Leica Zeno FLX100 Smart Antenna
Quick Guide
Version 1.0
English
1 Important Information about your Instrument
Read and follow the User Manual from the myWorld web page before using the
product.
myWorld@Leica Geosystems https://myworld.leica-geosystems.com
Keep for future reference!
•Measuring raw data and computing coordinates using carrier phase and
code signal from GNSS satellites (GNSS systems).
•Computing with software
•Recording measurements
•Recording GNSS and point related data
•Carrying out measurement tasks using various GNSS measuring techniques
•Data communication with external appliances
The product must not be disposed with household waste.
☞
Intended use
8 Important Information about your Instrument
en
For the AC/DC power supply and the battery charger:
WARNING
Unauthorised opening of the product
Either of the following actions may cause you to receive an electric shock:
•Touching live components
•Using the product after incorrect attempts were made to carry out repairs.
Precautions:
▶Do not open the product!
▶Only Leica Geosystems authorised service centres are entitled to repair
these products.
9 Important Information about your Instrument
en
•FCC Part 15 (applicable in US)
•Hereby, Leica Geosystems AG declares that the radio equipment type
FLX100 smart antenna is in compliance with Directive 2014/53/EU and
other applicable European Directives.
The full text of the EU declaration of conformity is available at the fol-
lowing Internet address: http://www.leica-geosystems.com/ce.
Class 1 equipment according to European Directive 2014/53/EU
(RED) can be placed on the market and be put into service without
restrictions in any EEA member state.
•The conformity for countries with other national regulations not covered
by the FCC part 15 or European Directive 2014/53/EU has to be approved
prior to use and operation.
•Bluetooth® is a registered trademark of Bluetooth SIG, Inc.
All other trademarks are the property of their respective owners.
Conformity to
national
regulations
Trademarks
10 Important Information about your Instrument
en
1.1 Instrument Components
a
b
c
d
f
21306_002
e
a Connection LED
b Data link LED
c Satellite LED
d Battery LED indicator
e Power button
f USB type-C port
a
21307_001
a Holes for the screws
to x the pole
adapter
Description
Description
11 Important Information about your Instrument
en
2 Technical Data
Internal battery 3.8 V, 6120 mAh
Type-C charging, support 1.44 A fast charge
Input voltage 5 V DC/2 A
Power consumption 1.8 W
Working time Up to 10 hours (post processing)
Up to 8 hours (RTK with GSM)
Charge time Typically 6 hours
Type Operating temperature [°C] Storage temperature [°C]
Instrument −30 to +65 −40 to +80
External inuences Protection
Water, dust and sand IP67
Humidity Up to 100% (non-condensing)
Power
Environmental
specications
12 Technical Data
en
External inuences Protection
Shock resistance Designed to endure to a 2 m pole drop and
1.2 m free drop on concrete oor with no
damage
2.1 Care and Transport
Carry the product in its original container to protect the product against shock
and vibration.
Care and transport
13 Technical Data
en
3 Operation
The battery must be charged before using it for the rst time.
Turn on:
Press and hold the power button until the battery LED goes green and the device
sounds a beep.
Turn off:
Press and hold the power button until the battery LED goes out and the device
sounds a beep.
a
21304_002
b
a Power on/off button
b Battery LED indicator
3.1 Connect the Handheld to Receiver by Bluetooth
Follow these steps to connect the handheld to the instrument by Bluetooth.
1. Open the Bluetooth settings on your device.
☞
Turning on/off the
instrument
Step-by-step
14 Operation
en
2. Search for your FLX100 smart antenna with its serial number.
3. Find target FLX100 smart antenna serial number.
4. Push Connect.
3.2 Connect the Handheld to the Pole
Follow these steps to connect the handheld to the pole.
21376_001
21
1. Use a slot screwdriver to x the pole adapter with both screws to
the FLX100 smart antenna.
☞Make sure to x the adapter in the correct orienta-
tion.
2. Screw the pole clockwise into the adapter.
Step-by-step
15 Operation
en
922524-1.0.0en
Original text (922524-1.0.0en)
Printed in Switzerland
© 2020 Leica Geosystems AG, Heerbrugg, Switzerland
www.leica-geosystems.com
FCC warning statements:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved
by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirement.
IC warning statements:
-English Warning Statement:
“This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device."
The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).
-French Warning Statement:
“Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d'en compromettre le fonctionnement."
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
This device meets the IC radiation exposure limits for uncontrolled environments and
rss-102 of IC radio frequency (RF) exposure rules. The device has a very low RF
energy level and has been evaluated (SAR) tested within the allowable range.
Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées
pour un environnement non contrôlé et respecte les règles d’exposition aux
fréquences radioélectriques (RF) CNR-102 de l’IC. Le dispositif fournit une très
faible énergie RF et le débit d 'absorption spécifique (DAS) a été évalué dans les
limites autorisées.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
dans d''autres langues
- English: Leica FLX100 User guide
Documents connexes
-
Leica GEOACE RTK BASE STATION Le manuel du propriétaire
-
Leica MOJORTK Le manuel du propriétaire
-
-
-
-
-
-
-
-