KitchenAid KHSU205WBA0 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KHSU205WBA0

Catégorie: Hottes

Taper: Le manuel du propriétaire

Ce manuel convient également à

KHSU265WBA0

l_itchen_kid _

30" (76.2 CM) AND 36" (91.4 CM)

SLIDE-OUT VENT HOOD

For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230 or visit our website at

www.kitchenaid.com

In Canada, for assistance, installation and service, call: 1-800-807-6777 or visit our website at www.Kitchenaid.ca

HOIIE D'ASPIRATION AVEC MODULE DE

COMMANDE EXTRACTIBLE DE 30" (76,2 CM)

ET 36" (91,4 CM)

Au Canada, pour assistance, installation ou service, composez le 1-800-807-6777 ou visitez notre site web & www,kitchenaid,ca

Table of Contents/Table des matieres ............................................................................ 2

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.

FOR RESIDENTIAL USE ONLY.

iMPORTANT : LIRE ET CONSERVER CES iNSTRUCTiONS.

POUR UTILISATION Rf-=SIDENTIELLE UNIQUEMENT.

W10267109A

TABLEOF CONTENTS

RANGE HOOD SAFETY ................................................................. 3

INSTALLATION REQUIREMENTS ................................................ 5

Tools and Parts ............................................................................ 5

Location Requirements ................................................................ 5

Venting Requirements .................................................................. 6

Electrical Requirements .............................................................. 8

INSTALLATION INSTRUCTIONS .................................................. 8

Prepare Location .......................................................................... 8

Install Range Hood ..................................................................... 11

Electrical Connection ................................................................. 12

Connect the Vent System .......................................................... 12

Optional Front Trim Kits ............................................................. 13

RANGE HOOD USE ...................................................................... 13

RANGE HOOD CARE ................................................................... 14

Cleaning ...................................................................................... 14

Replacing the Bulb ..................................................................... 14

WIRING DIAGRAM ....................................................................... 15

ASSISTANCE OR SERVICE ......................................................... 16

In the U.S.A................................................................................ 16

In Canada ................................................................................... 16

WARRANTY .................................................................................. 17

TABLEDES MATIERES

SI_CURITI_ DE LA HOTTE D'ASPIRATION ................................ 18

EXIGENCES D'INSTALLATION ................................................... 20

Outils et composants ................................................................. 20

Exigences d'emplacement ......................................................... 20

Exigences concernant I'evacuation ........................................... 21

Specifications electriques ......................................................... 22

INSTRUCTIONS D'INSTALLATION ............................................. 23

Preparation de I'emplacement ................................................... 23

Installation de la hotte ................................................................ 27

Raccordement electrique ........................................................... 27

Raccordement du circuit d'evacuation ...................................... 28

Ensembles de garniture avant (facultatifs)................................. 28

UTILISATION DE LA HOTTE ....................................................... 29

ENTRETIEN DE LA HOTTE .......................................................... 29

Nettoyage .................................................................................. 29

Remplacement de I'ampoule ..................................................... 30

SCHI_MAS DE C.&,BLAGE ........................................................... 31

ASSISTANCE OU SERVICE ......................................................... 31

Accessoires ................................................................................ 31

GARANTIE ..................................................................................... 32

RANGE HOOD SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING:

m Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer.

m Before servicing or cleaning the unit, switch power off at

service panel and lock the service disconnecting means to

prevent power from being switched on accidentally. When

the service disconnecting means cannot be locked,

securely fasten a prominent warning device, such as a tag,

to the service panel.

m Installation work and electrical wiring must be done by

qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction.

m Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer's guideline and safety

standards such as those published by the National Fire

Protection Association (NFPA), the American Society for

Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

m When cutting or drilling into wall or ceiling; do not damage

electrical wiring and other utilities.

m Ducted fans must always be vented outdoors.

CAUTION: For general ventilating use only. Do not use

to exhaust hazardous or explosive materials and vapors.

CAUTION: To reduce risk of fire and to properly exhaust

air, be sure to duct air outside - do not vent exhaust air into

spaces within walls or ceilings, attics or into crawl spaces,

or garages.

WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY

METAL DUCTWORK.

WARNING: TO REDUCE THE RISK OF A RANGE TOP

GREASE FIRE:

[] Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may

ignite. Heat oils slowly on low or medium settings.

[] Always turn hood ON when cooking at high heat or when

flambeing food (i.e. Crepes Suzette, Cherries Jubilee,

Peppercorn Beef Flamb6).

[] Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or filter.

[] Use proper pan size. Always use cookware appropriate for

the size of the surface element.

WARNING: TO REDUCE THE RISK OF INJURY TO

PERSONS IN THE EVENT OF A RANGE TOP GREASE

FIRE, OBSERVE THE FOLLOWING: a

[] SMOTHER FLAMES with a close fitting lid, cookie sheet, or

metal tray, then turn off the burner. BE CAREFUL TO

PREVENT BURNS. If the flames do not go out

immediately, EVACUATE AND CALL THE FIRE

DEPARTMENT.

[] NEVER PICK UP A FLAMING PAN - you may be burned.

[] DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result.

[] Use an extinguisher ONLY if:

- You know you have a class ABC extinguisher, and you

already know how to operate it.

- The fire is small and contained in the area where it

started.

- The fire department is being called.

- You can fight the fire with your back to an exit.

aBased on "Kitchen Fire Safety Tips" published by NFPA.

READ AND SAVE THESE iNSTRUCTiONS

INSTALLATION REQUIREMENTS

_?' i_: _ _._1:_t'i} Sa:O _"_*"

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

• Level

• Drill

• 1V4" drill bit

• 3/8"(8 mm) nut driver or ratchet

• Pencil

• Pliers

• Wire stripper or utility knife

• Tape measure or ruler

• Caulking gun and weatherproof caulking compound

• Phillips screwdriver

• Flat-blade screwdriver

• Saber or keyhole saw

• Vent clamps

• Metal snips

Parts needed

• Home power supply cable

• Two 1/2"(12.7 mm) UL listed or CSA approved strain reliefs

For vented installations, you will also needed:

• 1 wall or roof cap

• Metal vent system

For non-vented (recirculating) installations, you will also

need:

• Recirculation Kit Part Number 4396565. See "Assistance or

Service" section to order.

Optional parts needed:

• Wood filler strips for cabinets with recessed bottoms. Length

and thickness determined by recess dimensions. See

"Prepare Location" section.

• Two, 1" x 1" x 5" (25.4 x 25.4 x 127 mm) wood pieces for

cabinet floor. See "Prepare Location" section.

• Four, 1V4"(31.8 mm) wood screws

Parts supplied

Remove parts from packages. Check that all parts are included.

• 2 screws

• Damper

• Plastic cover (used for customized front panel)

• Hardware package

• Vent grate (for non-vented/recirculating installations)

• Front trim - White (installed), Black, and Brushed Aluminum

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the

installer's responsibility to comply with installation clearances

specified on the model/serial rating plate. The model/serial rating

plate is located behind the left filter on the rear wall of the range

hood.

Range hood location should be away from strong draft areas,

such as windows, doors, and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given

dimensions provide minimum clearance. Consult your cooktop/

range manufacturer installation instructions before making any

cutouts.

Grounded electrical outlet is required. See "Electrical

Requirements" section.

The range hood is factory set for vented installations through the

roof or wall. For non-vented (recirculating) installations see "Non-

Vented (recirculating) Installation Through the Soffit/Cabinet" in

the "Prepare Location" section. Recirculation Kit Part Number

4396565 is available from your dealer or an authorized parts

distributor.

All openings in ceiling and wall where range hood will be installed

must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local

codes.

Product Dimensions

9%" (24.8 cm)

5/8"

¾"(1.9cm)

25W' (64.1 cm) - 30" (76.2 cm) modem

31W' (79.4 cm) - 36" (91.4 cm) modem

297/8'' (75.9 cm) - 30" (76.2 cm) model

357/8'' (91.1 cm) - 36" (91.4 cm) modem

/,6"(4.0cm)

7.9

18" (45.7 cm) with screen extended

Cabinet Dimensions

15" (38.1 cm)

rain. cmearance

upper cabinet

to countertop

36" (91.4 cm)

base cabinet

height

• Vent system must terminate to the outside, except for non-

vented (recirculating) installations.

• Do not terminate the vent system in an attic or other enclosed

area.

• Do not use a 4" (10.2 cm) laundry-type wall caps.

• Use a metal vent only. A rigid metal vent is recommended.

Plastic or metal foil vent is not recommended.

• The length of vent system and number of elbows should be

kept to a minimum to provide efficient performance.

For the most efficient and quiet operation:

• Use no more than three 90° elbows.

• Make sure there is a minimum of 24" (61.0 cm) of straight

vent between the elbows if more than 1 elbow is used.

Do not install 2 elbows together.

The vent system must have a damper. If the roof or wall cap

has a damper, do not use the damper supplied with the range

hood.

• Use clamps to seal all joints in the vent system.

• Use caulking to seal exterior wall or roof opening around the

cap.

• The size of the vent should be uniform.

Cold weather installations

An additional back draft damper should be installed to minimize

backward cold air flow and athermal break should be installed to

minimize conduction of outside temperatures as part of the vent

system. The damper should be on the cold air side of the thermal

break.

The break should be as close as possible to where the vent

system enters the heated portion of the house.

Makeup air

Local building codes may require the use of makeup air systems

when using ventilation systems with greater than specified CFM

of air movement. The specified CFM varies from locale to locale.

Consult your HVAC professional for specific requirements in your

area.

Venting Methods

This range hood is factory set for venting through the roof or

through the wall.

The vent system needed for installation is not included.

A 6" (15.2 cm) round vent system is recommended.

Roof Venting Wall Venting

A. 6" (15.2 cm) vent through A. 6" (15.2 cm) vent through

the roof the wall

B.Roof cap B. Wall cap

Calculate Vent System Length

The recommended vent system is 6" (15.2 cm) round vent with a

maximum length of 26 ft (8 m). For the best performance, use no

more than three 90° elbows.

To calculate the length of the system, add the equivalent feet

(meters) for each of the vent pieces used in the system.

Vent Piece 6" (15.2 cm)

45° elbow 2.5 ft

(0.8m)

90° elbow 5.0 ft

(1.5m)

Example vent system - 6" (15.2 cm)

90 ° elbow

(0.ift__ j

6 ft (1.8 rn)

Wall cap

Maximum Length = 26 ft (8 m)

1 - 90° elbow = 5 ft (1.5 m)

1 - wall cap = 0 ft (0 m)

9 ft (2.8 m) straight = 9 ft (2.8 m)

System length = 14 ft (4.3 m)

Non-Vented (recirculating) Installations Through the Soffit/

Cabinet

If it is not possible to vent cooking fumes and vapors to the

outside, the range hood can be used in the non-vented

(recirculating) version, using an activated carbon filter.

Recirculation Kit Part Number 4396565 is available from the

dealer or an authorized parts distributor. Damper installation is

not required.

A. Ceiling

B. Vent cover

C. Soffit

D. 6" (15.2 cm) vent

E. Range hood

F. Cabinet

Observe all governing codes and ordinances. •

Ensure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA 70 (latest

edition), or CSA Standards C22.1-94, Canadian Electrical Code,

Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes

and ordinances.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association •

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road •

Cleveland, OH 44131-5575

• A 120 Volt, 60 Hz., AC only, 15-amp, fused electrical circuit is

required.

If the house has aluminum wiring, follow the procedure

below:

1. Connect a section of solid copper wire to the pigtail

leads.

2. Connect the aluminum wiring to the added section of

copper wire using special connectors and/or tools

designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended

procedure. Aluminum/copper connection must conform with

local codes and industry accepted wiring practices.

Wire sizes and connections must conform with the rating of

the appliance as specified on the model/serial rating plate.

The model/serial plate is located behind the filter on the rear

wall of the range hood.

Wire sizes must conform to the requirements of the National

Electrical Code, ANSI/NFPA 70 (latest edition), or CSA

Standards C22.1-94, Canadian Electrical Code, Part 1 and

C22.2 No. 0-M91 (latest edition) and all local codes and

ordinances.

INSTALLATION INSTRUCTIONS

It is recommended that the vent system be installed before the

range hood is installed.

Before making cutouts, make sure there is proper clearance

within the ceiling or wall for vent fittings.

1. Disconnect power.

2. Determine which venting method to use: roof, wall, or non-

vented.

3. Select a flat surface for assembling the range hood. Place

covering over that surface.

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

4. Using 2 or more people, lift range hood onto covered surface.

Range Hood Cabinet Cutout

1. Determine and clearly mark a centerline on the underside of

the cabinet.

••••••

A. Centerline

Measure and mark lines as shown for your size of range

hood. Use a saber saw or keyhole saw to cut an opening

through the underside of the cabinet.

13,/8 ==

(3.5cm)

////

30" (76.2 cm) hood - 125/8'' (32.0 cm)

36" (91.4 cm) hood - 155/8" (39.7 cm)

The finished cutout size will be:

30" (76.2 cm) range hood - 9_3/le'' x 251¼"(24.9 cm x 64.1 cm)

36" (91.4 cm) range hood - 9_3/le'' x 31W' (24.9 cm x 79.3 cm)

If the cabinet bottom is recessed above a support frame,

wood filler strips need to be installed on the right and left

sides of the cutout to provide sides of clearance for the

sliding screen. Wood filler strips should be flush with or

recessed 1/le"to %" (1.6 mm to 3.2 mm) from the bottom of

the support frame.

A. Wood filler strips

4. Complete cabinet preparation following the instructions for

your type of installation.

Venting Outside Through the Roof

Measure and mark the lines as shown. Use a saber saw or

keyhole saw to cut a round opening for the vent.

Transfer measurement A to the cabinet back wall. Measure

from the underside of the cabinet or wood filler strips, if used.

Mark the cutout as shown. Use a saber saw or keyhole saw

to cut a round opening for the vent.

A. Measurement A

B. Centerline

C. 6¼" (15.9 cm) round cutout

Change Hood to Optional Rear Exhaust

The hood comes from the factory with the exhaust collar on top

of the hood. The hood exhaust may be directed out the rear of

the hood through the exhaust collar.

Venting Outside Through the Wall

Assemble the vent that you will use over the vent opening. Do

not attach the vent at this time. Measure from the top of the

screen housing to the horizontal centerline of the vent

opening (A). Remove the vent.

!¢

A ''///' ..... [_

A. Rear exhaust

If you desire to have the hood exhaust out the rear, follow the

procedure below.

a.) Place the range hood on its back.

b.) Remove metal filters. See "Range Hood Care" section.

c.) Cut wire tie from wire bundle.

d.) Set the range hood back up to the upright position.

e.) Hold the blower motor to keep it from dropping while

removing the 4 screws holding the exhaust blower to the

range hood. Gently lower blower motor down.

f.) Remove the power supply cable and grommet from the

panel.

l . iI

A. Measurement A

A. Power supply cord and grommet

B. Blower mounting panel

g.) Remove the 12 screws from the blower mounting panel

and lift off the panel.

h.)Pulloutontheblowermotorandrotateit90°sothatthe

exhaustoutletispointingouttheback.Thenrotatethe

blowermotorarounditsexhaustaxis180°sotheflatside

oftheblowermotorispointedup.

NOTE:Thisistheonlywaytheblowermotorwillfit

properlyintheopening.

A. Rotate 90 °

B. Rotate 180°

C. Flat side of blower motor

i.) Check that the wiring is properly positioned.

j.) Place the power supply cable and grommet through the

center of the outlet hole opening in the mounting panel

and reposition the grommet into its mounting notch.

Non-Vented (recirculating) Installation Through the

Soffit/Cabinet

Measure and mark a round vent opening in the soffit using

the method shown for venting through the wall. Measure and

mark the centerline on the soffit above the range hood area.

A. Vent cover

B. Centerline

Use the vent cover included with the range hood or other vent

cover as a template to outline an opening for the vent. Use a

saber saw or keyhole saw to cut a round opening for the vent

system.

The range hood can be vented inside through the top of the

cabinet.

6W'

(15.9 crn)

A. Grommet/mounting notch

k.) Place the blower mounting panel over the exhaust outlet

and mount it onto the hood housing with the 12 mounting

screws. Tighten the screws.

I.) Pull the blower motor out through the opening in the

blower mounting panel and fasten with the 4 blower

mounting screws.

For non-vented (recirculating) installations, charcoal filters are

necessary. See the "Range Hood Care" section for

instructions on installing charcoal filters.

The Recirculation Kit Part Number 4396565 must be used.

5. Install the vent system according to the method needed. Use

caulking to seal the exterior wall or roof opening.

6. Run the wiring through the wall or cabinet according to the

national Electrical Code and all local codes and ordinances.

Use caulking to seal around wire opening.

Measure the thickness of the cabinet floor, including the filler

strips, if used. If the thickness is less than 5/8"(15.9 mm),

install wood filler strips that are a minimum length of

5" (12.7 cm) onto the cabinet floor. The mounting bracket

adjusts from %" (15.9 mm) to 21/8"(54.0 mm) for the wood

filler strips.

A. Less than %" (15.9 mm)

B. Wood fillers (thickness as required)

The spring loaded brackets are factory set to accommodate a

thickness between 13As"(3.0 cm) and 21¼'' (5.7 cm). If your

cabinet bottom is less than 1¾e" (3.0 cm) thick, the spring

loaded brackets can be removed and repositioned down from

the top setting (A), to the bottom setting (B), by removing the

4 Phillips screws.

...... _"J/P"

:_....

/\/o_ 0 .................................................B

....... ............................................A

g ................................................._ ..................................

A. Top setting - factory installed

B. Bottom setting

Place the round damper into the vent opening of the range

hood and press down. If the roof cap or wall cap has a

damper, do not attach the damper to the range hood.

10. Place the range hood on its back side on a covered surface.

a} Slide the range hood screen forward.

b} Remove the metal grease filters. See "Range Hood Care"

section.

c} Screw the mounting brackets up to the top position.

[

A. Mounting bracket screw

B. Flat-blade screwdriver

NOTE: For some non-vented (recirculating) installations it

may be easier to attach the vent system to the range hood

before lifting the range hood into its final location. Seal the

connection with clamps.

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

1. Using 2 or more people, lift the range hood into its final

position. (The wiring and terminal box are to be on top of the

range hood.)

2. Check that the mounting brackets overlap the cabinet bottom

or wood filler strips.

3. Center the range hood.

A. Damper

B. Range hood screen

C ........................... I;

o ©

A. Mounting bracket

B. Optional wood rifler strip

C. Cabinet bottom

D. Optional wood rifler strip for recessed cabinet

E. Slide-out range hood

Check that the front panel is parallel with the cabinet front

when the screen is pushed in. Slide the screen forward.

Tighten the mounting bracket screws so that the range hood

is secured to the cabinet.

A. Mounting bracket screw

B. Flat-blade screwdriver

Align the range hood front panel with the cabinet. Slide the

screen forward. Locate the 2 screws on each side and turn

them counterclockwise to loosen the screws. Adjust the front

of the vent vertically, 3/8"(9.5 mm) up or down, or horizontally,

3/4"(19 mm) front to back, until the front is flush with the

cabinet. Tighten the screws. If it is necessary to adjust the

given dimensions, lower and add or remove the filler strips or

redrill mounting holes.

A. Phillips screwdriver

B. Adjustment screws

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

1. Disconnect power.

2. Remove terminal box cover.

3. Remove knockout from top of the terminal box and install a

UL listed or CSA approved 1/2"strain relief.

4. Determine the location and mount the terminal box to the

inside of the cabinet or wall using the 4 mounting holes in the

back of the terminal box. (The mounting screws are not

supplied.)

5. Pull house power supply cable through the strain relief into

the terminal box.

6. Use UL listed wire connectors and connect black wires (D)

together.

7. Use UL listed wire connectors and connect white wires (A)

together.

B I

C ..........

A. White wires

B. Green ground screw

C. Ground wire

D.Black wires

E. Wireconnectors

Fire Hazard

Electrically ground the blower.

Use copper wire.

Connect ground wire to green ground screw in

terminal box.

Failure to do so can result in death, fire, or

electrical shock.

8. Connect the green (or bare) ground wire from the home

power supply to the green ground screw inside the range

hood terminal box. Tighten green ground screw.

Use caulking to seal around wire opening.

9. Tighten strain relief screw.

10. Install terminal box cover.

NOTE: Do not turn on power until installation is complete.

Vented Installations

1. Replace the metal filters. See "Range Hood Care" section.

2. Connect the vent system to the range hood vent opening.

Seal the connection with clamps.

3. Reconnect power.

4. Check the operation of the range hood fan and light.

5. Push the range hood screen back in.

Non-Vented (recirculating) Installations

1. Connect the vent system to the range hood vent opening.

Seal the connection with clamps.

2. Install charcoal filters. See "Range Hood Care" section.

3. Replace metal grease filters. See "Range Hood Care"

section.

4. Reconnect power.

5. Check the operation of the range hood fan and light.

6. Push the range hood screen back in.

To order replacement kits, see the "Assistance or Service"

section.

Install Front Trim Kit

1. Pull out on the range hood screen for access to the screws.

2. Remove metal grease filters. See "Range Hood Care"

section.

3. Remove the 3 mounting screws directly behind the front

panel.

White, black and brushed aluminum front trim for matching the

front panel to your range or cooktop color are included with the

range hood. The white trim is installed. See following instructions

to install a different trim color.

A. Three mounting screws

4. Remove existing trim piece and insert new trim piece.

5. Attach the new trim piece to the front panel using the

3 mounting screws. Tighten the screws.

6. Replace the metal grease filters. See "Range Hood Care"

section.

7. Push the range hood screen back in.

RANGE HOOD USE

The range hood is designed to remove smoke, cooking vapors and odors from the cooktop area. For best results, start the range hood

before cooking and allow it to operate several minutes after the cooking is complete to clear all smoke and odors from the kitchen.

Fan Control Light Control

Operating the Fan

1 !

Slide the range hood screen forward.

NOTE: When the screen is opened the fan will operate at the

fan switch setting that it was at when the screen was closed.

The fan will shutoff when the screen is about 2" (5.1 cm) from

the closed position.

Toturn fan On, move the fan switch from 0 (Off) to the desired

fan speed, 1 (Low), 2 (Medium), 3 (High).

NOTE: The speed may be increased, decreased, or turned off

at anytime during the range hood operation.

To turn the fan Off, move the fan switch to 0 (Off) or close the

screen.

NOTE: The fan will shut off when the screen is about

2" (5.1 cm) from the closed position. When the screen is

opened, the fan will operate at the last setting.

Operating the Light

1. Open the range hood screen.

2. To turn light On, move the switch from 0 (Off) to 1 (On).

NOTE: If the light switch is left in the 1 (On) position, the light

will be on each time the screen is opened. It can also be used

as a night light by opening the screen about 1" (2.5 cm).

3. Move the light switch to the 0 (Off) position or close the range

hood screen to turn the light Off.

RANGE HOOD CARE

IMPORTANT: Clean the range hood and grease filters frequently

according to the following instructions. Replace grease filters

before operating range hood.

Be sure light is cool before cleaning the range hood.

Exterior Surfaces

Clean the range hood with a mild detergent and soft cloth. To

avoid damage to the exterior surface, do not use abrasive

cleansers or steel-wool pads

Metal Grease Filters

The filters should be washed frequently. Place filters in

dishwasher or hot, soapy water to clean.

Drain water through edge holes and let each filter dry thoroughly

before replacing it.

To Remove Metal Grease Filters

1. Pull out on the range hood screen to expose the filters.

2. Using 2 hands, press in the tabs at each end of the metal filter

and pull down to remove it.

3. Repeat Step 2 for each filter.

To Install/Replace Charcoal Filters

1. Turn fan and lights off.

2. Remove all 4 metal grease filters. See "Metal Grease Filters"

section.

3. Set metal grease filters aside.

4. Rotate to the left (counterclockwise) and pull away from the

blower cover and discard filter pack. Repeat for other filter.

A 'ij

A. Filter

5. Place the charcoal filter against the blower cover and rotate

to the right (clockwise) to attach to cover.

6. Replace metal grease filters. See "Metal Grease Filters"

section.

Turn off the range hood and allow the bulb to cool.

Use a 15-watt fluorescent bulb with 30" (76.2 cm) unit and 18-

watt bulb with 36" (91.4 cm) unit.

1. Disconnect power.

2. Remove the screws from the cover clips at each end of the

light cover. Remove the cover clips and set them aside with

the screws.

\ \

To Replace Metal Grease Filters

1. Using 2 hands insert the metal filter into the filter openings.

2. Push the metal filter up and press in both tabs on the ends of

the filter. When filter is seated, release the tabs to lock in

place.

3. Repeat steps 1 and 2 for each filter.

Charcoal Filters - For Non-Vented (recirculating)

Installations

The charcoal filters are not washable nor reusable.

They should be changed every 6 months in normal use or more

frequently in heavy use. To order new charcoal filters, see the

"Assistance or Service" section.

A. Cover clips and screws

3. Slide the light cover all the way to the right. Lower the left end

of the cover below the support flange and slide it back to the

left to remove the cover.

4. Replace the light bulb.

5. Slide the cover back into position. Reinstall the cover clips

and screws. Tighten the screws.

The charcoal filters capture unpleasant cooking odors.

WIRING DIAGRAM

". /ill Bu

_--_

0 I 2 3

ASSISTANCE OR SERVICE

When calling for assistance or service, please know the purchase

date and the complete model and serial number of your

appliance. This information will help us to better respond to your

request.

If you need replacement parts

If you need to order replacement parts, we recommend that you

use only factory specified parts. Factory specified parts will fit

right and work right because they are made with the same

precision used to build every new appliance. To locate factory

specified replacement parts in your area, call us or your nearest

designated service center.

Call the KitchenAid Customer eXperience Center toll free:

1-800-422-1230.

Our consultants provide assistance with:

• Features and specifications on our full line of appliances.

• Installation information.

• Use and maintenance procedures.

• Accessory and repair parts sales.

• Specialized customer assistance (Spanish speaking, hearing

impaired, limited vision, etc.).

• Referrals to local dealers, repair parts distributors and service

companies. KitchenAid designated service technicians are

trained to fulfill the product warranty and provide after-

warranty service, anywhere in the United States.

To locate the KitchenAid designated service company in your

area, you can also look in your telephone directory Yellow

Pages.

For further assistance

If you need further assistance, you can write to KitchenAid with

any questions or concerns at:

KitchenAid Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Call the KitchenAid Canada Customer eXperience Centre toll

free: 1-800-807-6777.

Our consultants provide assistance with:

• Features and specifications on our full line of appliances.

• Use and maintenance procedures.

• Accessory and repair parts sales.

• Referrals to local dealers, repair parts distributors and service

companies. KitchenAid Canada designated service

technicians are trained to fulfill the product warranty and

provide after-warranty service, anywhere in Canada.

For further assistance

If you need further assistance, you can write to KitchenAid

Canada with any questions or concerns at:

Customer eXperience Centre

KitchenAid Canada

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

Please include a daytime phone number in your correspondence.

Recirculation Kit

(for non-vented installations only)

Order Part Number 4396565

Replacement Charcoal Filters

(for non-vented installations only)

Order Part Number 4378623

Please include a daytime phone number in your correspondence.

KITCHENAID ®VENTILATION WARRANTY

LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or

furnished with the product, KitchenAid brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter "KitchenAid") will pay for

Factory Specified Parts and repair labor to correct defects in materials or workmanship. Service must be provided by a KitchenAid

designated service company. This limited warranty is valid only in the United States or Canada and applies only when the major

appliance is used in the country in which it was purchased. Outside the 50 United States and Canada, this limited warranty does not

apply. Proof of original purchase date is required to obtain service under this limited warranty.

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty

coverage.

3. Repairs when your major appliance is used for other than normal, single-family household use or when it is used in a manner that is

contrary to published user or operator instructions and/or installation instructions.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of consumables or cleaning products not approved by KitchenAid.

5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported to KitchenAid within 30 days from the date of purchase.

6. Costs associated with the removal from your home of your major appliance for repairs. This major appliance is designed to be

repaired in the home and only in-home service is covered by this warranty.

7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized KitchenAid servicer is not available.

9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance

with published installation instructions.

10. Major appliances with original model/serial numbers that have been removed, altered or cannot be easily determined. This warranty

is void if the factory applied serial number has been altered or removed from your major appliance.

The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED

HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. KITCHENAID SHALL NOT BE LIABLE FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES

YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR PROVINCE

TO PROVINCE.

If outside the 50 United States and Canada, contact your authorized KitchenAid dealer to determine if another warranty applies.

If you need service, first see the "Troubleshooting" section of the Use & Care Guide. After checking "Troubleshooting," you may find

additional help by checking the "Assistance or Service" section or by calling KitchenAid. In the U.S.A., call 1-800-422-1230. In Canada,

call 1-800-807-6777. 9/07

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your major appliance

to better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the product.

Dealer name

Address

Phone number

Model number

Serial number

Purchase date

p p

SECURITE DE LA HOTTE D'ASPIRATION

Votre securite et celle des autres est tres importante.

Nous donnons de nombreux messages de securite importants dans ce manuel et sur votre appareil menager. Assurez-vous de

toujours lire tousles messages de securite et de vous y conformer.

Voici le symbole d'alerte de securit&

Ce symbole d'alerte de securite vous signale les dangers potentiels de deces et de blessures graves & vous

et & d'autres.

Tous les messages de securite suivront le symbole d'alerte de securite et le mot "DANGER" ou

"AVERTISSEMENT". Ces mots signifient •

Risque possible de d6cbs ou de blessure grave si vous ne

suivez pas imm6diatement les instructions.

Risque possible de d6cbs ou de blessure grave si vous

ne suivez pas les instructions.

Tousles messages de securite vous diront quel est le danger potentiel et vous disent comment reduire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

llVIPORTANTES iNSTRUCTiONS DE SI CURITI

AVERTISSEMENT : POUR REDUIRE LE RISQUE

D'INCENDIE, CHOC ¢:LECTRIQUE OU DOMMAGES

CORPORELS, RESPECTER LES INSTRUCTIONS

SUIVANTES :

m Utiliser cet appareil uniquement dans les applications

envisag6es par le fabricant. Pour toute question, contacter

le fabricant.

m Avant d'entreprendre un travail d'entretien ou de nettoyage,

interrompre I'alimentation de la hotte au niveau du tableau

de disjoncteurs, et verrouiller le tableau de disjoncteurs

pour emp6cher tout r@ablissement accidentel de

I'alimentation du circuit. Lorsqu'il n'est pas possible de

verrouiller le tableau de disjoncteurs, placer sur le tableau

de disjoncteurs une @iquette d'avertissement pro6minente

interdisant le r@ablissement de I'alimentation.

m Tout travail d'installation ou c&blage 61ectrique doit 6tre

r6alis6 par une personne qualifi6e, dans le respect des

prescriptions de tous les codes et normes applicables, y

compris les codes du b&timent et de protection contre les

incendies.

m Une source d'air de d6bit suffisant est n6cessaire pour le

fonctionnement correct de tout appareil & gaz (combustion

et 6vacuation des gaz &combustion par la chemin6e), pour

qu'il n'y ait pas de reflux des gaz de combustion. Respecter

les directives du fabricant de 1'6quipement de chauffage et

les prescriptions des normes de s6curit6 - comme celles

publi6es par la National Fire Protection Association (NFPA)

et I'American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), et les prescriptions des

autorites reglementaires locales.

m Lors d'op@ations de d6coupage et de perqage dans un mur

ou un plafond, veiller & ne pas endommager les c&blages

61ectriques ou canalisations qui peuvent s'y trouver.

m Les ventilateurs d'6vacuation doivent toujours d6charger

I'air & I'ext@ieur.

MISE EN GARDE : Cet appareil est con£:u uniquement

pour la ventilation g6n@ale. Ne pas I'utiliser pour I'extraction

de mati_res ou vapeurs dangereuses ou explosives.

MISE EN GARDE : Pour minimiser le risque d'incendie

et 6vacuer ad6quatement les gaz, veiller & acheminer I'air

aspir6 par un conduit jusqu'& I'ext@ieur - ne pas d6charger

I'air aspir6 dans un espace vide du b&timent comme une

cavit6 murale, un plafond, un grenier, un vide sanitaire ou

un garage.

AVERTISSEMENT : POUR R¢:DUIRE LE RISQUE

D'INCENDIE, UTILISER UNIQUEMENT DES CONDUITS

MI2TALLIQUES.

AVERTISSEMENT : POUR MINIMISER LE RISQUE

D'UN FEU DE GRAISSE SUR LA CUISINIF:RE :

[] Ne jamais laisser un 616ment de surface fonctionner &

puissance de chauffage maximale sans surveillance. Un

renversement/d6bordement de mati_re graisseuse pourrait

provoquer une inflammation et la g6n@ation de fum6e.

Utiliser une puissance de chauffage moyenne ou basse

pour le chauffage d'huile.

[] Veiller & toujours faire fonctionner le ventilateur de la hotte

Iors de la cuisson avec une puissance de chauffage 61ev6e

ou Iors de la cuisson d'un mets &flamber (& savoir cr6pes

Suzette, cerise jubil6e, steak au poivre flamb6).

[] Nettoyer fr6quemment les ventilateurs d'extraction. Veiller &

ne pas laisser la graisse s'accumuler sur les surfaces du

ventilateur ou des filtres.

[] Utiliser toujours un ustensile de taille appropri6e. Utiliser

toujours un ustensile adapt6 & la taille de 1'616ment

chauffant.

AVERTISSEMENT: POUR REDUIRE LE RISQUE DE

DOMMAGES CORPORELS APRF:S LE DECLENCHEMENT

D'UN FEU DE GRAISSE SUR LA CUISINI_:RE, APPLIQUER

LES RECOMMANDATIONS SUIVANTES :a

[] Placer sur le r6cipient un couvercle bien ajust6, une t61e &

biscuits ou un plateau m6tallique POUR ETOUFFER LES

FLAMMES, puis 6teindre le brt_leur. VEILLER ,&.¢:VITER

LES BRULURES. Si les flammes ne s'@eignent pas

imm6diatement, ¢:VACUER LA PIECE ET APPELER LES

POMPIERS.

[] NE JAMAIS PRENDRE EN MAIN UN RECIPIENT

ENFLAMME - vous risquez de vous brQler.

[] NE PAS UTILISER D'EAU, ni un torchon humide - ceci

pourrait provoquer une explosion de vapeur brQlante.

[] Utiliser un extincteur SEULEMENT si:

- IIs'agit d'un extincteur de classe ABC, dont on connaft le

fonctionnement.

- IIs'agit d'un petit feu encore limit6 & I'endroit oQ il s'est

d6clar&

- Les pompiers ont 6t6 contact6s.

- II est possible de garder le dos orient6 vers une sortie

pendant I'op@ation de lutte contre le feu.

aRecommandations tir6es des conseils de s6curit6 en cas

d'incendie de cuisine publi6s par la NFPA.

LIRE ET CONSERVER CES INSTRUCTIONS

EXIGENCES D'INSTALLATION

Rassembler les outils et composants necessaires avant

d'entreprendre I'installation. Lire et observer les instructions

fournies avec chacun des outils enumeres ci-dessous.

Outils n_cessaires

• Niveau

• Perceuse

• Foret de lY4"

• Tourne-ecrou ou cle a cliquet de 3/8"(8,0 mm)

• Crayon

• Pince

• Pince & denuder ou couteau utilitaire

• Metre-ruban ou regle

• Pistolet & calfeutrage et compose de calfeutrage resistant

aux intemperies

• Tournevis Phillips

• Tournevis & lame plate

• Scie sauteuse ou scie &guichet

• Brides de serrage pour conduit d'evacuation

• Cisaille de ferblantier

Pieces necessaires

• C&ble d'alimentation electrique du domicile

• Deux serre-c&ble approuves de 1/2"(12,7 mm) (homologation

UL ou CSA)

Pour les installations avec d_charge a I'ext_rieur, il faudra

aussi :

• 1 bouche de decharge (decharge a travers le mur ou &travers

le toit)

• Circuit d'evacuation metallique

Pour les installations sans d_charge a I'ext_rieur (recyclage),

il faudra aussi :

• Ensemble de recyclage, piece numero 4396565. Voir

"Assistance ou service" pour commander.

Pi_ces facultatives _ventuellement n_cessaires :

• Tringles d'appui en bois pour placards avec fond en retrait.

Longueur et epaisseur selon les dimensions de

I'encastrement. Voir la section "Preparation de

I'emplacement".

• Deux tringles de bois 1" x 1" x 5" (25,4 x 25,4 x 127,0 mm)

pour le plancher du placard. Voir la section "Preparation de

I'emplacement".

• Quatre vis & bois, 1Y4"(31,8 mm)

Pi_ces fournies

Retirer les pieces des emballages. Verifier que toutes les pieces

sont presentes.

• 2 vis

• Clapet

• Feuille de protection en plastique (pour panneau avant

personnalise)

• Sachet de quincaillerie

• Grille d'evacuation (pour les installations sans decharge

I'exterieur/recyclage)

• Garniture avant - blanche (preinstallee), noire et en aluminium

brosse

IMPORTANT : Observer les dispositions de tousles codes et

reglements en vigueur.

Confier I'installation de la hotte & un technicien qualifi& C'est &

I'installateur qu'incombe la responsabilite de respecter les

distances de separation exigees, specifiees sur la plaque

signaletique de I'appareil. La plaque signaletique de I'appareil est

situee derriere le filtre de gauche, sur la paroi arriere de la hotte.

Installer la hotte de cuisiniere a distance de toute zone exposee &

des courants d'air, comme fenetres, portes et bouches de

chauffage.

Respecter les dimensions indiquees pour les ouvertures

decouper dans les placards. Ces dimensions tiennent compte

des valeurs minimales des degagements de separation. Avant

d'effectuer des decoupages, consulter les instructions

d'installation de la table de cuisson/cuisiniere.

On doit disposer d'une prise de courant electrique reliee a la

terre. Voir la section "Specifications electriques".

La hotte a ete configuree a I'usine pour une installation avec

decharge a I'exterieur &travers le toit ou le mur. Pour une

installation sans decharge a I'exterieur (recyclage), voir

"Installation sans decharge a I'exterieur (recyclage) a travers le

soffite/placard", & la section "Preparation de I'emplacement".

L'ensemble de recyclage, piece numero 4396565, est disponible

chez votre marchand ou chez un distributeur de pieces autoris&

Assurer I'etancheite au niveau de chaque ouverture decoupee

dans le plafond ou lemur pour I'installation de la hotte de

CUlSlnlere.

Installation dans une r_sidence mobile

L'installation de cette hotte doit satisfaire aux exigences de la

norme Manufactured Home Construction Safety Standards, Titre

24 CFR, partie 328 (anciennement Federal Standard for Mobile

Home Construction and Safety, titre 24, HUD, partie 280); Iorsque

cette norme n'est pas applicable, I'installation doit satisfaire aux

criteres de la plus recente edition de la norme Manufactured

Home Installation 1982 (Manufactured Home Sites, Communities

and Setups)ANSI A225.1/NFPA 501A*, ou des codes Iocaux.

La page charge ...

KitchenAid KHSU205WBA0 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KHSU205WBA0

Catégorie: Hottes

Taper: Le manuel du propriétaire

Ce manuel convient également à

KHSU265WBA0

Télécharger le PDF

rapport

dans d''autres langues

English: KitchenAid KHSU205WBA0 Owner's manual

Documents connexes

Autres documents

Whirlpool Slide-Out Range Hood Manuel utilisateur