Sony WX-4500X Manuel utilisateur

Operating Instructions

사용설명서

US

Owner’s Record

The model and serial numbers are located on the bottom of the unit.

Record these numbers in the space provided below.

Refer to these numbers whenever you call upon your Sony dealer regarding this product.

Model No. WX-4500X Serial No.

WX-4500X

For installation and connections, see the supplied installation/connections manual.

설치 및 접속에 대해서는 부속된 설치/접속 사용설명서를 참조하여 주십시오.

KR

CT

Changer Control

Audio Master

2

Warning

This equipment has been tested and found to

comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This equipment

generates, uses, and can radiate radio frequency

energy and, if not installed and used in

accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference

will not occur in a particular installation. If this

equipment does cause harmful interference to

radio or television reception, which can be

determined by turning the equipment off and on,

the user is encouraged to try to correct the

interference by one or more of the following

measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment

and receiver.

– Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

– Consult the dealer or an experienced radio/TV

technician for help.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate this

equipment.

THIS DEVICE COMPLIES WITH PART 15

OF THE FCC RULES. OPERATION IS

SUBJECT TO THE FOLLOWING TWO

CONDITIONS;

(1) THIS DEVICE MAY NOT CAUSE

HARMFUL INTERFERENCE, AND

(2) THIS DEVICE MUST ACCEPT ANY

INTERFERENCE RECEIVED, INCLUDING

INTERFERENCE THAT MAY CAUSE

UNDESIRED OPERATION.

CAUTION

The use of optical instruments with this product

will increase eye hazard.

Welcome !

Thank you for purchasing this Sony Changer

Control Audio Master. You can enjoy its various

features even more with:

• Optional CD/MD units (both changers and

players)*

1

.

• CD TEXT information (displayed when a CD

TEXT disc*

2

is played).

• Optional controller accessory

Rotary commander RM-X4S

Card remote commander RM-X114

*1 This unit works with Sony products only.

*2 A CD TEXT disc is an audio CD that includes

information such as the disc name, artist name,

and track names. This information is recorded on

the disc.

3

Table of Contents

Location of controls . . . . . . . . . . . . . . . . . . . 4

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Notes on discs . . . . . . . . . . . . . . . . . . . . . . . . 7

Notes on Cassettes . . . . . . . . . . . . . . . . . . . . 8

Getting Started

Resetting the unit . . . . . . . . . . . . . . . . . . . . . 8

Setting the clock . . . . . . . . . . . . . . . . . . . . . . 9

CD Player

CD/MD Unit (optional)

Playing a disc . . . . . . . . . . . . . . . . . . . . . . . . 9

Display items . . . . . . . . . . . . . . . . . . . . . . . 10

Playing tracks repeatedly

— Repeat Play . . . . . . . . . . . . . . . . . . . . 10

Playing tracks in random order

— Shuffle Play . . . . . . . . . . . . . . . . . . . . 10

Labeling a CD

— Disc Memo. . . . . . . . . . . . . . . . . . . . . 11

Locating a disc by name

— List-up . . . . . . . . . . . . . . . . . . . . . . . . 12

Selecting specific tracks for playback

— Bank. . . . . . . . . . . . . . . . . . . . . . . . . . 12

Cassette Player

Listening to a tape . . . . . . . . . . . . . . . . . . . 13

Playing a tape in various modes . . . . . . . . . 14

Radio

Storing stations automatically

— Best Tuning Memory (BTM) . . . . . . 14

Receiving the stored stations . . . . . . . . . . . 15

Storing only the desired stations . . . . . . . . 15

Storing station names

— Station Memo . . . . . . . . . . . . . . . . . . 16

Tuning in a station through a list

— List-up. . . . . . . . . . . . . . . . . . . . . . . . 17

Other Functions

Using the rotary commander . . . . . . . . . . . 17

Adjusting the sound characteristics . . . . . . 19

Quickly attenuating the sound . . . . . . . . . . 19

Changing the sound and display settings

— Menu . . . . . . . . . . . . . . . . . . . . . . . . . 19

Setting the Dynamic Soundstage Organizer

(DSO) . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Setting the equalizer . . . . . . . . . . . . . . . . . . 20

Adjusting the front and rear volume . . . . . 21

Adjusting the volume of the

subwoofer(s) . . . . . . . . . . . . . . . . . . . . . 22

Selecting the spectrum analyzer . . . . . . . . 22

Additional Information

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 23

Specifications . . . . . . . . . . . . . . . . . . . . . . . 24

Troubleshooting . . . . . . . . . . . . . . . . . . . . . 25

Error displays/Messages . . . . . . . . . . . . . . 27

4

Location of controls

SEEK/AMSSEEK/AMS

TAPE

CD

EQ7DSO

OFF

SCRL

SA

SOUND

MENU

DSPL

AT T

SOURCE

MODE

5

Refer to the pages listed for details.

: During CD/MD playback : During tape playback : During radio reception

: During menu mode

a Frequency select switch (located on the

left side of the unit)

See “Frequency select switch” in the

Installation/Connections manual.

b DSO button 20

c SCRL (scroll) button 10

d Display window

e Receptor for the card remote

commander

f EQ7 button 20

g CD Z (eject) button 9

h DSPL (display mode change) button

10, 11, 16

i OFF (Stop/Power off) button* 8, 9, 13

j SOUND button 19, 21, 22

k MENU button 9, 10, 11, 12, 13, 14, 15,

16, 20, 21, 22

l SA (spectrum Analyzer) button 22

m SEEK/AMS buttons (–/+)

9

13

15

9, 10, 11, 12, 13, 14, 15, 16, 19,

20, 21, 22

n Jog roller

Jog roller usually functions as a volume

control except in some adjusting modes.

11, 12

15, 16, 17

9, 10, 11, 12, 13, 14, 15, 16, 20,

21, 22

o ATT button 19

p MODE (o) button

10, 11

13, 14

14, 15

q SOURCE (Power on/CD/MD/Tape/

Radio) button 9, 10, 11, 13, 14, 15, 19,

20, 21, 22

r Reset button 8

s TAPE Z (eject) button 13

* Warning when installing in a car without

an ACC (accessory) position on the

ignition switch

After turning off the ignition, be sure to press

(OFF) on the unit for 2 seconds to turn off the

clock display.

Otherwise, the clock display does not turn off and

this causes battery drain.

CD/MD

TAPE RADIO

MENU

CD/MD

TAPE

RADIO

MENU

CD/MD

RADIO

MENU

CD/MD

TAPE

RADIO

mn

In menu mode, the currently selectable directions are indicated with a “v” in the display.

continue to next page t

S

E

K

/A

M

S

E

K

/A

M

S

To select leftwards/.

To select rightwards/>

To select upwards

To select downwards

6

The corresponding buttons of the card

remote commander control the same

functions as those on this unit.

a DSPL button

b MENU button

c SOURCE button

d SEEK (</,) buttons

e SOUND button

f OFF button

g VOL (–/+) buttons

h MODE button

i LIST button

j DISC/PRESET (M/m) buttons

k ENTER button

l ATT button

Note

If the unit is turned off by pressing (OFF) for 2

seconds, it cannot be operated with the card remote

commander unless (SOURCE) on the unit is pressed,

or a CD or cassette is inserted to activate the unit first.

Tip

Refer to “Replacing the lithium battery” for details on

how to replace the batteries (page 23).

Precautions

• If your car was parked in direct sunlight, allow

the unit to cool off before operating it.

• Power antennas will extend automatically

while you select the radio reception.

• If no power is being supplied to the unit, check

the connections first. If everything is in order,

check the fuse.

• If no sound comes from the speakers of a two-

speaker system, set the fader control to the

center position.

• When a tape is played back for a long period,

the cassette may become warm because of the

built-in power amplifier. However, this is not a

sign of malfunction.

• Do not use the CUSTOM FILE feature while

driving, or perform any other function which

could divert your attention from the road.

If you have any questions or problems

concerning your unit that are not covered in this

manual, please consult your nearest Sony dealer.

Moisture condensation

On a rainy day or in a very damp area, moisture

condensation may occur inside the lenses and

display of the unit. Should this occur, the unit

will not operate properly. In such a case, remove

the disc and wait for about an hour until the

moisture has evaporated.

To maintain high quality sound

Be careful not to splash juice or other soft drinks

onto the unit or tapes.

Card remote commander RM-X114

(optional)

DISC

–

ATTOFF

DSPL MODE

SOURCE

DISC

+

VOL

+

–

PRESET

+

SEEK

+

SEEK

–

PRESET –

SOUND

EN

T

ER

MENU

LIST

7

Notes on discs

• To keep the disc clean, do not touch the surface.

Handle the disc by its edge.

• Keep your discs in their cases or disc

magazines when not in use.

Do not subject the discs to heat/high

temperature. Avoid leaving them in parked cars

or on dashboards/rear trays.

• Do not attach labels, or use discs with sticky

ink/residue. Such discs may stop spinning

when used, causing a malfunction, or may ruin

the disc.

• Discs with non-standard shapes (e.g., heart,

square, star) cannot be played on this unit.

Attempting to do so may damage the unit. Do

not use such discs.

• You cannot play 8 cm (3 in.) CDs.

• Before playing, clean the discs with a

commercially available cleaning cloth. Wipe

each disc from the center out. Do not use

solvents such as benzine, thinner, commercially

available cleaners, or antistatic spray intended

for analog discs.

Notes on CD-R/CD-RW discs

• You can play CD-Rs (recordable CDs)/CD-

RWs (rewritable CDs) designed for audio use

on this unit.

Look for these marks to distinguish CD-Rs/

CD-RWs for audio use.

These marks denote that a disc is not for audio

use.

• Some CD-Rs/CD-RWs (depending on the

equipment used for its recording or the

condition of the disc) may not play on this unit.

• You cannot play a CD-R/CD-RW that is not

finalized*.

* A process necessary for a recorded CD-R/CD-RW

disc to be played on the audio CD player.

8

Notes on Cassettes

Cassette care

• Do not touch the tape surface of a cassette, as

any dirt or dust will contaminate the heads.

• Keep cassettes away from equipment with

built-in magnets such as speakers and

amplifiers, as erasure or distortion on the

recorded tape could occur.

• Do not expose cassettes to direct sunlight,

extremely cold temperatures, or moisture.

• Slack in the tape may cause the tape to be

caught in the machine. Before you insert the

tape, use a pencil or similar object to turn the

reel and take up any slack.

• Distorted cassettes and loose labels can cause

problems when inserting or ejecting tapes.

Remove or replace loose labels.

• The sound may become distorted while playing

the cassette. The cassette player head should be

cleaned after each 50 hours of use.

The use of cassettes longer than 90 minutes

is not recommended except for long

continuous play

The tape used for these cassettes is very thin and

tends to stretch easily.

Frequent playing and stopping of these tapes

may cause them to become entangled in the

cassette deck mechanism.

Getting Started

Resetting the unit

Before operating the unit for the first time, or

after replacing the car battery or changing the

connections, you must reset the unit.

Press the reset button with a pointed object, such

as a ball-point pen.

Notes

• Pressing the reset button will erase the clock setting

and some stored contents.

• When you connect the power supply cord to the unit

or reset the unit, wait for about 10 seconds before

you insert a CD or cassette. If you insert a CD or

cassette within these 10 seconds, the unit will not be

reset, and you will have to press the reset button

again.

• When you press the reset button or (OFF), the

demonstration display will appear in the display. To

deactivate the demonstration display, set the Motion

Display mode to off (page 19).

Slack

SEEK/AMS

MD

CD

EQ7DSO

OFF

SCRL

SA

SOUND

MENU

DSPL

ATT

SOURCE

SEEK/AMS

MODE

Reset button

9

Setting the clock

The clock uses a 12-hour digital indication.

Example: To set the clock to 10:08

1 Press (MENU), then rotate the jog

roller until “Clock” appears.

1 Push the jog roller.

The hour indication flashes.

2 Rotate the jog roller to set the hour.

3 Press (SEEK/AMS +).

The minute indication flashes.

4 Rotate the jog roller to set the

minute.

2 Push the jog roller.

The clock starts. After the clock setting is

completed, the display returns to normal play

mode.

Tip

When Motion Display mode is set to “off” or “1,” and

D.Info mode is set to “on,” the time is always displayed

(page 19).

Note

If your car has no ACC position on the ignition switch,

be sure to turn the unit on by pressing (SOURCE) or

inserting a CD or cassette before setting the clock.

CD Player

CD/MD Unit (optional)

In addition to playing a CD with this unit, you

can also control external CD/MD units.

Note

If you connect an optional CD unit with the CD TEXT

function, the CD TEXT information will appear in the

display when you play a CD TEXT disc.

Playing a disc

(With this unit)

Insert the disc (labeled side up).

Playback starts automatically.

If a disc is already inserted, press (SOURCE)

repeatedly until “CD” appears to start playback.

Notes

• When the last track on the disc is over, playback

restarts from the first track of the disc.

• With optional unit connected, playback of the same

source will continue on to the optional CD/MD unit.

To Press

Stop playback (OFF)

Eject the disc CD Z

Skip tracks

– Automatic

Music Sensor

(SEEK/AMS) (./>)

[once for each track]

Fast-forward/

reverse

– Manual Search

(SEEK/AMS) (m/M)

[hold to desired point]

continue to next page t

10

(With optional unit)

1 Press (SOURCE) repeatedly to select

“CD” or “MD.”

2 Press (MODE) repeatedly until the

desired unit appears.

Playback starts.

Locating a disc

— Disc selection

(see “Locating a disc by name” on page 12.)

Tip

With the optional MG Memory Stick System-up Player

MGS-X1 connected to the unit, press (SOURCE) to

select “MD,” then press (MODE) to select “MS.”

Display items

When the disc/track changes, any prerecorded

title*

1

of the new disc/track is automatically

displayed (if the Auto Scroll function is set to

“on,” names exceeding 13 characters will be

scrolled (page 19)).

*1 When pressing (DSPL), “NO D.Name” or “NO

T.Name” indicates that there is no Disc Memo

(page 11) or prerecorded name to display.

*2 Only for CD TEXT discs with the artist name.

Notes

• Some characters cannot be displayed.

• For some CD TEXT discs with very many

characters, information may not scroll.

• This unit cannot display the artist name for each

track of a CD TEXT disc.

• The source name, disc name, track title, and

elapsed playing time may not be displayed

depending on the Motion or SA settings.

Tip

When Auto scroll is set to off and the disc/track name

is changed, the disc/track name does not scroll.

Playing tracks repeatedly

— Repeat Play

The disc in the main unit will repeat a track or

the entire disc when it reaches the end. For repeat

play, you can select:

• Repeat 1 — to repeat a track.

• Repeat 2* — to repeat a disc.

* Available only when one or more optional CD/MD

units are connected.

1 Press (MENU), then rotate the jog

roller until “Repeat” appears.

2 Press (SEEK/AMS +) repeatedly to

select the desired setting.

3 Push the jog roller.

Repeat Play starts.

To return to normal play mode, select “Repeat

off ” in step 2.

Playing tracks in random

order

— Shuffle Play

You can select:

• Shuffle 1 — to play the tracks on the current

disc in random order.

• Shuffle 2*

1

— to play the tracks in the current

optional CD (MD) unit in random order.

• Shuffle all*

2

— to play all the tracks in all the

connected CD (MD) units (including this unit)

in random order.

*1 Available only when one or more optional CD (MD)

units are connected.

*2 Available only when one or more optional CD units,

or two or more optional MD units are connected.

1 Press (MENU), then rotate the jog

roller until “Shuffle” appears.

2 Press (SEEK/AMS +) repeatedly to

select the desired setting.

3 Push the jog roller.

Shuffle Play starts.

To return to normal play mode, select “Shuffle

off ” in step 2.

To Press

Switch display

item

(DSPL)

Scroll display item (SCRL)

Track

number

Disc

number

Elapsed

playing time

Displayable items

• Disc name*

1

/artist name*

2

• Track title*

1

11

Note

“Shuffle all” will not shuffle tracks between CD units

and MD units.

Labeling a CD

— Disc Memo (For a CD unit with the

CUSTOM FILE function)

You can label each disc with a custom name

(Disc Memo). You can enter up to 8 characters

for a disc. If you label a CD, you can locate the

disc by name (page 12).

Caution

Do not use the CUSTOM FILE feature while

driving, or perform any other function which

could divert your attention from the road.

1 Start playing the disc you want to

label.

2 Press (MENU), then rotate the jog

roller until “Name Edit” appears.

3 Push the jog roller.

The unit will repeat the disc during the

labeling procedure.

4 Enter the characters.

1 Rotate the jog roller to select the

desired character.

A t B t C ... t 0 t 1 t 2 ... t +

t – t

*

... t * t A

* (blank space)

2 Press (SEEK/AMS +) after locating

the desired character.

If you press (SEEK/AMS -), you can move

back to the left.

3 Repeat steps 1 and 2 to enter the

entire name.

5 To return to normal CD play mode,

push the jog roller.

Tips

• Simply overwrite or enter “” to correct or erase a

name.

• There is another way to start labeling a CD: Push

the jog roller for 2 seconds instead of performing

steps 2 and 3.

• You can label CDs on a unit without the CUSTOM

FILE function if that unit is connected along with a

CD unit that has the function. The Disc Memo will be

stored in the memory of the CD unit with the

CUSTOM FILE function.

Note

Repeat/shuffle play is suspended until the Name Edit

is complete.

Viewing the Disc Memo

As a display item, the Disc Memo always takes

priority over any original CD TEXT information.

Tip

To find out about other items that can be displayed,

see page 10.

Erasing the Disc Memo

1 Press (SOURCE) repeatedly to select

“CD.”

2 Press (MODE) repeatedly to select the

CD unit storing the Disc Memo.

3 Press (MENU), then rotate the jog

roller until “Name Delete” appears.

4 Push the jog roller.

The stored names will appear.

5 Rotate the jog roller to select the disc

name you want to erase.

The stored names will appear.

6 Push the jog roller for 2 seconds.

The name is erased.

Repeat steps 5 and 6 if you want to erase

other names.

7 Press (MENU) twice.

The unit returns to normal CD play mode.

Notes

• When the Disc Memo for a CD TEXT disc is erased,

the original CD TEXT information is displayed.

• If you cannot find the Disc Memo you want to erase,

try selecting a different CD unit in step 2.

To Press

View (DSPL) during CD/CD

TEXT disc playback

12

Locating a disc by name

— List-up (For a CD unit with the CD TEXT/

CUSTOM FILE function, or an MD unit)

You can use this function for discs that have been

assigned custom names*

1

or for CD TEXT

discs*

2

.

*1 Locating a disc by its custom name: when you

assign a name for a CD (page 11) or an MD.

*2 Locating discs by the CD TEXT information: when

you play a CD TEXT disc on a CD unit with the CD

TEXT function.

1 During playback, push the jog roller.

The name assigned to the current disc appears

in the display.

2 Rotate the jog roller until you find the

desired disc.

3 Push the jog roller to play the disc.

Notes

• Some letters cannot be displayed (exception: Disc

Memo).

• If you do not perform any operation for more than 5

seconds with the list displayed, the display returns to

normal playback mode.

Operating with the card remote

commander

1 During playback, press (LIST).

2 Press (DISC/PRESET -) or

(DISC/PRESET +) repeatedly until you

find the desired disc.

3 Press (ENTER).

Selecting specific tracks for

playback

— Bank (For a CD unit with the CUSTOM FILE

function)

If you label the disc, you can set the unit to skip

or play the tracks of your choice.

1 Start playing the disc you want to

label.

2 Press (MENU), then rotate the jog

roller until “Bank Sel” appears.

3 Push the jog roller.

4 Label the tracks.

1Press (SEEK/AMS -) or (SEEK/AMS +)

repeatedly to select the track you

want to label.

2Push the jog roller to select “Play”

or “Skip.”

5 Repeat step 4 to set “Play” or “Skip”

for all the tracks.

6 Press (MENU) twice.

The unit returns to normal CD play mode.

Notes

• You can set “Play” and “Skip” for up to 24 tracks.

• You cannot set “Skip” for all the tracks on a CD.

13

Playing specific tracks only

You can select:

• Bank on — to play the tracks with the “Play”

setting.

• Bank inv (Inverse) — to play the tracks with

the “Skip” setting.

1 During playback, press (MENU), then

rotate the jog roller until “Bank on,”

“Bank inv,” or “Bank off” appears.

2 Press (SEEK/AMS +) repeatedly until

the desired setting appears.

3 Push the jog roller.

Playback starts from the track following the

current one.

To return to normal play mode, select “Bank off”

in step 2.

Cassette Player

Listening to a tape

Insert a cassette.

Playback starts automatically.

If a cassette is already inserted, press (SOURCE)

repeatedly until “FORWARD B” or

“REVERSE b” appears to start playback.

FORWARD B: The side facing up is played.

REVERSE b: The side facing down is played.

Tip

To start playback during fast-forward or rewind, press

(MODE) (o).

Note

The AMS function may not work when:

– the blanks between tracks are shorter than 4

seconds.

– there is noise between tracks.

– there are long sections of low volume or quiet

sections.

To Press

Change the tape’s

playback direction

(MODE) (o)

Stop playback (OFF)

Eject the cassette TAPE Z

Skip tracks

– Automatic

Music Sensor

(SEEK/AMS) (./>)

[once for each track]

Fast-forward/

Rewind

(SEEK/AMS) (m/M)

[hold for 2 seconds]

14

Playing a tape in various

modes

You can play the tape in various modes:

• Met

al lets you play a metal or CrO2 tape.

• BL.Skip (Blank Skip) skips blanks longer than

8 seconds.

• ATA (Automatic Tuner Activation) turns on the

tuner automatically when fast-winding the tape.

• NR (Dolby NR) lets you select the Dolby* NR

B system.

* Manufactured under license from Dolby

Laboratories. “Dolby” and the double-D symbol are

trademarks of Dolby Laboratories.

1 During tape playback, press (MENU).

2 Rotate the jog roller until the desired

mode appears.

3 Press (SEEK/AMS +) to select “on.”

Example: ATA mode

4 Push the jog roller.

Play mode starts.

To return to normal playback mode, select “off”

in step 3.

Note

Power antennas will extend when ATA is set to on.

Playing tracks repeatedly

— Repeat Play

1 Press (MENU), then rotate the jog

roller until “Repeat” appears.

2 Press (SEEK/AMS +) to select “on.”

3 Push the jog roller.

Repeat play starts.

To return to normal playback mode, select

“Repeat off” in step 2.

Tip

During repeat playback, press (MODE). “REP”

disappears from the display and repeat mode is

canceled.

Radio

The unit can store up to 10 stations per band

(FM1, FM2, and AM).

Caution

When tuning in stations while driving, use Best

Tuning Memory to prevent accidents.

Storing stations

automatically

— Best Tuning Memory (BTM)

The unit selects the stations with the strongest

signals within the selected band, and stores them

in the order of their frequency.

1 Press (SOURCE) repeatedly to select

the radio.

2 Press (MODE) repeatedly to select the

band.

3 Press (MENU), then rotate the jog

roller until “B.T.M” appears.

4 Push the jog roller.

A beep sounds when the setting is stored.

Notes

• If only a few stations can be received due to weak

signals, some stored numbers will retain their former

settings.

• When a number is indicated in the display, the unit

starts storing stations from the one currently

displayed.

15

Receiving the stored stations

1 Press (SOURCE) repeatedly to select

the radio.

2 Press (MODE) repeatedly to select the

band.

3 Push the jog roller.

4 Rotate the jog roller until you find the

desired station.

5 Push the jog roller to tune in the

desired station.

Tip

Press (DISC/PRESET -) or (DISC/PRESET +) on the

card remote commander to receive the stations in the

order they are stored in memory (Preset Search

function).

If preset tuning does not work

Press (SEEK/AMS -) or (SEEK/AMS +) to

search for the station (automatic

tuning).

Scanning stops when the unit receives a

station. Repeat until the desired station is

received.

Tips

• If automatic tuning stops too frequently, turn on the

Local Seek to limit seek to stations with stronger

signals (see “Changing the sound and display

settings” on page 19).

• If you know the frequency of the station you want to

listen to, press and hold (SEEK/AMS -) or

(SEEK/AMS +) to locate the approximate frequency,

then press (SEEK/AMS) repeatedly to fine adjust to

the desired frequency (manual tuning).

If FM stereo reception is poor

Select monaural reception mode.

(see “Changing the sound and display

settings” on page 19). The sound improves,

but becomes monaural (“ST” disappears).

Tip

If FM broadcasts are difficult to hear, set DSO to off.

Automatic reception frequency

adjustment

— IF Auto function

While receiving FM stereo, interference from a

nearby station may make listening difficult. In

such cases, the “IF Auto” function of this unit

will automatically narrow the reception

frequency to eliminate noise. For this reason,

some FM stereo broadcasts may become

monaural. If you would like to hear such

broadcasts in stereo, manually switch to the

“Wide” setting.

1 During FM radio reception, press

(MENU).

2 Rotate the jog roller until “IF Auto”

appears.

3 Press (SEEK/AMS +) to select “Wide.”

4 Push the jog roller.

Note

Return to the “IF Auto” setting from the “Wide” setting

if interference makes FM stereo difficult to listen to.

Storing only the desired

stations

You can manually preset the desired stations.

1 Press (SOURCE) repeatedly to select

the radio.

2 Press (MODE) repeatedly to select the

band.

3 Press (SEEK/AMS -) or (SEEK/AMS +) to

tune in the station that you want to

store.

4 Push the jog roller.

5 Rotate the jog roller to select the

stored number.

6 Push the jog roller for 2 seconds until

“Memory” appears.

The stored station indication appears in the

display.

Note

If you try to store another station on the same stored

number, the previously stored station will be erased.

16

Storing station names

— Station Memo

You can assign a name to each radio station and

store it in memory. The name of the station

currently tuned in appears in the display. You can

assign a name using up to 8 characters for a

station.

Storing the station names

1 Tune in a station whose name you

want to store.

2 Press (MENU), then rotate the jog

roller until “Name Edit” appears.

3 Push the jog roller.

4 Enter the characters.

1 Rotate the jog roller to select the

desired character.

A t B t C ... t 0 t 1 t 2 ... t +

t – t

*

... t * t A

* (blank space)

2 Press (SEEK/AMS +) after locating

the desired character.

If you press (SEEK/AMS -), you can move

back to the left.

3 Repeat steps 1 and 2 to enter the

entire name.

5 Push the jog roller.

Tips

• Simply overwrite or enter “” to correct or erase a

name.

• There is another way to start storing station names:

Push the jog roller for 2 seconds instead of

performing steps 2 and 3.

Displaying the station name

Switch the display item to frequency or station

name*.

* If the station name is not stored, “NO Name”

appears in the display for one second.

Erasing the station name

1 During radio reception, press (MENU),

then rotate the jog roller until “Name

Delete” appears.

2 Push the jog roller.

3 Rotate the jog roller to select the

station whose name you want to

erase.

4 Push the jog roller for 2 seconds.

The name is erased.

Repeat steps 3 to 4 if you want to erase other

names.

5 Press (MENU) twice.

The unit returns to normal radio reception

mode.

Note

If you have already erased all of the station names,

“NO Data” appears in step 4.

To Press

Switch display

item

(DSPL) during radio

reception

17

Tuning in a station through a

list

— List-up

1 During radio reception, push the jog

roller.

The frequency or the name assigned to the

station currently tuned in flashes.

2 Rotate the jog roller until you find the

desired station.

If no name is assigned to the selected station,

the frequency appears in the display.

3 Push the jog roller to tune in the

desired station.

Note

If you do not perform any operation for more than 5

seconds with the list displayed, the display returns to

normal radio reception mode.

Operating with the card remote

commander

1 During radio reception, press (LIST).

2 Press (DISC/PRESET -) or

(DISC/PRESET +) repeatedly until you

find the desired station.

3 Press (ENTER).

Other Functions

You can also control the unit (and optional CD/

MD units) with a rotary commander

(optional).

Using the rotary commander

First, attach the appropriate label depending on

how you want to mount the rotary commander.

The rotary commander works by pressing

buttons and/or rotating controls.

By pressing buttons

Press To

(SOURCE)

Change source (radio/CD/

MD*

1

/Tape)/Power on

(MODE)

Change operation

(radio band/CD unit*

1

/MD

unit*

1

/tape playback

direction)

(ATT) Attenuate sound

(OFF)*

2

Stop playback or radio

reception/Power off

(SOUND) Adjust the sound menu

(DSPL) Change the display item

continue to next page t

SOUND

DSPL

MODE

SOUND

DSPL

MODE

OFF

Rotate the VOL control

to adjust the volume.

(SOURCE)

(SOUND)

(ATT)

(MODE)

(DSPL)

(OFF)

18

*1 Only if the corresponding optional equipment is

connected.

*2 If your car has no ACC (accessory) position on the

ignition key switch, be sure to press (OFF) for 2

seconds to turn off the clock indication after turning

off the ignition.

By rotating the control

Rotate and release to:

– Skip tracks on the disc.

– Locate the beginning of tracks on the tape.

– Tune in stations automatically.

Rotate, hold, and release to:

– Fast-forward/reverse a track.

– Fast-wind the tape.

– Find a station manually.

Tip

To start playback while fast-winding the tape, press

(MODE).

By pushing in and rotating the control

Push in and rotate the control to:

– Receive preset stations.

– Change the disc*.

* When an optional CD/MD unit is connected.

Changing the operative direction

The operative direction of controls is factory-set

as shown below.

If you need to mount the rotary commander on

the right hand side of the steering column, you

can reverse the operative direction.

Press (SOUND) for 2 seconds while

pushing the VOL control.

Tip

You can also change the operative direction of these

controls with the unit (see “Changing the sound and

display settings” on page 19).

SEEK/AMS

control

PRESET/

DISC control

To increase

To decrease

19

Adjusting the sound

characteristics

You can adjust the bass, treble, balance, fader,

and subwoofer volume.

The bass and treble levels and subwoofer volume

can be stored independently for each source.

1 Press (SOURCE) to select a source

(radio, CD, MD, or tape).

2 Press (SOUND) repeatedly to select

the item you want to adjust.

Each time you press (SOUND), the item

changes as follows:

BAS (bass) t TRE (treble) t

BAL (left-right) t FAD (front-rear) t

Sub (subwoofer volume)

3 Press (SEEK/AMS -) or (SEEK/AMS +) to

adjust the selected item.

When adjusting with the rotary commander,

press (SOUND) and rotate the VOL control.

Note

Adjust within 3 seconds after selecting the item.

Quickly attenuating the

sound

Press (ATT).

“ATT on” appears in the display momentarily.

To restore the previous volume level, press

(ATT) again.

Tip

When the interface cable of a car telephone is

connected to the ATT lead, the unit decreases the

volume automatically when a telephone call comes in

(Telephone ATT function).

Changing the sound and

display settings

— Menu

The following items can be set:

Set up

• Clock (page 9)

• Beep — to turn the beeps on or off.

• RM (Rotary Commander) — to change the

operative direction of the controls of the rotary

commander.

– Select “norm” to use the rotary commander

as the factory-set position.

– Select “rev” when you mount the rotary

commander on the right side of the steering

column.

• Key ill (Key illumination) — to change the

illumination of the unit’s buttons.

– Select “Auto” to have the buttons light up

only with the car lights on. (Functions only

when the illumination control lead is

connected to the car’s illumination feed.)

– Select “on” to light up the buttons.

Dspl (Display)

• D.Info (Dual Information) — to display the

clock and the play mode at the same time (on).

(Functions only when Motion is set to “1” or

“off.”)

• Dimmer — to change the brightness of the

display.

– Select “Auto” to dim the display only when

you turn the lights on. (Functions only when

the illumination control lead is connected to

the car’s illumination feed.)

– Select “on” to dim the display.

– Select “off” to deactivate the Dimmer.

• Display

– When Display is set to “off,” the display

comes on only during an operation.

• Motion (Motion Display) — to select the

Motion Display mode from “1,” “2,” and “off.”

• A.Scrl (Auto Scroll)*

– Select “on” to scroll all automatically

displayed names exceeding 13 characters.

– When Auto scroll is set to off and the disc/

track name is changed, the disc/track name

does not scroll.

* When no CD or MD is playing, this item will not

appear.

continue to next page t

20

Sound

• HPF (High pass filter) (page 21)

• LPF (Low pass filter) (page 22)

• Loud (Loudness) — to enjoy bass and treble

even at low volumes. The bass and treble will

be reinforced.

P.Mode (Play Mode)

• Local on/off (Local seek mode) (page 15)

– Select “on” to only tune into stations with

stronger signals.

• Mono on/off (Monaural mode) (page 15)

– Select “on” to hear FM stereo broadcast in

monaural. Select “off” to return to normal

mode.

• IF Auto/Wide (page 15)

1 Press (MENU).

To set A.Scrl, press (MENU) during CD/MD

Playback.

2 Rotate the jog roller until the desired

item appears.

3 Press (SEEK/AMS -) or (SEEK/AMS +) to

select the desired setting (Example:

“on” or “off”).

4 Push the jog roller.

After the mode setting is completed, the

display returns to normal play mode.

Notes

• The displayed item will differ depending on the

source.

• If you do not perform any operation for more than 5

seconds with the menu displayed, the display

returns to normal play mode.

Tip

You can easily switch among categories (“Set up,”

“Dspl,” “P.Mode,” “Sound,” and “Edit”) by pressing

(DISC/PRESET -) or (DISC/PRESET +) on the card

remote commander for 2 seconds.

Operating with the card remote

commander

1 Press (MENU).

2 Press (DISC/PRESET -) or

(DISC/PRESET +) repeatedly until the

desired item appears.

3 Press (SEEK/AMS -) or (SEEK/AMS +) to

select the desired setting.

4 Press (ENTER).

Setting the Dynamic

Soundstage Organizer (DSO)

If your speakers are installed into the lower part

of the doors, the sound will come from below

and may not be clear.

The DSO (Dynamic Soundstage Organizer)

function creates a more ambient sound as if there

were speakers in the dashboard (virtual

speakers).

You can store the DSO setting for each source.

1 Press (SOURCE) to select a source

(radio, CD, MD, or tape).

2 Press (DSO) repeatedly until “DSO

on” appears.

To cancel the DSO function, select “DSO off” in

step 2.

Notes

• Depending on the type of car interior or type of

music, DSO may not have a desirable affect.

• If FM broadcasts are difficult to hear, set DSO to off.

Setting the equalizer

You can select an equalizer curve for 7 music

types (Vocal, Club, Jazz, New Age, Rock,

Custom, and Xplod).

You can store a different equalizer setting for

each source.

Selecting the equalizer curve

1 Press (SOURCE) to select a source

(radio, CD, MD, or tape).

2 Press (EQ7) repeatedly until the

desired equalizer curve.

Each time you press (EQ7), the item

changes.

To cancel the equalizing effect, select “off.”

After 3 seconds, the display returns to the

normal playback mode.

Note

When DSO is set to on, equalizer settings are

automatically adjusted for best overall effect.

La page charge ...

Sony WX-4500X Manuel utilisateur

Sony WX-4500X Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents