Genie 3062 Maintenance Manual

Marque: Genie

Modèle: 3062

Catégorie: Porte de garage

Taper: Maintenance Manual

Within these pages you may see a QR

code for certain steps. Scan this code

to go directly to a video for that particular

installation and/or programming step.

Download a Code Reader app from your

app store.

INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER

HOMEOWNER: SAVE THIS MANUAL FOR FUTURE REFERENCE

BELT/CHAIN/SCREW DRIVE

GARAGE DOOR OPENER MODELS

2562, 2568, 3022, 3024, 3042, 3062 ,

3064, 4024, 4042, 4062, 4064, SC1200,

CB1000, CB1200

PROGRAMMING,

OPERATION &

MAINTENANCE

MANUAL

Includes factory programmed

INTELLICODE

Remote Control.

The included

Safe-T-Beam® system

MUST be installed to close the door. DO NOT use other brands or types.

Homelink® and Car2U® compatible.

For use ONLY with residential Sectional or One-Piece overhead garage doors.

39495503493

Alternate language manuals available at:

Idioma alternativo manuales disponibles en:

Autre langue manuels disponibles à:

www.GenieCompany.com

STOP

Need help or have questions?

For answers and assistance,

visit www.GenieCompany.com

or call Customer Service at: 1-800-35-GENIE

To reduce the risk of injury to persons or damage to property - use this opener only with a sectional or one-piece

residential door.

WARNING

Pour réduire le risque de blessures ou de dommages matériels, utilisez cet ouvre-porte uniquement pour une porte

à section ou monopièce.

AVERTISSEMENT

Scan code for a video of this installation or

visit: www.GenieCompany.com

Belt/Chain Drive

ScrewDrive

Serial Number Decal

Safety Information

Safety Noti cations ................................................. 4

Important Safety Instructions ............................. 5

Features

Safety Features ......................................................... 6

Opener Features ...................................................... 6

Programming Information

Introduction .............................................................. 7

Overview of Powerhead Controls...................... 7

Travel Limits

Closing Garage Door (DOWN Limit) ................. 8

Opening Garage Door (UP Limit)....................... 9

Force Control ...........................................................10

Contact Reverse Test ............................................10

Contact Reverse Adjustment ............................10

Remote Control Programming .........................11

Maintenance and Adjustments

Important Safety Instructions ...........................12

Regular Maintenance ...........................................13

Remote Battery Replacement ...........................13

Light Bulb Replacement .....................................14

Adjustment Guides ........................................ 14-15

Resetting Travel Limits .........................................15

Locating Safe-T-Beam® Pairs

.............................16

Wire Diagram ..........................................................16

Troubleshooting ........................................... 17-18

Optional Programming & Accessories

Clearing Memory for Remotes .........................19

Programming Vehicle Remotes ........................20

Programming Wireless Keypad ................. 21-22

One-Piece Door Supplement .........................23

Parts ................................................................... 24-27

DASMA Information ................................... 28-31

Warranty ..................................................................32

INDEX

SAVE THESE INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

FCC Part 15.21 Statement:

Changes or modi cations not expressly

approved by the party responsible for

compliance could void the user’s authority to

operate the equipment.

FCC / IC Statement:

This device complies with FCC Part 15

and Industry Canada licence-exempt RSS

standard(s). Operation is subject to the

following two conditions: (1) this device

may not cause harmful interference, and

(2) this device must accept any interference

received, including interference that may cause

undesired operation of the device.

Le présent appareil est conforme aux CNR

d’Industrie Canada applicables aux appareils

radio exempts de licence. L’exploitation est

autorisée aux deux conditions suivantes : (1)

l’appareil ne doit pas produire de brouillage,

et (2) l’utilisateur de l’appareil doit accepter

tout brouillage radioélectrique subi, même si le

brouillage est susceptible d’en compromettre le

fonctionnement.

DO NOT RETURN PRODUCT TO STORE

If you require assistance or have any questions,

a knowledgeable Genie Service Technician is just

a phone call away at:

1-800-35-GENIE (1-800-354-3643)

Or visit our website at:

www.GenieCompany.com

Thank you for purchasing a

Genie® brand garage door

opener. The leader in garage door

opener technology.

Before setting up your new garage door opener, please locate and record the model plate on the

opener. This information will be necessary should you seek technical support via our website,

customer support department or local servicing Genie dealer.

Model Number:______________________________

Serial Number:_______________________________

Please take a moment to preview this manual and assembly poster

(if applicable) to ensure that you have the proper tools and skill set to

install a new garage door opener. Pay particular attention to all Safety

Warnings, Cautions and Information. Remember, your garage door is

the largest and heaviest moving object in your home.

and Safe-T-Beam, are registered trademarks of The Genie Company. TriloG and GPower are trademarks of GMI Holdings, Inc d/b/a The Genie

Company. All other trademarks are property of their rightful owners. Consistent with our policy of continuing product improvements,

we reserve the right to change product speci cations without prior notice or obligations. HomeLink is a registered trademark of Gentex

Corporation. Car2U is a registered trademark of Lear Corporation.

SAFETY NOTIFICATIONS & INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

OVERVIEW OF POTENTIAL HAZARDS

READ THIS SAFETY INFORMATION

Garage doors are large, heavy objects that move with the help of springs under high tension and electric motors. Since moving objects, springs under tension,

and electric motors can cause injuries, your safety and the safety of others depend on you reading the information in this manual. If you have questions or do

not understand the information presented, call your nearest trained door system technician or visit our website at www.geniecompany.com.

CONVENTIONS USED IN THESE INSTRUCTIONS

The following safety alert symbol and signal words are used throughout this manual to call attention to and identify di erent levels of hazards and special

instructions.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert

symbol and the word

“DANGER”, “WARNING”,

“CAUTION”.

•

DANGER

indicates an imminently hazardous situation which, if NOT avoided, will result in death or serious injury.

•

WARNING

indicates a potentially hazardous situation which, if NOT avoided, could result in death or serious injury.

•

CAUTION

indicates a potentially hazardous situation which, if NOT avoided, may result in injury or property damage.

•

The word

NOTE

s used to indicate important steps to be followed or important considerations.

Tous les messages concernant la sécurité seront indiqués après un symbole d’alerte de la sécurité et l’une des mentions suivantes “DANGER”,

”AVERTISSEMENT” ou “MISE EN GARDE”.

• DANGER signale une situation dangereuse imminente qui, si elle n’est pas évitée, risque d’entraîner des blessures graves, voire mortelles.

• AVERTISSEMENT signale une situation potentiellement dangereuse qui, si elle n’est pas évitée, risque d’entraîner la mort ou des blessures

graves.

• MISE EN GARDE signale une situation potentiellement dangereuse qui, si elle n’est pas évitée, risque d’entraîner des blessures ou des

dommages matériels.

• Le terme REMARQUE est utilisé pour signaler les étapes importantes à suivre ou d’importants éléments à prendre en considération.

IMPORTANTES CONSIGNES DE SÉCURITÉ

DANGER POTENTIEL EFFET PRÉVENTION

PORTE EN MOUVEMENT

AVERTISSEMENT

Pourrait entraîner des

blessures graves voire la mort

Utiliser uniquement si la porte est en vue et libre de tout obstacle.

Ne laisser personne se tenir dans l’ouverture de la porte pendant

qu’elle est en mouvement.

Ne pas permettre aux enfants de jouer avec l’opérateur de la porte.

Ne pas modi er la commande de l’opérateur à contact momentané

à moins qu’un moyen d’inversion externe soit installé.

Ne pas faire fonctionner une porte qui bloque ou dont le ressort

est cassé.

CHOC ÉLECTRIQUE

AVERTISSEMENT

Pourrait entraîner des

blessures graves voire la mort

Couper le courant avant d’enlever le couvercle de l’opérateur.

Lorsque le couvercle doit être remplacé, s’assurer que les  ls ne sont

ni coincés ni près des pièces mobiles.

L’opérateur doit être correctement mis à la terre.

TENSION ÉLEVÉE RESSORT

AVERTISSEMENT

Pourrait entraîner des

blessures graves voire la mort

Ne pas essayer d’enlever, réparer ni ajuster les ressorts ou

toute autre pièce à laquelle le ressort de la porte est attaché, y

compris blocs de bois, supports en acier, câbles ou autres articles

semblables.

Les réparations et les réglages doivent être e ectués par

technicien quali é qui se sert d’outils appropriés et qui respecte les

instructions.

POTENTIAL HAZARD EFFECT PREVENTION

MOVING DOOR

WARNING

Could result in Serious

Injury of Death

Do Not operate unless the doorway is in sight and free of

obstructions. Keep people clear of opening while door is moving.

Do Not allow children to play with the door opener.

Do Not change opener control to momentary contact unless and

external reversing means is installed.

Do Not operate a door that jambs or one that has a broken spring.

ELECTRICAL SHOCK

WARNING

Could cause Serious

Injury or Death

Turn o electrical power before removing opener cover.

When replacing the cover, make sure wires are not pinched or near

moving parts.

Opener must be electrically grounded.

HIGH SPRING TENSION

WARNING

Could cause Serious

Injury or Death

Do Not try to remove, repair or adjust springs or anything to which

door spring parts are fastened such as wood block, steel brackets,

cables or any other structure or like item.

Repairs and adjustments must be made by a trained service

representative using proper tools and instructions.

IMPORTANT INSTALLATION INSTRUCTIONS

IMPORTANTES INSTRUCTIONS D’INSTALLATION

WARNING

Opener is equipped with grounded electrical plug for

your protection, and only  ts grounded electrical

outlets. DO NOT alter plug in any way! If your have no

grounded outlets, have one installed by a licensed

electrician. Opener must be properly grounded to prevent

personal injury and equipment damage. NEVER USE AN

EXTENSION CORD! Check local building codes for any

requirement that you must have a permanent hard-wired

connection. Permanent hard-wired connections must be

performed by a licensed electrician using proper tools and

instructions.

AVERTISSEMENT

L’opérateur, qui est équipé d’une prise électrique mise à la terre

pour votre protection est compatible uniquement avec des

prises électriques mises à la terre. NE PAS modi er la  che dune

quelconque manière. Si vous n’avez pas de prises mises à la terre,

faites-en installer par un électricien agréé. L’opérateur doit être

correctement mis à la terre pour éviter les blessures corporelles et

des dommages matériels. NE JAMAIS UTILISER DE RALLONGE!

Véri ez les codes locaux des bâtiments pour connexions câblées

permanente. Les connexions câblées permanentes doivent

être e ectuées par un électricien agréé qui se servira d’outils

appropriés et respectera les consignes.

WARNING

TO REDUCE THE RISK OF SEVERE INJURY OR

DEATH

READ AND FOLLOW ALL SAFETY, INSTALLATION AND OPERATION INSTRUCTIONS. If you have any questions or do not

understand an instruction, call The Genie Company.

• DO NOT install opener on an improperly balanced door. An improperly balanced door could cause severe injury. Repairs

and adjustments to cables, spring assembly and other hardware must be made by a trained service person using proper

tools and instructions.

• Remove all ropes, and disable all locks connected to the door before installing opener.

• Where possible, install the door opener 7 feet or more above the  oor. For products having an emergency release,

mount the emergency release within reach, but at least 6 feet above the  oor and avoiding contact with vehicles to

avoid accidental release. DO NOT use emergency release cord to pull door.

• DO NOT connect the opener to the source of power until instructed to do so.

• Locate the wall control button: A) Within sight of door. B) At a minimum height of 5 feet, so small children cannot reach

it. C) Away from all moving parts of the door.

• Install the entrapment WARNING label next to the wall button or console, in a prominent location. Install the emergency

release handle on the emergency release cord.

• The opener must reverse when the door contacts a 1-1/2 inch high object on the  oor at the center of the doorway. This

is about the size of a 2” x 4” board laid  at.

AVERTISSEMENT

POUR RÉDUIRE LES RISQUES DE BLESSURES GRAVES VOIRE

MORTELLES

LIRE ET SUIVRE ATTENTIVEMENT TOUTES LES INSTRUCTIONS D’INSTALLATION ET DE FONCTIONNEMENT AINSI QUE TOUTES LES CONSIGNES

DE SÉCURITÉ. Si vous avez des questions ou si vous ne comprenez pas une instruction, veuillez contacter directement The

Genie Company.

• NE PAS installer l’opérateur sur une porte mal équilibrée. Celle-ci pourrait entraîner de graves blessures. Les réparations

et les réglages des câbles, ensembles de ressort ou tout autre article de quincaillerie doivent être e ectués par un pro-

fessionnel qui se sert d’outils appropriés et qui respecte les instructions.

• Enlever toutes les cordes et désactiver toutes les verrous de la porte avant l’installer l’opérateur.

• Dans la mesure du possible, installer l’ouvre-porte à 2,1 m ou plus au-dessus du sol. Pour les produits dotés d’un cordon

de déclenchement d’urgence, installer le déclenchement d’urgence mais au moins à 1,8 m au-dessus du sol en évitant

tout contact avec les véhicules pour éviter qu’ils ne soient déclenchés accidentellement. NE PAS utiliser d’urgence

cordon de libération pour ouvrir ou fermer la porte.

• NE PAS connecter l’opérateur à la source d’alimentation tant que l’instruction n’est pas donnée.

• Repérer la console murale: A) En vue de la porte. B) À une hauteur minimale de 1,5 m a n que les jeunes enfants ne

puissent pas l’atteindre. C) Loin de toutes pièces mobiles de la porte du garage.

• Placer l’étiquette d’AVERTISSEMENT en cas de coinçage à proximité du bouton mural ou de la console de manière à ce

qu’elle soit bien en évidence. Installer la poignée du cordon de déclenchement d’urgence.

• L’opérateur doit s’inverser lorsque la porte entre en contact avec un objet d’une hauteur de 3,8 cm placé sur le sol, au

centre de l’ouverture de la porte. Ceci équivaut environ à une planche de 5 x 10 cm posée à plat sur le sol.

Safe-T-Beam® (STB) Non-Contact

Reversing System

Puts an invisible beam across the door opening. The

door stops and reverses to the full open position if

anything passes through the beam. LED indicator

lights on the powerhead and on the STBs provide

self-diagnostics if an operational problems exists.

Door Detect™ Monitoring System

Monitors the Safe-T-Beam® system to ensure proper

functionality and will automatically stop and

reverse a closing door if a problem is detected.

Safe-T-Reverse® Contact Reversing System

Automatically stops and reverses a closing door

within two seconds of contact with an object.

Manual Emergency Release

Manually releases door from door opener. Used during a power failure or other emergency to allow manual opening and closing of door.

DO NOT use emergency release cord to pull door

SmartSet

Electronic Programming

Easily adjust the programming to set limits and program new remotes.

Automatic Lighting System (Motion Detection on select models)

Single or Dual Bulb lighting system supplies light for safer evening exits and entries. Turn ON when door is activated and automatically

turns OFF 4 minutes later.

Motion Detection available on select models. Turns lights on when motion is detected in range of opener. Lights will automatically turn

o in 4 minutes.

Intellicode®

An encryption system that enhances the security of the door opener by continuously changing the access code

each time the remote is used. The door opener responds to each new code only once. An access code copied from

a working system and tried again, will not control the door opener.

Wall Console

Operates door opener from inside garage. The wall console has an indicator light, Open/Close, Sure-lock™, and

independent light control buttons.

1.) Indicator Light

Large white button will display Red when wall console is properly wired and Sure-Lock™ is OFF. When Sure-Lock™

is ON, this light is o .

2.) Open/Close Button

Use this button to open or close garage door. When Sure-Lock™ is ON the Open/Close button will CLOSE the door

only.

NOTE: Constant button pressure in the CLOSE mode will override STB fault in the powerhead and close door.

3.) Independent Light Control Button

Use this button to turn the powerhead lights ON. Powerhead lighting will remain ON until this button is pressed

again or a door action has been completed.

4.) Sure-Lock™ Button

When Sure-Lock™ is ON, and the door is closed, the powerhead cannot be activated by the wall console or a

remote.

• Slide switch up to activate Sure-Lock™ (red light goes o ).

• Slide switch down to turn Sure-Lock™ OFF (red light goes on).

Home Link® and Car2U® compatible. See instructions in this manual, refer to the motor vehicle manual or visit

www.GenieCompany.com for instructions.

Factory Programmed Remote Control

For ease and speed of installation, the remote included with this opener comes from the factory, pre-programmed.

No additional steps are required to activate the door using the remote.

Safe-T-Beam® (STB) FUNCTION

1. The Safe-T-Beam® has no e ect on the door during an opening cycle.

2. If the Safe-T-Beam® detects an obstruction when trying to close the

door, it will not allow the door to close.

3. When the garage door is closing, if Safe-T- Beam® is interrupted by

a person or obstacle, the garage door will stop its downward travel

and reverse automatically to its fully opened position.

4. If the Safe-T-Beam® System fails, loses power, or is installed

improperly, press and hold the wall console “open/close” button

until the door reaches its fully closed position. If you release

the “open/close” button on the wall console during the closing

movement, the door will reverse automatically to its fully-opened

position.

SAFETY & STANDARD FEATURES

PRGM

SET

1 & 2

PRGM

SET

NOTE:

Before programming the opener, check to make sure there

are no objects in the garage door opening.

INTRODUCTION

Now that the Genie® garage door opener is installed, follow

the steps in this manual to program the opener so that

the door opens and closes properly and all remote devices

operate correctly. The following steps are a guide to setting

opener so it functions properly.

The following steps list the order of programming the

opener’s functional settings for use.

1. “TRAVEL LIMITS”

2. “FORCE CONTROL”

3. “REMOTE PROGRAMMING”

OVERVIEW OF POWERHEAD CONTROLS

This section describes the programming functions of the

opener. Use the following information to understand the

buttons and LED indicators used to program functions.

Powerhead: There are 3 programming buttons and 2 LED

lights on the powerhead. Each of the buttons are used to

enter and complete the setup programming. The LED lights

indicate status or a function change by illuminating ON, OFF,

or ON FLASHING.

Term De nitions:

Travel Limits Programmable setting to adjust how far door

travels up or down.

Force Control refers to how much power is needed to

move (open/close) a particular door and does NOT require

programming.

Remote Programming synchronizes remote devices

(remote and keypad) with the powerhead.

Speed Control refers to how fast or slow the opener opens

and closes the door. This is factory set and does NOT require

programming. NOT available on all models.

Moves door up or down during

programming and advances

through menus.

Enters into and selects

programming menus.

• Just remember—the pointed end of the button (like an

arrowhead) points in the direction the carriage will move when

that button is pushed.

NOTE:

Each programming step has a 30 second time limit for completion

after the function is initiated. After 30 seconds, two LED’s will illuminate RED

indicating time has expired and the step must be restarted. Restart the step as

many times as necessary to complete the programming.

DOOR

ORIENTATION

Standing under the opener’s powerhead – facing the door – looking

up – this is the view you will see of the programming buttons and

LEDs.

OPENER PROGRAMMING

LED Indicators

Program/Menu

Open Travel

Button

Close Travel

Button

Indicates various programming

modes and trouble codes.

PRGM

SET

There are 4 programs:

1. Door Travel Limits.

- This program is used to set how far the door

travels up and down.

2. Remote Programs (default menu)–only required for

adding remote control transmitters.

- Describes how to program remotes to sync with

additional remote control devices, wall consoles,

keypads and the powerhead.

3. Force Setting Program.

- This program controls the force applied during

the closing and opening of the door. They are

factory set and will rarely require adjustment only

under certain circumstances.

4. Door Speed Program.

- This program does not require manually initiated

changes.

NOTE: The 3 programming buttons are for programming

ONLY. These buttons CANNOT be used to operate the

opener once the required programming section has been

successfully completed.

Motion

Detector

(Select Models)

PRGM

SET

PRGM

SET

PRGM

SET

PRGM

SET

PRGM

SET

WARNING

• Make sure doorway is in full view and clear of obstacles and

people to avoid injury or property damage.

• DO NOT operate this unit from the wall control before LIMITS

are set. Severe damage to the opener could occur.

• The carriage MUST be engaged to Bullet/Screw BEFORE

setting limits. See installation poster or call Customer Service

at 1-800-35-GENIE or visit www.GenieCompany.com.

• DO NOT set limits with Battery Backup attached. AC power

MUST be connected to the opener while setting limits for

proper operation.

AVERTISSEMENT

• S’assurer que le passage de la porte est visible et dégagé, à

savoir sans obstacles ni personne a n d’éviter toute blessure

potentielle ou dommage matériel.

• NE PAS utiliser cette unité avec la console murale avant

d’avoir réglé les LIMITES. L’ouvre-porte pourrait subir de

sérieux dommages.

• La tendeur DOIT être engagée dans le chariot AVANT de

régler les limites. Voir le poster d’installation (si fourni) ou

appelez le service clientèle au 1-800-35-GENIE ou visitez le

site www.GenieCompany.com.

• NE PAS  xer de limites en mode batterie de secours.

L’alimentation CA DOIT être branchée sur l’ouvre-porte,

pendant le réglage des limites, pour assurer un bon

fonctionnement.

1. Press and hold the DOWN arrow button.

• Long LED will light BLUE.

2. Release DOWN arrow button.

• Long LED will  ash BLUE.

3. Press and hold the DOWN arrow button until

door is fully closed.

• Use the UP arrow button if door closes too

far. Use both UP and DOWN buttons to

adjust close travel as necessary.

Door should rest on the  oor until the weather strip

is compressed enough to seal along the width of

the door. Damaged doors or uneven  oors may not

seal properly. Repair these conditions to achieve a

proper seal. DO NOT compress seal so much that the

door will bend or buckle.

4. Press and release the SET/PRGM button

• Both LEDs will  ash BLUE then go out.

The DOWN limit is now programmed.

Steady Blue

HOLD

UNTIL

LED

LIGHTS

Flashing Blue

RELEASE

1-2. Enter Programming Mode

3. Adjust Door Position

Programming DOWN Limit:

NOTE:

Carriage should be locked

to opener. Door should rest somewhere

between full open and closed. Do not start

with door fully open or closed.

4. Lock Programming

Flashing Blue

PRESS

RELEASE

PROGRAMMING DOWN TRAVEL LIMIT

PRGM

SET

PRGM

SET

PRGM

SET

PRGM

SET

PRGM

SET

PROGRAMMING UP TRAVEL LIMIT

Steady Blue

HOLD

UNTIL

LED

LIGHTS

Flashing Blue

RELEASE

1-2. Enter Programming Mode

3. Adjust Door Position

4. Lock Programming

Flashing Blue

PRESS

RELEASE

1. Press and hold the UP arrow button.

• Long LED will light BLUE.

2. Release UP arrow button.

• Round LED will  ash BLUE.

3. Press and hold the UP arrow button until door

is fully open.

• Use the DOWN arrow button if door opens

too far. Use both UP and DOWN buttons to

adjust open travel as necessary.

SECTIONAL DOOR UP LIMIT:

Door should fully open so that door seal is even

with door header. Do not adjust so much that

the door will bend, buckle or stretch door spring

cables backward. Stop carriage short of the opener

powerhead.

ONE-PIECE DOOR UP LIMIT:

Door should fully open so that the door arms will be

in line and push forward and up on the door.

Door damage can result If up limit is set too far

back and door arms are angled downward pushing

against the natural travel direction. Fig. A

4. Press and release the SET/PRGM button

• Both LEDs will  ash BLUE then go out.

The UP limit is now programmed.

Programming UP Limit:

Correct

Angle

Incorrect

Angle

Proper UP limit setting

UP limit set too high

One-Piece Door Limit Setting

Fig. A

Force Control

The force controls are automatically set when the

wall control is used for the  rst time with garage

door opener. The door MUST complete one full cycle, from full

open to full close and then, full close to full open, before the

settings are automatically recorded.

Contact Reverse Test

NOTE:

The limit and Force settings MUST BE COMPLETED

before performing the Contact Reverse Test.

Force Control Adjustments

Force settings are programmed from the factory to

remain within safe parameters. These should not

require adjustments. However, certain circumstances

may require adjustment. See section 4 Maintenance

and Adjustments for detailed instructions pertaining

to the adjustment of force controls.

WARNING

TO AVOID INJURY OR DAMAGE

• NEVER adjust the force settings to adjust for damage,

including an unbalanced door, binding door track or

broken spring.

• Perform a CONTACT REVERSE TEST monthly.

AVERTISSEMENT

Pour éviter les blessures ou des dommages

• NE JAMAIS régler la force pour compenser des dommages,

y compris une porte mal équilibrée, un rail de porte coinçant

ou des ressorts cassés.

• Tous les mois, EFFECTUEZ LE TEST D’INVERSION AU CONTACT.

1. Press and release the wall control button and

allow the garage door to travel and stop at the

DOWN limit.

2. Press and release the wall control button and

allow the garage door to travel and stop at the

UP limit.

1. With the garage door open, lay a 2 X 4 board

 at on the  oor at the center of the door

opening.

2. Close the garage door using the wall control.

• When the door contacts the board, it should

stop and reverse direction within 2 seconds.

Door will move to the full open position.

• The long LED light on the powerhead will begin

to  ash RED with the reversal of the door.

• Remove the 2” x 4” board and operate the

opener with the wall control again. This cycle

will clear the  ashing red LEDs.

Contact Reverse Adjustment

If the door stops before contacting the board or if it

does not reverse direction to fully open after contact

with the board, it may be due to an improperly set

DOWN limit. Verify settings by:

1. Repeat the “Down Travel Limit” section to make

certain the door is closing tight against the  oor.

2. Repeat the “Force Control” section on the left to

set force limits.

3. Repeat the “Contact Reverse Test” above.

Repeat this process as needed until the door passes

the Contact Reverse Test. For further help, refer to

the “Maintenance and Adjustment” section/Regular

Maintenance.

PROGRAMMING FORCE AND CONTACT REVERSE

PRGM

SET

PRGM

SET

NOTE:

The following instructions are for remote control transmitters

purchased separately in addition to those provided with this opener,

but can also be used if any remote(s) may require re-programming.

NOTE:

Each programming step has a 30 second time limit for

completion after the function is initiated. After 30 seconds, two

LED’s will illuminate RED indicating time has expired and the step

must be re-started. Restart the step as many times as necessary to

complete the programming.

NOTE:

Do not hold remote too close to the powerhead when

programming remote buttons.

NOTE:

Each button on each remote must be programmed

separately, following these steps.

1. Remove the battery’s protective  lm from the

remote by pulling straight out.

2. Press and hold the SET/PRGM button on the

opener for two seconds.

• The ROUND LED will turn BLUE.

• The LONG LED will then  ash PURPLE.

3. Stand at least 5 feet away from opener and

slowly press and release the desired button on

the remote two times.

• Both opener LEDs will  ash and turn o

indicating the remote has been programmed.

4. Press the desired remote button again.

• The opener should run.

To program the same remote for other garage door

openers, repeat the steps above using one of the other

remaining remote buttons.

REPEAT STEPS 1 TO 4 FOR EACH OPENER AND

REMOTE

NOTE:

It is possible to press the remote button too quickly

or lightly. If the LEDs do not go o , press the remote button

several more times to achieve con rmation.

BASIC PROGRAMMING IS COMPLETE AND YOUR GARAGE

DOOR OPENER IS READY TO USE.

See page 19 to erase remote devices from memory.

Flashing

2. Enter Programming Mode

4. Test Remote

1. Activate Remote(s)

Solid Blue

PRESS for 2

SECONDS

& RELEASE

Flashing Purple

3. Press Remote Button Twice

PROGRAMMING ADDITIONAL REMOTE CONTROLS

THE REMOTE CONTROLS INCLUDED WITH

THIS OPENER HAVE BEEN

PROGRAMMED AT THE FACTORY FOR YOUR

CONVENIENCE.

PRGM

SET

WARNING

To reduce the risk of severe injury or death,

read and follow all instructions.

1. NEVER let children operate or play with the door controls.

2. Keep remote away from children.

3. ALWAYS keep the moving door in sight and away from people and objects until door is completely closed. NO ONE

SHOULD CROSS THE PATH OF THE MOVING DOOR.

4. NEVER GO UNDER A STOPPED, PARTIALLY OPEN DOOR.

5. Test opener monthly. The door MUST reverse on contact with a 1-1/2” high object (or 2” x 4” board laid  at) at the center

of the doorway on the  oor. After adjusting either the force or limit of travel, retest door opener. Failure to adjust the

opener properly may cause severe injury or death.

6. When possible, use emergency release only when door is closed. Use caution when using this release with the door

open. Weak or broken springs are capable of increasing the rate of door closing and increasing the risk of severe injury or

death.

7. KEEP DOORS PROPERLY BALANCED. See your garage door Owner’s Manual. An improperly balanced door increases the

risk of severe injury or death. Have a trained door system technician make repairs to cables, spring assemblies, and other

hardware.

SAVE THESE INSTRUCTIONS

WARNING

• Garage door hardware (springs, cables, brackets, pulleys, etc.) are under

extreme pressure and tension.

• DO NOT attempt to repair or adjust door springs or any hardware, and

DO NOT OPERATE garage door automatically or manually if door is

improperly balanced or springs are broken.

• CONTACT A TRAINED DOOR SYSTEM TECHNICIAN.

IMPORTANT SAFETY INSTRUCTIONS

AVERTISSEMENT

• La quincaillerie de la porte de garage (ressorts, câbles, supports, poulies,

etc.) sont sous des pressions et des tensions extrêmes.

• NE PAS réparer ni régler les ressorts de la porte ou toute autre pièce

de quincaillerie et NE PAS ACTIONNER la porte manuellement ou

automatiquement si elle n’est pas correctement équilibrée ou si des ressorts

sont cassés.

• CONTACTEZ UN TECHNICIEN SPÉCIALISÉ EN SYSTÈME DE PORTES

WARNING

Opener is equipped with grounded electrical plug for your protection, and

only  ts grounded electrical outlets. DO NOT alter plug in any way! If your

have no grounded outlets, have one installed by a licensed electrician.

Opener must be properly grounded to prevent personal injury and equipment

damage. NEVER USE AN EXTENSION CORD! Check local building codes for

any requirement that you must have a permanent hard-wired connection.

Permanent hard-wired connections must be performed by a licensed electrician

using proper tools and instructions.

AVERTISSEMENT

L’opérateur, qui est équipé d’une prise électrique mise à la terre pour votre

protection est compatible uniquement avec des prises électriques mises à

la terre. NE PAS modi er la  che dune quelconque manière. Si vous n’avez pas

de prises mises à la terre, faites-en installer par un électricien agréé. L’opérateur

doit être correctement mis à la terre pour éviter les blessures corporelles et des

dommages matériels. NE JAMAIS UTILISER DE RALLONGE! Véri ez les codes

locaux des bâtiments pour connexions câblées permanente. Les connexions

câblées permanentes doivent être e ectuées par un électricien agréé qui se

servira d’outils appropriés et respectera les consignes.

AVERTISSEMENT

Pour réduire le risque de blessures graves

voire mortelles, lire et comprendre toutes les

instructions.

1. NE JAMAIS permettre aux enfants d’actionner ou de jouer avec les commandes de la porte.

2. Tenir les télécommandes hors de la portée des enfants.

3. TOUJOURS garder en vue la porte en mouvement et tenir à l’écart toute personne ou objet jusqu’à ce que la porte soit

totalement fermée. PERSONNE NE DOIT TRAVERSER LA TRAJECTOIRE D’UNE PORTE EN MOUVEMENT.

4. NE JAMAIS PASSER SOUS UNE PORTE À L’ARRÊT PARTIELLEMENT OUVERTE.

5. Tester l’ouvre-porte une fois par mois. La porte de garage DOIT inverser sa course au contact d’un objet de 4 cm (planche

de 5 sur 10 cm) posé à plat sur le sol au centre de l’ouverture de la porte. Après avoir réglé la force ou la limite de la

course, retenter l’ouvre-porte de garage. Un mauvais réglage de l’ouvre-porte peut entraîner des blessures graves voire

mortelles

6. Utiliser, dans la mesure du possible le déclenchement d’urgence uniquement lorsque la porte est fermée. Utiliser le

déclenchement d’urgence avec prudence lorsque la porte est ouverte. Des ressorts faibles ou brisés peuvent faire

descendre la porte rapidement ce qui peut entraîner des blessures graves voire mortelles.

7. VEILLER À CE QUE LA PORTE SOIT CORRECTEMENT ÉQUILIBRÉE. Consulter le manuel du propriétaire de la porte de

garage. Une porte déséquilibrée pourrait entraîner de graves blessures voire mortelles. Demander à un technicien

spécialisé en système de portes de se charger des réparations des câbles, des ressorts et de toute autre quincaillerie.

CONSERVER CES INSTRUCTIONS

IMPORTANTES CONSIGNES DE SÉCURITÉ

L’utilisation d’une autre commande murale pourrait produire des résultats inattendus de la

porte ainsi que le dysfonctionnement de l’éclairage. Localisez la console murale en vue de

la porte et su samment loin de la porte pour éviter tout contact pendant l’utilisation de la

console. La commande doit être à une hauteur minimale de 1,5 m au-dessus du sol a n que les

jeunes enfants ne puissent pas l’atteindre.

VERTISSEMENT

WARNING

Use of any other wall control can cause unexpected operation of the door

and loss of lighting feature. Locate wall console within sight of the door but

far enough from door to prevent contacting it while operating the console.

Control must be at least 5 feet above the  oor to prevent small children from

operating it.

MAINTENANCE & ADJUSTMENTS

For help, call customer service at 1-800-35-GENIE or visit www.GenieCompany.com

Regular Maintenance

Basic monthly maintenance tasks include:

• Contact Reverse Test

• Lubricate door hardware

• Safe-T-Beam® System check

• Door balance

• Remote Battery Replacement (As needed)

• Light Bulb Replacement (As needed)

A. Contact Reverse Test

See page 10.

B. Lubricate Door Hardware

Inspect door rollers and hinges and lubricate as needed using a

light weight general purpose grease.

C. Safe-T-Beam

(STB) System Check

Check that both the RED and GREEN LEDs are ON steady. This indicates

the system is working properly. If both LEDs are not ON steady, check

the appropriate items below:

• STB red LED  ashes.

– Check for obstruction.

– Check alignment. (See page 16)

– Verify wire routing from STBs to STB connection in powerhead

– Check for signal interference from another Safe-T-Beam® unit

(for multiple door installations).

• No STB red or green LED displayed.

– Check wiring and wire connections

If system appears to be working properly, perform check as follows:

1. Start the door closing.

2. Pass an object through the beam. The door should stop and

reverse to the fully open position.

– Door should remain stationary or move very slowly.

– If door moves quickly, CONTACT A TRAINED DOOR SYSTEM

TECHNICIAN to have your door springs serviced.

• Close the door.

• Place the carriage in the “engage” position.

• Operate door using remote or wall control. The carriage will

reattach itself to the drive chain/belt.

Remote Battery Replacement

(3-button)

Replace remote battery with a CR2032 coin cell battery.

1. Open remote case using a washer or coin that  ts into the slot on the top of the remote.

2. Replace battery.

Be sure positive side (+) is UP.

3. Align components and snap case closed.

• Raise and lower the door

manually — it should move

freely and smoothly.

• Raise door manually about

3’ to 4’ feet and let go.

Perform the check as follows:

• With the door closed, pull manual emergency release handle

DOWN and away from door and let go to disengage the carriage

from the drive chain/belt or screw).

D. Door Balance (Spring Tension)

E. Remote Battery Replacement (As needed)

DO NOT use release cord to pull door.

Screw Drive Chain/Belt Drive

Disengage the carriage by pulling

the release handle straight down,

and then releasing

Disengage the carriage by pulling

the release handle down, toward

the door and then releasing

Changing Light Bulbs

1. Disconnect power to door opener.

Open powerhead light cover(s) by pressing in on upper locking tab and swing down.

• Replace old light bulb(s) with new.

• Use 100 Watt MAX* incandescent bulbs or the CFL or LED equivalent.

*NOTE: 2562 and 2568 models use 60 Watt Max bulbs.

• Close powerhead light cover(s).

2. Reconnect power to door opener and close lens cover.

• Test light operation.

NOTE: Use of LED bulbs may reduce the range of your remote controls.

Visit www.GenieCompany.com for more information on speci c LED bulbs produced for garage door openers.

F. Light Bulb Replacement

WARNING

• Use extreme caution when working from a ladder or step

stool or serious injury can occur.

• When replacing light cover, make sure wires are not pinched

or near moving parts.

• Use only properly rated incandescent, LED or CFL light bulbs.

• DO NOT use bulbs with a rating greater than 100 Watts*.

• Use A19 size light bulbs. DO NOT use bulbs having a short

neck.

AVERTISSEMENT

• Faire particulièrement attention lors de travaux e ectués

depuis une échelle ou en escabeau.

• En referment le couvercle de l’éclairage, s’assurer que les  ls

ne sont ni coincés ni près des pièces mobiles.

• Utilisez uniquement incandescence correctement classé, LED

ou des ampoules  uocompactes.

• NE PAS utiliser des ampoules avec une note supérieure à 100

Watts*

• Utilisez A19 ampoules de taille. NE PAS utiliser des ampoules

ayant un cou court.

MAINTENANCE & ADJUSTMENTS

Speed Adjustment

Speed Settings (DC Models only)

Speed settings are pre-programmed at the factory for the

maximum speed. Speed settings should not need adjustment

with this unit. However, travel speed for the opener can

be adjusted to a slower speed in both the Open and Close

directions, to minimize wear on heavier sectional doors.

There are three speed settings available for sectional doors.

Please note that speed may be a ected by door weight and

balance, along with condition of door components and tracks.

G. Adjustment Guides

MAINTENANCE & ADJUSTMENTS

G. Adjustment Guides

Force Settings

Force settings are pre-programmed at the factory and applied

during the Open/Closed Limit settings steps. For normal use, these

settings should not need adjustments with this unit.

H. Resetting Travel Limits

See pages 8-9 to reset travel limits. Force setting and contact reverse test must be performed in the event of a travel limit change.

AVERTISSEMENT

Pour éviter les blessures ou des dommages

• NE JAMAIS régler la force pour compenser des dommages,

y compris une porte mal équilibrée, un rail de porte coinçant

ou des ressorts cassés.

• Tous les mois, EFFECTUEZ LE TEST D’INVERSION AU CONTACT.

Voir page 10.

WARNING

TO AVOID INJURY OR DAMAGE

• NEVER adjust the force settings to adjust for damage,

including an unbalanced door, binding door track or

broken spring.

• Perform a CONTACT REVERSE TEST monthly. See page 10.

Conditions possibly requiring adjustments are:

1. Doors with very sti weather seals.

2. Doors that start down, STOP, and reverse before closing.

3. Doors that start up, but STOP before they completely open.

Press and hold both up and

down arrow buttons until

round LED turns RED, release

buttons. Round BLUE LED will

 ash 3 times.

LEDs will now display current UP force setting (See chart).

Press either arrow button until

desired UP force setting is

reached.

See Chart

Once setting is chosen, press

and release. This will lock the

UP force setting.

LEDs will now show current DOWN force setting. (See Chart).

Press either arrow button until

desired DOWN force setting is

reached.

See Chart

Once setting is chosen, press

and release. This will lock the

DOWN force setting.

The LEDs will now turn BLUE then o . This con rms

that both force settings have been set and unit is

ready for normal operation.

Repeat “Learn Force Limits and Contact Reverse Test” page 10.

OFF

BLUE

OFF

Flashes

3 Times

OFF

RED

BLUE

PRGM

SET

PRGM

SET

LOCATING SAFE-T-BEAM® PAIRS

Transmitter (RED LED) and Receiver (GREEN LED)

Single Garage Door

• Determine which side of the garage receives direct sunlight.

• Position the Transmitter (Red LED) on the direct sunlight side.

Multiple Garage Doors

•

NEVER position Safe-T-Beam® modules where signals will cross.

• Place the Transmitter (Red LED) Safe-T-Beams on adjacent doors

facing in opposite directions.

NOTE:

Direct sunlight creates interference with Safe-T-Beam

Receiver (Green LED). STB modules CAN be positioned further

away from the door opening if necessary to avoid sunlight

but no further o the wall to maintain alignment with the

Transmitter (Red LED) module.

WARNING

AVERTISSEMENT

CHOC ÉLECTRIQUE

OUVERTURE DE COUVERTURE

PEUT PROVOQUER

CHOC ÉLECTRIQUE.

Coupez l'alimentation du

premier match avant de retirer

le couvercle.

MAINTENANCE & ADJUSTMENTS

WIRE DIAGRAM

NOTE: Only use Safe-T-Beams® that are included with this opener. DO NOT use other

brands or types of photocells on this opener.

Visit www.genicompany.com or call Customer Service at 1-800-35-GENIE.

Need help or have questions? DO NOT RETURN to the store.

PROBLEM: WHAT TO DO:

Opener does NOT

operate when wall

control is pressed.

• Turn Sure-Lock™ OFF See page 6.

• Check power source.

– Plug a lamp into outlet used for powerhead. If lamp works, power source is OK.

– If not, check fuse or circuit breaker.

• If power is OK,

– Check connections at powerhead terminals and at wall console.

• Check for reversed, broken or cut wires. Staples can cut insulation and short wires. Repair or replace.

Opener runs, but

door does not

move.

• Make sure carriage is engaged with chain/belt bullet or screw. Refer to installation

poster or download poster from www.GenieCompany.com

• Check to make sure chain/belt is not broken or o its pulley.

Opener works from

wall control, but

NOT from remote.

• Check all remotes.

• Replace remote battery. See page 13.

• Program remotes to powerhead. See page 11.

Remote has less

than 25 feet

operating range or

no operation.

• Relocate remote inside car and /or point remote at garage door.

• Replace battery. See page 13.

• Reposition door opener antenna.

• Eliminate possible competing signals (radio, etc.).

• LED bulbs may be interfering with remote signal. See page 14.

Door starts down,

then STOPS and

goes back up.

Safe-T-Beam

System malfunction.

• If a NEW installation, check Door Arm position. Refer to Installation poster or download poster

from www.GenieCompany.com.

• If NEW Installation, make sure ONLY the Safe-T-Beams® that came with this opener are installed.

• Check if limits are properly set. See pages 8-9. Adjust limits as needed.

• Check if Safe-T- Beam® red LED is  ashing. See page 16, Safe-T-Beam® system check.

• Check Safe-T-Beam® system for beam obstruction or misalignment of lenses. See page 16, Safe-T-Beam®system.

• Check garage door for binding.

• If an operational problem exists, and opener will not close, the opener can be forced to close as follows: Press

and hold the wall control button until door is completely closed.

• Check for interference from adjacent Safe-T-Beam® units. See page 16.

• Contact Genie at 1-800-35-GENIE.

Door starts down,

then STOPS before

it is closed.

OR Door will only

open.

• Check Safe-T- Beam®wire connection at powerhead and at STBs. See page 16, Safe-T-Beam® system check.

• Check if limits are properly set. See pages 8-9. Adjust limits as needed.

• Check CONTACT REVERSE. See page 10.

• Check garage door for binding. See maintenance and adjustment. Page 13.

• Check closing “FORCE” control. See page 10, or Force settings. Page 15.

Door starts up, but

STOPS before it is

completely open.

• Check if limits are properly set. See pages 8-9. Adjust limits as needed.

• Be sure door, opener, springs are in good repair, properly lubricated and balanced.

• Check closing/opening “FORCE” control. See page 10, or Force settings Page 15.

• If you suspect a problem with the garage door hardware or springs, visit www.GenieCompany.com

and use the “dealer locater” to hire a local door service professional.

NEVER try to repair door hardware or springs yourself.

Door will only run

closed.

• Turn Sure-Lock™ OFF See page 6.

• Check if limits are properly set. See pages 8-9.

• Check door balance, condition, and door spring.

• Check opening “FORCE” control. See page 10, or Force settings. Page 15.

• If you suspect a problem with the garage door hardware or springs, visit www.GenieCompany.com

and use the “dealer locater” to hire a local door service professional.

NEVER try to repair door hardware or springs yourself.

Door opener starts

for no reason.

• Button stuck on wall control or remote.

• Was remote lost or stolen? Erase all remotes from powerhead memory and program new remotes. See page 19.

Noisy operation.

• Be sure all door fasteners are tight.

• Be sure garage door is in good repair, properly lubricated and balanced.

• Be sure opener is in good repair.

Door opener runs

slowly.

• Check operating condition of door. Door may need professional repair/adjustment.

• Opener will run slower on one-piece doors. This is normal operation.

TROUBLESHOOTING

POWERHEAD LEDS

Powerhead LED

Possible Problem

Solution

Round LED Long LED

OFF OFF

Normal operation. None required.

No response from unit.

Check power supply.

Contact a trained door system professional.

ON/RED/

STEADY

ON/RED/

STEADY

Limits NOT set properly. Re-program limits, see pages 8-9.

ON/RED/

FLASHING

ON/RED/

FLASHING

Program error. Unplug unit, wait 5 seconds, plug in.

Component failure. Contact a trained door system technician.

ON/BLUE/

FLASHING

OFF Remote NOT programmed. Program remote, see page 11.

ON/PURPLE/

FLASHING

OFF Remote NOT programmed. Program remote, see page 11.

ON/RED/

FLASHING

OFF

Safe-T-Beam® physical obstruction. Remote obstruction, recheck unit.

Safe-T-Beam® signal interference.

Check alignment of Safe-T-Beam® pair and

nearest other Safe-T-Beam® pair, see page 16.

OFF

ON/RED/

FLASHING

Door contact in UP or DOWN travel. Remove obstruction.

Door component failure detected.

Check door spring, track, rollers, hinges and

 xtures.

OFF

ON/RED/

STEADY

Thermal cutout.

DO NOT unplug unit.

Wait until LED clears before operating.

ON/PURPLE/

STEADY

ON/PURPLE/

STEADY

Component error. Contact a trained door system technician.

OFF

ON/BLUE/

FLASHING

Door will not open.

Check Sure-Lock™. Sure-Lock™ should be OFF for

normal operation (see page 6).

ON/PURPLE/

FLASHING

ON/PURPLE/

FLASHING

Radio receiver error.

Unplug the unit. Wait 5 seconds and plug the unit

back in. If problems persist, contact a trained door

system technician.

PRGM

SET

PRGM

SET

PRGM

SET

PRGM

SET

CLEARING MEMORY OF REMOTES

NOTE:

Clearing memory of remotes from the powerhead

will clear ALL programmed remotes, wireless keypads and

vehicle transmitters. The opener will no longer recognize

any signal from any remote device, including a missing

remote device.

All remaining (or recovered) remotes, vehicles and

wireless keypads MUST be reprogrammed.

NOTE:

The garage door opener will operate normally

using the wall console.

1. Press and hold the SET/PRGM button on the

opener for two seconds.

• The ROUND LED will turn BLUE.

• The LONG LED will then  ash PURPLE.

2. Press and hold the UP & DOWN buttons at the

same time until both LEDs turn o .

• Both opener LEDs will  ash and turn o

indicating that all remotes have been erased.

3. Press any remote button.

• The opener should NOT run.

To deprogram the same remote for other garage door

openers, repeat the steps above using one of the other

remaining remote buttons.

1. Enter Programming Mode

Solid Blue

PRESS 2

SECONDS

& RELEASE

Flashing Purple

2. Press and Hold + (UP) & - (DOWN) Buttons

3. Test Remote

Release when LEDs turn o

OPTIONAL PROGRAMMING & ACCESSORIES

Flashing

Blue

OFF

PRGM

SET

B. Press the chosen HomeLink button for two seconds and release. Press

that same button again for two seconds and release. The long LED

will  ash blue and then turn o .

C. Press the HomeLink button a few more times until door moves.

NOTE:

For additional instructions, see the motor vehicle manual,

www.homelink.com or visit www.GenieCompany.com

Step 1 Clear HomeLink

Clear HomeLink by pressing and

holding down the  rst and third buttons

until the indicator on the HomeLink blinks

slow and then fast for 20 seconds; then

release both buttons.

NOTE: Clearing the HomeLink will remove all previously

programmed garage door openers.

Step 2 Train HomeLink to the Genie Remote

Choose the button on the HomeLink that will be used to open the door.

NOTE:

Hold the Genie Remote two inches from the HomeLink button.

Hold down the Genie remote button. While holding, press and hold the

chosen HomeLink button.

Hold down both buttons until the indicator on the HomeLink blinks slow

then fast. Once it blinks, release both buttons.

Step 3 Program HomeLink to the Genie Opener

Press PROGRAM SET button two seconds until the round LED turns

blue, then release. The long purple LED will blink.

Programming HomeLink® System Programming Car2U

System

Step 1 Clear Car2U to default settings

The default setting for the Car2U system is:

• Button 1 = Genie® Manufactured Openers

• Button 2 = LiftMaster® Manufactured Openers

• Button 3 = Wayne Dalton® Manufactured Openers

A. Press and hold buttons 1 and 3 for 20 seconds or until all three LEDs

begin to  ash.

B. Release both buttons. The Car2U system is now set to the Factory

Default settings

NOTE:

Clearing the Car2U remote will remove all previously programmed

garage door openers.

Step 2 Program Car2U to the Genie Opener

Press PROGRAM SET button two seconds until the round LED turns

blue, then release. The long purple LED will blink.

B. Press the designated Genie Car2U button for two seconds and release.

Press that same button again for two seconds and release. The long LED

will  ash blue and then turn o .

C. Press the Car2U button a few times more until door moves.

Step 3 Changing Factory Default Button for a Genie Opener

A. Press and hold buttons 1 & 3 for ONE SECOND and release—all three

LEDs will light solid red.

B. Press and hold the button (2 or 3) to change it to Genie—the

corresponding LED will  ash. While continuing to hold that button,

press and release button 1. Press and release button 1 again.

C. Release the button being held in step B and wait for the LED to stop

 ashing. This button is now set for Genie. Repeat Step 2 for second

Genie Opener.

NOTE:

For additional instructions see the motor vehicle manual,

learcar2u.com or visit www.GenieCompany.com

VEHICLE PROGRAMMING

PRGM

SET

La page charge ...

Genie 3062 Maintenance Manual

Marque: Genie

Modèle: 3062

Catégorie: Porte de garage

Taper: Maintenance Manual

Télécharger le PDF

rapport

dans d''autres langues

English: Genie 3062

Genie 3062 Maintenance Manual

Genie 3062 Maintenance Manual

dans d''autres langues

Documents connexes

Autres documents