Roper RS25AFXRD01 Le manuel du propriétaire

Marque: Roper

Modèle: RS25AFXRD01

Catégorie: Frigos

Taper: Le manuel du propriétaire

BY WHIRLPOOL CORPORATION

SIDEBYSIDE

REFRIGERATOR

For questions about features, operation/performance, parts,

accessories or service, call: 1-800-44-ROPER (1-800-447-6737).

In Canada, call for assistance 1-800-461-5681, for installation

and service, call: 1-800-807-6777

or visit our website at...

www.rope ra pplian ces.com

RI_FRIGI_RATEUR

C&TEC6TE

o_I_ _:_,n_:__?n

Au Canada, pour assistance, composez le 1-800-461-5681,

pour installation ou service le 1-800-807-6777

ou visitez notre site web &...

www.roperappliances.com/canada

Table of Contents/Table des matieres .................. 2

2188763

TABLEOFCONTENTS

REFRIGERATOR SAFETY ............................................................. 3

Proper Disposal of Your Old Refrigerator .................................... 3

INSTALLATION INSTRUCTIONS .................................................. 4

Unpacking .................................................................................... 4

Location Requirements ................................................................ 4

Electrical Requirements ............................................................... 5

Water Supply Requirements ........................................................ 5

Base Grille .................................................................................... 5

Door Removal ............................................................................... 6

Door Closing ................................................................................. 8

Water Supply Connection ............................................................ 8

Water System Preparation ........................................................... 9

Normal Sounds .......................................................................... 10

REFRIGERATOR USE .................................................................. 10

Ensuring Proper Air Circulation .................................................. 10

Using the Controls ..................................................................... 10

Water and Ice Dispensers .......................................................... 11

Water Filter Status Light ............................................................. 12

Water Filtration System .............................................................. 12

Ice Maker and Storage Bin ........................................................ 13

REFRIGERATOR FEATURES ...................................................... 14

Refrigerator Shelves ................................................................... 14

Flip-up Shelf ............................................................................... 14

Adjustable Flip-up Shelf ............................................................. 14

Dell Drawer ................................................................................. 14

Convertible Vegetable/Meat Drawer, Crisper and Covers ........15

Convertible Vegetable/Meat Drawer Temperature Control .......15

Crisper Humidity Control ........................................................... 15

Wine or Can/Bottle Rack ........................................................... 15

Utility Bin .................................................................................... 15

FREEZER FEATURES .................................................................. 16

Freezer Shelf .............................................................................. 16

Freezer Basket or Bin................................................................. 16

DOOR FEATU RES ........................................................................ 16

Door Rails ................................................................................... 16

Can Racks and Door Bins.......................................................... 16

REFRIGERATOR CARE ............................................................... 17

Cleaning ...................................................................................... 17

Changing the Light Bulbs ........................................................... 17

Power Interruptions .................................................................... 18

Vacation and Moving Care ......................................................... 18

TROUBLESHOOTING .................................................................. lg

ASSISTANCE OR SERVICE ......................................................... 21

In the U.S.A ................................................................................ 21

In Canada ................................................................................... 22

Accessories ................................................................................ 22

WATER FILTER CERTIFICATIONS ............................................. 22

PRODUCT DATA SHEETS ........................................................... 23

WARRANTY .................................................................................. 24

TABLEDESMATIERES

SECURITE DU REFRIGERATEUR .............................................. 25

Mise au rebut de votre vieux refrigerateur ................................. 25

INSTRUCTIONS D'INSTALLATION ............................................. 26

Deballage .................................................................................... 26

Emplacement d'installation ........................................................ 26

Specifications electriques .......................................................... 27

Specifications de I'alimentation en eau ..................................... 27

Grille de la base .......................................................................... 27

Enlevement des portes ............................................................... 28

Fermeture des portes ................................................................. 30

Raccordement de la canalisation d'eau .................................... 30

Preparation du systeme d'eau ................................................... 32

Sons normaux ............................................................................ 32

UTILISATION DU REFRIGERATEUR .......................................... 32

Pour s'assurer d'une circulation d'air appropriee ...................... 32

Utilisation des commandes ........................................................ 33

Distributeurs d'eau et de gla9ons .............................................. 33

Le temoin lumineux de I'etat du filtre a eau ............................... 34

Systeme de filtration d'eau ........................................................ 35

Machine a gla(_ons et bac .......................................................... 36

CARACTERISTIQUES DU REFRIGERATEUR ........................... 36

Tablettes du refrigerateur ........................................................... 37

Tablette relevable ....................................................................... 37

Tablette relevable ajustable ....................................................... 37

Tiroir pour specialites alimentaires ............................................ 37

Tiroir a legumes/viande convertible,

bac a legumes et couvercles ..................................................... 37

Reglage de la temperature du tiroir

legumes/viande convertible ....................................................... 38

Reglage de I'humidite darts le bac a legumes ........................... 38

Casier a vin ou porte-cannettes/bouteilles ................................ 39

Casier utilitaire ............................................................................ 39

CARACTERISTIQUES DU CONGELATEUR ............................... 39

Tablette de congelateur ............................................................. 39

Panier ou bac de congelateur .................................................... 39

CARACTERISTIQUES DE LA PORTE ......................................... 39

Tringles darts la porte ................................................................. 39

Porte-cannettes et balconnets ................................................... 40

ENTRETIEN DU REFRIGERATEUR ............................................ 40

Nettoyage ................................................................................... 40

Remplacement des ampoules d'eclairage ................................ 41

Pannes de courant ..................................................................... 42

Entretien avant les vacances ou Iors d'un demenagement .......42

DEPANNAGE ................................................................................. 43

ASSISTANCE OU SERVICE ......................................................... 46

Accessoires ................................................................................ 46

FEUlLLES DE DONNEES SUR LE PRODUIT ............................. 47

GARANTI E ..................................................................................... 48

REFRIGERATORSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance, Always read and obey all

safety messages.

This is the safety alert symbol,

This symbol alerts you to potential hazards that can kill or hurt you and others,

All safety messages will follow the safety alert symbol and either the word "DANGER" or

"WARNING," These words mean:

You can be killed or seriously injured if you don't

immediately follow instructions.

You can be killed or seriously injured if you don't

follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you

what can happen if the instructions are not followed,

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic

precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all panels before operating.

• Remove doors from your old refrigerator.

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

• Use two or more people to move and install

refrigerator.

• Disconnect power before installing ice maker (on

ice maker kit ready models only).

• Use a sturdy glass when dispensing ice or water

(on some models).

SAVE THESE INSTRUCTIONS

ProperDisposalof

YourOld Refrigerator

Before you throw away your old refrigerator or freezer:

• Take off the doors.

• Leave the shelves in place so that children may not easily

climb inside.

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can resuJt in death or

brain damage.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." Ifyou are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

INSTALLATIONINSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

Removing packaging materials

• Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with warm water

and dry.

Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see the "Refrigerator Safety" section.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator

for cieaning or service, be sure to protect the floor.

Always pull the refrigerator straight out when moving it.

Do not wiggle or "walk" the refrigerator when trying to move

it, as floor damage could occur.

Cleaning before use

After you remove all of the packaging materials, clean the inside

of your refrigerator before using it. See the cleaning instructions

in the "Refrigerator Care" section.

Important information to know about gmaes shemves

an_ covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass

shelves and covers are heavy. Use special care when re-

moving them to avoid impact from dropping.

Explosion Hazard

Keep flammabJe materials and vapors, such as

gasoline, away from refrigerator.

Faiture to do so can result in death, explosion,

or fire.

To ensure proper ventilation for your refrigerator, allow for 1/2in.

(1.25 cm) space on each side and at the top. When installing your

refrigerator next to a fixed wall, leave 2 in. (5.08 cm) minimum on

each side (depending on your model) to allow for the door to

swing open. If your refrigerator has an ice maker, allow extra

space at the back for the water line connections.

NOTE: Do not install the refrigerator near an oven, radiator, or

other heat source, nor in a location where the temperature will fall

below 55°F (13°C).

mjl,

V2" (1.25 cm)

II -- I!

2" (5°08cm)

ElectrbalShockHazard

Plugintoagrounded3prongoutbt.

Donotremovegroundprong.

Donotuseanadapter.

Donotuse an e×tension cord.

Failure to follow these instructions can result in

death, fire, or electricaJ shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical

connection.

Recommended grounding method

A 115 Volt, 60 Hz., AC only 15 or 20 ampere fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the control (Thermostat, Refrigerator

or Freezer Control depending on the model) to OFF and then

disconnect the refrigerator from the electrical source. When you

are finished, reconnect the refrigerator to the electrical source

and reset the control (Thermostat, Refrigerator or Freezer Control

depending on the model) to the desired setting.

Read alldirectionscarefullybeforeyou begin.

IMPORTANT."

• Ifyou turntherefrigeratoron beforethe waterlineis

connected,turnthe icemaker OFE

• All installations must meet local plumbing code requirements.

• Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

Tools Required: Flat-blade screwdriver, 7_ in. and _/_in. open-

end wrenches or two adjustable wrenches,//4 in. nut driver and

drill bit, hand drill or electric drill (properly grounded).

NOTE: Your refrigerator dealer has a kit available with a//4 in.

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.

Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or 3_6in.

(4.76 mm) saddle valve which reduces water flow and clogs more

easily.

Water Pressure

A cold water supply with water pressure of between 30 and 120

psi (207-827 kPa) is required to operate the water dispenser and

ice maker. Ifyou have questions about your water pressure, see

"Troubleshooting" or call a licensed, qualified plumber.

Reverse Osmosis Water Supply

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the system needs to be

a minimum of 40 to 60 psi (276 - 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 - 414 kPa) a booster pump can be inserted into

the small tubing that goes from the cold water line to the reverse

osmosis system.

If the water dispenser is still not dispensing water properly:

• Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

If your refrigerator has a water filter cartridge, it may further

reduce the water pressure when used in conjunction with a

reverse osmosis system. Remove the water filter cartridge.

See "Water Filtration System."

If you have questions about your water pressure, refer to

"Troubleshooting" or call a licensed, qualified plumber.

To remove the base grille:

1. Open both doors.

2. Place hands along the ends of the grille, with your thumbs

along the top. Push in with your thumbs and pull up on the

bottom.

NOTE: Be sure to refasten the Tech Sheet behind the base grille

after cleaning.

To replace the base grille:

1. Open both doors.

2. Line up the grille support tabs with the metal clips.

3. Push the grille firmly to snap it into place.

TOOLSNEEDED:1/4in.hex-headsocketwrench,%6in.hex-headsocketwrenchandaflat-bladescrewdriver.

IMPORTANT:Beforeyoubegin,turntherefrigeratorcontrolOFEunplugrefrigeratorordisconnectpower.Removefoodandany

adjustabledoororutilitybinsfromdoors.

NOTE:Itmayonlybenecessarytoremoveeitherthedoorhandleorthedoorstogetyourproductthroughthedoorwayofyour

residence.Measurethedooropeningtodeterminewhethertoremovetherefrigeratorhandlesorthedoors.

Electrical Shock Hazard

Disconnect power before removing doors.

Reconnect both ground wires before operating.

Failure to do so can result in death or electrical shock.

Top Left Hinge

Style 1

Style 2

1. Do Not Remove Screw

Water Dispenser

Tubing Connection

Door RemovaJ

Top Right Hinge

1.Do Not Remove Screw

Bottom Hinge

1, Do Not Remove Screw

Door Alignment

1, LeveRing Screw

Handle Removal (optional)

1. Apply firm pressure with your hand on the face of trim. Slide

top trim up and bottom trim down away from handle. Lift trim

pieces off shoulder screws (see Graphic 1).

NOTE: Some models include accent pieces between the handle

and the handle trim. If your model includes the accents, you will

need to carefully remove them with a flat-blade screwdriver

before removing the handle screws. The accent pieces are

optional and can be reinstalled or left off of the handle assembly.

2. Remove handle screws and handles.

3. Move refrigerator into place. Replace handles as shown (see

Graphic 1).

Door Removal

EJectricai Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or

etectrica! shock.

1. Unplug refrigerator or disconnect power.

2. Open both refrigerator doors. Remove the base grille by

pulling up on the bottom outside corners (see Graphic 2).

3. Close both doors and keep them closed until you are ready to

lift them free from the cabinet.

4. If you have a dispenser (ice or water), disconnect the water

dispenser tubing located behind the base grille on the freezer

door side (see Graphic 3).

• Press the red outer ring against the face of fitting and pull

the dispenser tubing free.

• On some models, remove tubing from hose clip.

5. Remove top left hinge screw and cover as shown (see

Graphic 4). Do not remove screw 1.

6. Disconnect wiring:

Style 1

• Disconnect wiring plug.

• Remove green ground wire screw to disconnect ground

wires.

1.Do not remove screw 1

2. Ground wires

3. Green ground wire screw

4. Wiring plug

Style 2

• Disconnect wiring plug.

1. Do not remove screw !

2. Wiring plug

7. Carefully lift freezer door straight up off bottom hinge (see

Graphic 5). The water dispenser tubing remains attached to

the freezer door and pulls through the bottom left hinge.

Make sure you protect the dispenser tubing from damage.

8. Remove top right hinge cover and screws as shown (see

Graphic 6). Do not remove screw 1.

g. Lift the refrigerator door straight up off bottom hinge.

10. It may not be necessary to remove the bottom hinge to move

the refrigerator through a doorway. Both bottom hinges have

similar construction. If neccessary, disassemble the hinges as

shown (see Graphic 7). Do not remove screw 1.

Door and Hinge Replacement

1. Replace both bottom hinges, if removed. Tighten screws.

2. Assistance may be needed to feed the water dispenser

tubing through the bottom hinge while reinstalling the freezer

door. Carefully feed the dispenser tubing through the bottom

left hinge before replacing the door on the hinge.

NOTE: Provide additional support for the doors while the top

hinges are being replaced. Do not depend on the door magnets

to hold the doors in place while you are working.

3. Reconnect water dispenser tubing by pushing tubing into

fitting until it stops and black mark touches face of fitting (see

Graphic 3). On some models, replace tubing in hose clip.

4. Alignandreplacethetoplefthingeasshown(seeGraphic4).

Tightenscrews.

EtectricaJShockHazard

Reconnectbothgroundwires.

FaluretodosocanresuJtin deathor

eJectricaJshock.

Style1

• Reconnectbothgroundwires.

• Reconnectwiringplug.

Style 2

1. Do not remove screw 1

2. Ground wires

3. Green ground wire screw

4. Wiring plug

Reconnect wiring plug.

1.Do not remove screw !

2. Wiringplug

5. Replace left hinge cover and screws.

6. Replace the refrigerator door by carefully lifting the door onto

the bottom right hinge.

7. Align and replace the top right hinge as shown (see Graphic

6). Tighten screws.

8. Replace hinge cover and screws. Tighten screws.

9. Plug into a grounded 3 prong outlet.

Your refrigerator has two front adjustable rollers -- one on the

right and one on the left. If your refrigerator seems unsteady or if

you want the doors to close more easily, adjust the refrigerator's

tilt using the instructions below:

1. Move the refrigerator into its final position.

2. The two leveling screws are part of the front roller assemblies

which are at the base of the refrigerator on either side (see

Graphic 8).

Use a hex-head socket wrench to adjust the leveling screws.

Turn the leveling screw to the right to raise that side of the

refrigerator or turn the leveling screw to the left to lower that

side. It may take several turns of the leveling screws to adjust

the tilt of the refrigerator (see Graphic 8).

NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws and

rollers. This makes it easier to adjust the screws.

4. Open both doors again and check to make sure that they

close as easily as you like. If not, tilt the refrigerator slightly

more to the rear by turning both leveling screws to the right. It

may take several more turns, and you should turn both

leveling screws the same amount.

5. Replace the base grille.

NOTE: Be sure to refasten the Tech Sheet behind the base grille.

1. ,RI' Ii +_,,.,.IIOFI

,j,=.,,._l_.,_l+.,jW _'_+<= _ i>j.,<,,_ll<,, =

Read all directions before you begin.

IMPORTANT: If you turn the refrigerator on before the water line

is connected, turn the ice maker OFE

Connecting to Water Line

Unplug refrigerator or disconnect power.

Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

Locate a 1/2in. to 11/4in. (1.25 cm to 3.18 cm) vertical COLD

water pipe near the refrigerator.

NOTE: Horizontal pipe will work, but drill on the top side of

the pipe, not the bottom. This will help keep water away from

the drill and normal sediment from collecting in the valve.

Determine the length of copper tubing you need. Measure

from the connection on the lower left rear of refrigerator to the

water pipe. Add 7 ft. (2.1 m) to allow for cleaning. Use 1/4in.

(6.35 mm) O.D. (outside diameter) copper tubing. Be sure

both ends of copper tubing are cut square.

Using a grounded drill, drill a 1/4in. hole in the cold water pipe

you have selected.

.... !

7 ..... .................

1.Cold waterpipe 5. Compression sleeve

2. Pipe clamp 6. Shutoff valve

3. Copper tubing 7.Packing nut

4. Compression nut

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the 1/4in. drilled hole

in the water pipe and that the washer is under the pipe clamp.

Tighten the packing nut. Tighten the pipe clamp screws

carefully and evenly so washer makes a watertight seal. Do

not overtighten or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and

turn ON the main water supply. Flush the tubing until water is

clear. Turn OFF the shutoff valve on the water pipe. Coil the

copper tubing.

Connecting to Refrigerator

Style 1

1. Unplug refrigerator or disconnect power.

2. Attach the copper tubeto the valve inlet using a compression

nut and sleeve as shown. Tighten the compression nut. Do

not overtighten.

3. Use the tube clamp on the back of the refrigerator to secure

the tubing to the refrigerator as shown. This will help prevent

damage to the tubing when the refrigerator is pushed back

against the wall.

4. Turn shutoff valve ON,

5. Check for leaks, Tighten any connections (including

connections at the valve) or nuts that leak.

Style 3

1. Unplug refrigerator or disconnect power.

2. Remove the shipping tape from the gray, coiled water tubing

on the rear of the refrigerator.

3. Thread the provided nut onto the water valve as shown,

I/ll

1. Tube clamp

2. Copper tubing

3. Compression nut

4. Valve inlet

6. The ice maker is equipped with a built-in water strainer. If

your water conditions require asecond water strainer, install it

in the 1/4in. (6.35 mm) water line at either tube connection,

Obtain a water strainer from your nearest appliance dealer.

7. Plug in refrigerator or reconnect power.

8. Flush the water system. See the "Water System Preparation"

section.

NOTE: Allow 24 hours to produce the first batch of ice. Allow 3

days to completely fill ice container.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove the shipping tape from the gray, coiled water tubing

on the rear of the refrigerator.

3. Thread the provided nut onto the coupling on the end of the

copper tubing. Tighten the nut by hand, Then tighten it with a

wrench two more turns. Do not overtighten.

2 3 4 5 6

1.Line to refrigerator 4. Coupling (purchased)

2. Nut (provided) 5. Ferrule (purchased)

3. Bulb 6. Nut (purchased)

4. Turn shutoff valve ON,

5. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

6. The ice maker is equipped with a built-in water strainer. If

your water conditions require asecond water strainer, install it

in the 1/4in. (6.35 mm) water line at either tube connection,

Obtain a water strainer from your nearest appliance dealer.

7. Plug in refrigerator or reconnect power.

8. Flush the water system. See the "Water System Preparation"

section.

NOTE: Allow 24 hours to produce the first batch of ice. Allow 3

days to completely fill ice container.

1. Bulb

2. Nut (provided)

NOTE: Tighten the nut by hand, Then tighten it with a wrench

two more turns. Do not overtighten,

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

6. The ice maker is equipped with a built-in water strainer. If

your water conditions require a second water strainer, install it

in the 1/4in. (6,35 mm) water line at either tube connection.

Obtain a water strainer from your nearest appliance dealer.

7. Plug in refrigerator or reconnect power.

8. Flush the water system. See the "Water System Preparation"

section,

NOTE: Allow 24 hours to produce the first batch of ice. Allow 3

days to completely fill ice container.

I"RI_II)<] CII Ol

@' @%fl I

Please read before using the water system.

Immediately after installation, follow the steps below to make

sure that the water system is properly cleaned.

1. Open the freezer door and turn off the ice maker by lifting up

the wire shutoff arm as shown.

NOTES:

• If your model has a base grille filter system, make sure the

base grille filter is properly installed and the cap is in the

horizontal position.

• Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system.

Use a sturdy container to depress the water dispenser bar

until the water begins to flow. Flush the water system by

dispensing and discarding 2 to 3 gal. (8 to 12 L) of water.

Cleaning the system will take approximately 6 to 7 minutes

and will help clear air from the line. Additional flushing may be

required in some households•

NOTE: As air is cleared from the system, water may spurt out

of the dispenser•

Open the freezer door and turn on the ice maker by lowering

the wire shutoff arm. Please refer to the "Ice Maker and

Storage Bin" section for further instructions on the operation

of your ice maker•

• Allow 24 hours to produce the first batch of ice.

• Discard the first three batches of ice produced•

• Depending on your model, you may want to select the

maximum ice feature to increase the production of ice. To

do so, set the switch on the front of the ice maker to MAX.

REFRIGERATORUSE

Inorder to ensurepropertemperatures,youneedtopermit to

flow between the two sections• Cold air enters the bottom of the

freezer section and moves up. Itthen enters the refrigerator section

through the top vent. Air then returns to the freezer as shown.

Your new refrigerator may make sounds that your old one didn't

make. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are normal. Hard

surfaces, such as the floor, walls, and cabinets, can make the

sounds seem louder• The following describes the kinds of sounds

and what may be making them.

• If your product is equipped with an ice maker, you will hear a

buzzing sound when the water valve opens to fill the ice

maker for each cycle.

Your refrigerator is designed to run more efficiently to keep

your food items at the desired temperatures and to minimize

energy usage. The high efficiency compressor and fans may

cause your refrigerator to run longer than your old one. You

may also hear a pulsating or high-pitched sound from the

compressor or fans adjusting to optimize performance.

• You may hear the evaporator fan motor circulating air through

the refrigerator and freezer compartments. The fan speed

may increase as you open the doors or add warm food.

• Rattling noises may come from the flow of refrigerant, the

water line, or items stored on top of the refrigerator.

• Water dripping on the defrost heater during a defrost cycle

may cause a sizzling sound.

• As each cycle ends, you may hear a gurgling sound due to

the refrigerant flowing in your refrigerator.

• Contraction and expansion of the inside walls may cause a

popping noise.

• You may hear air being forced over the condenser by the

condenser fan.

• You may hear water running into the drain pan during the

defrost cycle.

Do not block any of these vents with food such as soda, cereal,

bread, etc. If the vents are blocked, airflow will be prevented and

the temperature controls will not function properly.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors• To prevent

odor transfer from food, wrap or cover foods tightly•

For your convenience, your refrigerator controls are preset at the

factory. When installing your refrigerator, make sure that the

controls are still preset to the "mid-settings" as shown.

FREEZER RfFRiGERATOR

I J

, 2 4

COLD COLDER COLD

IMPORTANT:

• 3

1 6 COLDER

Your product will not cool when the Refrigerator Control is set

to OFE

The Refrigerator Control adjusts the refrigerator compartment

temperature. The Freezer Control adjusts the freezer

compartment temperature. Higher numbered settings make

the compartment colder. Lower numbered settings make the

temperature less cold.

• Wait 24 hours before you put food into the refrigerator. If you

add food before the refrigerator has cooled completely, your

food may spoil.

NOTE: Adjusting the Refrigerator and Freezer Controls to a

higher (colder) setting will not cool the compartments any

faster•

• The preset settings should be correct for normal household

usage. The controls are set correctly when milk or juice is as

cold as you like and when ice cream is firm.

• If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not

blocked before adjusting the controls.

Adjusting Controls

If you need to adjust temperatures, adjust the refrigerator

temperature first.

NOTE: Wait at least 24 hours between adjustments and then

recheck the temperatures.

Turn the control right (clockwise) to make the compartment

colder. Turn the control left (counterclockwise) to make it less

cold.

CONDITION/REASON: SETTING

ADJUSTMENT:

REFRIGERATOR too cold REFRIGERATOR

- Not set correctly for your Control one setting

conditions lower

REFRIGERATOR too warm REFRIGERATOR

- Door opened often, large amount Control one setting

of food added or room temperature higher

very warm

FREEZER too cold FREEZER Control one

- Not set correctly for your setting lower

conditions

FREEZER too warm/too little ice FREEZER Control one

- Door opened often, or large setting higher

amount of food added or very cold

room temperature (can't cycle often

enough) or heavy ice usage

Cut Hazard

Use a sturdy gJass when dispensing ice or water.

Faiture to do so can result in cuts.

Depending on your model, you may have one or more of the

following options: the ability to select either crushed or cubed

ice, a special light that turns on when you use the dispenser, or a

lock option to avoid accidental dispensing.

The Ice Dispenser

Ice dispenses from the ice maker storage bin in the freezer. When

the dispenser lever is pressed:

• A trap door opens in a chute between the dispenser and the

ice bin. Ice moves from the bin and falls through the chute.

• When you release the dispenser lever, the trap door closes

and the ice dispensing stops. The dispensing system will not

operate when the freezer door is open.

Some models dispense both cubed and crushed ice. Before

dispensing ice, select which type of ice you prefer. The button

controls are designed for easy use and cleaning.

ICE

CRUSH CUBE

For crushed ice, cubes are crushed before being dispensed. This

may cause a slight delay when dispensing crushed ice. Noise

from the ice crusher is normal, and pieces of ice may vary in size.

When changing from CRUSH to CUBE, a few ounces of crushed

ice will be dispensed along with the first cubes.

To dispense ice:

1. Press button for the desired type of ice.

2. Press a sturdy glass against the ice dispenser lever. Hold the

glass close to the dispenser opening so ice does not fall

outside of the glass.

IMPORTANT: You do not need to apply a lot of pressure to

the lever in order to activate the ice dispenser. Pressing hard

will not make the ice dispense faster or in greater quantities.

Remove the glass to stop dispensing.

NOTE: The first few batches of ice may have an off-flavor

from new plumbing and parts. Throw the ice away. Also, take

large amounts of ice from the ice bin, not through the

dispenser.

The Water Dispenser

If you did not flush the water system when the refrigerator was

first installed, press the water dispenser bar with a glass or jar

until you draw and discard 2to 3 gal. (8 to 12 L) or approximately

6 to 7 minutes of water after water begins dispensing. It will take

3 to 4 minutes for the water to begin dispensing. The water you

draw and discard cleans the system and helps clear air from the

lines. Allow several hours for the refrigerator to cool down and

chill water.

IMPORTANT: Depending on your model, the small removable

tray at the bottom of the dispenser is designed to catch small

spills and allow for easy cleaning. There is no drain in the tray.

The tray can be removed from the dispenser and carried to the

sink to be emptied or cleaned,

To dispense water:

1. Press a glass against the water dispenser lever.

2. Remove the glass to stop dispensing,

NOTE: Water may have an off-flavor if you do not use the

dispenser periodically. Dispense enough water every week to

maintain a fresh supply.

The Dispenser Light

The dispenser area has a light. It can be turned on manually by

pressing the ON button (touchpad or rocker switch).

On some models: Whenever you use the dispenser, the lever will

automatically turn the light on.

LIGHT

OFF ON

NOTE: See the "Changing the Light Bulbs" section for

information on changing the dispenser light bulb.

The Dispenser Lock (on some models}

Your dispenser can be turned off for easy cleaning or to prevent

accidental dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the product,

to the ice maker, or to the dispenser light. It simply deactivates

the dispenser levers.

To turn off the dispenser, press the LOCK button. The indicator

will appear above the LOCK button and the ice and water

dispensers will not work. To unlock the dispenser, press the

UNLOCK button until the indicator appears. Then continue to

dispense ice or water as usual.

DISPENSER

LOCK UNLOCK

The water filter status light will help you know when to change

your water filter cartridge. The light is located at the top of the

refrigerator compartment. The light will change from green to

yellow. This tells you that it is almost time to change the water

filter cartridge (90% of the filter life has been used). It is

recommended that you replace the base grille water filter

cartridge when the water filter indicator light changes to red OR

water flow to your water dispenser or ice maker decreases

noticeably. See "Changing the Water Filter Cartridge" later in this

section.

After changing the water filter cartridge, reset the water filter

status light by pressing the light switch 5 times within 10

seconds. The indicator light will change from red to green when

the system is reset.

......................................2

1. Status light

2. Light switch

Non-indicator Water Filter (on some models)

If your refrigerator does not have the water filter status light, you

should change the water filter cartridge every 6 to 9 months

depending upon your usage. If the water flow to the water

dispenser or ice maker decreases noticeably before 6 months

have passed, replace the water filter cartridge more often.

NOTE: Do not use with water that is microbiologically unsafe

or of unknown quality without adequate disinfection before

or after the system.

Changing the Water Filter Cartridge

The base grille water filter is located below the freezer

compartment door. Depending on your model, you may have a

filter that is installed behind the base grille (Style 1) or a filter that

is installed through the base grille (Style 2).

Style 1: Behind the base grille filter

1. Remove the base grille (see "Door Removal" section). Rotate

the cartridge counterclockwise to a vertical position and pull

the filter cartridge out.

NOTE: There will be water in the cartridge. Some spilling may

occur.

Take the new cartridge out of its packaging and remove

protective cover from o-rings.

Push the new filter cartridge into the base until it stops.

Rotate the cartridge clockwise to a horizontal position. Flush

the water system (see "Flushing the Water System After

Replacing Filter" later in this section).

Style 2: Through the base grille filter

1. Locate the water filter cartridge cap in the front base grille.

Rotate the cap counterclockwise to a vertical position and

pull the cap and filter cartridge out through the base grille.

NOTE: There will be water in the cartridge. Some spilling may

occur.

2. Remove the cartridge cap by sliding it off the end of the old

cartridge. The cap will slide to the left or right. DO NOT

DISCARD THE CAR

3. Take the new cartridge out of its packaging and remove

protective cover from o-rings.

4. Slide the cartridge cap onto the new cartridge. See

illustration in Step 2.

With cartridge cap in the vertical position, push the new filter

cartridge into the base grille until it stops. Rotate the cartridge

cap clockwise to a horizontal position. Flush the water

system (see "Flushing the Water System After Replacing

Filter" later in this section).

Flushing the Water System After Replacing Filter

Use a sturdy container to depress the water dispenser bar until

the water begins to flow. Flush the water system by dispensing

and discarding 2 to 3 gal. (8 to 12 L) of water. Cleaning the

system will take approximately 6 to 7 minutes and will help clear

air from the line. Additional flushing may be required in some

households.

NOTE: As air is cleared from the system, water may spurt out of

the dispenser.

Using the Dispenser Without the Water Filter

You can run the dispenser without a water filter cartridge. Your

water will not be filtered.

1. Remove the base grille water filter cartridge. For Style 1,

replace the base grille after removing the filter.

2. For Style 2, slide the cartridge cap off the end of the filter

cartridge. DO NOT DISCARD THE CAR With the cartridge

cap in the vertical position, insert the cap into the base grille

until it stops.

Rotate the cartridge cap to a horizontal position. The

cartridge cap might not be even with the base grille.

To turn the ice maker on/off:

The on/off switch for the ice maker is a wire shutoff arm located

on the side of the ice maken

1. Toturn the ice maker on, simply lower the wire shutoff arm.

NOTE: Your ice maker has an automatic shutoff. As ice is

made, the ice cubes will fill the ice storage bin and the ice

cubes will raise the wire shutoff arm to the OFF (arm up)

position.

2. To manually turn the ice maker off, lift the wire shutoff arm to

the OFF (arm up) position and listen for the click to make sure

the ice maker will not continue to operate.

increase ice production rate:

Normal Ice Production: In normal ice production mode, the

ice maker should produce approximately 7 to 9 batches of ice

in a 24-hour period. If ice is not being made fast enough, turn

the Freezer Control toward a higher (colder) number in half

number steps. (For example, if the control is at 3, move it to

between 3 and 4.) Wait 24 hours between each increase.

Maximum Ice Production (on some models): In maximum ice

production, the ice maker should produce approximately 10

to 14 batches of ice in a 24-hour period. If your refrigerator

has the maximum ice production feature, push the switch

to MAX.

To remove and replace the ice bin:

1. Pull the covering panel out from the bottom and then slide it

back toward the rear.

2. Lift the wire shutoff arm so it clicks into the OFF (up) position.

Ice can still be dispensed, but no more can be made.

3. Lift up the front of the storage bin and pull it out.

4. Replace the bin by pushing it in all the way or the dispenser

will not work. Push the wire shutoff arm down to the ON

position to restart ice production. Make sure the door is

closed tightly.

Clean the Ice Storage Bin

Empty the ice bin. Use warm water to melt the ice if

necessary.

NOTE: Never use anything sharp to break up the ice in the

bin. This can cause damage to the ice container and the

dispenser mechanism.

2. Wash ice bin with a mild detergent, rinse well and dry

thoroughly. Do not use harsh or abrasive cleaners or solvents.

REMEMBER

• Allow 24 hours to produce the first batch of ice.

• Discard the first three batches of ice produced to avoid

impurities that may be flushed out of the system.

• The quality of your ice will be only as good as the quality of

the water supplied to your ice maker.

Avoid connecting the ice maker to a softened water supply.

Water softener chemicals (such as salt) can damage parts of

the ice maker and lead to poor quality ice. If a softened water

supply cannot be avoided, make sure the water softener is

operating properly and is well maintained.

• It is normal for the ice cubes to be attached at the corners.

They will break apart easily.

• Do not force the wire shutoff arm up or down.

• Do not store anything on top of the ice maker or in the ice

storage bin.

REFRIGERATORFEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word "Accessory." Not all accessories will fit all models.

If you are interested in purchasing one of the accessories, please

call the toll-free number on the cover or in the "Accessories"

section.

_mportant information to know about glass sheBves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass

shelves and covers are heavy. Use special care when re-

moving them to avoid impact from dropping.

To raise or lower the shelf:

1. Raise the shelf by pulling forward on the lever located at the

bottom front of the shelf and lift until the shelf locks into the

vertical position.

2. Lower the shelf until it is latched securely in place.

Your model may have glass or wire shelves. Store similar foods

together and adjust the shelves to fit different heights. This 1.

reduces the time the refrigerator door is open and saves energy.

Slide-out Shelves (on some models} 2.

To remove and replace a shelf in a metal frame:

1. Pull the shelf forward to the stop. Tilt the front of the shelf up

and lift it slightly as you pull the shelf from the frame.

2. Replace the shelf by guiding it back into the slots on the

frame and pushing the shelf in past the stop.

To raise or lower the shelf:

Raise the shelf by first sliding it back and down to make it

half-width. (You can use the shelf in this position to allow

taller items to be stored on the shelf below.)

Lift the front of the shelf until it fits securely in place against

the back wall. Lower the shelf securely back into position.

3. Pull the front of the shelf forward until it fits into place.

Shelves and Shelf Frames

To remove and replace a shelf/frame:

1. Remove the shelf/frame by tilting it up at the front and lifting it

out of the shelf supports.

2. Replace the shelf/frame by guiding the rear shelf hooks into

the shelf supports. Tilt the front of the shelf up until rear shelf

hooks drop into the shelf supports. Check to make sure that

the shelf is securely in position.

The dell drawer stores raisins, nuts, spreads, and other small

items at normal refrigerator temperatures.

To remove and replace the dell drawer:

1. Remove the dell drawer by sliding it straight out to the stop.

Lift the front and slide the drawer out the rest of the way.

2. Replace the dell drawer by sliding it back past the stop.

Crisper and Convertible Vegetable Meat Drawers

To remove and replace drawers:

1. Slide crisper or meat drawer straight out to the stop. Lift the

front of drawer with one hand while supporting the bottom of

drawer with other hand and slide the drawer out the rest of

the way.

2. Replace the crisper or meat drawer by sliding it back in fully

past the drawer stop.

Crisper or Vegetable/Meat Drawer Covers

To remove and replace covers:

1. Remove the crisper and meat drawer. Press up in center of

crisper glass insert until it rises above the plastic frame.

Holding the crisper glass firmly, carefully slide the glass insert

forward to remove.

2. Lift crisper cover frame and remove. Repeat steps to remove

the meat drawer cover.

3. Replace back of meat drawer cover frame into supports or

slides on side walls of the refrigerator and lower or slide the

front of the cover frame into place.

4. Slide rear of glass insert into cover frame and lower front into

place. Repeat steps to replace the crisper cover.

The convertible vegetable/meat drawer can be adjusted to

properly chill meats or vegetables. The air inside the pan is

cooled to prevent "spot" freezing and can be set to keep meats

at the National Livestock and Meat Board recommended storage

temperatures of 28°- 32°F (-2°- 0°C).

IMPORTANT: To extend freshness, wrap meats in airtight,

moisture-proof materials before storing. Always store meat as

recommended.

Adjusting the Control

The convertible control comes preset at the lowest meat setting.

To change a control setting: Move the control to the right

(colder) or to the left (less cold) as desired.

To store vegetables: Set the control to VEG (all the way to the

left) to store vegetables at their optimal storage temperatures

(which need to be warmer than those for meat).

IMPORTANT: If food starts to freeze, move the control to the left

(less cold). Remember to wait 24 hours between adjustments.

Doing so gives the temperature of the food time to change.

Meat Storage Guide

Store most meat in original wrapping as long as it is airtight and

moisture-proof. Rewrap if necessary. See the following chart for

storage times. When storing meat longer than the times given,

freeze the meat.

Fresh fish or shellfish ......................... use same day as purchased

Chicken, ground beef, variety meat (liver, etc.) ................ 1-2 days

Cold cuts, steaks/roasts .................................................. 3-5 days

Cured meats ................................................................... 7-10 days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or

plastic containers with tight lids.

You can control the amount of humidity in the moisture-sealed

crisper. Adjust the control to any setting between LOW and

HIGH.

LOW (open) lets moist air out of the crisper for best storage of

fruits and vegetables with skins.

• Fruit: Wash, let dry and store in refrigerator in plastic bag or

crisper. Do not wash or hull berries until they are ready to use.

Sort and keep berries in original container in crisper, or store

in a loosely closed paper bag on a refrigerator shelf.

• Vegetables with skins: Place in plastic bag or plastic

container and store in crisper.

HIGH (closed) keeps moist air in the crisper for best storage of

fresh, leafy vegetables.

• Leafy vegetables: Wash in cold water, drain and trim or tear

off bruised and discolored areas. Place in plastic bag or

plastic container and store in crisper.

Humidity control location:

• Humidity Control on crisper drawer (Style 1 - on left)

Humidity Control on crisper cover (Style 2 - on right)

I__1 High 5 4 3 2 1 l.OW

@ O, ........ul%, B.S ..........+.

{iO£q_OO'%¢;:._:s 'w'_:_:@,oA "o,'-¢;s,q_OK'v%

To remove and replace the wine rack (left) or can/bottle

rack (right):

1. Remove the rack by pulling it straight out from the shelf.

2. Replace the rack by sliding it in between the shelf and the

wall of the refrigerator.

(on some Y"odeB - Acc_ sso_y}

NOTI:: For long-term storage, place eggs in a covered container

or in their original carton on an interior shelf.

FREEZERFEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word "Accessory." Not all accessories will fit all models.

If you are interested in purchasing one of the accessories, please

call the toll-free number on the cover or in the "Accessories"

section.

To remove and replace the shelf:

1. Lift the shelf off of the supports.

2. Slide it out of the shelf support holes.

3. Replace shelf in the reverse order.

Frozen Food Storage Guide

Storage times will vary according to the quality and type of food,

the type of packaging or wrap used (should be airtight and

moisture-proof), and the storage temperature. Ice crystals inside

a sealed package are normal. This simply means that moisture in

the food and air inside the package have condensed, creating ice

crystals.

Put no more unfrozen food into the freezer than will freeze within

24 hours (no more than 2 to 3 Ibs. of food per cubic foot

[907-1,350 g per L] of freezer space). Leave enough space in the

freezer for air to circulate around packages. Be careful to leave

enough room for the door to close tightly.

For more information on preparing food for freezing, check a

freezer guide or reliable cookbook.

F Bn

The freezer basket or bin can be used to store bags of frozen

fruits and vegetables that may slide off freezer shelves.

To remove and replace the freezer basket or bin:

1. Remove basket or bin by sliding it out to the stop.

2. Lift the front of the basket or bin and slide it out the rest of the

way.

Replace the basket or bin by positioning it on the side wall

guide rails. Lift the basket or bin front slightly while pushing it

past the guide rail stops and slide basket or bin in the rest of

the way.

DOOR FEATURES

Your model may have some or all of these features. Features that

can be purchased separately as product accessories are labeled

with the word "Accessory." Not all accessories will fit all models.

If you are interested in purchasing one of the accessories, please

call the toll-free number on the cover or in the "Accessories"

section.

The door rails may be removed for easier cleaning.

Snap-on Door Rails

To remove and replace the rails:

1. Remove the rails by pushing in slightly on the front of the

bracket while pulling out on the inside tab. Repeat these

steps for the other end of the rail.

2. Replace the rails by aligning the ends of the brackets with the

buttons on the sides of the door liner. Firmly snap bracket

and rail assembly onto the tabs above the shelf as shown.

Drop-in Door Rails

To remove and replace the rails:

1. Remove the rails by pulling straight up on each end of the rail.

2. Replace the rails by sliding the shelf rail into the slots on the

door and pushing the rail straight down until it stops.

@sd ©00 BF S

NOTE: Can racks may be purchased as an Accessory for some

models.

To remove and replace the racks/bins:

1. Remove the rack/bin by lifting it and pulling it straight out.

2. Replace the racWbin by sliding it in above the desired

support and pushing it down until it stops.

REFRIGERATORCARE

Explosion Hazard

Use nonflammable cJeaner.

Failure to do so can resuJt in death, explosion,

or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to prevent

odors from building up. Wipe up spills immediately.

Cleaning your refrigerator

1. Unplug refrigerator or disconnect power.

2. Remove all removable parts from inside, such as shelves,

crispers, etc.

3. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

• Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning

waxes, concentrated detergents, bleaches or cleansers

containing petroleum products on plastic parts, interior

and door liners or gaskets. Do not use paper towels,

scouring pads, or other harsh cleaning tools. These can

scratch or damage materials.

• To help remove odors, you can wash interior walls with a

mixture of warm water and baking soda (2 tbs. to 1 qt.

[26 g to.95 L] of water).

4. Determine whether your refrigerator exterior is painted metal,

brushed aluminum or stainless steel and choose the

appropriate cleaning method.

Painted metal: Wash exteriors with a clean sponge or soft

cloth and a mild detergent in warm water. Do not use abrasive

or harsh cleaners, or cleaners designed for stainless steel.

Dry thoroughly with a soft cloth. For additional protection

against damage to painted metal exteriors, apply appliance

wax (or auto paste wax) with a clean, soft cloth. Do not wax

plastic parts.

Brushed Aluminum: Wash with a clean sponge or soft cloth

and a mild detergent in warm water. Do not use abrasive or

harsh cleaners, or cleaners designed for stainless steel. Dry

thoroughly with a soft cloth.

Stainless steel finish: Wash with a clean sponge or soft

cloth and a mild detergent in warm water. Do not use abrasive

or harsh cleaners, or cleaners designed for stainless steel.

Dry thoroughly with a soft cloth.

To keep your Stainless Steel refrigerator looking like new

and to remove minor scuffs or marks, it is suggested that

you use the manufacturer's approved Stainless Steel

Cleaner & Polish.

Do not allow the Stainless Steel Cleaner & Polish to come into

contact with any plastic parts such as the trim pieces,

dispenser covers or door gaskets. If accidental contact does

occur, clean plastic part with a sponge and mild detergent in

warm water. Dry thoroughly with a soft cloth. To order the

cleaner, see the "Accessories" section.

There is no need for routine condenser cleaning in normal

home operating environments. If the environment is

particularly greasy or dusty, or there is significant pet traffic in

the home, the condenser should be cleaned every 2 to 3

months to ensure maximum efficiency.

If you need to clean the condenser:

• Remove the base grille. See "Base Grille" or "Door

Removal" section.

• Use a vacuum cleaner with a soft brush to clean the grille,

the open areas behind the grille and the front surface area

of the condenser.

• Replace the base grille when finished.

Plug in refrigerator or reconnect power.

NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to

replace the bulb with one of the same size and shape, The

dispenser light requires a heavy duty 10-watt bulb. All other lights

require a 40-watt appliance bulb. Replacement bulbs are

available from your dealer.

1. Unplug refrigerator or disconnect power.

2. Remove light shield when applicable as shown.

NOTE: To clean the light shield, wash it with warm water and

liquid detergent. Rinse and dry the shield well.

3. Remove light bulb and replace with one of the same size,

shape and wattage.

4. Replace light shield when applicable as shown.

5. Plug in refrigerator or reconnect power.

Dispenser Light (on some models)

Reach through the dispenser area to remove and replace

light bulb.

1.Dispenser light

Refrigerator Control Panel Light

Reach behind the refrigerator control panel to remove and

replace light bulb.

IMPORTANT: This cleaner is for Stainless Steel parts only!

CrisperLights

• If necessary, remove the top crisper drawer to access the

crisper light shield. Remove the light shield by lifting the ends

out of the brackets as shown.

• Replace the light shield by inserting the ends into the

brackets. If necessary, replace the top crisper drawer.

Style 2 - Behind Freezer Basket

• Depending on your model, remove the top freezer basket or

top freezer basket shelf. Remove light shield by removing the

Phillips screw on the top of the shield. Carefully rotate the

shield until the left tab can be gently pulled from the freezer

waU.

• Replace the light shield by inserting the left tab into the

freezer wall. Align top tab with screw hole and replace screw.

Upper Freezer Light (on some models)

Style 1

• Remove light shield by grasping the top center of the shield

and pulling forward while turning it slightly to one side. If

necessary, remove top crisper drawer to gain access to the

crisper light shield.

Replace the light shield by inserting the tabs on one end into

the slotted holes in the refrigerator or freezer liner. Then,

carefully bend the shield at the center to insert the tabs on the

other end.

Style 2

• Remove the light shield by squeezing the sides of the light

shield in toward the center while pulling the shield forward as

shown.

Replace the light shield by fitting the tabs into the slotted

holes in the freezer liner. Push in the shield until it snaps into

place.

Lower Freezer Light (on some models)

Style I - Beneath Ice Bin

• Remove the light shield by grasping the sides and squeezing

in toward the center. Once the side hooks of shield are free

from the freezer lining, pull down the shield.

Replace the light shield by squeezing the sides toward the

center and inserting the side hooks into the slotted holes.

Once the side hooks are in place, snap the front tab into the

slotted hole.

If the power will be out for 24 hours or less, keep both refrigerator

doors closed to help food stay cold and frozen.

If the power will be out for more than 24 hours, do one of the

following:

• Remove all frozen food and store it in a frozen food locker.

• Place 2 Ibs (907 g) of dry ice in the freezer for every cubic foot

(28 L) of freezer space. This will keep the food frozen for 2 to

4 days.

• If neither afood locker nor dry ice is available, consume or

can perishable food at once.

REMEMBER: A full freezer stays cold longer than a partially filled

one. A freezer full of meat stays cold longer than a freezer full of

baked goods. If you see that food contains ice crystals, it may be

refrozen, although the quality and flavor may be affected. If the

condition of the food is poor, dispose of it.

Vacations

If you choose to leave the refrigerator on while you're

away:

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker:

• Raise wire shutoff arm to OFF (up) position or move the

switch to the OFF (right) setting.

• Shut off water supply to the ice maker.

3. Empty the ice bin.

If you choose to turn the refrigerator off before you leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or move the switch to the OFF

(right) setting.

3. Depending on your model, turn the Thermostat Control or

Refrigerator Control to OFF. See the "Using the Controls"

section.

4. Clean refrigerator, wipe it, and dry well.

5. Tape rubber or wood blocks to the tops of both doors to prop

them open far enough for air to get in. This stops odor and

mold from building up.

Moving

When you are moving your refrigerator to a new home, follow

these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• Disconnect the water line from the back of the

refrigerator.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or move the switch to the OFF

(right) setting.

2. Remove all food from the refrigerator and pack all frozen food

in dry ice.

3. Empty the ice bin.

4. Depending on your model, turn the Thermostat Control or

Refrigerator Control to OFE See the "Using the Controls"

section.

5. Unplug refrigerator.

6. Empty water from the defrost pan.

7. Clean, wipe, and dry thoroughly.

8. Take out all removable parts, wrap them well, and tape them

together so they don't shift and rattle during the move.

9. Depending on the model, raise the front of the refrigerator so

it rolls more easily OR screw in the leveling legs so they don't

scrape the floor. See the "Door Closing" or "Leveling Your

Refrigerator" section.

10. Tape the doors closed and tape the power cord to the

refrigerator cabinet.

When you get to your new home, put everything back and refer to

the "Installation Instructions" section for preparation instructions.

Also, if your refrigerator has an automatic ice maker, remember to

reconnect the water supply to the refrigerator.

UBLESHOOTING

Trythe solutions suggested here first in order to avoid the

cost of an unnecessary service call.

Your refrigerator will not operate

• Is the power supply cord unplugged? Plug into a grounded

3 prong outlet.

Has a household fuse or circuit breaker tripped? Replace

the fuse or reset the circuit breaker.

Is the refrigerator or freezer control turned to the OFF

position? See "Using the Controls."

msthe refrigerator defrosting? Recheck to see whether the

refrigerator is operating in 30 minutes. Your refrigerator will

regularly run an automatic defrost cycle.

Is the refrigerator not cooling? For models with digital

controls, turn the unit OFF then ON again to reset. See "Using

the Controls." If this does not correct the problem, call for

service.

The lights do not work

• Is the power supply cord unplugged? Plug into a grounded

3 prong outlet.

• Is a light bulb loose in the socket or burned out? See

"Changing the Light Bulbs."

There is water in the defrost drain pan

• Is the refrigerator defrosting? The water will evaporate. It is

normal for water to drip into the defrost pan.

• is it more humid than normal? When it is humid, expect that

the water in the defrost pan will take longer to evaporate.

The motor seems to runtoo much

Is the room temperature hotter than normal? The motor

will run longer under warm conditions. At normal room

temperatures, expect your motor to run about 40% to 80% of

the time. Under warmer conditions, it will run even more.

Has a large amount of food just been added to the

refrigerator? Adding a large amount of food warms the

refrigerator. The motor normally will run longer to cool the

refrigerator back down.

Are the doors opened often? The motor will run longer

when this occurs. Conserve energy by getting all items out at

one time, keeping food organized, and closing the door as

soon as possible.

Are the controls not set correctly for the surrounding

conditions? See "Using the Controls."

Are the doors not closed completely? Close the doors

firmly. If they do not close completely, see "The doors will not

close completely" later in this section.

Are the condenser coils dirty? This prevents air transfer and

makes the motor work harder. Clean the condenser coils. See

"Cleaning."

Are the door gaskets not sealed all the way around?

Contact a technician or other qualified person.

NOTE: Your new refrigerator will run longer than your old one

due to its high-efficiency motor.

The refrigerator seems to make too much noise

• The sounds may be normal for your refrigerator. See "Normal

Sounds."

The ice maker is not producing ice or not enough ice

• Has the ice maker just been installed? Wait 72 hours for full

ice production to begin. Once your refrigerator is cooled, the

ice maker should produce 70 to 120 cubes every 24 hours.

Is the freezer temperature cold enough to produce ice?

Wait 24 hours after ice maker hookup for ice production. See

"Using the Controls."

Is the ice maker wire shutoff arm in the OFF (arm up)

position (on some models)? Lower the wire shutoff arm to

the ON (arm down) position. See "Ice Maker and Storage

Bin."

Is the ice maker switch in the OFF (right) position (on

some models)? Move ice maker switch to the ON (left)

position. See "Ice Maker and Storage Bin."

Is the water line shutoff valve to the refrigerator turned

on? Turn on the water valve. See "Water Supply Connection."

Does the ice maker mold have water in it or has no ice

been produced? Make sure your refrigerator has been

connected to a water supply and the supply shutoff valve is

turned on. See "Water Supply Connection."

Is an ice cube jammed in the ice maker ejector arm?

For models with a standard ice storage bin, remove the ice

from the ejector arm with a plastic utensil. For models with an

ice storage bin on the freezer door, access the ice maker by

depressing the ice sensor door on the upper left side of the

freezer interior. While depressing the sensor door, lift the ice

maker service door and remove the ice from the ejector with

a plastic utensil. See "Ice Maker and Storage Bin."

• Has a large amount of ice just been removed? Allow 24

hours for ice maker to produce more ice.

• Are the controls set correctly? See "Using the Controls."

Is there a water filter installed on the refrigerator? The

filter may be clogged or installed incorrectly. Check the filter

installation instructions to ensure that the filter was installed

correctly and is not clogged. If installation or clogging is not a

problem, call a technician or other qualified person.

• Is a reverse osmosis water filtration system connected to

your cold water supply? See "Water Supply Requirements."

NOTE: If not due to any of the above, there may be a problem

with the water line. Call for service.

Off-taste, odor or gray color inthe ice

• Are the plumbing connections new, causing discolored or

off-flavored ice? Discard the first few batches of ice.

• Have the ice cubes been stored too long? Throw old ice

away and make a new supply.

• Does the freezer and ice storage bin need to be cleaned?

See "Cleaning" or "Ice Maker and Storage Bin."

• Has food in the freezer or refrigerator been wrapped

properly? Use airtight, moisture-proof packaging to help

prevent odor transfer to stored food.

• Does the water contain minerals (such as sulfur)? A filter

may need to be installed to remove the minerals.

Is there a water filter installed on the refrigerator? Gray or

dark discoloration in ice indicates that the water filtration

system needs additional flushing. Run additional water

through the water dispenser to flush the water filtration

system more thoroughly (at least 2 to 3 gal. [8 to 12 L] or 6 to

7 minutes initially). Discard discolored ice.

The ice dispenser will not operate properly

• Is the freezer door closed completely? Push the door firmly

closed. If it will not close all the way, see "The doors will not

close completely" later in this section.

Is the ice storage bin installed correctly? For models with a

standard ice storage bin, push the ice storage bin in all the

way. For models with an ice storage bin on the freezer door,

the bin should sit level. Remove and replace the bin in the

door making sure it is properly aligned and snapped securely

into place. See "Ice Maker and Storage Bin."

Has the wrong ice been added to the bin? Use only cubes

produced by the current ice maker. If other cubes have been

added, remove all cubes and check to see that none have

become stuck in the delivery chute.

• Has the ice frozen in the ice storage bin? Shake the ice

storage bin to separate cubes. If cubes do not separate,

empty bin and wait 24 hours for ice to restock.

Has the ice melted around the auger (metal spiral) in the

ice storage bin? Dump the ice cubes and clean the ice

storage bin completely. Allow 24 hours for the ice maker to

restock. Do not try to remove the melted ice with a sharp

object. You could damage the ice storage bin.

• Is ice stuck in the delivery chute? Clear the ice from the

delivery chute with a plastic utensil. Do not use anything

sharp to remove the ice. You could cause damage.

Is the ice dispenser stalling while dispensing "crushed"

ice? Stop dispensing ice. Change the ice button from

"crushed" to "cubed." Depress the ice dispenser arm using a

sturdy glass. If cubed ice dispenses correctly, depress the

button for "crushed" ice and begin dispensing again. See

"Water and Ice Dispensers."

• Is there ice in the storage bin? See "The ice maker is not

producing ice" earlier in this section.

Has the dispenser arm been held in too long? Release

dispenser arm. Ice will stop dispensing when the arm is held

in too long. Wait 3 minutes for dispenser motor to reset

before using again. It is best to take large amounts of ice

directly from the ice storage bin, not through the dispenser.

Ice storage bin difficult to remove

Is the ice storage bin difficult to remove (on some

models)? For models with an ice storage bin located on the

freezer door, select "cubed" ice. Using a sturdy glass, quickly

depress and release the ice dispenser arm. Open the freezer

door, depress the release button on the ice storage bin and

lift upward. See "Ice Maker and Storage Bin."

The water dispenser will not operate properly

Has the water system not filled? The water system needs

to be filled the first time it is used. Use a sturdy container to

depress the water dispenser bar until the water begins to

flow. Flush the water system by dispensing and discarding

2 to 3 gal. (8 to 12 L) of water. Cleaning the system will take

approximately 6 to 7 minutes and will help clear air from the

line. Additional flushing may be required in some households.

See "Water and Ice Dispensers."

Is the water shutoff valve not turned on or the water line

connected at the source? Make sure the water shutoff valve

is turned on and the water source is connected to the

refrigerator. See "Water Supply Connection."

• Is the water shutoff valve clogged or incorrectly installed?

See "Water Supply Connection." If clogging or installation is

not a problem, call for service or contact a plumber.

• Is there a kink in the home water source line? Ifyou find or

suspect a kink in the water line, contact a licensed, qualified

plumber.

Is there a water filter installed on the refrigerator? The

filter may be clogged or incorrectly installed. First, check the

filter installation instructions to ensure that the filter was

installed correctly and is not clogged. If installation or

clogging is not a problem, call for service.

• Is a reverse osmosis water filtration system connected to

your cold water supply? See "Water Supply Requirements."

Water or ice isleaking from the dispenser

Is the glass not being held under the ice dispenser long

enough, causing the ice to spill? Hold the container under

the ice chute for 2 to 3 seconds after releasing the dispenser

lever. Water or ice may continue to dispense during this time.

• Is an ice cube stuck in the chute and holding the trap

door open? Remove the cube.

La page charge ...

Roper RS25AFXRD01 Le manuel du propriétaire

Marque: Roper

Modèle: RS25AFXRD01

Catégorie: Frigos

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Roper RS25AFXRD01 Owner's manual

Documents connexes

Roper TOP-MOUNT REFRIGERATOR Le manuel du propriétaire

Roper RS25AFXRD01 Le manuel du propriétaire

Roper RS25AFXRD01 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents