DeWalt 7103629 Manuel utilisateur

Catégorie
Nettoyeurs haute pression
Taper
Manuel utilisateur

Ce manuel convient également à

DH3028
Pressure Washer
Laveuse à pression
Lavadora a presión
INSTRUCTION MANUAL
GUIDE D'UTILISATION
MANUAL DE INSTRUCCIONES
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA
DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES
DE USAR EL PRODUCTO.
If you have questions or comments, contact us.
Pour toute question ou tout commentaire, nous contacter.
Si tiene dudas o comentarios, contáctenos.
1-877-FNA-GAS1 (1-877-362-4271)•www.dewaltpw.com
2
English
A. Panel assembly
B. Nozzle grommets
C. Professional spray gun
D. Wheel
E. Quick-connect
spray wand
F. Frame
G. Engine dipstick/oil plug
H. Engine switch
I. Starter grip
J. Engine
K. Throttle control lever
L. Choke control
M. Fuel valve lever
N. Gas cap
O. Handle assembly
P. High-pressure hose
Q. High-pressure pump
DH3028 PRESSURE WASHER
Engine
Refer to the engine instruction manual for location and
operation of other engine controls.
Pump Specications
Cat Pumps
®
* 3DNX Series
Oil Capacity: 8.5 Ounces (251 ml)
For best results, pump oil designed specifically
for pressure washers is recommended, as
these contain a rust inhibitor and an anti-
foaming agent. If this oil is not available, an
SAE 30W non-detergent oil may be used.
* Cat Pumps
®
is a registered trademark of Cat
Pumps.
FIG. 1
J
C
E
P
A
B
Q
N
F
O
D
H
G
K
L
M
I
3
English
Denitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
these symbols.
DANGER: Indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
WARNING: Indicates a potentially hazardous situation which,
if not avoided, could result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which,
if not avoided, may result in minor or moderate injury.
NOTICE: Indicates a practice not related to personal injury
which, if not avoided, may result in property damage.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS
CONTACT US AT: www.dewaltpw.com or 1-877-FNA-GAS1
(1-877-362-4271).
Specications
MODEL WEIGHT HEIGHT WIDTH LENGTH PSI MAX* AVERAGE
OPERATING
PSI
GPM MAX* AVERAGE
OPERATING
GPM
ENGINE
DH3028 85 lbs
(38.5 kg)
26"
(66.0 cm)
22"
(55.0 cm)
36"
(91.0 cm)
3000
(21399 kPa)
2900
(20685 kPa)
2.8
(10.8 L/min)
2.7
(10.2 L/min)
HONDA
196 cc OHV
* Maximum PSI and GPM ratings determined in accordance with the Pressure Washers Manufacturers Association (PWMA)
standard PW101.
Important Safety Instructions
DANGER: Carbon Monoxide. Using an engine indoors can kill
you in minutes. Engine exhaust contains high levels of carbon
monoxide (CO), a poisonous gas you cannot see or smell. You
may be breathing CO even if you do not smell engine exhaust.
WARNING: This product and its exhaust contain chemicals
known to the State of California to cause cancer, and birth
defects and other reproductive harm.
 NEVER use an engine inside homes, garages, crawlspaces or
other partly enclosed areas. Deadly levels of carbon monoxide
can build up in these areas. Using a fan or opening windows and
doors does NOT supply enough fresh air.
 ONLY use outdoors and far away from open windows, doors and
vents. These openings can pull in engine exhaust.
 
home. ALWAYS
alarm in your house. Read and follow all directions for CO
alarm before using. If you feel sick, dizzy or weak at anytime,
move to fresh air immediately. See a doctor. You could have
carbon monoxide poisoning.
4
English
WARNING: Do not operate this unit until you read this instruction
manual and the engine instruction manual for safety, operation and
maintenance instructions.
WARNING: When using this product basic precautions should
always be followed, including the following:
1. Read all instructions before using the product.
2. To reduce the risk of injury, close supervision is necessary when
a product is used near children.
3. Know how to stop the product and bleed pressures quickly. Be
thoroughly familiar with the controls.
4. Stay alert–watch what you are doing.
5. Do not operate the product when fatigued or under the influence
of alcohol or drugs.
6. Keep operating area clear of all persons.
7. Do not overreach or stand on unstable support. Keep good
footing and balance at all times.
8. Follow the maintenance instructions specified in the manual.
DANGER: RISK OF INJECTION OR SEVERE INJURY. KEEP
CLEAR OF NOZZLE. DO NOT DIRECT DISCHARGE STREAM AT
PERSONS. THIS PRODUCT IS TO BE USED ONLY BY TRAINED
OPERATORS.
WARNING: This product may not be equipped with a spark-
arresting muffler. If the product is not equipped and will be used
around flam ma ble ma teri als or on land covered with materials such
as agricultural crops, forest, brush, grass or other similar items, then
an ap proved spark arrester must be installed and is legally required
in the state of California. It is a violation of California statutes
section 130050 and/or sec tions 4442 and 4443 of the California
Public Re sourc es Code, unless the engine is equipped with a spark
arrester, as defined in section 4442, and maintained in ef fec tive
work ing order. Spark arresters are also required on some U.S.
For est Service land and may also be legally required under other
statutes and or di nanc es.
WARNING: This product and its exhaust contain chemicals
known to the State of California to cause cancer, and birth
defects or other reproductive harm. In addition, some cleaning
products and dust contain chemicals known to the State of
California to cause cancer, and birth defects or other reproduc-
tive harm. Wash hands after handling.
Save theSe inStructionS
DANGER: RISK OF EXPLOSION OR FIRE
WHAT CAN HAPPEN HOW TO PREVENT IT
• Spilledgasolineandit’s
vapors can be come ignited
from cigarette sparks,
electrical arcing, exhaust
gas es and hot engine
components such as
the muffler.
• Shutoffengineandallow
it to cool before adding fuel
to the tank.
• Usecareinfillingtankto
avoid spill ing fuel. Move
pressure wash er away
from fueling area before
start ing en gine.
• Heatwillexpandfuelinthe
tank which could result in
spillage and pos si ble fire
explosion.
• Keepmaximumfuellevel
1/2" (12.7 mm) be low
bottom of filler neck
to allow for expansion.
• Operatingthepressure
washer in an ex plo sive
en viron ment could
re sult in a fire.
• Operateandfuelequipment
in well-ven ti lat ed areas free
fromobstructions.Equip
areas with fire extinguisher
suit able for gas o line fires.
5
English
• Materialsplacedagainstor
near the pressure washer
can in ter fere with its proper
ventilation fea tures caus ing
overheating and possible
ig ni tion of the materials.
• Neveroperatepressure
wash er in an area
containing dry brush or
weeds.
• Mufflerexhaustheatcan
damage paint ed sur fac es,
melt any material sen si tive
to heat (such as siding,
plas tic, rub ber, vinyl or the
pressure hose, itself), and
dam age live plants.
• Alwayskeeppressure
washer a min i mum of 4'
(1.2 m) away from sur fac es
(such as houses, au to mo-
biles or live plants) that could
be damaged from muffler
exhaust heat.
• Improperly stored fuel
could lead to acciden tal
ignition. Fuel im prop er ly
secured could get into the
hands of children or oth er
unqualifiedpersons.
• StorefuelinanOSHA
approved con tain er, in a
se cure location away from
work area.
• Useofacids,toxicor
cor ro sive chemicals,
poisons, in sec ti cides, or
any kind of flam ma ble
solvent with this product
could re sult in se ri ous
injury or death.
• Donotsprayflammable
liquids.
DANGER: RISK TO BREATHING (ASPHYXIATION)
WHAT CAN HAPPEN HOW TO PREVENT IT
• Breathingexhaustfumes
will cause se ri ous injury
or death! En gine exhaust
con tains carbon mon ox ide,
an odorless and deadly
gas.
• Operatepressurewasherin
a well-ventilated area. Avoid
en closed areas such as
ga rag es, base ments, etc.
• Neveroperateunitinor
near a lo ca tion occupied by
humans or animals.
• Somecleaningfluids
con tain sub stanc es which
could cause injury to skin,
eyes or lungs.
• Useonlycleaningfluids
spe cif i cal ly rec om mend ed
for high-pressure washers.
Fol low manufacturers
recommendations. Do not
use chlorine bleach or any
other corrosive compound.
6
English
• Donotallowhoseto
contact muf fler.
• Neverattachorremove
wand or hose fittings while
sys tem is pres sur ized.
• Whenusingreplacement
lances or guns with this
pressure washer, DO NOT
use a lance and/or lance/
gun combination that is
shorter in length than
what was provided with
this pressure washer as
measured from the nozzle
end of the lance to the gun
trigger.
• Injuriescanresultifsystem
pressure is not reduced
before attempting
maintenance or
disassembly.
• Torelievesystempressure,
shut off engine, turn off
water sup ply and pull gun
trigger until water stops
flowing.
• Use only accessories rated
equaltoorhigherthan
the rating of the pressure
washer.
DANGER: RISK OF FLUID INJECTION AND LACERATION
WHAT CAN HAPPEN HOW TO PREVENT IT
• Yourpressurewasher
operates at fluid pressures
and velocities high enough
to penetrate human and
animal flesh, which could
result in amputation or
other serious injury. Leaks
caused by loose fittings or
worn or damaged hoses
can result in injection
injuries. DO NOT TREAT
FLUID INJECTION AS
A SIMPLE CUT! See a
physician immediately!
• Inspectthehigh-pressure
hose regularly. Replace
the hose immediately if it is
damaged, worn, has melted
from contacting the engine,
or shows any signs of
cracks, bubbles, pinholes, or
other leakage. Never grasp
a high-pressure hose that
is leaking or damaged.
• Nevertouch,graspor
attempt to cover a pinhole
or similar water leak on the
high-pressure hose. The
stream of water IS under
high pressure and WILL
penetrate skin.
• Neverplacehandsinfront
of noz zle.
• Directsprayawayfromself
and others.
• Makesurehoseandfittings
are tight ened and in good
condition. Never hold onto
the hose or fittings during
op er a tion.
7
English
DANGER: RISK OF INJURY FROM SPRAY
WHAT CAN HAPPEN HOW TO PREVENT IT
• High-velocityfluidspray
can cause objects to break,
propelling particles at high
speed.
• AlwayswearANSI-
approved Z87.1 safety
glasses. Wear protective
clothing to protect against
accidental spraying.
• Neverpointwandator
spray people or animals.
• Lightorunsecuredobjects
can become hazardous
projectiles.
• Alwayssecuretriggerlock
when wand is not in service
to prevent accidental
operation.
• Neverpermanentlysecure
trigger in pull-back (open)
position.
DANGER: RISK OF UNSAFE OPERATION
WHAT CAN HAPPEN HOW TO PREVENT IT
• Unsafeoperationofyour
pressure wash er could lead
to se ri ous in ju ry or death to
you or others.
• Donotusechlorine
bleach or any other
corrosive compound.
• Becomefamiliarwiththe
op er a tion and con trols of
the pressure washer.
• Keepoperatingareaclear
of all persons, pets and
obstacles.
• Donotoperatetheproduct
when fatigued or under
the influence of alcohol
or drugs. Stay alert at all
times.
• Neverdefeatthesafety
fea tures of this prod uct.
• Donotoperatemachine
with missing, broken or
un au tho rized parts.
• Neverleavewand
unattended while unit
is running.
8
English
• Ifproperstartingprocedure
is not followed, engine can
kickback causing serious
hand and arm injury.
• Ifenginedoesnotstart
aftertwopulls,squeeze
trigger of gun to relieve
pump pressure. Pull starter
cord slowly until resistance
is felt. Then pull cord rapidly
to avoid kickback and
prevent hand or arm injury.
• Thespraygun/wandis
a powerful clean ing tool
that could look like a toy
to a child.
• Keepchildrenawayfrom
the pressure washer at all
times.
• Reactiveforceofspray
will cause gun/wand to
kickback, and could cause
the op er a tor to slip or fall
or misdirect the spray.
Im prop er control of gun/
wand can re sult in
in ju ries to self and
others.
• Donotoverreachorstand
on an unstable support.
• Donotusepressure
washer while standing on a
ladder.
• Gripgun/wandfirmlywith
both hands. Expect the
gun to kickback when
triggered.
DANGER: RISK OF INJURY OR PROP ER TY DAMAGE
WHEN TRANSPORTING OR STORING
WHAT CAN HAPPEN HOW TO PREVENT IT
• Fueloroilcanleakorspill
and could result in fire or
breathing hazard. Se ri ous
in ju ry or death can re sult.
Fuel or oil leaks will dam age
carpet, paint or oth er
surfaces in ve hi cles
or trailers.
• Oilcouldfillthecylinder
and damage the engine
if the unit is not stored or
transported in an upright
position.
• Ifpressurewasheris
equippedwithafuelshut-
off valve, turn the valve to
the OFF position before
transporting to avoid fuel
leaks. If pres sure wash er
isnotequippedwithafuel
shut-off valve, drain the fuel
from tank before trans port-
ing. Only trans port fuel in an
OSHA-approved container.
Al ways place pressure
washer on a protective mat
when transporting to protect
against dam age to vehicle
from leaks.
Always transport and store
unit in an upright position.
Re move pres sure washer
from vehicle immediately
upon arrival at your
destination.
9
English
WARNING: RISK OF BURSTING
WHAT CAN HAPPEN HOW TO PREVENT IT
• Over inflation of tires could
result in serious injury and
property damage.
• Useatirepressuregauge
to check the tires pressure
before each use and while
inflating tires; see the tire
sidewall for the correct tire
pressure.
NOTE: Air tanks,
compressors and similar
equipmentusedtoinflate
tires can fill small tires
similar to these very rapidly.
Adjust pressure regulator
on air supply to no more
than the rating of the tire
pressure. Add air in small
incrementsandfrequently
use the tire gauge to prevent
over inflation.
• High-velocityfluidspray
directed at pneumatic tire
sidewalls (such as found
on automobiles, trailers
and the like) could damage
the sidewall resulting in
serious injury.
• Onpressurewashersrated
above 1600 psi (11032 kPa)
use the widest fan spray
(40º nozzle) and keep the
spray a minimum of 8"
(20 cm) from the pneumatic
tire sidewall. Do not aim
spray directly at the joint
between the tire and rim.
WARNING: RISK OF HOT SURFACES
WHAT CAN HAPPEN HOW TO PREVENT IT
• Contactwithhotsurfaces,
such as engines exhaust
com po nents, could result in
se ri ous burn.
• Duringoperation,touch
only the control surfaces
of the pres sure washer.
Keep children away from
the pres sure washer at all
times. They may not be able
to recognize the haz ards of
this product.
10
English
WARNING: RISK OF CHEMICAL BURN
WHAT CAN HAPPEN HOW TO PREVENT IT
• Useofacids,toxicor
corrosive chemicals,
poisons, in sec ti cides, or any
kind of flam ma ble solvent
with this product could
re sult in se ri ous injury or
death.
• Donotsprayacids,
gasoline, ker o sene, or any
other flammable materials
with this product. Use only
household de ter gents,
cleaners and degreasers
recommended for use with
pres sure washers.
• Wearprotectiveclothing
to protect eyes and skin
from con tact with sprayed
materials.
WARNING: RISK OF
ELEC TRI CAL SHOCK
WHAT CAN HAPPEN HOW TO PREVENT IT
• Spraydirectedatelectri-
cal outlets or switch es, or
ob jects con nect ed to an
elec tri cal circuit, could
re sult in a fatal electrical
shock.
• Unpluganyelectrically
op er at ed product before
attempting to clean it. Direct
spray away from electric
out lets and switches.
WARNING: RISK OF
INJURY FROM LIFTING
WHAT CAN HAPPEN HOW TO PREVENT IT
• Seriousinjurycanresult
from attempting to lift too
heavy an object.
• Thepressurewasheristoo
heavy to be lifted by one
person. Obtain assistance
from others before lifting.
Save theSe inStructionS
For Future uSe
inStaLLation
Pressure Washer Assembly (Fig. 1)
1. Place handle assembly (O) onto frame, depress
F
O
the snap buttons, and slide the handle assembly
onto the frame (F) until snap buttons are secured
in place.
CAUTION: Risk of personal injury. Avoid placing
hands between handle and frame when assembling
to prevent pinching.
2. Attach high-pressure
E
P
hose (P) to spray gun.
Make sure it is
secure.
3. Connect wand (E) to
spray gun. Make sure
connection is secure.
11
English
NOTICE:       
pressure setting than the factory set pressure may damage pump.
3. Reduce the speed of the gasoline engine (RPM). Slow the
engine down and the water pressure will go down with it.
Spray Wand Nozzles (Fig. 1)
The nozzles for the spray wand are stored in the nozzle holder (B) on
the panel assembly (A). Colors on the panel identify nozzle location
and spray pattern. Refer to the following chart to choose the correct
nozzle for the job to be performed.
Nozzle Color Spray Pattern Uses Surfaces*
Red
powerful
pinpoint for
very intense
cleaning
metal or
concrete;
DO NOT use
on wood
Yellow
15˚
intense
cleaning of
small areas
metal, concrete
or wood
Green
25
˚
intense
cleaning of
larger areas
metal, concrete
or wood
White
40
˚
covers wide
areas of
cleaning
metal, concrete,
wood or vinyl
4. Place the nozzle holder (B) onto the panel assembly (A) and push
each nozzle holder into place.
5. Remove the five
B
A
colored quick-
connect nozzles from
the plastic bag and
insert them into
correct grommet on
the nozzle holder. Nozzles are color coded to match colored
nozzles on panel assembly.
NOTE: The high-pressure pump was filled with oil at the factory.
Always check oil level before using (refer to Maintenance for more
information).
WARNING: Risk of bursting.
Use a tire pressure gauge to check the
tires pressure before each use and while inflating tires; see the tire side-
wall for the correct tire pressure.
NOTE:Airtanks,compressorsandsimilarequipmentusedtoinflate
tires can fill small tires similar to these very rapidly. Adjust pressure
regulator on air supply to no more than the rating of the tire pressure.
Addairinsmallincrementsandfrequentlyusethe tire gauge to
prevent over inflation.
oPeration
Pressure Adjustments
The pressure setting is preset at the factory to achieve op ti mum
pres sure and cleaning. To lower the pres sure, follow these instruc-
tions.
1. Back away from the sur face to be cleaned. The further away you
are, the less the pressure will be on the surface to be cleaned.
2. Change to the 40˚ nozzle (white). This nozzle delivers a less
powerful stream of water and a wider spray pattern. Refer to
Spray Wand Nozzles.
12
English
Black
low pressure
applies cleaning
solutions
metal, concrete,
wood or vinyl
* NOTICE: The high-pressure spray from your pressure washer
is capable of causing damage to surfaces such as wood, glass,
automobile paint, auto striping and trim, delicate objects such
as flowers and shrubs. Before spraying, check the item to
be cleaned to assure yourself that it is strong enough to resist
damage from the force of spray.
CHANGING NOZZLES ON SPRAY WAND
DANGER: Risk of fluid injection. Do not direct discharge stream
toward persons, unprotected skin, eyes or any pets or animals.
Serious injury will occur.
WARNING: Flying objects could cause risk of serious injury. 
 attempt to change nozzles while pressure washer is running.
Turn engine off before changing nozzles.
1.Pullquick-connectcouplerbackandinsert
nozzle.
2.Release quick-connect coupler and
twist nozzle to make sure it is secure in
coupler.
WARNING: Flying object could cause risk

inserted in quick-connect socket and quick-
connect snap ring is fully engaged (forward)
before squeezing gun trigger.
Chemicals and Cleaning Solvents
Applying chemicals or cleaning solvents is a low-pressure operation.
NOTE: Use only soaps and chemicals designed for pressure washer
use. Do not use bleach.
TO APPLY CHEMICALS AND SOLVENTS
1. Press chemical hose (S) onto barbed fitting
S
located near high-pressure hose connection
of pump as shown.
2. Place the other end of chemical hose with
filter on it into the container holding chemi-
cal/cleaning solution.
NOTE: For every 10 gallons (38 liters) of
water pumped 1 gallon (3.8 liters) of chemi-
cal/cleaning solution will be used.
3.Installlow-pressure(black)nozzleintoquick-connectfittingofspray
wand, refer to Spray Wand Nozzles.
NOTE: Chemicals and soaps
will not siphon if the black soap nozzle is not installed on the
spray wand.
4. After use of chemicals, place chemical hose into container of clean
water and draw clean water through chemical injection system
to rinse system thoroughly. If chemicals remain in the pump it
could be damaged. Pumps damaged due to chemicals will not be
covered under warranty.
Starting
WARNING: To reduce the risk of injury, read the pressure washer
instruction manual and the engine instruction manual before starting
pressure washer.
DANGER: Risk of fluid injection and laceration. When using the
high-pressure setting,   allow the high-pressure spray to
come in contact with unprotected skin, eyes, or with any pets or
animals. Serious injury will occur.
13
English
• Your washer operates at fluid pressures and velocities high
enough to penetrate human and animal flesh, which could result
in amputation or other serious injury. Leaks caused by loose fit-
tings or worn or damaged hoses can result in injection injuries.
DO NOT TREAT FLUID INJECTION AS A SIMPLE CUT! See a
physician immediately!
WARNING: Risk of fire, asphyxiation and burning. NEVER fill fuel
tank when engine is running or hot. Do not smoke when filling fuel
tank.
  fill fuel tank completely. Fill tank to 1/2" (12.7 mm) below
bottom of filler neck to provide space for fuel expansion. Wipe any
fuel spillage from engine and equipment before starting engine.
  run engine in doors or in en closed, poorly ven ti lat ed
      
and deadly gas.
           
muffler during or immediately after use of your pressure
washer. Damage to hoses from contact with hot engine

NOTICE: 
This could damage hose and/or pump inlet.
 
  turn water supply off while pressure washer engine is
running or damage to pump will result.
 
T
two minutes at a time. Pump operates in
bypass mode when spray gun trigger is not
pressed. When the temperature inside the
pump rises too high the thermal relief valve (T)
will open and release a gush of water in an
effort to lower the temperature inside the pump. The thermal
relief valve will then close. If pump is left in bypass mode for
more than two minutes internal components of the pump can
be damaged.
START-UP PROCEDURE
1.Inawell-ventilatedoutdoorarea,addfresh,high-quality,unleaded
gasoline with a pump octane rating of 86 or higher. Do not overfill.
Wipe up spilled fuel before starting the engine. Refer to engine
instruction manual for correct procedure.
2. Check engine oil level. Refer to the engine instruction manual for
correct procedure.
3. Connect the water hose to the water source. Turn the water source
on to remove all air from the hose. When a steady stream of water
is present, turn the water source off.
4. Verify the filter screen (U) is in water inlet of pump.
U
The cone side faces out.
5. Connect the cold water source (V) to pump inlet.
NOTE: Water source must provide a minimum of
5 gallons per minute at 20 psi (138 kPa).
WARNING: To reduce the possibility of contami-
nation always protect against backflow when con-
nected to a potable water system.
6. Connect high-pressure hose (P) to pump
V
P
outlet.
7. If applying a chemical or cleaning solution,
refer to Chemicals and Cleaning Solvents.
8. Turn the water source on.
14
English
NOTICE: Risk of property damage. Failure to do so could cause
damage to the pump.
9. Remove all air from the pump and high-pressure hose by depress-
ing trigger until a steady stream of water is present.
10. Turn the engine ON/OFF switch (H) to the ON position.
11. Place the fuel valve lever (M) in the ON postion.
12.
If the engine is cold, move the choke (K) to the CLOSED position
as shown.
M
H
K
13. WARNING: Risk of unsafe operation. Pull starter grip slowly
until resistance is felt. Then pull starter grip (I, Fig. 1) rapidly to
avoid kickback and prevent hand or arm injury.
NOTE: Do not allow the starter grip to snap back. Return it gently
by hand.
WARNING: Risk of unsafe operation. If engine does not start
after two pulls, squeeze trigger of gun to relieve pump pressure. Pull
starter cord slowly until resistance is felt. Then pull cord rapidly to
avoid kickback and prevent hand or arm injury.
NOTE: If the oil level in the engine is low, the engine will not start.
If the engine does not start, check the oil level and add oil as
needed.
14. As the engine warms up, move the choke to
the OPEN position.
15. Depress trigger on gun to start water flow.
WARNING: Risk of unsafe operation. Stand
on a stable surface and grip gun/wand firmly with
       
triggered.
16. Release trigger to stop water flow.
DANGER:
X
trigger lock (X) when gun is not in use to prevent
accidental spraying.
17. Adjust spray for the task being performed
by changing quick connect nozzle. Refer to
Spray Wand Nozzles.
Shutting Down
1. If chemicals were applied, place the chemical hose into a
container of clean water and draw clean water through chemical
injection system to rinse system thoroughly.
NOTICE: Risk of property damage. Failure to do so could cause
damage to the pump.
2. Place the engine ON/OFF switch (H) to the OFF position.
3. Place the fuel valve lever (M) in the OFF
postion.
NOTICE: Risk of property damage.  turn
water supply off while pressure washer engine is
running or damage to pump will result.
4. Turn water source off.
5. Pull trigger on spray gun to relieve any water
pressure in hose or spray gun.
6. Refer to Storage for proper storage procedures.
15
English
Maintenance
WARNING: Risk of burning. When performing maintenance, you
may be exposed to hot surfaces, water pressure or moving parts that
can cause serious injury or death.
WARNING: Risk of fire. Always disconnect, spark plug wire, let
the engine cool and release all water pressure before performing
any maintenance or repair. The engine contains flammable fuel. Do
not smoke or work near open flames while performing maintenance.
To ensure efficient operation and longer life of your pressure washer,
a routine maintenance schedule should be prepared and followed.
If the pressure washer is used in unusual conditions, such as high
temperatures or dusty conditions, more frequent maintenance
checkswillberequired.
Engine
Consult the engine instruction manual for the man u fac tur er's recom-
mendations for any and all maintenance.
NOTE:Thepressurewasherframeisequippedwithanoildrain
hole to help make changing the engine oil easier.
Pump
NOTE: The pump was filled with oil at the factory. Change pump oil
after the first 50 hours of operation and every 300 hours thereafter,
or every 3 months. If using a 30W non-detergent oil, change oil every
150 hours thereafter.
TO CHECK OIL
The oil level should come to the dot in the middle
BB
CC
AA
of the sight glass (AA).
HOW TO CHANGE PUMP OIL
1. Loosen pump oil fill plug (BB).
2. Place a container under the oil drain plug
(CC).
3. Remove pump oil drain plug.
4. After oil is drained, replace oil drain plug.
Tighten securely.
5. Remove pump oil plug and fill with pump oil. An oil designed spe-
cifically for pressure washers is recommended as these contain a
rust inhibitor and an anit-foaming agent. If this oil is not available,
an SAE 30W non-detergent oil may be used.
6. Replace pump oil plug and tighten securely.
Nozzle Cleaning
If the nozzle becomes clogged with foreign materials, such as dirt,
excessive pressure may develop. If the nozzle becomes partially
clogged or restricted, the pump pressure will pulsate. Clean the
nozzle immediately using the nozzle kit supplied and the following
instructions:
1. Shut off the pressure washer and turn off the water supply.
2. Pull trigger on gun handle to relieve any water pressure.
3. Disconnect the spray wand from the gun.
4. Remove the high-pressure nozzle from the
Y
spray wand. Remove any obstructions
with the nozzle cleaning tool (Y) provided
and back flush with clean water.
16
English
5. Direct water supply into spray wand to
back flush loosened particles for 30
seconds.
6. Reassemble the nozzle to the wand.
7. Reconnect spray wand to gun then turn on water supply.
8. Start pressure washer and place spray wand into high-pressure
setting to test.
To Clean the Water Inlet Filter
This filter screen (U) should be checked periodically and cleaned if
necessary.
1. Remove the filter screen (U) by grasping the
U
end and removing it from water inlet of
pump.
2. Clean filter by flushing it with water on both
sides.
3. Reinsert filter into water inlet of pump. Cone
side faces out.
NOTE: Do not operate pressure washer without
filter properly installed.
To Remove Tires
1. Using a 1/8" hex head wrench loosen set
screw in hub collar.
2. Slide hub collar from axle and remove the
tire.
StoraGe
Engine
Consult the engine instruction manual for the man u fac tur er's
recommendations for storage.
Pump
The manufacturer recommends using a pump protector/winter-
izer, such as D
eWALT winterizer (DP80) when storing the unit
for more than 30 days and/or when freezing temperatures are
expected. D
eWALT winterizer (DP80) is availabe at the store
where the pressure washer was purchased. If a pump protector/
winterizer is not available, RV antifreeze can be used as outlined in
the following steps.
NOTE: Using a pump protector/ winterizer or RV antifreeze helps to
provide proper lubrication to the internal seals of the pump regard-
less of temperature or environment.
1. Obtain a funnel, 6 oz. (170 mL)
of RV antifreeze and 16–36"
(40–91cm) of garden hose with a
male hose connector attached to
one end.
NOTICE: Risk of property damage.
     
an ti freeze is corrosive and can dam-
age pump.
2. Disconnect spark plug wire.
3. Connect length of garden
hose to water inlet of pump.
4. Add RV antifreeze to hose as shown.
5. Pull engine starter rope slowly several times until an ti freeze
comes out of high-pressure hose con nec tion of pump.
6. Remove garden hose from water inlet of pump.
7. Reconnect spark plug wire.
17
English
Pressure Washer
1. Drain all water from high-
pressure hose, coil it and store it
in cradle of the pressure washer
handle.
2. With nozzle pointed down and
the spray gun and wand in a
vertical position, squeeze trigger
to drain all water from spray gun
and wand. Store in gun holder.
3. Store chemical hose so it is protected from dam age.
4. If space is needed, handles may be removed and attached as
shown.
CAUTION: Risk of personal injury. Avoid placing hands between
handle and frame when assembling to prevent pinching.
NOTICE: Risk of property damage. Always store and transport unit
in an upright position.
acceSSorieS
Recommended accessories for use with your tool are available for
purchase from your local dealer or authorized service center. If you
need assistance in locating any accessory for your tool, please con-
tact the FNA Group at www.dewaltpw.com, 1825 Greenleaf Avenue,
Elk Grove Village, Il 60007, or call (877) FNA-GAS1.
DANGER: Risk of fluid injection. When using replacement lances
or guns with this pressure washer,   use a lance and/or
lance/gun combination that is shorter in length than what was pro-
vided with this pressure washer as measured from the nozzle end
of the lance to the gun trigger.
WARNING: The use of any other accessory not recommended for
use with this tool could be hazardous. Use only accessories rated
equal to or higher than the rating of the pressure washer.
Service inForMation
Please have the following information available for all service calls:
Model Number ____________ Serial Number ___________
Date and Place of Purchase ____________________________
Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance
and adjustment should be performed by a FNA factory service
center,aFNA authorizedservicecenteror otherqualified service
personnel. Always use identical replacement parts.
Limited Warranty
This pressure washer is warranted for three years from date of pur-
chase. We will repair, without charge, any defects due to faulty mate-
rials or workmanship. This warranty does not cover parts that are
damaged through misuse or abuse, or parts which must be replaced
from time to time due to normal pressure washer operation. Normal
wear parts include, but are not limited to, the engine air filter, spark
plug, pump valve seals and O rings. This warranty does not apply to
accessories or damage caused where repairs have been made or
attempted by a repair center not authorized by FNA. This warranty
gives you specific legal rights and you may have other rights which
vary in certain states or provinces. For further details of warranty
coverage and warranty repair information, visit www.dewaltpw.com
and click on Service and Support or call 1-877-FNA-GAS1 (1-877-
362-4271).
18
English
LATIN AMERICA: This warranty does not apply to products sold in
Latin America. For products sold in Latin America, see country spe-
cific warranty information contained either in the packaging, call the
local company or see website for warranty information.
FREE WARNING LABEL REPLACEMENT: If your warning labels
become illegible or are missing, call 1-877-FNA-GAS1 (1-877-362-
4271) for a free replacement.
Glossary
Bypass mode: Allows water to re-circulate within pump when the
gun trigger is not pulled.
Chemical hose: Feeds cleaning agents into the pump to mix with
the water. Refer to Chemicals and Cleaning Solvents.
Chemical injection system: Mixes cleaners or cleaning solvents
with water to improve cleaning effectiveness.
Choke control: Opens and closes carburetor choke valve.
CU: Cleaning Units. GPM multiplied by psi. (GPM x PSI = CU)
Fuel valve lever: Opens/closes connection between fuel tank and
carburetor.
GPM: Gallons Per Minute. The unit of measure for the flow rate of
water.
PSI:PoundsperSquareInch.Theunitofmeasureforwaterpres-
sure. Also used for air pressure, hydraulic pressure, etc.
kPa (kilopascal): Metricpressuremeasurement.1kilopascalequal
1000 pascals.
Quick-connect spray wand: Allowstheusertoquicklychangeout
high-pressure nozzles. Refer to Spray Wand Nozzles.
Thermal relief valve: When the temperature inside the pump rises
too high the valve will open and release a gush of water in an effort
to lower the temperature inside the pump. The valve will then close.
Water supply: All pressure washers must have a source of water.
Theminimumrequirementsforawatersupplyare20psi(138kPa)
and 5 gallons per minute.
19
English
Troubleshooting Guide
This section provides a list of the more frequently encountered malfunctions, their causes and corrective actions. The
operatorormaintenancepersonnelcanperformsomecorrectiveactions,andothersmayrequiretheassistanceofaqualifiedFNAtechni-
cian or your dealer.
Problem Code
Engine will not start ......................................................................................................1, 2, 3, 4, 5, 6, 7, 8, 36
(refer to the engine's instruction manual for further engine troubleshooting)
No or low pressure (initial use) ......................................................................................9, 10, 11, 12, 13, 14, 15, 16
Will not draw chemicals .................................................................................................16, 17, 18, 19, 20, 21
No or low pressure (after period of normal use) ...........................................................22, 23, 24
Water leaking at gun/spray wand connection ................................................................25, 26
Water leaking at pump ...................................................................................................25, 26, 27, 28
Oil leaking at pump ........................................................................................................29, 30, 31, 32, 33, 34, 35
Pump pulsates ...............................................................................................................12
Troubleshooting Codes
CODE POSSIBLE CAUSE POSSIBLE SOLUTION
1 No fuel. Add fuel.
2 Low oil. Addrequiredamountofoil.
3 Pressure builds up after two pulls on the recoil starter or after initial
use.
Squeezeguntriggertorelievepressure.
4 Choke lever in the NO CHOKE position. Move choke to the CHOKE po si tion.
5 Spark plug wire not attached. Attach spark plug wire.
6 Engine ON/OFF switch in OFF po si tion. Place engine ON/OFF switch in ON position.
7 Choke lever in the CHOKE position on a hot engine or an engine
that has been exposed to thermal heat for a long period of time.
Move choke to the NO CHOKE po si tion.
8 Fuel valve closed. Move the fuel valve lever to the OPEN position.
20
English
(Troubleshooting Codes cont.)
CODE POSSIBLE CAUSE POSSIBLE SOLUTION
9 Spray wand not in high pressure. See Spray Wand Nozzles under .
10 Low water supply. Water supply must be at least 5 GPM @
20 psi (138 kPa)
.
11 Leak at high-pressure hose fitting. Repair leak. Apply sealant tape if necessary.
12 Nozzle obstructed. See Nozzle Cleaning under Maintenance.
13 Water filter screen clogged. Remove and clean filter.
14 Air in hose. Turn off the engine, then the water source. Disconnect the
water source from the pump inlet and turn the water source
on to remove all air from the hose. When there is a steady
stream of water present, turn water source off. Recon nect
watersourcetopumpinletandturnonwatersource.Squeeze
trigger to re move re main ing air.
15 Choke lever in the CHOKE position. Move choke to the NO CHOKE po si tion.
16 High-pressure hose is too long. Use high-pressure hose under 100 feet (30.48 m). Lengthen water
supply hose instead of high-pressure hose.
17 Spray wand not in low pressure. See Spray Wand Nozzles under .
18 Chemical filter clogged. Clean filter.
19 Chemical screen not in cleaning solution. Make sure end of chemical hose is fully submerged into cleaning
solution.
20 Chemical too thick. Dilute chemical. Chemical should be the same consistency as water.
21 Worn seal or packing. Have parts cleaned or replaced by authorized service center.
22 Chemical build up in chemical injector. Have replaced by an authorized service center.
23 Worn or obstructed valves. Have replaced by authorized service center.
24 Worn unloader piston. Have replaced by authorized service center.
25 Worn or broken O-ring. Check and replace.
26 Loose hose connection. Tighten.
27 Piston packings worn. Have replaced by authorized service center.
28 Pump head or tubes damaged from freezing. Have replaced by authorized service center.
29 Oil seals worn. Have replaced by authorized service center
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

DeWalt 7103629 Manuel utilisateur

Catégorie
Nettoyeurs haute pression
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues