Toro Super Recycler Mower, SR-21P Manuel utilisateur

Operator’s Manual

Manuel de L’Utilisateur

Manual del Operador

FORM NO. 3319–663

SR-21P Super Recycler

SR-21S Super Recycler

SR-21SE Super Recycler

Walk-behind Power Mower

Model No. 20493, 20494, 20495 — 8900001 & Up

SR-21P Super Recycler

SR-21S Super Recycler

SR-21SE Super Recycler

Tondeuse motorisée à guidage arrière

Modèle No. 20493, 20494, 20495 — 8900001 et suivants

SR-21P Super Recycler

SR-21S Super Recycler

SR-21SE Super Recycler

Cortadora de césped motorizada empujada por

el usuario

Modelos N. 20493, 20494, 20495 — 8900001 y siguientes

The engine exhaust from this product

contains chemicals known to the State of

California to cause cancer, birth defects,

or other reproductive harm.

WARNING:

Les gaz d’échappement du moteur de ce

produit contiennent des produits

chimiques reconnus dans l’état de

Californie comme cancérigènes,

responsables de malformations

congénitales, ou comme nocifs à l’égard

des fonctions de la reproduction.

AVERTISSEMENT:

El escape del motor de esta herramienta

contiene productos químicos que según

la información del Estado de California

producen cáncer, defectos congénitos u

otros riesgos reproductivos.

ADVERTENCIA:

EThe Toro Company – 1997

Printed in USA

i

Figures — Figuras

1778



Self-propelled models

Modèle autotracté

Modelo autopropulsado

English

1. Model and serial number decal

Français

1. Décalcomanie de numéros de modèle et de série

Español

1. Calcomanía con los números de modelo y serie

1064



Hand push models

Modèle non tracté

Modelo de empuje manual

English

1. Model and serial number decal

Français

1. Décalcomanie de numéros de modèle et de série

Español

1. Calcomanía con los números de modelo y serie

311





English

1. Right handle knob 2. Left handle knob

Français

1. Bouton de droite 2. Bouton de gauche

Español

1. Perilla derecha de la

manija

2. Perilla izquierda de la

manija

1

2

3

Figures — Figuras

ii

311

1

3

4

5

2

English

1. Cable tie (self-propelled

model only)

2. Cable tie (hand push

model only)

3. Handle latch

4. Handle stud

5. Control cable

Français

1. Attache de câble (modèle

autotracté uniquement)

2. Attache de câble (modèle

non tracté uniquement)

3. Patte de verrouillage

4. Goujon

5. Câble de commande

Español

1. Abrazadera para cables

(modelo autopropulsado

solamente)

2. Abrazadera para cables

(modelo de empuje

manual solamente)

3. Pestillo de la manija

4. Perno

5. Cable de control

m-1690

2

1

English

1. Rope guide 2. Starter rope

Français

1. Guide-câble 2. Câble de démarreur

Español

1. Guía del cable 2. Cable del arrancador

3



1

2

English

1. Wire harness

2. Battery pigtail

3. Battery case

Français

1. Faisceau de câblage

2. Cordon de batterie

3. Boîtier de batterie

Español

1. Arnés de cable

2. Cable de bateriá

3. Caso de bateriá

4 5

6

Figures — Figuras

iii

1626

3

2

1

4

5

English

1. Dipstick

2. ADD mark

3. FULL mark

4. Fuel tank cap

5. Spark plug wire

Français

1. Jauge d’huile

2. Repère ADD (ajouter)

3. Repère FULL (plein)

4. Bouchon du réservoir de

carburant

5. Fil de bougie

Español

1. Varilla de nivel

2. Marca “ADD” (agregar)

3. Marca “FULL” (lleno)

4. Tapa del depósito de

combustible

5. Cable de la bujía

1

2

3

Hand push models

Modèle non tracté

Modelo de empuje manual

English

1. Throttle control

2. Control bar

3. Recoil starter

Français

1. Commande des gaz

2. Barre de commande

3. Démarreur de rappel

Español

1. Acelerador

2. Barra de control

3. Arrancador recuperador

7 8

Figures — Figuras

iv

1802

2

1

3

4

5

Self-propelled models

Modèle autotracté

Modelo autopropulsado

English

1. Throttle control

2. Ground speed control

3. Control bar

4. Recoil starter

5. Key switch (electric start

model)

Français

1. Commande des gaz

2. Vitesse au sol

3. Barre de commande

4. Démarreur de rappel

5. Commutateur a clé de

contact (modèles à

démarreur électrique)

Español

1. Acelerador

2. Del sistema de

autoimpulsión

3. Barra de control

4. Arrancador recuperador

5. Interruptor con llave

(modelo con arranque

elétrico)

1344

1

English

1. Primer

Français

1. Amorceur

Español

1. Cebador

360

1

2

3

English

1. RUN/DRIVE position

2. RUN/SHIFT position

3. STOP position

Français

1. Position

MARCHE/TRACTION

2. Position

MARCHE/EMBRAYAGE

3. Position ARRET

Español

1. Posición

AVANCE/AUTOMATICO

2. Posición

AVANCE/MANUAL

3. Posición PARADA

9

10

11

Figures — Figuras

v

ABDEC

A = 1” (25 mm)

B = 1-1/2” (38 mm)

C = 2” (51 mm)

D = 2-1/2” (64 mm)

E = 3” (76 mm)

788



English

1. Height-of-cut lever

Français

1. Levier de hauteur de coupe

Español

1. Palanca de ajuste de altura de corte

1003

1

2

3

English

1. Air filter

2. Screw

3. Cover

Français

1. Filtre à air

2. Vis

3. Couvercle

Español

1. Filtro de aire

2. Tornillo

3. Cubierta

1782



English

1. Oil fill tube

Français

1. Tube de remplissage d’huile

Español

1. Tubo de llenado del aceite

986



English

1. .030 in. (.76 mm)

Français

1. 0,076 mm

Español

1. 0,076 mm

12

13

14

15

Figures — Figuras

vi

1709





English

1. Cover 2. Screw (2)

Français

1. Capot 2. Vis (2)

Español

1. Tapa 2. Tornillo (2)

1710





3

4

English

1. Cable clamp screw

2. Throttle cable

3. Throttle lever

4. Throttle stop

Français

1. Vis du serre-câble

2. Câble des gaz

3. Manette d’accélérateur

4. Butée d’accélérateur

Español

1. Tornillo de la abrazadera

del cable

2. Cable del acelerador

3. Palanca del regulador

4. Tope del regulador

402



English

1. Control knob

Français

1. Bouton de commande

Español

1. Botón de mando

757

2

1

3

English

1. Bolt and lockwasher

2. Accelerator

3. Blade

Français

1. Boulon et rondelle de

blocage de la lame

2. Accélérateur

3. Lame

Español

1. Perno y arandela de la

cuchilla

2. Acelerador

3. Cuchilla

16

17

18

19

Figures — Figuras

vii

1712

A

B

C

1

2

3

4

English

1. Flat part of blade

2. Sail

3. Wear

4. Slot formed

Français

1. Section plane de la lame

2. Pale

3. Usure

4. Fente formee

Español

1. Parte plana de la cuchilla

2. Aleta

3. Desgaste

4. Ranura formada

153

1

English

1. Sharpen at this angle only

Français

1. Aiguisez à cet angle seulement

Español

1. Afile en este angulo solament

276

1

English

1. Grease fitting

Français

1. Graisseur

Español

1. Engrasador

777

1

2

3

4

5

Self-propelled models

Modèle autotracté

Modelo autopropulsado

English

1. Handle

2. Brake lever

3. 1/8”–3/16”

4. Nut

5. Cable conduit

Français

1. Mancheron

2. Levier de frein

3. 3,2–4,8 mm

4. Ecrou

5. Gaîne du câble

Español

1. Manija

2. Palanca del freno

3. 3,2–4,8 mm

4. Tuerca

5. Conducto del cable

20

21

22

23

Figures — Figuras

viii

251

1

2

3

4

5

Hand push models

Modèle non tracté

Modelo de empuje manual

English

1. Handle

2. Brake lever

3. 1/8”–3/16”

4. Nut

5. Cable conduit

Français

1. Mancheron

2. Levier de frein

3. 3,2–4,8 mm

4. Ecrou

5. Gaîne du câble

Español

1. Manija

2. Palanca del freno

3. 3,2–4,8 mm

4. Tuerca

5. Conducto del cable

7961

English

1. Kickers

Français

1. Plaques de déflection

Español

1. Placas deflectoras

10931

English

1. Right rear wheel

Français

1. Roue arrière droite

Español

1. Rueda trasera derecha

281

1

2

English

1. Belt cover 2. Bolt

Français

1. Garde de la courroie 2. Boulon

Español

1. Tapa de la correa 2. Tornillo

24

25

26

27

Figures — Figuras

ix

1915

2

1

English

1. Discharge tunnel 2. Discharge tunnel plug

Français

1. Conduit de l’éjecteur 2. Obturateur

Español

1. Canal de descarga 2. Tapón del canal de

descarga

2047

English

1. Side discharge chute

Français

1. Ejecteur latéral

Español

1. Canaleta de descarga lateral

28 29

EN–1

Contents

Page

Introduction 1. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Safety 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Safe Operating Practices 2. . . . . . . . . . . . . .

Safety and Instruction Decals 5. . . . . . . . . .

Assembly 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Handle 6. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Starter Rope 6. . . . . . . . . . . . . . . . . . . . . . . .

Battery 6. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Before Starting 6. . . . . . . . . . . . . . . . . . . . . . . . . .

Oil 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Gasoline 7. . . . . . . . . . . . . . . . . . . . . . . . . . .

Recycling Tips 8. . . . . . . . . . . . . . . . . . . . . . . . . .

General Tips 8. . . . . . . . . . . . . . . . . . . . . . . .

Operation 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Controls 9. . . . . . . . . . . . . . . . . . . . . . . . . . .

Starting Engine 9. . . . . . . . . . . . . . . . . . . . . .

Stopping Engine 9. . . . . . . . . . . . . . . . . . . . .

Self-propelled Drive 9. . . . . . . . . . . . . . . . . .

Pulling Mower Rearward 10. . . . . . . . . . . . . .

Adjusting Cutting Height 10. . . . . . . . . . . . . .

Maintenance 11. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Recommended Maintenance Schedule 11. . .

Air Filter 12. . . . . . . . . . . . . . . . . . . . . . . . . . .

Drain Gasoline 12. . . . . . . . . . . . . . . . . . . . . .

Change Engine Oil 12. . . . . . . . . . . . . . . . . . .

Spark Plug 13. . . . . . . . . . . . . . . . . . . . . . . . .

Throttle Cable 13. . . . . . . . . . . . . . . . . . . . . .

Self-propelled Cable 13. . . . . . . . . . . . . . . . .

Blade 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Lubrication 15. . . . . . . . . . . . . . . . . . . . . . . . .

Blade Brake 15. . . . . . . . . . . . . . . . . . . . . . . .

Charging Battery 15. . . . . . . . . . . . . . . . . . . .

Disposing of Battery 16. . . . . . . . . . . . . . . . .

Cleaning 16. . . . . . . . . . . . . . . . . . . . . . . . . . .

Underside of Mower Housing 16. . . . . . . . . .

Storage 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fuel 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Engine 18. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Cleaning 18. . . . . . . . . . . . . . . . . . . . . . . . . . .

General 18. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removing From Storage 18. . . . . . . . . . . . . .

Accessories 18. . . . . . . . . . . . . . . . . . . . . . . . . . . .

The Toro Starting Guarantee 20. . . . . . . . . . . . . . .

Guaranteed To Start Maintenance Record 22. . . . .

Federal and California Emission Control Warranty

Statement 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

The Toro Performance Warranty 26. . . . . . . . . . . .

Introduction

Thank you for purchasing a Toro product.

All of us at Toro want you to be completely satisfied

with your new product, so feel free to contact your

local Authorized Service Dealer for help with service,

genuine Toro parts, or other information you may

require.

Whenever you contact your Authorized Service

Dealer or the factory, always know the model and

serial numbers of your product. These numbers will

help the Service Dealer or Service Representative

provide exact information about your specific

product. You will find the model and serial number

decal located in a unique place on the product

(Fig. 1 & 2).

For your convenience, write the product model and

serial numbers in the space below.

Model No.

Serial No.

Read this manual carefully to learn how to operate

and maintain your product correctly. Reading this

manual will help you and others avoid personal injury

and damage to the product. Although Toro designs,

produces and markets safe, state-of-the-art products,

you are responsible for using the product properly

and safely. You are also responsible for training

persons who you allow to use the product about safe

operation.

EN–2

The Toro warning system in this manual identifies

potential hazards and has special safety messages that

help you and others avoid personal injury, even death.

DANGER, WARNING and CAUTION are signal

words used to identify the level of hazard. However,

regardless of the hazard, be extremely careful.

DANGER signals an extreme hazard that will cause

serious injury or death if the recommended

precautions are not followed.

WARNING signals a hazard that may cause serious

injury or death if the recommended precautions are

not followed.

CAUTION signals a hazard that may cause minor or

moderate injury if the recommended precautions are

not followed.

Two other words are also used to highlight

information. “Important” calls attention to special

mechanical information and “Note” emphasizes

general information worthy of special attention.

Safety

This machine meets or exceeds CPSC blade safety

requirements for walk–behind rotary mowers and

the B71.1 specifications of the American National

Standards Institute, in effect at time of

production. However, improper use or

maintenance by the operator or owner can result

in injury. To reduce the potential for injury,

comply with these safety instructions and always

pay attention to the safety alert

symbol which

means CAUTION, WARNING or

DANGER—“personal safety instruction.” Failure

to comply with the instruction may result in

personal injury.

Safe Operating Practices

This product is capable of amputating hands and feet

and throwing objects. Always follow all safety

instructions to avoid serious injury or death.

POTENTIAL HAZARD

• Engine exhaust contains carbon monoxide,

which is an odorless, deadly poison.

WHAT CAN HAPPEN

• Carbon monoxide can kill you and is also

known to the State of California to cause

birth defects.

HOW TO AVOID THE HAZARD

• Do not run engine indoors or in an enclosed

area.

This mower is designed for cutting and recycling

grass or, when equipped with a grass bag, for

catching cut grass. Any use for purposes other than

these could prove dangerous to user or bystanders.

Note: This engine is NOT equipped with a

spark arrester muffler. Use or operation

of this mower in the State of California

on any forest-covered, brush-covered

or unimproved grass-covered land,

without an approved spark arrester

muffler, is a violation of the law. Other

states may have similar laws.

General Operation

1. Read this manual carefully before operating the

mower. Become familiar with the controls and

proper use of the mower. Never allow children

under 16 years of age to operate the mower.

Never allow adults to operate mower without

proper instructions.

2. The operator of the mower is responsible for

keeping everyone, especially children and pets,

away from area of operation. The operator is

responsible for accidents or hazards occurring to

other people or their property.

3. Thoroughly inspect area where mower will be

used and remove sticks, stones, wire, and debris.

Watch for foreign objects while mowing.

EN–3

4. Wear long pants and substantial shoes. Do not

operate mower while wearing open-toed shoes,

jewelry, loose clothing or when barefoot.

5. Check fuel level before starting engine. Because

fuel is highly flammable, handle it carefully.

A. Use an approved container.

B. Fill fuel tank outdoors, not indoors.

NEVER ADD FUEL TO AN ENGINE

THAT IS RUNNING OR HOT.

C. Install gas cap on fuel container and gas

tank, and wipe up any spilled gasoline

before starting engine.

D. Do not smoke while refueling.

6. Keep all guards, shields, grass catchers and

safety devices in place. Repair or replace

damaged parts, including decals. Check all

safety devices before each use.

7. Before using, always visually inspect to see that

the blades, blade fasteners and cutter assembly

are not worn or damaged. Replace worn or

damaged blades and fasteners in sets to preserve

balance.

8. Traction drive (self-propelled model), blade and

engine are designed to stop when control bar is

released. Ensure control and brake function

properly before each use of mower.

9. Disengage the self-propelled mechanism or drive

clutch (self-propelled model) before starting the

engine.

While Operating

1. Do not run engine indoors.

2. Start the engine carefully according to

instructions and with feet well away from the

blade.

3. Always maintain secure footing. Keep a firm

grip on the handle and walk; never run. Never

operate mower in wet grass. Mow only in

daylight or in good artificial light.

4. Mow across the face of slopes; never up and

down. Use extreme caution when changing

direction on slopes. Do not mow excessively

steep slopes. Wear skid resistant shoes on slopes.

5. Always wear safety glasses or eye shields during

operation to protect eyes from foreign objects

that may be thrown from the machine. Wearing

of hearing protection, protective gloves and a

safety helmet is advisable.

6. Keep face, hands, and feet away from the mower

housing and cutter blade when the engine is

running. Blade can cause injury to hands and

feet. Stay behind the handle until the engine

stops.

7. Use extreme caution when reversing or pulling

the mower towards you.

8. Since the blade rotates for a few seconds after

the control bar is released, stay behind the

handle until the engine stops.

9. When bagging grass, stop engine and stay

behind handle until all moving parts stop before

removing and emptying bag.

10. When mowing, ensure grass bag is installed over

discharge opening.

11. Shut engine off and stay behind handle until all

moving parts stop before unclogging chute.

12. After striking a foreign object or if mower

vibrates abnormally, stop engine and remove

wire from spark plug. Check mower for damage

and make all repairs before using mower again.

If major repairs are ever needed or if assistance

is desired, contact your local Authorized Toro

Service Dealer.

13. Stop the engine and wait for all moving parts to

stop before adjusting the height-of-cut.

14. Stop the blade when pushing the mower outside

the lawn area.

EN–4

15. Stop engine before leaving the operator’s

position – behind the handle. Disconnect wire

from spark plug if mower will be unattended.

16. Do not touch engine while it is running or

shortly after it is stopped because engine will be

hot enough to cause a burn.

17. Refuel only when engine is cool.

18. If mower must be lifted to be transported, turn

off engine and stay behind the handle until all

moving parts stop.

Maintenance

1. Perform only those maintenance instructions

described in this manual. If major repairs are

ever needed or if assistance is desired, contact

your local Authorized Toro Service Dealer.

2. Before mower is cleaned, inspected, serviced, or

adjusted, stop engine and disconnect wire from

spark plug. Keep wire away from plug to prevent

accidental starting.

3. To ensure the mower is in safe operating

condition, frequently check and keep all nuts,

bolts, and screws tight. Ensure blade bolt is

tightened to 40-50 ft.-lbs. (54-68 Nm).

4. When servicing blade, refer to blade

maintenance section for correct installation and

servicing procedures.

5. To reduce fire hazard, keep engine free of

excessive grease, grass, leaves, and

accumulations of dirt.

6. Do not overspeed the engine by changing

governor settings.

7. Check grass catcher bag frequently for wear or

deterioration. Replace with a new bag when

worn or damaged for your protection.

8. Allow engine to cool before storing mower in

any enclosure. Do not store mower near any

open flame or where gasoline fumes may be

ignited by a spark.

9. At the time of manufacture, the mower

conformed to the safety standards in effect for

rotary mowers. To ensure best performance and

continued safety certification of the mower, use

genuine TORO replacement parts and

accessories. Replacement parts and accessories

made by other manufacturers may result in

nonconformance with the safety standards, and

that could be dangerous.

EN–5

Safety and Instruction Decals

Safety decals and instructions are easily visible to the operator and are located near

any area of potential danger. Replace any decal that is damaged or lost.

ON MOWER HOUSING

(Part No. 39-5770)

UNDER COVER-DEFLECTOR

ASSEMBLY ON MOWER DECK

(Part No. 82-8450)

Model 20494

ON CONTROL PANEL

(Part No. 98–1503)

ON MOWER HOUSING

(Part No. 93-0248)

Model 20495

ON CONTROL PANEL

(Part No. 95–3013)

Model 20495

ON BATTERY

(Part No. 92–8659)

EN–6

Assembly

Note: Determine left and right hand sides of

the unit by standing in the normal

operator’s position.

Handle

1. The mower is shipped from the factory with

filler between the upper and lower handle joints

to prevent shipping and assembly damage. Align

upper and lower handles and remove the filler

with a pliers.

2. The left handle knob is shipped from the factory

on the outside of the handle (Fig. 3). Remove the

left knob and bolt. Reinstall knob and bolt on

inside of handle (Fig. 4). Both handle knobs

should be positioned on the inside of the

handles. Tighten handle knobs.

3. Move handle latches slightly outward so they

will not be in the way when pivoting the handle

backward into the operating position (Fig. 4).

4. Pivot handle backward. Move handle latches

inward while snapping handle stud into center

hole of handle latch (Fig. 4). If a handle latch

does not fit tightly against the handle tube,

remove latch from handle stud, bend the latch

inward, and reattach to handle stud. Repeat as

necessary to ensure a tight fit between latch and

handle. Make sure handle knobs are securely

tightened.

Note: If handle height is not satisfactory,

adjust by placing handle stud into a

different hole.

5. Ensure control cables are to the rear and inside

of handles. Secure cables to handle with cable

ties (Fig. 4).

Starter Rope

1. Pull starter rope through rope guide on handle

(Fig. 5).

Note: To make the rope easier to loop,

squeeze the control bar on the handle

to release the blade brake.

Battery

(Electric start models only)

1. Connect battery to wire harness (Fig. 6).

2. Charge Battery. Refer to Charging Battery

section.

Before Starting

Oil

Fill crankcase with SAE 30 oil until oil level reaches

FULL mark on dipstick. 10W-30 oil may be

substituted if SAE 30 is not available. The maximum

crankcase capacity is 20 ounces (0.6 liters) of oil.

Use any high quality detergent oil having the

American Petroleum Institute (API) “service

classification”—SF, SG, SH or SJ.

Before each use, ensure oil level is between FULL

and ADD marks on dipstick (Fig. 7). Add oil if level

is low.

1. Position mower on level surface and clean

around oil dipstick (Fig. 7).

2. Remove dipstick by rotating cap

counterclockwise 1/4 turn.

3. Wipe dipstick and insert it into filler neck.

Rotate cap clockwise 1/4 turn. Then remove

dipstick and check level of oil on side of dipstick

with FULL and ADD marks (Fig. 7). If level is

low, add only enough oil to raise level to FULL

mark on dipstick. DO NOT FILL ABOVE

FULL MARK BECAUSE ENGINE COULD

BE DAMAGED WHEN STARTED. POUR

OIL SLOWLY.

EN–7

4. Insert dipstick into filler neck and rotate cap

clockwise 1/4 turn to lock.

Note: Check oil level each time mower is

used or after every 5 operating hours.

Initially, change oil after the first 5

hours of operation; thereafter, change

oil after every 50 hours of operation.

More frequent oil changes are required

in dusty or dirty conditions.

Gasoline

POTENTIAL HAZARD

• In certain conditions gasoline is extremely

flammable and highly explosive.

WHAT CAN HAPPEN

• A fire or explosion from gasoline can burn

you, others, and cause property damage.

HOW TO AVOID THE HAZARD

• Use a funnel and fill the fuel tank outdoors,

in an open area, when the engine is cold.

Wipe up any gasoline that spills.

• Do not fill the fuel tank completely full.

Add gasoline to the fuel tank until the level

is 1/4” to 1/2” (6 mm to 13 mm) below the

bottom of the filler neck. This empty space

in the tank allows gasoline to expand.

• Never smoke when handling gasoline, and

stay away from an open flame or where

gasoline fumes may be ignited by a spark.

• Store gasoline in an approved container

and keep it out of the reach of children.

• Never buy more than a 30-day supply of

gasoline.

Note: Do not use gasoline that has been

stored in an approved container from

one season to the next. Toro strongly

recommends the use of fresh, clean,

UNLEADED

regular grade gasoline in

Toro gasoline powered products.

Unleaded gasoline burns cleaner,

extends engine life, and promotes good

starting by reducing the build-up of

combustion chamber deposits. Leaded

gasoline can be used if unleaded is not

available.

Toro also recommends that Toro

Stabilizer/Conditioner be used regularly in all Toro

gasoline powered products during operation and

storage seasons. Toro Stabilizer/Conditioner cleans

the engine during operation and prevents gum-like

varnish deposits from forming in the engine during

periods of storage.

IMPORTANT: Do not mix oil with the

gasoline. Never use methanol

, gasoline

containing methanol, gasohol containing

more than 10% ethanol or white gas because

engine fuel system damage could result.

Do not use fuel additives other than those

manufactured for fuel stabilization during

storage such as Toro’s Stabilizer/conditioner

or a similar product. Toro’s

Stabilizer/conditioner is a petroleum distillate

based conditioner/stabilizer. Toro does not

recommend stabilizers with an alcohol base

such as ethanol, methanol or isopropyl.

Additives should not be used to try to

enhance the power or performance of

machine.

1. Clean around fuel tank cap and remove cap from

tank (Fig. 7).

2. Using unleaded gasoline, fill fuel tank to within

1/4” to 1/2” (6 to 13 mm) from top of tank, not

into filler neck. Do not fill tank full.

3. Reinstall fuel tank cap and wipe up any spilled

gasoline.

4. Connect spark plug wire (if disconnected)

(Fig. 7).

EN–8

Recycling Tips

General Tips

Follow these instructions whether cutting grass or

leaves for the best cutting results and lawn

appearance:

• Maintain a sharp blade

throughout the cutting

season. Periodically file down nicks on blade.

• Only mow dry grass or leaves. Wet grass and

leaves tend to clump on yard and may cause

mower to plug or engine to stall. They may also

be slippery to walk on and could cause you to

slip and fall.

POTENTIAL HAZARD

• Wet grass or leaves can cause you to slip

and contact blade.

WHAT CAN HAPPEN

• Blade contact can seriously injure you.

HOW TO AVOID THE HAZARD

• Mow only in dry conditions.

• Set engine speed to fastest position. Maximum

horsepower provides best cutting results.

• Clean clippings or leaves from underside of

mower deck after each mowing.

• Keep engine in good running condition. Cutting

and recutting requires more horsepower.

• Clean air filter more frequently. Cutting and

recutting stirs up more clippings and dust which

clogs the air filter and reduces engine

performance.

Cutting Grass

• Grass grows at different rates at different times

of the year. In the heat of summer, it is generally

best to cut grass at the C, D or E height-of-cut

settings. Only about !/3 of the grass blade should

be cut off. Cutting below the C inch setting is

not recommended unless grass is sparse or it is

late fall when grass growth begins to slow down.

• When changing height-of-cut from the

established setting (ex. C, D or E) to a new

height, the grass may appear ragged or uneven

until the grass adjusts to the new established

height-of-cut and regains its normal appearance.

• When cutting grass over six inches tall, you may

want to first mow using the highest height-of-cut

setting and a slower walking speed; then mow

again at a lower setting for best lawn appearance.

If grass is too long and leaves clumps on top of

lawn, mower may plug and cause engine to stall.

• Alternate mowing direction. This helps disperse

clippings over lawn for even fertilization.

If the finished cut lawn appearance is unsatisfactory,

try one or more of the following:

• Sharpen the blade.

• Walk at a slower pace while mowing.

• Raise the height-of-cut setting on your mower.

• Cut grass more frequently.

• Overlap cutting swaths instead of cutting a full

swath with each pass.

• Set height-of-cut on front wheels one notch

lower than rear wheels. (example: set front

wheels at “C” setting and rear wheels at “D”

setting)

Cutting Leaves

• When cutting is complete, always be sure that

50% of the lawn shows through the cut leaf

cover. This may require one or more passes over

the leaves.

EN–9

• For light leaf coverage, position all wheels at the

same height-of-cut setting.

• If there are more than five inches of leaves on

lawn, set the front wheels one or two notches

higher than the rear wheels. This makes it easier

to feed leaves under mower deck.

• Walk at a slower mowing speed if leaves are not

being cut up finely enough to be hidden down in

the grass.

• If you cut up a lot of oak leaves, you might want

to add lime to your grass in the spring. Lime

reduces the acidity of oak leaves.

Operation

Controls

Key switch (electric start model), throttle control,

ground speed control (self-propelled model), control

bar and recoil starter are on upper handle

(Fig. 8 & 9).

Starting Engine

1. Push spark plug wire onto spark plug (Fig. 7).

2. Self-propelled model only–Move ground speed

control to N (NEUTRAL).

3. Move throttle control to

(FAST).

4. Push primer three (3) times (Fig. 10). Wait

about two (2) seconds between each push.

Note: Do not use primer to restart a warm

engine after a short shutdown.

However, cool weather may require

priming to be repeated.

5. Start the mower:

• Manual Starting: Squeeze control bar

against handle. Pull starter handle lightly

until resistance is felt, then pull sharply. Let

rope return to handle slowly.

• Key-lectric Starting (Electric start

models only): Insert key into switch.

Squeeze control bar against handle. Turn

key to START and release when engine

begins running.

Note: If the battery’s charge is too weak to

start the engine, the engine can be

started with the recoil starter.

6. Regulate throttle as desired between

(FAST)

and (SLOW).

Stopping Engine

1. Release control bar. Engine, blade and traction

drive will stop. See your dealer immediately if

they do not. Stay behind the handle until all

moving parts stop.

2. Pull wire off spark plug if mower will be

unattended or not used. Remove key from switch

on electric start model.

Self-propelled Drive

(Self-propelled models only)

The mower has three ground speeds: number “1” is

slow, “2” is medium, and “3” is a fast walking pace.

1. Move control bar to the RUN/SHIFT position

(Fig. 11).

2. Move ground speed control to desired setting.

3. To engage the self-propel drive, squeeze the

control bar against the handle to the

RUN/DRIVE position (Fig. 11).

Note: Do not shift speeds while control bar is

squeezed against handle in the

RUN/DRIVE position (Fig. 11); the

transmission could be damaged. Move

control bar to the RUN/SHIFT position

when changing ground speed.

La page charge ...

Toro Super Recycler Mower, SR-21P Manuel utilisateur

Toro Super Recycler Mower, SR-21P Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents