Huawei 5G CPE Pro 2 Quick Start

Taper
Quick Start
Quick Start
Démarrage rapide
Installationsanleitung
Avvio rapido
Snelstartgids
Início rápido
Inicio rápido
Contents
English.......................................................................................................................................................1
Français................................................................................................................................................... 12
Deutsch....................................................................................................................................................24
Italiano..................................................................................................................................................... 36
Nederlands.............................................................................................................................................. 47
Português................................................................................................................................................ 58
Español....................................................................................................................................................69
i
Product overview
5 7
6
8
9
10
11
12
1
2
3
4
1
Landline phone port(Optional.
The actual product appearance
and functions prevail.)
2
LAN port
3
LAN/WAN port
4
Power input
5
SIM card slot
6
Reset button
7
Power button
Ambient light strip
9
H button
10
Wi-Fi
®
indicator
11
4G signal indicator
12
5G signal indicator
English
1
Setup
1 Make sure you use the correct SIM card.
mini-SIM (2FF)
micro-SIM (3FF)
nano-SIM (4FF)
2 Open the SIM card cover.
3 Insert the SIM card gently into the SIM card slot in the direction shown in the figure below until it
clicks. Then close the SIM card cover.
To remove the SIM card, gently press the SIM card in until it clicks. The card will
automatically pop out.
Do not insert or remove a SIM card when the router is running, as this may affect
performance or damage the SIM card.
4 Connect the power adapter to the router.
2
The indicators will turn on when the router has successfully connected to a network.
5G signal indicator
Green: Strong.
Yellow: Moderate.
Red: Weak.
4G signal indicator
Green: Strong.
Yellow: Moderate.
Red: Weak.
If both the 5G signal indicator and 4G signal indicator are off, it indicates there is no network
connection. Please refer to the FAQs in this guide.
3
Connecting to your router's Wi-Fi network
Wi-Fi Password:
Wi-Fi Password:
Wi-Fi Name:XXXXXXXX
Wi-Fi Name(5GHz):XXXXX
Wi-Fi Password:YYYYYYYY
Once the router has connected to a mobile data network, you can connect your computer or mobile
phone to the router's Wi-Fi network to access the Internet. Please refer to the label on the bottom of the
router for the default Wi-Fi network name (Wi-Fi Name) and password (Wi-Fi Password).
When the Wi-Fi indicator is steady on, Wi-Fi is enabled. To enable or disable Wi-Fi, refer to
the router's web-based management page.
Ensure that you promptly change the Wi-Fi network name and password on the web-based
management page to prevent unauthorized access to your Wi-Fi network. Once you have
changed the password, you will need to reconnect to the router's Wi-Fi network.
If you accidentally pressed the H button and the Wi-Fi indicator starts to flash, wait for it to
stop flashing. This may take about two minutes.
4
Managing your router
Password:
zzz
XXX.XXX.X.X
XXX.XXX.X.X
IP:XXX.XXX.X.X
Password:zzz
Password:
zzz
You can manage the router using the web-based management page. Please refer to the label on the
bottom of the router for the default IP address, password and so on.
More information can be found in the web-based management page.
Ensure that you promptly change the default login password for the web-based management
page to prevent unauthorized users from changing the router's settings.
You can also manage your router using the HUAWEI AI Life app. Scan the QR code below to
download.
5
Optional configurations
The features described in this section are for reference purposes only. Your router may not support all of
these features.
Connecting computer
You can connect a computer to the router to access the Internet.
Accessing the Internet through an Ethernet port
You can connect the router to a wall-mounted Ethernet port using an Ethernet cable to connect to the
Internet.
Configure the relevant settings on the web-based management page before connecting to the Internet
through an Ethernet port. For details, please contact your carrier.
6
FAQs
How do I restore factory settings?
When the router is turned on, press the Reset button for approximately 3 seconds using a pointed object
until the ambient light strip starts to blink. Restoring factory settings will restore the settings to the
default. You can reconfigure them after the router is restored.
What should I do if I forgot the Wi-Fi password or the login password for the web-
based management page?
Restore the router to its factory settings and then use the default Wi-Fi password and login password to
try again.
What should I do if the 5G signal indicator and 4G signal indicator are off or an
Internet connection cannot be established?
1 Check if the SIM card is inserted. Refer to the Setup section for the right size of SIM card and the right
way to insert it into the slot.
2 If the issue persists, restore the router to factory settings and try again.
3 Contact your carrier to check if your SIM card is out of service. If it's a new card, check if it has been
activated.
What should I do if the Internet speed is slow?
1 Check the 5G signal indicator and 4G signal indicator on the router. If both of them are red, adjust the
router's direction or move it close to a window to improve signal reception.
2 If your device is connected to the router over Wi-Fi, adjust your device's position to receive better
signal.
3 Switch to Wi-Fi 5 GHz if it is supported by your device.
4 Restart the router and your device, and try again.
5 Check if you have reached your data traffic limit for the month. If so, your carrier may limit your
Internet speed.
How can I connect to the router using WPS (Wi-Fi Protected Setup)?
To connect a WPS-enabled device to your router using the H button:
1 Press the H button on the router, and the Wi-Fi indicator will start to flash.
2 Enable WPS on your device within 2 minutes to connect to the router's Wi-Fi network.
How do I use the H button to pair my router with a HUAWEI HiLink device?
When your router detects a HUAWEI HiLink device that can be paired, the Wi-Fi indicator on the router
will automatically start flashing. After pressing the H button on the router, the Wi-Fi indicator will begin to
flash faster, and the device will connect to the router's Wi-Fi network. After the pairing is successful, the
Wi-Fi indicator on the router will stop flashing (this feature is only supported on HUAWEI HiLink
devices).
Why can't I access the router's web-based management page?
1 Ensure that your computer is connected to the router through an Ethernet cable or Wi-Fi.
2 Ensure that your computer is set to obtain an IP address and DNS server address automatically.
3 Restart your browser, or try using another browser.
4 If the problem persists, restore the router to its factory settings.
Why is the content displayed on the web-based management page not up to date?
Depending on your browser's cache, the content for your device on the web-based management page
may not be up to date. Manually clear your browser's cache (for example, open your browser and
7
choose Internet Options > General > Browsing history > Delete.) and re-launch the web-based
management page.
If you are experiencing any other issues with the router:
1 Restart the router.
2 Restore the router to its factory settings.
3 Contact your carrier.
8
Safety information
Copyright © Huawei 2020. All rights reserved.
THIS DOCUMENT IS FOR INFORMATION PURPOSE ONLY, AND DOES NOT CONSTITUTE ANY
KIND OF WARRANTIES.
LTE is a trademark of ETSI.
Wi-Fi
®
, the Wi-Fi CERTIFIED logo, and the Wi-Fi logo are trademarks of Wi-Fi Alliance.
Privacy Policy
To better understand how we use and protect your personal information, please read the Privacy Policy
at
http://consumer.huawei.com/privacy-policy
.
To understand how we use and protect your personal information on this device, open the web-based
management page or HUAWEI AI Life app, access Statement about Huawei Mobile Broadband Devices
and Privacy, and read our privacy policy.
Software Update
By continuing to use this device, you indicate that you have read and agree to the following content:
In order to provide better service, this device will automatically obtain software update information from
Huawei or your carrier after connecting to the Internet. This process will use mobile data, and requires
access to your device's unique identifier (IMEI/SN) and the service provider network ID (PLMN) to check
whether your device needs to be updated.
This device supports the automatic update feature. Once enabled, the device will automatically
download and install critical updates from Huawei or your carrier. The function is enabled by default, and
can be disabled from the settings menu on the web-based management page.
Safety information
Some wireless devices may affect the performance of hearing aids or pacemakers. Consult your
service provider for more information.
Pacemaker manufacturers recommend that a minimum distance of 20 cm be maintained between a
device and a pacemaker to prevent potential interference with the pacemaker. If using a pacemaker,
hold the device on the side opposite the pacemaker and do not carry the device in your front pocket.
Ideal operating temperatures are 0 °C to 40 °C. Ideal storage temperatures are -20 °C to +70 °C.
Extreme heat or cold may damage your device or accessories.
Keep the device and accessories in a well-ventilated and cool area away from direct sunlight. Do not
enclose or cover your device with towels or other objects. Do not place the device in a container with
poor heat dissipation, such as a box or bag.
Keep the device away from sources of heat and fire, such as a heater, microwave oven, stove, water
heater, radiator, or candle.
The device should be installed and operated with a minimum distance of 20 cm between the radiator
and your body.
Using an unapproved or incompatible power adapter, charger or battery may cause fire, explosion or
other hazards.
Choose only accessories approved for use with this model by the device manufacturer. The use of
any other types of accessories may void the warranty, may violate local regulations and laws, and
may be dangerous. Please contact your retailer for information about the availability of approved
accessories in your area.
The power plug is intended to serve as a disconnect device.
For pluggable devices, the socket-outlet shall be installed near the devices and shall be easily
accessible.
Ensure that the power adapter meets the requirements of Clause 2.5 in IEC60950-1/EN60950-1/
UL60950-1 and has been tested and approved according to national or local standards.
Areas with flammables and explosives: Do not use the device where flammables or explosives are
stored (in a gas station, oil depot, or chemical plant, for example). Using your device in these
9
environments increases the risk of explosion or fire. In addition, follow the instructions indicated in text
or symbols. Do not store or transport the device in containers with flammable liquids, gases, or
explosives.
Blasting Caps and Areas: Turn off your device or wireless device when in a blasting area or in areas
posted turn off “two-way radios” or “electronic devices” to avoid interfering with blasting operations.
Medical devices: Please consult your doctor and the device manufacturer to determine if operation of
your device may interfere with the operation of your medical device.
Hospitals: Switch off your wireless device when requested to do so in hospitals, clinics or health care
facilities. These requests are designed to prevent possible interference with sensitive medical
equipment.
Aircraft: Switch off your wireless device whenever you are instructed to do so by airport or airline staff.
Consult the airline staff about the use of wireless devices on board the aircraft, if your device offers a
‘flight mode’ this must be enabled prior to boarding an aircraft.
Disposal and recycling information
The crossed-out wheeled-bin symbol on your product, battery, literature or packaging reminds you that
all electronic products and batteries must be taken to separate waste collection points at the end of their
working lives; they must not be disposed of in the normal waste stream with household garbage. It is the
responsibility of the user to dispose of the equipment using a designated collection point or service for
separate recycling of waste electrical and electronic equipment (WEEE) and batteries according to local
laws.
Proper collection and recycling of your equipment helps ensure electrical and electronic equipment
(EEE) waste is recycled in a manner that conserves valuable materials and protects human health and
the environment, improper handling, accidental breakage, damage, and/or improper recycling at the end
of its life may be harmful for health and environment. For more information about where and how to drop
off your EEE waste, please contact your local authorities, retailer or household waste disposal service or
visit the website http://consumer.huawei.com/en/.
Reduction of hazardous substances
This device and its electrical accessories are compliant with local applicable rules on the restriction of
the use of certain hazardous substances in electrical and electronic equipment, such as EU REACH,
RoHS and Batteries (where included) regulations. For declarations of conformity about REACH and
RoHS, please visit our web site
http://consumer.huawei.com/certification
.
EU regulatory conformance
Statement
Hereby, Huawei Technologies Co., Ltd. declares that this device H122-373 is in compliance with the
essential requirements and other relevant provisions of Directive 2014/53/EU.
The most recent and valid version of the DoC (Declaration of Conformity) can be viewed at
http://consumer.huawei.com/certification
.
This device may be operated in all member states of the EU.
Observe national and local regulations where the device is used.
This device may be restricted for use, depending on the local network.
Restrictions in the 2.4 GHz band:
Norway: This subsection does not apply for the geographical area within a radius of 20 km from the
centre of Ny-Ålesund.
Restrictions in the 5 GHz band:
According to Article 10 (10) of Directive 2014/53/EU, the packaging shows that this radio equipment will
be subject to some restrictions when placed on the market in Belgium (BE), Bulgaria (BG), the Czech
10
Republic (CZ), Denmark (DK), Germany (DE), Estonia (EE), Ireland (IE), Greece (EL), Spain (ES),
France (FR), Croatia (HR), Italy (IT), Cyprus (CY), Latvia (LV), Lithuania (LT), Luxembourg (LU),
Hungary (HU), Malta (MT), Netherlands (NL), Austria (AT), Poland (PL), Portugal (PT), Romania (RO),
Slovenia (SI), Slovakia (SK), Finland (FI), Sweden (SE), the United Kingdom (UK), Turkey (TR), Norway
(NO), Switzerland (CH), Iceland (IS), and Liechtenstein (LI).
The WLAN function for this device is restricted to indoor use only when operating in the 5150 to 5350
MHz frequency range.
ErP Product Information
Huawei Technologies Co., Ltd. hereby declares that its products conform to the Energy-related Products
Directive (ErP) 2009/125/EC. For detailed ErP information and the user manuals required by
Commission Regulation, please visit: http://consumer.huawei.com/en/certification.
Frequency Bands and Power
(a) Frequency bands in which the radio equipment operates: Some bands may not be available in all
countries or all areas. Please contact the local carrier for more details.
(b) Maximum radio-frequency power transmitted in the frequency bands in which the radio equipment
operates: The maximum power for all bands is less than the highest limit value specified in the related
Harmonized Standard.
The frequency bands and transmitting power (radiated and/or conducted) nominal limits applicable to
this radio equipment are as follows: LTE Band 1/3/7/8/20/28/34/38/40: 25.7 dBm, LTE Band 42/43: 26
dBm, 5G NR n1/n3/n7/n28/n38/n40/n41/n77/n78/n80/n84: 29 dBm, Wi-Fi 2.4G: 20 dBm, Wi-Fi 5G:
5150-5350 MHz: 23 dBm, 5470-5725 MHz: 30 dBm.
Accessories and Software Information
Some accessories are optional in certain countries or regions. Optional accessories can be purchased
from a licensed vendor as required. The following accessories are recommended:
Adapters: HW-120200X01 (X represents the different plug types used, which can be either C, U, J, E, B,
A, I, R, Z or K, depending on your region)
The product software version is 10.0.5.7(H612SP3C00). Software updates will be released by the
manufacturer to fix bugs or enhance functions after the product has been released. All software versions
released by the manufacturer have been verified and are still compliant with the related rules.
All RF parameters (for example, frequency range and output power) are not accessible to the user, and
cannot be changed by the user.
For the most recent information about accessories and software, please see the DoC (Declaration of
Conformity) at http://consumer.huawei.com/certification.
Please visit http://consumer.huawei.com/en/support/hotline for recently updated hotline and email
address in your country or region.
11
Présentation du produit
5 7
6
8
9
10
11
12
1
2
3
4
1
Port ligne xe (Optionnel.
L'apparence et les fonctions du
produit réel prévalent.)
2
Port LAN
3
Port LAN/WAN
4
Entrée d'alimentation
5
Emplacement pour carte SIM
6
Bouton de réinitialisation
7
Bouton marche/arrêt
Barre de lumière ambiante
9
Bouton H
10
Voyant Wi-Fi
®
11
Voyant du signal 4G
12
Voyant du signal 5G
Français
12
Conguration
1 Assurez-vous d'utiliser une carte SIM appropriée.
mini-SIM (2FF)
micro-SIM (3FF)
nano-SIM (4FF)
2 Ouvrez le cache de la carte SIM.
3 Insérez délicatement la carte SIM dans son emplacement, en respectant l'orientation indiquée sur
le schéma ci-dessous, jusqu'à sentir un clic. Refermez ensuite le cache de la carte SIM.
Pour retirer la carte SIM, exercez une légère pression sur la carte SIM jusqu'à sentir un
clic. La carte sortira alors automatiquement.
Veuillez ne pas insérer ou retirer de carte SIM pendant le fonctionnement du routeur, car
cela pourrait nuire aux performances ou endommager la carte SIM.
4 Branchez l'adaptateur secteur au routeur.
13
Les voyants s'allument lorsque le routeur est connecté à un réseau.
Voyant du signal 5G
Vert : bon
Jaune : modéré
Rouge : faible
Voyant du signal 4G
Vert : bon
Jaune : modéré
Rouge : faible
Si les voyants des signaux 5G et 4G sont rouges, cela indique qu'il n'y a pas de connexion
réseau. Veuillez consulter la FAQ de ce guide.
14
Connexion au réseau Wi-Fi de votre routeur
Wi-Fi Password:
Wi-Fi Password:
Wi-Fi Name:XXXXXXXX
Wi-Fi Name(5GHz):XXXXX
Wi-Fi Password:YYYYYYYY
Une fois le routeur connecté à un réseau de données mobiles, vous pouvez connecter votre
ordinateur ou téléphone portable au réseau Wi-Fi du routeur pour accéder à Internet. Veuillez vous
reporter à l'étiquette située au-dessous du routeur pour connaître le nom du réseau Wi-Fi (Wi-Fi
Name) et le mot de passe (Wi-Fi Password) par défaut.
Le Wi-Fi est activé lorsque le voyant Wi-Fi est allumé de manière continue. Pour activer ou
désactiver le Wi-Fi, veuillez vous référer à l'interface Web de gestion du routeur.
Il est recommandé de modier rapidement le nom du réseau Wi-Fi et le mot de passe sur
l'interface Web de gestion du routeur an d'empêcher tout accès non autorisé à votre
réseau Wi-Fi. Une fois le mot de passe modié, vous devrez vous reconnecter au réseau
Wi-Fi du routeur.
En cas d'appui accidentel sur le bouton H, entraînant le clignotement de l'indicateur Wi-Fi,
veuillez attendre que ce dernier s'arrête de clignoter. Ceci pourrait prendre environ deux
minutes.
15
Gestion de votre routeur
Password:
zzz
XXX.XXX.X.X
XXX.XXX.X.X
IP:XXX.XXX.X.X
Password:zzz
Password:
zzz
Vous pouvez gérer le routeur à partir de son interface Web de gestion. Veuillez vous reporter à
l'étiquette située au-dessous du routeur pour connaître l'adresse IP et le mot de passe par défaut,
ainsi que d'autres informations.
Des informations complémentaires sont disponibles sur l'interface Web de gestion.
Veillez à modier rapidement le mot de passe par défaut de connexion à l'interface Web
de gestion an d'empêcher que des utilisateurs non autorisés ne puissent modier les
paramètres du routeur.
Le routeur peut également être géré via l'application HUAWEI AI Life. Scannez le QR code
ci-dessous pour la télécharger.
16
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84

Huawei 5G CPE Pro 2 Quick Start

Taper
Quick Start

dans d''autres langues