Citizen CT-S2000DC Le manuel du propriétaire

LINE THERMAL PRINTER

MODEL CT-S2000/CT-S2000DC

User’s Manual

Mode d’emploi

Benutzerhandbuch

Manuale dell’utente

Manual de Usuario

IMPORTANT: This equipment generates, uses, and can radiate radio frequency energy

and if not installed and used in accordance with the instruction manual, may cause

interference to radio communications. It has been tested and found to comply with

the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC

Rules, which are designed to provide reasonable protection against such interference

when operated in a commercial environment. Operation of this equipment in a

residential area is likely to cause interference, in which case the user at his own

expense will be required to take whatever measures may be necessary to correct

the interference.

CAUTION: Use shielded cable for this equipment.

Sicherheitshinweis

Die Steckdose zum Anschluß dieses Druckers muß nahe dem Gerät angebracht und

leicht zugänglich sein.

For Uses in Canada

This Class A digital apparatus complies with Canadian ICES-003.

This digital apparatus does not exceed the class A limits for radio noise emissions

from digital apparatus, as set out in the radio interference regulations of the Canadian

department of communications.

Pour L’utilisateurs Canadiens

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Cet appareil numérique ne dépasse pas les limites de carégorie a pour les émissions

de bruit radio émanant d’appareils numériques, tel que prévu dans les réglements

sur l’interférence radio du départment Canadien des communications.

This printer conforms to the following Standards:

Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336/EEC,

92/31/EEC, 93/68/EEC.

LVD:EN60950-1

EMC : EN55022 Class A

EN61000-3-2

EN61000-3-3

EN55024

This declaration is applied only for 230V model.

Declaration of Conformity

ENGLISH

— 1 —

GENERAL PRECAUTIONS

● Before using this product, be sure to read through this manual. After having read

this manual, keep it in a safe, readily accessible place for future reference.

● The information contained herein is subject to change without prior notice.

● Reproduction or transfer of part or all of this document in any means is prohibited

without permission from Citizen Systems.

● Note that Citizen Systems is not responsible for any operation results regardless

of missing, error, or misprinting in this manual.

● Note that Citizen Systems is not responsible for any trouble caused as a result of

using options or consumables that are not specified in this manual.

● Except explained elsewhere in this manual, do not attempt to service, disassemble,

or repair this product.

● Note that Citizen Systems is not responsible for any damage attributable to

incorrect operation/handling or improper operating environments that are not

specified in this manual.

● Data is basically for temporary use and not stored for an extended period of time

or permanently. Please note that Citizen Systems is not responsible for damage

or lost profit resulting from the loss of data caused by accidents, repairs, tests or

other occurrence.

● If you find loss of information, error, or uncertain matter, please contact your

Citizen Systems dealer.

● If you find any disordered or missing page(s), contact your Citizen Systems dealer

for replacement.

THE TABLE OF CONTENTS

1. GENERAL OUTLINE .................................................................... 7

2. EXPLANATION OF PRINTER PARTS........................................ 10

3. PREPARATION ........................................................................... 12

4. MAINTENANCE AND TROUBLESHOOTING ........................... 17

5. OTHER ....................................................................................... 22

CITIZEN is a registered trade mark of Citizen Holdings Co., Japan

CITIZEN es una marca registrada de Citizen Holdings Co., Japón

Company names and product names in this manual are trademarks or

registered trademarks of relevant companies.

Copyright c 2008 by CITIZEN SYSTEMS JAPAN CO., LTD.

— 2 —

SAFETY PRECAUTIONS ... WHICH SHOULD BE STRICTLY OBSERVED

Before using this product for the first time, carefully read these SAFETY PRECAUTIONS. Improper

handling may result in accidents (fire, electric shock or injury).

In order to prevent injury to operators, third parties, or damage to property, special warning symbols

are used in the User’s Manual to indicate important items to be strictly observed.

● After having read this Manual,

keep it in a safe, readily accessible place for future reference.

● Some of the descriptions contained in this manual may not be relevant to some printer models.

The following describes the degree of hazard and damage that could occur if the printer is improperly

operated by ignoring the instructions indicated by the warning symbols.

This symbol is used to alert your attention to important items.

WARNING

Neglecting precautions indicated by this symbol may result in injury or damage to properties.

CAUTION

This symbol is used to alert you to the danger of electric shock or electrostatic damage.

This symbol denotes a request to unplug the printer from the wall outlet.

This symbol is used to indicate useful information, such as procedures, instructions or the

like.

This symbol is used to indicate prohibited actions.

Neglecting precautions indicated by this symbol may result in fatal or serious injury.

— 3 —

■ Do not use or store this product in a place where it will be exposed to:

* Flames or moist air.

* Direct sunlight.

* Hot airflow or radiation from a heating device.

* Salty air or corrosive gases.

* Ill-ventilated atmosphere.

* Chemical reactions in a laboratory.

* Airborne oil, steel particles, or dust.

* Static electricity or strong magnetic field.

• Neglecting these warnings may result in printer failure, overheating, emission of

smoke, fire, or electric shock.

■ Do not drop any foreign object nor spill liquid into the printer. Do not place any

object on the printer either.

■ Do not drop any metallic object such as paper clip, pin or screw into the printer.

■ Do not place a flower vase, pot or cup containing water on the printer.

■ Do not spill coffee, soft drinks or any other liquid into the printer.

■ Do not spray insecticide or any other chemical liquid over the printer.

•A metallic foreign object, if accidentally dropped into the printer, may cause printer

failure, fire, or electric shock. Should it occur, immediately turn the printer off,

unplug it from the supply outlet, and call your local Citizen Systems dealer.

Do not handle the printer in the following ways:

■ Do not allow the printer to sustain strong impacts or hard jolts (e.g., trampling,

dropping, striking with a hard edge).

■ Never attempt to disassemble or modify the printer.

• Neglecting to handle properly may result in printer failure, overheating, emission

of smoke, fire, or electric shock.

■ Install, use, or store the printer out of the reach of children.

• Electric appliances could cause an unexpected injury or accident if they are handled

or used improperly.

•Keep the power cord and signal cables out of the reach of children. Also children

should not be allowed to gain access to any internal part of the printer.

• The plastic bag the printer came in must be disposed of properly or kept away

from children. Wearing it over the head may lead to suffocation.

WARNING

— 4 —

Please observe the following precautions for power source and power cord:

■ Do not plug or unplug the power cord with a wet hand.

■ Use the printer only at the specified supply voltage and frequency.

■ Use only the specified AC adapter with the printer.

■ Check to make sure that the supply outlet from which the printer is powered has a

sufficient capacity.

■ Do not supply the printer from a power strip or current tap shared with other

appliances.

■ Do not plug the power cord into a supply outlet with dust or debris left on its plug.

■ Do not use a deformed or damaged power cord.

■ Do not move the printer while the printer power is on.

• Neglecting to handle properly may result in printer failure, emission of smoke, fire,

or electric shock.

• An overload may cause the power cord to overheat or fire or the circuit breaker to

trip.

■ Do not allow anything to rest on the power cord. Do not place the printer where

the power cord will be trampled on.

■ Do not use or carry the printer with its power cord bent, twisted, or pulled.

■ Do not attempt to modify the power cord unnecessarily.

■ Do not lay the power cord in the neighbor of a heating device.

• Neglecting these cautions may cause wires or insulation to break, which could

result in leakage, electric shock, or printer failure. If the power cord sustains

damage, contact your Citizen Systems dealer.

■ Do not leave things around the supply outlet.

■ Supply power to the printer from a convenient wall outlet, readily accessible in an

emergency.

• The printer may not be immediately shut down in an emergency.

■ Insert the power plug fully into the outlet.

■ If the printer will not be used for a long time, leave it disconnected from its supply

outlet.

■ Hold the plug and connector when plugging or unplugging the power cord or signal

cable after turning off the printer and the appliance connected to it.

WARNING

— 5 —

Do not use the printer under the following conditions.

■ A state subject to vibration or unstable state.

■ A state with this product slanted.

• Otherwise dropping may cause injury.

• Poor print quality may occur.

■ A state where the printer ventilation holes are obstructed by a nearby wall or other

equipment.

■ A state where any object is placed on the printer

■ A state where the printer is covered or wrapped by a cloth or bed clothing

• Be careful about internal heat buildup, which could cause fire and deform the case.

■ Avoid using the printer near a radio or TV set or from supplying it from the same

outlet as these appliances.

■ Avoid using the printer interconnected with a cable or cord that has no protection

against noise. (For interconnections, use shielded or a twisted pair of cables and

ferrite cores, or other anti-noise devices.)

■ Avoid using the printer with a device that is a strong source of noise.

• The printer may have an adverse effect on nearby radio or TV transmissions. There

may also be cases when nearby electrical appliances adversely influence the printer,

causing data errors or malfunction.

■ A state where this product is installed vertically or sidelong.

• Malfunction, failure, or electric shock may result.

■ Use the printer with its grounding post connected to a convenient grounding facility.

• If leakage occurs electric shock may result.

■ Do not connect the printer’s grounding post onto any of the following facilities:

* Utility gas piping

• A gas explosion could result.

* Telephone line ground

* Lightning rod

• If lightning strikes a large surge of current may cause fire or shock.

* Utility water pipes

• Plastic water pipes should not be used for grounding. (Those approved by

a Waterworks Department may be used.)

■ Before connecting or disconnecting the grounding lead to or from the printer, always

unplug it from supply outlet.

CAUTION

Caution label is attached on the

position shown in the following figure.

Carefully read the precautions in

handling before using the printer.

THIS LABEL INDICATES THE

RISK OF ANY INJURY DUE TO

“HIGH TEMPERATURE” OF

THE PRINT HEAD.

— 6 —

To prevent possible malfunction or failure observe the following.

■ Avoid operating the printer without paper properly loaded.

■ Avoid the use of paper not complying with specifications.

•May result in poor print quality.

■ Avoid using torn pieces of paper or spliced with plastic adhesive tapes.

■ Avoid forcibly pulling already loaded paper by hand.

■ Avoid wedging the paper into the printer.

•May jam paper. To release, refer to “Removing Jammed Paper” in this manual.

■ Avoid using a sharp pointed device to operate panel keys.

■ Be sure to firmly insert the cable plug into its mating socket.

•A cross connection may damage the printer’s internal electronics or the host

system’s hardware.

■ Only use the printer with devices that have designated solenoid specifications for

the cash drawer interface connector.

• Neglecting this caution may result in malfunction or failure.

■ Do not transport this printer with the paper roll inside.

•Printer failure or breakage may occur.

CAUTION

To prevent injury and printer failures from worsening, observe the following:

■ Do not touch the printing surface of the thermal head.

■ Do not touch any of the moving parts (e.g., paper cutter, gears, active electrical

parts) while the printer is working.

■ In case of trouble do not attempt to repair the printer. Ask Citizen Systems

service for repair.

■ Be careful that the printer cover does not entrap your hands or fingers.

■ Be careful with sharp edges on the printer. Do not allow them to injure you or

damage property.

•May result in electric shock, burn, or injury.

If the printer emits smoke, an odd smell, or unusual noise while printing, immediately

abort the current print session and unplug the printer from the supply outlet.

Observe the following precautions for daily maintenance.

■ When cleaning the printer, always turn it off and unplug it from the supply outlet.

■ Use a soft, dry cloth for cleaning the surface of the printer case.

■ For severe stains, use a soft cloth slightly dampened with water.

■ Never use organic cleaning solvent such as alcohol, paint thinner, trichloroethylene,

benzene, or ketone. Never use a chemically processed cleaning cloth.

■ To remove paper dust, use a soft brush.

DAILY MAINTENANCE

CAUTION

• The thermal head is at a dangerously high temperature immediately after printing.

Allow it to cool off before launching maintenance work.

— 7 —

1. GENERAL OUTLINE

The CT-S2000/CT-S2000DC are thermal line printers designed for use with a broad array

of terminal equipment including data, POS, and kitchen terminals.

With extensive features, they can be used in a wide range of applications.

1.1 Features

● Compact, easy-to-use universal design.

● Drop-in Paper Roll mechanism facilitating easy paper handling and head cleaning.

● Drip-proof design

● High speed (220 mm/s) printing.

● Versatile Roll Capacity with ability to use 83 mm, 80 mm, 60 mm and 58 mm wide

paper rolls.

● Can use paper roll with a maximum of 102 mm diameter.

● Equipped with USB interface as standard

● Replaceable interface board.

● High-speed parallel interface (Parallel interface model)

● Built-in cash drawer interface.

● Auto cutter mechanism provided as a standard.

● User customization such as memory switch setting are available.

● Page mode. Now you can arrange pages freely.

● Registration of user-defined characters and logos into flash memory.

● Barcode & 2D Barcode printing is supported.

● 2-color printing is supported(When specified paper is used).

● Error indication is available with LED or buzzer.

— 8 —

CT-S2000

(AC power type)

Sample paper roll

User’s manual

(This manual)

AC power cord

1.3 Model Classification

The printer models are classified by the following designation method:

CT-S2000DC

(DC power supply type)

AC adapter

(Option)

CT - S2000 RS E - BK -

Label/Black mark

No marking: Standard

L: Label

M: Black mark

Body case color

WH: Cool white

BK: Black

GR: Dark Grey

Interface

PA: IEEE1284 & USB

RS: RS-232C & USB

UB: USB only (Option)

Power supply

No marking: AC power type

(built-in power supply)

DC: DC power supply type

Character set, AC cable,

E: Europe

U: USA

Sample paper roll

User’s manual

(This manual)

AC power cord

(Option)

1.2 Unpacking

When unpacking the printer, confirm that the following are provided:

● Printer: 1

● AC adapter (Option, only for CT-S2000DC): 1

● AC power cord (Option, only for CT-S2000DC): 1

● Sample paper roll: 1 roll

● User’s manual (This manual): 1

— 9 —

1.4 Basic Specifications

Item Specifications

Model CT-S2000 PA, CT-S2000 RS, CT-S2000DC PA, CT-S2000DC RS

Print method Line thermal dot print method

Print width

*1 80 mm/640 dots, 72 mm/576 dots, 54.5 mm/436 dots,

54 mm/432 dots

Dot density 8 × 8 dots/mm (203 dpi)

Print speed 220 mm/s (Fastest, print density 100 %), 1760 dot lines/s

Number of print

columns

*2

Character size *4 Font A: 1.50 × 3.00 mm, Font B: 1.13 × 3.00 mm, Font C: 1.00 × 2.00 mm

Character type Alphanumeric, International, PC437 PC850/852/857/858/860/863/864/

865/866/WPC1252/Katakana/Thai code 18

User memory

384 KB (Capable of registering user-defined characters and logos)

Types of bar code UPC-A/E, JAN (EAN) 13/8 columns, ITF, CODE 39, CODE 128, CODABAR,

CODE 93, PDF417, QR Code

Line spacing 4.23 mm (1/6 inch)

Paper roll

Thermal paper roll: 83 mm/80 mm/60 mm/58 mm ×Maximum φ102 mm

Paper thickness: 65-85 µm

Interfacing Serial (RS-232C compliant), Parallel (IEEE 1284 compliant), USB

Cash drawer interface 2 cash drawers are supported.

Input buffer 4k bytes/45 bytes

Supply voltage DC 24 V ±7%

Power consumption Approx. 70W (in normal printing)

AC adapter Rated input: AC 100 to 240 V, 50/60 Hz, 150 VA

Rated output: DC 24 V, 2A

Model 35AD1 for CT-S2000 / Model 35AD2 for CT-S2000DC

Weight CT-S2000:Approx. 2 kg, CT-S2000DC:Approx. 1.8 kg

Outside dimensions 147 (W) × 207 (D) × 147 (H) mm

Operating temperature 5 to 45°C, 10 to 90% RH (No condensation)

and humidity

Storage temperature −20 to 60°C, 10 to 90% RH (No condensation)

and humidity

Reliability Print head life: 150 km, 2 × 10

8

pulses (At normal temperature/

humidity with recommended paper used)

Auto cutter life:2 million cuts (At normal temperature/

humidity with recommended paper used)

Safety standard

*3 UL, C-UL, FCC Class A, TÜV-GS, CE Marking

83mm 80mm 60mm 58mm

Font A 53 48 36 35 12 × 24

Font B 71 64 48 46 9 × 24

Font C 80 72 54 52 8 × 16

Number of print columns

(columns)

Dot configuration

(Dot)

Paper width

Font

Notes:

*1: When paper width is 83, 80, 60, 58 mm

*2: The number of printable columns is selectable with a Memory Switch.

The number of columns in this table refers to typical model. Printer varies partly in the number of

columns depending on printer specifications.

*3: This rating is obtained by the use of specified AC adapter (35AD1 or 35AD2).

*4: As each character size includes the space inside the character font, actual character looks smaller.

+0

−1

+0

−1

+0

−1

+0

−1

— 10 —

2.

EXPLANATION OF PRINTER PARTS

2.1 Printer Appearance

● Printer cover

Paper is loaded under this cover.

● Cover open button

To refill or replace paper, open the printer cover by lifting the cover open button.

● Power switch

This switch turns the printer power ON/OFF.

POWER LED

FEED button

ERROR LED

Operation Panel

● POWER LED

Illuminated when the printer power is on and off when the printer power is off. May

blink or light in a special mode or in case of failure.

● ERROR LED

Illuminated or blinks when paper is empty or in case of failure.

The interval length of blinking represents the type of error.

● FEED button

Pressing this button once causes the paper to feed one line. The longer the button is

pressed, the more paper is fed.

In case of auto cutter error, press the FEED button after removing the cause of the

error.

See 4.6 Error Indication

Power switch

Operation panel

Rear connector

(Front view) (Rear view)

Printer cover

Cover open button

— 11 —

2.2 Printer Cover Inside

● Paper feed roller

Feeds paper as part of print mechanism.

● Paper-near-end sensor

Detects near paper end, change position in

accordance with the outer diameter of paper

core.

● Auto cutter

Cuts the paper with a command at the end

of printing. Cutting method is selectable

between partial cut and full cut with a

command.

● Print (thermal) head

Prints characters and/or graphic data on

thermal paper.

● Paper-end sensor

Stops printing when this sensor detects

paper end.

Print (thermal) head

Paper-end sensor

Paper-near-end

sensor

Auto cutter

Paper feed roller

● Interface connector (Serial, parallel, etc.)

Connects to the interface cable. A DIP switch is provided on the serial interface board.

● Cash drawer kick-out connector

Connects to the cable from the cash drawer.

● AC inlet (AC power type)

Connects to AC power cord

● Power connector (DC power supply type)

Connects to the cable from AC adapter.

Interface connector

(Serial, parallel, etc.)

Cash drawer

kick-out connector

Power connector

(DC power supply type)

Rear Connectors

Interface board

mounting screws

AC inlet

(AC power type)

USB connector

— 12 —

3. PREPARATION

3.1 Connecting the AC Power Cord

1. Tu rn off the printer power.

2. ● For AC power type (with built-in power supply), connect the AC power

cord to the AC inlet at the back of the printer and plug the AC power cord

into the wall outlet.

● For DC power type, connect the AC adapter cable connector to the power

connector at the back of the printer with its flat surface facing interface

connector side. Then connect the AC power cord to the AC inlet of the AC

adapter and then plug the AC power cord to the wall outlet.

CAUTION!

■ Use only the specified AC adapter with the printer.

■ When disconnecting a cable, DO NOT pull out by the cable. Always hold the plug.

■ Always keep the AC power supply away from other noise generating equipment.

■ DO NOT pull the AC power cord. Otherwise fire, electric shock, or power disconnection

may result.

■ If lightning is approaching, unplug the AC power cord from the wall outlet. Otherwise

fire or electric shock may result.

■ Keep the power cord away from heat generating appliances. Otherwise the shield of

power cord may be fused resulting in a fire or electric shock.

■ If the printer will not be used for a long time, leave it disconnected from its supply

outlet.

■ Avoid locating the AC power cord in places which may cause tripping or falling.

AC inlet

AC power cord

AC power type

(built-in power supply)

DC power supply type

AC power cord

AC inlet

Cable connector

Power connector

AC adapter

Flat side

— 13 —

3.2 Connecting Interface Cables

Confirm that the power switch is OFF and connect the interface cable.

Orient the interface cable terminal correctly and insert it into the interface connector.

Printer

Pin Signal

2 TXD

3 RXD

4RTS

6 DSR

7SG

20 DTR

PC

Signal Pin

FG 1

TXD 2

RXD 3

CTS 5

DSR 6

SG 7

DTR 20

CAUTION!

■ When disconnecting the cable, always hold the connector.

■ Be careful not to insert the USB interface cable into the cash drawer kick-out connector.

Serial Interface Parallel Interface

For serial interface cable, use the one with the following connection.

Printer

Pin Signal

1FG

2 TXD

3 RXD

4RTS

6 DSR

7SG

20 DTR

PC

Signal Pin

RXD 2

TXD 3

DTR 4

SG 5

DSR 6

CTS 8

USB Interface

CAUTION!

Avoid locating the interface cable in places which may cause tripping or falling.

25-pin - 25-pin cable 9-pin - 25-pin cable

Cash drawer

kick-out connector

Cash drawer cable

connector

3.3 Connecting the Cash Drawer

1. Confirm that the power switch is OFF.

2. Confirm the top and bottom of the cash drawer

cable connector and insert it into the cash

drawer kick-out connector at the back of the

printer.

3 Screw the cash drawer's ground wire to the body

of the printer.

CAUTION!

DO NOT connect any other device than the specified cash drawer to the cash drawer

kick-out connector. (DO NOT connect a telephone line either.)

— 14 —

(1) Connector Pin Configuration

No. Signal Function

1FG Frame Ground

2 DRAWER 1 Drawer 1 drive signal

3 DRSW Drawer switch input

4 VDR Drawer drive power supply

5 DRAWER 2 Drawer 2 drive signal

6 GND Common ground on circuits

61

Connector used:

TM5RJ3-66 (Hirose)

or equivalent

Applicable connector:

TM3P-66P (Hirose) or

equivalent

VDR

1

2

3

4

5

6

VDR

5V

CAUTION!

■ No output is produced while printing.

■ The cash drawers 1 and 2 cannot be driven simultaneously.

■ A solenoid used for the cash drawer should be of 24 Ω or more. The output current

should be kept at 1A or less; otherwise, breakdown or burning could occur.

CAUTION!

DO NOT use the printer under the following conditions.

■ A state subject to vibration or unstable state.

■ A state with this product slanted.

• Otherwise dropping may cause injury.

• Poor print quality may occur.

■ A state where this product is installed vertically or sidelong.

• Malfunction, failure, or electric shock may result.

Horizontal position

Vertical position

(2) Electrical characteristics

1) Driving voltage: 24 VDC

2) Driving current: Approx. 1A max. (shall not exceed 510

ms.)

3) DRSW signal: Signal levels: “L” = 0 to 0.5 V, “H” = 3 to 5 V

(3) DRSW signal

DRSW signal status can be tested with the DLE+EOT,

GS+a, or GS+r command or

at pin 34 on the parallel interface port.

(4) Drive Circuit (printer side)

3.4 Precautions in Installing the Printer

The printer must only be operated horizontally. Do not operate vertically or install on a

wall.

— 15 —

InitialSettings

1

Communication condition

DIP switch setting Memory switch OFF

setting method

setting

2 Hand shake XON/XOFF DTR/DSR OFF

3 Bit length 7 bits 8 bits OFF

4 Parity check With parity None OFF

5 Parity selection Even parity Odd parity OFF

6 ON

7 ON

8 INIT Reset Invalid OFF

3.6 Setting DIP Switch

CAUTION!

When setting the partition to the slot for 58 mm or 60 mm paper roll, be sure not to set

it slanted.

DIP switch

Interface board

mounting screws

CAUTION!

When setting the DIP switch, DO NOT remove screws other than those for mounting

the serial interface board.

The DIP switch is present on the serial interface

board.

Remove the board fixing screws, take out the

interface board, and then set the DIP switch. The

function of each switch is as shown below.

3.5 Partition for Paper Roll

Selecting baud rate

Switch No.

67

2400 OFF OFF

4800 ON OFF

9600 OFF ON

19200 ON ON

1200, 38400, 57600 and 115200 bps can also be selected by a command, etc.

Switch No. Function ON OFF

Baud rate selection See Table below.

Baud Rate (bps)

Partition

At the time of shipment, this partition is set to “80-mm

wide roll paper position”.

1. Confirm that the power switch is OFF.

2. Open the printer cover.

3. Set the partition to each to the slot which

meets the width of the paper roll used. When

using the 83-mm wide paper roll, remove the

partition.

4. Change the setting of paper width by reffering

to the section 5.2, "Manual Setting of Memory

Switch".

— 16 —

3.7 Adjusting the Paper Near-end Sensor

1. Lightly push in the paper near-end sensor unit.

2. Move the paper near-end sensor unit to the right and left while keeping to

press it. The sensor position is as shown below depending on the diameter

of the roll paper used.

Sensor Position

*1 φ22 φ18

2 φ25 φ22

3 φ29 φ25

4 φ34 φ32

* Factory setting

CAUTION!

■ Paper remaining differs by the type of paper roll used.

■ The external diameter of the paper roll is only for reference.

■ When a paper end error is detected incorrectly during using a paper roll with a honey-

comb type core, move the sensor position to the larger number.

Roll paper diameter at the

detection of near-end

Outer core diameter of

roll paper used

Paper-near-end

sensor unit

— 17 —

CAUTION!

■ Always use the specified types of paper roll.

■ Confirm that the paper roll is set correctly.

■ When the paper is skewed and not extended straightforward from under the printer

cover, open the printer cover and adjust the paper correctly.

■ When the cover is opened after paper setting, be sure to pull the paper straightforward

by several cm out of the printer, and then close the cover.

■ When closing the printer cover, press on the center part of the cover to close it firmly.

■ When setting paper, be careful not to have your finger injured by the paper edge.

4.

MAINTENANCE AND TROUBLESHOOTING

4.1 Setting/Replacing the paper roll

1. Lift the cover open button.

2. Open the printer cover.

3. Insert a paper roll with its print area facing down as shown in the figure and

pull out the paper end straightforward by several cm out of the printer.

4. Firmly close the printer cover until a click can be heard. With the factory

setting, the paper is fed and cut automatically.

See 5.3 Manual Setting of Memory Switch

WARNING

When opening the printer cover, DO NOT touch the print head or cutter blade. Otherwise,

burning or injury of hand may result.

La page charge ...

Citizen CT-S2000DC Le manuel du propriétaire

Ce manuel convient également à

Citizen CT-S2000DC Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents