Paradigm Monitor SE Atom Manuel utilisateur

Taper
Manuel utilisateur
Owner’s Manual
Monitor-SE Series Owners Manual_090617.indd 1 2017-09-07 10:40 AM
www.paradigm.com
1
RECYCLING AND REUSE GUIDELINES (Europe)
In accordance with the European Union WEEE (Waste Electrical and Electronic Equipment) directive effective August 13, 2005, we
would like to notify you that our speakers may contain regulated materials which, upon disposal, require special reuse and recycling
processing. For this reason Paradigm Electronics Inc. (the manufacturer of Paradigm speakers and Anthem electronic products) has
arranged with its distributors in European Union member nations to collect and recycle this product at no cost to you. To find your
local distributor please contact the dealer from whom you purchased this product or go to our website at www.paradigm.com.
Please note that only the product falls under the WEEE directive. When disposing of packaging and other shipping material we
encourage you to recycle through the normal channels.
090617
To ensure proper installation and enjoy all of the exceptional sound
these speakers are designed to provide, please read this manual
and follow all instructions. If you have further questions contact your
Authorized Paradigm Dealer or visit the Q&A page on our website at
www.paradigm.com.
Monitor-SE Series Owners Manual_090617.indd 1 2017-09-07 10:40 AM
www.paradigm.com
2
Floorstanding Speakers Attaching Carpet
Spikes or Rubber Caps ................................. 3
Bookshelf / Center Channel Speakers –
Applying Rubber Pads .................................. 4
Your New Speakers ...................................... 5
Preventing Speaker Damage ........................ 6
Room Acoustics ............................................ 8
Placement: Front L & R Speakers ................ 9
Placement: The Center Speaker ................ 13
Wiring .......................................................... 14
Speaker Connection ................................... 15
Fine Tuning .................................................. 16
Troubleshooting Guide ................................ 17
Limited Warranty ......................................... 18
TABLE OF CONTENTS
Monitor-SE Series Owners Manual_090617.indd 2 2017-09-07 10:40 AM
www.paradigm.com
3
Floor (Wood or Tile) Carpet
FLOORSTANDING SPEAKERS —
ATTACHING CARPET SPIKES OR
RUBBER CAPS
OR
Monitor-SE Series Owners Manual_090617.indd 3 2017-09-07 10:40 AM
www.paradigm.com
4
BOOKSHELF / CENTER CHANNEL
SPEAKERS — APPLYING RUBBER PADS
Self-adhesive rubber pads (included) must be applied to the bottom
corners of bookshelf and center channel speakers (as shown) when
placed on a shelf or other flat surface.
Bottom View of Bookshelf / Center Channel Speaker
Monitor-SE Series Owners Manual_090617.indd 4 2017-09-07 10:40 AM
www.paradigm.com
5
Break-In
Although Paradigm Monitor SE Series speakers sound great “out of
the carton,” they will sound even better when broken in. Allow them to
operate for several hours before you listen critically.
High-frequency drivers use ferro-fluid that can thicken at temperatures
below 10° C (50° F). If your speakers have been transported or stored
in the cold let them warm to room temperature before use.
Cleaning
Do not use a strong or abrasive cleaner on your speakers. Clean
them with a damp soft cloth, but do not get them wet. Do not place
wet objects, such as drinking glasses or potted plants, on top of the
speakers. If allowed to soak in, even a small amount of water may
permanently damage the speaker enclosure.
YOUR NEW SPEAKERS
Monitor-SE Series Owners Manual_090617.indd 5 2017-09-07 10:40 AM
www.paradigm.com
6
To prevent damage to your speakers, please read the following guidelines
before making any connections.
Amplifier Distortion—The #1 Culprit!
Amplifier distortion is the principle cause of speaker damage. When
listening at higher volume levels, your amplifier may run out of clean
power and begin to produce a distorted signal if levels are increased any
further. This will damage any brand of speaker very quickly. (See your
Authorized Paradigm Dealer for amplifier recommendations).
More Powerful Amplifiers are Safer
When choosing an amplifier, always select an amplifier with a power
rating greater than that of the speaker. Using a 100 Watts per
channel amplifier on a 50 Watts speaker allows the amplifier adequate
headroom in order to provide a distortion free signal. Conversely, using
a 40 Watts per channel amplifier on a 50 Watts speaker limits the
amplifier’s headroom. This causes the amplifier to enter its distortion
level much sooner, potentially damaging the speaker.
Volume Control
Do not be fooled by the Volume Control of your receiver/preamplifier. It
only adjusts listening level—it is not a “power-output” dial. The amount of
amplifier power actually used at a given Volume Control setting depends
solely on the nature of the music you are listening to. At a given Volume
Control setting a quiet section of music will use less amplifier power than a
loud section. With typical pop-rock, jazz or large scale classical music the
rated output power of many receivers/amplifiers is often reached when
the Volume Control is between the “11” and “1” o’clock settings (with
bass/ treble and loudness controls not used—otherwise rated power may
be reached at even lower Volume Control settings).
Remember, all amplifiers produce distortion when operated beyond
their rated output power. The resulting distortion will damage all
speakers! Exercise caution! If you listen at loud levels, be careful to
listen for the point of audible distortion—if the speakers begin to sound
distressed, turn the Volume Control down or your speakers and/or
amplifier(s) will be damaged! This type of damage constitutes abuse
and is not covered by the warranty. If louder volumes are desired,
obtain a more powerful amplifier.
PREVENTING SPEAKER DAMAGE
Monitor-SE Series Owners Manual_090617.indd 6 2017-09-07 10:40 AM
www.paradigm.com
7
There is a Limit!
Although more powerful amplifiers are safer, there is a point at which
you could have more power than the speaker can handle. At that point
you will overpower the speaker and damage it. Exercise caution! At loud
levels do not increase bass/treble controls from zero and ensure that
all loudness/ contour/bass EQ buttons are off (otherwise rated output
power will be reached at lower volume control settings). If you listen at
loud levels, watch for excessive visible cone excursion (grille movement)
from the woofer—then turn the Volume Control down.
The Right Amount of Power
A power-range rating is given as a guide to indicate the approximate
minimum and maximum power input of your Paradigm speakers. Amplifiers
that exceed your speaker’s power-range rating are recommended. Their
greater power reserves provide better sound. However, exercise caution!
Use the speakers within their power-range rating to prevent damage (keep
listening levels below the point of excessive woofer cone excursion).
PREVENTING SPEAKER DAMAGE
(cont’d)
Monitor-SE Series Owners Manual_090617.indd 7 2017-09-07 10:40 AM
www.paradigm.com
8
Paradigm Monitor SE Series speakers are designed to provide
exceptional sound in a wide variety of domestic settings. However, it
is important to note that listening room construction, dimensions and
furnishings all play a part in the quality of sound you will ultimately achieve.
Your listening room will impose its own character on the performance
capabilities of any speaker system. The extra care you take in correctly
positioning the speakers will result in greater listening enjoyment. Keep
the following guidelines in mind when deciding on the best speaker
placement:
Mid and high frequencies are affected by the amount of soft furnishings
in your room—curtains, carpets, sofas, wall coverings, etc. An excess
of such items can result in a somewhat dull sound. The same room
without any soft furnishings can produce an overall bright sound. The
typical quantity of soft furnishings found in most living environments
provides the right acoustic characteristics to allow the speakers to
sound balanced;
Concrete floors and walls tend to aggravate low-frequency standing
wave problems and are less preferred;
Rooms where height, width and length are similar should be
avoided as they can exhibit significant low-frequency standing wave
problems. This may result in reduced clarity. If no other room is possible,
experiment with speaker placement to minimize acoustic problems.
ROOM ACOUSTICS
Monitor-SE Series Owners Manual_090617.indd 8 2017-09-07 10:40 AM
www.paradigm.com
9
Ideal placement of front and center speakers
Monitor SE Series front speakers are designed to allow flexible placement
while providing a very large window of sound throughout your listening
room. To ensure the best performance possible we strongly recommend
that you observe the placement guidelines on the following pages
PLACEMENT:
Front Left & Right
Monitor-SE Series Owners Manual_090617.indd 9 2017-09-07 10:40 AM
www.paradigm.com
10
8” (20 cm)
8po (20 cm)
Accurate Timbre
For the most accurate and natural timbre, place front speakers so that
their high-frequency drivers are approximately at ear level, as shown.
Placing bookshelf models on Paradigm speaker stands (sold separately)
or bookshelves raises their high-frequency drivers to approximately ear
level, thereby ensuring the best performance possible.
Monitor-SE Series Owners Manual_090617.indd 10 2017-09-07 10:40 AM
www.paradigm.com
11
8” (20 cm)
8po (20 cm)
Balanced Bass
Placing front speakers in corners will over-emphasize bass and reduce
overall clarity. Avoid corner placement. Position front speakers 8 in (20 cm)
or more from the wall behind the speaker and as much as possible from
either side wall, as shown in. This will ensure better bass performance and
optimal midrange clarity.
Monitor-SE Series Owners Manual_090617.indd 11 2017-09-07 10:40 AM
www.paradigm.com
12
Optimal Imaging
Measure the distance from your main listening area to the front speakers
(“X”). For best imaging, place speakers from three-quarters of that
distance up to that same distance from each other (3/4 of “X” to “X”),
as shown. To further optimize imaging, toe speakers slightly inward so
they point toward the listening position with their axes crossing just behind
it, as shown.
Monitor-SE Series Owners Manual_090617.indd 12 2017-09-07 10:40 AM
www.paradigm.com
13
The Monitor SE Series center speaker is designed to cover a large,
wide listening area, allowing listeners throughout the room to hear center-
channel information with unprecedented clarity and intelligibility.
Placing your center-channel speaker below the TV will ensure the
best possible clarity and intelligibility. Position the speaker flush with
the front of the TV or speaker shelf to minimize unwanted sound
reflections. Make sure the center-channel speaker is approximately
the same distance away from the primary listening position as your
front speakers. (Some A/V receivers and processors can electronically
adjust for differences in distance.)
PLACEMENT:
The Center Speaker
Monitor-SE Series Owners Manual_090617.indd 13 2017-09-07 10:40 AM
www.paradigm.com
14
WIRING
MINIMUM GAUGE REQUIREMENTS
LENGTH
DIAMETER GAUGE
Under 4.5 m (15 ft)
Under 9 m (30 ft)
Over 9 m (30 ft)
1.3 mm (0.05 in)
1.6 mm (0.06 in)
2.0 mm (0.08 in)
16 awg
14 awg
12 awg
Turn your amplifier(s) OFF before connecting your
speakers. This will avoid damage which could
result from accidental shorting of speaker cables.
For optimum sound, the use of high quality speaker cable is essential.
The chart below identifies the minimum gauge requirements for various
lengths. See your Authorized Paradigm Dealer for recommendations.
Monitor-SE Series Owners Manual_090617.indd 14 2017-09-07 10:40 AM
www.paradigm.com
15
Your speakers’ binding posts can be used with banana, pin or spade
connectors, as well as with bare wire. Tighten the posts firmly by hand
but do not over tighten!
Correct polarity (or phase) is critical for proper soundstage imaging and
bass performance. Connect one speaker at a time to ensure proper
connection of every channel. The red (+) amplifier terminal must be
connected to the red (+) speaker terminal. The same applies to the black (–)
terminals. Make sure all wires are firmly fastened. Repeat this connection
procedure for each speaker in your system.
NOTE: If you hear a distinct lack of bass and a dislocated stereo image then
one or more of your speakers may be connected out of phase (polarity is
reversed). Re-check to ensure that each speakers’ cable is connected with
correct polarity: red (+) to red (+) and black (–) to black (–).
-+
SPEAKER CONNECTION
Monitor-SE Series Owners Manual_090617.indd 15 2017-09-07 10:40 AM
www.paradigm.com
16
Once you have your speakers positioned in the room and have set
speaker
distances and calibrated speaker levels through your Audio/Video
Processor or A/V Receiver it’s time for a little fine tuning.
Since Paradigm speakers provide exceptional performance in a variety of
room settings, fine tuning is simply a matter of making slight adjustments
(if necessary) to their placement in the room.
Start with the front speakers and listen to familiar music in stereo. The
soundstage will be both wide and deep, but this can be tuned to your
personal preference by adjusting the toe-in (the amount the speakers are
turned toward the listening area). More toe-in will increase image depth
and localization, less toe-in will increase image width. Adjust the toe-in in
small increments, listening each time, until you achieve the soundstage
balance you prefer. Toe-in is not applicable to the other speakers in your
system since their position and sound distribution pattern is fixed.
Fine tuning for center speakers is a matter of making volume level
adjustments that may be required for a particular multi-channel music
or movie program. If necessary, adjust your Audio/Video Processor’s
or A/V Receiver’s volume levels to ensure there is a cohesive overall
soundstage.
To fine tune surround/rear speakers, please follow the illustrations in the
earlier section.
To fine tune the subwoofer, please refer to the Owner’s Manual that was
included with your subwoofer.
FINE TUNING
Monitor-SE Series Owners Manual_090617.indd 16 2017-09-07 10:40 AM
www.paradigm.com
17
TROUBLESHOOTING GUIDE
No Sound
from One
or More
Speakers
Make sure receiver, preamp or amplifier
is plugged in and turned on. Check power
outlet at the wall is working. Are headphones
plugged in, or is system on Mute? Re-check
all connections.
Check your balance. Check that all power
cords are properly plugged in and functioning.
Swap a non-working speaker with one that
works to determine if the problem is with the
speaker or something else (i.e. wiring, amplifier).
One or more speakers may be connected out
of phase (their polarity is reversed). Re-check to
ensure that each speaker’s cable is connected
with correct polarity: red (+) to red (+) and black
(-) to black (-).
No Sound
Lack of
Bass or
Dislocated
Image
Monitor-SE Series Owners Manual_090617.indd 17 2017-09-07 10:40 AM
www.paradigm.com
18
Paradigm speakers covered in this manual are warranted to be and
remain free of manufacturing and/or material defects for a period of five
(5) years from the date of original purchase. Within the time period
specified, repair, replacement or adjustment of parts for manufacturing
and/or material defects will be free of charge to the original owner.
Thermal or mechanical abuse/misuse is not covered under the
Paradigm warranty.
Limitations:
Warranty begins on date of original retail purchase from an Authorized
Paradigm Dealer only. It is not transferable;
Warranty applies to product in normal home use only. If product is
subjected to any of the conditions outlined in the next section, warranty
is void;
Warranty does not apply if the product is used in professional or
commercial applications.
Warranty is Void if:
The product has been abused (intentionally or accidentally);
The product has been used in conjunction with unsuitable or faulty
equipment;
The product has been subjected to damaging signals, derangement
in transport, mechanical damage or any abnormal conditions;
The product (including cabinet) has been tampered with or damaged
by an unauthorized service facility;
The serial number has been removed or defaced.
Owner Responsibilities:
Provide normal/reasonable operating care and maintenance;
Provide or pay for transportation charges for product to service facility;
LIMITED WARRANTY
Monitor-SE Series Owners Manual_090617.indd 18 2017-09-07 10:40 AM
www.paradigm.com
19
Provide proof of purchase (your sales receipt given at time of purchase
from your Authorized Paradigm Dealer must be retained for proof-of-
purchase date).
Should servicing be required, contact your nearest Authorized Paradigm
Dealer, Paradigm Electronics Inc. or Import Distributor (outside the U.S.
and Canada) to arrange, bring in or ship prepaid, any defective unit. Visit
our website, www.paradigm.com for more information.
Paradigm Electronics Inc. reserves the right to improve the design of
any product without assuming any obligation to modify any product
previously manufactured.
This warranty is in lieu of all other warranties expressed or implied, of
merchantability, fitness for any particular purpose and may not be extended
or enlarged by anyone. In no event shall Paradigm Electronics Inc., their
agents or representatives be responsible for any incidental or consequential
damages. Some jurisdictions do not allow limitation of incidental or
consequential damages, so this exclusion may not apply to you.
Retain this manual and your sales receipt for proof of warranty term and
proof of purchase.
Monitor-SE Series Owners Manual_090617.indd 19 2017-09-07 10:40 AM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Paradigm Monitor SE Atom Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues