s SD card.

 MP3 files can be imported to the user’s SD card on a PC, using a variety of

programs such as Windows Media Player.

 This process should be performed independent of the navigation unit.

Do not attempt to use the unit to read and burn MP3 files from an external source.

Playing Music.

In the main menu, tap to enter the MP3 main screen, as shown below:

In the MP3 player, tap

in the top left corner to exit.

Playing Music

17

In the menu, tap the MENU button to enter the MP3 play list menu, as shown below:

When you open the play list, the system will look for audio files on its SD memory card

and create a play list automatically. If the play list consists of more than one screen, tap

the up arrow

for the previous page and the down arrow for the next page.

In the play list, double tap the songs to start playback.

Tap ; when the button changes to orange, the player will repeat all the songs in the

play list.

Tap

; when the button changes to orange, the player will play the songs in the list

randomly.

Tap

to return to the MP3 main screen.

On the playback screen as shown right, the MP3 player

has standard playback features:

Tap

button to start playing the songs in the play list.

Tap

to stop the playback.

Tap

to pause the playback, and then tap to resume the playback.

Tap

to go back to the previous song; tap to skip to the next song.

Use

to adjust the volume of the speaker.

Tap

to select the desired playback starting time.

Playing Music

18

When using the unit in vehicle, you can use the supplied mount accessories (mount

bracket, mount cradle and dashboard mount disk) to mount the unit in the vehicle. Take

the following steps to operate:

1. See Fig. 1. Push the mount cradle to mount bracket.

2. See Fig. 2. Fix the unit on mount cradle and bracket.

3. See Fig. 3. Lift the suction fastener, and place the unit on the desired location, then

press down fastener for immobility. Rotate the knob to adjust the unit to proper

position.

If you want to mount the unit to the dashboard, you can use the adhesive disk:

1) Choose a clean, dry spot on your dashboard

2) Peel off protection liner from the back of the disk.

3) Attach the disk to your dashboard.

4) Mount the bracket to the adhesive disk.

Use of the Mount

Accessories

19

Take steps described in the tables below to solve simple problems before contacting

customer service.

If you suspect something wrong with this unit, immediately turn the power off and

disconnect the power connector from the unit. Never try to repair the unit yourself

because it is dangerous to do so.

Other possibilities:

Static or other external interference may cause the unit to function abnormally. In order to

recover normal status, please unplug the power supply cord and then plug it into the outlet

again to reset the unit. If the problems still exist, please cut off the power supply and consult

your service center or a qualified technician.

There is no sound

The volume may be turned

down.

Turn up the volume.

There is no picture.

The brightness may be

turned down.

A

djust the brightness of the

LCD.

PROBLEM

POSSIBLE CAUSE

POSSIBLE SOLUTION

Troubleshooting

La page charge ...

Nextar X3-01 - Satellite Navigation 3.5" Color Touch Screen Model3 Manuel utilisateur

Ce manuel convient également à

Nextar X3-01 - Satellite Navigation 3.5" Color Touch Screen Model3 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents