DeWalt DCE350M2 Mode d'emploi

Marque: DeWalt

Modèle: DCE350M2

Catégorie: Outils électroportatifs

Taper: Mode d'emploi

Ce manuel convient également à

DCE350M2w150b

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DeWALT

Instruction Manual

Guide D’utilisation

Manual de instrucciones

DCE350

20V Max* Cordless Dieless Cable Crimping Tool

Sertisseuse de câblage sans matrice et sans fil de 20V Max*

Herramienta de engaste de cables sin troquel inalámbrica de

20 V Máx*

Final Page Size: Half Letter (5.5 x 8.5”)

English (original instructions) 1

Français (traduction de la notice d’instructions originale) 14

Español (traducido de las instrucciones originales) 28

ENGLISH

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk

of personal injury or property damage.



DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or seriousinjury.



WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or seriousinjury.



CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderateinjury.



(Used without word) Indicates a safety related message.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in propertydamage.



WARNING! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

WARNING: To reduce the risk of injury, read the

instructionmanual.

Indenters

Latch

Latch pin

Shoulder strap ring

Reverse trigger switch

Trigger switch

Main handle

LED Worklight

Battery release button

Battery pack

Diagnostics panel

Power ON/OFF button

Micro USB port

Shoulder strap clip

FIG. A

English (original instructions)

ENGLISH

SAVE ALL WARNINGS AND

INSTRUCTIONS FOR FUTURE

REFERENCE

GENERAL POWER TOOL SAFETY WARNINGS

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

powertool.



WARNING! Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

Work Area Safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust orfumes.

c ) Keep children and bystanders away while

operating a power tool. Distractions can cause you

to losecontrol.

Electrical Safety

d ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will

reduce risk of electricshock.

e ) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed orgrounded.

f ) Do not expose power tools to rain or wet

conditions. Water entering a power tool will increase

the risk of electricshock.

g ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electricshock.

h ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electricshock.

i ) If operating a power tool in a damp location

is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of a GFCI

reduces the risk of electricshock.

Personal Safety

j ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools

may result in serious personalinjury.

k ) Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personalinjuries.

l ) Prevent unintentional starting. Ensure the

switch is in the off position before connecting to

power source and/or battery pack, picking up or

carrying the tool. Carrying power tools with your

finger on the switch or energizing power tools that

have the switch on invitesaccidents.

m ) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personalinjury.

n ) Do not overreach. Keep proper footing and

balance at all times. This enables better control of

the power tool in unexpectedsituations.

o ) Dress properly. Do not wear loose clothing or

jewelry. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewelry or

long hair can be caught in movingparts.

p ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used. Use of dust

collection can reduce dust-relatedhazards.

q ) Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles. A careless action can

cause severe injury within a fraction of a second.

Power Tool Use and Care

r ) Do not force the power tool. Use the correct

power tool for your application. The correct power

tool will do the job better and safer at the rate for

which it wasdesigned.

s ) Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must

berepaired.

t ) Disconnect the plug from the power source and/

or the battery pack from the power tool before

making any adjustments, changing accessories,

or storing power tools. Such preventive safety

measures reduce the risk of starting the power

toolaccidentally.

u ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands

of untrainedusers.

v ) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and

any other condition that may affect the power

tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are

caused by poorly maintained powertools.

ENGLISH

w ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier tocontrol.

x ) Use the power tool, accessories and tool bits, etc.

in accordance with these instructions, taking

into account the working conditions and the

work to be performed. Use of the power tool for

operations different from those intended could result

in a hazardoussituation.

y ) Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and

control of the tool in unexpected situations.

Battery Tool Use and Care

z ) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used

with another batterypack.

aa ) Use power tools only with specifically designated

battery packs. Use of any other battery packs may

create a risk of injury andfire.

ab ) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws, or other small metal objects,

that can make a connection from one terminal to

another. Shorting the battery terminals together may

cause burns or afire.

ac ) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation orburns.

ad ) Do not use a battery pack or tool that is

damaged or modified. Damaged or modified

batteries may exhibit unpredictable behaviour

resulting in fire, explosion or risk of injury.

ae ) Do not expose a battery pack or tool to fire

or excessive temperature. Exposure to fire or

temperature above 130 °C may cause explosion.

af ) Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range specified in the instructions.

Charging improperly or at temperatures outside the

specified range may damage the battery and increase

the risk of fire.

Service

ag ) Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power

tool ismaintained.

ah ) Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized service providers.

Additional Safety Rules for Crimping Tool



DANGER: Use only approved connectors and

cables in manufacturer-approved combinations

for successful installation. Combining materials

not approved by manufacturers can result in

faulty installations. Faulty installations can

result in catastrophic failures, injury to installers

and damage to property.



DANGER: To reduce the risk of serious injury,

turn off power to the electrical lines before

making a crimp. Failure to shut off power prior

to work could result in severe injury or death and

property damage.



WARNING: Use the crimping tool only for its

intended purpose. Other uses or modifying

the crimping tool for other applications may

damage the crimping tool, damage the indenters

and/or cause personal injury or create defective

connections.



WARNING: Though this

DeWALT

crimping tool

will reach the proper pressure to complete a

crimp successfully, connections can only be

effective when the connection is free from

defects and when the crimp is properly prepared

according to the connector manufacturer's

installation procedures. Proper preparation and

installation is the responsiblity of the installing

contractor.

• Keep all body parts away from the crimp head

during operation and any time the power is ON. A

moment of inattention while operating power tools,

may result in serious personal injury. Fingers or hands

can be crushed, fractured or amputated if they become

caught in the indenters or moving parts.

• Inspect tool and indenters before use. Never attempt

to repair a damaged crimp head or indenter.

Indenters that have been modified in any way can crack

during crimping resulting in serious injury. Replacement or

repair of crimp head may be required.

• This tool produces large forces that can break parts

and cause injury. Always be attentive and take proper

safety precautions, including wearing eye protection.

• Never run the tool with damaged indenters.

• Never crimp with the latch or latch pin open.

• Only trained personnel should operate this tool.

• Before operating, inspect the tool and LEDs on the

diagnostics panel. Correct any problems before using

the tool. Reference the Troubleshooting section for a list

of possible problems and solutions.

• Before operating the

DeWALT

DCE350 crimping

tool, read and understand all safety and operating

instructions including the connector manufacturer's

installation instructions and the instructions for

any other equipment used with this tool. Failure to

follow all instructions and warnings may result in

property damage and/or serious personal injury.

• Crush hazard. Keep the crimping area of the tool free

from hands and other objects while tool is in use.

Fingers could be crushed.

• Secure and support the material prior to making the

crimp to prevent movement during crimping.

ENGLISH

• Follow connector manufacturer's installation

instructions. Other uses may cause damage to the tool,

accessories, and workpiece.

• Keep a firm grip on the tool at all times. Forces on the

tool may change during and after the crimp.

• Always wear eye protection. Crimp operations may

cause material pieces to fly. Flying particles can cause

permanent eye damage.

• Always wear gloves when operating tool and

handling materials. The ends of the materials can be

sharp and can cause serious personal injury.

• Always wear safety shoes to protect your feet from sharp

metal debris on the floor.

Additional Safety Information



WARNING: ALWAYS use safety glasses. Everyday

eyeglasses are NOT safety glasses. Also use face or

dust mask if cutting operation is dusty. ALWAYS WEAR

CERTIFIED SAFETYEQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratoryprotection.



WARNING: Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to the State

of California to cause cancer, birth defects or

other reproductive harm. Some examples of these

chemicalsare:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-

treatedlumber.

Your risk from these exposures varies, depending on how

often you do this type of work. To reduce your exposure to

these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are

specially designed to filter out microscopicparticles.

• Avoid prolonged contact with dust from power

sanding, sawing, grinding, drilling, and other

construction activities. Wear protective clothing and

wash exposed areas with soap and water. Allowing

dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmfulchemicals.



WARNING: Use of this tool can generate and/

or disperse dust, which may cause serious and

permanent respiratory or other injury. Always use

NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles

away from face andbody.



WARNING: Always wear proper personal hearing

protection that conforms to ANSI S12.6 (S3.19)

during use. Under some conditions and duration

of use, noise from this product may contribute to

hearingloss.



CAUTION: When not in use, place tool on its side

on a stable surface where it will not cause a

tripping or falling hazard. Some tools with large

battery packs will stand upright on the battery pack

but may be easily knockedover.

• Air vents often cover moving parts and should be

avoided. Loose clothes, jewelry or long hair can be

caught in movingparts.

The label on your tool may include the following symbols. The

symbols and their definitions are asfollows:

V ......................... volts

Hz .......................hertz

min ..................... minutes

or DC ......direct current

...................... Class I Construction

(grounded)

…/min ..............per minute

BPM .................... beats per minute

IPM ..................... impacts per minute

RPM .................... revolutions per

minute

sfpm ................... surface feet per

minute

SPM .................... strokes per minute

A ......................... amperes

W ........................watts

or AC ...........alternating current

or AC/DC .... alternating or

direct current

...................... Class II

Construction

(double insulated)

........................ no load speed

n .........................rated speed

......................earthing terminal

.....................safety alert symbol

.....................visible radiation

..................... wear respiratory

protection

..................... wear eye

protection

..................... wear hearing

protection

..................... electric shock

hazard

.....................crush hazard

..................... read all

documentation

BATTERIES AND CHARGERS

The battery pack is not fully charged out of the carton.

Before using the battery pack and charger, read the

safety instructions below and then follow charging

proceduresoutlined. When ordering replacement battery

packs, be sure to include the catalog number andvoltage.

Your tool uses a

DeWALT

charger. Be sure to read all safety

instructions before using your charger. Consult the chart

at the end of this manual for compatibility of chargers and

batterypacks.

READ ALL INSTRUCTIONS

Important Safety Instructions for All

Battery Packs



WARNING: Read all safety warnings and all

instructions for the battery pack, charger and

power tool. Failure to follow the warnings and

instructions may result in electric shock, fire and/

or serious injury.

• Do not charge or use the battery pack in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Inserting or removing the battery

pack from the charger may ignite the dust orfumes.

• NEVER force the battery pack into the charger. DO

NOT modify the battery pack in any way to fit into

a non-compatible charger as battery pack may

rupture causing serious personal injury. Consult

ENGLISH

the chart at the end of this manual for compatibility of

batteries andchargers.

• Charge the battery packs only in designated

DeWALT

chargers.

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in

locations where the temperature may reach or

exceed 104°F (40°C) (such as outside sheds or metal

buildings in summer). For best life store battery packs in

a cool, drylocation.

NOTE: Do not store the battery packs in a tool with

the trigger switch locked on. Never tape the trigger

switch in the ONposition.

• Do not incinerate the battery pack even if it is

severely damaged or is completely worn out. The

battery pack can explode in a fire. Toxic fumes and

materials are created when lithium ion battery packs

areburned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open

eye for 15 minutes or until irritation ceases. If medical

attention is needed, the battery electrolyte is composed of

a mixture of liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause

respiratory irritation. Provide fresh air. If symptoms

persist, seek medicalattention.



WARNING: Burn hazard. Battery liquid may be

flammable if exposed to spark orflame.



WARNING: Fire hazard. Never attempt to open the

battery pack for any reason. If the battery pack case

is cracked or damaged, do not insert into the charger.

Do not crush, drop or damage the battery pack. Do

not use a battery pack or charger that has received a

sharp blow, been dropped, run over or damaged in

any way (e.g., pierced with a nail, hit with a hammer,

stepped on). Damaged battery packs should be

returned to the service center forrecycling.

Transportation



WARNING: Fire hazard. Do not store or carry the

battery pack so that metal objects can contact

exposed battery terminals. For example, do

not place the battery pack in aprons, pockets, tool

boxes, product kit boxes, drawers, etc., with loose

nails, screws, keys, etc. Transporting batteries

can possibly cause fires if the battery terminals

inadvertently come in contact with conductive

materials such as keys, coins, hand tools and the

like. The US Department of Transportation Hazardous

Material Regulations (HMR) actually prohibit

transporting batteries in commerce or on airplanes in

carry-on baggage UNLESS they are properly protected

from short circuits. So when transporting individual

battery packs, make sure that the battery terminals

are protected and well insulated from materials that

could contact them and cause a short circuit.

Shipping the

DeWALT

FLEXVOLT™ Battery

The D

WALT FLEXVOLT™ battery has two modes: Use and

Shipping.

Use Mode: When the FLEXVOLT™ battery stands alone or is

in a D

WALT 20V Max* product, it will operate as a 20V Max*

battery. When the FLEXVOLT™ battery is in a 60V Max* or a

120V Max* (two 60V Max* batteries) product, it will operate

as a 60V Max* battery.

Shipping Mode: When

the cap is attached to

the FLEXVOLT™ battery,

the battery is in Shipping

Mode. Strings of cells are

electrically disconnected within the pack resulting in three

batteries with a lower Watt hour (Wh) rating as compared

to one battery with a higher Watt hour rating. This increased

quantity of three batteries with the lower Watt hour rating

can exempt the pack from certain shipping regulations that

are imposed upon the higher Watt hour batteries.

The battery label indicates two Watt hour ratings (see

example). Depending on how the battery is shipped, the

appropriate Watt hour rating must be used to determine

the applicable shipping requirements. If utilizing the

shipping cap, the pack will be considered 3 batteries at

the Watt hour rating indicated for “Shipping”. If shipping

without the cap or in a tool, the pack will be considered one

battery at the Watt hour rating indicated next to “Use”.

USE: 120 Wh Shipping: 3 x 40 Wh

Example of Use and Shipping Label Marking

Shipping Watt hour rating indicates 3 x 40 Wh, meaning 3

batteries of 40 Watt hours each. The Use Watt hour rating

indicates 120 Watt hour (1 battery implied).

Fuel Gauge Battery Packs (Fig. B)

Some

DeWALT

battery packs include a fuel gauge which

consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

The fuel gauge is an indication of approximate levels of

charge remaining in the battery pack according to the

followingindicators:

75–100% charged

51–74% charged

< 50% charged

Pack needs to be charged

To actuate the fuel gauge, press and hold the fuel gauge

button. A combination of the three green LED lights will

illuminate designating the level of charge left. When the

level of charge in the battery is below the usable limit, the

fuel gauge will not illuminate and the battery will need to

berecharged.

ENGLISH

FIG. B

NOTE: The fuel gauge is only an indication of the charge left

on the battery pack. It does not indicate tool functionality

and is subject to variation based on product components,

temperature and end-userapplication.

For more information regarding fuel gauge battery packs,

please contact call 1-800-4-

DeWALT

(1-800-433-9258) or

visit our website www.dewalt.com.

The RBRC® Seal

The RBRC® (Rechargeable Battery

Recycling Corporation) Seal on the nickel

cadmium, nickel metal hydride or lithium-

ion batteries (or battery packs) indicates

that the costs to recycle these batteries

(or battery packs) at the end of their useful life have already

been paid by

DeWALT

. In some areas, it is illegal to place

spent nickel cadmium, nickel metal hydride or lithium-ion

batteries in the trash or municipal solid waste stream and

the Call2Recycle® program provides an environmentally

consciousalternative.

Call 2 Recycle, Inc., in cooperation with

DeWALT

and other

battery users, has established the program in the United

States and Canada to facilitate the collection of spent nickel

cadmium, nickel metal hydride or lithium-ion batteries. Help

protect our environment and conserve natural resources by

returning the spent nickel cadmium, nickel metal hydride

or lithium-ion batteries to an authorized

DeWALT

service

center or to your local retailer for recycling. You may also

contact your local recycling center for information on

where to drop off the spent battery. RBRC® is a registered

trademark of Call 2 Recycle,Inc.

RBRC™ is a registered trademark of the Rechargeable Battery

RecyclingCorporation.

Important Safety Instructions for All

Battery Chargers



WARNING: Read all safety warnings and all

instructions for the battery pack, charger and

power tool. Failure to follow the warnings and

instructions may result in electric shock, fire and/

or serious injury.

• DO NOT attempt to charge the battery pack with

any chargers other than the ones in this manual.

The charger and battery pack are specifically designed to

worktogether.

• These chargers are not intended for any uses other

than charging

DeWALT

rechargeable batteries.

Any other uses may result in risk of fire, electric shock

orelectrocution.

• Do not expose the charger to rain orsnow.

• Pull by the plug rather than the cord when

disconnecting the charger. This will reduce the risk of

damage to the electric plug andcord.

• Make sure that the cord is located so that it will not

be stepped on, tripped over or otherwise subjected

to damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in

risk of fire, electric shock orelectrocution.

• When operating a charger outdoors, always provide

a dry location and use an extension cord suitable

for outdoor use. Use of a cord suitable for outdoor use

reduces the risk of electricshock.

• An extension cord must have adequate wire size

(AWG or American Wire Gauge) for safety. The smaller

the gauge number of the wire, the greater the capacity

of the cable, that is, 16 gauge has more capacity than 18

gauge. An undersized cord will cause a drop in line voltage

resulting in loss of power and overheating. When using

more than one extension to make up the total length,

be sure each individual extension contains at least the

minimum wire size. The following table shows the correct

size to use depending on cord length and nameplate

ampere rating. If in doubt, use the next heavier gauge. The

lower the gauge number, the heavier thecord.

Minimum Gauge for Cord Sets

Volts

Total Length of Cord in Feet

(meters)

120 V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240 V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Ampere Rating

American Wire Gauge

Than

Not

Than

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of the charger or

place the charger on a soft surface that might block

the ventilation slots and result in excessive internal

heat. Place the charger in a position away from any heat

source. The charger is ventilated through slots in the top

and the bottom of thehousing.

• Do not operate the charger with a damaged cord

orplug.

• Do not operate the charger if it has received a sharp

blow, been dropped or otherwise damaged in any

way. Take it to an authorized servicecenter.

• Do not disassemble the charger; take it to an

authorized service center when service or repair

is required. Incorrect reassembly may result in a risk of

electric shock, electrocution orfire.

• Disconnect the charger from the outlet before

attempting any cleaning. This will reduce the risk of

electric shock. Removing the battery pack will not reduce

thisrisk.

• NEVER attempt to connect 2 chargerstogether.

• The charger is designed to operate on standard

120V household electrical power. Do not attempt to

ENGLISH

use it on any other voltage. This does not apply to the

vehicularcharger.



WARNING: Shock hazard. Do not allow any liquid to

get inside the charger. Electric shock mayresult.



WARNING: Burn hazard. Do not submerge the

battery pack in any liquid or allow any liquid to

enter the battery pack. Never attempt to open the

battery pack for any reason. If the plastic housing of

the battery pack breaks or cracks, return to a service

center for recycling.



CAUTION: Burn hazard. To reduce the risk of injury,

charge only

DeWALT

rechargeable battery packs.

Other types of batteries may overheat and burst

resulting in personal injury and propertydamage.

NOTICE: Under certain conditions, with the charger

plugged into the power supply, the charger can

be shorted by foreign material. Foreign materials

of a conductive nature, such as, but not limited to,

grinding dust, metal chips, steel wool, aluminum

foil or any buildup of metallic particles should be

kept away from the charger cavities. Always unplug

the charger from the power supply when there is no

battery pack in the cavity. Unplug the charger before

attempting toclean.

Charging a Battery (Fig. C)

1. Plug the charger into an appropriate outlet before

inserting battery pack.

Fig. C

2. Insert the battery pack

9

into the charger, making sure

the battery pack is fully seated in the charger. The red

(charging) light will blink continuously indicating that

the charging process has started.

3. The completion of charge will be indicated by the red

light remaining ON continuously. The battery pack is

fully charged and may be used at this time or left in the

charger. To remove the battery pack from the charger,

push the battery release button

8

on the battery pack.

NOTE: To ensure maximum performance and life of lithium-

ion battery packs, charge the battery pack fully before first

use.

Charger Operation

Refer to the indicators below for the charge status of the

battery pack.

DCB101

Charging

Fully Charged

Hot/Cold Pack Delay

Problem Pack or Charger

DCB107, DCB112, DCB113, DCB115, DCB118, DCB132

Charging

Fully Charged

Hot/Cold Pack Delay*

* DCB107, DCB112, DCB113, DCB115, DCB118, DCB132:

The red light will continue to blink, but a yellow indicator

light will be illuminated during this operation. Once the

battery pack has reached an appropriate temperature, the

yellow light will turn off and the charger will resume the

charging procedure.

The compatible charger(s) will not charge a faulty battery

pack. The charger will indicate faulty battery pack by

refusing to light or by displaying a problem pack or charger

blink pattern.

NOTE: This could also mean a problem with a charger.

If the charger indicates a problem, take the charger and

battery pack to be tested at an authorized service center.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot

or too cold, it automatically starts a Hot/Cold Pack Delay,

suspending charging until the battery pack has reached an

appropriate temperature. The charger then automatically

switches to the pack charging mode. This feature ensures

maximum battery pack life.

A cold battery pack will charge at a slower rate than a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery pack warms.

The DCB118 charger is equipped with an internal fan

designed to cool the battery pack. The fan will turn on

automatically when the battery pack needs to be cooled.

Never operate the charger if the fan does not operate

properly or if ventilation slots are blocked. Do not permit

foreign objects to enter the interior of the charger.

Electronic Protection System

Li-Ion tools are designed with an Electronic Protection

System that will protect the battery pack against

overloading, overheating or deep discharge.

The tool will automatically turn off if the Electronic

Protection System engages. If this occurs, place the lithium-

ion battery pack on the charger until it is fully charged.

Wall Mounting

DCB107, DCB112, DCB113, DCB115, DCB118, DCB132

These chargers are designed to be wall mountable or to

sit upright on a table or work surface. If wall mounting,

locate the charger within reach of an electrical outlet,

ENGLISH

and away from a corner or other obstructions which may

impede air flow. Use the back of the charger as a template

for the location of the mounting screws on the wall. Mount

the charger securely using drywall screws (purchased

separately) at least 1" (25.4 mm) long, with a screw head

diameter of 0.28–0.35" (7–9mm), screwed into wood to an

optimal depth leaving approximately 7/32" (5.5 mm) of the

screw exposed. Align the slots on the back of the charger

with the exposed screws and fully engage them in the slots.

Charger Cleaning Instructions



WARNING: Shock hazard. Disconnect the charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using

a cloth or soft non-metallic brush. Do not use water or

any cleaning solutions.

Important Charging Notes

1. Longest life and best performance can be obtained if

the battery pack is charged when the air temperature is

between 65°F and 75°F (18° – 24°C). DO NOT charge

the battery pack in an air temperature below +40°F

(+4.5°C), or above +104°F (+40°C). This is important

and will prevent serious damage to the battery pack.

2. The charger and battery pack may become warm to the

touch while charging. This is a normal condition, and

does not indicate a problem. To facilitate the cooling of

the battery pack after use, avoid placing the charger or

battery pack in a warm environment such as in a metal

shed or an uninsulated trailer.

3. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp

or other appliance;

b. Check to see if receptacle is connected to a light

switch which turns power off when you turn out the

lights;

c. Move the charger and battery pack to a location

where the surrounding air temperature is

approximately 65°F – 75°F (18° – 24°C);

d. If charging problems persist, take the tool, battery

pack and charger to your local service center.

4. The battery pack should be recharged when it fails to

produce sufficient power on jobs which were easily

done previously. DO NOT CONTINUE to use under these

conditions. Follow the charging procedure. You may

also charge a partially used pack whenever you desire

with no adverse effect on the battery pack.

5. Foreign materials of a conductive nature such as, but

not limited to, grinding dust, metal chips, steel wool,

aluminum foil, or any buildup of metallic particles

should be kept away from charger cavities. Always

unplug the charger from the power supply when there

is no battery pack in the cavity. Unplug the charger

before attempting to clean.

6. Do not freeze or immerse the charger in water or any

other liquid.

Storage Recommendations

1. The best storage place is one that is cool and dry, away

from direct sunlight and excess heat or cold.

2. For long storage, it is recommended to store a fully

charged battery pack in a cool dry place out of the

charger for optimal results.

NOTE: Battery packs should not be stored completely

depleted of charge. The battery pack will need to be

recharged before use.

SAVE THESE INSTRUCTIONS FOR

FUTURE USE

COMPONENTS (FIG. A)



WARNING: Never modify the power tool or any part

of it. Damage or personal injury couldresult.

Refer to Figure A at the beginning of this manual for a

complete list ofcomponents.

INTENDED USE

This cordless dieless crimping tool is designed for

professional crimping of specific electrical applications only.

Only trained personnel should operate this tool.

DO NOT use under wet conditions or in presence of

flammable liquids orgases.

This crimping tool is a professional power tool. DO NOT

let children come into contact with the tool. Supervision is

required when inexperienced operators use thistool.

Introduction

The DCE350 Cordless Dieless Crimping Tool uses an electric

motor to power a hydraulic piston pump. The pumping

action forces a ram forward that forces closed a set of

indenters. The DCE350 is designed to mechanically crimp

connectors onto cables to create a tight and permanent

connection.

Trigger Switch (Fig. A)

Squeezing the trigger switch

6

advances the indenters,

while fully releasing the trigger switch stops the advance of

the indenters.

Reverse Trigger Switch (Fig. A)

Squeezing the reverse trigger switch

5

retracts the

indenters which releases the crimping action.

Shoulder Strap (Fig. A)



WARNING: The shoulder strap and ring are intended

for transporting the tool. They are not intended for

tethering or securing the tool to a person or object

during use.



WARNING: Do not transport the tool with the main

power ON. Switch the main power OFF prior to

transporting.

Your crimping tool comes with a shoulder strap. Hook the

shoulder strap clips

14

into the shoulder strap ring

4

LED Worklight (Fig. A)

The LED worklight

8

is located on the foot of the tool. The

worklight is activated when the trigger switch is depressed.

It will remain on for 2minutes. After 1 minute, 40 seconds,

ENGLISH

the light will dim to 25% indicating that the light is going

to turn off.

LED Display (Fig. D)

The LED display on the top of the crimping tool includes

the power ON/OFF button

12

maintenance LED

15

, cycle

complete LED

16

, battery state of charge LED

17

, and

temperature LEDs

18

. Refer to the LED Indications chart

for specific information.

FIG. D

When the battery state of charge LED

17

is lit, regardless of

color, the tool is ON.

DeWALT

CRIMP CONNECT™ System

This crimping tool is capable of connecting with a computer

via the micro USB port

13

on the back of the tool using the

micro USB cable included with your tool. This allows the

user to connect the

DeWALT

crimping tool to a computer

which utilizes

DeWALT

's CRIMP CONNECT

System

software.

NOTE: The CRIMP CONNECT™ System software is governed

by separate terms and conditions available for viewing

through the software download.

Step 1: Download the CRIMP CONNECT™ System software

to your computer at www.dewalt.com/crimpconnect.

Step 2: Follow the instructions in the software to create

your CRIMP CONNECT™ System account.

Step 3: Connect your crimping tool with the

DeWALT

CRIMP CONNECT™ System software by first connecting the

provided micro USB cable to the micro USB port

13

on the

back of the tool to a USB port on a computer. Then go to

the Home screen of the program to access tool tracking and

usage reports stored on the crimping tool.

NOTE: The USB connection will not charge the tool's battery

pack.

For more information on

DeWALT

CRIMP CONNECT™ System

functionality and features, please call 1–800–4-

DeWALT

(1–800–433–9258), visit www.

DeWALT

.com or view the FAQ

page and help screens located inside the software.

OPERATION



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.



WARNING: Inspect the indenters and connectors

before use. Only use properly matched

connectors and cable.

Installing and Removing the Battery Pack

(Fig. E)

NOTE: For best results, make sure your battery pack is

fullycharged.

To install the battery pack into the tool handle, align the

battery pack with the rails inside the tool’s handle and slide

it into the handle until the battery pack is firmly seated in

the tool and ensure that it does notdisengage.

To remove the battery pack from the tool, press the release

button and firmly pull the battery pack out of the tool

handle. Insert it into the charger as described in the charger

section of thismanual.

FIG. E

Proper Hand Position (Fig. F)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position as shown.



WARNING: To reduce the risk of serious personal injury,

ALWAYS hold securely in anticipation of a sudden

reaction.

Proper hand position requires one hand on the main handle

7

as shown.

FIG. F



WARNING: CUT OR AMPUTATION HAZARD. Never

have any part of your body near the crimp head or

moving parts during the crimp cycle, or whenever the

main power is ON. Serious personal injury may occur.



WARNING: Proper material preparation and

installation is the responsibility of the installing

contractor.



WARNING: The crimp connectors must be used

in compliance with applicable building codes

and as approved by the authorities having

jurisdiction. For proper installation procedures and

to reduce the risk the risk of failure resulting in injury

or property damage, follow all published safety and

installation instructions.

ENGLISH

Preparing the Connection



WARNING: Always follow the specific

manufacturer's installation instructions for

connector and cable combinations being

used. It is the installer's responsibility to ensure the

compatibility of the cable and connectors used for the

crimp. Failure to follow all instructions and warnings

may result in property damage and/or serious personal

injury.

1. Before operating, make sure that the work area and the

area below are clear of people and other distractions

and that the tool and work area have been properly

set up.

2. Prepare the connectors and cable according to the

manufacturer’s specifications.

3. Make sure the cable is inserted to the proper depth

in the connector in accordance with the connector

manufacturer's specifications.

Crimping



WARNING: An incomplete crimp can cause property

damage.

• Always use the manufacturer-approved

combination of connector and cable. Failure

to do so, may result in an incomplete or faulty

connection.



WARNING: To reduce the risk of serious personal

injury, inspect the crimp head assembly for cleanliness,

cracks or other damage before beginning a crimp.

Using a dirty or damaged crimp head assembly could

result in improper crimp connections that could lead

to extensive property damage. Return damaged crimp

head assembly to a

DeWALT

service facility.



WARNING: To reduce the risk of serious personal

injury, prior to use, inspect workpieces for cracks,

defects or wear. Defective workpieces may shatter.



WARNING: Before turning on the crimping tool,

be sure hands are clear of the crimp head.

Before beginning a crimp, check the battery pack fuel gauge

to determine whether the battery charge is sufficient to

complete the crimping operation.

NOTE: The tool will turn off automatically after 2 minutes

of no use.

Always follow the specific manufacturer's installation

instructions for the appropriate length to strip the cable and

preparation of the workpiece surface.

1. Insert the entire stripped part of the cable into the

connector.

2. If necessary, pull open the latch pin

3

to rotate the

latch

2

open. This will allow more room to fit the

connector inside the crimp head when crimping in

tight spaces. Rotate the latch closed then slide the latch

3

closed until the ball detent snaps into the pin.

This locks the latch pin into place. Align the connector

midway between the indenters

1

. Never crimp with the

latch or latch pin open.

3. Turn the tool ON by holding the power ON/OFF button

12

until all 3 LEDs illuminate green.

4. Press and hold the trigger switch until the cycle is

complete, indicated by the indenters automatically

returning to their original position. The LED worklight

will illuminate the workpiece when the trigger is pulled.

5. When the cycle is complete, the Cycle Complete LED

16

will flash green for 5 seconds. If the crimp cycle is

incomplete, the cycle complete LED

16

will flash red

for 5 seconds. No action is possible until the user presses

the ON/OFF button.

6. Repeat steps 4 and 5 according to the connector

manufacturer’s instructions. Crimp sequences start at

the pad for lugs and the center for splices and work

toward the cable.

7. Complete the number of crimps specified by the

manufacturer.

NOTE: If the battery dies or tool malfunctions during the

cycle, the indenters can retract by pressing the reverse

trigger switch

5

. Hold tool securely until the indenters

retract fully.

NOTE: Clean off oxide inhibitor from the aluminum

connectors after completion.

NOTE: If the tool does not complete the crimp properly,

read the Troubleshooting section or take the tool to a local

dealer or authorized service center.

NOTE: When crimping overhead, always confirm workpiece

and tool are secure before crimping.

MAINTENANCE



WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start-up can causeinjury.



WARNING: Before each use, inspect the tool

(including LED indicators) and correct any

problems before attempting to use.



WARNING: Skin injection hazard. The oil in the

mechanism is under extreme pressure. Do not

use hands to check for oil leaks.



WARNING: Explosion hazard. The internal

hydraulic system creates extreme pressures. Only

DeWALT

-qualified personnel should service this

tool.

Required Maintenance

Maintenance is required when the crimping tool reaches

25,000 cycles. Warning indicators will illuminate on the

diagnostic panel

11

as follows.

1. Maintenance warning at 24,500 cycles (Maintenance

LED lights yellow continuously)

2. Final maintenance warning at 24,900 cycles

(Maintenance LED flashes yellow continuously)

3. Needs service at 25,000 cycles (Maintenance LED lights

red for 10 seconds then turns tool off automatically).

At 25,000 cycles, the tool will no longer run. Take your

ENGLISH

tool to a local dealer or authorized service center for

maintenance and recalibration.

Cleaning



WARNING: Blow dirt and dust out of all air vents with

clean, dry air at least once a week. To minimize the risk

of eye injury, always wear ANSI Z87.1 approved eye

protection when performingthis.



WARNING: Never use solvents or other harsh

chemicals for cleaning the non-metallic parts of

the tool. These chemicals may weaken the plastic

materials used in these parts. Use a cloth dampened

only with water and mild soap. Never let any liquid

get inside the tool; never immerse any part of the tool

into aliquid.

Regularly clean the indenters to be sure they are free of dirt

and debris to ensure a proper crimp.

Accessories



WARNING: Since accessories, other than those offered

or recommended by

DeWALT

, have not been tested

with this product, use of such accessories with this tool

could be hazardous. To reduce the risk of injury, only

DeWALT

recommended accessories should be used

with thisproduct.

Recommended accessories for use with your tool

are available at extra cost from your local dealer or

authorized service center. If you need assistance in

locating any accessory, please contact

DeWALT

Industrial

Tool Co., 701East Joppa Road, Towson, MD 21286, call

1-800-4-

DeWALT

(1-800-433-9258) or visit our website:

www.dewalt.com.

Repairs

The charger and battery pack are notserviceable.



WARNING: To assure product SAFETY and

RELIABILITY, repairs, maintenance and adjustment

(including brush inspection and replacement) should

be performed by a

DeWALT

factory service center

or a

DeWALT

authorized service center. Always use

identical replacementparts.

Thank you for your purchase. Register your product nowfor:

• WARRANTY SERVICE: Registering your product will

help you obtain more efficient warranty service in case

there is a problem with yourproduct.

• CONFIRMATION OF OWNERSHIP: In case of

an insurance loss, such as fire, flood or theft, your

registration of ownership will serve as your proof

ofpurchase.

• FOR YOUR SAFETY: Registering your product will

allow us to contact you in the unlikely event a safety

notification is required under the Federal Consumer

SafetyAct.

Three Year Limited Warranty

DeWALT

will repair, without charge, any defects due to

faulty materials or workmanship for three years from the

date of purchase. This warranty does not cover part failure

due to normal wear or tool abuse. For further detail of

warranty coverage and warranty repair information, visit

www.dewalt.com or call 1-800-4-

DeWALT

(1-800-433-9258).

This warranty does not apply to accessories or damage

caused where repairs have been made or attempted by

others. This warranty gives you specific legal rights and

you may have other rights which vary in certain states

orprovinces.

In addition to the warranty,

DeWALT

tools are covered

byour:

1 YEAR FREE SERVICE

DeWALT

will maintain the tool and replace worn parts

caused by normal use, for free, any time during the first year

afterpurchase.

2 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DC9071, DC9091, DC9096, DC9182, DC9280, DC9360, DCB120,

DCB127, DCB201, DCB203, DCB203BT, DCB207, DCB361

3 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DCB200, DCB204, DCB204BT, DCB205, DCB606

NOTE: Battery warranty voided if the battery pack is

tampered with in any way.

DeWALT

is not responsible

for any injury caused by tampering and may prosecute

warranty fraud to the fullest extent permitted bylaw.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of

your

DeWALT

Power Tool, Laser, or Nailer for any reason, you

can return it within 90 days from the date of purchase with

a receipt for a full refund – no questionsasked.

LATIN AMERICA: This warranty does not apply to products

sold in Latin America. For products sold in Latin America,

see country specific warranty information contained in

the packaging, call the local company or see website for

warrantyinformation.

FREE WARNING LABEL REPLACEMENT: If your warning

labels become illegible or are missing, call 1-800-4-

DeWALT

(1-800-433-9258) for a freereplacement.

SPECIFICATIONS

DCE350

Battery Pack 20V Max*

Nominal Ram Force 6 Tons (53.5kN)

Operating Temperature Range 14 °F–158 °F (-10 °C–70 °C)

ENGLISH

Troubleshooting Guide

BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS

Problem Possible Cause Possible Solution

Tool does not turn ON when power ON/OFF

switch is pressed.

Battery is not charged. Charge battery or use a new, fully charged battery.

Battery is not fully inserted into tool. Remove battery and reinsert fully into the tool.

Tool does not respond when trigger switch

is pressed.

Battery is too low to complete a crimp/press. Battery

LED lights in red continuously.

Recharge battery in compatible D

WALT charger.

Other causes Refer to LED Indications for additional

information.

Tool is plugged into computer via micro

USB cable but the maintenance LED does

not light blue continuously.

Micro USB cable is not the provided cable and may

only be a "charging" cable, not a "data" cable.

Use the provided data cable.

CRIMP CONNECT™ System software is not

working properly.

Other causes View the FAQ page and help screens located

inside the CRIMP CONNECT™ System software.

ENGLISH

LED Indications

INDICATION USER ACTION LEDs EXAMPLE

Unit Power

Unit ON Press ON/OFF button All 3 LEDs light in green for 1 second.

GREEN

Unit OFF Press ON/OFF button All 3 LEDs light in red for 1 second.

RED

USB

Plug tool into computer

via USB

Maintenance LED lights in blue continuously.

NOTE: Indication is permanent as soon as tool is plugged in via USB.

BLUE

Battery

Full Charge Battery LED lights in green continuously.

NOTE: Indication is permanent as soon as tool is switched on.

GREEN

Medium

Charge

Battery LED lights in yellow continuously.

NOTE: Indication is permanent as soon as tool is switched on.

YELLOW

Low Charge Battery LED lights in red for 10 seconds, then tool turns off automatically.

NOTE: Indication is permanent as soon as tool is switched on.

RED

Crimp/Press Cycle

Cycle

Complete

Attempt a crimp/press Cycle Complete LED flashes in green for 5 seconds.

GREEN

Cycle Not

Complete

Attempt a crimp/press Cycle Complete LED flashes in red for 5 seconds.

NOTE: No action is possible until user presses ON/OFF button.

RED

Maintenance

Warning

Maintenance LED lights in yellow continuously.

NOTE: 500 cycles left. Indication is permanent as soon as tool is

switched on.

YELLOW

Final

Maintenance

Warning

Maintenance LED flashes in yellow continuously.

NOTE: 100 cycles left. Indication is permanent as soon as tool is

switched on.

YELLOW

Needs Service Maintenance LED lights in red for 10 seconds, then tool turns

off automatically.

NOTE: 0 cycles left.

RED

Temperature

Out of Range

Maintenance and Cycle Complete LEDs light in red continuously.

NOTE: Indication is permanent as soon as tool is switched on.

LEDs turn off when acceptable temperature is reached.

RED

FRANÇAIS



AVERTISSEMENT! lire tous les avertissements de

sécurité et toutes les directives. Le non-respect

des avertissements et des directives pourrait se

solder par un choc électrique, un incendie et/ou une

blessuregrave.

AVERTISSEMENT : afin de réduire le risque de

blessures, lire le mode d’emploi del’outil.

Goujons d’indentation

Verrou

Goupille de verrouillage

Anneau de suspension

de la bandoulière

Inverseur

Gâchette

Poignée principale

Lampe DEL

Bouton de libération du

bloc-piles

Bloc-piles

Écran de diagnostic

Interrupteur MARCHE/

ARRÊT

Port micro USB

Dispositif de fixation de

la bandoulière

Définitions : symboles et termes d'alarmes sécurité

Ces guides d'utilisation utilisent les symboles et termes d'alarmes sécurité suivants pour vous prévenir de situations

dangereuses et de risques de dommages corporels ou matériels.



DANGER: indique une situation dangereuse imminente qui, si elle n’est pas évitée, entraînera la mort ou des

blessuresgraves.



AVERTISSEMENT: indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait entraîner la

mort ou des blessuresgraves.



ATTENTION: indique une situation potentiellement dangereuse qui, si elle n’est pas évitée, pourrait entraîner des

blessures légères oumodérées.



(Si utilisé sans aucun terme) Indique un message propre à la sécurité.

AVIS : indique une pratique ne posant aucun risque de dommages corporels mais qui par contre, si rien n’est fait

pour l’éviter, pourrait poser des risques de dommages matériels.

FIG. A

Français (traduction de la notice d’instructions originale)

FRANÇAIS

CONSERVER TOUS LES

AVERTISSEMENTS ET TOUTES

LES DIRECTIVES POUR UN USAGE

ULTÉRIEUR

AVERTISSEMENTS DE SÉCURITÉ GÉNÉRAUX

POUR LES OUTILS ÉLECTRIQUES

Le terme « outil électrique » cité dans les avertissements se

rapporte à votre outil électrique à alimentation sur secteur

(avec fil) ou par piles (sans fil).



AVERTISSEMENT! lire tous les avertissements de

sécurité et toutes les directives. Le non-respect

des avertissements et des directives pourrait se

solder par un choc électrique, un incendie et/ou une

blessuregrave.

Sécurité du lieu de travail

a ) Tenir l’aire de travail propre et bien éclairée.

Les lieux encombrés ou sombres sont propices

auxaccidents.

b ) Ne pas faire fonctionner d’outils électriques

dans un milieu déflagrant, tel qu’en présence de

liquides, de gaz ou de poussières inflammables.

Les outils électriques produisent des étincelles qui

pourraient enflammer la poussière ou lesvapeurs.

c ) Éloigner les enfants et les personnes à proximité

pendant l’utilisation d’un outil électrique. Une

distraction pourrait en faire perdre la maîtrise à

l’utilisateur.

Sécurité en matière d’électricité

d ) Les fiches des outils électriques doivent

correspondre à la prise. Ne jamais modifier la

fiche d’aucune façon. Ne jamais utiliser de fiche

d’adaptation avec un outil électrique mis à la

terre. Le risque de choc électrique sera réduit par

l’utilisation de fiches non modifiées correspondant à

laprise.

e ) Éviter tout contact physique avec des surfaces

mises à la terre comme des tuyaux, des

radiateurs, des cuisinières et des réfrigérateurs.

Le risque de choc électrique est plus élevé si votre corps

est mis à laterre.

f ) Ne pas exposer les outils électriques à la pluie ou

à l’humidité. La pénétration de l’eau dans un outil

électrique augmente le risque de chocélectrique.

g ) Ne pas utiliser le cordon de façon abusive.

Ne jamais utiliser le cordon pour transporter,

tirer ou débrancher un outil électrique. Tenir le

cordon éloigné de la chaleur, de l’huile, des bords

tranchants et des pièces mobiles. Les cordons

endommagés ou enchevêtrés augmentent les risques

de chocélectrique.

h ) Pour l’utilisation d’un outil électrique à

l’extérieur, se servir d’une rallonge convenant à

cette application. L’utilisation d’une rallonge conçue

pour l’extérieur réduira les risques de chocélectrique.

i ) S’il est impossible d’éviter l’utilisation d’un

outil électrique dans un endroit humide,

brancher l’outil dans une prise ou sur un circuit

d’alimentation dotés d’un disjoncteur de fuite à

la terre (GFCI). L’utilisation de ce type de disjoncteur

réduit les risques de chocélectrique.

Sécurité personnelle

j ) Être vigilant, surveiller le travail effectué et faire

preuve de jugement lorsqu’un outil électrique

est utilisé. Ne pas utiliser d’outil électrique en

cas de fatigue ou sous l’influence de drogues,

d’alcool ou de médicaments. Un simple moment

d’inattention en utilisant un outil électrique peut

entraîner des blessures corporellesgraves.

k ) Utiliser des équipements de protection

individuelle. Toujours porter une protection

oculaire. L’utilisation d’équipements de protection

comme un masque antipoussière, des chaussures

antidérapantes, un casque de sécurité ou des

protecteurs auditifs lorsque la situation le requiert

réduira les risques de blessurescorporelles.

l ) Empêcher les démarrages intempestifs. S’assurer

que l’interrupteur se trouve à la position

d’arrêt avant de relier l’outil à une source

d’alimentation et/ou d’insérer un bloc-piles, de

ramasser ou de transporter l’outil. Transporter

un outil électrique alors que le doigt repose sur

l’interrupteur ou brancher un outil électrique dont

l’interrupteur est à la position de marche risque de

provoquer unaccident.

m ) Retirer toute clé de réglage ou clé avant de

démarrer l’outil. Une clé ou une clé de réglage

attachée à une partie pivotante de l’outil électrique

peut provoquer des blessurescorporelles.

n ) Ne pas trop tendre les bras. Conserver

son équilibre en tout temps. Cela permet

de mieux maîtriser l’outil électrique dans les

situationsimprévues.

o ) S’habiller de manière appropriée. Ne pas porter

de vêtements amples ni de bijoux. Garder les

cheveux, les vêtements et les gants à l’écart des

pièces mobiles. Les vêtements amples, les bijoux ou

les cheveux longs risquent de rester coincés dans les

piècesmobiles.

p ) Si des composants sont fournis pour le

raccordement de dispositifs de dépoussiérage

et de ramassage, s’assurer que ceux-ci sont bien

raccordés et utilisés. L’utilisation d’un dispositif de

dépoussiérage peut réduire les dangers engendrés par

lespoussières.

q ) Ne pas laisser la familiarisation gagnée par

l’utilisation fréquente des outils vous amener

à la négligence et à ignorer les principes de

sécurité propres à l’outil. Une imprudence pourrait

causer des dommages corporels graves en une

fraction de seconde.

Utilisation et entretien d’un outil

électrique

r ) Ne pas forcer un outil électrique. Utiliser l’outil

électrique approprié à l’application. L’outil

électrique approprié effectuera un meilleur travail,

de façon plus sûre et à la vitesse pour laquelle il a

étéconçu.

FRANÇAIS

s ) Ne pas utiliser un outil électrique dont

l’interrupteur est défectueux. Tout outil électrique

dont l’interrupteur est défectueux est dangereux et

doit êtreréparé.

t ) Débrancher la fiche de la source d’alimentation

et/ou du bloc-piles de l’outil électrique avant de

faire tout réglage ou changement d’accessoire

ou avant de ranger l’outil. Ces mesures préventives

réduisent les risques de démarrage accidentel de

l’outilélectrique.

u ) Ranger les outils électriques hors de la portée

des enfants et ne permettre à aucune personne

n’étant pas familière avec un outil électrique ou

son mode d’emploi d’utiliser cet outil. Les outils

électriques deviennent dangereux entre les mains

d’utilisateursinexpérimentés.

v ) Entretien des outils électriques. Vérifier si les

pièces mobiles sont mal alignées ou coincées,

si des pièces sont brisées ou présentent toute

autre condition susceptible de nuire au bon

fonctionnement de l’outil électrique. En cas de

dommage, faire réparer l’outil électrique avant

toute nouvelle utilisation. Beaucoup d’accidents

sont causés par des outils électriques malentretenus.

w ) S’assurer que les outils de coupe sont aiguisés et

propres. Les outils de coupe bien entretenus et affûtés

sont moins susceptibles de se coincer et sont plus

faciles àmaîtriser.

x ) Utiliser l’outil électrique, les accessoires, les

forets, etc. conformément aux présentes

directives en tenant compte des conditions de

travail et du travail à effectuer. L’utilisation d’un

outil électrique pour toute opération autre que celle

pour laquelle il a été conçu estdangereuse.

y ) Maintenir les poignées et les surfaces de

préhension propres et sèches, exemptes

d’huile ou de graisse. Des poignées ou surfaces

de préhension glissantes ne permettent pas la

manipulation sécuritaire et le contrôle de l’outil dans

les situations inattendues.

Utilisation et entretien du bloc-piles

z ) Ne recharger l’outil qu’au moyen du chargeur

précisé par le fabricant. L’utilisation d’un chargeur

qui convient à un type de bloc-piles risque de

provoquer un incendie s’il est utilisé avec un autre type

de b loc-piles.

aa ) Utiliser les outils électriques uniquement avec

les blocs-piles conçus à cet effet. L’utilisation de

tout autre bloc-piles risque de causer des blessures ou

unincendie.

ab ) Lorsque le bloc-piles n’est pas utilisé, le tenir

éloigné des objets métalliques, notamment

des trombones, de la monnaie, des clés, des

clous, des vis ou autres petits objets métalliques

qui peuvent établir une connexion entre les

deux bornes. Le court-circuit des bornes du bloc-piles

risque de provoquer des brûlures ou unincendie.

ac ) En cas d’utilisation abusive, le liquide peut gicler

hors du bloc-piles; éviter tout contact avec ce

liquide. Si un contact accidentel se produit, laver

à grande eau. Si le liquide entre en contact avec

les yeux, obtenir également des soins médicaux.

Le liquide qui gicle hors du bloc-piles peut provoquer

des irritations ou desbrûlures.

ad ) Ne pas utiliser un bloc-piles ou un outil

endommagé ou modifié. Un bloc-piles endommagé

ou modifié pourrait se comporter de façon

imprévisible et poser des risques d’incendie, d’explosion

ou de dommages corporels.

ae ) Ne pas exposer un bloc-piles ou un outil au feu,

ou à des températures excessives. Toute exposition

au feu ou à des températures supérieures à 130°C

pose des risques d’explosion.

af ) Suivre toutes les instructions de chargement

et ne pas recharger un bloc-piles ou un outil

hors des températures d’emploi spécifiées dans

les directives. Un chargement incorrect ou à des

températures hors des plages spécifiées pourrait

endommager le bloc-piles et augmenter les risques

d’incendie.

Réparation

ag ) Faire réparer l’outil électrique par un réparateur

professionnel en n’utilisant que des pièces de

rechange identiques. Cela permettra de maintenir

une utilisation sécuritaire de l’outilélectrique.

ah ) Ne jamais réparer un bloc-piles endommagé.

Toute réparation d’un bloc-piles devrait être effectuée

par le fabricant ou des services agréés.

Règles de sécurité additionnelles propres

aux sertisseuses



DANGER: utiliser exclusivement des connecteurs

et des câbles en combinaison agréée par le

fabricant pour réussir l’installation. Combiner

du matériel qui n’est pas approuvé par les

fabricants pourra avoir comme conséquences

des installations défectueuses. Les installations

défectueuses posent des risques de défaillances

extrêmement graves, de dommages corporels

pour les installateurs et de dommages matériels.



DANGER: pour réduire tout risque de

dommages corporels graves, couper le circuit

électrique avant d’effectuer un sertissage.

Tout manquement à cette directive avant

de commencer le travail pose des risques de

dommages corporels ou matériels graves ou de

fatalité.



AVERTISSEMENT: utiliser l’outil de sertissage

exclusivement pour l’utilisation pour laquelle

il a été conçu. Toute autre utilisation ou

modification de la sertisseuse pour d’autres

applications pourra endommager la sertisseuse

et/ou causer des dommages corporels ou créer

des connexions défectueuses.



AVERTISSEMENT: bien que cette sertisseuse

DeWALT

atteindra la pression adéquate pour

effectuer au mieux le sertissage, la sertissure

ne sera correctement effectuée que dans

la mesure où la connexion ne sera affectée

d’aucun défaut et que l’outil sera préparé

conformément à la procédure d’installation

FRANÇAIS

du connecteur du fabricant. La préparation et

l’installation correctes restent la responsabilité

de l’entrepreneur chargé de l’installation.

• Protéger toutes les parties du corps de la tête de

la sertisseuse pendant son utilisation et tant que

l’outil sera EN MARCHE. Tout moment d’inattention

pendant l’utilisation d’un outil électrique pose des

risques de blessures graves. Les doigts ou les mains

pourraient être écrasés, ou subir fractures ou amputation

s’ils venaient à entrer en contact avec les goujons

d’indentation ou les pièces mobiles.

• Vérifier outil et goujons d’indentation avant chaque

utilisation. Ne jamais tenter de réparer la tête

de la sertisseuse ou les goujons d’indentation si

endommagés. Des goujons d’indentation modifiés, peu

importe la façon, pourront se fêler pendant la sertissure

et poser des risques de dommages corporels graves. Le

remplacement ou la réparation de la tête de la sertisseuse

pourra s’avérer nécessaire.

• Cet outil produit des forces importantes qui

pourraient briser des pièces et causer des dommages

corporels. Rester systématiquement attentif et prendre

les mesures de sécurité adéquates, y compris le port d’une

protection oculaire.

• Ne jamais faire fonctionner l’outil avec des goujons

d’indentation endommagés.

• Ne jamais effectuer une sertissure alors que le

verrou ou la goupille de verrouillage est ouvert.

• Cet outil doit être utilisé exclusivement par du

personnel qualifié.

• Avant chaque utilisation, vérifier l’outil et les

voyants DEL sur l’écran de diagnostic. Corriger tout

problème avant d’utiliser l’outil. Se reporter à la section

Dépannage pour avoir la liste des problèmes possibles et

leurs solutions.

• Avant toute utilisation de la sertisseuse

DeWALT

DCE350, lire et comprendre toutes les instructions

quant à la sécurité et à l’utilisation, y compris

les instructions d’installation du fabricant du

connecteur et les instructions accompagnant tout

accessoire utilisé avec cet outil. Tout manquement

aux instructions et avertissements pose des risques

de dommages matériels et/ou corporels graves.

• Risques d’écrasement. Éloigner de la zone de

sertissage de l’outil, les mains et tout autre objet

pendant toute la durée d’utilisation de l’outil. Il y a

risques d’écrasement pour les doigts.

• Arrimer et soutenir le matériau avant d’effectuer le

sertissage pour prévenir tout mouvement pendant

la sertissure.

• Suivre la notice d’installation du fabricant du

connecteur. Toute autre utilisation pourrait endommager

l’outil, les accessoires et la pièce à travailler.

• Maintenir systématiquement l’outil fermement. Les

forces appliquées sur l’outil peuvent changer pendant ou

après la sertissure.

• Porter systématiquement une protection oculaire. Le

sertissage peut faire que des débris de matériau s’envolent.

Et ces particules posent des risques de dommages

oculaires permanents.

• Porter systématiquement des gants pendant

l’utilisation de l’outil et pour manipuler les

matériaux. Les extrémités des matériaux peuvent être

acérées et poser des risques de dommages corporels

graves.

• Porter systématiquement des souliers de sécurité pour

protéger les pieds de tout débris métallique acéré tombé

sur le sol.

Instructions additionnelles de sécurité



AVERTISSEMENT: porter SYSTEMATIQUEMENT

des lunettes de protection. Les lunettes courantes

NE sont PAS des lunettes de protection. Utiliser aussi

un masque antipoussières si la découpe doit en

produire beaucoup. PORTER SYSTÉMATIQUEMENT UN

ÉQUIPEMENT DE SÉCURITÉ HOMOLOGUÉ:

• Protection oculaire ANSI Z87.1 (CAN/CSA Z94.3);

• Protection auditive ANSI S12.6 (S3.19);

• Protection des voies respiratoires NIOSH/OSHA/

MSHA.



AVERTISSEMENT: les scies, meules, ponceuses,

perceuses ou autres outils de construction peuvent

produire des poussières contenant des produits

chimiques reconnus par l’État californien pour causer

cancers, malformations congénitales ou être nocifs au

système reproducteur. Parmi ces produits chimiques,

on retrouve:

• Le plomb dans les peintures à base de plomb;

• La silice cristallisée dans les briques et le ciment,

ou autres produits de maçonnerie; et

• L’arsenic et le chrome dans le bois ayant subi un

traitementchimique.

Le risque associé à de telles expositions varie selon la

fréquence à laquelle on effectue ces travaux. Pour réduire

toute exposition à ces produits: travailler dans un endroit

bien aéré, en utilisant du matériel de sécurité homologué, tel

un masque antipoussières spécialement conçu pour filtrer les

particulesmicroscopiques.

• Limiter toute exposition prolongée avec les

poussières provenant du ponçage, sciage, meulage,

perçage ou toute autre activité de construction.

Porter des vêtements de protection et nettoyer à

l’eau savonneuse les parties du corps exposées. Le

fait de laisser la poussière pénétrer dans la bouche, les

yeux ou la peau peut favoriser l’absorption de produits

chimiquesdangereux.



AVERTISSEMENT: cet outil peut produire et/

ou répandre de la poussière susceptible de causer

des dommages sérieux et permanents au système

respiratoire. Utiliser systématiquement un appareil

de protection des voies respiratoires homologué par

le NIOSH ou l’OSHA. Diriger les particules dans le sens

opposé au visage et aucorps.



AVERTISSEMENT: pendant l’utilisation, porter

systématiquement une protection auditive

individuelle adéquate homologuée ANSI S12.6

(S3.19). Sous certaines conditions et suivant la durée

d’utilisation, le bruit émanant de ce produit pourrait

contribuer à une perte de l’acuitéauditive.



ATTENTION: après utilisation, ranger l’outil

sur son côté, sur une surface stable, là où il

ne pourra ni faire trébucher ni faire chuter

quelqu’un. Certains outils équipés d’un large bloc-

FRANÇAIS

piles peuvent tenir à la verticale sur celui-ci, mais

manquent alors destabilité.

• Prendre des précautions à proximité des évents,

car ils cachent des pièces mobiles. Vêtements amples,

bijoux ou cheveux longs risquent de rester coincés dans

ces piècesmobiles.

L’étiquette apposée sur votre outil peut inclure les symboles

suivants. Les symboles et leur définition sont indiqués ci-après:

V ......................... volts

Hz ....................... hertz

min ..................... minutes

or DC ...... courant continu

...................... fabrication classe I

(mis à la terre)

…/min .............. par minute

BPM .................... battements par

minute

IPM ..................... impacts par minute

RPM .................... revolutions per

minute

sfpm ................... pieds linéaires par

minute (plpm)

SPM (FPM) ......... fréquence par

minute

A ......................... ampères

W ........................ watts

or AC ........... courant alternatif

or AC/DC .... courant alternatif

ou continu

...................... fabrication classe II

(double isolation)

........................ vitesse à vide

n ......................... vitesse nominale

...................... borne de terre

...................... symbole

d’avertissement

..................... radiation visible

..................... protection

respiratoire

.....................protection oculaire

.....................protection auditive

..................... risques

d’écrasement

..................... risques de chocs

électriques

..................... lire toute la

documentation

BLOCS-PILES ET CHARGEURS

Le bloc-piles n’est pas totalement chargé d’usine. Avant

d’utiliser le bloc-piles et le chargeur, lire les consignes de

sécurité ci-après puis suivre la procédure de chargement

indiquée. Pour commander un bloc-piles de rechange,

s’assurer d’en inclure le numéro de catalogue et la tension.

Cet outil fonctionne avec un chargeur

DeWALT

. S’assurer

de bien lire toutes les consignes de sécurité avant toute

utilisation du chargeur. Consulter le tableau en fin de

manuel pour connaître les compatibilités entre chargeurs

et blocs-piles.

LIRE TOUTES LES CONSIGNES

Consignes importantes de sécurité

les blocs-piles



AVERTISSEMENT : Lire toutes les instructions et

toutes les consignes de sécurité propres au bloc-

piles, au chargeur et à l’outil électrique. Tout

manquement aux avertissements et instructions

pose des risques de décharges électriques,

d’incendie et/ou de blessures graves.

• Ne pas recharger ou utiliser un bloc-piles en milieu

déflagrant, en présence, par exemple, de poussières,

gaz ou liquides inflammables. Le fait d’insérer ou

retirer un bloc-piles de son chargeur pourrait causer

l’inflammation de poussières ou d’émanations.

• NE JAMAIS forcer l’insertion d’un bloc-piles dans un

chargeur. NE modifier un bloc-piles d’AUCUNE façon

pour le faire rentrer dans un chargeur incompatible,

car il pourrait se briser et causer des dommages

corporels graves. Consulter le tableau en dernière page

de ce manuel pour connaître les compatibilités entre

chargeurs et blocs-piles.

• Recharger les blocs-piles exclusivement dans des

chargeurs

DeWALT

• NE PAS éclabousser le bloc-piles ou l’immerger dans l’eau

ou dans tout autreliquide.

• Ne pas entreposer ou utiliser l’appareil et le bloc-

piles en présence de températures ambiantes

pouvant excéder 40°C (104°F) (comme dans des

hangars ou des bâtiments métalliques l’été). Pour

préserver leur durée de vie, entreposer les blocs-piles dans

un endroit frais etsec.

REMARQUE: ne pas mettre un bloc-piles dans un

outil dont la gâchette est verrouillée en position de

marche. Ne jamais bloquer l’interrupteur en position

deMARCHE.

• Ne pas incinérer le bloc-piles même s’il est

sévèrement endommagé ou complètement usagé,

car il pourrait exploser et causer un incendie.

Pendant l’incinération des blocs-piles au lithium-ion, des

vapeurs et matières toxiques sontdégagées.

• En cas de contact du liquide de la pile avec la peau,

rincer immédiatement au savon doux et à l’eau. En

cas de contact oculaire, rincer l’œil ouvert à l’eau claire

une quinzaine de minutes ou jusqu’à ce que l’irritation

cesse. Si des soins médicaux s’avéraient nécessaires, noter

que l’électrolyte de la pile est composé d’un mélange de

carbonates organiques liquides et de sels delithium.

• Le contenu des cellules d’une pile ouverte peut

causer une irritation respiratoire. En cas d’inhalation,

exposer l’individu à l’air libre. Si les symptômes persistent,

consulter unmédecin.



AVERTISSEMENT: risques de brûlure. Le liquide de la

pile peut s’enflammer s’il est exposé à des étincelles ou

à uneflamme.



AVERTISSEMENT: risques d’incendie. Ne jamais

tenter d’ouvrir le bloc-piles pour quelque raison

que ce soit. Si le boîtier du bloc-piles est fissuré ou

endommagé, ne pas l’insérer dans un chargeur. Ne

pas écraser, laisser tomber, ou endommager les blocs-

piles. Ne pas utiliser un bloc-piles ou un chargeur

qui a reçu un choc violent, ou si l’appareil est tombé,

a été écrasé ou endommagé de quelque façon que

ce soit (p. ex. percé par un clou, frappé d’un coup

de marteau, piétiné). Les blocs-piles endommagés

doivent être renvoyés à un centre de réparation pour

y êtrerecyclés.

Transport



AVERTISSEMENT: risques d’incendie. Au moment

de ranger ou transporter le bloc-piles, veiller à

protéger ses bornes à découvert de tout objet

métallique. Par exemple, éviter de placer le bloc-

piles dans un tablier, une poche, une boîte à outils

ou un tiroir, etc. contenant des objets tels que clous,

vis, clés, etc. Le fait de transporter des blocs-piles

comporte des risques d’incendie, car les bornes

des piles pourraient entrer, par inadvertance,

en contact avec des objets conducteurs, tels

La page charge ...

DeWalt DCE350M2 Mode d'emploi

Marque: DeWalt

Modèle: DCE350M2

Catégorie: Outils électroportatifs

Taper: Mode d'emploi

Ce manuel convient également à

DCE350M2w150b

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt DCE350M2 User guide
español: DeWalt DCE350M2 Guía del usuario

DeWalt DCE350M2 Mode d'emploi

Ce manuel convient également à

DeWalt DCE350M2 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents