ESAB HW-9R Manuel utilisateur
- Catégorie
- Système de soudage
- Taper
- Manuel utilisateur
Ce manuel convient également à
HW-9, HW-9R, & HW-9F
TIG WELDING TORCHES
Covering the Hard Body, Silicone Rubber Body, and Flexible Head Models
Be sure this information reaches the operator.
You can get extra copies through your supplier.
These INSTRUCTIONS are for experienced operators. If you are not fully familiar with the principles of
operation and safe practices for arc welding equipment, we urge you to read our booklet, "Precautions and
Safe Practices for Arc Welding, Cutting, and Gouging", Form 52-529. Do NOT permit untrained persons to
install, operate, or maintain this equipment. Do NOT attempt to install or operate this equipment until you
have read and fully understand these instructions. If you do not fully understand these instructions, contact
your supplier for further information. Be sure to read the Safety Precautions (Section 1) before installing or
operating this equipment.
INSTRUCTION MANUAL
F-14-380-F
July, 2000
2
USER RESPONSIBILITY
This equipment will perform in conformity with the description thereof contained in this manual and accom-
panying labels and/or inserts when installed, operated, maintained and repaired in accordance with the instructions
provided. This equipment must be checked periodically. Malfunctioning or poorly maintained equipment should
not be used. Parts that are broken, missing, worn, distorted or contaminated should be replaced immediately.
Should such repair or replacement become necessary, the manufacturer recommends that a telephone or written
request for service advice be made to the Authorized Distributor from whom purchased.
This equipment or any of its parts should not be altered without the prior written approval of the manufac-
turer. The user of this equipment shall have the sole responsibility for any malfunction which results from improper
use, faulty maintenance, damage, improper repair or alteration by anyone other than the manufacturer or a service
facility designated by the manufacturer.
3
WARNING: These Safety Precautions are for
your protection. They summarize precaution-
ary information from the references listed in
Additional Safety Information section. Before
performing any installation or operating procedures, be
sure to read and follow the safety precautions listed below
as well as all other manuals, material safety data sheets,
labels, etc. Failure to observe Safety Precautions can result
in injury or death.
PROTECT YOURSELF AND OTHERS --
Some welding, cutting, and gouging
processes are noisy and require ear
protection. The arc, like the sun, emits
ultraviolet (UV) and other radiation and
can injure skin and eyes. Hot metal can cause burns.
Training in the proper use of the processes and equip-
ment is essential to prevent accidents. Therefore:
1. Always wear safety glasses with side shields in any work
area, even if welding helmets, face shields, and goggles
are also required.
2. Use a face shield fitted with the correct filter and cover
plates to protect your eyes, face, neck, and ears from
sparks and rays of the arc when operating or observing
operations. Warn bystanders not to watch the arc and
not to expose themselves to the rays of the electric-arc
or hot metal.
3. Wear flameproof gauntlet type gloves, heavy long-sleeve
shirt, cuffless trousers, high-topped shoes, and a weld-
ing helmet or cap for hair protection, to protect against
arc rays and hot sparks or hot metal. A flameproof apron
may also be desirable as protection against radiated
heat and sparks.
4. Hot sparks or metal can lodge in rolled up sleeves,
trouser cuffs, or pockets. Sleeves and collars should be
kept buttoned, and open pockets eliminated from the
front of clothing
5. Protect other personnel from arc rays and hot sparks
with a suitable non-flammable partition or curtains.
6. Use goggles over safety glasses when chipping slag or
grinding. Chipped slag may be hot and can fly far.
Bystanders should also wear goggles over safety glasses.
FIRES AND EXPLOSIONS -- Heat from
flames and arcs can start fires. Hot slag
or sparks can also cause fires and ex-
plosions. Therefore:
1. Remove all combustible materials well away from the
work area or cover the materials with a protective non-
flammable covering. Combustible materials include wood,
cloth, sawdust, liquid and gas fuels, solvents, paints and
coatings, paper, etc.
2. Hot sparks or hot metal can fall through cracks or
crevices in floors or wall openings and cause a hidden
smoldering fire or fires on the floor below. Make certain
that such openings are protected from hot sparks and
metal.“
3. Do not weld, cut or perform other hot work until the
workpiece has been completely cleaned so that there
are no substances on the workpiece which might pro-
duce flammable or toxic vapors. Do not do hot work on
closed containers. They may explode.
4. Have fire extinguishing equipment handy for instant use,
such as a garden hose, water pail, sand bucket, or
portable fire extinguisher. Be sure you are trained in its
use.
SAFETY PRECAUTIONS
10/98
5. Do not use equipment beyond its ratings. For example,
overloaded welding cable can overheat and create a fire
hazard.
6. After completing operations, inspect the work area to
make certain there are no hot sparks or hot metal which
could cause a later fire. Use fire watchers when neces-
sary.
7. For additional information, refer to NFPA Standard 51B,
"Fire Prevention in Use of Cutting and Welding Pro-
cesses", available from the National Fire Protection Asso-
ciation, Batterymarch Park, Quincy, MA 02269.
ELECTRICAL SHOCK -- Contact with live
electrical parts and ground can cause
severe injury or death. DO NOT use AC
welding current in damp areas, if move-
ment is confined, or if there is danger of
falling.
1. Be sure the power source frame (chassis) is connected
to the ground system of the input power.
2. Connect the workpiece to a good electrical ground.
3. Connect the work cable to the workpiece. A poor or
missing connection can expose you or others to a fatal
shock.
4. Use well-maintained equipment. Replace worn or dam-
aged cables.
5. Keep everything dry, including clothing, work area, cables,
torch/electrode holder, and power source.
6. Make sure that all parts of your body are insulated from
work and from ground.
7. Do not stand directly on metal or the earth while working
in tight quarters or a damp area; stand on dry boards or
an insulating platform and wear rubber-soled shoes.
8. Put on dry, hole-free gloves before turning on the power.
9. Turn off the power before removing your gloves.
10. Refer to ANSI/ASC Standard Z49.1 (listed on next page)
for specific grounding recommendations. Do not mis-
take the work lead for a ground cable.
ELECTRIC AND MAGNETIC FIELDS —
May be dangerous. Electric current flow-
ing through any conductor causes lo-
calized Electric and Magnetic Fields
(EMF). Welding and cutting current cre-
ates EMF around welding cables and
welding machines. Therefore:
1. Welders having pacemakers should consult their physi-
cian before welding. EMF may interfere with some pace-
makers.
2. Exposure to EMF may have other health effects which are
unknown.
3. Welders should use the following procedures to minimize
exposure to EMF:
A. Route the electrode and work cables together. Secure
them with tape when possible.
B. Never coil the torch or work cable around your body.
C. Do not place your body between the torch and work
cables. Route cables on the same side of your body.
D. Connect the work cable to the workpiece as close as
possible to the area being welded.
E. Keep welding power source and cables as far away
from your body as possible.
4
FUMES AND GASES -- Fumes and
gases, can cause discomfort or harm,
particularly in confined spaces. Do
not breathe fumes and gases. Shield-
ing gases can cause asphyxiation.
Therefore:
1. Always provide adequate ventilation in the work area by
natural or mechanical means. Do not weld, cut, or gouge
on materials such as galvanized steel, stainless steel,
copper, zinc, lead, beryllium, or cadmium unless posi-
tive mechanical ventilation is provided. Do not breathe
fumes from these materials.
2. Do not operate near degreasing and spraying opera-
tions. The heat or arc rays can react with chlorinated
hydrocarbon vapors to form phosgene, a highly toxic
gas, and other irritant gases.
3. If you develop momentary eye, nose, or throat irritation
while operating, this is an indication that ventilation is not
adequate. Stop work and take necessary steps to im-
prove ventilation in the work area. Do not continue to
operate if physical discomfort persists.
4. Refer to ANSI/ASC Standard Z49.1 (see listing below)
for specific ventilation recommendations.
5. WARNING: This product, when used for welding or
cutting, produces fumes or gases which
contain chemicals known to the State of
California to cause birth defects and, in
some cases, cancer. (California Health &
Safety Code
§25249.5 et seq.)
CYLINDER HANDLING -- Cylinders, if
mishandled, can rupture and violently
release gas. Sudden rupture of cylin-
der, valve, or relief device can injure or
kill. Therefore:
1. Use the proper gas for the process and use the proper
pressure reducing regulator designed to operate from
the compressed gas cylinder. Do not use adaptors.
Maintain hoses and fittings in good condition. Follow
manufacturer's operating instructions for mounting regu-
lator to a compressed gas cylinder.
2. Always secure cylinders in an upright position by chain
or strap to suitable hand trucks, undercarriages, benches,
walls, post, or racks. Never secure cylinders to work
tables or fixtures where they may become part of an
electrical circuit.
3. When not in use, keep cylinder valves closed. Have
valve protection cap in place if regulator is not con-
nected. Secure and move cylinders by using suitable
hand trucks. Avoid rough handling of cylinders.
4. Locate cylinders away from heat, sparks, and flames.
Never strike an arc on a cylinder.
5. For additional information, refer to CGA Standard P-1,
"Precautions for Safe Handling of Compressed Gases in
Cylinders", which is available from Compressed Gas
Association, 1235 Jefferson Davis Highway, Arlington,
VA 22202.
EQUIPMENT MAINTENANCE -- Faulty or
improperly maintained equipment can
cause injury or death. Therefore:
1. Always have qualified personnel perform the installa-
tion, troubleshooting, and maintenance work. Do not
perform any electrical work unless you are qualified to
perform such work.
2. Before performing any maintenance work inside a power
source, disconnect the power source from the incoming
electrical power.
3. Maintain cables, grounding wire, connections, power
cord, and power supply in safe working order. Do not
operate any equipment in faulty condition.
4. Do not abuse any equipment or accessories. Keep
equipment away from heat sources such as furnaces,
wet conditions such as water puddles, oil or grease,
corrosive atmospheres and inclement weather.
5. Keep all safety devices and cabinet covers in position
and in good repair.
6. Use equipment only for its intended purpose. Do not
modify it in any manner.
ADDITIONAL SAFETY INFORMATION -- For
more information on safe practices for elec-
tric arc welding and cutting equipment, ask
your supplier for a copy of "Precautions and
Safe Practices for Arc Welding, Cutting and
Gouging", Form 52-529.
The following publications, which are available from the
American Welding Society, 550 N.W. LeJuene Road, Mi-
ami, FL 33126, are recommended to you:
1. ANSI/ASC Z49.1 - "Safety in Welding and Cutting"
2. AWS C5.1 - "Recommended Practices for Plasma Arc
Welding"
3. AWS C5.2 - "Recommended Practices for Plasma Arc
Cutting"
4. AWS C5.3 - "Recommended Practices for Air Carbon
Arc Gouging and Cutting"
5. AWS C5.5 - "Recommended Practices for Gas Tung-
sten Arc Welding“
6. AWS C5.6 - "Recommended Practices for Gas Metal Arc
Welding"“
7. AWS SP - "Safe Practices" - Reprint, Welding Hand-
book.
8. ANSI/AWS F4.1, "Recommended Safe Practices for
Welding and Cutting of Containers That Have Held
Hazardous Substances."
MEANING OF SYMBOLS - As used through-
out this manual: Means Attention! Be Alert!
Your safety is involved.
Means immediate hazards which, if
not avoided, will result in immediate,
serious personal injury or loss of life.
Means potential hazards which could
result in personal injury or loss of life.
Means hazards which could result in
minor personal injury.
SP98-10
5
a. Éloigner suffisamment tous les matériaux combus-
tibles du secteur où l’on exécute des soudures ou des
coupes à l’arc, à moins de les recouvrir complètement
d’une bâche non-inflammable. Ce type de matériaux
comprend notamment le bois, les vêtements, la sciure,
l’essence, le kérosène, les peintures, les solvants, le
gaz naturel, l’acétylène, le propane et autres sub-
stances combustibles semblables.
b. Les étincelles ou les projections de métal incandes-
cent peuvent tomber dans des fissures du plancher ou
dans des ouvertures des murs et y déclencher une
ignition lente cachée. Veiller à protéger ces ouvertures
des étincelles et des projections de métal.
c. N’exécutez pas de soudures, de coupes, d’opérations
de gougeage ou autres travaux à chaud à la surface
de barils, bidons, réservoirs ou autres contenants
usagés, avant de les avoir nettoyés de toute trace de
substance susceptible de produire des vapeurs
inflammables ou toxiques.
d. En vue d’assurer la prévention des incendies, il
convient de disposer d’un matériel d’extinction prêt à
servir immédiatement, tel qu’un tuyau d’arrosage, un
seau à eau, un seau de sable ou un extincteur portatif.
e. Une fois le travail à l’arc terminé, inspectez le secteur
de façon à vous assurer qu’aucune étincelle ou projec-
tion de métal incandescent ne risque de provoquer
ultérieurement un feu.
3. CHOC ÉLECTRIQUE-- Le gougeage à l’arc et à l’arc
au plasma exige l’emploi de tensions à vide
relativement importantes; or, celles-ci risquent de
causer des dommages corporels graves et même
mortels en cas d’utilisation inadéquate. La gravité du
choc électrique reçu dépend du chemin suivi par le
courant à travers le corps humain et de son intensité.
a. Ne laissez jamais de surfaces métalliques sous ten-
sion venir au contact direct de la peau ou de
vêtements humides. Veillez à porter des gants bien
secs.
b. Si vous devez effectuer un travail sur une surface
métallique ou dans un secteur humide, veillez à assu-
rer votre isolation corporelle en portant des gants secs
et des chaussures à semelles de caoutchouc et en
vous tenant sur une planche ou une plate-forme
sèche.
c. Mettez toujours à la terre le poste de soudage/coupage
en le reliant par un câble à une bonne prise de terre.
d. N’utilisez jamais de câbles usés ou endommagés. Ne
surchargez jamais le câble. Utilisez toujours un
équipement correctement entretenu.
e. Mettez l’équipement hors tension lorsqu’il n’est pas en
service. une mise à la masse accidentelle peut en effet
provoquer une surchauffe de l’équipement et un dan-
ger d’incendie. Ne pas enrouler ou passer le câble
autour d’une partie quelconque du corps.
f. Vérifiez si le câble de masse est bien relié à la pièce en
un point aussi proche que possible de la zone de
travail. Le branchement des câbles de masse à
l’ossature du bâtiment ou en un point éloigné de la
zone de travail augmente en effet le risque de pas-
sage d’un courant de sortie par des chaînes delevage
PRÉCAUTIONS DE SÉCURITÉ
AVERTISSEMENT: Ces règles de sécurité ont pour objet
d’ assurer votre protection. Veillez à lire et à observer les
précautions énoncées ci-dessous avant de monter l’
équipement ou de commercer à l’utiliser. Tout défaut
d’observation de ces précautions risque d’entraîner des
blessures graves ou mortelles.
1. PROTECTION INDIVIDUELLE-- Les brûlures de la
peau et des yeux dues au rayonnement de l’arc
électrique ou du métal incandescent, lors du soudage
au plasma ou à l’électrode ou lors du gougeage à
l’arc, peuvent s’avérer plus graves que celles
résultant d’une exposition prolongée au soleil. Aussi
convient-il d’observer les précautions suivantes:
a. Portez un écran facial adéquat muni des plaques
protectrices et des verres filtrants appropriés afin de
vous protéger les yeux, le visage, le cou et les oreilles
des étincelles et du rayonnement de l’arc électrique
lorsque vous effectuez des soudures ou des coupes
ou lorsque vous en observez l’exécution.
AVERTISSEZ les personnes se trouvant à proximité
de façon à ce qu’elles ne regardent pas l’arc et à ce
qu’elles ne s’exposent pas à son rayonnement, ni à
celui du métal incandescent.
b. Portez des gants ignifugés à crispins, une tunique
épaisse à manches longues, des pantalons sans
rebord, des chaussures à embout d’acier et un
casque de soudage ou une calotte de protection, afin
d’éviter d’exposer la peau au rayonnement de l’arc
électrique ou du métal incandescent. ll est également
souhaitable d’utiliser un tablier ininflammable de
façon à se protéger des étincelles et du rayonnement
thermique.
c. Les étincelles ou les projections de métal incandes-
cent risquent de se loger dans des manches
retroussées, des bords relevés de pantalons ou dans
des poches. Aussi convient-il de garder boutonnés le
col et les manches et de porter des vêtements sans
poches à l’avant.
d. Protégez des étincelles et du rayonnement de l’arc
électrique les autres personnes travaillant à proximité
à l’aide d’un écran ininflammable adéquat.
e. Ne jamais omettre de porter des lunettes de sécurité
lorsque vous vous trouvez dans un secteur où l’on
effectue des opérations de soudage ou de coupage à
l’arc. Utilisez des lunettes de sécurité à écrans ou
verres latéraux pour piquer ou meûler le laitier. Les
piquetures incandescentes de laitier peuvent être
projetées à des distances considérables. Les
personnes se trouvant à proximité doivent également
porter des lunettes de protection.
f. Le gougeage à l’arc et le soudage à l’arc au plasma
produisent un niveau de bruit extrêmement élevé (de
100 à 114 dB) et exigent par conséquent l’emploi de
dispositifs appropriés de protection auditive.
2. PRÉVENTION DES INCENDES-- Les projections de
laitier incandescent ou d’étincelles peuvent
provoquer de graves incendies au contact de
matériaux combustibles solides, liquides ou gazeux.
Aussi faut-il observer les précautions suivantes:
9/97
6
des câbles de grue ou divers chemins électriques.
g. Empêchez l’apparition de toute humidité, notamment
sur vos vêtements, à la surface de l’emplacement de
travail, des câbles, du porte-électrode et du poste de
soudage/coupage. Réparez immédiatement toute
fuite d’eau.
4. VENTILATION-- La respiration prolongée des fumées
résultant des opérations de soudage/coupage, à
l’intérieur, d’un local clos, peut provoquer des mal-
aises et des dommages corporels. Aussi convient-il
d’observer les précautions suivantes:
a. Assurez en permanence une aération adéquate de
l’emplacement de travail en maintenant une ventila-
tion naturelle ou à l’aide de moyens mécaniques.
N’effectuez jamais de travaux de soudage ou de
coupage sur des matériaux de zinc, de plomb, de
beryllium ou de cadmium en l’absence de moyens
mécaniques de ventilation capables d’empêcher
l’inhalation des fumées dégagées par ces matériaux.
b. N’effectuez jamais de travaux de soudage ou de
coupage à proximité de vapeurs d’hydrocarbure
chloré résultant d’opérations voisines de dégraissage
ou de pulvérisation. La chaleur dégagée ou le
rayonnement de l’arc peut déclencher la formation de
phosgène -- gaz particulièrement toxique -- et d’autres
gaz irritants, à partir des vapeurs de solvant.
c. Une irritation momentanée des yeux, du nez ou de la
gorge constatée au cours de l’utilisation de
l’équipement dénote un défaut de ventilation. Arrêtez-
vous de travailler afin de prendre les mesures néces-
saires à l’amélioration de la ventilation. Ne poursuivez
pas l’opération entreprise si le malaise persiste.
d. Certaines commandes comportent des canalisations
où circule de l’hydrogène. L’armoire de commande est
munie d’un ventilateur destiné à empêcher la forma-
tion de poches d’hydrogène, lesquelles présentent un
danger d’explosion; ce ventilateur ne fonctionne que
si l’interrupteur correspondant du panneau avant se
trouve placé en position ON (Marche). Veillez à
manœuvrer cette commande en vérifiant si le
couvercle est bien en place, de façon à assurer
l’efficacité de la ventilation ainsi réalisée. Ne jamais
débrancher le ventilateur.
e. Les fumées produites par l’opération de soudage ou
de coupage peuvent s’avérer toxiques. Aussi est-il
nécessaire de disposer en permanence d’un dispositif
adéquat de ventilation de type aspirant, afin d’élimi-
ner du voisinage de l’opérateur tout dégagement de
fumée visible.
f. Consultez les recommandations particulières en
matière de ventilation indiquées à l’alinéa 6 de la
norme Z49.1 de l’AWS.
5. ENTRETIEN DE L’ÉQUIPEMENT-- Un équipement
entretenu de façon défectueuse ou inadéquate risque
non seulement de réaliser un travail de mauvaise
qualité mais, chose plus grave encore, d’entraîner des
dommages corporels graves, voire mortels en
déclenchant des incendies ou des chocs électriques.
Observez par conséquent les précautions suivantes:
a. Efforcez-vous de toujours confier à un personnel qua-
lifié l’installation, le dépannage et l’entretien du poste
de soudage et de coupage. N’effectuez aucune
réparation électrique sur l’équipement à moins d’être
qua-lifié à cet effet.
b. Ne procédez jamais à une tâche d’entretien
quelconque à l’intérieur du poste de soudage/
coupage, avant d’avoir débranché l’alimentation
électrique.
c. Maintenez en bon état de fonctionnement les câbles,
le câble de masse, les branchements, le cordon
d’alimentation et le poste de soudage/coupage.
N’utilisez jamais le poste ou l’équipement s’il présente
une défectuosité quelconque.
d. Prenez soin du poste de soudage et de coupage et des
équipements accessoires. Gardez-les à l’écart des
sources de charleur, notamment des fours, de
l’humidité, des flaques d’eau maintenez-les à l’abri des
traces d’huile ou de graisse, des atmosphères corro-
sives et des intempéries.
e. Laissez en place tous les dispositifs de sécurité et tous
les panneaux de l’armoire de commande en veillant à
les garder en bon état.
f. Utilisez le poste de soudage/coupage conformément à
son usage prévu et n’effectuez aucune modification.
6. INFORMATIONS COMPLÉMENTAIRES RELATIVES
À LA SÉCURITÉ--
Pour obtenir des informations complémentaires sur les
règles de sécurité à observer pour le montage et
l’utilisation d’équipements de soudage et de coupage
électriques et sur les méthodes de travail
recommandées, demandez un exemplaire du livret N°
52529 “Precautions and Safe Practices for Arc Weld-
ing, Cutting and Gouging” publié par ESAB. Nous
conseillons également de consulter les publications
sui-vantes, tenues à votre disposition par l’American
Welding Society, 550 N.W. LeJuene Road, Miami, FL
32126:
a. “Safety in Welding and Cutting” AWS Z49.1
b. “Recommended Safe Practices for Gas-Shielded Arc
Welding “AWS A6. 1.
c. “Safe Practices for Welding and Cutting Containers
That Have Held Combustibles” AWS-A6.0.
d. “Recommended Safe Practices for Plasma Arc Cutting”
AWS-A6. 3.
e. “Recommended Safe Practices for Plasma Arc Weld-
ing” AWS-C5. 1.
f. “Recommended Safe Practices for Air Carbon Arc
Gouging and Cutting” AWS-C5. 3.
g. “Code For Safety in Welding and Cutting”
CSA-Standard W117. 2.
9/97
7
SECTION 1
INTRODUCTION
1.5 Collets
Collets are available for each of the five electrode sizes.
The collet bodies come in both standard and gas lens
styles. See Table 1-2.
1.6 Cups
For use with standard collet bodies: standard ceramic
or high-impact ceramic. For use with gas lens collet
bodies: high-impact ceramic only. See Table 1-3.
1.7 Optional Accessories
A. Short Cap (41V33) for use with 2-in. electrodes;
long cap (41V24) for use with 7-in. electrodes.
B. Braided nylon sheath to protect service lines -
P/N 2075198 (9-ft long) and P/N 2075200 (20-ft
long).
C. Gas lens collet body wrench (59K07).
D. Tig Accessory Kit (999127) includes three collets,
three collet bodies, three 7-in. long 2% thoriated
electrodes (each in 1/16-in., 3/32-in., and 1/8-in.
sizes), three high impact cups (Nos. 5, 6, and 7),
and one long torch cap.
1.1 General
During DCSP operation, each torch in the HW-9 family is
rated at 120 A continuous duty and 140 A at 50% duty
cycle. During ACHF operation, each torch is rated at 85
A continuous duty and 100 A at 50% duty cycle. All the
torches are air-cooled.
1.2 Torch Dimensions
Overall Length .............................. 6-7/8 in. (175 mm)
Handle Diameter ................................ 3/4 in. (19 mm)
Head Diameter .................................. 3/4 in. (19 mm)
Height of Torch Head ................... 3-9/32 in. (83 mm)
- with Std. Medium Cap ................ 3-9/32 in. (83 mm)
- with Opt. Short Cap .................... 2-5/16 in. (59 mm)
- with Opt. Long Cap ................... 7-5/16 in. (186 mm)
Weight (less cable and hose) ........... 3.5 oz (100 gm)
Head Angle .................................................... 70 deg.
1.3 Required Accessories/Services
A. Collet, collet body, electrode, and cup. See
below.
B. Shielding gas regulator/flowmeter (if cylinder
gas is used) OR flowmeter (if gas is piped).
C. Gas hose, 12-1/2-ft long (P/N 40V77) or 25-ft
long (P/N 34V38) connects between regulator/
flowmeter and torch cable and hose assembly.
D. Welding power source and shielding gas supply.
E. Power Cable Adaptor (P/N 105Z57) for connect-
ing torch power cable to power source and gas
supply. Not required on HW-9R part numbers
34561 and 34562.
1.4 Electrodes
Each Torch model uses .020-inch thru 1/8-inch diameter
electrodes. The 2-inch, 3-inch, and 7-inch long standard
torch cap is designed for 3-inch electrodes. A short cap
for the 2-inch electrode and a long cap for the 7-inch
electrode are available as optional accessories. See
Table 1-1.
SECTION 1
INTRODUCTION
8
Table 1-1. Electrode and Cup Sizes for Different Welding Currents
Welding Currents (Amps)
ACHF* DCSP DCRP
Using pure Using Using pure or thoriated Electrode Diameter High-Impact Cup Ceramic Cup No.
tungsten thoriated electrodes tungsten electrodes in Inches No.
electrodes ***
5-15 5-20 5-20 --- .020 (0.5 mm) 4 4-5
10-60 15-80 15-80 --- .040 (1.0 mm) 4-5 4-5
50-100 70-150 70-150 10-20 1/16 (1.5 mm) 4-5-6 4-5-6
100-160** 140-235** 150-250** 15-30 3/32 (2.4 mm) 5-6-7-8 6-7-8
--- --- --- 25-40 1/8 (3.2 mm) 6-7-8-10 7-8-10
* The maximum current values shown in the table for ACHF have been determined using an unbalanced wave transformer. If a balanced wave transformer is
used, either reduce the maximum values in the table by about 30 per cent or use the next larger size electrode. This is necessary because of the higher heat
input to the electrode in a balanced wave setup.
NOTE: All current values are metered readings. Most transformers deliver about 15 per cent more current than shown on their scale readings.
** Exceeds the rated capacity of the torch.
*** Balled electrode tip ends can best be formed and maintained at these AC current levels.
Table 1-3. Gas Cups
Cup No. 4 5 6 7 8 10
High-Impact Cup 13N08 13N09 13N10 13N11 13N12 13N13
Ceramic Cup 13N14 13N15 13N16 13N17 13N18 13N19
Gas Lens High-Impact Cup 53N58 53N60 53N60 53N61 --- ---
Table 1-2. Collets and Collet Bodies
Size (In.) .020 .040 1/16 3/32 1/8
Collet 13N20 13N21 13N22 13N23 13N24
Collet Body 13N25 13N26 13N27 13N28 13N29
Gas Lens Collet Body* 45V41 45V42 45V43 45V44 45V45
* To prevent damage to gas lens in dc welding applications, use thoriated electrodes.
SECTION 2
INSTALLATION AND OPERATION
9
2.1 Setup and Installation
A. Connect the regulator/flowmeter to a gas cylin-
der. Refer to the instructions supplied with the
regulator/flowmeter for details on attaching
and adjusting the regulator.
B. Connect one end of the gas hose (P/N 40V77
or 34V38) to the regulator outlet and the other
end to the torch cable adaptor (105Z57).
C. Connect the power cable adaptor to the weld-
ing power source, either directly or through a
suitable length of welding cable fitted with lugs.
D. Install collet body, collet, electrode, and cup on
torch (see Figure 2-1) as follows:
1. Screw in collet body.
2. Screw on cup. (The gasket assembled to
the torch body, as supplied, will seal both
standard and gas lens cups. For welding in
argon chambers, this gasket, however, is
not suitable. See NOTE on parts drawing
for substitutions for chamber welding.)
3. Remove torch cap and slide collet into
position (tapered end first).
4. Slip electrode down through hole in top of
collet until end of electrode extends be-
yond rim of cup. (Exact extension is vari-
able from as little as 1/8 inch for butt
welding with standard collet bodies to 3/4
inch or more for corner or fillet welds with
gas lens collet bodies and cups.)
5. Screw on the torch cap and tighten. The
cap will press down on the collet to grip the
electrode securely. To readjust electrode,
loosen torch cap.
2.2 Operating Instructions
A. Make sure that all argon connections in the
system have been securely tightened and that
the torch cap has been well-tightened.
B. With the regulator flow-adjusting valve closed,
open the gas cylinder or station valve.
C. Set the power source for the desired welding
current.
Figure 2-1. Exploded View of HW-9
D. Open all shielding gas valves downstream
from the flowmeter or flowmeter/regulator (e.g.,
valve on torch, lever-operated shutoff valve, or
solenoid-operated valve in power source).
E. Set shielding gas flow to the desired level, as
registered on flowmeter tube or gauge.
NOTE
Purge the gas hose by allowing the gas to flow long
enough (up to 15 minutes on new torch; less than 5
minutes thereafter) to drive out air and moisture. This
will help prevent weld contamination.
F. Close control switch at work position or at
power source.
G. Draw a test arc on a heavy piece of scrap steel
or copper. (Do not use a carbon block. It will
tend to contaminate the electrode.)
H. If the test arc is satisfactory, commence weld-
ing.
(2) CAP "O" RING
MEDIUM TORCH CAP
3 INCH ELECTRODE
ELECTRODE COLLET
TORCH BODY
CUP GASKET
COLLET BODY
"O" RING
CUP
SECTION 3
MAINTENANCE
10
3.1 Maintenance
If this equipment does not operate properly, stop
work immediately and investigate the cause of the
malfunction. Maintenance work must be performed
by an experienced person and electrical work by a
trained electrician. Do not permit untrained per-
sons to inspect, clean, or repair this equipment.
Use only recommended GENUINE HELIARC re-
placement parts.
A. A poor shielding gas connection, or a leaky
hose, will not only waste gas but permit the
entry of minute amounts of air, sufficient to
contaminate both the electrode and the weld.
Trouble signs: a bluish cast on the electrode
after it has cooled; in welding aluminum, a dark
gray deposit on or beside the weld bead.
B. Keep the torch power cable away from hot
metal.
C. Do not try to repair concentric power cable,
replace it. Two piece cable and hose assem-
blies may be repaired using the repair kits
noted in parts breakdown. The kits include
replacement fittings and lug for the cable and
hose.
D. If an electrode becomes contaminated, shut
off power, then remove electrode from torch.
Break off the contaminated end (nicking with a
grinding wheel first will help) and replace elec-
trode.
E. Keep an eye on the sealing "O" ring on the torch
cap. If it shows signs of wear or distortion, cut
it off. Then install new ring (P/N 181W53) using
the assembly tool (P/N 13N42) supplied with
the torch. Apply a little silicone grease to the
new ring before attempting to slide it over the
tool and into the cap groove.
SECTION 4
4.1 Replacement Parts
The following illustrations of the HW-9, HW-9R, and
HW-9F Torch identify each replacement part by item
number as tabulated in the related parts list. The list
identifies each part by part number, description, and
quantity used.
4.2 Ordering
To assure proper operation, it is recommended that
only genuine ESAB parts and products be used with this
equipment. The use of non-ESAB parts may void your
warranty.
Replacement parts may be ordered from your ESAB
distributor or from:
ESAB Welding & Cutting Products
Attn: Customer Service
P.O. Box 100545
411 S. Ebenezer Road
Florence, SC 29501-0545
A. Give the part number, description and quantity
of each part required.
B. Give part number and description of equip-
ment on which the parts are to be used.
C. Indicate any special shipping instructions.
For technical assistance directly from an ESAB service
representative, call (803)664-4416. Additionally, ESAB
offers a toll free facsimile (FAX) service via 1-800-446-
5693.
PARTS
11
SECTION 4
PARTS
Figure 4-1. HW-9 Hard Body Torch Components
ITEM QTY. PART
NO. REQ. NO. DESCRIPTION
1 1 53N06 HANDLE
2 1 997022* POWER CABLE RUBBER (12-1/2 FT.)
1 997023* POWER CABLE RUBBER (25 FT.)
3 1 105Z57 POWER CABLE ADAPTER (Required Accessory)
4 1 598882 CUP GASKET (See Note in illustration above)
5 1 19686 BODY (includes “O” ring 85W49 & cup gasket 598882)
6 1 41V33 CAP, SHORT (includes “O” ring 181W53) (Optional)
7 1 41V35 CAP, MEDIUM (includes “O” ring 181W53)
8 1 41V24 CAP, LONG (includes “O” ring 181W53) (Optional)
Table 4-1. HW-9 Hard Body Assemblies
HW-9, 70 deg., 12-1/2 ft. 19684
HW-9, 70 deg., 25 ft. 19685
6
7
8
4 (See Note)
5
Gas Lens Access.
(See Tables 1-2, 1-3)
Standard Access.
(See Tables 1-2, 1-3)
3
2
1
NOTE: For chamber welding, replace 598882 with Gasket 598563 for stan-
dard cup, with “O”ring 526185 for gas lens cup.
*Optional PVC Power Cable 57Y01 (12 1/2 ft.); 57Y03 (25 ft.)
3/8 - 24
3/8 - 24
SECTION 4
PARTS
12
Figure 4-2. HW-9R Silicone Rubber Torch Components
ITEM QTY. PART
NO. REQ. NO. DESCRIPTION
1 1 105Z55R HANDLE, RIBBED
2 1 33946 TWO PIECE CABLE & HOSE ASSY. (12-1/2 FT.)
1 33947 TWO PIECE CABLE & HOSE ASSY. (25 FT.)
1 34651 REPAIR KIT FOR TWO PIECE CABLE & HOSE ASSY.
3 1 598882 CUP GASKET (See Note in illustration above)
4 1 34563 BODY W/VALVE (includes valve stem 19621)
1 19621 VALVE STEM (includes “O” ring 598869)
5 1 41V33 CAP, SHORT (includes “O” ring 181W53)
6 1 41V35 CAP, MEDIUM (includes “O” ring 181W53)
7 1 41V24 CAP, LONG (includes “O” ring 181W53)
8 1 19686 BODY
Table 4-2. HW-9R Silicone Rubber Assemblies
HW-9RV-2, 70 deg., 12-1/2 ft. 34561
HW-9RV-2, 70 deg., 25 ft. 34562
HW-9-2, 12-1/2 ft. 37740
HW-9-2, 25 ft. 37741
5
6
7
4
1
2
3 (See Note)
Lg. Dia.
Gas Lens
Access.
(See Tables 1-2, 1-3)
Standard Access.
(See Tables 1-2, 1-3)
NOTE: For chamber welding, replace 598882 with Gasket 598563 for stan-
dard cup, with “O”ring 526185 for gas lens cup.
3/8 - 24
5/8 - 18
8
13
SECTION 4
PARTS
Figure 4-3. HW-9AF Flexible Head Torch Components
ITEM QTY. PART
NO. REQ. NO. DESCRIPTION
1 1 105Z55 HANDLE
2 1 997022* POWER CABLE RUBBER (12-1/2 FT.)
1 997023* POWER CABLE RUBBER (25 FT.)
3 1 105Z57 POWER CABLE ADAPTOR (Required Accessory)
3 1 598882 CUP GASKET (See Note in illustration above.)
4 1 19924 BODY, FLEX
5 1 41V33 CAP, SHORT (includes “O” ring 181W53) (Optional)
6 1 41V35 CAP, MEDIUM (includes “O” ring 181W53)
7 1 41V24 CAP, LONG (includes “O” ring 181W53) (Optional)
6
7
8
1
2
3
Standard Access.
(See Tables 1-2, 1-3)
Gas Lens
Access.
(See Tables 1-2, 1-3)
NOTE: For chamber welding, replace 598882 with Gasket 598563 for stan-
dard cup, with “O”ring 526185 for gas lens cup.
Table 4-3. HW-9AF Flexible Head Torch Assemblies
HW-9AF (variable), 12-1/2 ft. 19922
HW-9AF (variable), 25 ft. 19923
5
4 (See Note)
3/8 - 24
3/8 - 24
* Optional PVC Power Cable 57Y01 (12 1/2 ft.); 57Y03 (25 ft.)
SECTION 4
PARTS
14
15
SECTION 4
PARTS
F-14-380-F 7/2000 1M Printed in U.S.A
IF YOU DO NOT KNOW WHOM TO CALL
Telephone: (800) ESAB-123/ Fax: (843) 664-4452/ Web:http://www.esab.com
Hours: 7:30 AM to 5:00 PM EST
A. CUSTOMER SERVICE QUESTIONS:
Order Entry Product Availability Pricing Delivery
Order Changes Saleable Goods Returns Shipping Information
Eastern Distribution Center
Telephone: (800)362-7080 / Fax: (800) 634-7548
Central Distribution Center
Telephone: (800)783-5360 / Fax: (800) 783-5362
Western Distribution Center
Telephone: (800) 235-4012/ Fax: (888) 586-4670
B. ENGINEERING SERVICE: Telephone: (843) 664-4416 / Fax : (800) 446-5693
Welding Equipment Troubleshooting Hours: 7:30 AM to 5:00 PM EST
Warranty Returns Authorized Repair Stations
C. TECHNICAL SERVICE: Telephone: (800) ESAB-123/ Fax: (843) 664-4452
Part Numbers Technical Applications Hours: 8:00 AM to 5:00 PM EST
Performance Features Technical Specifications Equipment Recommendations
D. LITERATURE REQUESTS: Telephone: (843) 664-5562 / Fax: (843) 664-5548
Hours: 7:30 AM to 4:00 PM EST
E. WELDING EQUIPMENT REPAIRS: Telephone: (843) 664-4487 / Fax: (843) 664-5557
Repair Estimates Repair Status Hours: 7:30 AM to 3:30 PM EST
F. WELDING EQUIPMENT TRAINING:
Telephone: (843)664-4428 / Fax: (843) 679-5864
Training School Information and Registrations Hours: 7:30 AM to 4:00 PM EST
G. WELDING PROCESS ASSISTANCE:
Telephone: (800) ESAB-123 / Fax: (843) 664-4454 Hours: 7:30 AM to 4:00 PM EST
H. TECHNICAL ASST. CONSUMABLES:
Telephone : (800) 933-7070 Hours: 7:30 AM to 5:00 PM EST
ESAB Welding & Cutting Products, Florence, SC Welding Equipment
COMMUNICATION GUIDE - CUSTOMER SERVICES
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
ESAB HW-9R Manuel utilisateur
- Catégorie
- Système de soudage
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: ESAB HW-9R User manual
Documents connexes
-
ESAB PT-32 Plasma Arc Cutting Torch Manuel utilisateur
-
-
-
-
-
-
-
-
-