Maytag EPIC MGD9700S Mode d'emploi

Catégorie
Sèche-linge
Taper
Mode d'emploi
MAYI'AG ®
TM
EPIC
FRONT-LOADING GAS DRYER
I ¸ r, _ _ • "_ ....._ _
k)_i o_- (_[:_;I:_]"(.: tl;l(l?'
For questions about features, operation/performance, parts, accessories or service, call: 1-800-688-9900
In Canada, call : 1-800-807-6777 or visit our website at...
www.maytag.com or www.maytag.ca
SECADORA A GAS DE CARGA FRONTAL
Si tiene preguntas respecto a las caracteristicas, funcionamiento/rendimiento, piezas, accesorios o servicio t_cnico,
Name al: 1-800-688-9900
o visite nuestro sitio web en...www.maytag.com
SECHEUSE A GAZ A CHARGEMENT
FRONTAL
Au Canada, composez le 1-800-807-6777
ou visitez notre site web &...www.maytag.ca
Table of Contents/indice/Table des matieres .................................................................. 2
W10099060A
TABLE OF CONTENTS
DRYER SAFETY .............................................................................. 3
INSTALLATION INSTRUCTIONS .................................................. 5
Tools and Parts ............................................................................ 5
Options ......................................................................................... 5
Location Requirements ................................................................ 6
Electrical Requirements ............................................................... 8
Gas Supply Requirements ........................................................... 8
Venting Requirements .................................................................. 9
Plan Vent System ....................................................................... 10
Install Vent System ..................................................................... 12
Install Leveling Legs ................................................................... 12
Make Gas Connection ............................................................... 12
Connect Vent .............................................................................. 13
Level Dryer ................................................................................. 13
Reverse Door Swing .................................................................. 13
Complete Installation ................................................................. 15
DRYER USE .................................................................................. 16
Starting Your Dryer ..................................................................... 16
Stopping Your Dryer .................................................................. 17
Pausing or Restarting ................................................................. 17
Control Locked ........................................................................... 17
Drying and Cycle Tips ................................................................ 17
Status Lights .............................................................................. 18
Cycles ......................................................................................... 18
Additional Features .................................................................... 19
Drying Rack ................................................................................ 20
DRYER CARE .............................................................................. 21
Cleaning the Dryer Location ...................................................... 21
Cleaning the Lint Screen ............................................................ 21
Cleaning the Dryer Interior ......................................................... 21
Removing Accumulated Lint ...................................................... 21
Vacation and Moving Care ......................................................... 22
Changing the Drum Light ........................................................... 22
TROUBLESHOOTING .................................................................. 22
ASSISTANCE OR SERVICE ......................................................... 24
WARRANTY .................................................................................. 25
P
INDICE
SEGURIDAD DE LA SECADORA ................................................ 26
INSTRUCCIONES DE INSTALACION ......................................... 27
Herramientas y piezas ................................................................ 27
Opciones .................................................................................... 28
Requisitos de ubicaci6n ............................................................. 28
Requisitos electricos .................................................................. 31
Requisitos del suministro de gas ............................................... 31
Requisitos de ventilacidn ........................................................... 32
Planificacidn del sistema de ventilacidn .................................... 34
Instalacidn del sistema de ventilacidn ....................................... 35
Instalacidn de las patas niveladoras .......................................... 35
Conexidn del suministro de gas ................................................ 36
Conexidn del ducto de escape .................................................. 36
Nivelacidn de la secadora .......................................................... 37
Cdmo invertir el cierre de la puerta ............................................ 37
Complete la instalaci6n .............................................................. 39
USO DE LA SECADORA .............................................................. 40
Puesta en marcha de la secadora ............................................. 40
Detenci6n de la marcha de la secadora .................................... 41
Pausa o reanudaci6n de la marcha ........................................... 41
Control bloqueado ..................................................................... 41
Sugerencias de ciclos y secado ................................................ 41
Luces de estado ......................................................................... 42
Ciclos .......................................................................................... 43
Caracter[sticas adicionales ........................................................ 44
Estante de secado ...................................................................... 45
CUIDADO DE LA SECADORA .................................................... 46
Limpieza del lugar donde esta la secadora .............................. 46
Limpieza del filtro de pelusa ...................................................... 46
Limpieza del interior de la secadora .......................................... 46
Eliminaci6n de pelusa acumulada ............................................. 46
Cuidado para las vacaciones y la mudanza .............................. 47
Cambio de la luz del tambor ...................................................... 47
SOLUCION DE PROBLEMAS ...................................................... 47
AYUDA O SERVICIO TECNICO ................................................... 49
GARANTIA ..................................................................................... 50
TABLE DES MATIERES
SI_CURITE DE LA SI_CHEUSE .................................................... 51
INSTRUCTIONS D'INSTALLATION ............................................. 52
Outillage et pieces ...................................................................... 52
Options ....................................................................................... 53
Exigences d'emplacement ......................................................... 53
Specifications electriques .......................................................... 55
Specifications de I'alimentation en gaz ..................................... 56
Exigences concernant I'evacuation ........................................... 57
Planification du systeme d'evacuation ...................................... 59
Installation du systeme d'evacuation ......................................... 60
Installation des pieds de nivellement ......................................... 61
Raccordement au gaz ................................................................ 61
Raccordement du conduit d'evacuation ................................... 62
Mise & niveau de la secheuse .................................................... 62
Inversion du sens d'ouverture de la porte ................................. 62
Achever I'installation .................................................................. 64
UTILISATION DE LA SI_CHEUSE ................................................ 65
Mise en marche de la secheuse ................................................ 65
Arr6t de la secheuse ................................................................... 66
Pause ou remise en marche ....................................................... 66
Verrouillage des commandes ..................................................... 66
Conseils pour le sechage et les programmes ........................... 66
Temoins lumineux ...................................................................... 67
Programmes ............................................................................... 67
Caracteristiques supplementaires ............................................. 68
Grille de sechage ........................................................................ 69
ENTRETIEN DE LA SI_CHEUSE ................................................. 70
Nettoyage de I'emplacement de la secheuse ........................... 70
Nettoyage du filtre a charpie ...................................................... 70
Nettoyage de I'interieur de la secheuse ..................................... 71
Retrait de la charpie accumulee ................................................ 71
Precautions a prendre pour les vacances et avant un
demenagement .......................................................................... 71
Changement de I'ampoule d'eclairage du tambour ................. 71
Dr!:PANNAGE ................................................................................. 72
ASSISTANCE OU SERVICE ......................................................... 74
GARANTI E ..................................................................................... 75
DRYER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
WARNING: For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, or to prevent property damage, personal injury, or death.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
- WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Clear the room, building, or area of all occupants.
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency, or
the gas supplier.
In the State of Massachusetts, the following installation instructions apply:
[] Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by
the State of Massachusetts.
[] If using a ball valve, it shall be a T-handle type.
[] A flexible gas connector, when used, must not exceed 3 feet.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,
including the following:
[] Read all instructions before using the dryer.
[] Do not place items exposed to cooking oils in your dryer.
Items contaminated with cooking oils may contribute to
a chemical reaction that could cause a load to catch fire.
[] Do not dry articles that have been previously cleaned in,
washed in, soaked in, or spotted with gasoline, dry-
cleaning solvents, or other flammable or explosive
substances as they give off vapors that could ignite or
explode.
[] Do not allow children to play on or in the dryer. Close
supervision of children is necessary when the dryer is
used near children.
[] Before the dryer is removed from service or discarded,
remove the door to the drying compartment.
[] Do not reach into the dryer if the drum is moving.
[] Do not install or store the dryer where it will be exposed
to the weather.
[] Do not tamper with controls.
[] Do not repair or replace any part of the dryer or attempt
any servicing unless specifically recommended in this
Use and Care Guide or in published user-repair
instructions that you understand and have the skills to
carry out.
[] Do not use fabric softeners or products to eliminate static
unless recommended by the manufacturer of the fabric
softener or product.
[] Do not use heat to dry articles containing foam rubber or
similarly textured rubber-like materials.
[] Clean lint screen before or after each load.
[] Keep area around the exhaust opening and adjacent
surrounding areas free from the accumulation of lint, dust,
and dirt.
[] The interior of the dryer and exhaust vent should be
cleaned periodically by qualified service personnel.
[] See installation instructions for grounding requirements.
SAVE THESE INSTRUCTIONS
IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas
Code, ANSi Z223.1/NFPA 54 or the Canadian Natural Gas and Propane installation Code, CSA B149.1.
The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National
Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.
INSTALLATION INSTRUCTIONS
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
8" or 10" pipe wrench
8" or 10" adjustable
wrench (for gas
connections)
Flat-blade screwdriver
Adjustable wrench that
opens to 1" (2.5 cm) or
hex-head socket wrench
(for adjusting dryer feet)
v4" nut driver or socket
wrench (recommended)
Level
Knife
Vent clamps
Pipe-joint compound
resistant to LP gas
Caulking gun and
compound (for installing
new exhaust vent)
Pliers
Tape measure
Parts supplied
Remove parts packages from dryer drum. Check that all parts are
included.
4 Leveling legs
NOTE: Do not use leveling legs if installing the dryer on a
pedestal.
Parts needed
Check local codes and with gas supplier. Check existing gas
supply, electrical supply and venting. Read "Electrical
Requirements," "Gas Supply Requirements" and "Venting
Requirements" before purchasing parts.
For close-clearance installations between 31.5" (80.01 cm)
and 37" (93.98 cm), see "Plan Vent System" section for
venting requirements.
I_- 37" --_1
(93.98 cm)
Mobile home installations require special parts (listed following)
that may be ordered by calling the dealer from whom you
purchased your dryer. For further information, please refer to the
"Assistance or Service" section of this manual.
Mobile Home Installation Kit. Ask for Part Number 346764.
Metal exhaust system hardware.
Pedestal
Are you placing the dryer on a pedestal? You have the option of
purchasing a pedestal separately for this dryer. You may select a
15.5" (39.4 cm) pedestal. This pedestal will add to the total height
of the dryer for a total height of approximately 53.5" (135.9 cm).
For a garage installation, you will need to place the pedestal at
least 3.5" (8.9 cm) above the floor.
Optional pedestal
To order, call the dealer from whom you purchased your dryer or
refer to the "Assistance or Service" section of this manual.
Pedestal Color Part Number
Height
15.5" (39.4 cm) White WHP1500SQ
15.5" (39.4 cm) Black WH P1500SB
Stack Kit
Are you planning to stack your washer and dryer? To do so, you
will need to purchase a Stack Kit.
To order, call the dealer from whom you purchased your dryer or
refer to the "Assistance or Service" section of this manual. Ask
for Part Number 8212640.
ExplosionHazard
Keep flammable materials and vapors, such as
gasoline, away from dryer,
Place dryer at least 18 inches (46 cm) above the floor
for a garage installation.
Failure to do so can result in death, explosion, or fire.
You will need
A location that allows for proper exhaust installation. A gas
dryer must be exhausted to the outdoors. See "Venting
Requirements."
A grounded electrical outlet located within 2 ft (61 cm) of
either side of the dryer. See "Electrical Requirements."
A sturdy floor to support the total dryer weight of 200 Ibs
(90.7 kg). The combined weight of a companion appliance
should also be considered.
A level floor with a maximum slope of 1" (2.5 cm) under entire
dryer. If slope is greater than 1" (2.5 cm), install Extended
Dryer Feet Kit, Part Number 279810. Clothes may not tumble
properly, and automatic sensor cycles may not operate
correctly if dryer is not level.
For a garage installation, you will need to place the dryer at
least 18" (46 cm) above the floor. If using a pedestal, you will
need 18" (46 cm) to the bottom of the dryer.
Do not operate your dryer at temperatures below 45°F (7°C). At
lower temperatures, the dryer might not shut off at the end of an
automatic cycle. This can result in longer drying times.
The dryer must not be installed or stored in an area where it will
be exposed to water and/or weather.
Check code requirements. Some codes limit, or do not permit,
installation of the dryer in garages, closets, mobile homes or
sleeping quarters. Contact your local building inspector.
NOTE: No other fuel-burning appliance can be installed in the
same closet as a dryer.
Installation clearances
The location must be large enough to allow the dryer door to
open fully.
Dryer Dimensions
51_/2,'
(130.91cm)
*Most installations require a minimum 5" (12.7 cm) clearance
behind the dryer for the exhaust vent with elbow. See "Venting
Requirements."
Installation spacing for recessed area or closet installation
The following spacing dimensions are recommended for this
dryer. This dryer has been tested for spacing of 0" (0 cm)
clearance on the sides and rear. Recommended spacing should
be considered for the following reasons:
Additional spacing should be considered for ease of
installation and servicing.
Additional clearances might be required for wall, door and
floor moldings.
Additional spacing should be considered on all sides of the
dryer to reduce noise transfer.
For closet installation, with a door, minimum ventilation
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are
acceptable.
Companion appliance spacing should also be considered.
Custom undercounter installation - Dryer only
1"* _ _-_27"---_ _-- 1"*
2.5 crn 68.6 cm 2.5 cm
*Required spacing
Closet installation - Dryer only
I1"*_ 31,J;'_ls"**l
48 in.2.
(310 cm 2)
(2.5crn) (80cm) {12.7crn)
A
A. Side view - closet or confined area
B. Closet door with vents
*Required spacing
**For side or bottom venting, O" (Ocm) spacing is allowed.
Recessed or closet installation - Dryer on pedestal
(2.5 cm) (68.6 cm)
A
(2.5 cm) (2.5 cm)
--_ 14" max.*
_ 18I'din.*
1"'1I_-- 31,/;'--_1_"**1
(aocm) (12.7cm)
B
A. Recessed area
B. Side view - closet or confined area
*Required spacing
**For side or bottom venting, O" (Ocm) spacing is allowed.
Recommended installation spacing for cabinet
installation
For cabinet installation, with a door, minimum ventilation
openings in ihe top of the cabinet are required.
_ (17.8c _"_17.8 cm)
7"* (17.8cm) 7"*(17.8 cm)
(12.7 cm) (80.0 cm) (2.5 cm) (2.5 cm)(68.6 cm) (2.5 crn)
*Required spacing
**For side or bottom venting, O" (Ocm) spacing is allowed.
Recommended installation spacing for recessed or
closet installation, with stacked washer and dryer
The dimensions shown are for the recommended spacing.
48 in.2 *
(310 cm 2)
T
o
-- __
24 in? *
(155cm2)
i
3"* (7.6 cm)
T
!
3"* (7.6 crn)
*Required spacing
5"*--_"
(12.7cm)
6"* (_5.2 cm)
l /j..................d/
76"
(193cm) --
_ 1" _ _-27"_
(2.5 cm) 68.6 cm
*Required spacing
Mobile home - Additional installation requirements
This dryer is suitable for mobile home installations. The
installation must conform to the Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD Part 280) or Standard CAN/CSA-Z240
MH.
Mobile home installations require:
Metal exhaust system hardware, which is available for
purchase from your dealer.
Mobile Home Installation Kit Part Number 346764. See "Tools
and Parts" section for information on ordering.
Special provisions must be made in mobile homes to
introduce outside air into the dryer. The opening (such as a
nearby window) should be at least twice as large as the dryer
exhaust opening.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
120 Volt, 60 Hz., AC only, 15- or 20-amp fused electrical
supply is required. A time-delay fuse or circuit breaker is
recommended. It is also recommended that a separate circuit
serving only this dryer be provided.
GROUNDING INSTRUCTIONS
For a grounded, cord-connected dryer:
This dryer must be grounded. In the event of malfunction or
breakdown, grounding will reduce the risk of electric shock
by providing a path of least resistance for electric current.
This dryer is equipped with a cord having an equipment-
grounding conductor and a grounding plug. The plug must
be plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local codes
and ordinances.
WARNING: Improper connection of the equipment-
grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service representative
or personnel if you are in doubt as to whether the dryer is
properly grounded. Do not modify the plug provided with the
dryer: if it will not fit the outlet, have a proper outlet installed
by a qualified electrician.
SAVE THESE INSTRUCTIONS
Explosion Hazard
Use a new CSA international approved gas supply line.
Install a shut-off valve.
Securely tighten all gas connections.
If connected to LP, have a qualified person make sure
gas pressure does not exceed 13" (33 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel,
Failure to do so can result in death, explosion, or fire.
Gas Type
Natural gas:
This dryer is equipped for use with Natural gas. It is design-
certified by CSA International for LP (propane or butane) gases
with appropriate conversion.
Your dryer must have the correct burner for the type of gas in
your home. Burner information is located on the rating plate
in the door well of your dryer. Ifthis information does not
agree with the type of gas available, contact your dealer or
call the phone numbers referenced in the "Assistance or
Service" section of this manual.
LP gas conversion:
Conversion must be made by a qualified technician.
No attempt shall be made to convert the appliance from the gas
specified on the model/serial rating plate for use with a different
gas without consulting your gas company.
Gas supply line
Must include W' NPT minimum plugged tapping accessible
for test gauge connection, immediately upstream of the gas
connection to the dryer. See illustration.
W' IPS pipe is recommended.
%" approved aluminum or copper tubing is acceptable for
lengths under 20 ft (6.1 m) if local codes and gas supplier
permit.
If you are using Natural gas, do not use copper tubing.
Lengths over 20 ft (6.1 m) should use larger tubing and a
different size adapter fitting.
IfyourdryerhasbeenconvertedtouseLPgas,%"LP
compatiblecoppertubingcanbeused.Ifthetotallengthof
thesupplylineismorethan20ft(6.1m),uselargerpipe.
NOTE:Pipe-jointcompoundsthatresisttheactionofLPgas
mustbeused.DonotuseTEFLON°ttape.
Mustincludeashutoffvalve:
In the U.S.A.:
An individual manual shutoff valve must be installed within
six (6)feet (1.8 m) of the dryer in accordance with the National
Fuel Gas Code, ANSI Z223.1.
In Canada:
An individual manual shutoff valve must be installed in
accordance with the B149.1, Natural Gas and Propane
Installation Code. It is recommended that an individual
manual shutoff valve be installed within six (6) feet (1.8 m)
of the dryer.
The location should be easy to reach for opening and closing.
A C E
B D
A. %" flexible gas connector
B. %" pipe to flare adapter fitting
C. Vs"NPT minimum plugged tapping
D. Y;" NPT gas supply line
E. Gas shutoff valve
Gas supply connection requirements
Use an elbow and a 3/8"flare x %" NPT adapter fitting
between the flexible gas connector and the dryer gas pipe, as
needed to avoid kinking.
Use only pipe-joint compound. Do not use TEFLON _t tape.
This dryer must be connected to the gas supply line with a
listed flexible gas connector that complies with the standard
for connectors for gas appliances, ANSI Z21.24 or CSA 6.10.
Burner input requirements
Elevations above 10,000 ft (3,048 m):
When installed above 10,000 ft (3,048 m) a 4% reduction of
the burner Btu rating shown on the model/serial number plate
is required for each 1,000 ft (305 m) increase in elevation.
Gas supply pressure testing
The dryer must be disconnected from the gas supply piping
system during pressure testing at pressures greater than
1/2psi.
Dryer gas pipe
The gas pipe that comes out through the rear of your dryer
has a %" male pipe thread.
A. Y2"NPT gas supply line
B. %" NPT dryer pipe
*NOTE: Ifthe dryer is mounted on a pedestal, the gas pipe height
must be an additional 10" (25.4 cm) or 15.5" (39.4 cm) from the
floor, depending on the pedestal model. For a garage
installation, the gas pipe height must be an additional
18" (46 cm) from the floor.
Fire Hazard
Use a heavy metal vent.
Do not use a plastic vent.
Do not use a metal foil vent.
Failure to follow these instructions can result in death
or fire.
WARNING; To reduce the risk of fire, this dryer MUST BE
EXHAUSTED OUTDOORS.
IMPORTANT: Observe all governing codes and ordinances.
The dryer exhaust must not be connected into any gas vent,
chimney, wall, ceiling or a concealed space of a building.
If using an existing vent system
Clean lint from the entire length of the system and make sure
exhaust hood is not plugged with lint.
Replace any plastic or metal foil vent with rigid or flexible
heavy metal vent.
Review Vent system chart. Modify existing vent system if
necessary to achieve the best drying performance.
1-®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.
If this is a new vent system
Vent material
Use a heavy metal vent. Do not use plastic or metal foil vent.
4" (10.2 cm) heavy metal exhaust vent and clamps must be
used.
4" (lO.2 cm) heavymetal exhaust vent
Vent products can be purchased from your dealer or by
calling Maytag Services. For more information, see the
"Assistance or Service" section of this manual.
Rigid metal vent
For best drying performance, rigid metal vents are
recommended.
Rigid metal vent is recommended to avoid crushing and
kinking.
Flexible metal vent
Flexible metal vents are acceptable only if accessible for
cleaning.
Flexible metal vent must be fully extended and supported
when the dryer is in its final location.
Remove excess flexible metal vent to avoid sagging and
kinking that may result in reduced airflow and poor
performance.
Do not install flexible metal vent in enclosed walls, ceilings or
floors.
Elbows
45° elbows provide better airflow than 90° elbows.
Clamps
Good Better
Use clamps to seal all joints.
Exhaust vent must not be connected or secured with screws
or other fastening devices that extend into the interior of the
duct. Do not use duct tape.
Clamp
Exhaust
Recommended hood styles are shown here.
(10.2cm)
A. Louvered hood style
B.Box hood style
The angled hood style (shown here) is acceptable.
4"
(10.2 cm)__
An exhaust hood should cap the vent to keep rodents and
insects from entering the home.
Exhaust hood must be at least 12" (30.5 cm) from the ground
or any object that may be in the path of the exhaust (such as
flowers, rocks or bushes, snow line, etc.).
Do not use an exhaust hood with a magnetic latch.
Improper venting can cause moisture and lint to collect
indoors, which may result in:
[] Moisture damage to woodwork, furniture, paint, wallpaper,
carpets, etc.
[] Housecleaning problems and health problems.
ti:>;_1 _;, ,,_
Choose your exhaust installation type
Recommended exhaust installations
Typicalinstallations vent the dryer from the rear of the dryer.
Other installations are possible,
B
A--
A. Dryer
B. Elbow
C. Wall
D. Exhaust hood
.............. C
E
F
........................................e
....................................H
E. Clamps
F. Rigid metal or flexible metal vent
G. Vent length necessary to connect elbows
H. Exhaust outlet
10
Optional exhaust installations
This dryer can be converted to exhaust out the right side, left side
or through the bottom. If you prefer, you may contact your local
dealer to have the dryer converted,
Fire Hazard
Cover unused exhaust holes with one of the
following kits:
279818 (white)
279820 (black)
Contact your local dealer.
Failure to fellow these instructions can result in death,
fire, electrical shock, or serious injury.
A
B C
A. Standard rear offset exhaust installation
B. Left or right side exhaust installation
C. Bottom exhaust installation
Alternate installations for close clearances
Venting systems come in many varieties. Select the type best for
your installation, Two close-clearance installations are shown.
Refer to the manufacturer's instructions,
"i--- i L
i i .
// I i J
ii
L Js
A B
A. Over-the-top installation (also available with one
offset elbow)
B. Periscope installation
NOTE: The following kits for close clearance alternate
installations are available for purchase. Please see the
"Assistance or Service" section of this manual to order.
Over-the-Top Installation:
Part Number 4396028
Periscope Installation (For use with dryer vent to wall vent
mismatch):
Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm)
mismatch
Part Number 4396011 - 18" (45.72 cm) to 29" (73.66 cm)
mismatch
Part Number 4396014 - 29" (73.66 cm) to 50" (127 cm)
mismatch
Special provisions for mobile home installations
The exhaust vent must be securely fastened to a noncombustible
portion of the mobile home structure and must not terminate
beneath the mobile home. Terminate the exhaust vent outside.
Determine vent path
Select the route that will provide the straightest and most
direct path outdoors.
Plan the installation to use the fewest number of elbows and
turns.
When using elbows or making turns, allow as much room as
possible.
Bend vent gradually to avoid kinking.
Use the fewest 90° turns possible.
Determine vent length and elbows needed for best
drying performance
Use the following Vent system chart to determine type of vent
material and hood combinations acceptable to use.
NOTE: Do not use vent runs longer than those specified in
the Vent system chart. Exhaust systems longer than those
specified will:
Shorten the life of the dryer.
Reduce performance, resulting in longer drying times and
increased energy usage.
The Vent system chart provides venting requirements that will
help to achieve the best drying performance.
11
Vent system chart
NOTE: Side and bottom exhaust installations have a 90° turn
inside the dryer. To determine maximum exhaust length, add one
90° turn to the chart,
Number of Type of Box or Angled
90° turns vent Iouvered hoods
or elbows hoods
0 Rigid metal 64 ft (20 m) 58 ft (17.7 m)
Flexible metal 36 ft (11 m) 28 ft (8,5 m)
1 Rigid metal 54 ft (16.5 m) 48 ft (14.6 m)
Flexible metal 31 ft (9,4 m) 23 ft (7 m)
2 Rigid metal 44 ft (13,4 m) 38 ft (11,6 m)
Flexible metal 27 ft (8,2 m) 19 ft (5.8 m)
3 Rigid metal 35 ft (10.7 m) 29 ft (8.8 m)
Flexible metal 25 ft (7,6 m) 17 ft (5.2 m)
4 Rigid metal 27 ft (8,2 m) 21 ft (6.4 m)
Flexible metal 23 ft (7 m) 15 ft (4.6 m)
1=
2.
3.
Install exhaust hood. Use caulking compound to seal exterior
wall opening around exhaust hood.
Connect vent to exhaust hood. Vent must fit inside exhaust
hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.
Run vent to dryer location. Use the straightest path possible.
See "Determine vent path" in "Plan Vent System." Avoid 90°
turns. Use clamps to seal all joints. Do not use duct tape,
screws or other fastening devices that extend into the interior
of the vent to secure vent.
Excessive Weight Hazard
Use two or more people to move and install dryer.
Failure to do so can result in back or other injury.
1. To protect the floor, use a large flat piece of cardboard from
the dryer carton. Place cardboard under the entire back edge
of the dryer.
2. Firmly grasp the body of the dryer. Gently lay the dryer on the
cardboard. See illustration.
3. Examine the leveling legs. Find the diamond marking,
4. Screw the legs into the leg holes by hand. Use a wrench to
finish turning the legs until the diamond marking is no longer
visible.
5. Place a carton corner post from dryer packaging under each
of the 2 dryer back corners. Stand the dryer up. Slide the
dryer on the corner posts until it is close to its final location.
Leave enough room to connect the exhaust vent or gas line.
For mobile home use
Gas dryers must be securely fastened to the floor at the time of
installation.
Mobile home installations require a Mobile Home Installation Kit.
For more information, please reference the service numbers in
the "Assistance or Service" section of this manual.
1=
2.
Remove the red cap from the gas pipe.
Using a wrench to tighten, connect the gas supply to the
dryer. Use pipe-joint compound on the threads of all non-
flared male fittings. If flexible metal tubing is used, be sure
there are no kinks.
A .........
A. Flared male fitting
B. Non-flared male fitting
NOTE: For LP gas connections, you must use pipe-joint
compound resistant to the action of LP gas. Do not use
TEFLON _ttape.
19 TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.
12
3,
4.
A combination of pipe fittings must be used to connect the
dryer to the existing gas line. Shown is a recommended
connection. Your connection may be different, according to
the supply line type, size and location.
\
\
C
A. _" flexible gas connector
B. _" dryerpipe
C. _" to _" pipe elbow
D. _" pipe-to-flare adapter fitting
Open the shutoff valve in the supply line. The valve is open
when the handle is parallel to the gas pipe.
A. Closed valve
B.Open valve
Test all connections by brushing on an approved
noncorrosive leak-detection solution. Bubbles will show a
leak. Correct any leak found.
1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in
dryer. If connecting to existing vent, make sure the vent is
clean. The dryer vent must fit over the dryer exhaust outlet
and inside the exhaust hood. Check that the vent is secured
to exhaust hood with a 4" (10.2 cm) clamp.
2. Move dryer into its final location. Do not crush or kink vent.
3. (On gas models) Check that there are no kinks in the flexible
gas line.
4. Once the exhaust vent connection is made, remove the
corner posts and cardboard.
You can change your door swing from a right-side opening to a
left-side opening, if desired.
Remove the door
1. Open the dryer door. Remove the 4 screws that hold the door
hinge on the front panel of the dryer. Loosen, but do not
remove, the screw with the top keyhole opening last (second
from the top).
/
2,
3.
A. Dryer
B.Do not remove.
C. Dryer door
Lift and pull forward on the door so that the keyhole clears
the screw head. Remove the door.
Lay the dryer door on a flat, protected surface with the inside
door assembly facing up. Remove the last screw from Step 1.
Remove the 2 screws holding the handle to the door.
4.
Remove the 6 screws to release the outer door assembly
from the inner door assembly (see illustration). It is important
that you remove only the 6 indicated screws.
Check the levelness of the dryer. Check levelness first
side to side, then front to back.
If the dryer is not level, prop up the dryer using a wood block.
Use a wrench to adjust the legs up or down and check again for
levelness.
13
5. 3. Reassemble the inner and outer door assemblies with the
6 screws.
Lift the inner door assembly off of the outer door assembly.
Unsnap the handle from the outer door assembly, move it to
the other side, and snap in. Set the outer door assembly
aside.
Reverse the hinge and hinge bracket
1. Place the inner door, screw head side up, on the work
surface.
2. Remove the 4 screws that hold the hinge to the door.
4. Replace the 2 handle screws for the door handle of the door
assembly.
5. Remove the plug strip or label.
Style 1" Remove the plug strip.
Use a small flat-blade screwdriver to remove the plug
strip inthe door opening. Slide the head of the
screwdriver under the top portion of the plug strip, being
certain not to scratch the dryer surface. Lift up. Repeat in
the middle and at the bottom. Remove the plug strip in
the door opening and insert in the opposite side.
3. Remove the 2 screws that hold the handle bracket to the
door.
\
4. Move hinge to the other side and reattach with the 4 screws
removed in Step 2.
5. Move handle bracket to the other side and reattach with the
2 screws removed in Step 3.
6. Set the inner door assembly aside.
Reinstalling the door
1. Check for fingerprints on the glass. Clean if necessary.
2. Place the inner door assembly into the outer door assembly.
Align the hinge in the opening on the side. To fit correctly, the
inside door assembly edge is completely inside the outside
door assembly edge.
6.
Style 2: Remove the label.
Peel off the label located on the opposite side of the door
opening covering the hinge mounting holes. Apply the
label over the original hinge holes.
Insert a screw in the second opening from the top of the
hinge opening and partially tighten. Hang the door by placing
the top hinge keyhole over the second screw head and
tighten the screw. By putting this screw in first, the door will
hang in place while you insert and tighten the remaining
4 screws.
\
A. Dryer door
B. Dryer
C. Insert this screw first.
7. Close the door and check that it latches securely.
14
1. Check that all parts are now installed. If there is an extra part,
go back through the steps to see which step was skipped.
2. Check that you have all of your tools.
3. Check the dryer's final location. Be sure the vent is not
crushed or kinked.
4. Check that the dryer is level. See "Level Dryer."
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
8. Read "Dryer Use."
9. Wipe the dryer drum interior thoroughly with a damp cloth to
remove any dust.
10. Select a Timed Dry heated cycle, and start the dryer. Do not
select the Air Only Temperature setting.
If the dryer will not start, check the following:
Dryer is plugged into a grounded 3 prong outlet.
Electrical supply is connected.
Household fuse is intact and tight, or circuit breaker has
not tripped.
Dryer door is closed.
11. When the dryer has been running for 5 minutes, open the
dryer door and feel for heat. If you feel heat, cancel cycle and
close door. If you do not feel heat, turn off the dryer and
check that the gas supply line shutoff valve is open.
Ifthe gas supply line shutoff valve is closed, open it, then
repeat the 5-minute test as outlined above.
Ifthe gas supply line shutoff valve is open, contact a
qualified technician.
5. Plug into a grounded 3 prong outlet. Turn on power.
6. Remove any protective film or tape remaining on the dryer.
7. Dispose of/recycle all packaging materials.
15
DRYER USE
f
CONTROLON 0 AUTOMATIC MANUAL EstlmatedTime IO High
Heavy Duty% CYCLES /Timed Dry Rema n_ng Medium
Wet O Casu Rapid Dry Less Air Only Off
Dompo U or,
Euper 0
Cool Down O Delicate
Cycle Complete O _ O O O O
_MANUAL_ DRYNEES TEMP EXTRA CYCLE
Extra Care O DRY TIME LEVEL CARE END
SIGNAL
Control Locked O Hold for 3
seconds to
JocR / unlock Pause
control
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Do not dry anything that has ever had anything
flammable on it (even after washing).
Failure to follow these instructions can result in death,
explosion, or fire.
Fire Hazard
No washer can completely remove oil.
Do not dry anything that has ever had any type of oil on
it (including cooking oils).
Items containing foam, rubber, or plastic must be dried
on a clothesline or by using an Air Cycle.
Failure to follow these instructions can result in death
or fire.
This manual covers several different models. Your dryer may not
have all of the cycles and features described.
The following is a guide to starting your dryer. Please refer to
specific sections of this manual for more detailed information.
1. Clean lint screen before each load. See "Cleaning the Lint
Screen."
2. Place laundry in dryer and shut door.
3. Rotate the dial to select either an Automatic or Manual Cycle
then press the CONTROL ON button. The preset settings and
drying time for the cycle chosen will be displayed.
To use an Automatic Cycle
Point the dial to an Automatic Cycle.
Select DRYNESS LEVEL to adjust how dry you want the
load to be. The time displayed is an estimated length of
the cycle based on the Dryness Level selected. As the
cycle runs, the control senses the dryness of the load and
adjusts the time automatically for the selected Dryness
Level.
I ore
Less
O
DRYNESS
LEVEL
NOTE: Time is not adjustable for Automatic Cycles. Pressing
the Manual Dry Time (- or +) buttons will cause a triple beep,
indicating that the time cannot be changed.
Press the EXTRA CARE feature button if this option is
desi red.
Press the CYCLE END SIGNAL button to set signal
volume to desired level.
Press and hold HOLD TO START button until dryer starts
(about 1 second).
16
Once an Automatic Cycle has started, the Extra Care feature
and the Cycle End Signal level can be adjusted. Press the
OFF key twice to stop the dryer and clear the settings,
allowing you to select another cycle and Dryness Level.
How Automatic Cycles Work
This feature improves drying performance with Auto Moisture
Sensing Plus, which advances the cycle as moisture is
extracted from clothing. A thermistor (electronic temperature
sensor) and moisture sensing strips in the dryer drum help
measure the amount of moisture in the clothes as they
tumble. An electronic control determines the load type to help
save time, avoid overdrying, and increase the accuracy of the
end dryness level. After the first 5 minutes of an automatic
cycle, the estimated time display will adjust based on the
approximate load size, cycle, dryness level selected and
amount of moisture left in the clothes. When the clothes have
reached approximately 80% of the dryness level selected, the
estimated time display will adjust again, showing the final
drying time. Auto Moisture Sensing Plus takes the guesswork
out of drying time and enhances fabric care.
To use a Manual Cycle
Rotate the dial to select a Manual Cycle.
Press the MANUAL DRY TIME (- or +) buttons until the
desired drying time is displayed. Tap - or +, and the time will
change by 1-minute intervals. Press and hold - or +, and the
time will change by 5-minute intervals. The initial time
displayed is the actual drying time.
_MANUAL _)
DRY TIME
NOTE: The Manual Dry Time feature can be used only with
Manual Cycles.
Press TEMP until the desired temperature illuminates.
NOTE: Pressing the Dryness Level button will cause the triple
beep indicating that this option is not selectable. Also, a
Dryness Level is not indicated.
Press the EXTRA CARE feature button if this option is
desired.
Press the CYCLE END SIGNAL button to set volume to
desired level.
Press and hold HOLD TO START button until dryer starts
(about 1second).
While a Manual Cycle is running, you can change the settings
for Time, Temperature, the Extra Care feature, and the Cycle
End Signal. Press the OFF button twice to stop the dryer and
clear the settings, allowing you to select another cycle.
To stop your dryer at anytime
Press OFFtwice or open the door.
To pause the dryer at any time
Open the door or press OFF once.
To restart the dryer
Close the door and press and hold HOLD TO START button until
dryer starts.
NOTE: Drying will continue from where the cycle was interrupted
if you close the door and press Start within 5 minutes. Ifthe cycle
is interrupted for more than 5 minutes, the dryer will shut off.
Select new cycle settings before restarting the dryer.
This feature allows you to lock your settings to avoid unintended
use of the dryer. You can also use the Control Locked feature to
avoid unintended cycle or option changes during dryer operation.
To enable the Control Locked feature when dryer is
running:
Press and hold the CYCLE END SIGNAL button for 3 seconds.
The control is locked when a single beep is heard and the Control
Locked status light is on.
When the dryer is off, it is not necessary to press the Control
On button before activating the Control Locked feature.
To unlock:
Press and hold the CYCLE END SIGNAL button for 3 seconds to
turn this feature off.
NOTE: When the dryer is running and Control Locked is on, the
dryer can be stopped by pressing the Off button, but can't be
restarted until the control is unlocked.
.... t:;, ;,(; } s,;',r_
Select the correct cycle and dryness level or temperature for your
load. If an Automatic Cycle is running, the display shows the
estimated cycle time when your dryer is automatically sensing
the dryness level of your load. If a Manual Cycle is running, the
display shows the exact number of minutes remaining in the
cycle.
Cool Down tumbles the load without heat during the last few
minutes of all cycles. Cool Down makes the loads easier to
handle and reduces wrinkling. The length of the Cool Down
depends on the load size and dryness level.
Drying tips
Follow care label directions when they are available.
If desired, add a fabric softener sheet. Follow package
instructions.
Remove the load from the dryer as soon as tumbling stops to
reduce wrinkling. This is especially important for permanent
press, knits and synthetic fabrics.
Avoid drying heavy work clothes with lighter fabrics. This
could cause overdrying of lighter fabrics, leading to increased
shrinking or wrinkling.
Cycle tips
Dry most loads using the preset cycle settings.
Refer to the Automatic or Manual Preset Cycle Settings chart
(in the "Cycles" section) for a guide to drying various loads.
Drying temperature and Dryness Level are preset when
you choose an Automatic Cycle. You can choose a
different dryness level, depending on your load by
pressing the DRYNESS LEVEL button to select MORE or
LESS.
Ifyou wish to adjust the cycle length of a Manual Cycle,
you must press the MANUAL DRY TIME (- or +) buttons.
Adjust the temperature of a Manual Cycle by pressing
TEMP until the desired temperature is selected.
NOTE: You cannot choose a Dryness Level with Manual
Cycles.
17
You may follow the progress of your dryer with the drying status
indicator lights.
Sensing O
Wet O
Damp 0
Cool Down 0
CycleComplete 0
ExtraCare 0
Control Locked 0
Sensing
When a cycle is first turned on, the Sensing light illuminates until
a wet item is detected.
In an Automatic Cycle, if a wet item has not been detected
within 10 minutes, the Sensing light will turn off and the dryer
will shut down.
In a Manual Cycle, if a wet item is not detected after
10 minutes the Wet light turns on and the selected cycle
continues.
Wet
The Wet light will turn on when a wet item has been detected in
the dryer. The Wet light will remain on until:
The damp dry point is reached in an Automatic Cycle.
The dryer enters the cool down period in a Manual Cycle.
Damp
The Damp light indicates that the load has reached the damp dry
level.
NOTE: The Damp light is not used with Manual Cycles.
Cool Down
The Cool Down light illuminates during the cool down part of the
cycle. Laundry is cooling down for ease in handling.
Cycle Complete
The Cycle Complete light illuminates when a drying cycle is
finished. If the Extra Care feature has been selected, the Extra
Care feature indicator light will also be on.
The Cycle Complete light turns off 1 hour after the end of a drying
cycle (including the Extra Care cycle of 2 hours), when Off is
pressed, or when the door is opened.
Extra Care Feature
The Extra Care feature light illuminates when this option is
selected. This indicator stays on with the Cycle Complete light.
Control Locked
TheControl Locked light illuminates when this option is enabled.
Indicator lights
Other indicator lights on the control panel show Cycle,
Temperature and Cycle End Signal settings selected.
The time display will indicate the estimated or actual time
remaining in a cycle.
Select the drying cycle that matches the type of load you are
drying. See Automatic preset or Manual preset cycle settings
charts.
AUTOMATIC
Heavy Duty
NorrnaJ
Casual
Demicate
MANUAL
Timed Dry
Touchup
/' Rapid Dry
)
Cycle Control knob
Automatic Cycles
Automatic Cycles allow you to match the cycle to the load you
are drying. See the following Automatic preset cycle settings
chart. Each cycle dries certain fabrics at the recommended
temperature. A sensor detects the moisture in the load and
automatically adjusts the drying time for optimal drying.
Heavy Duty
Use this cycle to get High heat for heavyweight mixed loads,
cotton towels or jeans.
Normal
Use this cycle to get Medium heat for drying sturdy fabrics such
as work clothes and sheets.
Casual
Use this cycle to get Medium heat for drying no-iron fabrics such
as sport shirts, casual business clothes and permanent press
blends.
Delicate
Use this cycle to get Low heat for drying synthetic fabrics,
washable knit fabrics and no-iron finishes.
Super Delicate
Use this cycle to get Extra-Low heat to gently dry items such as
lingerie, exercise wear or sheer curtains.
18
Automatic preset cycle settings
Automatic Cycles Temp. Time*
Load Type (Minutes)
HEAVY DUTY High 40
Heavyweight mixed loads, towels,
jeans
NORMAL Medium 34
Corduroys, work clothes, sheets
CASUAL Medium 36
Permanent press, synthetics
DELICATE Low 28
Lingerie, blouses, washable
woolens
SUPER DELICATE Extra Low 22
Exercise wear, sheer curtains, lace
*Estimated Time with Dryness Level (medium) setting.
Manual Cycles
Use Manual Cycles to select a specific amount of drying time and
a drying temperature. When a Manual Cycle is selected, the
ESTIMATED TIME REMAINING display shows the actual time
remaining in your cycle. You can change the actual time in the
cycle by pressing the Manual Dry Time (- or +) buttons.
Timed Dry
Use this cycle to complete drying if items are still damp after an
Automatic Cycle. Timed Dry is also useful for drying heavyweight
and bulky items, such as bedspreads and work clothes.
Touchup
Use this setting to help smooth out wrinkles from such items as
clothes packed in a suitcase or items wrinkled from being left in
the dryer too long.
Rapid Dry
Use this cycle for drying small loads or loads that need a short
drying time.
Manual preset cycle settings
Manual Cycles Temp. Default Time
Load Type (Minutes)
TIMED DRY High 40
Heavyweight, bulky items,
bedspreads, work clothes
TOUCHUP Medium 20
Helps to smooth out
wrinkles
RAPID DRY High 27
Small loads
Addidosa m: s
Extra Care Feature
When you are unable to remove a load of clothes from the dryer
as soon as it stops, wrinkles can form. The Extra Care feature
periodically tumbles, rearranges and fluffs the load to help reduce
wrinkling.
Press the Extra Care feature to get up to 120 minutes of heat-
free, periodic tumbling at the end of a cycle.
Stop at any time by pressing the Extra Care feature or
opening the dryer door.
For the Casual Cycle, the Extra Care feature is preset to "On."
The other Automatic Cycles will retain the Extra Care feature
setting. (For example, if you select the Extra Care feature in
the Normal cycle, the Extra Care feature will be on the next
time you select the Normal cycle.)
NOTE: Ifyou do not select the Extra Care feature, the dryer stops
after the cool down period.
Temperature
Temperature settings are used with the Manual Cycles. Press
TEMP until the desired temperature setting illuminates.
Temperature settings cannot be used with the Automatic Cycles.
IOO High
cO Medium
Low
Extra Low
Air Only
O
TEMP
Air Only
Use the Air Only setting for items that require drying without heat
such as rubber, plastic and heat-sensitive fabrics. This chart
shows examples of items that can be dried using Air Only.
Type of Load Time*
(Minutes)
Foam rubber - pillows, padded bras, 20 - 30
stuffed toys
Plastic - Shower curtains, tablecloths 20 - 30
Rubber-backed rugs 40 - 50
Olefin, polypropylene, sheer nylon 10 - 20
*Reset time to complete drying, if needed.
When using Air Only
Check that coverings are securely stitched.
Shake and fluff pillows by hand periodically during the cycle.
Dry item completely. Foam rubber pillows are slow to dry.
NOTE: Automatic Cycles are not available when using the Air
Only setting.
19
Cycle End Signal
The Cycle End Signal produces an audible sound when the
drying cycle is finished. Promptly removing clothes at the end of
the cycle reduces wrinkling.
L°ud 1
Off
O
CYCLE
END
SIGNAL
Hold for 3
seconds to
Jack / unlock
control
Press and release the CYCLE END SIGNAL to adjust the sound
level or turn off the signal. Your dryer may vary from the model
shown and may not have the same feature as shown here.
NOTE: When the Extra Care feature is selected and the Cycle
End Signal is on, an audible sound will emit every 5 minutes until
the clothes are removed, or the Extra Care feature is finished.
The drying rack is useful for drying items you would not
necessarily want to tumble dry or that you would normally line dry
(for example, sweaters).
To use the drying rack
Do not remove the lint screen.
1. Open dryer door.
A. Front edge
2. Place drying rack inside dryer drum, positioning the back wire
on the ledge of the inner dryer back panel. Push down on
front edge of drying rack to secure over the lint screen.
3. Put the wet items on top of the rack. Leave space between
the items so air can reach all the surfaces.
NOTE: Do not allow items to hang over the edge of the rack.
°J/
4. Close the door.
5. Select a Manual cycle, and choose a temperature or Air Only
(see following chart). Items containing foam, rubber or plastic
must be dried on a clothesline or by using the Air Only
temperature setting.
6. You must select a time by pressing the MANUAL DRY TIME
(- or +) buttons. Reset time as needed to complete drying.
Refer to the following table.
7. Press (and hold) HOLD TO START button (about 1 second).
NOTE: You must remove rack for normal tumbling. Do not use
automatic cycles with the drying rack.
This chart shows examples of items that can be rack dried and
the suggested cycle, temperature setting and drying time. Actual
drying time will depend on the amount of moisture items hold.
Rack Dry Setting Temp. Time*
Wool Sweaters Timed Low 60
Block to shape and lay flat on Dry
the rack
Stuffed toys or pillows Timed Low 60
Cotton or polyester fiber filled Dry
Stuffed toys or pillows Timed Air Only 90
Foam rubber filled Dry (no heat)
Sneakers or canvas shoes Timed Air Only 90
Dry (no heat)
*(Minutes) Reset time to complete drying, if needed.
A
A. Dryer rack front edge
B. Dryer back panel
20
1 / 1

Maytag EPIC MGD9700S Mode d'emploi

Catégorie
Sèche-linge
Taper
Mode d'emploi