DeWalt 7103629 Manuel utilisateur

DH3028

Pressure Washer

Laveuse à pression

Lavadora a presión

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES

DE USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-877-FNA-GAS1 (1-877-362-4271)•www.dewaltpw.com

2

English

A. Panel assembly

B. Nozzle grommets

C. Professional spray gun

D. Wheel

E. Quick-connect

spray wand

F. Frame

G. Engine dipstick/oil plug

H. Engine switch

I. Starter grip

J. Engine

K. Throttle control lever

L. Choke control

M. Fuel valve lever

N. Gas cap

O. Handle assembly

P. High-pressure hose

Q. High-pressure pump

DH3028 PRESSURE WASHER

Engine

Refer to the engine instruction manual for location and

operation of other engine controls.

Pump Specications

Cat Pumps

®

* 3DNX Series

Oil Capacity: 8.5 Ounces (251 ml)

For best results, pump oil designed specifically

for pressure washers is recommended, as

these contain a rust inhibitor and an anti-

foaming agent. If this oil is not available, an

SAE 30W non-detergent oil may be used.

* Cat Pumps

®

is a registered trademark of Cat

Pumps.

FIG. 1

J

C

E

P

A

B

Q

N

F

O

D

H

G

K

L

M

I

3

English

Denitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to

these symbols.

DANGER: Indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which,

if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which,

if not avoided, may result in minor or moderate injury.

NOTICE: Indicates a practice not related to personal injury

which, if not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS

CONTACT US AT: www.dewaltpw.com or 1-877-FNA-GAS1

(1-877-362-4271).

Specications

MODEL WEIGHT HEIGHT WIDTH LENGTH PSI MAX* AVERAGE

OPERATING

PSI

GPM MAX* AVERAGE

OPERATING

GPM

ENGINE

DH3028 85 lbs

(38.5 kg)

26"

(66.0 cm)

22"

(55.0 cm)

36"

(91.0 cm)

3000

(21399 kPa)

2900

(20685 kPa)

2.8

(10.8 L/min)

2.7

(10.2 L/min)

HONDA

196 cc OHV

* Maximum PSI and GPM ratings determined in accordance with the Pressure Washers Manufacturers Association (PWMA)

standard PW101.

Important Safety Instructions

DANGER: Carbon Monoxide. Using an engine indoors can kill

you in minutes. Engine exhaust contains high levels of carbon

monoxide (CO), a poisonous gas you cannot see or smell. You

may be breathing CO even if you do not smell engine exhaust.

WARNING: This product and its exhaust contain chemicals

known to the State of California to cause cancer, and birth

defects and other reproductive harm.

 NEVER use an engine inside homes, garages, crawlspaces or

other partly enclosed areas. Deadly levels of carbon monoxide

can build up in these areas. Using a fan or opening windows and

doors does NOT supply enough fresh air.

 ONLY use outdoors and far away from open windows, doors and

vents. These openings can pull in engine exhaust.

 

home. ALWAYS

alarm in your house. Read and follow all directions for CO

alarm before using. If you feel sick, dizzy or weak at anytime,

move to fresh air immediately. See a doctor. You could have

carbon monoxide poisoning.

4

English

WARNING: Do not operate this unit until you read this instruction

manual and the engine instruction manual for safety, operation and

maintenance instructions.

WARNING: When using this product basic precautions should

always be followed, including the following:

1. Read all instructions before using the product.

2. To reduce the risk of injury, close supervision is necessary when

a product is used near children.

3. Know how to stop the product and bleed pressures quickly. Be

thoroughly familiar with the controls.

4. Stay alert–watch what you are doing.

5. Do not operate the product when fatigued or under the influence

of alcohol or drugs.

6. Keep operating area clear of all persons.

7. Do not overreach or stand on unstable support. Keep good

footing and balance at all times.

8. Follow the maintenance instructions speciﬁed in the manual.

DANGER: RISK OF INJECTION OR SEVERE INJURY. KEEP

CLEAR OF NOZZLE. DO NOT DIRECT DISCHARGE STREAM AT

PERSONS. THIS PRODUCT IS TO BE USED ONLY BY TRAINED

OPERATORS.

WARNING: This product may not be equipped with a spark-

arresting muffler. If the product is not equipped and will be used

around flam ma ble ma teri als or on land covered with materials such

as agricultural crops, forest, brush, grass or other similar items, then

an ap proved spark arrester must be installed and is legally required

in the state of California. It is a violation of California statutes

section 130050 and/or sec tions 4442 and 4443 of the California

Public Re sourc es Code, unless the engine is equipped with a spark

arrester, as defined in section 4442, and maintained in ef fec tive

work ing order. Spark arresters are also required on some U.S.

For est Service land and may also be legally required under other

statutes and or di nanc es.

WARNING: This product and its exhaust contain chemicals

known to the State of California to cause cancer, and birth

defects or other reproductive harm. In addition, some cleaning

products and dust contain chemicals known to the State of

California to cause cancer, and birth defects or other reproduc-

tive harm. Wash hands after handling.

Save theSe inStructionS

DANGER: RISK OF EXPLOSION OR FIRE

WHAT CAN HAPPEN HOW TO PREVENT IT

 • Spilledgasolineandit’s

vapors can be come ignited

from cigarette sparks,

electrical arcing, exhaust

gas es and hot engine

components such as

the muffler.

 • Shutoffengineandallow

it to cool before adding fuel

to the tank.

 • Usecareinfillingtankto

avoid spill ing fuel. Move

pressure wash er away

from fueling area before

start ing en gine.

 • Heatwillexpandfuelinthe

tank which could result in

spillage and pos si ble fire

explosion.

 • Keepmaximumfuellevel

1/2" (12.7 mm) be low

bottom of filler neck

to allow for expansion.

 • Operatingthepressure

washer in an ex plo sive

en viron ment could

re sult in a fire.

 • Operateandfuelequipment

in well-ven ti lat ed areas free

fromobstructions.Equip

areas with fire extinguisher

suit able for gas o line fires.

5

English

 • Materialsplacedagainstor

near the pressure washer

can in ter fere with its proper

ventilation fea tures caus ing

overheating and possible

ig ni tion of the materials.

 • Neveroperatepressure

wash er in an area

containing dry brush or

weeds.

 • Mufflerexhaustheatcan

damage paint ed sur fac es,

melt any material sen si tive

to heat (such as siding,

plas tic, rub ber, vinyl or the

pressure hose, itself), and

dam age live plants.

 • Alwayskeeppressure

washer a min i mum of 4'

(1.2 m) away from sur fac es

(such as houses, au to mo-

biles or live plants) that could

be damaged from muffler

exhaust heat.

 • Improperly stored fuel

could lead to acciden tal

ignition. Fuel im prop er ly

secured could get into the

hands of children or oth er

unqualifiedpersons.

 • StorefuelinanOSHA

approved con tain er, in a

se cure location away from

work area.

 • Useofacids,toxicor

cor ro sive chemicals,

poisons, in sec ti cides, or

any kind of flam ma ble

solvent with this product

could re sult in se ri ous

injury or death.

 • Donotsprayflammable

liquids.

DANGER: RISK TO BREATHING (ASPHYXIATION)

WHAT CAN HAPPEN HOW TO PREVENT IT

 • Breathingexhaustfumes

will cause se ri ous injury

or death! En gine exhaust

con tains carbon mon ox ide,

an odorless and deadly

gas.

 • Operatepressurewasherin

a well-ventilated area. Avoid

en closed areas such as

ga rag es, base ments, etc.

 • Neveroperateunitinor

near a lo ca tion occupied by

humans or animals.

 • Somecleaningfluids

con tain sub stanc es which

could cause injury to skin,

eyes or lungs.

 • Useonlycleaningfluids

spe cif i cal ly rec om mend ed

for high-pressure washers.

Fol low manufacturers

recommendations. Do not

use chlorine bleach or any

other corrosive compound.

6

English

 • Donotallowhoseto

contact muf fler.

 • Neverattachorremove

wand or hose fittings while

sys tem is pres sur ized.

 • Whenusingreplacement

lances or guns with this

pressure washer, DO NOT

use a lance and/or lance/

gun combination that is

shorter in length than

what was provided with

this pressure washer as

measured from the nozzle

end of the lance to the gun

trigger.

 • Injuriescanresultifsystem

pressure is not reduced

before attempting

maintenance or

disassembly.

 • Torelievesystempressure,

shut off engine, turn off

water sup ply and pull gun

trigger until water stops

flowing.

 • Use only accessories rated

equaltoorhigherthan

the rating of the pressure

washer.

DANGER: RISK OF FLUID INJECTION AND LACERATION

WHAT CAN HAPPEN HOW TO PREVENT IT

 • Yourpressurewasher

operates at fluid pressures

and velocities high enough

to penetrate human and

animal flesh, which could

result in amputation or

other serious injury. Leaks

caused by loose fittings or

worn or damaged hoses

can result in injection

injuries. DO NOT TREAT

FLUID INJECTION AS

A SIMPLE CUT! See a

physician immediately!

 • Inspectthehigh-pressure

hose regularly. Replace

the hose immediately if it is

damaged, worn, has melted

from contacting the engine,

or shows any signs of

cracks, bubbles, pinholes, or

other leakage. Never grasp

a high-pressure hose that

is leaking or damaged.

 • Nevertouch,graspor

attempt to cover a pinhole

or similar water leak on the

high-pressure hose. The

stream of water IS under

high pressure and WILL

penetrate skin.

 • Neverplacehandsinfront

of noz zle.

 • Directsprayawayfromself

and others.

 • Makesurehoseandfittings

are tight ened and in good

condition. Never hold onto

the hose or fittings during

op er a tion.

7

English

DANGER: RISK OF INJURY FROM SPRAY

WHAT CAN HAPPEN HOW TO PREVENT IT

 • High-velocityfluidspray

can cause objects to break,

propelling particles at high

speed.

 • AlwayswearANSI-

approved Z87.1 safety

glasses. Wear protective

clothing to protect against

accidental spraying.

 • Neverpointwandator

spray people or animals.

 • Lightorunsecuredobjects

can become hazardous

projectiles.

 • Alwayssecuretriggerlock

when wand is not in service

to prevent accidental

operation.

 • Neverpermanentlysecure

trigger in pull-back (open)

position.

DANGER: RISK OF UNSAFE OPERATION

WHAT CAN HAPPEN HOW TO PREVENT IT

 • Unsafeoperationofyour

pressure wash er could lead

to se ri ous in ju ry or death to

you or others.

 • Donotusechlorine

bleach or any other

corrosive compound.

 • Becomefamiliarwiththe

op er a tion and con trols of

the pressure washer.

 • Keepoperatingareaclear

of all persons, pets and

obstacles.

 • Donotoperatetheproduct

when fatigued or under

the influence of alcohol

or drugs. Stay alert at all

times.

 • Neverdefeatthesafety

fea tures of this prod uct.

 • Donotoperatemachine

with missing, broken or

un au tho rized parts.

 • Neverleavewand

unattended while unit

is running.

8

English

 • Ifproperstartingprocedure

is not followed, engine can

kickback causing serious

hand and arm injury.

 • Ifenginedoesnotstart

aftertwopulls,squeeze

trigger of gun to relieve

pump pressure. Pull starter

cord slowly until resistance

is felt. Then pull cord rapidly

to avoid kickback and

prevent hand or arm injury.

 • Thespraygun/wandis

a powerful clean ing tool

that could look like a toy

to a child.

 • Keepchildrenawayfrom

the pressure washer at all

times.

 • Reactiveforceofspray

will cause gun/wand to

kickback, and could cause

the op er a tor to slip or fall

or misdirect the spray.

Im prop er control of gun/

wand can re sult in

in ju ries to self and

others.

 • Donotoverreachorstand

on an unstable support.

 • Donotusepressure

washer while standing on a

ladder.

 • Gripgun/wandfirmlywith

both hands. Expect the

gun to kickback when

triggered.

DANGER: RISK OF INJURY OR PROP ER TY DAMAGE

WHEN TRANSPORTING OR STORING

WHAT CAN HAPPEN HOW TO PREVENT IT

 • Fueloroilcanleakorspill

and could result in fire or

breathing hazard. Se ri ous

in ju ry or death can re sult.

Fuel or oil leaks will dam age

carpet, paint or oth er

surfaces in ve hi cles

or trailers.

 • Oilcouldfillthecylinder

and damage the engine

if the unit is not stored or

transported in an upright

position.

 • Ifpressurewasheris

equippedwithafuelshut-

off valve, turn the valve to

the OFF position before

transporting to avoid fuel

leaks. If pres sure wash er

isnotequippedwithafuel

shut-off valve, drain the fuel

from tank before trans port-

ing. Only trans port fuel in an

OSHA-approved container.

Al ways place pressure

washer on a protective mat

when transporting to protect

against dam age to vehicle

from leaks.

Always transport and store

unit in an upright position.

Re move pres sure washer

from vehicle immediately

upon arrival at your

destination.

9

English

WARNING: RISK OF BURSTING

WHAT CAN HAPPEN HOW TO PREVENT IT

 • Over inflation of tires could

result in serious injury and

property damage.

 • Useatirepressuregauge

to check the tires pressure

before each use and while

inflating tires; see the tire

sidewall for the correct tire

pressure.

NOTE: Air tanks,

compressors and similar

equipmentusedtoinflate

tires can fill small tires

similar to these very rapidly.

Adjust pressure regulator

on air supply to no more

than the rating of the tire

pressure. Add air in small

incrementsandfrequently

use the tire gauge to prevent

over inflation.

 • High-velocityfluidspray

directed at pneumatic tire

sidewalls (such as found

on automobiles, trailers

and the like) could damage

the sidewall resulting in

serious injury.

 • Onpressurewashersrated

above 1600 psi (11032 kPa)

use the widest fan spray

(40º nozzle) and keep the

spray a minimum of 8"

(20 cm) from the pneumatic

tire sidewall. Do not aim

spray directly at the joint

between the tire and rim.

WARNING: RISK OF HOT SURFACES

WHAT CAN HAPPEN HOW TO PREVENT IT

 • Contactwithhotsurfaces,

such as engines exhaust

com po nents, could result in

se ri ous burn.

 • Duringoperation,touch

only the control surfaces

of the pres sure washer.

Keep children away from

the pres sure washer at all

times. They may not be able

to recognize the haz ards of

this product.

10

English

WARNING: RISK OF CHEMICAL BURN

WHAT CAN HAPPEN HOW TO PREVENT IT

 • Useofacids,toxicor

corrosive chemicals,

poisons, in sec ti cides, or any

kind of flam ma ble solvent

with this product could

re sult in se ri ous injury or

death.

 • Donotsprayacids,

gasoline, ker o sene, or any

other flammable materials

with this product. Use only

household de ter gents,

cleaners and degreasers

recommended for use with

pres sure washers.

 • Wearprotectiveclothing

to protect eyes and skin

from con tact with sprayed

materials.

WARNING: RISK OF

ELEC TRI CAL SHOCK

WHAT CAN HAPPEN HOW TO PREVENT IT

 • Spraydirectedatelectri-

cal outlets or switch es, or

ob jects con nect ed to an

elec tri cal circuit, could

re sult in a fatal electrical

shock.

 • Unpluganyelectrically

op er at ed product before

attempting to clean it. Direct

spray away from electric

out lets and switches.

WARNING: RISK OF

INJURY FROM LIFTING

WHAT CAN HAPPEN HOW TO PREVENT IT

 • Seriousinjurycanresult

from attempting to lift too

heavy an object.

 • Thepressurewasheristoo

heavy to be lifted by one

person. Obtain assistance

from others before lifting.

Save theSe inStructionS

For Future uSe

inStaLLation

Pressure Washer Assembly (Fig. 1)

1. Place handle assembly (O) onto frame, depress

F

O

the snap buttons, and slide the handle assembly

onto the frame (F) until snap buttons are secured

in place.

CAUTION: Risk of personal injury. Avoid placing

hands between handle and frame when assembling

to prevent pinching.

2. Attach high-pressure

E

P

hose (P) to spray gun.

Make sure it is

secure.

3. Connect wand (E) to

spray gun. Make sure

connection is secure.

11

English

NOTICE:       

pressure setting than the factory set pressure may damage pump.

3. Reduce the speed of the gasoline engine (RPM). Slow the

engine down and the water pressure will go down with it.

Spray Wand Nozzles (Fig. 1)

The nozzles for the spray wand are stored in the nozzle holder (B) on

the panel assembly (A). Colors on the panel identify nozzle location

and spray pattern. Refer to the following chart to choose the correct

nozzle for the job to be performed.

Nozzle Color Spray Pattern Uses Surfaces*

Red

0˚

powerful

pinpoint for

very intense

cleaning

metal or

concrete;

DO NOT use

on wood

Yellow

15˚

intense

cleaning of

small areas

metal, concrete

or wood

Green

25

˚

intense

cleaning of

larger areas

metal, concrete

or wood

White

40

˚

covers wide

areas of

cleaning

metal, concrete,

wood or vinyl

4. Place the nozzle holder (B) onto the panel assembly (A) and push

each nozzle holder into place.

5. Remove the five

B

A

colored quick-

connect nozzles from

the plastic bag and

insert them into

correct grommet on

the nozzle holder. Nozzles are color coded to match colored

nozzles on panel assembly.

NOTE: The high-pressure pump was filled with oil at the factory.

Always check oil level before using (refer to Maintenance for more

information).

WARNING: Risk of bursting.

Use a tire pressure gauge to check the

tires pressure before each use and while inflating tires; see the tire side-

wall for the correct tire pressure.

NOTE:Airtanks,compressorsandsimilarequipmentusedtoinflate

tires can fill small tires similar to these very rapidly. Adjust pressure

regulator on air supply to no more than the rating of the tire pressure.

Addairinsmallincrementsandfrequentlyusethe tire gauge to

prevent over inflation.

oPeration

Pressure Adjustments

The pressure setting is preset at the factory to achieve op ti mum

pres sure and cleaning. To lower the pres sure, follow these instruc-

tions.

1. Back away from the sur face to be cleaned. The further away you

are, the less the pressure will be on the surface to be cleaned.

2. Change to the 40˚ nozzle (white). This nozzle delivers a less

powerful stream of water and a wider spray pattern. Refer to

Spray Wand Nozzles.

12

English

Black

low pressure

applies cleaning

solutions

metal, concrete,

wood or vinyl

* NOTICE: The high-pressure spray from your pressure washer

is capable of causing damage to surfaces such as wood, glass,

automobile paint, auto striping and trim, delicate objects such

as flowers and shrubs. Before spraying, check the item to

be cleaned to assure yourself that it is strong enough to resist

damage from the force of spray.

CHANGING NOZZLES ON SPRAY WAND

DANGER: Risk of fluid injection. Do not direct discharge stream

toward persons, unprotected skin, eyes or any pets or animals.

Serious injury will occur.

WARNING: Flying objects could cause risk of serious injury. 

 attempt to change nozzles while pressure washer is running.

Turn engine off before changing nozzles.

 1.Pullquick-connectcouplerbackandinsert

nozzle.

 2.Release quick-connect coupler and

twist nozzle to make sure it is secure in

coupler.

WARNING: Flying object could cause risk



inserted in quick-connect socket and quick-

connect snap ring is fully engaged (forward)

before squeezing gun trigger.

Chemicals and Cleaning Solvents

Applying chemicals or cleaning solvents is a low-pressure operation.

NOTE: Use only soaps and chemicals designed for pressure washer

use. Do not use bleach.

TO APPLY CHEMICALS AND SOLVENTS

1. Press chemical hose (S) onto barbed fitting

S

located near high-pressure hose connection

of pump as shown.

2. Place the other end of chemical hose with

filter on it into the container holding chemi-

cal/cleaning solution.

NOTE: For every 10 gallons (38 liters) of

water pumped 1 gallon (3.8 liters) of chemi-

cal/cleaning solution will be used.

 3.Installlow-pressure(black)nozzleintoquick-connectfittingofspray

wand, refer to Spray Wand Nozzles.

NOTE: Chemicals and soaps

will not siphon if the black soap nozzle is not installed on the

spray wand.

4. After use of chemicals, place chemical hose into container of clean

water and draw clean water through chemical injection system

to rinse system thoroughly. If chemicals remain in the pump it

could be damaged. Pumps damaged due to chemicals will not be

covered under warranty.

Starting

WARNING: To reduce the risk of injury, read the pressure washer

instruction manual and the engine instruction manual before starting

pressure washer.

DANGER: Risk of fluid injection and laceration. When using the

high-pressure setting,   allow the high-pressure spray to

come in contact with unprotected skin, eyes, or with any pets or

animals. Serious injury will occur.

13

English

• Your washer operates at fluid pressures and velocities high

enough to penetrate human and animal flesh, which could result

in amputation or other serious injury. Leaks caused by loose fit-

tings or worn or damaged hoses can result in injection injuries.

DO NOT TREAT FLUID INJECTION AS A SIMPLE CUT! See a

physician immediately!

WARNING: Risk of fire, asphyxiation and burning. NEVER fill fuel

tank when engine is running or hot. Do not smoke when filling fuel

tank.

  fill fuel tank completely. Fill tank to 1/2" (12.7 mm) below

bottom of filler neck to provide space for fuel expansion. Wipe any

fuel spillage from engine and equipment before starting engine.

  run engine in doors or in en closed, poorly ven ti lat ed

      

and deadly gas.

           

muffler during or immediately after use of your pressure

washer. Damage to hoses from contact with hot engine



NOTICE: 

This could damage hose and/or pump inlet.

 

  turn water supply off while pressure washer engine is

running or damage to pump will result.

 

T

two minutes at a time. Pump operates in

bypass mode when spray gun trigger is not

pressed. When the temperature inside the

pump rises too high the thermal relief valve (T)

will open and release a gush of water in an

effort to lower the temperature inside the pump. The thermal

relief valve will then close. If pump is left in bypass mode for

more than two minutes internal components of the pump can

be damaged.

START-UP PROCEDURE

 1.Inawell-ventilatedoutdoorarea,addfresh,high-quality,unleaded

gasoline with a pump octane rating of 86 or higher. Do not overfill.

Wipe up spilled fuel before starting the engine. Refer to engine

instruction manual for correct procedure.

2. Check engine oil level. Refer to the engine instruction manual for

correct procedure.

3. Connect the water hose to the water source. Turn the water source

on to remove all air from the hose. When a steady stream of water

is present, turn the water source off.

4. Verify the filter screen (U) is in water inlet of pump.

U

The cone side faces out.

5. Connect the cold water source (V) to pump inlet.

NOTE: Water source must provide a minimum of

5 gallons per minute at 20 psi (138 kPa).

WARNING: To reduce the possibility of contami-

nation always protect against backflow when con-

nected to a potable water system.

6. Connect high-pressure hose (P) to pump

V

P

outlet.

7. If applying a chemical or cleaning solution,

refer to Chemicals and Cleaning Solvents.

8. Turn the water source on.

14

English

NOTICE: Risk of property damage. Failure to do so could cause

damage to the pump.

9. Remove all air from the pump and high-pressure hose by depress-

ing trigger until a steady stream of water is present.

10. Turn the engine ON/OFF switch (H) to the ON position.

11. Place the fuel valve lever (M) in the ON postion.

12.

If the engine is cold, move the choke (K) to the CLOSED position

as shown.

M

H

K

13. WARNING: Risk of unsafe operation. Pull starter grip slowly

until resistance is felt. Then pull starter grip (I, Fig. 1) rapidly to

avoid kickback and prevent hand or arm injury.

NOTE: Do not allow the starter grip to snap back. Return it gently

by hand.

WARNING: Risk of unsafe operation. If engine does not start

after two pulls, squeeze trigger of gun to relieve pump pressure. Pull

starter cord slowly until resistance is felt. Then pull cord rapidly to

avoid kickback and prevent hand or arm injury.

NOTE: If the oil level in the engine is low, the engine will not start.

If the engine does not start, check the oil level and add oil as

needed.

14. As the engine warms up, move the choke to

the OPEN position.

15. Depress trigger on gun to start water flow.

WARNING: Risk of unsafe operation. Stand

on a stable surface and grip gun/wand firmly with

       

triggered.

16. Release trigger to stop water flow.

DANGER:

X

trigger lock (X) when gun is not in use to prevent

accidental spraying.

17. Adjust spray for the task being performed

by changing quick connect nozzle. Refer to

Spray Wand Nozzles.

Shutting Down

1. If chemicals were applied, place the chemical hose into a

container of clean water and draw clean water through chemical

injection system to rinse system thoroughly.

NOTICE: Risk of property damage. Failure to do so could cause

damage to the pump.

2. Place the engine ON/OFF switch (H) to the OFF position.

3. Place the fuel valve lever (M) in the OFF

postion.

NOTICE: Risk of property damage.  turn

water supply off while pressure washer engine is

running or damage to pump will result.

4. Turn water source off.

5. Pull trigger on spray gun to relieve any water

pressure in hose or spray gun.

6. Refer to Storage for proper storage procedures.

15

English

Maintenance

WARNING: Risk of burning. When performing maintenance, you

may be exposed to hot surfaces, water pressure or moving parts that

can cause serious injury or death.

WARNING: Risk of fire. Always disconnect, spark plug wire, let

the engine cool and release all water pressure before performing

any maintenance or repair. The engine contains flammable fuel. Do

not smoke or work near open flames while performing maintenance.

To ensure efficient operation and longer life of your pressure washer,

a routine maintenance schedule should be prepared and followed.

If the pressure washer is used in unusual conditions, such as high

temperatures or dusty conditions, more frequent maintenance

checkswillberequired.

Engine

Consult the engine instruction manual for the man u fac tur er's recom-

mendations for any and all maintenance.

NOTE:Thepressurewasherframeisequippedwithanoildrain

hole to help make changing the engine oil easier.

Pump

NOTE: The pump was filled with oil at the factory. Change pump oil

after the first 50 hours of operation and every 300 hours thereafter,

or every 3 months. If using a 30W non-detergent oil, change oil every

150 hours thereafter.

TO CHECK OIL

The oil level should come to the dot in the middle

BB

CC

AA

of the sight glass (AA).

HOW TO CHANGE PUMP OIL

1. Loosen pump oil fill plug (BB).

2. Place a container under the oil drain plug

(CC).

3. Remove pump oil drain plug.

4. After oil is drained, replace oil drain plug.

Tighten securely.

5. Remove pump oil plug and fill with pump oil. An oil designed spe-

cifically for pressure washers is recommended as these contain a

rust inhibitor and an anit-foaming agent. If this oil is not available,

an SAE 30W non-detergent oil may be used.

6. Replace pump oil plug and tighten securely.

Nozzle Cleaning

If the nozzle becomes clogged with foreign materials, such as dirt,

excessive pressure may develop. If the nozzle becomes partially

clogged or restricted, the pump pressure will pulsate. Clean the

nozzle immediately using the nozzle kit supplied and the following

instructions:

1. Shut off the pressure washer and turn off the water supply.

2. Pull trigger on gun handle to relieve any water pressure.

3. Disconnect the spray wand from the gun.

4. Remove the high-pressure nozzle from the

Y

spray wand. Remove any obstructions

with the nozzle cleaning tool (Y) provided

and back flush with clean water.

16

English

5. Direct water supply into spray wand to

back flush loosened particles for 30

seconds.

6. Reassemble the nozzle to the wand.

7. Reconnect spray wand to gun then turn on water supply.

8. Start pressure washer and place spray wand into high-pressure

setting to test.

To Clean the Water Inlet Filter

This filter screen (U) should be checked periodically and cleaned if

necessary.

1. Remove the filter screen (U) by grasping the

U

end and removing it from water inlet of

pump.

2. Clean filter by flushing it with water on both

sides.

3. Reinsert filter into water inlet of pump. Cone

side faces out.

NOTE: Do not operate pressure washer without

ﬁlter properly installed.

To Remove Tires

1. Using a 1/8" hex head wrench loosen set

screw in hub collar.

2. Slide hub collar from axle and remove the

tire.

StoraGe

Engine

Consult the engine instruction manual for the man u fac tur er's

recommendations for storage.

Pump

The manufacturer recommends using a pump protector/winter-

izer, such as D

eWALT winterizer (DP80) when storing the unit

for more than 30 days and/or when freezing temperatures are

expected. D

eWALT winterizer (DP80) is availabe at the store

where the pressure washer was purchased. If a pump protector/

winterizer is not available, RV antifreeze can be used as outlined in

the following steps.

NOTE: Using a pump protector/ winterizer or RV antifreeze helps to

provide proper lubrication to the internal seals of the pump regard-

less of temperature or environment.

1. Obtain a funnel, 6 oz. (170 mL)

of RV antifreeze and 16–36"

(40–91cm) of garden hose with a

male hose connector attached to

one end.

NOTICE: Risk of property damage.

     

an ti freeze is corrosive and can dam-

age pump.

2. Disconnect spark plug wire.

3. Connect length of garden

hose to water inlet of pump.

4. Add RV antifreeze to hose as shown.

5. Pull engine starter rope slowly several times until an ti freeze

comes out of high-pressure hose con nec tion of pump.

6. Remove garden hose from water inlet of pump.

7. Reconnect spark plug wire.

17

English

Pressure Washer

1. Drain all water from high-

pressure hose, coil it and store it

in cradle of the pressure washer

handle.

2. With nozzle pointed down and

the spray gun and wand in a

vertical position, squeeze trigger

to drain all water from spray gun

and wand. Store in gun holder.

3. Store chemical hose so it is protected from dam age.

4. If space is needed, handles may be removed and attached as

shown.

CAUTION: Risk of personal injury. Avoid placing hands between

handle and frame when assembling to prevent pinching.

NOTICE: Risk of property damage. Always store and transport unit

in an upright position.

acceSSorieS

Recommended accessories for use with your tool are available for

purchase from your local dealer or authorized service center. If you

need assistance in locating any accessory for your tool, please con-

tact the FNA Group at www.dewaltpw.com, 1825 Greenleaf Avenue,

Elk Grove Village, Il 60007, or call (877) FNA-GAS1.

DANGER: Risk of fluid injection. When using replacement lances

or guns with this pressure washer,   use a lance and/or

lance/gun combination that is shorter in length than what was pro-

vided with this pressure washer as measured from the nozzle end

of the lance to the gun trigger.

WARNING: The use of any other accessory not recommended for

use with this tool could be hazardous. Use only accessories rated

equal to or higher than the rating of the pressure washer.

Service inForMation

Please have the following information available for all service calls:

Model Number ____________ Serial Number ___________

Date and Place of Purchase ____________________________

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance

and adjustment should be performed by a FNA factory service

center,aFNA authorizedservicecenteror otherqualified service

personnel. Always use identical replacement parts.

Limited Warranty

This pressure washer is warranted for three years from date of pur-

chase. We will repair, without charge, any defects due to faulty mate-

rials or workmanship. This warranty does not cover parts that are

damaged through misuse or abuse, or parts which must be replaced

from time to time due to normal pressure washer operation. Normal

wear parts include, but are not limited to, the engine air filter, spark

plug, pump valve seals and O rings. This warranty does not apply to

accessories or damage caused where repairs have been made or

attempted by a repair center not authorized by FNA. This warranty

gives you specific legal rights and you may have other rights which

vary in certain states or provinces. For further details of warranty

coverage and warranty repair information, visit www.dewaltpw.com

and click on Service and Support or call 1-877-FNA-GAS1 (1-877-

362-4271).

18

English

LATIN AMERICA: This warranty does not apply to products sold in

Latin America. For products sold in Latin America, see country spe-

cific warranty information contained either in the packaging, call the

local company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning labels

become illegible or are missing, call 1-877-FNA-GAS1 (1-877-362-

4271) for a free replacement.

Glossary

Bypass mode: Allows water to re-circulate within pump when the

gun trigger is not pulled.

Chemical hose: Feeds cleaning agents into the pump to mix with

the water. Refer to Chemicals and Cleaning Solvents.

Chemical injection system: Mixes cleaners or cleaning solvents

with water to improve cleaning effectiveness.

Choke control: Opens and closes carburetor choke valve.

CU: Cleaning Units. GPM multiplied by psi. (GPM x PSI = CU)

Fuel valve lever: Opens/closes connection between fuel tank and

carburetor.

GPM: Gallons Per Minute. The unit of measure for the flow rate of

water.

PSI:PoundsperSquareInch.Theunitofmeasureforwaterpres-

sure. Also used for air pressure, hydraulic pressure, etc.

kPa (kilopascal): Metricpressuremeasurement.1kilopascalequal

1000 pascals.

Quick-connect spray wand: Allowstheusertoquicklychangeout

high-pressure nozzles. Refer to Spray Wand Nozzles.

Thermal relief valve: When the temperature inside the pump rises

too high the valve will open and release a gush of water in an effort

to lower the temperature inside the pump. The valve will then close.

Water supply: All pressure washers must have a source of water.

Theminimumrequirementsforawatersupplyare20psi(138kPa)

and 5 gallons per minute.

19

English

Troubleshooting Guide

This section provides a list of the more frequently encountered malfunctions, their causes and corrective actions. The

operatorormaintenancepersonnelcanperformsomecorrectiveactions,andothersmayrequiretheassistanceofaqualifiedFNAtechni-

cian or your dealer.

Problem Code

Engine will not start ......................................................................................................1, 2, 3, 4, 5, 6, 7, 8, 36

(refer to the engine's instruction manual for further engine troubleshooting)

No or low pressure (initial use) ......................................................................................9, 10, 11, 12, 13, 14, 15, 16

Will not draw chemicals .................................................................................................16, 17, 18, 19, 20, 21

No or low pressure (after period of normal use) ...........................................................22, 23, 24

Water leaking at gun/spray wand connection ................................................................25, 26

Water leaking at pump ...................................................................................................25, 26, 27, 28

Oil leaking at pump ........................................................................................................29, 30, 31, 32, 33, 34, 35

Pump pulsates ...............................................................................................................12

Troubleshooting Codes

CODE POSSIBLE CAUSE POSSIBLE SOLUTION

1 No fuel. Add fuel.

2 Low oil. Addrequiredamountofoil.

3 Pressure builds up after two pulls on the recoil starter or after initial

use.

Squeezeguntriggertorelievepressure.

4 Choke lever in the NO CHOKE position. Move choke to the CHOKE po si tion.

5 Spark plug wire not attached. Attach spark plug wire.

6 Engine ON/OFF switch in OFF po si tion. Place engine ON/OFF switch in ON position.

7 Choke lever in the CHOKE position on a hot engine or an engine

that has been exposed to thermal heat for a long period of time.

Move choke to the NO CHOKE po si tion.

8 Fuel valve closed. Move the fuel valve lever to the OPEN position.

20

English

(Troubleshooting Codes cont.)

CODE POSSIBLE CAUSE POSSIBLE SOLUTION

9 Spray wand not in high pressure. See Spray Wand Nozzles under .

10 Low water supply. Water supply must be at least 5 GPM @

20 psi (138 kPa)

.

11 Leak at high-pressure hose fitting. Repair leak. Apply sealant tape if necessary.

12 Nozzle obstructed. See Nozzle Cleaning under Maintenance.

13 Water filter screen clogged. Remove and clean filter.

14 Air in hose. Turn off the engine, then the water source. Disconnect the

water source from the pump inlet and turn the water source

on to remove all air from the hose. When there is a steady

stream of water present, turn water source off. Recon nect

watersourcetopumpinletandturnonwatersource.Squeeze

trigger to re move re main ing air.

15 Choke lever in the CHOKE position. Move choke to the NO CHOKE po si tion.

16 High-pressure hose is too long. Use high-pressure hose under 100 feet (30.48 m). Lengthen water

supply hose instead of high-pressure hose.

17 Spray wand not in low pressure. See Spray Wand Nozzles under .

18 Chemical filter clogged. Clean filter.

19 Chemical screen not in cleaning solution. Make sure end of chemical hose is fully submerged into cleaning

solution.

20 Chemical too thick. Dilute chemical. Chemical should be the same consistency as water.

21 Worn seal or packing. Have parts cleaned or replaced by authorized service center.

22 Chemical build up in chemical injector. Have replaced by an authorized service center.

23 Worn or obstructed valves. Have replaced by authorized service center.

24 Worn unloader piston. Have replaced by authorized service center.

25 Worn or broken O-ring. Check and replace.

26 Loose hose connection. Tighten.

27 Piston packings worn. Have replaced by authorized service center.

28 Pump head or tubes damaged from freezing. Have replaced by authorized service center.

29 Oil seals worn. Have replaced by authorized service center

La page charge ...

DeWalt 7103629 Manuel utilisateur

Ce manuel convient également à

DeWalt 7103629 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents