Paradigm Premier 500C Manuel utilisateur

Taper
Manuel utilisateur
Owner’s Manual
RECYCLING AND REUSE GUIDELINES (Europe)
In accordance with the European Union WEEE (Waste Electrical and Electronic Equipment) directive effective August 13, 2005, we
would like to notify you that our speakers may contain regulated materials which, upon disposal, require special reuse and recycling
processing. For this reason Paradigm Electronics Inc. (the manufacturer of Paradigm speakers and Anthem electronic products) has
arranged with its distributors in European Union member nations to collect and recycle this product at no cost to you. To find your
local distributor please contact the dealer from whom you purchased this product or go to our website at www.paradigm.com.
Please note that only the product falls under the WEEE directive. When disposing of packaging and other shipping material we
encourage you to recycle through the normal channels.
MAN0149 | 020118
Thank you!
Thank you for choosing Paradigm Premier Series speakers. You are
about to hear the difference that sonically accurate speakers make in
your audio/home theater system! They are the product of countless
hours of comprehensive research and development and will reward
you with truly exceptional sound for many years.
To ensure proper installation and enjoy all of the exceptional sound
these speakers are designed to provide, please read this manual
and follow all instructions. If you have further questions contact your
Authorized Paradigm Dealer or visit the Q&A page on our website at
www.paradigm.com.
Floorstanding Speakers —
Attaching Carpet Spikes or Rubber Caps ................................... 2
Bookshelf / Center Channel Speakers —
Applying Rubber Pads .................................................................... 3
Your New Speakers ....................................................................... 4
Preventing Speaker Damage ........................................................ 5
Room Acoustics ............................................................................ 7
Placement: Front Left & Right Speakers ..................................... 8
Placement: The Center Speaker ................................................ 12
Placement: Surround/Rear Speakers ........................................ 13
Wiring ............................................................................................ 14
Standard Connection (Premier 100B and 200B) ....................... 15
Other Connection Options .......................................................... 16
Fine Tuning ................................................................................... 21
Troubleshooting Guide ............................................................... 22
Limited Warranty ......................................................................... 23
TABLE OF CONTENTS
2
Floor (Wood or Tile) Carpet
FLOORSTANDING SPEAKERS —
ATTACHING CARPET SPIKES OR
RUBBER CAPS
OR
The screw thread specification is 1/4”-20.
paradigm.com
3
BOOKSHELF / CENTER CHANNEL
SPEAKERS — APPLYING RUBBER PADS
BOOKSHELF SPEAKERS (Premier 100B and 200B)
Self-adhesive rubber pads (included) must be applied to the bottom
corners of bookshelf and center channel speakers (as shown) when
placed on a shelf or other flat surface.
CENTER CHANNEL SPEAKERS (Premier 500C and 600C)
Apply self-adhesive rubber pads (included) as shown on the Rubber Pad
Installation Template.
Front View of
Bumper Pad
Bottom View of Bookshelf Speaker
4
Break-In
Although Paradigm Premier Series speakers sound great “out of the
carton,” they will sound even better when broken in. Allow them to
operate for several hours before you listen critically.
High-frequency drivers use ferro-fluid that can thicken at temperatures
below 10° C (50° F). If your speakers have been transported or stored in
the cold let them warm to room temperature before use.
Cleaning
Do not use a strong or abrasive cleaner on your speakers. Clean
them with a damp soft cloth, but do not get them wet. Do not place
wet objects, such as drinking glasses or potted plants, on top of the
speakers. If allowed to soak in, even a small amount of water may
permanently damage the speaker enclosure.
Optional Spikes and Rubber Feet
Floorstanding speakers ship with rubber feet pre-installed. These can
be easily removed if you intend to use isolation spikes (included with
floorstanding speaker models). We highly recommend installing these
spikes as they will improve the sound of your speakers by isolating them
from the floor. The most convenient time to install these spikes is during
the unpacking process.
Optional Paradigm Speaker Stands
We highly recommend placing Paradigm Premier Series bookshelf
speakers on high-performance Paradigm speaker stands (sold
separately), or bookshelves to raise the high-frequency drivers to
approximately ear level, thereby ensuring the best performance possible.
YOUR NEW SPEAKERS
paradigm.com
5
To prevent damage to your speakers, please read the following
guidelines before making any connections.
Amplifier Distortion—The #1 Culprit!
Amplifier distortion is the principle cause of speaker damage. When
listening at higher volume levels, your amplifier may run out of clean
power and begin to produce a distorted signal if levels are increased any
further. This will damage any brand of speaker very quickly. (See your
Authorized Paradigm Dealer for amplifier recommendations).
More Powerful Amplifiers are Safer
When choosing an amplifier, always select an amplifier with a power
rating greater than that of the speaker. Using a 100W per channel
amplifier on a 50W speaker allows the amplifier adequate headroom in
order to provide a distortion free signal. Conversely, using a 40W per
channel amplifier on a 50W speaker limits the amplifier’s headroom. This
causes the amplifier to enter its distortion level much sooner, potentially
damaging the speaker.
Volume Control
Do not be fooled by the Volume Control of your receiver/preamplifier. It
only adjusts listening level—it is not a “power-output” dial. The amount of
amplifier power actually used at a given Volume Control setting depends
solely on the nature of the music you are listening to. At a given Volume
Control setting a quiet section of music will use less amplifier power than
a loud section. With typical pop-rock, jazz or large scale classical music
the rated output power of many receivers/amplifiers is often reached
when the Volume Control is between the “11” and “1” o’clock settings
(with bass/ treble and loudness controls not used—otherwise rated
power may be reached at even lower Volume Control settings).
Remember, all amplifiers produce distortion when operated beyond their
rated output power. The resulting distortion will damage all speakers!
Exercise caution! If you listen at loud levels, be careful to listen for the
point of audible distortion—if the speakers begin to sound distressed,
turn the Volume Control down or your speakers and/or amplifier(s) will
be damaged! This type of damage constitutes abuse and is not covered
by the warranty. If louder volumes are desired, obtain a more powerful
amplifier.
PREVENTING SPEAKER DAMAGE
6
There is a Limit!
Although more powerful amplifiers are safer, there is a point at which
you could have more power than the speaker can handle. At that point
you will overpower the speaker and damage it. Exercise caution! At loud
levels do not increase bass/treble controls from zero and ensure that
all loudness/ contour/bass EQ buttons are off (otherwise rated output
power will be reached at lower volume control settings). If you listen at
loud levels, watch for excessive visible cone excursion (grille movement)
from the woofer—then turn the Volume Control down.
The Right Amount of Power
A power-range rating is given as a guide to indicate the approximate
minimum and maximum power input of your Paradigm speakers.
Amplifiers that exceed your speaker’s power-range rating are
recommended. Their greater power reserves provide better sound.
However, exercise caution! Use the speakers within their power-range
rating to prevent damage (keep listening levels below the point of
excessive woofer cone excursion).
PREVENTING SPEAKER DAMAGE (cont’d)
paradigm.com
7
Paradigm Premier Series speakers are designed to provide exceptional
sound in a wide variety of domestic settings. However, it is important
to note that listening room construction, dimensions and furnishings all
play a part in the quality of sound you will ultimately achieve. Your listening
room will impose its own character on the performance capabilities of any
speaker system. The extra care you take in correctly positioning the
speakers will result in greater listening enjoyment. Keep the following
guidelines in mind when deciding on the best speaker placement:
Mid and high frequencies are affected by the amount of soft furnishings
in your room—curtains, carpets, sofas, wall coverings, etc. An excess
of such items can result in a somewhat dull sound. The same room
without any soft furnishings can produce an overall bright sound. The
typical quantity of soft furnishings found in most living environments
provides the right acoustic characteristics to allow the speakers to
sound balanced;
Concrete floors and walls tend to aggravate low-frequency standing
wave problems and are less preferred;
Rooms where height, width and length are similar should be
avoided as they can exhibit significant low-frequency standing wave
problems. This may result in reduced clarity. If no other room is possible,
experiment with speaker placement to minimize acoustic problems.
ROOM ACOUSTICS
8
PLACEMENT: Front Left & Right Speakers
Ideal placement of front and center speakers
Paradigm Premier Series front speakers are designed to
allow flexible placement while providing a very large window
of sound throughout your listening room. To ensure the best
performance possible we strongly recommend that you
observe the placement guidelines on the following pages …
paradigm.com
9
Accurate Timbre
For the most accurate and natural timbre, place front speakers so that
their high-frequency drivers are approximately at ear level, as shown.
Placing bookshelf models on Paradigm speaker stands (sold separately)
or bookshelves raises their high-frequency drivers to approximately ear
level, thereby ensuring the best performance possible.
8” (20 cm)
8po (20 cm)
10
Balanced Bass
Placing front speakers in corners will over-emphasize bass and reduce
overall clarity. Avoid corner placement. Position front speakers 8 in
(20 cm) or more from the wall behind the speaker and as much as
possible from either side wall, as shown in. This will ensure better bass
performance and optimal midrange clarity.
PLACEMENT: Front Left & Right Speakers
(cont’d)
8” (20 cm)
8po (20 cm)
paradigm.com
11
Optimal Imaging
Measure the distance from your main listening area to the front speakers
(“X”). For best imaging, place speakers from three-quarters of that
distance up to that same distance from each other (3/4 of “X” to “X”),
as shown. To further optimize imaging, toe speakers slightly inward so
they point toward the listening position with their axes crossing just behind
it, as shown.
12
The Paradigm Premier Series center speaker is designed to cover a
large, wide listening area, allowing listeners throughout the room to hear
center-channel information with unprecedented clarity and intelligibility.
Placing your center-channel speaker below the TV will ensure the
best possible clarity and intelligibility. Position the speaker flush with
the front of the TV or speaker shelf to minimize unwanted sound
reflections. Make sure the center-channel speaker is approximately
the same distance away from the primary listening position as your
front speakers. (Some A/V receivers and processors can electronically
adjust for differences in distance.)
PLACEMENT: Center Speaker
paradigm.com
13
Paradigm Premier bookshelf speakers may also be used as surround or
rear speakers. Remember to keep these speakers well away from the
main listening area for optimal surround-sound performance.
5.1 Surround Speaker Placement
for Paradigm Premier 100B & 200B
SURROUND SPEAKER PLACEMENT
FOR PARADIGM PREMIER 100B & 200B
7.1 Surround Speaker Placement
for Paradigm Premier 100B & 200B
90˚
135˚
150˚
90˚
110 ˚
135˚
150˚
110 ˚
90˚
135˚
min. 2 ft. min. 2 ft.
150˚
90˚
90˚ 90˚
110 ˚
135˚
150˚
110 ˚
110 ˚110 ˚
110 ˚
120˚
110 ˚
120˚
5.1 Surround Speaker Placement
for Paradigm Premier 100B & 200B
7.1 Surround Speaker Placement
for Paradigm Premier 100B & 200B
5.1 Surround Speaker Placement
for Paradigm Premier 300S & 400S
7.1 Surround Speaker Placement
for Paradigm Premier 300S & 400S
90˚
135˚
150˚
90˚
110 ˚
135˚
150˚
110 ˚
90˚
135˚
min. 2 ft. min. 2 ft.
150˚
90˚
90˚ 90˚
110 ˚
135˚
150˚
110 ˚
110 ˚110 ˚
110 ˚
120˚
110 ˚
120˚
5.1 Surround Speaker Placement
for Paradigm Premier 100B & 200B
7.1 Surround Speaker Placement
for Paradigm Premier 100B & 200B
5.1 Surround Speaker Placement
for Paradigm Premier 300S & 400S
7.1 Surround Speaker Placement
for Paradigm Premier 300S & 400S
PLACEMENT: Surround / Rear Speakers
14
WIRING
For optimum sound, the use of high quality speaker cable is essential.
The chart below identifies the minimum gauge requirements for various
lengths. See your Authorized Paradigm Dealer for recommendations.
MINIMUM GAUGE REQUIREMENTS
LENGTH DIAMETER GAUGE
Under 4.5 m (15 ft) 1.3 mm (0.05 in) 16 awg
Under 9 m (30 ft) 1.6 mm (0.06 in) 14 awg
Over 9 m (30 ft) 2.0 mm (0.08 in) 12 awg
Turn your amplifier(s) OFF before connecting your
speakers. This will avoid damage which could
result from accidental shorting of speaker cables.
paradigm.com
15
Your speakers’ binding posts can be used with banana, pin or spade
connectors, as well as with bare wire. Tighten the posts firmly by hand
but do not over tighten!
Correct polarity (or phase) is critical for proper soundstage imaging and
bass performance. Connect one speaker at a time to ensure proper
connection of every channel. The red (+) amplifier terminal must be
connected to the red (+) speaker terminal. The same applies to the black (–)
terminals. Make sure all wires are firmly fastened. Repeat this connection
procedure for each speaker in your system.
NOTE: If you hear a distinct lack of bass and a dislocated stereo image then
one or more of your speakers may be connected out of phase (polarity is
reversed). Re-check to ensure that each speakers’ cable is connected with
correct polarity: red (+) to red (+) and black (–) to black (–).
-+
STANDARD CONNECTION
(Premier 100B and 200B)
16
Some Paradigm Premier Series speakers have two sets of input
terminals connected externally with jumper bars. These speakers can
be bi-wired or also bi-amplified to achieve even better performance.
If your speakers do not have two sets of input terminals this section
does not apply to you.
OTHER CONNECTION OPTIONS
DO NOT attempt to bi-wire or bi-amplify speakers
unless you have removed the jumper bars.
paradigm.com
17
-+
Standard Connection of Speakers with Two Input Terminals
For standard connection of speakers with two input terminals, leave
the jumper bars attached and connect using either set of input terminals.
18
-+
Bi-wire Connection
Bi-wiring can improve clarity and openness with less grain and more
solidity to the bass. Two speaker cables are required for each speaker
that is bi-wired.
OTHER CONNECTION OPTIONS (cont’d)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

Paradigm Premier 500C Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues