Huawei WiFi Q2 Pro Guide de démarrage rapide

Quick Start Guide

Contents

Quick Start Guide

......................................................................

1

Guide de démarrage rapide

.....................................................

15

Kurzanleitung

...........................................................................

30

Guida di avvio rapido

...............................................................

44

Snelstartgids

............................................................................

58

Guia de início rápido

................................................................

73

Guía de inicio rápido

................................................................

88

1

Quick Start Guide

After conguring the base router, simply plug the satellite router into

a power supply to access the Internet.

H button

Power port

RESET button

(EU version)

LAN port: Connect

to a wired Internet

device, such as a

computer.

WAN port: Connect to optical

modems, broadband modems, etc.

LAN port: Connect to a wired

Internet device, such as a computer.

Indicator

Getting Started

Base router

Satellite router

(UK version)

RESET button

LAN port: Connect

to a wired Internet

device, such as a

computer.

2

Step 2: Connect the cables

Take out the base router, then connect the Ethernet cable and power supply.

Optical/broadband/cable modem

Wall port

Wall socket

HUAWEI WiFi Q2 Pro

Insert the cable to the

WAN port on the router

Using a power

strip is not

recommended

Internet

Or

from your broadband provider

Do not bundle the Ethernet cable and the power cable together. Otherwise, the router's signal

may be affected.

Search for “HUAWEI SmartHome” in an app store, or scan the QR code below with

your phone to download and install the HUAWEI SmartHome app.

Step 1: Install the HUAWEI SmartHome app

If the HUAWEI SmartHome app is already installed on your phone, make sure you have the

latest version of the app.

3

Step 3: Set up the base router

Method 1: Congure the router on the SmartHome app

Connect your mobile phone to the router's Wi-Fi

®

(no password). Check for the

Wi-Fi name on the bottom of the router.

1

WiFi

Connected

Open the HUAWEI SmartHome app.

After the app has detected the router,

touch

CONFIGURE

.

Touch

SET UP

.

If the prompt box does not appear, touch

+

.

2 3

CONFIGURE

LATER

SET UP

4

If your Internet connection does not require an account and password:

Please skip to the next step.

If you remember your broadband account and password:

Enter your broadband account and password.

If you have forgotten your broadband account and password:

Obtain the broadband account and password from the old router. Take

another Ethernet cable and connect the WAN port of the old router to the

LAN port of the new router.

Or contact your carrier and obtain a broadband account and password.

Step 1

VLAN

Broadband account

Broadband password

CONNECT

RETRIEVE

Step 1 Step 1

VLAN

Broadband account

Retrieving…

Broadband password

Broadband account

Broadband password

CONNECT

RETRIEVE

If you need to congure VLAN on your network, contact

your broadband carrier to conrm the VLAN parameters,

and enable the VLAN switch on the screen.

If you need to congure VLAN on your network, contact your broadband carrier to

conrm the VLAN parameters, and enable the VLAN switch on the screen.

5

Step 2

Wi-Fi name

Wi-Fi password

Use Wi-Fi password

as router password

Prioritize 5 GHz

Network settings

Enable

Prioritize 5 GHz

: The

2.4 GHz and 5 GHz Wi-Fi

names are the same. You will

automatically connect to the

faster Wi-Fi network.

Reconnect to the router's Wi-Fi to access

the Internet.

If the router cannot be congured on the

app, congure the router on the web-

based management page by following the

instructions in Method 2.

Set a new Wi-Fi name, Wi-Fi password, and management password for the

new router. You can use the Wi-Fi password as the router's management

password.

5

Method 2: Congure the router on the web-based management page

Connect your mobile phone to the router's Wi-Fi (no password). Check for the

Wi-Fi name on the bottom of the router.

1

WiFi

Connected

6

Open the browser and you will be automatically redirected to the web-

based management page (if the page is not displayed automatically, enter

"192.168.3.1" in the browser address bar). Follow the onscreen instructions to

congure the router.

2

Let's Start

After conguring the base router, plug the satellite router into the room where Wi-

Fi coverage is needed. Wait for approximately two minutes until the indicator turns

steady blue to access the Internet.

Step 4: Connect the satellite router to the power supply

Wall socket

Using a power strip is not recommended

Some power strips have EMI lters that may

prevent the satellite router from accessing the

Internet.

7

The Wi-Fi name and password of the satellite router are the same as those of the base

router. As you move around your home, you will automatically connect to the router with the

best signal.

If the indicator is steady red, it indicates that the satellite router is unable to access the

Internet. In this case, please refer to the "Indicator - Satellite router - Steady red" section

below for more information.

If you are still not getting Wi-Fi signals in certain parts of your home, you can purchase

satellite routers separately to expand your Wi-Fi coverage.

Satellite routers expand the Wi-Fi coverage of the base router to other rooms through wired

connections. Chargers, hair dryers, vacuum cleaners, electric drills, and LED or any other

lights with induction switches may all interfere with the signals of your satellite routers.

Indicator

Steady blue: connected to the Internet.

Steady red: not connected to the Internet.

Ensure that the Ethernet cable is not loose and connected correctly.

Contact your carrier to check for any network failure.

Base router

Flashing: The router has detected a pairable device.

When other HUAWEI routers (with H or Hi button) are detected, the indicator will

ash. When this happens, press the router's H button. The indicator should ash

quickly, indicating that the pairable device is connecting to the router's Wi-Fi. The

connection process is complete when the indicator stops ashing.

If you touch the H button accidentally, wait for approximately two minutes and the indicator

will be reset automatically.

The H button also features WPS functionality.

8

Steady blue: connected to the Internet.

Steady red: not connected to the Internet.

Ensure that the power cable and Ethernet cable of the base router are not

bundled together.

Ensure that the base and satellite routers are plugged into wall sockets.

Plug the satellite router into a different wall socket and try again.

Ensure that the satellite router is connected to the base router's network.

Restore the satellite router to its factory settings and try again.

Satellite router

Frequently Asked Questions (FAQs)

Why does my router emit a beeping noise?

1.

2.

What should I do if after conguring my HUAWEI WiFi Q2 Pro, my mobile phone

automatically connects to the Wi-Fi network of the previously connected optical/

broadband/cable modem instead of the Wi-Fi network of my HUAWEI WiFi Q2

Pro?

Your router will emit a beeping noise when detecting the power line environment in

your home. This is normal and does not indicate an issue with your device.

It is recommended that you disable the Wi-Fi network of your previous optical/

broadband/cable modem to reduce potential signal interference with your

HUAWEI WiFi Q2 Pro.

9

3.

What should I do if HUAWEI WiFi Q2 Pro is not recognized on the HUAWEI

SmartHome app?

Ensure that your HUAWEI SmartHome app is up to date.

Connect your phone to the base router's network.

Ensure that the base and satellite routers are new or have been restored to

factory settings.

Connect the base and satellite routers to power supplies, then wait for a few

moments until the startup processes are complete and try again.

It is recommended that there are no more than two walls in between your

phone and base router.

4.

Can the HUAWEI WiFi Q2 Pro be used with a HUAWEI WiFi Q2?

Please do not use your HUAWEI WiFi Q2 Pro with a HUAWEI WiFi Q2 as this

will decrease the performance of your router.

5.

What should I do if I encounter any of the following issues during the

conguration of the router?

If your phone cannot nd the router's Wi-Fi, ensure that the router is connected

to a power source. Wait until the router completes the startup process. Then try

searching the router's Wi-Fi again on your phone.

If the page prompts "Internet cable not detected", ensure that the Ethernet

cables are well connected and in good condition.

If the page prompts "Incorrect username or password", please re-enter your

broadband account and password. If the problem persists, your carrier may

have bound the MAC address of the old router, resulting in the connection

issue with the new router. In this case, select

RETRIEVE

, and follow the

onscreen instructions. You can also contact your carrier for assistance.

10

If the page prompts "Unable to retrieve conguration from old router", ensure

that the power supply of the old router, and the Ethernet cable connecting

the WAN port of the old router to the LAN port of the new router are all well

connected, then restart the old router and touch

TRY AGAIN

.

If the problem persists, restore the router to its factory settings and follow the instructions

in this guide to reconnect the cables and re-congure the router.

6.

8.

7.

How to restore the base and satellite routers to factory settings?

How do I connect an add-on Huawei router (with H/Hi button) to my HUAWEI

WiFi Q2 Pro's network?

Do satellite routers require reconguration after a factory reset?

Wired connection. Connect the WAN port of the add-on router (new or factory

reset) to the LAN port of the base router using an Ethernet cable.

The satellite router that comes in the pack is plug-and-play and does not need

to be recongured after a factory reset.

Plug the router to a power supply and wait for a few moments until the startup

is complete, then use a PIN to press and hold the RESET button on the router

for approximately two seconds until the indicator goes out. If the indicator turns

steady red after the router restarts, the router is restored to its factory settings.

However, satellite routers that are purchased separately must be recongured

through the HUAWEI SmartHome app.

If the base router is restored to its factory settings, you would need to recongure it, and

then restore all satellite routers to their factory settings as well.

11

9.

How do I pair a Wi-Fi device with my HUAWEI WiFi Q2 Pro using WPS?

When your HUAWEI WiFi Q2 Pro is powered on, press its H button, and then

press the WPS button on the Wi-Fi device (such as a phone) within two minutes

to initiate standard WPS negotiation and incorporate the Wi-Fi devices into the

router's Wi-Fi network.

Pairing through the H button. Step 1) Place the add-on router (new or factory

reset) within one meter of the base router and connect it to the power supply.

2) When the indicator on the base router starts to ash, press the H button on

it. Wait until the indicator on the add-on router shows it is connected to the

network.

Safety Information

THIS DOCUMENT IS FOR INFORMATION PURPOSE ONLY, AND DOES NOT CONSTITUTE

ANY KIND OF WARRANTIES.

Trademarks and Permissions

, , and are trademarks or registered trademarks of Huawei Technologies Co.,

Ltd.

Wi-Fi

®

, the Wi-Fi CERTIFIED logo, and the Wi-Fi logo are trademarks of Wi-Fi Alliance.

Other trademarks, product, service and company names mentioned may be the property of their

respective owners.

Version Update

In order to improve the security of the product and provide you with a better user experience,

we will push version update information to you on a regular basis when an important update is

released.

Privacy Policy

To better understand how we use and protect your personal information, please read the privacy

policy at http://consumer.huawei.com/privacy-policy.

12

End User License Agreement

Please read and agree to the End User License Agreement (HUAWEI EULA) on the product’s

management page before using the product.

Safety Information

• Do not use your device if using the device is prohibited. Do not use the device if doing so

causes danger or interference with other electronic devices.

• Pacemaker manufacturers recommend that a minimum distance of 15 cm be maintained

between a device and a pacemaker to prevent potential interference with the pacemaker. If

using a pacemaker, hold the device on the side opposite the pacemaker and do not carry the

device in your front pocket.

• Avoid dusty, damp, or dirty environments. Avoid magnetic elds. Using the device in these

environments may result in circuit malfunctions.

• Ideal operating temperatures are 0°C to 40°C. Ideal storage temperatures are -40°C to +70°C.

Extreme heat or cold may damage your device or accessories.

• Keep the device and accessories in a well-ventilated and cool area away from direct sunlight.

Do not enclose or cover your device with towels or other objects. Do not place the device in a

container with poor heat dissipation, such as a box or bag.

• The device should be installed and operated with a minimum distance of 20 cm between the

radiator and your body.

• Using an unapproved or incompatible power adapter, charger or battery may cause re,

explosion or other hazards.

• For pluggable devices, the socket-outlet shall be installed near the devices and shall be easily

accessible.

• Unplug the power adapter from electrical outlets and the device when not in use.

• Do not touch the device or the power adapter with wet hands. Doing so may lead to short

circuits, malfunctions, or electric shocks.

Disposal and recycling information

The crossed-out wheeled-bin symbol on your product, battery, literature or packaging

reminds you that all electronic products and batteries must be taken to separate waste

collection points at the end of their working lives; they must not be disposed of in the

normal waste stream with household garbage. It is the responsibility of the user to dispose

of the equipment using a designated collection point or service for separate recycling of waste

electrical and electronic equipment (WEEE) and batteries according to local laws.

Proper collection and recycling of your equipment helps ensure electrical and electronic

equipment (EEE) waste is recycled in a manner that conserves valuable materials and protects

13

human health and the environment, improper handling, accidental breakage, damage, and/

or improper recycling at the end of its life may be harmful for health and environment. For

more information about where and how to drop off your EEE waste, please contact your local

authorities, retailer or household waste disposal service or visit the website

http://consumer.huawei.com/en/.

Reduction of hazardous substances

This device and any electrical accessories are compliant with local applicable rules on the

restriction of the use of certain hazardous substances in electrical and electronic equipment,

such as EU REACH, RoHS and Batteries (where included) regulations, etc. For declarations of

conformity about REACH and RoHS, please visit our web site

http://consumer.huawei.com/certication.

EU regulatory conformance

Statement

Hereby, Huawei Technologies Co., Ltd. declares that the devices WS5280 V2 and PT8020 V2 are

in compliance with the essential requirements and other relevant provisions of Directive 2014/53/

EU.

The most recent and valid version of the DoC (Declaration of Conformity) can be viewed at

http://consumer.huawei.com/certication.

This device may be operated in all member states of the EU.

Observe national and local regulations where the device is used.

This device may be restricted for use, depending on the local network.

Restrictions in the 2.4 GHz band:

Norway:

This subsection does not apply for the geographical area within a radius of 20 km from

the centre of Ny-Ålesund.

Restrictions in the 5 GHz band:

According to Article 10 (10) of Directive 2014/53/EU, the packaging shows that this radio

equipment will be subject to some restrictions when placed

on the market in Belgium (BE), Bulgaria (BG), the Czech Republic (CZ), Denmark (DK), Germany

(DE), Estonia (EE), Ireland (IE), Greece (EL),

Spain (ES), France (FR), Croatia (HR), Italy (IT), Cyprus (CY), Latvia (LV), Lithuania (LT),

Luxembourg (LU), Hungary (HU), Malta (MT), Netherlands

(NL), Austria (AT), Poland (PL), Portugal (PT), Romania (RO), Slovenia (SI), Slovakia (SK),

Finland (FI), Sweden (SE), the United Kingdom (UK),

Turkey (TR), Norway (NO), Switzerland (CH), Iceland (IS), and Liechtenstein (LI).

The WLAN function for this device is restricted to indoor use only when operating in the 5150 to

14

5350 MHz frequency range.

Frequency bands and power

(a) Frequency bands in which the radio equipment operates: Some bands may not be available

in all countries or all areas. Please contact the local carrier for more details.

(b) Maximum radio-frequency power transmitted in the frequency bands in which the radio

equipment operates: The maximum power for all bands is less than the highest limit value

specied in the related Harmonized Standard.

The frequency bands and transmitting power (radiated and/or conducted) nominal limits

applicable to this radio equipment are as follows:

Wi-Fi 2.4G: 20 dBm, Wi-Fi 5G: 5150-5350 MHz: 23 dBm, 5470-5725 MHz: 30dBm.

Software Information

The product software versions are 9.0.3.8 (WS5280 V2) and 9.0.3.8 (PT8020 V2). Software

updates will be released by the manufacturer to x bugs or enhance functions after the product

has been released. All software versions released by the manufacturer have been veried and

are still compliant with the related rules.

All RF parameters (for example, frequency range and output power) are not accessible to the

user, and cannot be changed by the user.

For the most recent information about accessories and software, please see the DoC (Declaration

of Conrmation) at http://consumer.huawei.com/certication.

ErP Product Information

Huawei Technologies Co., Ltd. hereby declares that its products conform to the Energy-related

Products Directive (ErP) 2009/125/EC.

For detailed ErP information and the user manuals required by Commission Regulation, please

visit: http://consumer.huawei.com/en/certication.

Please visit http://consumer.huawei.com/en/support/hotline for recently updated hotline and email

address in your country or region.

15

Guide de démarrage rapide

Après avoir conguré le routeur base, branchez simplement le

routeur satellite à une source d'alimentation pour accéder à Internet.

Bouton H

Port d'alimentation

Bouton RESET

(Version UE)

Port LAN : pour

la connexion

d'appareils Internet

laires, tel qu'un

ordinateur.

Port WAN : pour la connexion de

modems optiques, modems haut

débit, etc.

Port LAN : pour la connexion

d'appareils Internet laires, tel qu'un

ordinateur.

Voyant

Mise en route

Routeur base

Routeur satellite

(Version RU)

Bouton RESET

Port LAN : pour

la connexion

d'appareils

Internet laires, tel

qu'un ordinateur.

16

Étape 2 : connecter les câbles

Sortez le routeur base, puis connectez le câble Ethernet et l'alimentation.

Modem optique/haut débit/laire

Prise murale

HUAWEI WiFi Q2 Pro

Insérez le câble dans

le port WAN du routeur.

L'utilisation d'une

multiprise n'est

pas recommandée

Internet

Ou

de votre fournisseur d'accès

Ne regroupez pas le câble Ethernet et le câble d'alimentation. Cela risquerait d'affecter le

signal du routeur.

Recherchez « HUAWEI SmartHome » sur une boutique d'applications ou scannez

le code QR situé ci-dessous pour télécharger et installer l'application HUAWEI

SmartHome.

Étape 1 : installer l'application HUAWEI SmartHome

Si l'application HUAWEI SmartHome est déjà installée sur votre téléphone, vériez que vous

avez bien la version la plus récente.

La page charge ...

Huawei WiFi Q2 Pro Guide de démarrage rapide

Huawei WiFi Q2 Pro Guide de démarrage rapide

dans d''autres langues

Documents connexes

Autres documents