Panasonic PT40LC12K Mode d'emploi

Models No. PT-40LC12-K/PT-45LC12-K

LSQT0615A

Multi-Media Projection Display

Operating Instructions

2

Important Safety Instructions

This symbol warns the user

that uninsulated voltage within

the unit may have sufficient

magnitude to cause electric

shock.

Therefore, it is dangerous to

make any kind of contact with

any inside part of this unit.

This symbol alerts the user that

important literature concerning

the operation and maintenance

of this unit has been included.

Therefore, it should be read

carefully in order to avoid any

problems.

The pictorial representation of

a hot surface within a triangle

is intended to tell the user that

parts inside the product are a

risk of burns to persons.

Note to CATV System Installer: This reminder is provided to call the CATV system installer’s attention to Article

820–40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall

be connected to the grounding system of the building, as close to the point of cable entry as practical.

Important Safety Instructions For Projection display

WARNING: To reduce the risk of electric shock, do not remove cover or back. No

user-serviceable parts inside. Refer servicing to qualified service personnel.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

1. Read and apply the operating instructions provided with your projection display.

2. Read all of the instructions given here and retain them for later use.

3. Follow all warnings and instructions marked on the projection display.

4. Unplug this projection display from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a

damp cloth for cleaning.

5. Do not use attachments / accessories not recommended by the projection display manufacturer as they may cause

hazards.

6. Do not use this projection display near water. For example: Avoid placing it near a bathtub, washbowl, kitchen sink,

or laundry tub, in a wet basement, or near a swimming pool, etc.

7. Do not place this projection display on an unstable cart, stand or table. The projection display may fall,

causing serious injury to a child or adult, and serious damage to the appliance. Use only with a cart or

stand recommended by the manufacturer, or sold with the projection display.

7A. An appliance and cart combination shall be moved with care. Quick stops, excessive force, and uneven

surfaces may cause the appliance and cart combination to overturn.

8. Slots and openings in the cabinet and the back are provided for ventilation, to ensure reliable operation of the

projection display and to protect it from overheating. These openings must not be blocked or covered. There shall

be at least 10 cm of space from these openings. The openings shall never be blocked by placing the projection

display on a bed, sofa, rug or other similar surface. This projection display shall never be placed near or over a

radiator or heat register. This projection display shall not be placed in a built-in installation such as a bookcase

unless proper ventilation is provided.

9. Operate only from the type of power source indicated on the marking label. If you are not sure of the type of power

supplied to your home consult your television dealer or local power company.

10. This projection display is equipped with a polarized alternating-current line plug

(a plug having one blade wider than the other). This plug will fit into the power

outlet only one way. This is a safety feature. If you are unable to insert the plug

fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact

your electrician to replace your obsolete outlet. Do not defeat the safety purpose

of the polarized plug.

11. Do not allow anything to rest and to pinch on the power cord. Do not locate this

projection display where the power cord will walked on.

12. Do not overload wall outlets and extension cords as this can result in fire or electric shock.

13. Never push objects of any kind into this projection display through cabinet slots as they may touch dangerous

voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the

projection display.

3

Getting Started

Important Safety Instructions

14. If an outside antenna is connected to the television equipment, be sure the antenna system is grounded so as to

provide some protection against voltage surges and built up static charges. In the U.S.Selection 810 of the National

Electrical Code provides information with respect to proper grounding of the mast and supporting structure,

grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-

discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure.

15. For added protection for this projection display during a lightning storm, or when it is left unattended and unused for

long periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage to the

receiver due to lightning and power-line surges.

16. An outside antenna system shall not be located in the vicinity of overhead power lines or other electric light or

power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system

extreme care shall be taken to keep from touching such power lines or circuits as contact with them might be fatal.

17. Unplug this projection display from the wall outlet, and refer servicing to qualified service personnel under the

following conditions:

a. When the power cord or plug is damaged or frayed.

b. If liquid has been spilled into the projection display.

c. If the projection display has been exposed to rain or water.

d. If the projection display does not operate normally by following the operating instructions. Adjust only those

controls that are covered by the operating instructions as improper adjustment of other controls may result in

damage and will often require extensive work by a qualified technician to restore the projection display to normal

operation.

e. If the projection display has been dropped or the cabinet has been damaged.

f. When the projection display exhibits a distinct change in performance - this indicates a need for service.

18. Do not attempt to service this projection display yourself as opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

19. When replacement parts are required, be sure the service technician has used replacement parts specified by the

manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire,

electric shock, or other hazards.

20. Upon completion of any service or repairs to this projection display, ask the service technician to perform routine

safety checks to determine that the projection display is in safe operating condition.

21. WARNING: To prevent fire or shock hazard, do not expose this appliance to rain or moisture.

22. WARNING: Because the temperature of the lamp unit is elevated immediately after its use, directly touching it

may cause burns. After the lamp has cooled enough, replace the lamp unit.

23. CAUTION: To prevent electric shock, match wide blade of plug to wide slot of AC outlet and fully insert. Do not

use this (polarized) plug with a receptacle or other outlet unless the blade can be fully inserted to

prevent blade exposure.

Clean the air filter regularly. Not cleaning the air filter could shorten the life of the set.

The lamp has a maximum life of about 5 000 hours.

If use exceeds this figure, the possibility of lamp damage becomes greater.

The lamp should be changed as soon as possible once the lamp warning message appears.

If the lamp is damaged, please contact your nearest dealer.

When VIEWING MODE is set to CINEMA, brightness will be reduced, but the life of the LCD panel can be

prolonged. Therefore, the CINEMA setting is recommended when possible.

4

Welcome to the Panasonic family of customers. We hope that you will have many years of enjoyment

from your new projection television set.

To obtain maximum benefit from your set, please read these Instructions before making any adjustments, and

retain them for future reference.

Retain your purchase receipt also, and record the serial number of your set in the space provided on

the rear cover of these instructions.

Trademarks

• Licensed by BBE Sound, Inc. under USP4638258 and 4482866. BBE and BBE symbol are registered trademarks of BBE

Sound, Inc.

• VGA and XGA are trademarks of International Business Machines Corporation.

• Macintosh is a registered trademark of Apple Computer, USA.

• VESA and SVGA are trademarks of the Video Electronics Standard Association.

Even if no special notation has been made of company or product trademarks, these trademarks have been fully respected.

• Equipped with

®

-TV Noise Reduction for true MTS reproduction.

®

-TV Noise Reduction is required for good stereo

separation and audio fidelity.

®

is a registered trademark, and is licensed by

®

Technology Licensing.

Dear Panasonic Customer

5

Getting Started

Table of Contents

Cleaning the Air Filter ................................................................................................................ 62

Clogged Air Filter Detection .............................................................................................. 63

Air Filter Replacement ...................................................................................................... 63

Replacing the lamp unit............................................................................................................. 64

Remote Control Quick Reference Guide (Operating peripheral equipment)........................ 65

Troubleshooting ......................................................................................................................... 72

Cleaning ...................................................................................................................................... 73

Specifications ............................................................................................................................. 74

Limited Warranty / Servicentre List .......................................................................................... 75

Index .............................................................................................................................Back Cover

Important Safety Instructions ..................................................................................................... 2

Before Using ................................................................................................................................. 6

Receiver Location ...............................................................................................................6

Optional External Equipment .............................................................................................. 6

Safety Precaution ...............................................................................................................6

Viewing position .................................................................................................................. 6

Accessories ........................................................................................................................ 7

Remote Control Battery Installation .................................................................................... 7

Location of Controls .................................................................................................................... 8

Illuminated Remote Control ................................................................................................ 8

Controls and Terminals on the projection display ............................................................. 10

Installation .................................................................................................................................. 12

Connecting the Antenna/Cable to the RF In Terminal (No VCR) ...................................... 12

Connecting the Antenna/Cable to the RF In Terminal (VCR) ............................................ 14

How to connect the “1, 2, 3” Input Terminals .................................................................... 15

How to connect the COMPONENT VIDEO Input Terminals ............................................. 16

How to connect the AV Out Terminals .............................................................................. 17

How to connect the PC Input Terminals ............................................................................ 18

Analog RGB signals that can be input .............................................................................. 19

Adjusting screen position and size .......................................................................................... 40

Audio Adjustments .................................................................................................................... 42

Picture Adjustments .................................................................................................................. 44

Closed Captions ......................................................................................................................... 46

Lock Feature ............................................................................................................................... 48

Channel Caption Feature........................................................................................................... 55

Weak Signal Display Feature .................................................................................................... 56

Video NR (Noise Reduction) Feature ....................................................................................... 57

Automatically changing screen size ........................................................................................ 58

Setting when 480p signals (sequential scan) are

input through COMPONENT VIDEO INPUT ............................................................................. 59

RGB Input Feature ..................................................................................................................... 60

Switching languages for display .............................................................................................. 61

Information ................................................................................................................................. 61

TO

Start !

Use

Now !

Enjoy

more !

Other

Information !

Advanced Operation

Information

Power ON / OFF .......................................................................................................................... 20

Initial Setup ....................................................................................................................... 20

Turning the Power ON and OFF ....................................................................................... 21

Flow Chart of Main menu .......................................................................................................... 22

Tuning channels ......................................................................................................................... 24

Automatic channel setting ................................................................................................. 24

Manual channel setting ..................................................................................................... 26

Projection display operation ..................................................................................................... 28

TV Status display .............................................................................................................. 29

Using the number keys ..................................................................................................... 29

Using projection display Channel up/down buttons to select input mode ......................... 29

Auto shut off ...................................................................................................................... 29

Invalid operation notice feature......................................................................................... 29

ASPECT Controls ....................................................................................................................... 30

Searching for the desired channel (Channel search) .............................................................. 32

Playing peripheral equipment ................................................................................................... 33

Mute / Freeze / SAP .................................................................................................................... 34

Split screen ................................................................................................................................. 36

Picture in Picture (PIP) Screen .................................................................................................38

Getting Started

Basic Operation

6

Receiver Location

Locate for comfortable viewing. Avoid placing where sunlight or other bright light (including reflections) will fall on the

screen.

Use of some types of fluorescent lighting can reduce remote control transmitter range.

Adequate ventilation is essential to prevent internal component failure. Keep away from areas of excessive heat or

moisture.

Optional External Equipment

The Video / Audio connection between components can be made with shielded video and audio cables. For best

performance, video cables should utilize 75 Ω coaxial shielded cables. Cables are available from your dealer or

electronic supply house.

Before you purchase any cables, be sure you know what type of output and input connectors your various components

require. Also determine the length of cable you’ll need.

Safety Precaution

Please take safety precautions to prevent the unit from

falling over.

The unit may fall over during earthquakes, or if someone

stands on or shakes the projection display.

Fixing to a wall

Use a strong rope or a chain (not included) to fasten

the projection display firmly to a strong support such as

a wall or pillar.

Before Using

Viewing position

To optimize your viewing comfort, please follow the viewing guidelines shown in the diagrams below.

If viewing for an extended period of time, sit as far back from the screen as possible.

30°

1.5 m

70°

1.5 m

7

Getting Started

Accessories

Requires two AA batteries (supplied).

1.Turn the Transmitter face down.

Remove top cover by pressing

down on marking and sliding cover

off in the direction indicated.

2.Install the batteries as shown in the

battery compartment.

(Polarity + or – must match the

markings in the compartment).

3.Replace the cover and slide in

reverse until the lock snaps.

Precaution on battery use

Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter.

Observe the following precautions:

Whenever you remove the batteries, you may need to reset the remote control infrared codes. We recommend

that you record the code on page 66, prior to setting up the remote.

Helpful Hint:

For frequent remote control users, replace old batteries with Alkaline batteries for longer life.

1. Batteries should always be replaced as a pair. Always use new batteries when replacing the old set.

2. Do not mix battery types (example: “Zinc Carbon” with “Alkaline”).

3. Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries.

4. Battery replacement is necessary when the remote control acts sporadically or stops operating the projection display

set.

Two AA size

Remote Control Battery Installation

(1) Remote Control (EUR7603Z80)

(2) Batteries 2 “AA”

(3) RGB Cable (2 m) (LSJA0239-1 or LSJA0443)

(4) Accessory Air Filter (LSYC0239)

Before Using

Helpful Hint:

8

Number keys

When 6 is pressed, channel 6 is displayed in single screen. (P. 29)

Location of Controls

Illuminated Remote Control

POWER button

Press to turn the projection display ON or OFF. (P. 21)

MUTE button

Press this button to mute the sound. (P. 34)

Mode Selection buttons

Selects the operation mode for the remote control. (PP. 65-71)

DVD (Digital Versatile Disc) Mode Selection for

Remote Control

VCR Mode Selection for

Remote Control

TV Mode Selection for

Remote Control

Digital TV Mode Selection for

Remote Control

Aux Mode Selection for

Remote Control

Receiver / Amplifier Mode Selection for

Remote Control

Cable TV Mode Selection for

Remote Control

Digital Broadcasting Satellite for

Remote Control

R-TUNE button

Press to view previous channel or video mode.

BBE sound

ON/OFF

CH Search

FREEZESPLIT Function/

PIP SIZE

PIP ON/OFFPIP Move PIP/SPLIT SWAP

(P. 39) (P. 38) (PP. 36, 39) (P. 34) (PP. 37, 39)

(P. 32) (P. 43)

Function buttons

PIP/SPLIT

CH Up

(PP. 37, 39)

PIP/SPLIT

CH Down

(PP. 37, 39)

9

Getting Started

ASPECT button

Changes the screen size. (P. 30)

Light button

Lights all buttons. The selected mode button (TV, VCR, etc.) flashes.

TV/VIDEO button

This input mode changes each time this button is pressed. (P. 33)

Reduces

volume

Changes to the next channel up

Increase

volume

The screen below

is displayed for 5

seconds.

Changes to the

next channel

down

Returns to normal

viewing from the

MENU screen.

Previous before

item in MENU.

Location of Controls

SAP button

Changes the audio mode. (P. 35)

Display menu

Press the ACTION

button to display

Menu screen

Note:

This section describes TV mode only. For other modes, see pages 65-71.

21HC

CBA

LAMRON

OERETS

PAS

ONOM

When the Menu screen is displayed, (PP. 22, 23)

Moves

cursor to the

left during

menu mode.

Moves cursor upward

during menu mode.

Moves cursor

downward during

menu mode.

Moves cursor to the

right during menu

mode.

Sets the items.

(P. 29)

10

A

Open

Controls and Terminals on the projection display

< FRONT >

LAMP indicator

This indicator lights up when there

is a malfunction with the lamp unit.

(PP. 21, 64, 72)

TEMP indicator

This indicator lights up when

there is an abnormal

temperature in the unit.

(P. 72)

Remote Control Sensor

POWER button/

POWER indicator

(P. 21)

Lamp unit

(P. 64)

Speaker cover

Press the mark on

the center of the front

cover to open.

Volume up(+) / down(–) buttons

(P. 28)

Channel up / down buttons

(P. 29)

PC Input terminal

(P. 18)

Input 3 terminals

(P. 15)

Location of Controls

Phones jack

Connect an earphone/headphones

(not supplied) to the Phones jack.

Speaker cover

Air filter

(P. 62)

11

Getting Started

< REAR >

Component signal input terminals

(P. 16)

AV out terminals

(P. 17)

Input 1 terminals

(P. 15)

Input 2 terminals

(P. 15)

Location of Controls

VHF/UHF terminal

(PP. 12-14)

Vent

Note:

Make sure the vent is not clogged. (This could cause damage.)

12

Connecting the Antenna / Cable to the RF in Terminal (No VCR)

Antenna Connection

For proper reception of VHF / UHF channels, an external antenna is required. For best reception an outdoor

antenna is recommended.

UHF AntennaVHF Antenna

Mixer

RF

Coaxial Cable

VHF/UHF TERMINAL

ON THE BACK OF THE

PROJECTION DISPLAY

Installation

When using “Nut type” RF coaxial cables, tighten with fingers only. Overtightening may damage terminals.

WARNING

• Turn off the power supply for all components before making any connections.

• If the cables necessary for connecting a component to the system are not included with the component or available

as an option, you may need to fashion a cable to suit the component concerned.

• Read the instruction manual for each system component carefully before connecting it.

• If there is a lot of jitter in the video signal input from the video source, the picture on the screen may flicker. In this

case, it will be necessary to connect a TBC (time base corrector).

Notes on connections

13

Getting Started

Cable Connection

Use this configuration when connecting the projection display to a cable TV system.

Notes:

• Certain cable systems offset some channels to reduce interference or have Premium (scrambled) channels. A cable

converter box is required for proper reception. Check with your local Cable company for its compatibility require-

ments.

• For reception of cable channels (01 - 125) connect the cable supplied by your local cable company.

Antenna Mode must be set to CABLE. (P. 24)

Installation

CABLE BOX

INPUT OUTPUT

TERMINAL ON

THE BACK OF

THE CABLE BOX

In from cable

Connect the cable from the antenna

or cable system to the VHF/UHF

terminal on the back of the

Projection display..

In from cable

Or

14

Use this configuration when connecting the projection display to a cable TV system using VCR.

Notes:

• When the RF coaxial cable is connected to the projection display VHF/UHF terminal via a cable box or VCR, set the

TV channel to CH3 or CH4. This does not apply when signal is input from VIDEO INPUT.

Installation

Connecting the Antenna / Cable to the RF in Terminal (VCR)

Connect the cable from the Output terminal on the back

of the Cable Box or antenna/cable system to the

Antenna input terminal on the back of the VCR.

CABLE BOX

TO VCR

OUTPUT

S-VIDEO

VIDEO

L-AUDIO-R

TO VCR

INPUT OUTPUT

OUTPUT INPUT

VCR

TERMINAL ON

THE BACK OF

THE CABLE BOX

In from cable

Incoming Cable from

Antenna or Cable TV

System

Or

15

Getting Started

Installation

How to connect the “1, 2, 3” Input Terminals

Connects VCRs and other peripheral equipment

Similar connections are available at the INPUT 1, 2, 3 input terminals.

Notes:

• Similar connections are available at the INPUT 1, 2, 3 input terminals.

• Input 3 is located on the front of the unit.

• Select the desired VIDEO input position by pressing the TV/VIDEO button. (P. 33)

• When connecting video cables, priority is given to the S-Video cable when the S-Video input terminal and the video

input terminal are connected at the same time.

(S-VHS VCR)

Audio

OUT

Video

OUT

S-Video

OUT

RL

S-VIDEO

AUDIO

(VHS VCR)

VIDEO

AUDIO

Audio

OUT

Video

OUT

R

L

Similar connections are available at the INPUT 1, 2, 3 input terminals.

16

How to connect the COMPONENT VIDEO Input Terminals

Notes:

• Similar connections are available at the COMPONENT VIDEO INPUT 1, 2 Terminals.

• Select the desired COMPONENT VIDEO INPUT position by pressing the TV/VIDEO button. (P. 33)

• Component video signals that can be input are 480i, 480p, 720p, and 1080i.

Installation

Audio

OUT

P

B

YP

R

DVD(Y/P

B

/P

R

) OUT

LR

DVD Player

COMPONENT VIDEO

AUDIO

Because each Y, PB, and PR signal is input independently, the Component signal allows for more accurate color

reproduction.

The Component signal output terminal indication will differ according to the output device (Y, PB / Cb, PR / Cr). Please

read the operating instructions included with the output device.

17

Getting Started

Installation

How to connect the AV Out Terminals

The “AV Out” Terminals output the same signals as the main picture on the projection display screen and sound from

the speaker at that time, e.g. TV programs or signals from INPUT 1, 2, 3 terminals.

Notes:

• Never connect the VIDEO IN and OUT terminals to the same video recorder, as this could cause incorrect operation.

• Even if TV is in Split or PIP mode, OUT terminals only output the main picture and sound signals. A sub-picture,

including channel search, etc., will not be output.

• VIDEO OUT terminals will not output Y, PB, PR, or RGB signals.

• The S-Video OUT terminal outputs the same signal that is input from the S-Video IN terminal.

Recording Equipment

(VHS VCR)

VIDEO

AUDIO

Audio

IN

Video

IN

S-Video

IN

S-VIDEO

R

L

(A Stereo Amplifier and Speakers)

Stereo System

AUDIO

Or

18

How to connect the PC Input Terminals

Signal Names for D-SUB 15P Connector

Pin Layout for PC Input

Terminal

Notes:

• Some PC models cannot be connected to the set. A conversion adapter is required to use the RGB cable (D-SUB

15P) to connect a Macintosh computer to the set. There is no need to use an adapter for computers with PC / AT

compatible D-SUB 15P terminal.

• The computer shown in the illustration is for example purposes only. Additional equipment and cables shown are not

supplied with this set.

• The picture will become dark if an RGB signal with a vertical scanning frequency of 62 Hz is input. To obtain the

optimum picture quality with the projection display, a vertical scanning frequency of 60 Hz is recommended.

• Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified

frequency range.

• Select the desired RGB input position by pressing the TV/VIDEO button. (P. 33)

Installation

PC audio cable (M3 stereo mini pin)

Connect a cable which matches

the audio output terminal on the computer.

Conversion adapter (If necessary)

RGB cable (D-SUB 15P)

COMPUTER

Pin No. Signal name

1R

2G

3B

4NC

5NC

6 Ground for R

7 Ground for G

8 Ground for B

Pin No. Signal name

9NC

10 Ground

11 NC

12 NC

13 HD/CSYNC

14 VD

15 NC

1

678

3

9

45

10

15 14 13 12 11

2

NC: Not connected

19

Getting Started

Installation

Analog RGB signals that can be input

The table below lists the different types of analog RGB signals that can be input.

If a signal which differs greatly from any of the types listed below is input, the picture image may not be displayed

correctly, or a black background may be displayed. At this time, “signal” will flash in the on-screen display for about 5

seconds.

Notes:

• Input signals with a mark * are compressed, therefore, picture quality may be different than with not compressed

signals, due to digital processing.

• The front D-SUB15P connector can accept RGB (H-V sync separate) used with most of PC and RGB (sync on green)

used with older Macintosh etc. However, it is not guaranteed to display stable color when using RGB (sync on green).

• When used with an external video processor/scaler, it must have RGB (H-V sync separate) output.

Personal Computer Signals

DTV Format

Signals

Mode type

Signal data

No. of dots

(H x V)

Horizontal frequency

(kHz)

Vertical frequency

(Hz)

VGA400 (70 Hz) 640 X 400 31.47 70.08 VGA400 70Hz

VGA480 (60 Hz) 640 X 480 31.47 59.94 VGA 60Hz

Macintosh 13˝ 640 X 480 35.00 66.67 MAC 13

VESA400 (85 Hz) 640 X 400 37.86 85.08 VESA 85Hz

VESA480 (72 Hz) 640 X 480 37.86 72.81 VGA 72Hz

VESA480 (75 Hz) 640 X 480 37.50 75.00 VGA 75Hz

VESA480 (85 Hz) 640 X 480 43.27 85.01 VGA 85Hz

SVGA (56 Hz) 800 X 600 35.16 56.25 SVGA 56Hz

SVGA (60 Hz) 800 X 600 37.88 60.32 SVGA 60Hz

SVGA (72 Hz) 800 X 600 48.08 72.19 SVGA 72Hz

SVGA (75 Hz) 800 X 600 46.88 75.00 SVGA 75Hz

SVGA (85 Hz) 800 X 600 53.67 85.06 SVGA 85Hz

Macintosh 16″ 832 X 624 49.73 74.55 MAC 16

* XGA (60 Hz) 1 024 X 768 48.36 60.00 XGA 60Hz

* XGA (70 Hz) 1 024 X 768 56.48 70.07 XGA 70Hz

* XGA (75 Hz) 1 024 X 768 60.02 75.03 XGA 75Hz

* Macintosh 19″ 1 024 X 768 60.24 74.93 MAC 19

* XGA (85 Hz) 1 024 X 768 68.68 85.00 XGA 85Hz

480 i 664 X 485 15.73 29.97 480 i

480 p 720 X 483 31.47 59.94 480 p

720 p 1 280 X 720 45.00 60.00 720 p

*1080 i 1 920 X 1 080 33.75 30.00 1080 i

Information menu

display

20

Press the POWER button to turn the

projection display on.

(Refer to page 21 for “Turning the Power

ON and OFF”.)

1

GNIDEECORP TES OTUA HC

Automatic Channel Setting is performed.

Power ON and OFF

First, check the connection of the Plug to the Wall Outlet and the Antenna/Cable to the RF in Terminal.

(PP. 12-14.)

If using Cable Box, DSS Receiver, or VCR,

• Turn on Cable Box.

• Turn off DSS Receiver, or VCR.

Case 1

Case 2

When setup is complete, the lowest

channel picture appears.

If setup is incomplete, the following

screen appears. Check connection of

Antenna/Cable to the RF in Terminal,

then try Automatic Channel Setting

again. (PP. 24, 25)

Note:

When the unit is turned on for the first time, Automatic Channel Setting is performed.

Initial Setup

Note:

To cancel AUTO SET in progress, press the

SWAP button.

NIAGA YEK NOITCA SSERP

ANNETNA KCEHC ESAELP

NEHT NOITCENNOC ELBAC

DNUOF HC ON

La page charge ...

Panasonic PT40LC12K Mode d'emploi

Ce manuel convient également à

Panasonic PT40LC12K Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents