FEIN 7 129 22 61 09 0 Manuel utilisateur

FEIN Service

USA

FEIN Power Tools, Inc.

1000 Omega Drive

Suite 1180

Pittsburgh, PA 15205

Telephone: (412) 922-8886

Toll Free: 1-800-441-9878

www.feinus.com

Canada

FEIN Canadian Power Tool

Company

323 Traders Boulevard East

Mississauga, Ontario L4Z 2E5

Telephone.: (905) 8901390

Toll Free: 1-800-265-2581

FEIN Canadian Power Tool

Company

2810 De Miniac

St. Laurent, Quebec H4S 1K9

Telephone: (514) 331-7390

Toll Free: 1-800-789-8181

www.fein.com

Headquarter

C. & E. Fein GmbH

Hans-Fein-Straße 81

D-73529 Schwäbisch Gmünd-Bargau

www.fein.com

 AFMM18(QSL) 7 129 ...

✔

OBJ_DOKU-0000006440-001.fm Page 1 Tuesday, February 9, 2016 8:16 AM

2

Instruction Manual

Mode d’emploi

Instrucciones de uso

en

3

fr

20

es

38

OBJ_BUCH-0000000251-001.book Page 2 Monday, February 8, 2016 12:04 PM

3

en

For your safety.

Read all safety warnings and

all instructions. Failure to fol-

low the warnings and instructions may result

in electric shock, fire and/or serious injury.

Save all warnings and instructions for future-

reference.

Do not use this power tool before you

have thoroughly read and completely

understood this Instruction Manual, including

the figures, specifications, safety regulations

and the signs indicating DANGER, WARN-

ING and CAUTION.

Only carry out such operations with this

power tool as intended for by FEIN. Only use

application tools and accessories that have

been released by FEIN.

Please also observe the relevant national

industrial safety regulations.

Non-observance of the safety instructions in

the said documentation can lead to an electric

shock, burns and/or severe injuries.

This Instruction Manual should be kept for

later use and enclosed with the power tool,

should it be passed on or sold.

SAVE THESE INSTRUCTIONS.

The term “power tool” in the warnings refers

to your mains-operated (corded) power tool

or battery operated (cordless) power tool.

General safety rules.

1) Work area safety

a)Keep work area clean and well lit. Clut-

tered or dark areas invite accidents.

b)Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power

tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders away

while operating a power tool. Distrac-

tion can cause you to lose control.

2) Electrical safety

a)Power tool plugs must match the outlet.

Never modify the plug in any way. Do not

use any adapter plugs with earthed

(grounded) power tools. Unmodified

plugs and matching outlets will reduce

risk of electric shock.

b)Avoid body contact with earthed or

grounded surfaces such as pipes, radia-

tors, ranges and refrigerators. There is

an increased risk of electric shock if

your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power

tool will increase the risk of electric

shock.

d)Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

the power tool. Keep cord away from

heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase

the risk of electric shock.

e) When operating a power tool outdoors,

use an extension cord suitable for out-

door use. Use of a cord suitable for out-

door use reduces the risk of electric

shock.

f) If operating a power tool in a damp loca-

tion is unavoidable, use a ground fault

circuit interrupter (GFCI) protected sup-

ply. Use of an GFCI reduces the risk of

electric shock.

3) Personal safety

a)Stay alert, watch what you are doing

and use common sense when operating

a power tool. Do not use a power tool

while you are tired or under the influ-

ence of drugs, alcohol or medication. A

moment of inattention while operating

power tools may result in serious per-

sonal injury.

b)Use personal protective equipment.

Always wear eye protection. Protective

equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing pro-

tection used for appropriate conditions

will reduce personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the off-position before

connecting to power source and/or bat-

tery pack, picking up or carrying the

tool. Carrying power tools with your

finger on the switch or energising

power tools that have the switch on

invites accidents.

WARNING

OBJ_BUCH-0000000251-001.book Page 3 Monday, February 8, 2016 12:04 PM

4

en

d)Remove any adjusting key or wrench

before turning the power tool on. A

wrench or a key left attached to a rotat-

ing part of the power tool may result in

personal injury.

e) Do not overreach. Keep proper footing

and balance at all times. This enables

better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose cloth-

ing or jewelery. Keep your hair, clothing

and gloves away from moving parts.

Loose clothes, jewelry or long hair can

be caught in moving parts.

g)If devices are provided for the connec-

tion of dust extraction and collection

facilities, ensure these are connected

and properly used. Use of dust collec-

tion can reduce dust-related hazards.

4) Power tool use and care

a)Do not force the power tool. Use the cor-

rect power tool for your application. The

correct power tool will do the job bet-

ter and safer at the rate for which it was

designed.

b)Do not use the power tool if the switch

does not turn it on and off. Any power

tool that cannot be controlled with the

switch is dangerous and must be

repaired.

c) Disconnect the plug from the power

source and/or the battery pack from the

power tool before making any adjust-

ments, changing accessories, or storing

power tools. Such preventive safety

measures reduce the risk of starting the

power tool accidentally.

d)Store idle power tools out of the reach of

children and do not allow persons unfa-

miliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands

of untrained users.

e) Maintain power tools. Check for mis-

alignment or binding of moving parts,

breakage of parts and any other condi-

tion that may affect the power tool’s

operation. If damaged, have the power

tool repaired before use. Many accidents

are caused by poorly maintained power

tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with

sharp cutting edges are less likely to

bind and are easier to control.

g)Use the power tool, accessories and tool

bits etc. in accordance with these

instructions, taking into account the

working conditions and the work to be

performed. Use of the power tool for

operations different from those

intended could result in a hazardous sit-

uation.

5) Battery tool use and care

a)Recharge only with the charger speci-

fied by the manufacturer. A charger that

is suitable for one type of battery pack

may create a risk of fire when used with

another battery pack.

b)Use power tools only with specifically

designated battery packs. Use of any

other battery packs may create a risk of

injury and fire.

c) When battery pack is not in use, keep it

away from other metal objects, like

paper clips, coins, keys, nails, screws or

other small metal objects, that can

make a connection from one terminal to

another. Shorting the battery terminals

together may cause burns or a fire.

d)Under abusive conditions, liquid may be

ejected from the battery; avoid contact.

If contact accidentally occurs, flush

with water. If liquid contacts eyes, addi-

tionally seek medical help. Liquid

ejected from the battery may cause irri-

tation or burns.

6) Service

a)Have your power tool serviced by a qual-

ified repair person using only identical

replacement parts. This will ensure that

the safety of the power tool is main-

tained.

OBJ_BUCH-0000000251-001.book Page 4 Monday, February 8, 2016 12:04 PM

5

en

Special safety instructions.

Hold the power tool by the insulated gripping

surface when performing operations where

the application tool could contact hidden

wires. Contact with a “live” wire will also

make exposed metal parts of the power tool

“live” and shock the operator.

Use clamps or another practical method to

secure and support the work piece on a stable

surface. When holding the work piece only

by hand or against your body, it remains in an

unstable position, which can lead to loss of

control.

Do not use accessories which are not specifi-

cally designed and recommended by the

power tool manufacturer. Safe operation is

not ensured merely because an accessory fits

your power tool.

Grasp/hold the power tool in such a safe man-

ner that your body never comes in contact

with the application tool, particularly when

working with application tools pointing

toward the gripping area, such as with saw

blades or cutting tools. Touching sharp cut-

ting edges or edges can lead to injury.

Wear personal protective equipment. Depend-

ing on application, use face shield, safety

goggles or safety glasses. Where appropriate,

wear dust mask, hearing protectors, gloves

and workshop apron capable of stopping

small abrasive or workpiece fragments. The

safety glasses must be capable of protecting

against flying particles generated by the vari-

ous operations. Prolonged exposure to high

intensity noise may cause loss of hearing.

Do not direct the power tool against yourself,

other persons or animals. Danger of injury

from sharp or hot application tools.

Do not rivet or screw any name-plates or

signs onto the power tool. If the insulation is

damaged, protection against an electric shock

will be ineffective. Adhesive labels are recom-

mended.

Clean the ventilation openings on the power

tool at regular intervals using non-metal

tools. The blower of the motor draws dust

into the housing. An excessive accumulation

of metallic dust can cause an electrical hazard.

Use and handling of the battery

(battery pack)

To avoid hazardous situations such as burns,

fire, explosion, skin injuries, and other inju-

ries when handling the battery, observe the

following instructions:

Batteries must not be disassembled, opened

or reduced in size. Do not subject batteries to

mechanical impact or shock. Hazardous

vapours and fluid can escape in case of dam-

age and improper use of the battery. The

vapours can irritate the respiratory system.

Liquid ejected from the battery may cause

skin irritations or burns.

When battery fluid from a damaged battery

has come into contact with objects close by,

check the respective components, clean them

or replace them as required.

Keep the battery away from heat and fire. Do

not store the battery in direct sunlight.

Do not remove the battery from its original

packaging until it is going to be used.

Before any work on the machine itself,

remove the battery from the power tool. If the

power tool accidentally starts, there is danger

of injury.

Remove the battery only when the power tool

is switched off.

Keep the battery away from children.

Keep the battery clean and protect it against

moisture and water. Clean contaminated bat-

tery terminals and power tool connections

with a dry, clean cloth.

Use only intact original FEIN batteries that are

intended for your power tool. When working

with and charging incorrect, damaged,

repaired or reconditioned batteries, imita-

tions or other brands, there is danger of fire

and/or explosion.

Follow the safety warnings in the operating

instructions of the battery charger.

OBJ_BUCH-0000000251-001.book Page 5 Monday, February 8, 2016 12:04 PM

6

en

Handling hazardous dusts.

When working with power

tools, such as when grinding,

sanding, polishing, sawing or for other work

procedures where material is removed, dusts

develop that are both hazardous to one’s

health and can spontaneously combust or be

explosive.

Contact with or inhaling some dust types can

trigger allergic reactions to the operator or

bystanders and/or lead to respiratory infec-

tions, cancer, birth defects or other reproduc-

tive harm.

Examples of such materials which contain

chemicals that can produce hazardous dusts,

are:

– Asbestos and materials containing asbes-

tos;

– Lead-containing coatings, some wood

types such as beech and oak;

– Minerals and metal;

– Silicate particles from bricks, concrete and

other materials containing stone;

– Solvent from solvent-containing paint/

varnish;

– Arsenic, chromium and other wood pre-

servatives;

– Materials for pesticide treatment on boat

and ship hulls;

– Stainless steel dust, metal dust and non-

ferrous metal dust;

To minimize the unwanted intake of these

materials:

– Use dust extraction matched appropriately

for the developing dust.

– Use personal protective equipment, such

as a P2 filter-class dust protection mask.

– Provide for good ventilation of the work-

place.

The risk from inhaling dusts depends on how

often these materials are worked. Materials

containing asbestos may only be worked on

by specialists.

Wood and light-metal dust can

cause spontaneous combus-

tion or explosions.

Hot mixtures of sanding dust and paint/var-

nish remainders or other chemical materials

in the filter bag or the vac filter can self-ignite

under unfavorable conditions, such as spark-

ing from sanding metal, continuous sunlight

or high ambient temperatures. To prevent

this:

– Avoid overheating the material being

sanded and the power tool.

– Empty the dust collector/container in time.

– Observe the material manufacturer’s

working instructions.

– Observe the relevant regulations in your

country for the materials being worked.

Hand/arm vibrations.

While working with this power

tool, hand/arm vibrations

occur. These can lead to health impairments.

The vibration emission value

during actual use of the power

tool can differ from the declared value

depending on the ways in which the tool is

used.

It is necessary to identify

safety measures to protect the

operator that are based on an estimation of

exposure in the actual conditions of use.

The vibration emission level given in this

information sheet has been measured in

accordance with a standardised test given in

EN 60745 and may be used to compare one

tool with another. It may be used for a pre-

liminary assessment of exposure.

The declared vibration emission level repre-

sents the main applications of the tool. How-

ever if the tool is used for different

applications, with different accessories or

poorly maintained, the vibration emission

may differ. This may significantly increase the

exposure level over the total working period.

An estimation of the level of exposure to

vibration should also take into account the

times when the tool is switched off or when

it is running but not actually doing the job.

This may significantly reduce the exposure

level over the total working period.

Identify additional safety measures to protect

the operator from the effects of vibration

such as: maintain the tool and the accessories,

keep the hands warm, organisation of work

patterns.

WARNING

CAUTION

WARNING

OBJ_BUCH-0000000251-001.book Page 6 Monday, February 8, 2016 12:04 PM

7

en

Emission values for sound and vibration (Two-figure – specifications as per ISO 4871)

Sound emission AFMM18(QSL)

A-weighted emission pressure power level measured at the workplace

L

pA

(re 20 μPa), in decibels 74

Measuring uncertainty

K

pA

, in decibels 3

Measured A-weighted sound power level

L

wA

(re 1 pW), in decibels 85

Measuring uncertainty

K

wA

, in decibels 3

C-weighted peak sound pressure level measured at the workplace

L

pCpeak

,

in decibels 87

Measuring uncertainty

K

pCpeak

, in decibels 3

REMARK: The sum of the measured emission value and respective measuring inaccuracy

represents the upper limit of the values that can occur during measuring.

Wear hearing protection!

Measured values determined in accordance with the corresponding product standard.

Vibration

Classification of FEIN

application tools accord-

ing to vibration class

Weighted

acceleration*

VC0

< 2.5 m/s

2

< 8 ft/s

2

VC1

< 5 m/s

2

< 16 ft/s

2

VC2

< 7 m/s

2

< 23 ft/s

2

VC3

< 10 m/s

2

< 33 ft/s

2

VC4

< 15 m/s

2

< 50 ft/s

2

VC5

> 15 m/s

2

> 50 ft/s

2

K

a 1.5 m/s

2

4.92 ft/s

2

* These values are based on a work cycle consist-

ing of no-load and full-load operation of the same

duration.

For information on the vibration class assigned to

the application tool, please refer to the enclosed

data sheet 3 41 30 443 06 0.

OBJ_BUCH-0000000251-001.book Page 7 Monday, February 8, 2016 12:04 PM

8

en

Intended use of the power tool:

Hand-guided oscillator for sanding small sur-

faces, corners and edges, for sawing thin parts

of steel sheet, wood and plastic, for scraping,

polishing, rasping, cutting and separating with-

out water in weather-protected environ-

ments, using the application tools and

accessories recommended by FEIN.

Symbols.

Symbol, character Explanation

Observe the instructions in the text or graphic opposite!

General prohibition sign. This action is prohibited.

Make sure to read the enclosed documents such as the Instruction

Manual and the General Safety Instructions.

Do not touch the saw blade. Danger of sharp application tools moving

back and forth.

Warning against sharp edges of application tools, such as the cutting

edges of the cutter blades.

Before commencing this working step, remove the battery from the

power tool. Otherwise there may be danger of injury caused by

unintentional starting of the power tool.

Use eye protection during operation.

Wear hearing protection while working.

Use a dust mask during operation.

Use protective gloves during operation.

Do not charge damaged batteries.

Keep the battery away from fire. Protect the battery against heat, e. g.

against continuous intense sunlight.

Observe the notes in the text aside!

Confirms the conformity of the power tool with the guidelines of the

European Community.

This symbol confirms the certification of this product for the USA and

Canada.

OBJ_BUCH-0000000251-001.book Page 8 Monday, February 8, 2016 12:04 PM

9

en

This sign warns of a directly imminent, dangerous situation. A false

reaction can cause a severe or fatal injury.

This sign indicates a possible dangerous situation that could cause severe

or fatal injury.

This sign warns of a possible dangerous situation that could cause injury.

Recycling code: identifies recyclable materials

Worn out power tools and other electrotechnical and electrical

products should be sorted separately for environmentally-friendly

recycling.

Low oscillation rate

High oscillation rate

Maximal allowed oscillation rate

** may contain numbers and letters

Symbol, character Explanation

DANGER

WARNING

CAUTION

Character Unit of measurement,

national

Explanation

n

0

rpm; /min; min

-1

; r/min Rated oscillation rate

P

W Electrical power

° Oscillation angle

U V Electric voltage

f Hz Frequency

I

A Electric current intensity

m

lbs Mass

l ft, in Length, width, height, depth, diameter or thread

Ø ft, in Diameter of a round part

K...

Uncertainty

m/s

2

Vibrational emission value according to EN 60745

(vector sum of three directions)

m, s, kg, A, mm, V, W,

Hz, N, °C, dB, min, m/s

2

Basic and derived units of measurement from the

international system of units SI.

OBJ_BUCH-0000000251-001.book Page 9 Monday, February 8, 2016 12:04 PM

10

en

Technical description and specifications.

Before mounting or replacing application tools or accessories, remove the bat-

tery. This preventive safety measure rules out the danger of injuries through

accidental starting of the power tool.

All accessories described or shown in this instruction manual will not be included with your-

power tool.

WARNING

Thumbwheel for pre-selection

of oscillating frequency

Clamping lever

Application tool

On/Off switch

Battery

Gripping surface

Fig. 1

Battery-Unlocking button

OBJ_BUCH-0000000251-001.book Page 10 Monday, February 8, 2016 12:04 PM

11

en

Type AFMM18(QSL)

Order number 7 129 ...

Rated voltage 18 V

Rated oscillation rate 11000 – 18500 /min

Amplitude 2 x 1.7°

Weight according to EPTA-Procedure 01 2.9 lbs (1.3 kg)

Type B18A B18A

Battery type Lithium ion

(Li ion)

Lithium ion

(Li ion)

Rated voltage 18 V 18 V

Weight according to EPTA-Procedure 01

(Battery)

1.0 lbs (0.45 kg) 1.5 lbs (0.70 kg)

OBJ_BUCH-0000000251-001.book Page 11 Monday, February 8, 2016 12:04 PM

12

en

Assembly instructions.

Before mounting or replacing application tools or accessories, remove the bat-

tery. This preventive safety measure rules out the danger of injuries through

accidental starting of the power tool.

Removing and charging the battery

(figure 2).

Prior to the first charging procedure,

read the operating instructions of the

battery charger.

Charge the battery completely before

putting into operation for the first time.

Release the battery by pressing the battery

unlocking button and pull the battery out of

the handle. Do not exert any force when

doing this.

Connect the battery charger to a socket out-

let, slide the battery onto the battery charger

and charge the battery. After the charging

process is over, insert the battery into the

power tool and pull the plug of the battery

charger out of the socket outlet.

A new battery does not reach its full capacity

until after several charging and discharging

procedures.

Mounting the depth stop (figure 3).

Mount the depth stop with the 2 screws to

the bottom side of the gear case.

WARNING

2.

Fig. 2

Battery

Battery-Unlocking button

1.

2.

Fig. 3

Screws

Depth stop

OBJ_BUCH-0000000251-001.book Page 12 Monday, February 8, 2016 12:04 PM

13

en

Assembly instructions.

Before mounting or replacing application tools or accessories, remove the bat-

tery. This preventive safety measure rules out the danger of injuries through

accidental starting of the power tool.

For all work or when changing application tools, always wear protective gloves.

Danger of injury from the sharp edges of the application tools. Application tools

can become very hot while working. Danger of burns!

Changing the tool

Do not switch the power tool

on while the clamping lever is

open. Otherwise there is danger of crushes or

contusions to the hand and fingers.

Do not actuate the clamping

lever while the power tool is

running. Otherwise there is danger of injury.

Do not reach into the area of

the clamping jaws. Otherwise

there is danger of crushes or contusions to

the fingers.

Do not operate the power tool

with open clamping jaws and

without an application tool! This could dam-

age the power tool.

When the clamping jaws are

open before the application

tool is inserted, pivot the clamping lever

toward the front and then back again. The

clamping jaws are closed now. The application

tool can be inserted.

Inserting the application tool (figure 4).

Clean the tool holder and the application tool.

In the starting position, the clamping jaws in

the tool holder are together. In this position,

the application tool can be clipped-in easily.

WARNING

CAUTION

2.

3.

1.

Fig. 4

OBJ_BUCH-0000000251-001.book Page 13 Monday, February 8, 2016 12:04 PM

14

en

Positioning the tool (figure 5).

The application tool can be offset in 30° steps

and fastened in the most favorable working

position.

Ejecting the application tool (figure 6).

To eject the application tool and have the

starting position set, move the clamping lever

back to the stop; in this, the application tool

is also released.

Pay attention that the application tool is

seated straightly the tool holder.

For all work or when changing applica-

tion tools, always wear protective

gloves. Danger of injury from the sharp edges

of the application tools. Application tools can

become very hot while working. Danger of

burns!

3.

0°

30°

60°

90°

60°

30°

180°

4.

2.

1.

Fig. 5

180°

4.

2.

1.

4.

3.

Fig. 6

OBJ_BUCH-0000000251-001.book Page 14 Monday, February 8, 2016 12:04 PM

15

en

Working instructions.

Before mounting or replacing application tools or accessories, remove the bat-

tery. This preventive safety measure rules out the danger of injuries through

accidental starting of the power tool.

Do not use accessories not specifically intended and recommended for this power tool by FEIN.

The use of non-original FEIN accessories can lead to overheating of the power tool and destroy

it.

For each job, use only the FEIN application tool released and intended for the

respective application.

Switching on and off (figure 7).

Always hold the power tool

firmly. Otherwise, you could

lose control over the power tool.

The self-start prevention lock prevents the

power tool from automatically starting when

the battery is inserted while the on/off switch

is set to on.

Guide the power tool toward the work

piece only when switched on.

Switching on:

Push the switch toward the front (I).

Switching off:

Push the switch toward the rear ().

Setting the oscillating frequency

(figure 8).

Adjust the oscillating frequency infinitely vari-

able with the dial control.

Turn the dial control between “1” for the

lowest speed and “6” for the highest speed.

WARNING

CAUTION

Fig. 7

On/Off switch

1

2

3

4

5

6

Fig. 8

Thumbwheel for pre-selection

of oscillating frequency

OBJ_BUCH-0000000251-001.book Page 15 Monday, February 8, 2016 12:04 PM

16

en

Handling the battery.

Operate and charge the battery only within

the battery operating-temperature range of

0°C – 45°C (32°F –113°F). At the beginning

of the charging procedure, the battery tem-

perature must be within the battery operat-

ing-temperature range.

Battery charge-control indicator

(figure 9).

Press the button to activate the LED indica-

tion.

The real percentage of the battery charge

condition is only indicated when the power

tool motor is stopped.

The electronics automatically switch off the

motor prior to the battery being deep dis-

charged.

LED indi-

cator

Meaning Activity

1–4

green LED

Percentage

of charge

condition

Operation

Continu-

ous red

light

Battery is

almost

empty

Charge battery

Red flash-

ing light

Battery is

not ready

for opera-

tion

Bring the battery

into the battery

operating-temper-

ature range, then

charge

100 %

75 %

50 %

25 %

0 %

≤

=

Fig. 9

OBJ_BUCH-0000000251-001.book Page 16 Monday, February 8, 2016 12:04 PM

17

en

Notes on sanding.

Press the power tool with the sanding sheet

briefly and firmly against a flat surface and

briefly switch the power tool on. This pro-

vides for good adhesion and prevents prema-

ture wear.

When only one tip or corner of the sanding

sheet is worn, it can be removed again and

reattached, turned by 120°.

Work with the entire surface of the sanding

plate, not only with the tip.

When sanding with small triangle sanding

plates, select a high oscillating frequency

(electronics level 4 – 6); when sanding with

the round sanding plate and the large triangle

sanding plate, select a moderate oscillating

frequency (max. electronics level 4).

Sand with continuous motion applying mod-

erate pressure. Applying excessive pressure

does not increase the rate of removal, it only

wears off the sanding sheet faster.

Notes on sawing.

Select a high oscillating frequency. Round saw

blades can be released and clamped offset

again, to allow for uniform wearing off.

Notes on scraping.

Select a moderate to high oscillating fre-

quency.

OBJ_BUCH-0000000251-001.book Page 17 Monday, February 8, 2016 12:04 PM

18

en

Repair and customer service.

Before mounting or replacing application tools or accessories, remove the bat-

tery. This preventive safety measure rules out the danger of injuries through

accidental starting of the power tool.

Exchangeable parts

If required, you can change the following

parts yourself:

Application tools

Service.

Have maintenance carried out

only through qualified person-

nel. Incorrectly mounted leads and compo-

nents can cause serious injuries. Have the

required service carried out only through a

FEIN customer service agent.

The current spare parts list for this power

tool can be found in the Internet at

www.fein.com.

Cleaning.

Remove the battery prior to

any maintenance and clean-

ing. This preventive safety measure rules out

the danger of injuries through accidental start-

ing of the power tool.

When using in environments

with conductive dust in the

air, such as when working metals, this dust

can settle in the interior of the power tool.

Therefore, regularly blow out the interior of

the power tool from outside via the ventilation

openings with dry, oil-free compressed air;

always wear eye protection when doing this.

Do not attempt to clean

clogged or dirty ventilation

openings of the power tool with pointed

metal objects; use nonmetal tools or objects

if necessary.

Do not use cleaning agents

and solvents that can cause

damage to plastic parts. These include: Gas-

oline, carbon-tetrachloride, chloric solvents,

ammonia and domestic cleaning agents that

contain ammonia.

Warranty and liability.

The warranty for the product is valid in accordance with the legal regulations in the country

where it is marketed. In addition, FEIN also provides a guarantee in accordance with the FEIN

manufacturer’s warranty declaration.

All accessories described or shown in this instruction manual will not be included with your-

power tool.

Environmental protection, disposal.

Packaging, worn out power tools and accessories should be sorted for environmental-friendly

recycling.

Dispose of batteries only when discharged.

For batteries that are not completely discharged, insulate the terminals with tape as a protective

measure against short-circuiting.

For further information, please contact your specialist shop.

WARNING

CAUTION

OBJ_BUCH-0000000251-001.book Page 18 Monday, February 8, 2016 12:04 PM

19

en

Transport

The contained lithium-ion batteries are subject to the Dangerous Goods Legislation require-

ments. The user can transport the batteries by road without further requirements.

When being transported by third parties (e.g.: air transport or forwarding agency), special

requirements on packaging and labelling must be observed. For preparation of the item being

shipped, consulting an expert for hazardous material is required.

Dispatch batteries only when the housing is undamaged and no liquid is escaping from the bat-

tery. Make sure that the battery contacts are not short-circuited. Use the original packaging.

Pack up the battery in such a manner that it cannot move around in the packaging.

Please also observe possibly more detailed national regulations.

Provided accessories (figure 10).

Fig. 10

Battery charger

Battery

OBJ_BUCH-0000000251-001.book Page 19 Monday, February 8, 2016 12:04 PM

20

fr

Pour votre sécurité.

Lisez tous les avertisse-

ments de sécurité et

toutes les instructions. Ne pas suivre les aver-

tissements et instructions peut donner lieu à

une électrocution, un incendie et/ou une

blessure sérieuse.

Conservez tous les avertissements et toutes

les instructions pour pouvoir vous y reporter

ultérieurement.

Ne pas utiliser cet outil électrique avant

d’avoir soigneusement lu et parfaitement

compris cette notice d’utilisation y compris

les figures, les spécifications, les consignes de

sécurité ainsi que les indications marquées par

DANGER, AVERTISSEMENT et ATTEN-

TION.

N’utiliser cet outil électrique que pour les tra-

vaux pour lesquels il a été conçu par FEIN.

N’utiliser que des outils de travail et accessoi-

res autorisés par FEIN.

De même, respectez les dispositions concer-

nant la prévention des accidents du travail en

vigueur dans le pays en question.

Le non-respect des instructions de sécurité se

trouvant dans la documentation mentionnée

peut entraîner un choc électrique, un incendie

et/ou de graves blessures.

Bien garder cette notice d’utilisation en vue

d’une utilisation ultérieure ; elle doit être

jointe à l’appareil en cas de transmission ou de

vente à une tierce personne.

GARDER SOIGNEUSEMENT CES INSTRUC-

TIONS DE SECURITE.

Le terme « outil électrique » dans les consi-

gnes de sécurité fait référence à votre outil

électrique alimenté par le secteur (avec cor-

don d’alimentation) ou votre outil fonction-

nant sur batterie (sans cordon

d’alimentation).

Instructions générales de

sécurité.

1) Zone de travail

a)Conserver la zone de travail propre et

bien éclairée. Les zones en désordre ou

sombres sont propices aux accidents.

b)Ne pas faire fonctionner les outils élec-

trique en atmosphère explosive, par

exemple en présence de liquides inflam-

mables, de gaz ou de poussières. Les

outils électroportatifs produisent des

étincelles qui peuvent enflammer les

poussières ou les fumées.

c) Maintenir les enfants et les personnes

présentes à l’écart pendant l’utilisation

de l’outil. Les distractions peuvent vous

faire perdre le contrôle de l’outil.

2) Sécurité électrique

a)Il faut que les fiches de l’outil électrique

soient adaptées au socle. Ne jamais

modifier la fiche de quelque façon que

ce soit. Ne pas utiliser d’adaptateurs

avec des outils à branchement de terre.

Des fiches non modifiées et des socles

adaptés réduiront le risque de choc

électrique.

b)Eviter tout contact du corps avec des

surfaces reliées à la terre telles que les

tuyaux, les radiateurs, les cuisinières et

les réfrigérateurs. Il existe un risque

accru de choc électrique si votre corps

est relié à la terre.

c) Ne pas exposer les outils à la pluie ou à

des conditions humides. La pénétration

d’eau à l’intérieur d’un outil augmentera

le risque de choc électrique.

d)Ne pas maltraiter le cordon. Ne jamais

utiliser le cordon pour porter, tirer ou

débrancher l’outil. Maintenir le cordon à

l’écart de la chaleur, du lubrifiant, des

arêtes ou des parties en mouvement.

Des cordons endommagés ou emmêlés

augmentent le risque de choc électrique.

e) Lorsqu’on utilise un outil à l’extérieur,

utiliser un prolongateur adapté à l’utili-

sation extérieure. L’utilisation d’un cor-

don adapté à l’utilisation extérieure

réduit le risque de choc électrique.

f) Si l’usage d’un outil dans un emplace-

ment humide est inévitable, utilisez une

alimentation protégée par un dispositif

à courant différentiel résiduel (RCD).

L’usage d’un RCD réduit le risque de

choc électrique.

AVERTISSEMENT

OBJ_BUCH-0000000251-001.book Page 20 Monday, February 8, 2016 12:04 PM

La page charge ...

FEIN 7 129 22 61 09 0 Manuel utilisateur

Ce manuel convient également à

FEIN 7 129 22 61 09 0 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents