Jenn-Air JFI2589AES10 Le manuel du propriétaire

Marque: Jenn-Air

Modèle: JFI2589AES10

Catégorie: Frigos

Taper: Le manuel du propriétaire

THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING,

please visit our website at www.jennair.cem for additional information. If you still need assistance, call us at 1-800-688-1100. In

Canada, visit our website at www.jennair.ca or call us at 1-800-807-6777.

You will need your model and serial number located on the right-hand side of the refrigerator interior.

Para obtener acceso a "lnstrucciones para el usuario del refrigerador" en espaSol, o para obtener informaci6n adicional acerca de

su producto, visite: www.jennair.com.

Tenga listo su nQmero de modelo complete. Puede encontrar su nQmero de modelo y de serie en la etiqueta ubicada al lade

derecho del interior del refrigerador.

TableofContents/Tabledes mati res

REFRIGERATOR SAFETY ....................................................... 1

INSTALLATION INSTRUCTIONS ............................................ 2

REFRIGERATOR USE.............................................................. 8

REFRIGERATOR CARE ......................................................... 12

TROUBLESHOOTING ............................................................ 13

WATER FILTER CERTIFICATIONS ...................................... 15

PRODUCT DATA SHEETS .................................................... 16

WARRANTY ............................................................................ 17

SI:!:CURIT¢ DU RI:!:FRIGCRATEUR ....................................... 18

INSTRUCTIONS D'INSTALLATION ..................................... 19

UTILISATION DU REFRIGI:!:RATEUR .................................. 25

ENTRETIEN DU REFRIGI:!:RATEUR ..................................... 30

DI:!:PANNAGE ......................................................................... 31

FEUILLES DE DONNEES SUR LE PRODUIT ..................... 34

GARANTIE ............................................................................. 35

REFRIGERATORSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

12828144A

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all parts and panels before operating.

• Remove doors from your old refrigerator.

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

• Use two or more people to move and install refrigerator.

• Disconnect power before installing ice maker (on ice maker

kit ready models only).

• Use a sturdy glass when dispensing ice (on some models).

SAVE THESE INSTRUCTIONS

ProperDisposalofYourOld Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." If you are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:.

• Take off the doors.

• Leave the shelves in place so that children may not easily

climb inside.

INSTALLATIONINSTRUCTIONS

When Moving Your Refrigerator:

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

Your refrigerator is heavy. When moving the refrigerator

for cleaning or service, be sure to protect the floor.

Always pull the refrigerator straight out when moving it.

Do not wiggle or "walk" the refrigerator when trying to move

it, as floor damage could occur.

Remove the Packaging

Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with warm water

and dry.

Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see "Refrigerator Safety."

• Dispose of/recycle all packaging materials.

Clean Before Using

After you remove all of the packaging materials, clean the inside

of your refrigerator before using it. See the cleaning instructions

in "Refrigerator Care."

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass

shelves and covers are heavy. Use special care when

removing them to avoid impact from dropping.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to de so can result in death, explosion, or fire.

To ensure proper ventilation for your refrigerator, allow for a 1/211

(1.25 cm) space at the top and behind the refrigerator. If your

refrigerator has an ice maker, allow extra space at the back for

the water line connections. When installing your refrigerator next

to a fixed wall, leave a 2%" (7.0 cm) minimum space between the

refrigerator and wall to allow the door to swing open.

NOTE: It is recommended that you do not install the refrigerator

near an oven, radiator, or other heat source. Do not install the

refrigerator in a location where the temperature will fall below

55°F (13°C).

1/2" (1.25 cm)

2¾" (7.0 cm)

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical

connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only, 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the control (Thermostat, Refrigerator

or Freezer Control depending on the model) to OFF and then

disconnect the refrigerator from the electrical source. When you

are finished, reconnect the refrigerator to the electrical source

and reset the control (Thermostat, Refrigerator or Freezer Control

depending on the model) to the desired setting. See "Using the

Controls."

Gathertherequiredtoolsandpartsbeforestartinginstallation.

Readandfollowtheinstructionsprovidedwithanytoolslisted

here.

TOOLS NEEDED:

• Flat-blade screwdriver • %" Nut driver

• 7Ad'and W' Open-end or two • W' Drill bit

adjustable wrenches • Cordless drill

IMPORTANT:

• All installations must meet local plumbing code requirements.

• Do not use a piercing-type or 3/_6"(4.76 mm) saddle valve

which reduces water flow and clogs more easily.

• Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

Water Pressure

A cold water supply with water pressure of between 35 and

120 psi (241 and 827 kPa) is required to operate the water

dispenser and ice maker. If you have questions about your water

pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 35 and 120 psi (241 and

827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

If your refrigerator has a water filter, it may further reduce the

water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See "Water

Filtration System."

If you have questions about your water pressure, call a licensed,

qualified plumber.

Read all directions before you begin.

IMPORTANT: If you turn the refrigerator on before the water line

is connected, turn the ice maker OFE

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Locate a _/2"to 1W' (12.7 mm to 31.8 mm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from

the drill and normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure

from the connection on the rear of the refrigerator to the

water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use Y4"

(6.35 mm) O.D. (outside diameter) copper tubing. Be sure

both ends of copper tubing are cut square.

5. Using a cordless drill, drill a W' hole in the cold water pipe you

have selected.

A. Cold water pipe

B. Pipe clamp

C. Copper tubing

D. Compression nut

E. Compression sleeve

F. Shutoff valve

G. Packing nut

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the W' drilled hole

in the water pipe and that the washer is under the pipe clamp.

Tighten the packing nut. Tighten the pipe clamp screws

slowly and evenly so washer makes a watertight seal. Do not

overtighten or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and

turn ON the main water supply. Flush the tubing until water is

clear. Turn OFF the shutoff valve on the water pipe. Coil the

copper tubing.

Connect to Refrigerator

1. Remove plastic cap from water supply connection. Place

brass nut and compression sleeve on copper tube end as

shown.

A. Brass nut

B.Compression sleeve

2. Place end of copper tubing into plastic water valve supply

line. Slide the brass nut over the sleeve and screw the nut into

supply line.

3. Using an adjustable wrench, hold the nut on the plastic water

line to keep it from moving. Then, with a second wrench turn

the nut on the copper tubing counterclockwise to completely

tighten. Do not overtighten.

4. Check connection by pulling on the copper tubing.

5. Attach the copper tubing to the refrigerator with a "P" clamp.

Slide the plastic waterline into the retainer.

A. "P" Clamp

B. Brass nut

C. Compression sleeve

Turn on water supply to refrigerator and check for leaks.

Correct any leaks.

Complete the Installation

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord,

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See "Water and Ice Dispenser."

NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to

completely fill the ice container.

All graphics referenced in the following instructions are included

later in this section after "Final Steps."

Remove and Replace Handles

1. Using a %2" Allen wrench, loosen the two set screws located

on the side of each handle. See Metal Handle graphics 1

and 2.

2. Pull the handle straight out from the door. Make sure you

keep the screws for reattaching the handles.

3. To replace the handles, reverse the directions.

Remove Doors and Hinges

IMPORTANT:

• Remove food and any adjustable door or utility bins from

doors.

• Keep the refrigerator doors closed until you are ready to lift

them free from the cabinet.

NOTE: Provide additional support for the refrigerator door

while the hinges are being removed. Do not depend on the

door gasket magnets to hold the door in place while you are

working.

TOOLS NEEDED: %6", %", 1/4"hex-head socket wrench,

#2 Phillips screwdriver, and a flat-blade screwdriver.

1. Unplug refrigerator or disconnect power.

2. Remove the base grille. Grasp the grille firmly and pull it

toward you.

3. Starting with the right-hand side door, remove the parts for

the top hinge as shown in Top Hinge graphic. Lift the

refrigerator door from the bottom hinge pin.

4. Remove the shim from the bottom hinge pin and keep it for

later use. See Bottom Hinge graphic.

5. Remove top hinge cover from left side refrigerator door.

Disconnect the wiring plug located on top of the hinge by

wedging a flat-blade screwdriver or your fingernail between

the two sections. See Connections graphic.

6. Disconnect the water line by holding the tabbed section of

the water line while turning the black locking collar clockwise.

See Connections graphic.

7. Remove the parts for the top hinge as shown in Top Hinge

graphic. Lift the left-hand side door from the bottom hinge

pin.

NOTE: On some models, remove the shim from the bottom

hinge pin and keep it for later use. See Bottom Hinge graphic.

8. Using a %" hex wrench, remove the leveling leg brackets from

the bottom of the cabinet. Keep screws for later use.

Replace Doors and Hinges

Assemble the parts for the top hinge as shown in Top Hinge

graphic. Do not tighten the screws completely.

Replace the parts for the bottom hinge as shown in Bottom

Hinge graphic. Tighten screws, Replace the refrigerator door.

NOTE: Provide additional support for the refrigerator door

while the hinges are being moved. Do not depend on the door

gasket magnets to hold the door in place while you are

working.

3. Align the door so that the bottom of the refrigerator door

aligns evenly with the top of the freezer drawer. Tighten all

screws.

4. Reconnect the wiring plug on top of the left-hand side

refrigerator door.

5. Reconnect the water lines by firmly pushing one line inside

the other. Slide the black locking collar fully forward.

6. While holding the tabbed section of the waterline, turn the

locking collar counterclockwise until you hear a "click."

NOTE: The arrow on the tabbed section should align with the

two bars on the locking collar.

7. Check for leaks. Replace the top hinge covers.

Remove and Replace Freezer Drawer

IMPORTANT: Two people may be required to remove and

replace the freezer drawer. Graphics are included later in this

section.

Remove Drawer Front

1. Open the freezer drawer to full extension.

2. Loosen the four screws attaching the drawer glides to the

drawer front. See Drawer Front Removal graphic.

NOTE: Loosen screws three to four turns. Keep the screws in

the drawer front.

3. Lift drawer front upward and off the screws. See Drawer Front

Removal graphic.

Replace Drawer Front

1. Slide the drawer glides out of the freezer compartment. Insert

the screws in the top of the drawer front into the slots in the

drawer brackets. See Drawer Front Replacement graphic.

2. Pull the drawer brackets toward you to position the two

screws in the bottom of the drawer front into the brackets.

See Drawer Front Replacement graphic.

3. Completely tighten the four screws.

Final Steps

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord,

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug in refrigerator to a grounded 3 prong outlet.

2. Return all removable parts to doors and drawer and food to

refrigerator and freezer.

Top Hinges

A. Hinge Cover Screw

B. Top Hinge Cover

C. 5A_"Hex-Head Hinge Screws

D. Top Hinge

Connections

A. Tabs

B. Wiring Plug

Metal Handle

A. %2" Set Screw

A. Loosen Door Bracket Screws

Depending on your model, your refrigerator may have four

adjustable rollers (Style 1) or a leveling screw (Style 2)located at

the base of the refrigerator. Ifyour refrigerator seems unsteady or

you want the door to close more easily, use the instructions

below.

1. Remove the base grille. Grasp the grille firmly and pull it

toward you.

2= Raise or lower the cabinet.

Style 1 - Front and rear leveling

Using a %" hex driver, turn the roller adjustment screw(s) on

each side to raise or lower that side of the refrigerator.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the adjustment screws and

rollers. This makes it easier to turn the screws. It may take

several turns of the roller adjustment screw to adjust the tilt of

the refrigerator.

• To raise, turn the roller adjustment screw to the right.

• To lower, turn the roller adjustment screw to the left.

Turn the brake foot clockwise until it is firmly against the floor

to keep the refigerator from rolling forward when the freezer

drawer is pulled open.

A. Rear roller adjustment screw

B. Front roller adjustment screw

C. Brake foot

Style 2 - Leveling screw

Using a 1/4"hex driver, turn the leveling screw on each side to

raise or lower that side of the refrigerator.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws. This

makes it easier to turn the screws. It may take several turns of

the leveling screw to adjust the tilt of the refrigerator.

• To raise, turn the leveling screw clockwise.

To lower, turn the leveling screw counterclockwise.

A. Levelingscrew

3. Open the door again to make sure that it closes as easily as

you like. If not, tilt the refrigerator slightly more to the rear by

turning both leveling screws clockwise. It may take several

more turns, and you should turn both screws the same

amount.

4. Replace the base grille.

REFRIGERATORUSE

There are two refrigerator compartment doors. The doors can be

opened and closed either separately or together.

There is a vertically-hinged seal on the left refrigerator door.

• When the left side door is opened, the hinged seal

automatically folds inward so that it is out of the way.

• When both doors are closed, the hinged seal automatically

forms a seal between the two doors.

A. Hinged seal

IMPORTANT:

• The control panel is located on the front of the ice and water

dispenser.

To access the main control menu, press any of the four touch

pads located on either side of the display. Then, touch the

pad next to the desired option or user setting to access the

various features.

NOTE: Press only the touch pads next to your selection on

the display screen, not the selection itself.

Wait24hoursforyourrefrigeratortocoolcompletelybefore

addingfood.Ifyouaddfoodbeforetherefrigeratorhas

cooledcompletely,yourfoodmayspoil.

NOTE:Adjustingtherefrigeratorandfreezertemperature

controlstoacolderthanrecommendedsettingwillnotcool

thecompartmentsanyfaster.

Therecommendedsettingsshouldbecorrectfornormal

householdrefrigeratoruse.Thecontrolsaresetcorrectly

whenmilkorjuiceisascoldasyoulikeandwhenicecream

isfirm.

Ifthetemperatureistoowarmortoocoldintherefrigeratoror

freezer,firstchecktheairventstobesuretheyarenot

blockedbeforeadjustingthecontrols.

A j

A. Touch pads

Temperature Controls

For your convenience, your temperature controls are preset at

the factory. When you first install your refrigerator, make sure the

controls are still set to the recommended set points.

• Press the touch pad next to "FRESH FOOD TEMP" on the

main menu to display the current set point of the

compartment. Press the touch pad next to "WARMER" or

"COLDER" to adjust the set point to the recommended 38°R

Press the touch pad next to "Done" to lock in the setting.

Press the touch pad next to "FREEZER TEMP" on the main

menu to display the current set point of the compartment.

Press the touch pad next to "WARMER" or "COLDER" to

adjust the set point to the recommended 0°R Press the touch

pad next to "Done" to lock in the setting.

To Turn Cooling Off/On:

Cooling On/Off controls all cooling functions, the control panel

and the dispenser. It does not disconnect power to the

refrigerator.

• Press and hold the On/Off button for three seconds. The LED

will light up to indicate that cooling is Off. Neither

compartment will cool.

• Press the On/Off button again to turn on the cooling. The LED

will turn off.

[]

Cooling

hold3sec

Adjusting Controls

The FRESH FOOD TEMP control adjusts the refrigerator

compartment temperature. The FREEZER TEMP control adjusts

the freezer compartment temperature.

If you need to adjust the temperature in either the refrigerator or

freezer compartment, use the settings listed in the chart as a

guide.

To Adjust Set Point Temperatures:

The display will show the set point for approximately 3 seconds.

• Press the touch pad next to "WARMER" or "COLDER" to

adjust the set point to the desired temperature. Then, press

the touch pad next to "Done" to lock in the new set point

temperature.

NOTE: Except when first turning on the refrigerator, do not adjust

either temperature control more than one setting at a time. Wait

24 hours for the temperature to stabilize between adjustments.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR too warm FRESH FOOD Control

1olower

FREEZER too warm/too little ice FREEZER Control

1olower

REFRIGERATOR too cold FRESH FOOD Control

1ohigher

FREEZER too cold FREEZER Control

1ohigher

Options

Door Alarm

The Door Alarm feature sounds an audible alarm every few

seconds when the either refrigerator door has been left open for

3 continuous minutes. The alarm will sound until the door is

closed or Door Alarm is turned off.

1. On the main menu, press the touch pad next to "Options."

2. Press the touch pad next to "Door Alarm Is On" to switch

between ON and OFR Press the touch pad next to "Done" to

lock in the desired setting and return to the main menu.

Humidity Control (on some models)

The humidity control feature turns on a heater to help reduce

moisture on the door hinge seal. Use in humid environments or

when you notice moisture on the door hinge seal. The refrigerator

uses more energy when Humidity Control is on.

1. On the main menu, press the touch pad next to "Options."

2. Press the touch pad next to "Humid Ctrl Is On" to switch

between ON and OFR Press the touch pad next to "Done" to

lock in the desired setting and return to the main menu.

Vacation Mode

The vacation mode feature decreases the number of automatic

defrost cycles. Once set, vacation mode will remain on until a

door is opened or the feature is turned off on the control panel.

NOTE: Door openings are ignored for the first hour after Vacation

mode is activated.

1. On the main menu, press the touch pad next to "Options."

2. In each of the following screens, continue to press the touch

pad next to "More Options" until "Vac. Mode is Off" appears

on the display.

3. Press the touch pad next to "Vac. Mode is Off" to switch

between ON and OFR Press the touch pad next to "Done" to

lock in the desired setting and return to the main menu.

Max Cool

The Max Cool feature assists with periods of high refrigerator or

freezer use, full grocery loads, or temporarily warm room

temperatures by lowering the freezer and refrigerator to the

minimum temperatures.

1. On the main menu, press the touch pad next to "Options."

2. In each of the following screens, continue to press the touch

pad next to "More Options" until "Max Cool is Off" appears

on the display.

3. Press the touch pad next to "Max Cool is Off" to switch

between ON and OFE Press the touch pad next to "Done" to

lock in the desired setting and return to the main menu.

NOTE: The Max Cool feature will automatically shut off in

approximately 2 hours.

Sabbath Mode

The Sabbath mode feature turns off all lights, disables the water

and ice dispenser, disables all alarms and tones, disables the

automatic defrost feature and disables the control panel.

While the refrigerator is operating in Sabbath mode, any touch of

the control panel will display the Sabbath mode control which will

allow you to turn off the Sabbath mode feature.

Turn Sabbath mode on:

1. On the main menu, press the touch pad next to "Options."

2. In each of the following screens, continue to press the touch

pad next to "More Options" until "Sabbath Is Off" appears on

the display.

3. Press the touch pad next to "Sabbath Is Off" to switch

between ON and OFE Press the touch pad next to "Done" to

lock in the desired setting and return to the main menu.

Temp Alarm

The TempAlarm feature alerts you if the temperature exceeds

normal operating temperatures, for an hour or longer, in either or

both the refrigerator and freezer compartments. An audible alarm

will sound repeatedly and the highest temperature reached in

each compartment will be displayed.

NOTE: Touch any pad on the control panel to turn off the audible

alarm. Temp Alarm will automatically reset once the warm

condition has been corrected for 30 minutes.

1. On the main menu, press the touch pad next to "Options."

2. In each of the following screens, continue to press the touch

pad next to "More Options" until "Temp Alarm Is Off" appears

on the display.

3. Press the touch pad next to "Temp Alarm Is Off" to switch

between ON and OFE Press the touch pad next to "Done" to

lock in the desired setting and return to the main menu.

Replace H20 Filter

See "Water Filtration System."

User Settings

The control center allows you to set user preferences, if desired.

Language

The language preference allows you to change the control panel

display to English, French or Spanish.

1. On the main menu, press the touch pad next to "User

Settings."

2. Press the touch pad next to "Select Language."

3. Press the touch pad next to either "Mettre En Frangais" or

"Cambiar En Espar_ol." Press the touch pad next to "Confirm"

to lock in the setting and return to the main menu.

Temperature Display

The temperature display preference allows you to change the

control panel display from degrees Fahrenheit to degrees

Celsius.

1. On the main menu, press the touch pad next to "User

Settings."

2. Press the touch pad next to "Fahrenheit Is On" to switch

between Fahrenheit and Celsius. Press the touch pad next to

"Done" to lock in the desired setting and return to the main

menu.

Display Brightness

The Display Brightness preference adjusts the backlight level of

the control panel.

1. On the main menu, press the touch pad next to "User

Settings."

2. In each of the following screens, continue to press the touch

pad next to "More Settings" until "Display Brightness"

appears on the display.

3. Press the touch pad next to "Lighter" or "Darker" to adjust

the setting between 1 (darkest) and 5 (lightest). Press the

touch pad next to "Done" to lock in the desired setting and

return to the main menu.

Adjust Light Sensor

The "Adjust LiteSensor" preference allows you to adjust the level

at which the Light Sensor will detect darkness and activate the

Auto On mode for the dispenser light.

1. On the main menu, press the touch pad next to "User

Settings."

2. In each of the following screens, continue to press the touch

pad next to "More Settings" until "Adjust LiteSensor" appears

on the display.

3. Press the touch pad next to "Lighter" or "Darker" to adjust

the setting between 1 (darkest) and 9 (lightest). Press the

touch pad next to "Done" to lock in the desired setting.

Alarm Sound

The alarm sound preference allows you to turn off any audible

alarms (door open, too warm etc.) when quick and simple

remedies are not possible. It will not disable alarm features or

visual displays.

1. On the main menu, press the touch pad next to "User

Settings."

2. In each of the following screens, continue to press the touch

pad next to "More Settings" until "Alrm Sound Is On" appears

on the display.

3. Press the touch pad next to "Alrm Sound Is On" to switch

between ON and OFR Press the touch pad next to "Done" to

lock in the desired setting and return to the main menu.

% _ • _.. ,_ ,_ _•

Co,so......o©@_ !J ?l,,_,,_;÷

You can control the amount of humidity in the moisture-sealed

crisper. Depending on your model, adjust the control to any

setting between FRUIT and VEGETABLES or LOW and HIGH.

FRUIT / LOW (open) for best storage of fruits and vegetables

with skins,

VEGETABLES / HIGH (closed) for best storage of fresh, leafy

vegetables.

The ice maker and storage bin are located in the upper left-hand •

side of the refrigerator compartment.

Turning the Ice Maker On/Off

The On/Off switch is located on the side of the ice maker.

Toturn on the ice maker, press the switch to the ON position.

To manually turn off the ice maker, press the switch to the OFF

position.

NOTE: Your ice maker has an automatic shutoff. The ice maker

sensors will automatically stop ice production, but the control will

remain in the ON position.

Removing and Replacing Ice Storage Bin

To Remove the Ice Storage Bin:

1. Hold the base of the storage bin and press the release button

on the lower right.

2. Pull the storage bin out until resistance is felt. Lift up the front

of the ice bin and remove.

3. Press the switch to the OFF position

To Replace the Ice Storage Bin:

IMPORTANT: It may be necessary to turn the auger driver,

behind the ice bin, counterclockwise to properly align the ice bin

with the auger driver. The ice storage bin must be locked in place

for proper ice dispensing.

1. Press the switch to the ON position

2. Slide the ice bin into the guide rails located on either side of

the enclosure.

3. Push the ice bin in until resistance is felt. Raise the front •

slightly and push the ice bin in until an audible "click" is

heard.

A. ON position

B. Auger driver

Ice Production Rate

Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

The ice maker should produce approximately 8 to 12 batches

of ice in a 24-hour period.

To increase ice production, lower the freezer and refrigerator

temperature. See "Using the Controls." Wait 24 hours

between adjustments.

Remember

The quality of your ice will be only as good as the quality of

the water supplied to your ice maker. Avoid connecting the

ice maker to a softened water supply. Water softener

chemicals (such as salt) can damage parts of the ice maker

and lead to poor quality ice. If a softened water supply cannot

be avoided, make sure the water softener is operating

properly and is well maintained.

• Do not use anything sharp to break up the ice in the bin. This

can cause damage to the ice bin and dispenser mechanism.

• Do not store anything on top of the ice maker or in the ice

storage bin.

_ _.,7_,,_¸ _, _,,_ _ _y,_.,,_ _

IMPORTANT:

• After connecting the refrigerator to a water source, flush the

water system. Press the Water button on the control panel.

Use a sturdy container to depress and hold the dispenser

lever for 5 seconds, then release it for 5 seconds. Repeat

until water begins to flow. Once water begins to flow,

continue depressing and releasing the dispenser lever

(5 seconds on, 5 seconds off) for an additional 2 minutes.

This will flush air from the filter and water dispensing system.

Additional flushing may be required in some households. As

air is cleared from the system, water may spurt out of the

dispenser.

NOTE: After five minutes of continuous dispensing, the

dispenser will stop dispensing water to avoid flooding. To

continue dispensing, remove the container and press the

dispensing lever again.

Allow 24 hours for the refrigerator to cool down and chill

water. Dispense enough water every week to maintain a fresh

supply.

Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

Dispense Ice and Water

Cut Hazard

Use a sturdy glass when dispensing ice.

Failure to do so can result in cuts.

• The dispenser will dispense either water or cubed ice.

• Express Fill allows you to dispense water into containers that

will not fit within the dispenser area, such as sport bottles.

1. Select water or cubed ice by touching the word "WATER" or

"CUBES" on the control panel. The light above the control

indicates your selection.

[]

[Water]

[]

I Cubes

Press a sturdy container against the dispenser lever.

IMPORTANT: You do not need to apply a lot of pressure to

the lever in order to activate the dispenser. Pressing hard will

not make the water or ice dispense faster or in greater

quantities.

3. Remove the container to stop dispensing.

Dispenser Light

NOTES:

• The dispenser lights are LEDs which should not need to be

changed.

• When you use the dispenser, the lever will automatically turn

the light on. If you want the light to be on continuously, you

may choose either On or Auto.

Auto On

[] []

Auto: The light sensor monitors the light level in the room. The

dispenser light will illuminate at half-power when the light level is

low. To activate the Auto option press the Light button. The Auto

indicator light will illuminate.

On: For continuous light, press the Light button a second time.

The On indicator light will illuminate.

Off: To turn the dispenser light off, press the Light button a third

time.

Dispenser Lock

The dispenser can be locked for easy cleaning or to avoid

unintentional dispensing by small children and pets.

NOTE: The dispenser lock does not shut off power to the

product, to the ice maker, or to the dispenser light. It just

deactivates the dispenser lever.

To Lock and Unlock Dispenser:

Press and hold the LocWUnlock touch pad for three seconds to

lock the dispenser. The indicator light will illuminate when Lock is

on.

Press and hold the LocWUnlock touch pad again for

three seconds to unlock dispenser. The indicator light will turn

off.

[]

[Lock!Unlock[

hold 3 sec

wG$ef _;; Ol"o__'c}y$_6tN(

The water filter is located in the upper right-hand corner of the

refrigerator compartment.

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

Water Filter Status

The control panel will remind you when it is time to order and

replace your water filter by displaying a message when you

dispense water. "Order Water Filter" means it is almost time to

change the water filter and "Replace Water Filter" means a new

water filter should be installed. It is recommended that you

replace the water filter when you see the "Replace Water Filter"

message OR earlier if the flow of water to your water dispenser or

ice maker decreases noticeably.

Reset Water Filter Status

After replacing the water filter, you must reset the water filter

status to turn off the message.

1. On main menu, press the touch pad next to "Options."

2. In each of the following screens, continue to press the touch

pad next to "More Options" until you reach the "Replace

Filter screen."

3. Press the touch pad next to "YES" to reset the water filter

status. Press the touch pad next to "NO" if you do not wish to

reset the water filter status.

Replacing the Water Filter

To purchase a replacement water filter contact your dealer or call

1-877-232-6771 USA or f-800-807-6777 Canada.

IMPORTANT: Air trapped in the water system may cause water

and filter to eject. Always dispense water for at least 2 minutes

before removing the filter or blue bypass cap.

1. Turn filter counterclockwise to remove.

2. Remove sealing label from replacement filter and insert the

filter end into the filter head.

3. Turn the filter clockwise until it stops. Snap the filter cover

closed.

NOTE: The dispenser feature may be used without a water filter

installed. Your water will not be filtered. If this option is chosen,

replace the filter with the blue bypass cap.

REFRIGERATORCARE

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to avoid

buildup of odors. Wipe up spills immediately.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid odor

transfer and drying out of food, wrap or cover foods tightly.

To Clean Your Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning waxes,

concentrated detergents, bleaches or cleansers containing

petroleum products on plastic parts, interior and door liners or

gaskets. Do not use paper towels, scouring pads, or other harsh

cleaning tools.

f. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

3. Wash stainless steel and painted metal exteriors with a clean

sponge or soft cloth and a mild detergent in warm water.

• To keep your stainless steel refrigerator looking like new

and to remove minor scuffs or marks, it is suggested that

you use the manufacturer's approved Stainless Steel

Cleaner & Polish, Part Number 20000008. To order the

cleaner, call f-877-232-6771 U.S.A. or 1-800-807-8777

Canada.

IMPORTANT: This cleaner is for stainless steel parts only!

Do not allow the Stainless Steel Cleaner & Polish to come into

contact with any plastic parts such as the trim pieces,

dispenser covers or door gaskets. If unintentional contact

does occur, clean plastic part with a sponge and mild

detergent in warm water. Dry thoroughly with a soft cloth.

There is no need for routine condenser cleaning in normal

home operating environments. If the environment is

particularly greasy or dusty, or there is significant pet traffic in

the home, the condenser should be cleaned every 2 to

3 months to ensure maximum efficiency.

If you need to clean the condenser:

• Removethe base grille.

• Use a vacuum cleaner with a soft brush to clean the grille,

the open areas behind the grille and the front surface area

of the condenser.

• Replace the base grille when finished.

Plug in refrigerator or reconnect power.

NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to

replace the bulb with an appliance bulb of the same size, shape,

and wattage (no greater than 40 watts).

1. Unplug refrigerator or disconnect power.

2. Remove the light shield, if necessary.

• Top of the refrigerator compartment - Squeeze both sides

of the light shield while pulling downward to remove.

• Beneath ice storage enclosure - Press along upper edge

of light shield and roll light shield forward to remove.

3. Replace burned-out bulb(s) with appliance light bulb(s) no

greater than 40 watts.

4. Replace the light shield(s) by inserting the tabs on the shield

into the liner holes and snap into place.

NOTE: To avoid damaging the light shield, do not force the

shield beyond the locking point.

5. Plug in refrigerator or reconnect power.

TROUBLESHOOTING

Firsttry the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)

to possibly avoid the cost of a service call.

In the U.S.A., www.jennair.com In Canada, www.jennair.ca

The refrigerator will not operate

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Power cord unplugged? Plug into a grounded 3 prong

outlet.

• Is outlet working? Plug in a lamp to see if the outlet is

working.

• Household fuse blown or circuit breaker tripped? Replace

the fuse or reset the circuit breaker. If the problem continues,

call an electrician.

• Are controls on? Make sure the refrigerator controls are on.

See "Using the Controls."

• New installation? Allow 24 hours following installation for the

refrigerator to cool completely.

NOTE: Adjusting the temperature controls to coldest setting

will not cool either compartment more quickly.

The motor seems to run too much

Your new refrigerator may run longer than your old one due to its

high-efficiency compressor and fans. The unit may run even

longer if the room is warm, a large food load is added, doors are

opened often, or if the doors have been left open.

The refrigerator seems noisy

Refrigerator noise has been reduced over the years. Due to this

reduction, you may hear intermittent noises from your new

refrigerator that you did not notice from your old model. Below

are listed some normal sounds with explanations.

• Buzzing - heard when the water valve opens to fill the ice

maker

• Pulsating - fans/compressor adjusting to optimize

performance

• Hissing/Rattling - flow of refrigerant, movement of water

lines, or from items placed on top of the refrigerator

• Sizzling/Gurgling - water dripping on the heater during

defrost cycle

• Popping - contraction/expansion of inside walls, especially

during initial cool-down

• Water running - may be heard when water melts during the

defrost cycle and runs into the drain pan

• Creaking/Cracking - occurs as ice is being ejected from the

ice maker mold.

The doors will not close completely

• Door blocked open? Move food packages away from door.

• Bin or shelf in the way? Push bin or shelf back in the correct

position.

The doors are difficult to open

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

• Gaskets dirty or sticky? Clean gaskets and contact surfaces

with mild soap and warm water. Rinse and dry with soft cloth.

Temperature is too warm

• New installation? Allow 24 hours following installation for the

refrigerator to cool completely.

• Door(s) opened often or left open? Allows warm air to enter

refrigerator. Minimize door openings and keep doors fully

closed.

• Large load of food added? Allow several hours for

refrigerator to return to normal temperature.

• Controls set correctly for the surrounding conditions?

Adjust the controls a setting colder. Check temperature in

24 hours. See "Using the Controls."

There is interior moisture buildup

NOTE: Some moisture buildup is normal.

• Humid room? Contributes to moisture buildup.

• Door(s) opened often or left open? Allows humid air to

enter refrigerator. Minimize door openings and keep doors

fully closed.

The ice maker is not producing ice or not enough ice

• Refrigerator connected to a water supply and the supply

shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

• Kink in the water source line? A kink in the line can reduce

water flow. Straighten the water source line.

• Ice maker turned on? Make sure wire shutoff arm or switch

(depending on model) is in the ON position.

• New installation? Wait 24 hours after ice maker installation

for ice production to begin. Wait 72 hours for full ice

production.

• Freezer door closed completely? Firmly close the freezer

compartment door. If the freezer compartment door will not

close all the way, see "The doors will not close completely."

• Large amount of ice recently removed? Allow 24 hours for

ice maker to produce more ice.

• Ice cube jammed in the ice maker ejector arm?

Remove ice from the ejector arm with a plastic utensil.

Water filter installed on the refrigerator? Remove filter and

operate ice maker. If ice volume improves, then the filter may

be clogged or incorrectly installed. Replace filter or reinstall it

correctly.

• Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See "Water Supply Requirements."

The ice cubes are hollow or small

NOTE: This is an indication of low water pressure.

• Water shutoff valve not fully open? Turn the water shutoff

valve fully open.

• Kink in the water source line? A kink in the line can reduce

water flow. Straighten the water source line.

Water filter installed on the refrigerator? Remove filter and

operate ice maker. If ice quality improves, then the filter may

be clogged or incorrectly installed. Replace filter or reinstall it

correctly.

• Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure,

See "Water Supply Requirements,"

• Questions remain regarding water pressure? Call a

licensed, qualified plumber.

Off-taste, odor or gray color in the ice

• New plumbing connections? New plumbing connections

can cause discolored or off-flavored ice.

• Ice stored too long? Discard ice. Wash ice bin, Allow

24 hours for ice maker to make new ice.

• Odor transfer from food? Use airtight, moisture proof

packaging to store food,

• Are there minerals (such as sulfur) in the water? A water

filter may need to be installed to remove the minerals.

Water filter installed on the refrigerator? Gray or dark

discoloration in ice indicates that the water filtration system

needs additional flushing. Flush the water system before

using a new water filter. Replace water filter when indicated,

See "Water Filtration System."

The water and ice dispenser will not operate properly

• Refrigerator connected to a water supply and the supply

shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

• Kink in the water source line? Straighten the water source

lne,

• New installation? Flush and fill the water system. See "Water

and Ice Dispenser."

• Is the water pressure at least 35 psi (241 kPa)? The water

pressure to the home determines the flow from the dispenser.

See "Water Supply Requirements,"

Water filter installed on the refrigerator? Remove filter and

operate dispenser. If water flow increases, the filter may be

clogged or incorrectly installed. Replace filter or reinstall it

correctly.

• Refrigerator door closed completely? Close the door

firmly. If it does not close completely, see "The doors will not

close completely."

Recently removed the doors? Make sure the water

dispenser wire/tube assembly has been properly reconnected

at the bottom of the refrigerator door. See "Refrigerator

Doors."

• Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure,

See "Water Supply Requirements,"

Water is leaking from the dispenser system

NOTE: One or two drops of water after dispensing is normal.

• Glass not being held under the dispenser long enough?

Hold the glass under the dispenser 2 to 3 seconds after

releasing the dispenser lever.

New installation? Flush the water system. See "Water and

Ice Dispenser."

Recently changed water filter? Flush the water system. See

"Water and Ice Dispenser,"

Water on the floor near the base grille? Make sure the

water dispenser tube connections are fully tightened. See

"Refrigerator Doors."

Water from the dispenser is warm

NOTE: Water from the dispenser is only chilled to 50°F (10°C),

• New installation? Allow 24 hours after installation for the

water supply to cool completely,

• Recently dispensed large amount of water? Allow

24 hours for water supply to cool completely,

• Water not been recently dispensed? The first glass of water

may not be cool. Discard the first glass of water.

• Refrigerator connected to a cold water pipe? Make sure

the refrigerator is connected to a cold water pipe. See "Water

Supply Requirements."

WATERFILTERCERTIFICATIONS

State of Cab fomia

Department of Health Services

Water Treatment Device

Certificate Number

03- 1583

()ate Issued: Septombc,r 16 2/)03

[)ate Revised Ap ) ?_ 90()4

Trademark/Model Oeslr_nation Replacement Elements

UKF8001AXX7_0

409006-750

Rated Serv(ce Capacity: 75o gai Rated Servme FIo_ 0 78 gpm

Condttlons of Cer tificatlon:

Do lot us_ where _ater _s m_robluloglcalb _msaf_ o_ w_th _ ater _,f _mk_o_ _ qualily, except that _)S_eln_ ten ffwd _r

c) q redu_t_o_ may be _sed o_ d_sin_cterl v, awrs d_at may _Onl_m fll_rable cyst_

PRODUCTDATASHEETS

Interior Water Filtration System

Model UFK8001AXX-750 Capacity 750 Gallons (2839 Liters)

I System tested and certified by NSF International against NSF/ANSI

(_ Standard 42 for the reduction of Chlorine Taste and Odor, Particulate

Class I*; and against NSF/ANSl Standard 53 for the reduction of Lead,

Mercury, Atrazine, Benzene, p-Dichlorobenzene, Carbofuran,

Toxaphene, Cysts, Turbidity, Asbestos and Lindane.

This system has been tested according to NSF/ANSl Standards 42 and 53 for the reduction of the substances listed below. The

concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the

permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42 and 53.

Substance Reduction NSF Reduction Average Influent Challenge Maximum Average Minimum% Average%

Aesthetic Effects Requirements Influent Concentration Effluent Effluent Reduction Reduction

Chlorine Taste/Odor 50% reduction 1.88 mg/L 2.0 mg/L _+10% 0.06 mg/L ** 0.05 mg/L 96.84 >97.26

Particulate Class I* 85% reduction 5,700,000 #/mL Atpar_icles/mLleast10,000 69,000 #/mL 30,583 #/mL 98.94 99.52

Contaminant NSF Reduction Average Influent Challenge Maximum Average Minimum% Average%

Reduction Requirements Influent Concentration Effluent Effluent Reduction Reduction

Lead: (-®pH 6.5 0.010 mg/L 0.153 mg/L _ 0.15 mg/L _+10% < 0.001mg/L < 0.001mg/L >99.29% >99.35%

Lead: @pH 8.5 0.010 mg/L 0.150 mg/L t 0.15 mg/L _+10% < 0.001mg/L < 0.001mg/L >99.29% >99.33%

Mercury: @ pH 6.5 0.002 mg/L 0.006 mg/L 0.006 mg/L _+10% 0.0005 mg/L 0.0003 mg/L 90.91 95.70

Mercury: @ pH 8.5 0.002 mg/L 0.006 mg/L 0.006 mg/L _+10% 0.0015 mg/L 0.0008 mg/L 75.93 86.22

Benzene 0.005 mg/L 0.014 mg/L 0.015 mg/L _+10% 0.0011 mg/L 0.0006 mg/L 92.14% 95.71%

p-Dichlorobenzene 0.075 mg/L 0.208 mg/L 0.225 mg/L _+10% < 0.0005 mg/L < 0.0005 mg/L 99.74% 99.76%

Carbofuran 0.04 mg/L 0.081 mg/L 0.08 mg/L _+10% < 0.001mg/L < 0.001mg/L 98.46% 98.74%

Toxaphene 0.003 mg/L 0.015 mg/L 0.015 _+10% < 0.001mg/L < 0.001mg/L 91.67% 92.97%

Atrazine 0.003 mg/L 0.009mg/L 0.009 mg/L _+10% < 0.002 mg/L < 0.002 mg/L 75.31% 76.99%

Asbestos 99% 155 MF/L 107to 108fibers/L tt < 1 MF/L < 1 MF/L >99.99% >99.99%

Live Cysts _ >99.95% 166,500 #/L 50,000/L min. < 1 #/L _ < 1 #/L_ >99.99 >99.99

Turbidity 0.5 NTU 10.7 NTU 11 _+1 NTU 0.49 NTU 0.31 NTU 95.2 97.09

Lindane 0.0002 mg/L 0.002 mg/L 0.002 _+10% < 0.0001mg/L 0.000 mg/L 96.50% 98.72%

Test Parameters: pH = 7.5 _+0.5 unless otherwise noted. Flow = 0.78 gpm (1.9 Lpm). Pressure

71.6°F (20°C to 22°C).

• It is essential that operational, maintenance, and filter

replacement requirements be carried out for the product to

perform as advertised.

The filter monitor system measures the amount of water that

passes through the filter and alerts you to replace the filter.

When 90% of the filter's rated life is used, the yellow (Order)

light comes on. When 100% of the filter's rated life is used,

the red (Replace) light comes on, and it is recommended that

you replace the filter. For models without filter status lights,

replace the filter every 6 months. Use replacement filter

model UFK8001AXX-750. 2007 suggested retail price of

$49.99 U.S.A./S65.95 Canada. Prices are subject to change

without notice.

• The product is for cold water use only.

Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after

the system. Systems certified for cyst reduction may be used

on disinfected waters that may contain filterable cysts.

= 60 psig (413.7 kPa). Temp. = 68°F to

• Refer to the "Water Filtration System" section for the

Manufacturer's name and telephone number.

• Refer to the "Warranty" section for the Manufacturer's limited

warranty.

Application Guidelines/Water Supply Parameters

Water Supply City or Well

Water Pressure 35 - 120 psi (241 - 827 kPa)

Water Temperature 33 ° - 100°F (1° - 38°C)

Service Flow Rate 0.78 gpm (2.9 L/min.) @ 60 psi

*Class I particle size: >0.5 to <1 um

**Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.

tThese contaminants are not necessarily in your water supply. Performance may vary based on local water conditions.

ttFibers greater than 10 um in length

_Based on the use of Cryptosporidium parvum oocysts

® NSF is a registered trademark of NSF International.

JENN-AIR REFRIGERATORWARRANTY

ONE YEAR LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or

furnished with the product, Jenn-Air brand of Maytag Corporation or Maytag Limited (hereafter "Jenn-Air') will pay for factory specified

replacement parts and repair labor to correct defects in materials or workmanship. Service must be provided by a Jenn-Air designated

service company. This limited warranty applies only when the major appliance is used in the country in which it is purchased.

On models with a water filter: 30 day limited warranty on water filter. For 30 days from the date of purchase, when this filter is operated

and maintained according to instructions attached to or furnished with the product, Jenn-Air will pay for replacement parts to correct

defects in materials and workmanship.

SECOND THROUGH FIFTH YEAR LIMITED WARRANTY ON CAVITY LINER AND SEALED REFRIGERATION SYSTEM PARTS

In the second through fifth years from the date of purchase, when this major appliance is operated and maintained according to

instructions attached to or furnished with the product, Jenn-Air will pay for replacement or repair of the refrigerator/freezer cavity liner

(including labor costs) if the part cracks due to defective materials or workmanship. Also, in the second through fifth years from the date

of purchase, Jenn-Air will pay for factory specified parts and labor to correct defects in materials or workmanship in the sealed

refrigeration system. These parts are: compressor, evaporator, condenser, dryer, and connecting tubing. Service must be provided by a

Jenn-Air designated service company.

ITEMS JENN-AIR WILL NOT PAY FOR

1. Service calls to correct the installation of your major appliance, to instruct you how to use your major appliance, to replace or repair

house fuses or to correct house wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Those consumable parts are excluded from warranty

coverage.

3. Repairs when your major appliance is used for other than normal, single-family household use.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of products not approved by Jenn-Air.

5. Any food loss due to refrigerator or freezer product failures.

6. Replacement parts or repair labor costs for units operated outside the United States or Canada.

7. Pickup and delivery. This major appliance is designed to be repaired in the home.

8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

g. Expenses for travel and transportation for product service in remote locations.

10. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accordance with

published installation instructions.

11. Replacement parts or repair labor costs when the major appliance is used in a country other than the country in which it was

purchased.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED

HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. JENN-AIR SHALL NOT BE LIABLE FOR INCIDENTAL

OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF

INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES

YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATETO STATE OR PROVINCE

TO PROVINCE.

Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized Jenn-Air dealer to determine if another

warranty applies. 5/07

For additional product information, in the U.S.A., visit www.jennair.com

In Canada, visit www.jennair.ca

If you do not have access to the Internet and you need assistance using your product or you would like to schedule service, you may

contact Jenn-Air at the number below.

Have your complete model number ready. You can find your model number and serial number on the label located on the right-hand

side of the refrigerator interior.

For assistance or service in the U.S.A., call 1-800-688-1100. In Canada, call 1-800-807-6777.

If you need further assistance, you can write to Jenn-Air with any questions or concerns at the address below:

In the U.S.A.: In Canada:

Jenn-Air Brand Home Appliances Jenn-Air Brand Home Appliances

Customer eXperience Center Customer Interaction Centre

553 Benson Road 1901 Minnesota Court

Benton Harbor, M149022-2692 Mississauga, Ontario L5N 3A7

Please include a daytime phone number in your correspondence.

Please keep this User Instructions and model number information for future reference.

Nous vous REMERCIONS d'avoir achete ce produit de haute qualit& Si vous rencontrez un probleme non mentionne dans la section

DCPANNAGE, veuillez visiter notre site www.jennair.com pour des informations supplementaires. Si vous avez toujours besoin

d'assistance, veuillez nous telephoner au 1-800-688-1100. Au Canada, visitez notre site www.jennair.ca ou t616phonez-nous au

1-800-807-6777.

Vous aurez besoin de vos num6ros de module et de s6rie situ6s sur le c6t6 droit & I'int6rieur du r6frig6rateur.

SECURITEDUREFRIGERATEUR

Votre s_curit_ et celle des autres est tr_s importante.

Nous donnons de nombreux messages de securite importants dans ce manuel et sur votre appareil menager. Assurez-vous de

toujours lire tousles messages de securite et de vous y conformer.

Voici le symbole d'alerte de securit&

Ce symbole d'alerte de securite vous signale les dangers potentiels de deces et de blessures graves & vous

eta d'autres.

Tousles messages de securite suivront le symbole d'alerte de securite et le mot "DANGER" ou

"AVERTISSEMENT". Ces roots signifient :

Risque possible de deces ou de blessure grave si vous ne

suivez pas immediatement les instructions.

Risque possible de deces ou de blessure grave si vous

ne suivez pas les instructions.

Tous les messages de securite vous diront quel est le danger potentiel et vous disent comment reduire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

IMPORTANTES INSTRUCTIONS DE S¢:CURIT¢:

AVERTISSEMENT : Pour reduire les risques d'incendie, de choc electrique ou des blessures lots de I'utilisation du

refrigerateur, prendre quelques precautions fondamentales, y compris les suivantes :

• Brancher I'appareil sur une prise &3 alveoles reliee a la terre.

• Ne pas enlever la broche de liaison a la terre.

• Ne pas utiliser un adaptateur.

• Ne pas utiliser un c&ble de rallonge.

• Debrancher la source de courant electrique avant I'entretien.

• Replacer pieces et panneaux avant de faire la remise en marche.

• Enlever les portes de votre vieux refrigerateur.

• Utiliser un produit de nettoyage ininflammable.

• Garder les mat_riaux et les vapeurs inflammables, telle

que I'essence, loin du rdrigerateur.

• Utiliser deux ou plus de personnes pour deplacer et

installer le rdrigerateur.

• Debrancher le refrigerateur avant I'installation de la

machine a gla(_ons (seulement pour modeles pr_ts

recevoir une machine a glagons).

• Utiliser un verre robuste pour prendre des glagons (sur

certains modeles).

CONSERVEZ CES INSTRUCTIONS

Miseau rebutde votrevieux r( frig( rateur

Risque de suffoquer

Enlever les portes de votre vieux refrigerateur.

Le non=respect de cette instruction peut causer

un deces ou des lesions c_rebrales.

IMPORTANT : L'emprisonnement et I'etouffement des enfants ne

sont pas un probleme du passe. Les rdrigerateurs jetes ou

abandonnes sont encore dangereux, m_me s'ils sont laisses

abandonnes pendant "quelques jours seulement". Si vous vous

debarrassez de votre vieux refrigerateur, veuillez suivre les

instructions suivantes pour aider a eviter les accidents.

Avant de jeter votre vieux r_frig_rateur ou cong_lateur :

Enlever les portes.

Laisser les tablettes en place de sorte que les enfants ne

puissent pas y penetrer facilement.

INSTRUCTIONSD'INSTALLATION

Risque du poids excessif

Utiliser deux ou plus de personnes pour deplacer et

installer le r_frig_rateur.

Le non-respect de cette instruction peut causer

une blessure au dos ou d'autre blessure.

Enl_vement des mat_riaux d'emballage

Enlever le ruban adhesif et la colle des surfaces du

refrigerateur avant de le mettre en marche. Frotter une petite

quantite de savon liquide pour la vaisselle sur I'adhesif avec

les doigts. Rincer a I'eau tiede et essuyer.

Ne pas utiliser d'instruments coupants, d'alcool a friction, de

liquides inflammables ou de nettoyants abrasifs pour enlever

le ruban adhesif ou la colle. Ces produits peuvent

endommager la surface de votre refrigerateur. Pour plus de

renseignements, voir "Securite du refrigerateur".

• Jeter ou recycler tousles materiaux d'emballage.

Deplacement de votre refrigerateur :

Votre refrigerateur est Iourd. Lots du deplacement du

refrig6rateur pour le nettoyage ou le service, veiller a proteger

le plancher. Teujours tirer le refrigerateur tout droit Iors du

deplacement. Ne pas incliner le refrigerateur d'un c6te ou de

I'autre nile "faire marcher" en essayant de le deplacer car le

plancher pourrait _tre endommage.

Nettoyage avant rutilisation

Apres avoir enleve tousles materiaux d'emballage, nettoyer

I'interieur du refrigerateur avant de I'utiliser. Voir les instructions

de nettoyage dans "Entretien du refrigerateur".

Importants renseignements a savoir au sujet des tablettes

et des couvercles en verre :

Ne pas nettoyer les tablettes ou couvercles en verre avec de

I'eau tiede quand ils sont froids. Les tablettes et les

couvercles peuvent se briser s'ils sont exposes & des

changements soudains de temperature eu & un impact tel

que coup brusque. Pour votre protection, le verre trempe est

con_u pour eclater en d'innombrables pieces minuscules.

Ceci est normal. Les tablettes et les couvercles en verre sont

Iourds. Un soin special s'impose lots de leur deplacement

pour eviter I'impact d'une chute.

Risque d'explosion

Garder les materiaux et les vapeurs inflammables, telle

que I'essence, loin du refrigerateuro

Le non=respect de cette instruction peut causer

un deces, une explosion ou un incendie.

Pour assurer une ventilation convenable & votre refrig@ateur,

laisser un espace de 1/2"(1,25 cm) en haut et derriere le

refrig6rateur. Si votre refrigerateur comporte une machine

glagons, s'assurer qu'un espace additionnel est prevu a I'arriere

pour permettre les connexions des conduits d'eau. En cas

d'installation du refrig@ateur pres d'un mur fixe, laisser un

minimum de 23/4'' (7,0 cm) entre le refrig6rateur et lemur pour

permettre I'ouverture de la porte.

REMARQUE : II est recommande de ne pas installer le

rdrigerateur pres d'un four, d'un radiateur ou de toute autre

source de chaleur. Ne pas installer le rdrigerateur dans un

endroit ou la temp@ature baissera au-dessous de 55°F (13°C).

1/2" (1,25 cm)

Risque de choc electrique

Brancher sur une prise a 3 alveoles reliee a la terre.

Ne pas enlever la broche de liaison a la terre.

Ne pas utiliser un adaptateur.

Ne pas utiliser un c_ble de rallonge.

Le non-respect de ces instructions peut causer

un deces, un incendie ou un choc electrique.

Avant de placer le refrigerateur a son emplacement final, il est

important de vous assurer d'avoir la connexion electrique

appropriee.

M_thode recommand_e de raise _ la terre

Une source d'alimentation de 115 volts, 60 Hz, type 15 ou

20 amperes CA seulement, protegee par fusible et adequatement

mise a la terre, est necessaire. II est recommande d'utiliser un

circuit distinct pour alimenter uniquement votre refrig@ateur.

Utiliser une prise murale qui ne peut pas _tre mise hors circuit

I'aide d'un commutateur. Ne pas utiliser un c&ble de rallonge.

REMARQUE : Avant d'executer tout type d'installation,

nettoyage ou remplacement d'une ampoule d'eclairage, tourner

la commande (reglage du thermostat, du refrig@ateur ou du

congelateur selon le modele) a OFF (arr_t) et deconnecter ensuite

le refrigerateur de la source d'alimentation electrique. Lorsque

vous avez termine, reconnecter le refrig@ateur a la source

d'alimentation electrique et tourner de nouveau la commande

(reglage du thermostat, du refrigerateur ou du congelateur selon

le modele) au reglage desire. Voir "Utilisation des commandes".

23/4"(7,0cm)

La page est en cours de chargement...

Jenn-Air JFI2589AES10 Le manuel du propriétaire

Marque: Jenn-Air

Modèle: JFI2589AES10

Catégorie: Frigos

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Jenn-Air JFI2589AES10 Owner's manual

Jenn-Air JFI2589AES10 Le manuel du propriétaire

Jenn-Air JFI2589AES10 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents