Maytag Ice2O Series Manuel utilisateur

ImportnntSnfetvInstructions

What You Need to Know About

Safety Instructions

Warning and Important Safety Instructions appearing in

this guide are not meant to cover all possible

conditions and situations that may occur. Common

sense, caution and care must be exercised when

installing, maintaining or operating appliance.

Always contact the manufacturer about problems or

conditions you do not understand.

Recognize Safety Symbols, Words,

Labels

This appliance is equipped with a three-prong

grounded plug for your protection against possible

electrical shock hazards. It must be plugged into a

properly grounded wall receptacle. Where a standard

two-prong wall receptacle is encountered, it is the

personal responsibility and obligation of the customer

to have it replaced with a properly grounded three-

prong wall receptacle. Do not, under any

circumstances, cut or remove the third (ground)

prong from the power cord. Do not use an adapter

plug.

Power supply cord with

three-prong grounded plug

Properly

grounded type

wall receptacle

ImportnntSnfetvInstructions

SAVE TH ESE INSTRUCTIONS

QuickReference6aide

Orde_ Reptace

0 0 0

@ o

kY£AG

G

H

Quick Reference Guide See pages 10-11 for more information on controls.

iiiiiiiiiiiiiii_j_j!;

8i !ii!!

Hi!i!_

Temperature Control

Light Sensor

Reset Filter

Door Alarm

LocWUnlock

Water

Temp Alarm

Cube

Light

Max Cool

Vacation Mode

Use to control the temperature in the refrigerator and freezer compartments. Temperatures

are preset at the factory at 38° F (3° C) in the refrigerator compartment and 0° F (-18 ° C) in

the freezer compartment.

Senses light level within the room. Used with Autolight feature.

Use as a reminder to order or replace the filter.

Press and hold the pad for three seconds to reset lights.

Indicates a door has been left open.

To deactivate: close the door or press the pad.

Use to lock all functions.

To activate: press until green light illuminates.

To deactivate: press and hold the pad for three seconds until green light turns off.

Use to select water.

Use to alert if temperatures exceed normal range. Press once to stop audible alarm.

To deactivate: press and hold pad for three seconds.

Use to select ice.

Use to activate or deactivate the light. Press pad once for Auto, twice for Continuous or

three times to deactivate.

Use to quickly drop compartment temperatures to minimum settings.

To activate: press pad.

To deactivate: press pad again.

Use to defrost less frequently when you are away.

To activate: press the pad once.

To deactivate: press the pad again or open a door and the light will turn off.

Yourrefrigeratorwaspackedcarefullyforshipment.

Removeanddiscardshelfpackagingandtape.Do not

remove the serial plate.

Location

• Do not install refrigerator near oven, radiator or other

heat source. If not possible, shield refrigerator with

cabinet material (contact a qualified contractor).

• Do not install where temperature falls below 55° F

(13° C) or rises above 110° F (/43° C). Malfunction may

occur at this temperature.

• Refrigerator is designed for indoor household

application only.

Measuring the Opening

When installing your refrigerator, measure carefully.

Allow Y2"space at top and '/2"space behind the machine

compartment cover (located in the rear) for proper air

circulation.

Subflooring or floor coverings (i.e. carpet, tile, wood

floors, rugs) may make your opening smaller than

anticipated.

Some clearance may be gained by using the leveling

procedure under Leveling.

Important: If refrigerator is to be installed into a recess

where the top of the refrigerator is completely covered,

use distance from floor to top of hinge cap to verify

proper clearance.

Transporting Your Refrigerator

• NEVER transport refrigerator on its side. If an upright

position is not possible, lay refrigerator on its back.

Allow refrigerator to sit upright for approximately 30

minutes before plugging it in to assure oil returns to

the compressor. Plugging the refrigerator in

immediately may cause damage to internal parts.

• Use an appliance dolly when moving refrigerator.

ALWAYS truck refrigerator from its side or

back-NEVER from its front.

• Protect outside finish of refrigerator during transport

by wrapping cabinet in blankets or inserting padding

between the refrigerator and dolly.

• Secure refrigerator to dolly firmly with straps or

bungee cords. Thread straps through handles when

possible. Do not over-tighten. Over-tightening

restraints may dent or damage outside finish.

Leveling

To enhance the appearance and maintain performance,

the refrigerator should be leveled per instructions

below.

Notes:

• Complete any required water supply connection

before leveling.

• Some models only have adjustment screws '_,"

Materials Needed:

• %" hex head driver

• Carpenter's level.

1. Remove toe grille.

.

• Grasp firmly and pull

outward to unclip.

Using hex head driver, turn

the front adjustment screws (A) on each side to

raise or lower the front of the refrigerator (see

illustration below).

Using the hex head driver, turn each of these

adjustment screws (B) to raise or lower the rear of

the refrigerator.

Using a carpenter's level, make sure front of

refrigerator is '/4" (6 ram) or '/2bubble higher than

back of refrigerator and that the refrigerator is level

from side to side.

5. Turn stabilizing legs (C) clockwise until firmly

against floor.

6. Turn adjustment screws (A) counterclockwise to

allow the full weight of the refrigerator to rest on

the stabilizing legs.

c

7 Replace the toe grille.

Installation

• Align the toe grille mounting clips with the lower

cabinet slots.

• Push the toe grille firmly until it snaps into place.

Door and Drawer Removal

Some installations require door/drawer removal to

transport the refrigerator to its final location.

.

Lift right side

refrigerator door from

center hinge pin.

Remove door closure

from center hinge pin

on the right side and

retain for later use.

right

side

door

closure

Note: For refrigerators in operation, shut off water

before disconnecting water line from the door.

.

2.

3.

Unplug power cord from power source.

Remove toe grille (see page 4).

Remove top hinge cover

from right side refrigerator

door by removing Phillips

screw. Retain screw and

cover for later use.

.

10.

4. Unscrew _,6"hex head

screws from top hinge to

remove hinge and retain

all screws for later use.

11.

12.

Remove top hinge cover

from left side refrigerator

door by removing Phillips

screw. Retain screw and

cover for later use.

Disconnect wire harness

on top left side of

refrigerator door top

hinge. Release connector

by pressing junction

point with a flat blade

screwdriver or fingernail.

Disconnect ware rline.

Hold "tabbed" section of

waterline while rotating

the black locking collar

clockwise and slide back.

Unscrew -_,6"hex head

screws from top hinge to

remove hinge; retain for

later use.

Lift left side refrigerator

door, along with top hinge,

from center hinge pin.

Remove Phillips screws to

remove right and left hinges;

retain all screws for later

use.

Remove both stabilizing

brackets with _" hex

head driver; retain

screws for later use.

Installation

Door Reinstallation

1. Install hinge assemblies:

• Install center hinges with Phillips or hex screws.

2. Place hinge side of refrigerator

door on center hinge pin.

• Install top hinge with 5/,6"hex

head screws.

3. While holding refrigerator door upright, tighten

down top hinge with _,6" hex head driver.

4. Reconnect connector.

5. Connect the waterline tubes firmly by pushing one

waterline inside the other.

6. Slide the black locking collar fully forward.

7. Hold tabbed section of

waterline.

8. Rotate black locking collar

counterclockwise locking

water lines in place. A

tabs

"click" is heard ensuring

waterlines are correctly

locked in place. The "arrow"

on the tabbed section

should align with the 2 bars

on the black locking collar. .

9. Ensure the connection does not leak before

installing the upper hinge cover.

10. Replace top hinge covers.

Pullout Freezer Drawer

To Remove:

1. Pull drawer open to full

extension.

2. Slide freezer bins forward and

lift straight out.

3. Remove Phillips screws from

each of the drawer slides.

'_iiiiiiiii}ii{{i}ii_ii!;!i!i_i{_i!i!iiii'i¸!¸¸¸_¸¸ i

, , 4ii

.

Lift top of drawer front to

unhook the drawer from the

slides.

5. Move drawer slides fully

forward.

6. Lift out lower drawer assembly.

To Install:

1. Pull both rails out to

full extension.

2. While supporting

door front, hook

supports into slots

located on inside of

each slide.

Plastic Handle

To Remove:

1. Grasp the lower part of the handle

firmly, slide up, lift and remove

from the surface.

To Install:

1. The handles are to be oriented as

shown.

2. Align door handle clip with the

door studs.

Note: All four drawer bracket supports must be in

the proper slots for the drawer to function properly.

(See inset for detail.)

.

4.

Lower door front into final position.

Replace and tighten Phillips screws that were

removed from the drawer

slides.

5_

Install the lower assembly

by aligning hooks of lower

drawer assembly with rear

rail on freezer drawer.

6. Replace freezer bins. Align

the large square notches

on outside of the drawer

slides.

Handles

Note: If not installed, the handle is located in the

interior of the fresh food compartment or attached

to the back of your refrigerator.

3. Ensure the large hole in the

mounting clip is positioned

down on both ends of the

handle.

4. Rotate the handle so that the

handle is flat against the door.

5. Grasp the handle firmly and slide

down.

Freezer Handle

Notes:

• Select models have a slight

curve to the freezer handle.

• For proper installation, be sure

handle is oriented as shown.

Door

Stud

To Install:

1. Align door handle clips

to the studs attached to

the freezer door.

2. Ensure the large hole in

the mounting clip is

positioned to the right

on both ends of the

handle.

3. Rotate the handle so that the handle is flat against

the door.

4. Grasp the handle firmly and slide handle to the

right.

To Remove:

1. With both hands, firmly grasp the handle toward

the right side.

2. Slide toward the left, lift and remove from the

surface.

Metal Handle

Materials Needed:

• 3/32"Allen wrench

• Gloves to protect hands

I Note: Metal handles can scratch doors.

To Remove:

• Loosen set screws in

handle using 3/32,Allen

wrench.

• Repeat the procedure on

all screws.

To Replace:

• Align handle with the

mounting posts.

• Fully tighten all set

screws to secure handle

in place.

Connecting the Water Supply

I

Materials Needed:

• '/4"outer diameter flexible copper tubing

• Shut-off valve (requires a '/4"hole to be drilled into

water supply line before valve attachment)

• Adjustable wrenches (2)

• '//' hex nut driver

Notes:

Use copper tubing only for installation. Plastic is

less durable and can cause damage.

Add 8' to tubing length needed to reach water

supply for creation of service loop.

Create service loop with copper

tubing (minimum 2'

diameter). Avoid kinks in

the copper tubing when

bending it into a service

loop. Do not use plastic

tubing.

2' diameter

minimum

2. Remove plastic cap from water supply connection.

,

Place brass nut (A) and sleeve (B)

on copper tube end as illustrated.

Reminder: Do not use an old sleeve.

The nut and sleeve are provided in

the Use and Care packet.

A

/B

.

Place end of copper

tubing into water valve

supply line.

5. Slide brass nut over

sleeve and screw nut

into supply line.

(1) Place adjustable

wrench on nut attached

to plastic waterline and

maintain position.

(2) Using second

adjustable wrench turn

the upper nut clockwise

and fully tighten while holding the lower nut in

place.

Important: Do not over-tighten. Cross threading may

Occur,

tie

letainer

.

Pull on tubing to confirm

connection is secure. Connect

tubing to frame with water

tubing clamp (C). Slide

waterline into retainer, then

turn on water supply. Check

for leaks and correct if

necessary. Continue to

observe the water supply

connection for two to three

hours prior to moving the refrigerator to its

permanent location.

upply

7. Monitor water connection for 24 hours. Correct

leaks, if necessary.

Opening and Closing Your

Fresh Food Doors

Your new refrigerator is

uniquely designed with two

fresh food doors. Either door

can be opened or closed

independently of one another.

For proper usage and to

avoid possible damage,

always ensure the vertical

hinged section (on the left

fresh food door) remains

folded inward before closing

both doors. When both doors

are closed, the hinged section

automatically forms a seal between the two doors.

When the left door is opened, the vertical hinged

section automatically folds inward so that is is out of

the way.

UsingtheControls

Initial Temperature Setting

Temperatures are preset at the factory at 38 ° F (3° C)

in the refrigerator compartment and 0° F (-18 ° C) in

the freezer compartment.

Adjusting the Control

24 hours after adding food, you may decide that one or

both compartments should be colder or warmer. If so,

adjust the control as indicated in the Temperature

Control Guide below.

• Do not change either control more than one degree

at a time. Allow temperature to stabilize for 24 hours

before making a new temperature adjustment.

Temperature Control Guide

Refrigerator Set the refrigerator control to next

too cold higher number by pressing the (_

pad.

Refrigerator Set the refrigerator control to next

too warm lower number by pressing the (_

pad.

Freezer too Set the freezer control to next higher

cold number by pressing the _ pad.

Freezer too Set the freezer control to next lower

warm number by pressing the (_ pad.

Turn Press the freezer (_ pad until

refrigerator "OFF" appears in the display. Press

off the (_ in either the freezer or

refrigerator section to turn back on.

Water Reset Filter Status Indicator Light %; _....

When a water filter has been installed in the _-R_

refrigerator, the yellow Order light will

illuminate when the filter is 900/0used OR 11 months

have elapsed since the filter has been installed.

The red Replace light will illuminate when the filter is

1000/0used OR 12 months have elapsed since the filter

was installed. A new filter should be installed

immediately when the Replace light is illuminated.

After replacing the filter, press and hold the Reset Filter

pad for three seconds. The Order and Replace lights

will blink and then go off.

Light .... oo

The Light feature can be used to provide light

to the dispenser area. The light feature is

automatically activated and the indicator light

illuminates. There are two methods available for

lighting the dispenser - Auto and Continous.

The Auto light function activates the dispenser light at

half-powerwhen the light sensor detects that the light

levels in the room are low.

The Continuous light function provides light until

deactivated. The On indicator light will illuminate.

To Activate Auto Light:

Press the Light pad once. The Auto indicator will

illuminate.

To Activate Continuous Light:

Press Light pad again. The On indicator light will

illuminate.

To Deactivate Auto or Continuous Light:

Press the Light pad a thirdtime. This will turn off the

dispenser and indicator light.

Vacation Mode o

The Vacation Mode feature causes the freezer _'v_o_

to defrost less frequently, conserving energy.

The Vacation Mode indicator light will illuminate when

the feature is activated. To activate, press the Vacation

Mode pad. To deactivate, press the Vacation Mode

pad again OR open either door. The indicator light will

go off, and return to normal operating mode.

10

11

UsingtheControls

Notes:

• Door openings will not deactivate Vacation Mode

for approximately one hour after activation.

• If vacationing for more than a few days, see the

Preparing for Vacation section, page 25.

Temp Alarm o

The Temp Alarm system is designed to alert you if (T_ _

the freezer or refrigerator temperatures exceed

normal operating temperatures due to a power outage or

other event.

To Activate:

Press the Temp Alarm pad once. The Temp Alarm

indicator light will illuminate.

To Deactivate:

Press and hold the Temp Alarm pad for three seconds.

The indicator light will go off. If the alarm is not actively

showing an alarm condition, then the temp alarm pad

does not need to be held down for three seconds.

An Audible Alarm will sound repeatedly if the freezer or

refrigerator temperatures have exceeded normal operating

temperatures. The temperature display will alternately

show the current compartment temperatures and the

highest compartment temperatures reached when the

power was out, doors left slightly ajar, or system failures.

To Turn Off the Audible Alarm:

Press the Temp Alarm pad once. The Temp Alarm

indicator light will continue to flash and the temperatures

will alternate until the temperatures have stabilized.

Door Alarm

The Door Alarm feature will alert you when one of _")

the doors has been left open for approximately

three minutes. When this happens, the Door Alarm light

will flash and an audible alarm will sound.

To Activate:

Press the Door Alarm pad once. The Door Alarm

indicator light will illuminate.

To Deactivate:

Press the Door Alarm pad once. The indicator light will

go off.

To Turn Off the Audible Alarm:

Press the Door Alarm pad once or close the door.

Note: The light bulbs will all turn off if any door is

left open for six continuous minutes. Shutting all

three doors for one second will cause light bulbs to

come back on.

Max Cool

The Max Cool feature is automatically activated _"_4oao_"_

and the indicator light illuminates. This feature

provides the ability to cool down the refrigerator and

freezer after extended door openings or when loading

either compartment with warm food. This feature

causes the refrigerator and freezer temperatures to

drop to the minimum seetings on the control.

Important: When the Max Cool feature is in operation,

the _+_ and _L_ pads for the refrigerator and freezer

controls will not operate.

To Activate:

Press the Max Cool pad once. The Max Cool indicator

light will illuminate.

To Deactivate:

Press the Max Cool pad once. The indicator light will

go off.

Max Cool will deactivate automatically after 2 hours.

User Preferences

Access the User Preferences menu to:

• Change the temperature display from °F to °C.

• Enable or disable audible alarms.

• Adjust the light level at which the Dispenser Auto

Light will illuminate when this feature is activated on

the ice and water dispenser.

• Activate the Sabbath Mode.

To access the User Preferences menu, press and hold

the Door Alarm pad for three seconds. When in the

User Preferences mode, a short title for the feature will

appear in the Freezer temperature display and the

feature status will appear in the Refrigerator display.

1. Use the Freezer _;_ and _-_ control to scroll

through the features.

2. When the desired feature is displayed, use the

Refrigerator _ and _=_ control to change the

status.

3. When changes are complete, press the Door Alarm

pad for three seconds.

Temperature Display (F_C)

Change the display to show temperatures in degrees

Fahrenheit or degrees Celsius.

Alarm (AL)

When the Alarm mode is off, all tones will be disabled

until the feature is turned on (alarms are still enabled).

Auto Light Level Selection (LL)

This setting adjusts the light level at which the

dispenser light will illuminate when the sensor detects

IceandWater

that the light levels in the room are low. Setting 1 is

the darkest light level setting, setting 9 is the brightest

light level setting. Important: The Auto Light must be

activated on the ice and water dispenser control to

take advantage of this option.

Sabbath Mode (SAb)

When the Sabbath Mode is on, all control lights, interior

lights, night light, ice and water dispenser and alarm

tones will be disabled until the feature is turned off.

I Note: If the power fails, the control will remain in

Sabbath Mode when power returns.

Warm Cabinet Surfaces

At times, the front of the refrigerator cabinet and the

vertical hinged section of the door may be warm to the

touch. This is a normal occurrence that helps prevent

moisture from condensing on the cabinet. This

condition will be more noticeable when the refrigerator

is first started, during hot weather and after excessive

or lengthy door openings.

Note: During initial use of water dispenser and

ice maker, there will be a one to two minute delay

while water tank fills before water dispenses or ice

is made. Discard first 10-14 glasses of water after

initially connecting refrigerator to household water

supply. Additional flushing may be required in

some households where water is of poor quality.

Ice and Water Dispenser

To Use Dispenser

Paddle:

Removable Tray

• Choose Water selection

from dispenser control

panel.

• Press a sturdy,

wide-mouthed container

against dispenser paddle.

• Dispenser Light will

come on while paddle is

pressed.

• Release pressure on

dispenser paddle to stop

water dispensing. A small

amount of water may

continue to dispense and

collect in dispenser tray.

Large spills should be wiped dry.

Removable Tray

The removable tray at the bottom of the dispenser area

is designed to collect small spills and may be easily

removed for cleaning and emptying purposes.

Important: Removable tray does not drain. Do not

allow tray to overflow. If it does, remove tray and wipe

up overflow.

To Dispense Ice and Water:

• Select Water or Cube ice mode by pushing button

on dispenser control panel. A green light above

button indicates mode selection.

• Press container against dispenser paddle. When

dispensing ice, hold container as close to chute as

possible to reduce spraying.

Note: If dispenser is active for more than five

minutes, an automatic lock out sensor will shut

down power to dispenser area. See Dispenser

Lock/Unlock for unlocking information.

Dispenser Lock/Unlock o

The Dispenser LocWUnlock affects all _k_

keypad functions.

To Lock Dispenser:

• Press and hold the Lock/Unlock button for three

seconds. A green indicator light above the button will

illuminate when the dispenser is locked.

To Unlock Dispenser:

• Hold the Lock/Unlock button for three seconds. The

green indicator light above will go out.

Automatic Ice Maker

Connect the ice maker to the

water supply as instructed on

pages 8-9. A properly leveled

refrigerator is essential for

optimal ice maker

production.

Ice Storage Bin

The ice storage bin is

located below the

automatic ice maker in the

upper left side enclosure of

the fresh food

compartment.

To Remove:

• Depress the button on the lower right of

the ice storage bin to release from the enclosure.

Continue pulling until resistance is felt. Lift up front

of ice bin and remove. Press the switch on the front

of the ice maker to turn the ice maker off.

12

Iceu,dWmer

13

Important: Do not remove ice storage bin without

turning ice maker switch to OFE Removing ice storage

bin while ON could result in ice falling into the ice

storage bin enclosure, blocking the dispenser and

disabling the bin from being locked into proper

)osition.

Note: Access to the ice storage bin will be limited

with the left fresh food door opened at 90 degrees.

Move cabinet forward to enable door to open

sufficiently for ice storage bin access.

To Install:

(_o.

Important: Ice bin must be _°_

locked in place for proper ice

dispensing. If necessary, turn

auger driver behind ice bin

counterclockwise to properly align

ice bin with auger driver.

• Press the switch ON to activate

ice maker. Slide bin into guide rails located on either

side of the enclosure. Push the ice bin in until

resistance is felt. Raise the front slightly and push

the ice bin completely in. An audible "click" is

heard when the ice bin is located correctly.

Operating Instructions

• Confirm ice bin is in place.

• After freezer section reaches between 0° to 2° F (-18 °

to -17 ° C), ice maker fills with water and begins

operating. You will have a complete harvest of ice

approximately every hour.

• Allow approximately 3 to 6 hours after installation to

receive first harvest of ice.

• Discard ice created within the first 12 hours of

operation to verify system is flushed of impurities.

• Stop ice production by pressing the ON/OFF switch

located on the front of the ice maker.

• The first one or two batches will probably contain

undersized and irregular cubes because of air in the

supply line.

• When the ice cubes are ejected it is normal for

several cubes to be joined together at the ends. They

can easily be broken apart. The ice maker will

continue to make ice until the supply of ice cubes

raises the ice maker arm, shutting the ice maker off.

• Certain sounds may accompany the various cycles of

the ice maker. The motor may have a slight hum, the

cubes will rattle as they fall into an empty storage bin

and the water valve may click or "buzz" occasionally.

• If the ice is not used frequently, the ice cubes will

become cloudy, shrink, stick together and taste stale.

Empty the ice storage bin periodically and wash it in

lukewarm water. Be sure to dry the bin thoroughly

before replacing it.

• Beverages and foods should not be placed in the

ice storage bin for quick chilling. These items can

cause the ice maker to malfunction.

• Press the switch on the ice maker front to OFF when

the water supply is to be shut off for several hours.

WaterFilter

Water Filter Removal and

Installation

Initial Installation

The water filter is located

in the upper right-hand

corner of the fresh food

corn partment.

1. Remove blue bypass

cap and retain for

later use.

2. Remove sealing label from

end of filter and insert into

filter head.

3. Rotate gently clockwise

until filter stops. Snap filter

cover closed.

foward

Replacing Water Filter

Important: Air trapped in system may cause water

and cartridge to eject. Always dispense water for

at least 2 minutes before removing the filter or

blue bypass cap for any reason. Use caution when

removing.

1. Turn filter counterclockwise until it releases from

filter head.

2. Drain water from filter into sink, and dispose in

normal household trash.

3. Wipe up excess water in filter cover and continue

with Initial Installation, steps 2 and 3.

The filter should be changed at least every 12 months.

Important: Condition of water and amount used

determines life span of water filter cartridge. If water

use is high, or if water is of poor quality, replacement

may need to take place more often.

To purchase a replacement water filter cartridge,

contact your dealer or call 1-877-232-6771 U.S.A. or

1-800-688-8/408 Canada.

The dispenser feature may be used without a water

filter cartridge. If you choose this option, replace filter

with blue bypass cap.

State ol Calilomia

Dep artnlent ot Heahh Services

Water Treatment Device

Certificate Number

03- 1583

Daw Issued: September 16. 2003

Date Rcvi,',ed: April 22. 2004

Trademark/Model Desig,natioll Replacement Elements

UKFS001AXX75( UKFb;(_)I AXX

..... 750

67( 3523 750

Manufacturer: Pen{,lP/_rc Inc

_7003523

Organic contaminant's

Alla/llie

[Andane

[Jenzc'ne

Carb_)il_ran

dJ_hh)rt,ben/ene

Rated Service Capaci_: 750 gal Rated Service Flow: 078 _pm

Conditions of Certification:

I)o not use whele waler ix mi_lobiok/gically unsali_//1 wilh waler ol unknown qualily, excepl Ihat

systems cerfilScd I_r cyst redmlion may be used on disinlcc_ed watcls thai may contain filtclable

(ysls

14

WaterFilter

15

PuriCle

System Specification and Performance Data Sheet

Refrigerator Water Filter Cartridge Model UKF8001AXX

Specifications

Service Flow Rate (Maximum) .............................................0.78 GPM (2.9 L/min)

Rated Service Life UKF8001AXX-750 (Maximum) ......750 gallons/2838 liters

Maximum Operating Temperature .....................................100° F/38 ° C

Minimum Pressure Requirement ........................................35 psi/241 kPA

Minimum Operating Temperature ......................................33° F/1° C

Maximum Operating Pressure .............................................120 psi/827 kPA

1000 Apollo Road

Eagan, Minnesota 55121-2240

651.450.4913

EPA EST #35917-MN-1

Performance Data

Parameter

Chlorine

T&O

Particulate**

100834/B

USEPA

MCL

Standard No. 42: Aesthetic Effects

Influent

Challenge Concentration

2.0 mg/L ± 10%

Min. Required

Reduction

50%

Influent

Average

1.88 mg/L

5,700,000 #/nil

Effluent

Average Maximum

_0.05136364 mg/L 0.05 mg/L

30,583 #/ml 69,000 #/ml

% Reduction

Average Minimum

>97.26O/o 96.84%

99.52% 98.940/o

at least 10,000 particles/ml 85o/o

Parameter

Turbidity

Cysts

Asbestos

Lead at pH 6.5

Lead at pH 8.5

Mercury at pH 6.5

Mercury at pH 8.5

Atrazine

Benzene

Carbofuran

>Dichlorobenzene

Lindane

Toxaphene

USEPA

MCL

1 NTU**

99.5% Reduction

99% Reduction

0.015 mg/L

0.002 mg/L

0.003 mg/L

0.005 mg/L

0.04 mg/L

0.075 mg/L

0.0002 mg/L

0.003 mg/L

Standard No. 53: Health Effects

Influent

Challenge Concentration

11 ± 1 NTU***

Minimum 50.O00/L

10_10_fibers/L; fibers >10 micrometers in length

0.15 mg/L + 10%

.006 mg/L ± 10%

.005 mg/L ± 10%

O.OOgmg/L + 10%

0.015 mg/L ± 10%

0.08 mg/L ± 10%

.225 mg/L ± 10%

0.002 mg/L + 10%

0.015 ± 10o/o

Influent

Average

10.7 NTU

166,500 #/L

155 MF/L

0.153 mg/L

0.150 mg/L

0.006 mg/L

0.009 mg/L

0.014 mg/L

0.081 mg/L

0.208 mg/L

0.002 mg/L

0.015 mg/L

Effluent

Average Maximum

0.31 NTU .049 NTU

<1 #/L <1 #/L

<1 MF/L <1 MF/L

<.001 mg/L <.001 mg/L

0.0003 mg/L 0.0005 mg/L

0.0008 mg/L 0.0015 mg/L

<0.002 mg/L 0.002 mg/L

0.0006 mg/L 0.0011 mg/L

<0.001 mg/L <0.001 mg/L

<0.0005 mg/L <0.0005 mg/L

0.000 mg/L <0.0001 mg/L

<0.001 mg/L <0.001 mg/L

% Reduction

Average Minimum

97.09% 95.20%

>99.99% >99.99%

>99.35% >99.29o/o

>99.33% >99.29o/o

95.700/o 90.91%

86.22% 75.93%

76.99% 75.31%

95.71% 92.14%

98.74% 98.46%

99.76% 99.74%

98.72% 96.50%

92.97% 91.67%

Min. Required

Reduction

0.5 NTU

>99.95%

99%

0.10 mg/L

0.002 mg/L

0.003 mg/L

0.005 mg/L

0.04 mg/L

0.075 mg/L

0.0002 mg/L

0.003 mg/L

* Tested tising a flow rate of 0.78 gpm; pressure of 60 psig; pH of 7.5 + 0.5; temp. of

68° + 5° F (20 ° + 3° C)

** Measurement in Particles/ml. Particles used were 0.5 - 1 microns

*** NTU - Nephelonletric Turbidib_ Units

General Use Conditions

Read this Performance Data Sheet and compare the

capabilities of this unit with your actual water

treatment needs.

DO NOT use this product where water is

microbiologically unsafe or of unknown quality

without adequate disinfection before or after the

system. System certified for cyst reduction may be

used on disinfected water that may contain

filterable cysts.

USE ONLY WITH COLD WATER SUPPLY. CHECK

FOR COMPLIANCE WITH THE STATE AND LOCAL

LAWS AND REGULATIONS.

Tested and certified by NSF International against ANSI/NSF Standards 42 & 53

in models UKFS00tAXX-750 for the reduction of:

Standard No. 42: Aesthetic Effects Standard No. 53: Health Effects

Taste and Odor Reduction Chemical Reduction Unit

Chlorine Taste & Odor Lead, Atrazine, Lindane, Benzene,

Mechanical Filtration Unit Carbofuran, p-Dichlorobenzene, Mercury

Particulate Reduction Class 1 & Toxaphene Reduction

Mechanical Filtration Unit

Cyst, Turbidity and Asbestos Reduction

The PuriClean _II retractable water filtration system uses

UKF8001AXX replacement cartridge. Timely replacement

of filter cartridge is essential for performance satisfaction

from this filtration system. Please refer to the applicable

section of your Use and Care Guide for general operation,

maintenance requirements and troubleshooting.

Suggested retail price of replacement water filter is 539.99.

This system has been tested according to ANSI/NSF 42 and

53 for reduction of the substances listed above. The

concentration of the indicated substances in water entering

the system was reduced to a concentration less than or

equal to the permissible limit for water leaving the system,

as specified in ANSI/NSF 42 and 53.

FreshFoodFemures

Shelves

Spill-Catcher TM Glass Shelves

Your refrigerator has Spill-Catcher TM glass shelves. The

shelves have a spill retainer edge which allows for

easier clean up and some are equipped with a slide

out feature. To slide out, grasp the front of the shelf

and pull forward. Push in the shelf to return to the

original position.

To Remove a Shelf:

• Slightly tilt up the front and lift up

the rear of the shelf, then pull the

shelf straight out.

To Lock the Shelf into Another

Position:

• Tilt up the front edge of the shelf.

• Insert the hook into the desired frame openings and

let the shelf settle into place.

• Be sure the shelf is securely locked at the rear.

Elevator TM Shelf

The Elevator TM Shelf is equipped with a spill-retaining

edge and the EasyGlide TM slide-out feature. It can be

adjusted up or down without unloading.

To Slide Out EasyGlide TM Shelf:

• Grasp the front of the shelf and pull forward.

• Push the shelf in to return to original position.

To Adjust the Elevator TM Shelf:

• Pull out the knob on the crank handle.

• Rotate the crank clockwise to raise the shelf, and

counterclockwise to lower the height of the shelf.

To Remove Elevator TM Shelf:

• Completely unload the shelf and pull the shelf

forward.

Pull until the shelf stops.

Slightly tilt up the front and pull the shelf straight

out. Continue pulling forward until the shelf is clear

of the frame.

To Replace Elevator TM Shelf:

• Align the shelf to the frame and push it all the way

back.

In ordinary use, the Elevator TM Shelf frame assembly

does NOT require removal. Though unlikely, and not

recommended, the correct removal procedure is as

follows:

To Remove Frame Assembly:

• Unload the shelf completely.

• Slide the shelf forward about 2" and manually move

the two rear latches toward the shelf center.

• While supporting the entire shelf and frame from

underneath, lift slightly and rotate the assembly

approximately 30° to allow the rear mechanism to

clear the vertical rear side rails.

• The entire assembly can then be moved forward and

clear of the refrigerator compartment.

To Reinstall Frame Assembly:

• Reverse the removal procedure. Be sure the shelf is

in a level position. When the sliding shelf is pushed

to the rear, it will reposition the rear latches to their

correct operating position.

(style may vary)

FrameAssembly

Slide Out

EasyGtidd '' Shelf

16

FreshFoodFeutures

17

Crisper Top

The crisper top serves as the lower fresh food shelf.

To Remove the Crisper Top:

• Remove crisper drawers.

• Place hand under the frame to push up the glass. Lift

glass out.

• Lift frame from fresh food liner rails.

To Install:

• Replace frame in fresh food liner rails.

• Carefully replace glass into frame.

Door Storage

Dairy Center

The dairy center provides

convenient door storage for

spreadable items such as butter

and margarine. This compartment

can be moved to different locations to accommodate

storage needs. To use the dairy center, raise the cover.

To Remove:

• Raise the cover, push upward and pull out.

To Install:

• Slide the dairy center in and push down until firmly

seated in the door liner.

Door Buckets

Door buckets can be moved to meet storage needs.

To Remove:

• Slide bucket up and pull straight out.

To Install:

• Slide bucket in and push down

until firmly seated in the door

liner.

Crisper Drawers

The crisper drawers provide a higher humidity

environment for fresh fruit and vegetable storage.

Controls

The crisper controls regulate the amount of humidity in

the crisper drawer. Slide the control toward the FRUIT

setting for produce with outer skins. Slide the control

toward the VEGETABLES setting for leafy produce.

i EGETABLES FRUITHUMID/TY CONTROLLED

To Remove:

• Pull drawer out to full extension. Tilt up front of

drawer and pull straight out.

To Install:

• Insert drawer into frame rails and push back into

place.

Note: For best results, keep the crisper drawers

tightly closed.

Wide-N-Fresh TM Drawer

The Wide-N-Fresh TM drawer is a full-width drawer with

adjustable temperature control. This drawer can be

used for large party trays, dell items, beverages or

miscellaneous items and features a divider to organize

the drawer into sections if desired.

There is a

temperature

control which

adjusts the

amount of cold

air allowed into

the drawer.

The control is

located on the right side of the drawer, under

the lid.

Set the control to the higher setting _ to provide a

normal fresh food temperature.

Set the drawer on the lower setting _ when a

temperature colder than the main fresh food

compartment is desired. Use the coldest setting when

storing meats.

Notes:

• Cold air directed to the drawer can decrease fresh

food temperature. Fresh food control may need to

be adjusted.

• Do not place leafy vegetables in the drawer.

Colder temperatures could damage leafy produce.

FreshFoodFeotures

To Remove Drawer:

• Lift lid. Pull drawer out to full extension. Tilt up front

of drawer and pull straight out.

To Install Drawer:

• Push metal glide rails to the back of the fresh food

compartment. Place drawer onto rails and slide

drawer back until it falls into place.

To Remove Divider:

• Pull drawer completely out and raise the front of the

divider to unhook it from the rear wall of the drawer,

then lift drawer out.

To Install Divider:

• Hook back of divider over rear wall of drawer and

lower into place.

Accessories

Egg Tray (style may vary)

The egg tray holds a "dozen-

plus" eggs. It can be removed

to carry to a work area or to

be washed.

Wine Trivet/Can Rack

The wine trivet/can rack accessory

fits in the Wide-N-Fresh TM drawer or

on a shelf.

Bottles or cans can be laid crosswise, or a single bottle

may be laid in the center depression.

FreezerFeatures

Built-in Door Organizer

The vertical organizer is located in the

fresh food section on the inside left

door. The organizer is designed to hold

six - 12oz. cans, 20oz. bottles, baby

bottles, or yogurt containers,

individually.

Temperature Controlled

Beverage Chiller

The beverage chiller keeps

beverages and other items cooler

than the rest of the fresh food

section. A cold air inlet allows air

from the freezer section to pass into

the beverage chiller. The beverage

chiller control is located on the right

wall of the fresh food compartment ..........

The control adjusts the amount of

cold air allowed into the beverage

chiller. For a cooler temperature in

the beverage chiller, slide the

control down.

To Remove:

• Slide bucket up and straight out.

Firmly hold each side of the

beverage chiller, lift up and

away from the door.

To install:

• Reverse above procedure.

Freezer Bin

To Remove:

• Pull drawer out to full extension and lift bins out to

re move.

To install:

• Slide bin into freezer. Make

sure the large square holes

along outer bin align with

square knobs on freezer

drawer.

Freezer Bin Divider

The freezer drawer features a divider in the bin to

organize the drawer into sections if desired.

Lower Freezer Drawer

Note: See pages 6-7 for complete information on

lower drawer and drawer removal. I

18

19

FoodStorageTips

Fresh Food Storage

• The fresh food compartment of a refrigerator should

be kept between 340-40 ° F (1°-4 ° C) with an

optimum temperature of 37° F (3° C). To check the

temperature, place an appliance thermometer in a

glass of water and place in the center of the fresh

food compartment. Check after 24 hours. If the

temperature is above 40° F (4° C) adjust the controls

as explained on page 10.

• Avoid overcrowding the fresh food shelves. This

reduces the circulation of air around the food and

results in uneven cooling.

Fruits and Vegetables

• Storage in the crisper drawers traps humidity to help

preserve the fruit and vegetable quality for longer

time periods (see page 17).

• Sort fruits and vegetables before storage and use

bruised or soft items first. Discard those showing

signs of decay.

• Always wrap odorous foods such as onions and

cabbage so the odor does not transfer to other foods.

• While vegetables need a certain amount of humidity

to remain fresh, too much humidity can shorten

storage times (especially leafy vegetables). Drain

vegetables well before storing.

• Wait to wash fresh produce until right before use.

Meat and Cheese

• Storage in Wide-N-Fresh TM drawer helps preserve

quality for longer time periods.

• Raw meat and poultry should be wrapped securely

so leakage and contamination of other foods or

surfaces does not Occur,

• Occasionally mold will develop on the surface of

hard cheeses (Swiss, Cheddar, Parmesan). Cut off at

least an inch around and below the moldy area. Keep

your knife or instrument out of the mold itself.

Do not try to save individual cheese slices, soft

cheese, cottage cheese, cream, sour cream or yogurt

when mold appears.

Dairy Food

For milk and cream, store in the Temperature

Controlled Beverage Chiller which is designed to

maintain a lower temperature for optimum freshness

and life.

Most dairy foods such as milk, yogurt, sour cream

and cottage cheese have freshness dates on their

cartons for appropriate length of storage. Store these

foods in the original carton and refrigerate

immediately after purchasing and after each use.

Frozen Food Storage

The freezer compartment of a refrigerator should be

kept at approximately 0° F (-18 ° C). To check the

temperature, place an appliance thermometer

between the frozen packages and check after 24

hours. If the temperature is above 0° F (-18 ° C),

adjust the control as described on page 10.

• A freezer operates more efficiently when it is at least

two-thirds full.

Packaging Foods for Freezing

To minimize dehydration and quality deterioration use

aluminum foil, freezer wrap, freezer bags or airtight

containers. Force as much air out of the packages as

possible and be sure they are tightly sealed. Trapped

air can cause the food to dry out, change color and

develop an off-flavor (freezer burn).

• Overwrap fresh meats and poultry with suitable

freezer wrap prior to freezing.

• Do not refreeze meat that has completely thawed.

Loading the Freezer

Avoid adding too much warm food to the freezer at

one time. This overloads the freezer, slows the rate of

freezing and can raise the temperature of frozen

foods.

• Leave space between the packages so cold air can

circulate freely, allowing food to freeze as quickly as

possible.

Avoid storing hard-to-freeze foods such as ice cream

and orange juice on the freezer door shelves. These

foods are best stored in the freezer interior where the

temperature varies less with door openings.

Refer to the Food Storage Chart on pages 20 and 21 for

approximate storage times.

La page charge ...

Maytag Ice2O Series Manuel utilisateur

Maytag Ice2O Series Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents