Regency Classic S2400 Le manuel du propriétaire

Marque: Regency

Modèle: Classic S2400

Catégorie: Cheminées

Taper: Le manuel du propriétaire

Ce manuel convient également à

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4

919-542c

MODELS: F2400M S2400M

Classic™ F2400M / S2400M

Freestanding Woodstove

04.03.19

Installer: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner: Please keep these instructions for future reference.

Owners &

Installation Manual

Tested by:

F2400 Video

www.regency-re.com

French Manual: http://ow.ly/ZvmDk

Manuel en Français: http://ow.ly/ZvmDk

2 | Regency 2400 Freestanding Woodstove

Thank-you for purchasing a REGENCY FIREPLACE PRODUCT.

The pride of workmanship that goes into each of our products will give you years of trouble-free enjoyment. Should you have any questions about your product

that are not covered in this manual, please contact the REGENCY DEALER in your area. Keep those REGENCY FIRES burning.

“This wood heater has a manufacturer set minimum low burn rate that must not be altered. It is against federal regulations to alter this setting or otherwise

operate this wood heater in a manner inconsistent with operating instructions in this manual." Failure to follow the manual details can lead to smoke and CO

emissions spilling into the home. It is recommended to have monitors in areas that are expected to generate CO such as heater fuelling areas.

“U.S. ENVIRONMENTAL PROTECTION AGENCY Certiﬁed to comply with 2015 particulate emission standards using crib wood". Not approved for sale after

May 15, 2020.”

Model Regency F2400 and S2400 – 3.4 g /hr.

SAFETY NOTE: If this woodstove is not properly installed, a house ﬁre may result. For your safety, follow the installation instructions, contact local building,

ﬁre ofﬁcials, or authority having jurisdiction about restrictions and installation inspection requirements in your area.

The following statements are required by the Environmental Protection Agency:

“This manual describes the installation and operation of the Regency F2400 and S2400 wood heater. This heater meets the 2015 U.S. Environmental Pro-

tection Agency’s crib wood emission limits for wood heaters. Under speciﬁc test conditions this heater has been shown to deliver heat at rates ranging from

12,000 BTU/hr. to 36,800 BTU/hr.” This unit has been tested using 5G series and generates the best efﬁciency when operated using well-seasoned wood and

installed in the main living areas where the majority of the chimney is within the building envelope and fully lined.”

"It is against federal regulation to operate this wood heater in a manner inconsistent with operating instructions in this manual, or if any parts are removed. “

It is against federal regulation to operate this wood heater in a manner inconsistent with operating instructions in this manual.

CAUTION: BURN UNTREATED WOOD ONLY. OTHER MATERIALS SUCH AS WOOD PRESERVATIVES, METAL FOILS, COAL,

PLASTIC, GARBAGE, SULPHUR OR OIL MAY DAMAGE THE HEATER

"This heater is designed to burn natural wood only. Higher efﬁciencies and lower emissions generally result when burning air dried seasoned hardwoods, as

compared to softwoods or to green or freshly cut hardwoods."

DO NOT BURN:

• Treated wood • Lawn clippings or yard waste • Manure or animal remains

• Coal • Materials containing rubber including tires • Saltwater driftwood or other previously salt water

saturated materials

• Garbage • Materials containing plastic • Unseasoned wood

• Cardboard • Waste petroleum products , paints or paint thinners or asphalt products • Paper products, cardboard, plywood or particle

board. The prohibition against burning these

materials does not prohibit the use of ﬁre starters

made from paper, cardboard, saw dust, wax and

similar substances for the purpose of starting a

ﬁre in a wood heater

• Solvents • Materials containing asbestos

• Colored Paper • Construction or demolition debris

• Trash • Railroad ties

Burning these materials may result in release of toxic fumes or render the heater ineffective and cause smoke.

The authority having jurisdiction (such as Municipal Building Department, Fire Department, Fire Prevention Bureau, etc.) should be consulted before instal-

lation to determine the need to obtain a permit.

This unit must be connected to either a listed factory built chimney suitable for use with solid fuels and conforming to ULC629 in Canada or UL-103HT in the

United States of America or code approved masonry chimney with ﬂue liner.

F2400 and S2400 are tested and certiﬁed to ULC-S627-00 and UL1482-2011.

SAVE THESE INSTRUCTIONS

Regency 2400 Freestanding Woodstove | 3

Modular Parts

F2400 Video

ALL PICTURES / DIAGRAMS SHOWN THROUGHOUT THIS MANUAL ARE FOR ILLUSTRATION PURPOSES ONLY.

ACTUAL PRODUCT MAY VARY DUE TO PRODUCT ENHANCEMENTS.

4 | Regency 2400 Freestanding Woodstove

table of contents

Safety Label for F2400m ...............................................5

Safety Label for S2400M ...............................................6

F2400M Unit Dimensions ..............................................7

S2400M Unit Dimensions ..............................................8

Wood Stove Outside Air Dimensions .............................9

Residential Installation.................................................10

Modular Installation Options ........................................10

Room Air ..................................................................... 11

Important ..................................................................... 11

Minimum Clearance To Combustible Materials ........... 11

Stove Assembly Prior To Installation ...........................13

Step-by-step Chimney And Connector Installation ......14

Masonry Chimney........................................................15

Masonry Fireplace .......................................................15

Factory Built Chimney .................................................15

Combustible Wall Chimney

Connector Pass-throughs ............................................ 16

Recommended Heights For Woodstove Flue ..............17

Mobile Home Installation .............................................18

Listed Components For Mobile Home

Installation ...................................................................19

Flue Bae & Secondary Air Tube Installation .............19

Stainless steel smoke deector

adjustment / replacement ............................................20

Brick Installation ..........................................................21

Classic Door Handle .................................................... 21

Contemporary Door Handle.........................................21

Glass Installation .........................................................21

Step-by-step Optional Accessories Installation ...........21

Screen Door ................................................................22

Seasoned wood ........................................................... 23

Operating Instructions .................................................24

Draft Control ................................................................24

First Fire ......................................................................24

Fan Operation..............................................................25

Ash Disposal................................................................25

Safety Guidelines and Warnings .................................25

Maintenance ................................................................26

Creosote ......................................................................26

Maintenance Of Nickel-plated Doors ........................... 26

Latch Adjustment .........................................................26

Door Gasket ................................................................26

Glass Maintenance ...................................................... 26

Wood Storage ..............................................................26

F2400m Stove Main Assembly w/classic door ............27

F2400m Stove Main Assembly w/contemporary door .28

S2400m Step Stove Main Assembly w/classic door ....29

S2400m Step Stove Main Assembly

w/contemporary door ................................................... 30

Pedestal, Bottom Shield & Leg Options ......................31

Firebrick ....................................................................... 32

Warranty ......................................................................34

Regency 2400 Freestanding Woodstove | 5

safety decal

This is a copy of the label that accompanies each

Regency Freestanding Woodstove (F2400M).

We have printed a copy of the contents here

for your review.

NOTE: Regency units are constantly being

improved. Check the label on the unit and if

there is a difference, the label on the unit is the

correct one.

SAFETY LABEL FOR F2400M

Part #: 918-172f

Size: 6.53" H x 11.53" W (File at 100%)

Color: Everything printed black on grey except what is indicated is printed red on grey.

June 19/07: updated OMNI logo and standard as per SCC requirement.

Mar 1/10: Updated Omni Logo

Jan. 21/13: Updated yrs. of manufacture.

Feb. 17/14: Added French as per OMNI

May 06/15: Rev. E - Updated yrs. of manufacture/removed 1990 EPA info

Apr. 28/16: Rev. F - updated yrs of manufacture 2017-2021

MODEL: REGENCY MEDIUM FREESTANDING STOVE - F2400M

TESTED TO: UL-1482-2011 / ULC-S627-00 / UL-737-2011 REPORT NO:219-S-02-2

THE F2400M MEETS UL737 STANDARD FOR FIREPLACE STOVES WHEN A FIRESCREEN IS PROVIDED.

MINIMUM ALCOVE CEILING HEIGHT: 2.15 M / 7 FT MAXIMUM ALCOVE DEPTH 915 MM / 36 IN.

MINIMUM CLEARANCES FOR HORIZONTAL CONNECTOR TO CEILING: 455 MM / 18"

THE SPACE BENEATH THE HEATER MUST NOT BE OBSTRUCTED. OPERATE ONLY WITH FIREBRICKS IN PLACE.

F2400M WITHOUT

AIRMATE SHIELD

F2400M WITH

AIRMATE SHIELD

K 405 mm / 16 in

L 150 mm / 6 in

M 150 mm / 6 in

FOR USE WITH SOLID WOOD FUEL ONLY. USE OF OTHER FUELS MAY DAMAGE HEATER AND CREATE A HAZARDOUS CONDITION. DO NOT OBSTRUCT COMBUSTION

AIR OPENINGS. OPERATE ONLY WITH FIREBRICKS IN PLACE. RISK OF SMOKE AND FLAME SPILLAGE, OPERATE ONLY WITH DOORS FULLY OPEN OR FULLY CLOSED.

IF INSTALLED IN A MOBILE HOME OPERATE ONLY WITH DOORS FULLY CLOSED - OPEN FEED DOOR TO FEED FIRE ONLY. WHEN OPERATED WITH DOORS OPEN THE

MANUFACTURER SUPPLIED SCREEN MUST BE USED. DO NOT USE GRATE OR ELEVATE FIRE. BUILD WOOD FIRE DIRECTLY ON HEARTH. DO NOT OVERFIRE - IF HEATER

OR CHIMNEY CONNECTOR GLOWS YOU ARE OVERFIRING. INSPECT AND CLEAN CHIMNEY AND CONNECTOR FREQUENTLY. UNDER CERTAIN CONDITIONS OF USE

CREOSOTE BUILDUP MAY OCCUR RAPIDLY. KEEP FURNISHINGS AND OTHER COMBUSTIBLE MATERIAL AWAY FROM HEATER. REPLACE GLASS ONLY WITH NEOCERAM

GLASS. COMBUSTIBLE FLOOR MUST BE PROTECTED BY NON-COMBUSTIBLE MATERIAL EXTENDING BENEATH THE HEATER AND TO THE FRONT AND SIDES AS INDICATED

OR TO THE NEAREST PERMITTED COMBUSTIBLE MATERIAL.

OPTIONAL COMPONENT: FAN (846-515), ELECTRICAL RATING: VOLTS 115, 60 HZ, 2 AMPS, SCREEN DOOR (846-101)

DANGER: RISK OF ELECTRIC SHOCK. DISCONNECT POWER BEFORE SERVICING UNIT. DO NOT ROUTE POWER CORD UNDER OR IN FRONT OF APPLIANCE.

COMPONENTS REQUIRED FOR MOBILE HOME INSTALLATION: OUTSIDE AIR KIT AND ONE OF THE FOLLOWING DOUBLE WALL CONNECTOR

IN CANADA: LISTED SECURITY MODEL DP, OR OLIVER MACLEOD PRO-VENT PV DOUBLE WALLED CONNECTOR WITH LISTED CHIMNEY SYSTEM: SECURITY MODEL

S2100, ICC EXCEL 2100, SELKIRK SENTINAL CF.

IN USA: LISTED DOUBLE WALL CONNECTORS SECURITY MODEL DP, SELKIRK MODEL DS, OLIVER MACLEOD PRO VENT PV, SIMPSON DURA

VENT MODEL DVL, GSW SUPER PIPE 6, METAL-FAB DOUBLE WALL. CONNECTED TO ONE OF THE FOLLOWING COMPATIBLE CHIMNEY SYSTEMS

SECURITY MODEL S2100 OR MODEL ASHT, SELKIRK MODEL SSII, OLIVER MACLEOD PRO JET 3103, SIMPSON DURA PLUS, GSW MODEL SC OR

METAL-FAB TEMP/GUARD, AMERI-TEC HS, ICC EXCEL 2100 . USE CHIMNEY COMPONENTS AS SPECIFIED IN INSTALLATION INSTRUCTIONS.

AUTEUR MINIMALE DU PLAFOND DE L’ALCÔVE : 2.15 M / 7 PL PROFONDEUR MAXIMALE DE L’ALCÔVE : 915 MM / 36 PO

DÉGAGEMENT MINIMAL DU PLAFOND POUR UN CONNECTEUR HORIZONTAL : 455 MM / 18 PO.

L’ESPACE AU-DESSOUS DU POÊLE NE DOIT PAS ÊTRE OBSTRUÉ. UTILISER SEULEMENT AVEC LES BRIQUES RÉFRACTAIRES EN PLACE.

POUR UTILISATION AVEC BOIS SOLIDE SEULEMENT. L’UTILISATION D’AUTRES COMBUSTIBLES PEUT ENDOMMAGER LE POÊLE ET CRÉER UNE CONDITION DANGEREUSE.

NE PAS OBSTRUER LES OUVERTURES D’AIR DE COMBUSTION. UTILISER SEULEMENT AVEC LA PORTE FERMÉE – OUVRIR LA PORTE DE CHARGEMENT POUR ALIMENTER

LE FEU SEULEMENT. NE PAS UTILISER DE GRILLE À BÛCHES NI SURÉLEVER LE FEU. MONTER LE FEU DE BOIS DIRECTEMENT SUR L’ÂTRE. NE PAS SURCHAUFFER – SI

LE POÊLE OU LE CONNECTEUR DE CHEMINÉE SE MET À ROUGIR, VOUS SURCHAUFFEZ. INSPECTEZ ET NETTOYEZ FRÉQUEMMENT LA CHEMINÉE ET LE CONNECTEUREN

CERTAINES CONDITIONS D’UTILISATION, UN DÉPÔT DE CRÉOSOTE PEUT SE FORMER RAPIDEMENT. GARDEZ LES MEUBLES ET AUTRES MATÉRIAUX COMBUSTIBLES

ÉLOIGNÉS DU POÊLE. REMPLACEZ LA VITRE SEULEMENT PAR DU VERRE EN NEOCERAM. LE PLANCHER COMBUSTIBLE DOIT ÊTRE PROTÉGÉ PAR DES MATÉRIAUX NON

COMBUSTIBLES DÉPASSANT DU DESSOUS, DU DEVANT ET DES CÔTÉS DU POÊLE, TEL QU’INDIQUÉ, OU JUSQU’AU MATÉRIAU COMBUSTIBLE LE PLUS PRÈS PERMIS.

COMPOSANTS EN OPTION : VENTILATEUR (846-515), ALIMENTATION ÉLECTRIQUE : 115 VOLTS, 60 HZ, 2 AMP.

DANGER : RISQUE D’ÉLECTROCUTION. DÉCONNECTER L’ALIMENTATION ÉLECTRIQUE AVANT DE FAIRE L’ENTRETIEN DU POÊLE. NE PAS INSTALLER LE CORDON

ÉLECTRIQUE SOUS OU DEVANT L’APPAREIL.

COMPOSANTS EXIGÉS POUR INSTALLATION DANS UNE MAISON MOBILE : KIT DE PRISE D’AIR EXTÉRIEUR ET L’UN DES CONNECTEURS DE CHEMINÉE À DOUBLE PAROI

SUIVANTS :

AU CANADA : CONNECTEURS DE CHEMINÉE HOMOLOGUÉS À DOUBLE PAROI : SECURITY MODÈLE DP, OU OLIVER MACLEOD PRO-VENT PV, AVEC SYSTÈME DE CHEMINÉE

HOMOLOGUÉ : SECURITY MODÈLE S2100, ICC EXCEL 2100, SUPER VENT 2100, SUPERPRO 2100, CF SENTINAL.

AUX ÉTATS-UNIS : CONNECTEURS DE CHEMINÉE HOMOLOGUÉS À DOUBLE PAROI : SECURITY MODÈLE DP, SELKIRK MODEL DS, OLIVER MACLEOD PRO VENT PV,

SIMPSON DURA VENT MODÈLE DVL, GSW SUPER PIPE 6, METAL-FAB À DOUBLE PAROI. CONNECTÉ À L’UN DES SYSTÈMES DE CHEMINÉE COMPATIBLES SUIVANTS :

SECURITY MODÈLE S2100 OU MODÈLE ASHT, SELKIRK MODÈLE SSII, OLIVER MACLEOD PRO JET 3103, SIMPSON DURA PLUS, GSW MODÈLE SC OU METAL-FAB TEMP/

GUARD, AMERI-TECHS, ICC EXCEL 2100, SIMPSON DURA PLUS HTC. UTILISER LES COMPOSANTS DE CHEMINÉE SPÉCIFIÉS DANS LES INSTRUCTIONS D’INSTALLATION.

244

CAUTION

HOT WHILE IN OPERATION DO NOT TOUCH. KEEP CHILDREN,

CLOTHING AND FURNITURE AWAY. CONTACT MAY CAUSE

SKIN BURNS. READ NAMEPLATE AND INSTRUCTIONS.

ATTENTION

CHAUD DURANT LE FONCTIONNEMENT. NE TOUCHEZ PAS.

ÉLOIGNEZ LES ENFANTS, LES VÊTEMENTS ET LES MEUBLES.

LE CONTACT PEUT CAUSER DES BRÛLURES DE LA PEAU.

LISEZ LA PLAQUE SIGNALÉTIQUE ET LES INSTRUCTIONS

MADE IN CANADA / FAIT AU CANADA

MANUFACTURED BY/ FABRIQUÉ PAR:

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD.

6988 VENTURE ST.

DELTA, BC V4G 1H4

LISTED SPACE HEATER, SOLID FUEL TYPE, ALSO

SUITABLE FOR MOBILE HOME INSTALLATION /

APPAREIL DE CHAUFFAGE AMBIANT HOMOLOGUÉ

À COMBUSTIBLE SOLIDE, CONVENANT AUSSI

POUR INSTALLATION DANS UNE MAISON MOBILE

FLOOR PROTECTION*

PROTECTION DE PLANCHER*

* Au Canada, la protection de plancher doit dépasser de

18 po (457 mm) à l’avant et de 8 po (200 mm) de chaque

côté du poêle et derrière le

poêle.

* In Canada, ﬂoor protection must extend 18" (450mm)

to the front and 8" (200mm) to each side and back of

the stove.

DO NOT REMOVE THIS LABEL/

NE RETIREZ PAS CETTE ÉTIQUETTE

244

INSTALL AND USE ONLY IN ACCORDANCE WITH THE MANUFACTURER'S INSTALLATION AND OPERATING INSTRUCTIONS.

CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR AREA.

USE 150 MM (6 IN.) DIAMETER MINIMUM 24 MSG BLACK OR 26 MSG BLUED STEEL CONNECTOR WITH LISTED UL103 HT

FACTORY-BUILT CHIMNEY SUITABLE FOR USE WITH SOLID FUELS OR MASONRY CHIMNEY.

SEE LOCAL BUILDING CODE AND MANUFACTURER'S INSTRUCTIONS FOR PRECAUTIONS REQUIRED FOR PASSING A

CHIMNEY THROUGH A COMBUSTIBLE WALL OR CEILING. DO NOT PASS CHIMNEY CONNECTOR THROUGH COMBUSTIBLE

WALL OR CEILING. DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

INSTALLER ET UTILISER SEULEMENT SELON LES INSTRUCTIONS D’INSTALLATION ET D’UTILISATION DU FABRICANT.

CONTACTER LES RESPONSABLES DU BÂTIMENT OU DU SERVICE-INCENDIE DE VOTRE RÉGION POUR CONNAÎTRE

LES RESTRICTIONS ET EXIGENCES D’INSPECTION DANS VOTRE RÉGION. UTILISER UN CONNECTEUR D’UN DIAMÈTRE

MINIMAL DE 150 MM (6 PO) 24 MSG EN ACIER NOIR OU 26 MSG EN ACIER BRONZÉ AVEC CHEMINÉE PRÉFABRIQUÉE

HOMOLOGUÉE UL103 HT CONÇUE POUR UTILISATION AVEC COMBUSTIBLES SOLIDES OU UNE CHEMINÉE DE MAÇON-

NERIE.

VOIR LE CODE DU BÂTIMENT LOCAL ET LES INSTRUCTIONS DU FABRICANT CONCERNANT LES PRÉCAUTIONS

EXIGÉES POUR INSTALLER UNE CHEMINÉE TRAVERSANT UN MUR OU PLAFOND EN MATÉRIAUX COMBUSTIBLES.

NE FAITES PAS TRAVERSER LE CONNECTEUR DE CHEMINÉE DANS UN MUR OU PLAFOND EN MATÉRIAUX COMBUS-

TIBLES. NE RACCORDEZ PAS CE POÊLE À BOIS À UN CONDUIT DE CHEMINÉE DESSERVANT UN AUTRE APPAREIL.

MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS

DÉGAGEMENTS MINIMUMS AUX MATÉRIAUX COMBUSTIBLES

F2400M WITH AIRMATE SHIELD F2400M WITHOUT AIRMATE SHIELD

RESIDENTIAL INSTALLATION USING

SINGLE WALL CONNECTOR

MEASURE FLUE

FROM HEATER CENTER-LINE

RESIDENTIAL INSTALLATION USING

SINGLE WALL CONNECTOR

SIDEWALL A 457 mm / 18 in D 762 mm / 30 in

BACKWALL B 305 mm / 12 in E 470 mm / 18.5 in

CORNER C 165 mm / 6.5 in F 457 mm / 18 in

INSTALLATION USING LISTED DOUBLE WALL

CONNECTOR - MOBILE HOME

SIDEWALL A 380 mm / 15 in D 685 mm / 27 in

BACKWALL B 165 mm / 6.5 in E 330 mm / 13 in

CORNER C 152 mm / 6 in F 444 mm / 17.5in

INSTALLATION USING LISTED DOUBLE WALL

CONNECTOR - RESIDENTIAL CLOSE CLEARANCE

SIDEWALL A 380 mm / 15 in D 685 mm / 27 in

BACKWALL B 165 mm / 6.5in E 330 mm / 13 in

CORNER C 152 mm / 6 in F 444 mm / 17.5 in

INSTALLATION USING LISTED DOUBLE WALL

CONNECTOR - ALCOVE

SIDEWALL A 406 mm / 16 in D 711 mm / 28 in

BACKWALL B 280 mm / 11 in E 444 mm / 17.5 in

CORNER C 152 mm / 6 in F 444 mm / 17.5 in

INSTALLATION USING LISTED DOUBLE WALL

CONNECTOR - MOBILE HOME

SIDEWALL A 380 mm / 15 in D 685 mm / 27 in

BACKWALL B 140 mm / 5.5 in E 304 mm / 12 in

CORNER C 102 mm / 4 in F 393 mm / 15.5 in

SIDEWALL A 380 mm / 15 in D 685 mm / 27 in

BACKWALL B 140 mm / 5.5 in E 304 mm / 12 in

CORNER C 102 mm / 4 in F 393 mm / 15.5 in

INSTALLATION USING LISTED DOUBLE WALL

CONNECTOR - RESIDENTIAL CLOSE CLEARANCE

INSTALLATION USING LISTED DOUBLE WALL

CONNECTOR - ALCOVE

SIDEWALL G 380 mm / 15 in I 685 mm / 27 in

BACKWALL H 165 mm / 6.5 in J 330 mm / 13 in

MEASURE FLUE

FROM HEATER CENTER-LINE

SIDEWALL G 380 mm / 15 in I 685 mm / 27 in

BACKWALL H 140 mm / 5.5in J 304 mm / 12 in

918-172f

JAN FEB MAR APR MAY JUN JUL AUG SEPT OCT NOV DEC

DATE OF MANUFACTURE

2017 2019

2020

2021

2018

6 | Regency 2400 Freestanding Woodstove

safety decal

This is a copy of the label that accompanies

each Regency Medium Freestanding Step

Stove (S2400M). We have printed a copy of the

contents here for your review.

NOTE: Regency units are constantly being

improved. Check the label on the unit and if

there is a difference, the label on the unit is the

correct one.

SAFETY LABEL FOR S2400M

MODEL: REGENCY MEDIUM FREESTANDING STEP STOVE - S2400M

TESTED TO: UL-1482-2011 / ULC-S627-00 / UL-737-2011 REPORT NO:219-S-02-2

THE S2400M MEETS UL737 STANDARD FOR FIREPLACE STOVES WHEN A FIRESCREEN IS PROVIDED.

S2400M

K 405 mm / 16 in

L 150 mm / 6 in

M 150 mm / 6 in

MINIMUM ALCOVE CEILING HEIGHT: 2.15 M / 7 FT MAXIMUM ALCOVE DEPTH 915 MM / 36 IN.

MINIMUM CLEARANCES FOR HORIZONTAL CONNECTOR TO CEILING: 455 MM / 18"

THE SPACE BENEATH THE HEATER MUST NOT BE OBSTRUCTED. OPERATE ONLY WITH FIREBRICKS IN PLACE.

FOR USE WITH SOLID WOOD FUEL ONLY. USE OF OTHER FUELS MAY DAMAGE HEAT ER AND CREATE A HAZARDOUS CONDITION. DO NOT OBSTRUCT COMBUSTION

AIR OPENINGS. OPERATE ONLY WITH FIREBRICKS IN PLACE. RISK OF SMOKE AND FLAME SPILLAGE, OPERATE ONLY WITH DOORS FULLY OPEN OR FULLY CLOSED.

IF INSTALLED IN A MOBILE HOME OPERAT E ONLY WITH DOORS FULLY CLOSED - OPEN FEED DOOR TO FEED FIRE ONLY. WHEN OPERAT ED WITH DOORS OPEN THE

MANUFACTURER SUPPLIED SCREEN MUST BE USED. DO NOT USE GRATE OR ELEVATE FIRE. BUILD WOOD FIRE DIRECTLY ON HEARTH. DO NOT OVERFIRE - IF HEATER

OR CHIMNEY CONNECTOR GLOWS YOU ARE OVERFIRING. INSPECT AND CLEAN CHIMNEY AND CONNECTOR FREQUENTLY. UNDER CERTAIN CONDITIONS OF USE

CREOSOTE BUILDUP MAY OCCUR RAPIDLY. KEEP FURNISHINGS AND OTHER COMBUSTIBLE MATERIAL AWAY FROM HEATER. REPLACE GLASS ONLY WITH NEOCERAM

GLASS. COMBUSTIBLE FLOOR MUST BE PROTECTED BY NON-COMBUSTIBLE MATERIAL EXTENDING BENEATH THE HEATER AND TO THE FRONT AND SIDES AS INDICATED

OR TO THE NEAREST PERMITTED COMBUSTIBLE MATERIAL.

OPTIONAL COMPONENT: FAN (846-515), ELECTRICAL RATING: VOLTS 115, 60 HZ, 2 AMPS, SCREEN DOOR (846-101)

DANGER: RISK OF ELECTRIC SHOCK. DISCONNECT POWER BEFORE SERVICING UNIT. DO NOT ROUTE POWER CORD UNDER OR IN FRONT OF APPLIANCE.

COMPONENTS REQUIRED FOR MOBILE HOME INSTALLATION: OUTSIDE AIR KIT AND ONE OF THE FOLLOWING DOUBLE WALL CONNECTOR

IN CANADA: LISTED SECURITY MODEL DP, OR OLIVER MACLEOD PRO-VENT PV DOUBLE WALLED CONNECTOR WITH LISTED CHIMNEY SYSTEM: SECURITY MODEL

S2100, ICC EXCEL 2100, SELKIRK SENTINAL CF.

IN USA: LISTED DOUBLE WALL CONNECTORS SECURITY MODEL DP, SELKIRK MODEL DS, OLIVER MACLEOD PRO VENT PV, SIMPSON DURA

VENT MODEL DVL, GSW SUPER PIPE 6, METAL-FAB DOUBLE WALL. CONNECTED TO ONE OF THE FOLLOWING COMPATIBLE CHIMNEY SYSTEMS

SECURITY MODEL S 2100 OR MODEL ASHT, SELKIRK MODEL SSII, OLIVER MACLEOD PRO JET 3103, SIMPSON DURA PLUS, GSW MODEL SC OR

METAL-FAB T EMP/GUARD, AMERI-TEC HS, ICC EXCEL 2100 . U SE CHIMNEY COMPONENTS AS SPECIFIED IN INSTALLATION INSTRUCTIONS.

AUTEUR MINIMALE DU PLAFOND DE L’ALCÔVE : 2.15 M / 7 PL PROFONDEUR MAXIMALE DE L’ALCÔVE : 915 MM / 36 PO

DÉGAGEMENT MINIMAL DU PLAFOND POUR UN CONNECTEUR HORIZONTAL : 455 MM / 18 PO.

L’ESPACE AU-DESSOUS DU POÊLE NE DOIT

PAS ÊTRE OBSTRUÉ. UTILISER SEULEMENT AVEC LES BRIQUES RÉFRACTAIRES EN PLACE.

POUR UTILISATION AVEC BOIS SOLIDE SEULEMENT. L’UTILISATION D’AUTRES COMBUSTIBLES PEUT ENDOMMAGER LE POÊLE ET CRÉER UNE CONDITION DANGEREUSE.

NE PAS OBSTRUER LES OUVERTURES D’AIR DE COMBUSTION. UTILISER SEULEMENT AVEC LA PORTE FERMÉE – OUVRIR LA PORTE DE CHARGEMENT POUR ALIMENTER

LE FEU SEULEMENT. NE PAS UTILISER DE GRILLE À BÛCHES NI SURÉLEVER LE FEU. MONTER LE FEU DE BOIS DIRECTEMENT SUR L’ÂTRE. NE PAS SURCHAUFFER – SI

LE POÊLE OU LE CONNECTEUR DE CHEMINÉE SE MET À ROUGIR, VOUS SURCHAUFFEZ. INSPECTEZ ET NETTOYEZ FRÉQUEMMENT LA CHEMINÉE ET LE CONNECTEUREN

CERTAINES CONDITIONS D’UTILISATION, UN DÉPÔT DE CRÉOSOTE PEUT SE FORMER RAPIDEMENT. GARDEZ LES MEUBLES ET AUTRES MATÉRIAUX COMBUSTIBLES

ÉLOIGNÉS DU POÊLE. REMPLACEZ LA VITRE SEULEMENT PAR DU VERRE EN NEOCERAM. LE PLANCHER COMBUSTIBLE DOIT ÊTRE PROTÉGÉ PAR DES MATÉRIAUX NON

COMBUSTIBLES DÉPASSANT DU DESSOUS, DU DEVANT ET DES CÔTÉS DU POÊLE, TEL QU’INDIQUÉ, OU JUSQU’AU MATÉRIAU COMBUSTIBLE LE PLUS PRÈS PERMIS.

COMPOSANTS EN OPTION : VENTILATEUR (846-515), ALIMENTATION ÉLECTRIQUE : 115 VOLT S, 60 HZ, 2 AMP.

DANGER : RISQUE D’ÉLECTROCUTION. DÉCONNECTER L’ALIMENTATION ÉLECTRIQUE AVANT DE FAIRE L’ENTRETIEN DU POÊLE. NE PA S INSTALLER LE CORDON

ÉLECTRIQUE SOUS OU DEVANT L’APPAREIL.

COMPOSANTS EXIGÉS POUR INSTALLATION DANS UNE MAISON MOBILE : KIT DE PRISE D’AIR EXTÉRIEUR ET L’UN DES CONNECTEURS DE CHEMINÉE À DOUBLE PAROI

SUIVANTS :

AU CANADA : CONNECTEURS DE CHEMINÉE HOMOLOGUÉS À DOUBLE PAROI : SECURITY MODÈLE DP, OU OLIVER MACLEOD PRO-VENT PV, AVEC SYSTÈME DE CHEMINÉE

HOMOLOGUÉ : SECURITY MODÈLE S2100, ICC EXCEL 2100, SUPER VENT 2100, SUPERPRO 2100, CF SENTINAL.

AUX ÉTATS-UNIS : CONNECTEURS DE CHEMINÉE HOMOLOGUÉS À DOUBLE PAROI : SECURITY MODÈLE DP, SELKIRK MODEL DS, OLIVER MACLEOD PRO VENT PV,

SIMPSON DURA VENT MODÈLE DVL, GSW SUPER PIPE 6, METAL-FAB À DOUBLE PAROI. CONNECTÉ À L’UN DES SYSTÈMES DE CHEMINÉE COMPATIBLES SUIVANTS :

SECURITY MODÈLE S2100 OU MODÈLE ASHT, SELKIRK MODÈLE SSII, OLIVER MACLEOD PRO JET 3103, SIMPSON DURA PLUS, GSW MODÈLE SC OU METAL-FAB TEMP/

GUARD, AMERI-TECHS, ICC EXCEL 2100, SIMPSON DURA PLUS HTC. UTILISER LES COMPOSANTS DE CHEMINÉE SPÉCIFIÉS DANS LES INSTRUCTIONS D’INSTALLATION.

245

CAUTION

HOT WHILE IN OPERATION DO NOT TOUCH. KEEP CHILDREN,

CLOTHING AND FURNITURE AWAY. CONTACT MAY CAUSE

SKIN BURNS. READ NAMEPLATE AND INSTRUCTIONS.

ATTENTION

CHAUD DURANT LE FONCTIONNEMENT. NE TOUCHEZ PAS.

ÉLOIGNEZ LES ENFANTS, LES VÊTEMENTS ET LES MEUBLES.

LE CONTACT PEUT CAUSER DES BRÛLURES DE LA PEAU.

LISEZ LA PLAQUE SIGNALÉTIQUE ET LES INSTRUCTIONS

MADE IN CANADA / FAIT AU CANADA

MANUFACTURED BY/ FABRIQUÉ PAR:

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD.

6988 VENTURE ST.

DELTA, BC V4G 1H4

LISTED SPACE HEATER, SOLID FUEL TYPE, ALSO

SUITABLE FOR MOBILE HOME INSTALLATION /

APPAREIL DE CHAUFFAGE AMBIANT HOMOLOGUÉ

À COMBUSTIBLE SOLIDE, CONVENANT AUSSI

POUR INSTALLATION DANS UNE MAISON MOBILE

FLOOR PROTECTION*

PROTECTION DE PLANCHER*

* In Canada, ﬂ oor protection must extend 18" (450mm)

to the front and 8" (200mm) to each side and back of

the stove.

DO NOT REMOVE THIS LABEL/

NE RETIREZ PAS CETTE ÉTIQUETTE

245

INSTALL AND USE ONLY IN ACCORDANCE WITH THE MANUFACTURER'S INSTALLATION AND OPERATING INSTRUCTIONS.

CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR AREA.

USE 150 MM (6 IN.) DIAMETER MINIMUM 24 MSG BLACK OR 26 MSG BLUED STEEL CONNECTOR WITH LISTED UL103 HT

FACTORY-BUILT CHIMNEY SUITABLE FOR USE WITH SOLID FUELS OR MASONRY CHIMNEY.

SEE LOCAL BUILDING CODE AND MANUFACTURER'S INSTRUCTIONS FOR PRECAUTIONS REQUIRED FOR PA SSING A

CHIMNEY THROUGH A COMBUSTIBLE WALL OR CEILING. DO NOT PASS CHIMNEY CONNECTOR THROUGH COMBUSTIBLE

WALL OR CEILING. DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

INSTALLER ET UTILISER SEULEMENT SELON LES INSTRUCTIONS D’INSTALLATION ET D’UTILISATION DU FABRICANT.

CONTACTER LES RESPONSABLES DU BÂTIMENT OU DU SERVICE-INCENDIE DE VOTRE RÉGION POUR CONNAÎTRE

LES RESTRICTIONS ET EXIGENCES D’INSPECTION DANS VOTRE RÉGION. UTILISER UN CONNECTEUR D’UN DIAMÈTRE

MINIMAL DE 150 MM (6 PO) 24 MSG EN ACIER NOIR OU 26 MSG EN ACIER BRONZÉ AVEC CHEMINÉE PRÉFABRIQUÉE

HOMOLOGUÉE UL103 HT CONÇUE POUR UTILISATION AVEC COMBUSTIBLES SOLIDES OU UNE CHEMINÉE DE MAÇON-

NERIE.

VOIR LE CODE DU BÂTIMENT LOCAL ET LES INSTRUCTIONS DU FABRICANT CONCERNANT LES PRÉCAUTIONS

EXIGÉES POUR INSTALLER UNE CHEMINÉE TRAVERSANT UN MUR OU PLAFOND EN MATÉRIAUX COMBUSTIBLES.

NE FAITES PAS TRAVERSER LE CONNECTEUR DE CHEMINÉE DANS UN MUR OU PLAFOND EN MATÉRIAUX COMBUS-

TIBLES. NE RACCORDEZ PAS CE POÊLE À BOIS À UN CONDUIT DE CHEMINÉE DESSERVANT UN AUTRE APPAREIL.

918-203f

JAN FEB MAR APR MAY JUN JUL AUG SEPT OCT NOV DEC

DATE OF MANUFACTURE

2017 2019 2020 20212018

S2400M MINIMUM CLEARANCES

TO COMBUSTIBLE MATERIALS

RESIDENTIAL INSTALLATION USING

SINGLE WALL CONNECTOR

INSTALLATION USING LISTED DOUBLE WALL

CONNECTOR - ALCOVE

SIDEWALL A 406 mm / 16 in D 711 mm / 28 in

BACKWALL B 280 mm / 11 in E 444 mm / 17.5 in

CORNER C 152 mm / 6 in F 483 mm / 19 in

INSTALLATION USING LISTED DOUBLE WALL

CONNECTOR - MOBILE HOME

SIDEWALL A 380 mm / 15 in D 685 mm / 27 in

BACKWALL B 140 mm / 5.5 in E 304 mm / 12 in

CORNER C 102 mm / 4 in F 432 mm / 17 in

SIDEWALL A 380 mm / 15 in D 685 mm / 27 in

BACKWALL B 140 mm / 5.5 in E 304 mm / 12 in

CORNER C 102 mm / 4 in F 432 mm / 17 in

INSTALLATION USING LISTED DOUBLE WALL

CONNECTOR - RESIDENTIAL CLOSE CLEARANCE

MEASURE FLUE

FROM HEATER CENTER-LINE

SIDEWALL G 380 mm / 15 in I 685 mm / 27 in

BACKWALL H 140 mm / 5.5in J 304 mm / 12 in

DÉGAGEMENTS MINIMUMS AUX

MATÉRIAUX COMBUSTIBLES

INSTALLATION RÉSIDENTIELLE UTILISANT

UN CONNECTEUR À SIMPLE PAROI

MUR LATÉRAL

MUR ARRIÈRE

COIN

MUR LATÉRAL

MUR ARRIÈRE

COIN

MUR LATÉRAL

MUR ARRIÈRE

COIN

MUR LATÉRAL

MUR ARRIÈRE

A 406mm/16po

B 280mm/11po

152mm/6po

A 380mm/15po

B 140mm/5.5po

C 102mm/4po

A 380mm/15po

B 140mm/5.5po

C 102mm/4po

G 380mm/15po

H 140mm/5.5po

D 711mm/28po

E 444mm/17.5po

F 483mm/19po

D 685mm/27po

E 304mm/12po

F 432mm/17po

D 685mm/27po

E 304mm/12po

F 432mm/17po

I 685mm/27po

J 304mm/12po

INSTALLATION UTILISANT UN CONNECTEUR

HOMOLOGUÉ À DOUBLE PAROI - ALCÔVE

INSTALLATION UTILISANT UN CONNECTEUR

HOMOLOGUÉ À DOUBLE PAROI - MAISON MOBILE

INSTALLATION UTILISANT UN CONNECTEUR HOMOLOGUÉ

À DOUBLE PAROI - RÉSIDENTIELLE (DÉGAGEMENT

RÉDUIT

)

MESURER DU CENTRE DU

A PARTIR DU POÊLE CONDUIT DE FUMÉE

* Au Canada, la protection de plancher doit dépasser de

18 po (457 mm) à l’avant et de 8 po (200 mm) de chaque

côté du poêle et derrière le poêle.

Regency 2400 Freestanding Woodstove | 7

dimensions

F2400M UNIT DIMENSIONS

Classic DoorContemporary Door

33-7/16”

31-1/2”

7-3/4”

(197mm)

(799mm)

(848mm)

w/ Optional Legs

8 | Regency 2400 Freestanding Woodstove

dimensions

S2400M UNIT DIMENSIONS

Classic Door

Contemporary Door

7-3/4”

35-5/8”

33-5/8”

(197mm)

(905mm)

(854mm)

w/ Optional Legs

Regency 2400 Freestanding Woodstove | 9

dimensions

WOOD STOVE OUTSIDE AIR DIMENSIONS

With pedestal from base of unit to centerline

4-1/2" (114mm)

With bottom heat shield from rear heat shield to centerline

6-3/4"(171mm)

Rear

Front

Rear

10 | Regency 2400 Freestanding Woodstove

installation

RESIDENTIAL

INSTALLATION

1) Please read this entire manual before you install

and use your new woodstove. Failure to follow

instructions may result in property damage,

bodily injury or even death. Be aware that local

Codes and Regulations may override some

items in this manual. Check with your local

inspector.

2) Select a position for your Regency Stove.

Consult the minimum clearance chart for your

model and set the stove in place. For close

clearance installation use listed double wall

connector systems.

3) To insure vertical alignment, suspend a plumb

bob from the ceiling over the exact center of

your stove ﬂue and mark a spot on the ceiling

to indicate the center of the chimney.

4) Check that the area above the ceiling is clear

for cutting. Re-conﬁrm the clearance from the

stove to combustibles to insure that they are

within the prescribed limits.

5) This woodstove must be connected to a UL

103 HT (ULC S629) listed chimney or a code

approved masonry chimney with a ﬂue liner.

6) Install chimney according to chimney manu-

facturers instructions. The performance of your

woodstove is governed to a very large part by

the chimney system. Too short a chimney can

cause difﬁcult start-up, dirty glass, back smok-

ing when door is open, and even reduced heat

output.

Too tall a chimney may prompt excessive

draft which can result in very short burn

times and excessive heat output. The use

of an inexpensive ﬂue pipe damper may be

helpful in reducing excessive draft.

CAUTION: The chimney should be the same

size as the 6" ﬂue outlet on the stove. The

chimney must be listed as suitable for use

with solid fuels. For other types of chimneys

check with your local building code ofﬁcials.

Do not confuse a chimney with a type “B”

Venting System used for gas appliances

as suitable for a wood burning appliance.

For Mobile Home installations refer to that

section within this manual.

7) Mark the location of the pedestal base or

legs on the ﬂoor, then move the stove aside

and mark the position of the ﬂoor protector.

8) The ﬂoor protector must be of non-combus-

tible material and must extend 16" (406mm)

in front of the door opening and 6" (152mm)

to the sides and rear of the unit. Some areas

may require a larger size ﬂoor protector.

See your local inspector. For outside air

installation refer to Mobile Home installation

instructions within this manual.

9) When the ﬂoor protection is complete, posi-

tion the stove with the ﬂue collar centered

under the installed chimney.

10) In areas of seismic activity, Regency rec-

ommends that your unit is secured to the

ﬂoor by using the bolt down holes inside

the pedestal (the same ones used in Mobile

Home installations).

11) For residential installations using 6" "C"

Vent (single wall) the chimney connector

must be at least 24 gauge steel. Do not use

galvanized pipe. For Mobile Home installa-

tion refer to the Mobile Home installation

instructions within this manual.

12) Do not connect this unit to a chimney

serving another appliance.

13) A chimney connector cannot pass through

an attic or roof space, closet or similar

concealed space, or a ﬂoor, ceiling, wall

or partition of combustible construction.

In Canada, if passage through a wall, or

partition of combustible construction is

desired, the installation shall conform to

CAN/CSA-B365, Installation Code for Solid-

Fuel-Burning Appliances and Equipment.

14) Your Regency Woodstove is not to be con-

nected to any air distribution duct.

NOTE: In Canada, oor protection must

extend 18" (450mm) to the front

and 8" (200mm) to each side and

back of the stove.

MODULAR INSTALLATION OPTIONS

WARNING: ONLY USE SPECIFIED COMPONENTS.

The following items are required when assembling your Regency Stove. F2400 unit - the Rear Heat Deﬂector is supplied with the stove, but if you choose

not to use it you must use the Airmate instead.

Modular Part

Clearances are different. Generally you can get closer clearances with the airmate than with the rear heat deﬂector.

Airmate OR

Rear Heat Deﬂector

Convection heat with Airmate vs. Radiant Heat with Rear Heat Deﬂector. The Airmate pushes heat forward out into

the room, the Rear Heat Deﬂector deﬂects the heat upward. Refer to the Installation sections within this manual.

Pedestal or Legs

There are no performance differences with either the pedestal or legs. It is primarily a personal preference. Legs can

be either painted steel or painted cast.

Leg installation requires the bottom shield.

OPTIONS: These can be installed at time of installation or added later:

Blower/Fan

Adding the blower will increase the area heated by the stove, it can move warm air beyond the room where the stove

is located.

Ash Drawer Kit

Adding the Ash Drawer Kit makes cleaning ashes out of the stove easier and cleaner (refer to Bottom Shield Ash

Drawer Kit, Installation section).

Screen Door

A simple add-on option that will allow you to enjoy the sound, warmth and view of an open ﬁre.

Regency 2400 Freestanding Woodstove | 11

installation

ROOM AIR

IMPORTANT

For installation using room air for combustion,

remove knockout from the pedestal, and/or from

the bottom if using a heat shield.

Mobile home installations require the use of

outside air.

On pedestal units there are two locations where

MINIMUM CLEARANCE TO

COMBUSTIBLE MATERIALS

Please read the section below carefully as clearances depend on whether the airmate or the

rear heat deﬂector is installed on the stove.

Measurements "From Unit" are from the top plate of the stove to a side wall or to a corner,

and from the rear heat shield to a back wall.

Clearances may only be reduced by means approved by the regulatory authority.

outside air may be adapted to the unit. If using

the bottom of the pedestal, do not remove knock-

out from the rear of the pedestal. Only remove

rear knockout if outside air will be brought in

from the rear.

On leg units outside air can only be brought in

from the bottom of the heat shield.

Note: Once the knockout is removed there

are two tabs remaining. Bend both

tabs out for ease of installation when

attaching outside air.

NOTE: Be aware that local Codes and Regulations may override some clearances listed in this manual.

Check with your local inspector.

NOTE: This clearance is also required for air space between the apliance and wall/ceiling.

Residential Installation “C” Vent (Single Wall)

Unit From Unit From Corner From Flue Center-Line

A B C D E F

Medium F2400M with Airmate

16" (406 mm) 11" (280 mm) 6" (152 mm) 28" (710 mm) 17.5" (444 mm) 17.5" (444 mm)

with Rear Deector

18" (457 mm) 12" (304 mm) 6.5" (165 mm) 30" (762 mm) 18.5" (470 mm) 19.5" (495 mm)

Medium S2400M Step Stove

16" (406 mm) 11" (279 mm) 6" (152 mm) 28" (710 mm) 17.5" (432 mm) 19" (483 mm)

Residential Close Clearance (To be installed with required pipe components)

When the stove is installed as a close clearance residential unit, a listed double wall connector is required from the stove collar to the ceiling level.

Unit From Unit From Corner From Flue Center-Line

A B C D E F

Medium F2400M with Airmate

15" (381 mm) 5.5" (139 mm) 4" (101 mm) 27" (685 mm) 12" (304 mm) 15.5" (393 mm)

with Rear Deector

15" (381 mm) 6.5" (165 mm) 6" (152 mm) 27" (685 mm) 13" (330 mm) 17.5" (444 mm)

Medium S2400M Step Stove

15" (381 mm) 5.5" (139 mm) 4" (101 mm) 27" (685 mm) 12" (304 mm) 17" (432 mm)

Mobile Home Close Clearance (To be installed with required pipe components)

"C" Vent single wall pipe is not approved for Mobile Home installations. (Refer to Mobile Home Instructions.)

Unit From Unit From Corner From Flue Center-Line

A B C D E F

Medium F2400M with Airmate

15" (381 mm) 5.5" (139 mm) 4" (101 mm) 27" (685 mm) 12" (304 mm) 15.5" (393 mm)

with Rear Deector

15" (381 mm) 6.5" (165 mm) 6" (152 mm) 27" (685 mm) 13" (330 mm) 17.5" (444 mm)

Medium S2400M Step Stove

15" (381 mm) 5.5" (139 mm) 4" (101 mm) 27" (685 mm) 12" (304 mm) 17" (432 mm)

12 | Regency 2400 Freestanding Woodstove

installation

Floor Protection

(Ember Protection only required)

A combustible ﬂoor must be protected by non-combustible

material (like tile, concrete board, or certiﬁed to UL-1618 or

as deﬁned by local codes) extending beneath the heater and

a minimum of 6" (152mm) from each side and minimum 16"

(406mm) from the front face of the stove and minimum 6"

(or the rear clearance to combustibles whichever is smaller)

from the rear of the stove.

When installed with horizontal venting, non-combustible ﬂoor

protection must beneath the ﬂue pipe and extend 2" (51mm)

beyond each side.

Minimum Overall Width (X) of Floor

Protector for all installations:

Stove F2400M 36" (914 mm)

Step Stove S2400M 36" (914 mm)

NOTE: In Canada, oor protection must extend 18" (450mm) to the

front and 8" (200mm) to each side and back of the stove.

Minimum Alcove Clearance and Clearance to Combustible Materials

The Regency Freestanding models have been alcove approved and must be installed

with a listed double wall connector to the ceiling level.

Note: Minimum alcove ceiling height - 84"

Maximum depth of alcove - 36"

NOTE: This clearance is also required for air space between the appliance and wall/ceiling.

Unit From Unit From Corner From Flue Center-Line

G H I J K L

Medium F2400M with Airmate

15" (381 mm) 5.5" (139 mm) 27" (685 mm) 12" (304 mm) 54" (1371 mm) 48" (1219 mm)

with Rear Deector

15" (381 mm) 6.5" (165 mm) 27" (685 mm) 13" (330 mm) 54" (1371 mm) 49" (1244 mm)

Medium S2400M Step Stove

15" (381 mm) 5.5" (139 mm) 27" (685 mm) 12" (304 mm) 54" (1371 mm) 48" (1219 mm)

Minimum Overall Depth (Y) of Floor Protector

Unit Residental `C`Vent Residential

Close Clearance

Mobile Home

Close Clearance

Alcove

Y Z Y Z Y Z Y

Medium F2400M with Airmate

46" (1168 mm) 6" (152 mm) 45"* (1143 mm) 5" (127 mm) 45" (1143 mm) 5" (127 mm) 45"* (1143 mm) 5" (127 mm)

with Rear Deector

46" (1168 mm) 6" (152 mm) 45" (1143 mm) 5" (127 mm) 45" (1143 mm) 5" (127 mm) 45"* (1143 mm) 5" (127 mm)

Medium S2400M Step Stove

46" (1168 mm) 6" (152 mm) 45"* (1143 mm) 5" (127 mm) 45" (1143 mm) 5" (127 mm) 45"* (1143 mm) 5" (127 mm)

* The rear clearance to combustibles is less than 6" (for corner installations the rear corners may be angled to take advantage of the closer clearances).

Regency 2400 Freestanding Woodstove | 13

installation

Cover

Plate

Blanking

Plate

Pedestal

Washer

Bolt

Pedestal

Door

Cover

Plate

Diagram 2

Diagram 3

STOVE ASSEMBLY

PRIOR TO

INSTALLATION

All units require either the pedestal or 4 legs at-

tached to the base. The F2400M stove requires

either the Airmate or Rear Heat Deﬂector on top

of the stove. Clearances to combustible materials

vary depending on whether the airmate or rear

heat deﬂector is installed, so be sure to check

the Minimum Clearances, Installation section.

Airmate Assembly for F2400M

(850-105)

1) The airmate sits on top of the stove with

the slots in the sides ﬁtting over the curved

deﬂector on the rear stove top. See diagram

1. Discard the Rear Heat Deﬂector that is

supplied with the unit, it is not required if the

airmate is installed.

2) Center the airmate and push it forward to the

front of the stove. The back of the airmate

should be level with the back and sides of

the rear heat shield. See Diagrams 2 & 3.

Rear Heat Deector

Assembly for F2400M

(815-555)

The rear heat deﬂector is supplied with the stove

and must be installed unless the optional airmate

has been selected. It stops the heat radiated

from the ﬂue collar from overheating the rear

wall. The rear heat deﬂector is installed on top

of the rear heat shield, as shown in Diagram 4.

Side Shield Adjustment

The left and right side shields are lowered for

shipping and handling. It allows for a handhold

on the top of the stove. Before placing in the

Step Stove in its ﬁnal position, the side shields

must be raised.

Loosen the screws on the rear on the stove (3

per side), slide the side panel up as far as pos-

sible and then secure by tightening the screws.

Pedestal Assembly

F2400M & S2400M

(020-925)

1) For easier assembly, tip the stove on its back

(onto a soft surface to prevent scratching).

Hint: If you have chosen the Ash Drawer

option, remove the ash dump cover plates

(knockout) before attaching the pedestal.

See page 17 "Ashdrawer Kit Installation".

2) Important: Remove the blanking plate if

a) you are not installing outside combustion

air or

b) outside air is to be brought in from the

rear of the stove (see below).

3) Unscrew the 4 bolts in the under-side of the

stove. Align the holes in the corners of the

pedestal top with the corresponding holes

in the base of the stove. Fasten using a bolt

and washer for each corner.

4) Push the

Regency logo

into the two

holes in the

front bottom

left corner of

the pedestal

cover plate.

Note: Any paint touch up should be done

prior to placing logo on pedestal.

5) If not using ash drawer, then cover plate must

be installed. If using ash drawer, then disregard

cover plate.

Side Shield

Diagram 1

Diagram 4

Shown with classic door

14 | Regency 2400 Freestanding Woodstove

installation

* when using single

wall pipe

Horizontal Installation

Standard Ceiling Installation

8) To complete your chimney installation, install

the double wall connector pipe from the

stove’s ﬂue collar to the chimney support

device.

9) If you are using a horizontal connector,

the chimney connector should be as high

as possible while still maintaining the 18"

(457mm) minimum distance from the hori-

zontal connector to the ceiling.

10) NOTE: Residential Close Clearance and

Alcove installations require a listed dou-

ble wall connector from the stove collar

to the ceiling level.

The diagrams below illustrate one way to install

your unit into a standard ceiling or with a horizon-

tal connector. Check with your dealer or installer

for information on other options available to you.

STEP-BY-STEP

CHIMNEY AND

CONNECTOR

INSTALLATION

Note: These are a generic set of chimney in-

stallation instructions. Always follow

the manufacturers own instructions

explicitly. Verify the Minimum Recom-

mended Heights for Woodstove Flue

(Table 1 in the Installation section).

1) With your location already established, cut

and frame the roof hole. It is recommended

that no ceiling support member be cut for

chimney and support box installation. If it is

necessary to cut them, the members must

be made structurally sound.

2) Install radiant shield and support from above.

3) Stack the insulated pipe onto your ﬁnish

support to a minimum height of 3 feet above

the roof penetration, or 2 feet above any

point within 10 feet measured horizontally.

There must be at least 3 feet of chimney

above the roof level.

Note: Increasing the chimney height above

this minimum level will sometimes

help your unit to “breathe” better

by allowing a greater draft to be cre-

ated. This greater draft can decrease

problems such as, dicult start-ups,

back-smoking when door is open, and

dirty glass. It might be sucient to

initially try with the minimum required

height, and then if problems do arise

add additional height at a later date.

4) Slide the roof ﬂashing over your chimney

and seal the ﬂashing to the roof with rooﬁng

compound. Secure the ﬂashing to your roof

with nails or screws.

5) Place the storm collar over the ﬂashing,

sealing the joints with a silicone caulking.

6) Fasten the raincap with spark screens (if

required) to the top of your chimney.

7) For optimum efﬁciency when installing into

a masonry chimney, size accordingly, i.e.

the 6" (152mm) ﬂue dia. is 28.28 sq.in.

Leg and Bottom Shield Assembly

F2400M & S2400M

Bottom Shield 020-911

Legs (set of 4)

Cast - Painted Black 850-126

Cast - Brushed Nickel 850-128

The instructions below apply to the steel leg,

painted cast leg and the gold plated cast leg. It

will be easier to attach the legs to the stove if

the stove is tipped on its back (preferably on a

soft surface to prevent scratching). Ensure to be

extremely careful when tipping stove.

Important: Prior to installing the bottom hat

shield, remove the 4 inch blanking plate. See

below. This must be removed for combustion

air to enter the appliance.

1) Remove the 4 bolts from underside of the

base of the pedestal and discard. Also

remove cover plate and put to the side.

2) Line up the heat shield with the bottom of

the unit.

3) Start threading the bolt and washer (supplied

with the bottom shield) for about 1/4 of the

way through the leg with the washers being

underneath the legs. Ensure that the legs

are properly aligned with heat shield and

tighten the bolts.

4) Level the stove by adjusting the levelling

bolts in the bottom of each leg.

5) Reinstall cover plate.

6) Install logo plate onto heat shield by placing

in 2 holes as shown in diagram.

If you are installing outside combustion air, bend

the tabs out 90 degrees. Pipe fresh air into the

bottom shield by using a minimum 4" duct pipe

with a mesh grill at the outside termination. At-

tach the pipe to the 2 tabs with screws.

Bottom Shield

Cover

Plate

Tabs

Spacer

Leg

Leveling

Bolt

Washer

Logo

Plate

Bolt

Screw

Blanking Plate

Regency 2400 Freestanding Woodstove | 15

installation

FACTORY

BUILT CHIMNEY

When a metal prefabricated chimney is used, the manufacturer's installation instructions must be followed. You must also purchase and install the

ceiling support package or wall pass-through and "T" section package, ﬁrestops (where needed), insulation shield, roof ﬂashing, chimney cap, etc.

Maintain proper clearance to the structure as recommended by the manufacturer. The chimney must be the required height above the roof or other

obstructions for safety and proper draft operation.

MASONRY

CHIMNEY

Ensure that a masonry chimney meets the mini-

mum standards of the National Fire Protection

Association (NFPA) by having it inspected by

a professional. Make sure there are no cracks,

loose mortar or other signs of deterioration and

blockage. Have the chimney cleaned before the

stove is installed and operated. When connect-

ing the stove through a combustible wall to a

masonry chimney, special methods are needed.

MASONRY

FIREPLACE

There are listed kits available to connect a stove

to a masonry ﬁreplace. The kit is an adapter

that is installed at the location of the ﬁreplace

damper. The existing damper may have to be

removed to allow installation.

This unit is designed to use either a 5.5" (140mm)

or 6" (152mm) ﬂue liner only within the conﬁnes

of the masonry chimney as shown.

Minimum 18" (457mm)

to centerline

Minimum

18"

(457mm

)

centerline

When referencing installation or connection to

masonry ﬁreplaces or chimneys, the masonry

construction must or shall be code complying.

When referencing installation or connection to

masonry ﬁreplaces or chimneys, the masonry

construction must or shall be code complying.

16 | Regency 2400 Freestanding Woodstove

installation

Method A: 12" (304.8 mm) Clearance to Combustible Wall

Member:

Using a minimum thickness 3.5" (89 mm) brick and a 5/8" (15.9 mm)

minimum wall thickness clay liner, construct a wall pass-through.

The clay liner must conform to ASTM C315 (Standard Specication

for Clay Fire Linings) or its equivalent. Keep a minimum of 12" (304.8

mm) of brick masonry between the clay liner and wall combustibles.

The clay liner shall run from the brick masonry outer surface to the

inner surface of the chimney ue liner but not past the inner surface.

Firmly grout or cement the clay liner in place to the chimney ue liner.

Method B: 9" (228.6 mm) Clearance to Combustible Wall Member:

Using a 6" (152.4 mm) inside diameter, listed, factory-built Solid-Pak

chimney section with insulation of 1" (25.4 mm) or more, build a wall

pass-through with a minimum 9" (228.6 mm) air space between the

outer wall of the chimney length and wall combustibles. Use sheet

metal supports fastened securely to wall surfaces on all sides, to

maintain the 9" (228.6 mm) air space. When fastening supports to

chimney length, do not penetrate the chimney liner (the inside wall

of the Solid-Pak chimney). The inner end of the Solid-Pak chimney

section shall be ush with the inside of the masonry chimney ue, and

sealed with a non-water soluble refractory cement. Use this cement

to also seal to the brick masonry penetration.

Minimum

12 in. (304.8mm)

to combustibles

Masonry chimney

Chimney Flue

Minimum chimney clearance to brick

and combustibles 2 in. (50.8mm)

Minimum clearance

12 in. (304.8mm)

of brick

Chimney

connector

Fire clay

liner

Method C: 6" (152.4 mm) Clearance to Combustible Wall Member:

Starting with a minimum 24 gage (.024" [.61 mm]) 6" (152.4 mm) metal

chimney connector, and a minimum 24 gage ventilated wall thimble

which has two air channels of 1" (25.4 mm) each, construct a wall

pass-through. There shall be a minimum 6" (152.4) mm separation area

containing berglass insulation, from the outer surface of the wall thimble

to wall combustibles. Support the wall thimble, and cover its opening

with a 24-gage minimum sheet metal support. Maintain the 6" (152.4

mm) space. There should also be a support sized to t and hold the

metal chimney connector. See that the supports are fastened securely

to wall surfaces on all sides. Make sure fasteners used to secure the

metal chimney connector do not penetrate chimney ue liner.

Method D: 2" (50.8 mm) Clearance to Combustible Wall Member:

Start with a solid-pak listed factory built chimney section at least

12" (304 mm) long, with insulation of 1" (25.4 mm) or more, and an

inside diameter of 8" (2 inches [51 mm] larger than the 6" [152.4

mm] chimney connector). Use this as a pass-through for a minimum

24-gage single wall steel chimney connector. Keep solid-pak section

concentric with and spaced 1" (25.4 mm) o the chimney connector

by way of sheet metal support plates at both ends of chimney section.

Cover opening with and support chimney section on both sides with

24 gage minimum sheet metal supports. See that the supports are

fastened securely to wall surfaces on all sides. Make sure fasteners

used to secure chimney ue liner.

COMBUSTIBLE WALL CHIMNEY

CONNECTOR PASS-THROUGHS

Regency 2400 Freestanding Woodstove | 17

installation

RECOMMENDED HEIGHTS FOR WOODSTOVE FLUE

Simple rules on draft (refer to Table 1).

1) At sea level minimum height is 12' straight.

2) Add the following vertical height to compen-

sate for:

45 deg. elbow = 1 ft.

90 deg. elbow = 2 ft.

"T" = 3 ft.

Each foot of horizontal run = 2 ft.

3) Add 4% overall for each 1000' above sea

level.

Example: a)

1-1/2 ft. of horizontal run = 3 ft.

one "T" = 3 ft.

Total Addition (at sea level) = 6 ft.

Example: b)

One 90 deg. elbow = 2 ft.

2 ft. of horizontal run = 4 ft.

one "T" = 3 ft.

Total Addition (at sea level) = 9 ft.

Recommended Flue Height

Elevation Example a) Example b)

0' 18' 21'

1000' 18.72' 21.84'

2000' 19.44' 22.68'

5000' 21.60' 25.20'

8000' 23.76' 27.72'

Draft is the force which moves air from the appliance up through the chimney. The amount of draft in your chimney depends on the length of the chimney, local

geography, nearby obstructions and other factors. Too much draft may cause excessive temperatures in the appliance and may cause damage. An uncontrol-

lable burn or excessive temperature indicates excessive draft. Inadequate draft may cause back pufﬁng into the room and plugging of the chimney. Inadequate

draft will cause the appliance to leak smoke into the room through appliance and chimney connector joints. Ensure the heater is installed in areas that are not

too close to neighbors or in valleys that would cause unhealthy air quality or nuisance conditions.

MINIMUM RECOMMENDED FLUE HEIGHTS IN FEET

(Measured from the top of the unit)

ELEVATION (FT)

ABOVE SEA LEVEL

# OF ELBOWS

0 2 x 15

4 x 15

2 x 30

4 x 30

2 x 45

4 x 45

0-1000 12.0 13.0 14.0 15.0 18.0 16.0 20.0

1000-2000 12.5 13.5 14.5 15.5 19.0 16.5 21.0

2000-3000 13.0 14.0 15.0 16.0 19.5 17.0 21.5

3000-4000 13.5 14.5 15.5 17.0 20.0 18.0 22.5

4000-5000 14.0 15.0 16.0 17.5 21.0 18.5 23.0

5000-6000 14.5 15.5 17.0 18.0 21.5 19.0 24.0

6000-7000 15.0 16.0 17.5 18.5 22.5 20.0 25.0

7000-8000 15.5 16.5 18.0 19.0 23.0 20.5 25.5

8000-9000 16.0 17.0 18.5 20.0 24.0 21.0 26.5

9000-10000 16.5 17.5 19.0 20.5 24.5 22.0 27.0

NOTE: No more than two offsets (four elbows) allowed. Two 45

elbows equal one 90

elbow.

18 | Regency 2400 Freestanding Woodstove

installation

MOBILE HOME INSTALLATION

Once you have properly marked the position of

your unit and the ﬂoor protection as outlined in

the Residential Installation items #1 through #8,

a supply of fresh air has to be supplied to your

unit. Cut a minimum 4" (102mm) diameter hole

through your ﬂoor protector and the ﬂoor directly

under your pedestal base to the outside. Use 4"

(102mm) duct pipe with a mesh grill to pipe fresh

air into the pedestal area. Block off the hole in

the back of the pedestal with the square plate

and the two 1/2" screws provided.

Place your unit in position and secure it to the

ﬂoor using two lag bolts 3/8" (10mm) x 3-1/2"

(89mm) through the two holes inside the pedestal

base. It is important to maintain the structural

integrity of the Mobile Home ﬂoor, walls and roof

when installing your unit.

For Mobile Home units installed in the U.S. the

unit must be grounded using a #8 ground wire

with approved termination and star washer.

In addition to standard installation instructions the

following requirements are mandatory for installa-

tion in a mobile home.

1) The stove must be permanently bolted to

the ﬂoor of the Mobile Home using the ﬂoor

screws provided.

2) The stove must have a permanent outside air

source for combustion.

3) The stove must be electrically grounded to the

steel chassis of the Mobile Home.

4) A listed double-wall connector chimney system,

roof thimble, spark arrestor and roof ﬂashing kit

suitable for use in Mobile Homes must be used.

5) If the chimney exits the Mobile Home at a loca-

tion other than through the roof, and exits at a

point 7ft. (2130mm) or less above the ground

level on which the Mobile Home is positioned

a guard or method of enclosing the chimney

shall be ﬁtted at the point of exit for a height up

to 7ft. (2130mm).

6) The chimney shall be attached directly to the

room heater and shall extend at least 3 ft.

(914mm) above the part of the roof through

which it passes. The top of the chimney should

project at least 2ft. (610mm) above the highest

elevation of any part of the Mobile Home within

10 ft. (3048mm) of the chimney.

7) The chimney system shall comply with Local

Requirements.

8) Any openings in a chimney guard where required

must not permit the entrance of 3/4" (19mm)

diameter rod.

9) CAUTION: THE STRUCTURAL INTEGRITY OF

THE MOBILE HOME ROOF, FLOOR, WALLS

AND CEILING MUST BE MAINTAINED.

10) Check any other local building code as other

local codes may apply.

11) WARNING: DO NOT INSTALL IN A SLEEPING

ROOM OF A MOBILE HOME.

12) Use silicone to create an effective vapour

barrier at the location where the chimney or

other component penetrates to the exterior of

the structure.

CAUTION: At no time use unlabelled parts,

or substitute parts made for another chim-

ney system.

Install as per chimney manufacturer's

installation instructions.

WARNING: Operate only with door fully

closed - open feed door to feed ﬁre only.

Regency 2400 Freestanding Woodstove | 19

installation

Slide the tube into the left hand side, as far

as possible and then bring it back into the

hole on the right hand side until it locks into

position. If the tube will not slide in easily,

simply use a pair of vise grips or pliers and

tap it into place with a hammer. A tighter ﬁt

will ensure the tube will not move when the

unit is burning.

2) Slide the left bafﬂe over the air tubes from

the front and then push it to the back.

SIMPSON DURA-PLUS

Qty.Part # Description

1 6DVL8693 Connector Kit

1 6DP-MH9096 Mobile Home Kit

ICC EXCEL 2100

Qty.Part # Description

1 6CL48 48" Chimney length (also in

12", 18", 24" lengths.)

1 6RC Rain Cap

1 6RCS Spark Screen (for rain cap)

1 6RDS/SQS Round/Square support box

1 6VF Flashing

1 6UBA "Ultrablack" Close Clearance

Connector

Canadian Installations*

SECURITY S2100 (see above for details)

ICC EXCEL 2100 (see above for details)

SELKIRK SENTINAL CF

*The use of alternate pitch ﬂashings, support

box extensions, additional chimney lengths, and

additional chimney bracing, may be used on each

of the previously listed systems. These parts

though must be from the same system as listed,

and must be a similar and/or complimentary part.

CAUTION: At no time use unlabelled

parts, or substitute parts made for

another chimney system.

Install as per chimney manufacturer's instal-

lation instructions.

FLUE BAFFLE &

SECONDARY AIR TUBE

INSTALLATION

The ﬂue bafﬂe system located in the upper area

of the ﬁrebox is removable to make cleaning

your chimney system easier. The bafﬂes must

be installed prior to your ﬁrst ﬁre. Smoke spill-

age and draft problems may occur if the

bafﬂes are improperly positioned. Check

the position of the bafﬂes on a regular basis as

they can be dislodged if too much fuel is forced

into the ﬁrebox.

Freestanding Stove

F2400M

The unit arrives with the 2 bafﬂes on the ﬂoor

of the ﬁrebox.

1) If all 4 air tubes are installed continue on to

Step 2), if not, follow the instructions below.

Install the air tube into the holes in the side

channels. The notch goes on the right hand

side with the air holes facing toward the door.

LISTED COMPONENTS

FOR MOBILE HOME

INSTALLATION

The Regency F2400M and S2400M Freestand-

ing pedestal units are approved for installation

in a Mobile Home if one of the following pipe

systems is used.

U.S. Installation*

METALBESTOS SSII

Qty. Part # Description

1 6DS-VK Connector Kit

1 6TMH Shield/Support

1 6TAF-6 Flashing

1 6T-36 Chimney Length

1 6T-18 Chimney Length

1 6T-CT Rain Cap

PRO-JET 3103

Qty.Part # Description

1 PV06-TK Connector

1 CSB Shield/Support

1 RRS Radiation Shield

1 LFR03 Flashing

1 SL3 Chimney Length

1 SL1 Chimney Length

1 RCSA Rain Cap

SECURITY ASHT

Qty.Part # Description

1 DL42A-6 Connector Kit

1 6SS Shield/Support

1 6FAMH Flashing

1 6L3 Chimney Length

1 6L1 Chimney Length

1 CPE Rain Cap

SECURITY S2100

Qty.Part # Description

1 DL42A-6 Connector Kit

1 6XSF Support

1 6XFA Flashing

1 6XL3 Chimney Length

1 6XL18 Chimney Length

1 6XCPE Rain Cap

METAL-FAB TEMP/GUARD 2100

Qty.Part # Description

1 6DWBK Connector

1 6TGRS Roof Support

1 6TGG36 Chimney Length

1 6TGG12 Chimney Length

1 6TGF Flashing

1 6TGC Rain Cap

AMERI-TEC HS

Qty.Part # Description

1 6DCC Connector

1 6HSRS-12 Roof Support

(6PLRS-12-BK)

1 6F Flashing

1 6HS-36 Chimney Length

1 6HS-18 Chimney Length

1 6HS-RCS Rain Cap (6PL-MPC)

3) Tilt the left bafﬂe up on top of the side chan-

nel and it will leave enough room to position

the right bafﬂe in the same manner as Step

1) above. Then reposition the left bafﬂe ﬂat

on the air tubes.

4) Important: push both bafﬂes so they are

tight against the side walls.

Note: When getting the chimney cleaned,

push the baes forward toward the

front of the stove, this should leave

sucient access to the ue. If it is

not enough space then remove the

middle air tube (reverse the procedure

in step 1) above), and bae and then

replace everything when cleaning is

completed.

Side View

Front View

20 | Regency 2400 Freestanding Woodstove

installation

STAINLESS STEEL SMOKE DEFLECTOR ADJUSTMENT / REPLACEMENT

The stainless smoke deﬂector is located in the upper front area of the ﬁrebox. The deﬂector is held in place with 2 bolts

Prior to the ﬁrst ﬁre, ensure deﬂector is seated properly and secured with 2 hand tightened bolts.

To replace the deﬂector, loosen off both bolts and slide defector upward and out. Install new defector and hand tighten bolts. Ensure positive location of the

deﬂector prior to hand tightening.

WARNING: Operation of the unit with out proper installation of smoke deﬂector will void warranty.

Smoke deector installed with 2 bolts.

Note: This is a view from the back of the unit

through the top.

Ensure defector is seated so bolts are situated

at the top of the keyhole before tightening.

Hand tighten bolts only.

Smoke deector

La page charge ...