Stanley SFMCCS630 Le manuel du propriétaire

SFMCCS630

Final page size: A5 (148mm x 210mm)

www.stanleytools.eu

B

Copyright STANLEYFATMAX

English (original instructions) 4

Deutsch (übersetzt von den originalanweisungen) 18

Français (traduction de la notice d’instructions originale) 35

Italiano (tradotto dalle istruzioni originali) 52

Nederlands (vertaald vanuit de originele instructies) 68

Español (traducido de las instrucciones originales) 84

Português (traduzido das instruções originais) 100

Svenska (översatt från de ursprungliga instruktionerna) 116

Norsk (oversatt fra de originale instruksjonene) 131

Dansk (oversat fra original brugsvejledning) 145

Suomi (käännetty alkuperäisestä käyttöohjeesta) 160

Ελληνικά (μετάφραση από τις πρωτότυπες οδηγίες) 174

1

Fig. A

7

2

1

3

4

5

6

8

9

10

11

12

13

14

15

16

Fig. C

6

8

Fig. D

18

20

19

17

Fig. B

14

15

2

Fig. E Fig. F

9

8

6

Fig. G

Fig. H

16

10

Fig. I

11

Fig. J

12

13

Fig.K

3

13

Fig. L

1

2

3

Fig. M

Fig. N

Fig. O Fig. P

Fig. Q

60°

21

0.635mm

4

ENGLISH

“X” Indicates that the battery pack is compatible with that

specific charger. Read the instruction manual for more

specificinformation.

EC-Declaration of Conformity

Machinery Directive

18V Chainsaw

SFMCCS630

STANLEYFATMAX declares that these products described under

Technical Data are in compliance with:

2006/42/EC, EN60745-1:2009+A11:2010, EN60745-2-

13:2009+A1:2010.

2000/14/EC , Annex V DEKRA Certification B.V., Meander 1051 /

P.O. Box 5185 6825 MJ ARNHEM / 6802 ED

ARNHEM

Netherlands

Notified Body ID No.: 0344

L

PA

(measured sound pressure level) 86 dB(A)

uncertainty K = 1,6 dB(A)

L

WA

(guaranteed sound power) 100 dB(A)

These products also comply with Directive 2014/30/

EU, 2011/65/EU. For more information, please contact

STANLEYFATMAX at the following address or refer to the back

of themanual.

The undersigned is responsible for compilation of the technical

file and makes this declaration on behalf ofSTANLEYFATMAX.

A. P. Smith

Technical Director

STANLEYFATMAX Europe, Egide Walschaertsstraat14-18,

2800 Mechelen, Belgium

2019-10-11

WARNING: To reduce the risk of injury, read the

instructionmanual.

Definitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to

thesesymbols.



DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death or

seriousinjury.



WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or

seriousinjury.

Congratulations!

You have chosen a STANLEYFATMAX tool. Years of experience,

thorough product development and innovation make

STANLEYFATMAX one of the most reliable partners for

professional power toolusers.

Technical Data

SFMCCS630

Voltage V

DC

18

Battery type Li-Ion

Type 1

Bar Length cm 30

Maximum Chain Speed (no-load) m/s 7.7

Maximum Cutting Length cm 25

Oil Capacity ml 230

Weight (without battery pack) kg 3.86

Noise values and vibration values (triax vector sum) according to EN60745-2-13.

L

PA

(emission sound pressure level) dB(A) 86

L

WA

(sound power level) dB(A) 98

K (uncertainty for the given sound level) dB(A) 1,6

Vibration emission value a

h

= m/s

2

3.9

Uncertainty K = m/s

2

1.5

The vibration emission level given in this information sheet has

been measured in accordance with a standardised test given in

EN60745 and may be used to compare one tool with another. It

may be used for a preliminary assessment ofexposure.



WARNING: The declared vibration emission level

represents the main applications of the tool. However if

the tool is used for different applications, with different

accessories or poorly maintained, the vibration emission

may differ. This may significantly increase the exposure

level over the total workingperiod.

An estimation of the level of exposure to vibration should

also take into account the times when the tool is switched

off or when it is running but not actually doing the job.

This may significantly reduce the exposure level over the

total workingperiod.

Identify additional safety measures to protect the operator

from the effects of vibration such as: maintain the tool

and the accessories, keep the hands warm, organisation

of workpatterns.

Battery

Cat #

Output

Voltage

Charger

SFMCB12

SFMCB202 18 X

SFMCB204 18 X

SFMCB206 18 X

English (original instructions)

30 CM 18V CHAINSAW

SFMCCS630

5

ENGLISH



CAUTION: Indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderateinjury.

NOTICE: Indicates a practice not related to

personal injury which, if not avoided, may result in

propertydamage.



Denotes risk of electricshock.



Denotes risk offire.

General Power Tool Safety Warnings



WARNING: Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

powertool.

1) Work area safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which

may ignite the dust orfumes.

c ) Keep children and bystanders away while operating

a power tool. Distractions can cause you to losecontrol.

2) Electrical safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of

electricshock.

b ) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if

your body is earthed orgrounded.

c ) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electricshock.

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electricshock.

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electricshock.

f ) If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electricshock.

3) Personal safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use a power tool while you are tired or under the

influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in

serious personalinjury.

b ) Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection used

for appropriate conditions will reduce personalinjuries.

c ) Prevent unintentional starting. Ensure the switch

is in the off position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energising power tools that have the switch on

invitesaccidents.

d ) Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached

to a rotating part of the power tool may result in

personalinjury.

e ) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair

can be caught in movingparts.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-relatedhazards.

4) Power tool use and care

a ) Do not force the power tool. Use the correct power

tool for your application. The correct power tool

will do the job better and safer at the rate for which it

wasdesigned.

b ) Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must berepaired.

c ) Disconnect the plug from the power source and/or

the battery pack from the power tool before making

any adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce the

risk of starting the power toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrainedusers.

e ) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

Batteries

Chargers/Charge Times (Minutes)

Cat #

DC

Weight

6

ENGLISH

before use. Many accidents are caused by poorly

maintained powertools.

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits etc.,

in accordance with these instructions taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardoussituation.

5) Battery tool use and care

a ) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with

another batterypack.

b ) Use power tools only with specifically designated

battery packs. Use of any other battery packs may create

a risk of injury andfire.

c ) When battery pack is not in use, keep it away from

other metal objects like paper clips, coins, keys,

nails, screws or other small metal objects that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause burns

or afire.

d ) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation orburns.

6) Service

a ) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool ismaintained.

Additional Chainsaw Safety Warnings



WARNING: Additional safety warnings

forchainsaws.

• Keep all parts of the body away from the saw chain

when the chain saw is operating. Before you start the

chain saw, make sure the saw chain is not contacting

anything. A moment of inattention while operating chain

saws may cause entanglement of your clothing or body with

the sawchain.

• Always hold the chain saw with your right hand on the

rear handle and your left hand on the front handle.

Holding the chain saw with a reversed hand configuration

increases the risk of personal injury and should never bedone.

• Hold the power tool by insulated gripping surfaces only,

because the saw chain may contact hidden wiring. Saw

chains contacting a "live" wire may make exposed metal

parts of the power tool "live" and could give the operator an

electricshock.

• Wear safety glasses and hearing protection. Further

protective equipment for head, hands, legs and feet is

recommended. Adequate protective clothing will reduce

personal injury by ﬂying debris or accidental contact with the

sawchain.

• Do not operate a chain saw in a tree. Operation of a chain

saw while up in a tree may result in personalinjury.

• Always keep proper footing and operate the chain saw

only when standing on ﬁxed, secure and level surface.

Slippery or unstable surfaces such as ladders may cause a loss

of balance or control of the chainsaw.

• When cutting a limb that is under tension be alert for

spring back. When the tension in the wood ﬁbers is released

the spring loaded limb may strike the operator and/or throw

the chain saw out ofcontrol.

• Use extreme caution when cutting brush and saplings.

The slender material may catch the saw chain and be

whipped toward you or pull you offbalance.

• Carry the chain saw by the front handle with the chain

saw switched off and away from your body. When

transporting or storing the chain saw always ﬁt the

guide bar cover. Proper handling of the chain saw will

reduce the likelihood of accidental contact with the moving

sawchain.

• Follow instructions for lubricating, chain tensioning and

changing accessories. Improperly tensioned or lubricated

chain may either break or increase the chance forkickback.

• Keep handles dry, clean, and free from oil and grease.

Greasy, oily handles are slippery causing loss ofcontrol.

• Cut wood only. Do not use chain saw for purposes not

intended. For example: do not use chain saw for cutting

plastic, masonry or non-wood building materials. Use

of the chain saw for operations different than intended could

result in a hazardoussituation.

Causes and Operator Prevention of Kickback:

Kickback may occur when the nose or tip of the guide bar

touches an object, or when the wood closes in and pinches the

saw chain in thecut.

Tip contact in some cases may cause a sudden reverse reaction,

kicking the guide bar up and back towards theoperator.

Pinching the saw chain along the top of the guide bar may push

the guide bar rapidly back towards theoperator.

Either of these reactions may cause you to lose control of the

saw which could result in serious personal injury. Do not rely

exclusively upon the safety devices built into your saw. As a

chain saw user, you should take several steps to keep your

cutting jobs free from accident orinjury.

Kickback is the result of tool misuse and/or incorrect operating

procedures or conditions and can be avoided by taking proper

precautions as given below:

• Maintain a firm grip, with thumbs and ﬁngers encircling

the chain saw handles, with both hands on the saw

and position your body and arm to allow you to resist

kickback forces. Kickback forces can be controlled by the

operator, if proper precautions are taken. Do not let go of the

chainsaw.

• Do not overreach and do not cut above shoulder height.

This helps prevent unintended tip contact and enables better

control of the chain saw in unexpectedsituations.

7

ENGLISH

• Only use replacement bars and chains speciﬁed by the

manufacturer. Incorrect replacement bars and chains may

cause chain breakage and/orkickback.

• Follow the manufacturer’s sharpening and maintenance

instructions for the saw chain. Decreasing the depth gauge

height can lead to increasedkickback.

The Following Precautions Should Be

Followed to Minimize Kickback:

1 . Grip saw firmly. Hold the chain saw firmly with both

hands when the motor is running. Use a firm grip with

thumbs and fingers encircling the chain saw handles.

Chain saw will pull forward when cutting on the bottom edge

of the bar, and push backward when cutting along the top

edge of thebar.

2 . Do not overreach.

3 . Keep proper footing and balance at alltimes.

4 . Don’t let the nose of the guide bar contact a log, branch,

ground or otherobstruction.

5 . Don’t cut above shoulderheight.

6 . Use devices such as low kickback chain and reduced

kickback guide bars that reduce the risks associated

withkickback.

7 . Only use replacement bars and chains specified by the

manufacturer or theequivalent.

8 . Never let the moving chain contact any object at the tip

of the guidebar.

9 . Keep the working area free from obstructions such

as other trees, branches, rocks, fences, stumps, etc.

Eliminate or avoid any obstruction that your saw chain could

hit while you are cutting through a particular log orbranch.

10 . Keep your saw chain sharp and properly tensioned. A

loose or dull chain can increase the chance of kickback.

Check tension at regular intervals with the motor stopped and

tool unplugged, never with the motorrunning.

11 . Begin and continue cutting only with the chain moving

at full speed. If the chain is moving at a slower speed, there is

a greater chance for kickback tooccur.

12 . Cut one log at atime.

13 . Use extreme caution when re-entering a previous cut.

Engage ribbed bumpers into wood and allow chain to reach

full speed before proceeding withcut.

14 . Do not attempt plunge cuts or borecuts.

15 . Watch for shifting logs or other forces that could close a

cut and pinch or fall intochain.

Kickback Safety Features



WARNING: The following features are included on your

saw to help reduce the hazard of kickback; however such

features will not totally eliminate this dangerous reaction.

As a chain saw user do not rely only on safety devices.

You must follow all safety precautions, instructions, and

maintenance in this manual to help avoid kickback and

other forces which can result in seriousinjury.

• Reduced-Kickback Guide Bar, designed with a small radius

tip which reduces the size of the kickback danger zone on

bar tip. A reduced - kickback guide bar is one which has

been demonstrated to significantly reduce the number and

seriousness of kickbacks when tested in accordance with safety

requirements for electric chainsaws.

• Low-Kickback Chain, designed with a contoured depth gauge

and guard link which deflect kickback force and allow wood to

gradually ride into thecutter.

• Do not operate chain saw while in a tree, on a ladder, on a

scaffold, or from any unstablesurface.

• Hold tool by insulated gripping surfaces when performing an

operation where the cutting tool may contact hidden wiring.

Contact with a “live” wire will make exposed metal parts of the

tool “live” and shock theoperator.

• Do not attempt operations beyond your capacity or

experience. Read thoroughly and understand completely all

instructions in thismanual.

• Before you start chain saw, make sure saw chain is not

contacting anyobject.

• Do not operate a chain saw with one hand! Serious injury to the

operator, helpers, or bystanders may result from one handed

operation. A chain saw is intended for two-handed useonly.

• Keep the handles dry, clean, and free of oil orgrease.

• Do not allow dirt, debris, or sawdust to build up on the motor

or outside airvents.

• Stop the chain saw before setting itdown.

• Do not cut vines and/or small underbrush.

• Use extreme caution when cutting small size brush and

saplings because slender material may catch the saw chain

and be whipped toward you or pull you offbalance.



WARNING: Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities

contains chemicals known to the State of California to

cause cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other

masonry products, and

• a

rsenic and chromium from chemically-treatedlumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed

to filter out microscopicparticles.

• Avoid prolonged contact with dust from power sanding,

sawing, grinding, drilling, and other construction activities.

Wear protective clothing and wash exposed areas with soap

and water. Allowing dust to get into your mouth, eyes, or lay

on the skin may promote absorption of harmfulchemicals.



WARNING: Use of this tool can generate and/or disburse

dust, which may cause serious and permanent respiratory

or otherinjury.

Chainsaw Names and Terms

• Bucking - The process of cross cutting a felled tree or log intolengths.

8

ENGLISH

• Motor Brake - A device used to stop the saw chain when the

trigger isreleased.

• Chain Saw Powerhead - A chain saw without the saw chain

and guidebar.

• Drive Sprocket or Sprocket - The toothed part that drives the

sawchain.

• Felling - The process of cutting down atree.

• Felling Back Cut - The final cut in a tree felling operation made

on the opposite side of the tree from the notchingcut.

• Front Handle - The support handle located at or toward the

front of the chainsaw.

• Front Hand Guard - A structural barrier between the front

handle of a chain saw and the guide bar, typically located

close to the hand position on the fronthandle.

• Guide Bar - A solid railed structure that supports and guides

the sawchain.

• Guide Bar Scabbard - Enclosure fitted over guide bar to prevent

tooth contact when saw is not inuse.

• Kickback - The backward or upward motion, or both of the guide

bar occurring when the saw chain near the nose of the top area

of the guide bar contacts any object such as a log or branch, or

when the wood closes in and pinches the saw chain in thecut.

• Kickback, Pinch - The rapid pushback of the saw which can

occur when the wood closes in and pinches the moving saw

chain in the cut along the top of the guidebar.

• Kickback, Rotational - The rapid upward and backward

motion of the saw which can occur when the moving saw

chain near the upper portion of the tip of the guide bar

contacts an object, such as a log orbranch.

• Limbing - Removing the branches from a fallen tree

• Low-Kickback Chain - A chain that reduces the kickback

performance requirements. (when tested on a representative

sample of chain saws.)

• Normal Cutting Position - Those positions assumed in

performing the bucking and fellingcuts.

• Notching Undercut - A notch cut in a tree that directs the tree’sfall.

• Rear Handle - The support handle located at or toward the

rear of thesaw.

• Reduced Kickback Guide Bar - A guide bar which has been

demonstrated to reduce kickbacksignificantly.

• Replacement Saw Chain - A chain that reduces the kickback

performance requirements when tested with specific

chainsaws.

• Saw Chain - A loop of chain having cutting teeth, that cut the

wood,and that is driven by the motor and is supported by the

guidebar.

• Ribbed Bumper - The ribs used when felling or bucking to pivot

the saw and maintain position whilesawing.

• Switch - A device that when operated will complete or interrupt

an electrical power circuit to the motor of the chainsaw.

• Switch Linkage - The mechanism that transmits motion from

a trigger to theswitch.

• Switch Lockout - A movable stop that prevents the

unintentional operation of the switch until manuallyactuated.

Residual Risks

In spite of the application of the relevant safety regulations

and the implementation of safety devices, certain residual risks

cannot be avoided. These are:

• Impairment ofhearing.

• Risk of personal injury due to flyingparticles.

• Risk of burns due to accessories becoming hot

duringoperation.

• Risk of personal injury due to prolongeduse.

Electrical Safety

The electric motor has been designed for one voltage only.

Always check that the battery pack voltage corresponds to the

voltage on the rating plate. Also make sure that the voltage of

your charger corresponds to that of yourmains.

Your STANLEYFATMAX charger is double insulated

in accordance with EN60335; therefore no earth wire

isrequired.

If the supply cord is damaged, it must be replaced by a specially

prepared cord available through the STANLEYFATMAX

serviceorganisation.

Using an Extension Cable

An extension cord should not be used unless absolutely

necessary. Use an approved extension cable suitable for

the power input of your charger (see Technical Data). The

minimum conductor size is 1mm

2

; the maximum length

is30m.

When using a cable reel, always unwind the cablecompletely.

SAVE THESE INSTRUCTIONS

Chargers

STANLEYFATMAX chargers require no adjustment and are

designed to be as easy as possible tooperate.

Important Safety Instructions for All

Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instructions for compatible battery

chargers (refer to TechnicalData).

• Before using charger, read all instructions and cautionary

markings on charger, battery pack, and product using

batterypack.



WARNING: Shock hazard. Do not allow any liquid to get

inside charger. Electric shock mayresult.



WARNING: We recommend the use of a residual current

device with a residual current rating of 30mA orless.



CAUTION: Burn hazard. To reduce the risk of injury,

charge only STANLEYFATMAX rechargeable batteries.

Other types of batteries may burst causing personal injury

anddamage.



CAUTION: Children should be supervised to ensure that

they do not play with theappliance.

NOTICE: Under certain conditions, with the charger

plugged into the power supply, the exposed charging

contacts inside the charger can be shorted by foreign

9

ENGLISH

material. Foreign materials of a conductive nature such

as, but not limited to, steel wool, aluminum foil or any

buildup of metallic particles should be kept away from

charger cavities. Always unplug the charger from the

power supply when there is no battery pack in the cavity.

Unplug charger before attempting to clean

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger

and battery pack are specifically designed to worktogether.

• These chargers are not intended for any uses other

than charging STANLEYFATMAX rechargeable batteries.

Any other uses may result in risk of fire, electric shock

orelectrocution.

• Do not expose charger to rain orsnow.

• Pull by plug rather than cord when disconnecting

charger. This will reduce risk ofdamage to electric plug

andcord.

• Make sure that cord is located so that it will not be

stepped on, tripped over, or otherwise subjected to

damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk

of fire,electric shock, orelectrocution.

• Do not place any object on top of charger or place

the charger on a soft surface that might block the

ventilation slots and result in excessive internal heat.

Place the charger in a position away from any heat source. The

charger is ventilated through slots in the top and the bottom

of thehousing.

• Do not operate charger with damaged cord or plug—

have them replacedimmediately.

• Do not operate charger if it has received a sharp blow,

been dropped, or otherwise damaged in any way. Take it

to an authorised servicecentre.

• Do not disassemble charger; take it to an authorised

service centre when service or repair is required. Incorrect

reassembly may result in a risk of electric shock, electrocution

orfire.

• In case of damaged power supply cord the supply cord must be

replaced immediately by the manufacturer, its service agent or

similar qualified person to prevent anyhazard.

• Disconnect the charger from the outlet before

attempting any cleaning. This will reduce the risk of

electric shock. Removing the battery pack will not reduce

thisrisk.

• NEVER attempt to connect two chargerstogether.

• The charger is designed to operate on standard

230V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharger.

Charging a Battery (Fig. B)

1. Plug the charger into an appropriate outlet before inserting

batterypack.

2. Insert the battery pack

14

into the charger, making sure the

battery pack is fully seated in the charger. The red (charging)

light will blink repeatedly indicating that the charging

process hasstarted.

3. The completion of charge will be indicated by the red

light remaining ON continuously. The battery pack is fully

charged and may be used at this time or left in the charger.

To remove the battery pack from the charger, push the

battery release button

15

on the batterypack.

NOTE: To ensure maximum performance and life of lithium-ion

battery packs, charge the battery pack fully before firstuse.

Charger Operation

Refer to the indicators below for the charge status of the

batterypack.

Charge Indicators

Charging

Fully Charged

Hot/Cold Pack Delay*

* The red light will continue to blink, but a yellow indicator light

will be illuminated during this operation. Once the battery pack

has reached an appropriate temperature, the yellow light will

turn off and the charger will resume the chargingprocedure.

The compatible charger(s) will not charge a faulty battery pack.

The charger will indicate faulty battery by refusing to light or by

displaying problem pack or charger blinkpattern.

NOTE: This could also mean a problem with acharger.

If the charger indicates a problem, take the charger and battery

pack to be tested at an authorised servicecentre.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot or too

cold, it automatically starts a Hot/Cold Pack Delay, suspending

charging until the battery pack has reached an appropriate

temperature. The charger then automatically switches to the

pack charging mode. This feature ensures maximum battery

packlife.

A cold battery pack will charge at a slower rate than a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery packwarms.

Wall Mounting

These chargers are designed to be wall mountable or to sit

upright on a table or work surface. If wall mounting, locate the

charger within reach of an electrical outlet, and away from a

corner or other obstructions which may impede air flow. Use

the back of the charger as a template for the location of the

mounting screws on the wall. Mount the charger securely using

drywall screws (purchased separately) at least 25.4mm long

with a screw head diameter of 7–9mm, screwed into wood to

an optimal depth leaving approximately 5.5mm of the screw

exposed. Align the slots on the back of the charger with the

exposed screws and fully engage them in theslots.

10

ENGLISH

Charger Cleaning Instructions



WARNING: Shock hazard. Disconnect the charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using a

cloth or soft non-metallic brush. Do not use water or any

cleaning solutions. Never let any liquid get inside the tool;

never immerse any part of the tool into aliquid.

Battery Packs

Important Safety Instructions for All

Battery Packs

When ordering replacement battery packs, be sure to include

catalogue number andvoltage.

The battery pack is not fully charged out of the carton. Before

using the battery pack and charger, read the safety instructions

below. Then follow charging proceduresoutlined.

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Inserting or removing the battery from the charger may

ignite the dust orfumes.

• Never force battery pack into charger. Do not modify

battery pack in any way to fit into a non-compatible

charger as battery pack may rupture causing serious

personalinjury.

• Charge the battery packs only in STANLEYFATMAXchargers.

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in

locations where the temperature may reach or exceed

40 ˚C (104 ˚F) (such as outside sheds or metal buildings

in summer).

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when

lithium-ion battery packs areburned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open eye

for 15 minutes or until irritation ceases. If medical attention

is needed, the battery electrolyte is composed of a mixture of

liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause respiratory

irritation. Provide fresh air. If symptoms persists, seek

medicalattention.



WARNING: Burn hazard. Battery liquid may be flammable

if exposed to spark orflame.



WARNING: Never attempt to open the battery pack for

any reason. If battery pack case is cracked or damaged,

do not insert into charger. Do not crush, drop or damage

battery pack. Do not use a battery pack or charger that

has received a sharp blow, been dropped, run over or

damaged in any way (i.e., pierced with a nail, hit with

a hammer, stepped on). Electric shock or electrocution

may result. Damaged battery packs should be returned to

service centre forrecycling.



WARNING: Fire hazard. Do not store or carry the

battery pack so that metal objects can contact

exposed battery terminals. For example, do not place

the battery pack in aprons, pockets, tool boxes, product kit

boxes, drawers, etc., with loose nails, screws, keys,etc.



CAUTION: When not in use, place tool on its side on

a stable surface where it will not cause a tripping

or falling hazard. Some tools with large battery packs

will stand upright on the battery pack but may be easily

knockedover.

Transportation



WARNING: Fire hazard. Transporting batteries can

possibly cause fire if the battery terminals inadvertently

come in contact with conductive materials. When

transporting batteries, make sure that the battery

terminals are protected and well insulated from materials

that could contact them and cause a shortcircuit.

NOTE: Lithium-ion batteries should not be put in

checkedbaggage.

STANLEYFATMAX batteries comply with all applicable shipping

regulations as prescribed by industry and legal standards which

include UN Recommendations on the Transport of Dangerous

Goods; International Air Transport Association (IATA) Dangerous

Goods Regulations, International Maritime Dangerous Goods

(IMDG) Regulations, and the European Agreement Concerning

The International Carriage of Dangerous Goods by Road (ADR).

Lithium-ion cells and batteries have been tested to section 38.3

of the UN Recommendations on the Transport of Dangerous

Goods Manual of Tests andCriteria.

In most instances, shipping a STANLEYFATMAX battery pack

will be excepted from being classified as a fully regulated Class

9 Hazardous Material. In general, only shipments containing a

lithium-ion battery with an energy rating greater than 100 Watt

Hours (Wh) will require being shipped as fully regulated Class

9. All lithium-ion batteries have the Watt Hour rating marked

on the pack. Furthermore, due to regulation complexities,

STANLEYFATMAX does not recommend air shipping lithium-ion

battery packs alone regardless of Watt Hour rating. Shipments of

tools with batteries (combo kits) can be air shipped as excepted

if the Watt Hour rating of the battery pack is no greater than

100Whr.

Regardless of whether a shipment is considered excepted

or fully regulated, it is the shipper's responsibility to consult

the latest regulations for packaging, labeling/marking and

documentationrequirements.

The information provided in this section of the manual is

provided in good faith and believed to be accurate at the time

the document was created. However, no warranty, expressed or

implied, is given. It is the buyer’s responsibility to ensure that its

activities comply with the applicableregulations.

Storage Recommendations

1. The best storage place is one that is cool and dry away

from direct sunlight and excess heat or cold. For optimum

battery performance and life, store battery packs at room

temperature when not inuse.

11

ENGLISH

2. For long storage, it is recommended to store a fully charged

battery pack in a cool, dry place out of the charger for

optimalresults.

NOTE: Battery packs should not be stored completely depleted

of charge. The battery pack will need to be recharged beforeuse.

Labels on Charger and Battery Pack

In addition to the pictographs used in this manual, the labels

on the charger and the battery pack may show the following

pictographs:

Read instruction manual beforeuse.

See Technical Data for chargingtime.

Do not probe with conductiveobjects.

Do not charge damaged batterypacks.

Do not expose towater.

Have defective cords replacedimmediately.

Charge only between 4 ˚C and 40 ˚C.

Only for indooruse.

Discard the battery pack with due care for

theenvironment.

Charge STANLEYFATMAX battery packs only

with designated STANLEYFATMAX chargers.

Charging battery packs other than the

designated STANLEYFATMAX batteries with a

STANLEYFATMAX charger may make them burst or

lead to other dangeroussituations.

Do not incinerate the batterypack.

Battery Type

The SFMCCS630 operates on a 18 volt batterypack.

These battery packs may be used: SFMCB202, SFMCB204,

SFMCB206. Refer to Technical Data for moreinformation.

Package Contents

The package contains:

1 Chainsaw

1 Scabbard

1 Bar 30cm

1 Chain 30cm

1 Instruction manual

1 Li-Ion battery pack

1 Li-Ion battery charger

• Check for damage to the tool, parts or accessories which may

have occurred duringtransport.

• Take the time to thoroughly read and understand this manual

prior tooperation.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual beforeuse.

Wear earprotection.

Wear eyeprotection.

Always wear a dustmask.

Do not leave inrain.

Tip contact can cause the guide bar to move suddenly

upward and backward, which can cause seriousinjury.

Contact of the guide bar tip with any object should

beavoided.

Rotational direction of the sawchain.

Always use two hands when operating thechainsaw.

Switch the tool off. Before performing any

maintenance on the tool, remove the battery from

thetool.

Directive 2000/14/EC guaranteed soundpower.

Date Code Position

The date code, which also includes the year of manufacture, is

printed into thehousing.

Example:

2019 XX XX

Year of Manufacture

Description (Fig. A)



WARNING: Never modify the power tool or any part of it.

Damage or personal injury couldresult.

1

ON/OFF trigger switch

2

Lock-off lever

3

Chain brake/front hand

guard

4

Guide bar

5

Saw chain

6

Sprocket cover

7

Bubble Level

8

Bar adjust locking knob

9

Chain tensioning knob

10

Oil level indicator

11

Guide bar scabbard

12

ENGLISH

12

Rear handle

13

Front handle

14

Battery

15

Battery release button

16

Oil cap

Intended Use

Your STANLEYFATMAX SFMCCS630 Chainsaw is ideal for pruning

applications and cutting logs up to 26cm indiameter.

DO NOT use under wet conditions or in the presence of

flammable liquids orgases.

This chainsaw is a professional powertool.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

• Young children and the infirm. This appliance is not

intended for use by young children or infirm persons

withoutsupervision.

• This product is not intended for use by persons (including

children) suffering from diminished physical, sensory or

mental abilities; lack of experience, knowledge or skills

unless they are supervised by a person responsible for their

safety. Children should never be left alone with thisproduct.

ASSEMBLY AND ADJUSTMENTS



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.



WARNING: Use only STANLEYFATMAX battery packs

andchargers.

Inserting and Removing the Battery Pack

from the Tool (Fig. B)

NOTE: Make sure your battery pack

14

is fullycharged.

To Install the Battery Pack into the Tool

1. Align the battery pack

14

with the rails inside the tool

(Fig.B).

2. Slide it into the tool until the battery pack is firmly seated

and ensure that you hear the lock snap intoplace.

To Remove the Battery Pack from the Tool

1. Press the release button

15

and firmly pull the battery pack

out of the toolhandle (Fig. B).

2. Insert battery pack into the charger as described in the

charger section of thismanual.

Fuel Gauge Battery Packs (Fig. B)

Some STANLEYFATMAX battery packs include a fuel gauge

which consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

To actuate the fuel gauge, press and hold the fuel gauge

button

17

. A combination of the three green LED lights will

illuminate designating the level of charge left. When the level of

charge in the battery is below the usable limit, the fuel gauge

will not illuminate and the battery will need to berecharged.

NOTE: The fuel gauge is only an indication of the charge left on

the battery pack. It does not indicate tool functionality and is

subject to variation based on product components, temperature

and end-userapplication.

ASSEMBLY

Installing the Guide Bar and Saw Chain

(Fig.A, C–E)



CAUTION: Sharp chain. Always wear protective gloves

when handling the chain. The chain is sharp and can cut

you when it is notrunning.



WARNING: Sharp moving chain. To prevent accidental

operation, ensure that battery is removed from the tool

before performing the following operations. Failure to do

this could result in serious personalinjury.

If the saw chain

5

and guide bar

4

are packed separately in the

carton. The chain has to be attached to the bar, and both must

be attached to the body of thetool.

1. Place the saw on a flat, firmsurface.

2. Flip up locking lever and rotate the bar adjust locking

knob

8

counterclockwise as shown in FigureC to remove

sprocket cover

6

.

3. Wearing protective gloves, grasp the saw chain

5

and wrap

it around the guide bar

4

, ensuring the teeth are facing the

correct direction (see FigureD)

4. Ensure the chain is properly set in the slot around the entire

guidebar.

5. Place the saw chain around the sprocket

18

. While lining up

the slot on the guide bar with chain tensioning pin

20

, and

the bolt

19

, on the base of the tool as shown in FigureE.

6. Once in place, hold the bar still, replace sprocket cover

6

.

Make sure tool-free tension assembly bolt hole on the

cover lines up with the bolt

19

, in the main housing. Flip

up locking lever and rotate the bar adjust locking knob

8

clockwise until it clicks, then loosen knob one full turn, so

that the saw chain can be properlytensioned.

7. Rotate the chain tensioning knob

9

clockwise to increase

tension as shown in FigureE. Make sure the saw chain

5

is

snug around the guide bar

4

. Tighten the bar adjust locking

knob until it clicks. The bar is secure after three audible clicks

are heard. Further tightening is notrequired.

Adjusting Chain Tension (Fig. A, F)



CAUTION: Sharp chain. Always wear protective gloves

when handling the chain. The chain is sharp and can cut

you when it is notrunning.



WARNING: Sharp moving chain. To prevent accidental

operation, ensure that battery is removed from the tool

before performing the following operations. Failure to do

this could result in serious personalinjury.

1. With the saw on a flat, firm surface, check the saw chain

5

tension. The tension is correct when the chain snaps back

after being pulled 3mm away from the guide bar

4

with

light force from the index finger and thumb as shown in

FigureF. There should be no “sag” between the guide bar

and the chain on the underside as shown in FigureF.

13

ENGLISH

2. To adjust saw chain tension, flip up locking tab and rotate

the bar adjust locking knob

8

counterclockwise one full

turn. Rotate the chain tensioning knob

9

clockwise until

the chain tension is correct as instructedabove.

3. Do not over-tension the chain as this will lead to excessive

wear and will reduce the life of the bar andchain.

4. Once chain tension is correct, securely tighten bar adjust

lockingknob.

NOTE: The bar adjust locking knob has a detent tightening

system. The sprocket cover is secure after three audible clicks are

heard. Further tightening is notrequired.

5. When the chain is new, check the tension frequently (after

removing battery) during the first 2 hours of use as a new

chain stretchesslightly.

Replacing the Saw Chain (Fig.A, G)



CAUTION: Sharp chain. Always wear protective gloves

when handling the chain. The chain is sharp and can cut

you when it is notrunning.



WARNING: Sharp moving chain. To prevent accidental

operation, ensure that battery is removed from the tool

before performing the following operations. Failure to do

this could result in serious personalinjury.

1. Flip up locking tab and rotate the bar adjust locking knob

8

counterclockwise to release chaintension.

2. Remove sprocket cover

6

as described in Installing the

Guide Bar and Saw Chainsection.

3. Lift the worn saw chain

5

out of the groove in the guide

bar

4

.

4. Place the new chain in the slot of the guide bar, making sure

the saw teeth are facing the correct direction by matching

the arrow on the chain with the graphic on the sprocket

cover

6

shown in FigureG.

5. Follow instructions for

Installing the Guide Bar and

SawChain

.

Replacement chain and bar are available from your nearest

STANLEYFATMAX servicecenter.

• SFMCCS630 requires replacement chain # STZCS230, service

part number N580237. Replacement 30cm bar #STZCS1230,

service part numberN727097.

Saw Chain and Guide Bar Oiling (Fig.H)

Auto Oiling System

This chain saw is equipped with an auto oiling system that

keeps the saw chain and guide bar constantly lubricated. The

oil level indicator

10

shows the level of the oil in the chain

saw. If the oil level is less than a quarter full, remove the battery

from the chain saw and refill with the correct type of oil. Always

empty oil tank when finishedcutting.

NOTE: Use a high quality bar and chain oil for proper chain

and bar lubrication. As a temporary substitute, a non-detergent

SAE30 weight motor oil can be used. The use of a vegetable

based bar and chain oil is recommended when pruning trees.

Mineral oil is not recommended because it may harm trees.

Never use waste oil or very thick oil. These may damage your

chainsaw.

Filling the Oil Reservoir

1. Flip down locking lever and unscrew counterclockwise

a quarter turn and then remove the oil cap

16

. Fill the

reservoir with the recommended bar and chain oil until the

oil level has reached the top of the oil level indicator

10

.

2. Refit the oil cap and tighten clockwise a quarter turn. Flip up

locking lever to its lockedposition.

3. Periodically switch the chain saw off and check the oil

level indicator to ensure the bar and chain are being

properlyoiled.

Transporting Saw (Fig.A, I)

1. Always remove the battery from the tool and cover

the guide bar

4

with the scabbard

11

(FigureI) when

transporting thesaw.

2. Engage chain brake by pushing chain brake / front hand

guard

3

forward.

OPERATION

Instructions for Use



WARNING: Always observe the safety instructions and

applicableregulations.



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

Proper Hand Position (Fig. A, J)



WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.



WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

Proper hand position requires the left hand on the front

handle

13

, with the right hand on the rear handle

12

.

Operating the Chain Saw (Fig.A)



WARNING: Read and understand all instructions. Failure

to follow all instructions listed below may result in electric

shock, fire and/or serious personalinjury.

• Guard Against Kickback which can result in severe

injury or death. See Important Safety Instructions

Guard Against Kickback, to avoid the risk

ofkickback.

• Do not overreach. Do not cut above chest height.

Make sure your footing is firm. Keep feet apart. Divide

your weight evenly on bothfeet.

• Use a firm grip with your left hand on the front

handle

13

and your right hand on the rear

handle

12

so that your body is to the left of the

guidebar.

• Do not hold chain saw by front hand guard/ chain

brake

3

. Keep elbow of left arm locked so that left

arm is straight to withstand akickback.

14

ENGLISH



WARNING: Never use a cross-handed grip (left hand on

the rear handle and right hand on the front handle).



WARNING: Never allow any part of your body to be in line

with the guide bar

4

when operating the chainsaw.

• Never operate while in a tree, in any awkward position

or on a ladder or other unstable surface. You may lose

control of saw causing severeinjury.

• Keep the chain saw running at full speed the entire

time you arecutting.

• Allow the chain to cut for you. Exert only light pressure.

Do not put pressure on chain saw at end ofcut.



WARNING: When not in use always have the chain

brake engaged and batteryremoved.

On / Off Switch (Fig.L)

Always be sure of your footing and grip the chain saw firmly

with both hands with the thumb and fingers encircling

bothhandles.

To turn the unit on, ensure chain brake is not engaged. Slide

the lock off lever

2

, shown in FigureL, and squeeze the trigger

switch

1

. Once the unit is running, you may release the lock

offlever.

In order to keep the unit running you must continue to squeeze

the trigger. To turn the unit off, release thetrigger.

NOTE: If too much force is applied while making a cut the

saw will turn off. To restart saw, you must release the trigger

switch

1

before the saw will restart. Begin your cut again this

time with less force. Allow the saw to cut at its ownpace.



WARNING: Never attempt to lock a switch in the

ONposition.

Setting The Chain Brake (Fig.K)

Your chain saw is equipped with a motor chain braking system

which will stop the chain quickly in case ofkickback.

1. Remove the battery from thetool.

2. To engage the chain brake, push the chain brake / front

hand guard

3

forward until it clicks intoplace.

3. Pull the chain brake / front hand guard

3

towards the front

handle

13

into the “set” position as shown in FigureK.

4. The tool is now ready touse.

NOTE: In the event of kickback, your left hand will come in

contact with the front guard, pushing it forward, toward the

workpiece. This will stop thetool.

Testing The Chain Brake (Fig.A)

Test the chain brake before every use to make sure it

operatescorrectly.

1. Place the tool on a flat, firm surface. Make sure the saw

chain

5

is clear of theground.

2. Grip the tool firmly with both hands and turn the chain

sawon.

3. Rotate your left hand forward around the front handle

13

so the back of your hand comes in contact with the Chain

brake / front hand guard

3

and push it forward, toward the

workpiece. The saw chain should stopimmediately.

NOTE: If saw does not stop immediately, stop use of tool and

bring it to a STANLEYFATMAX service center nearestyou.



WARNING: Make sure to set chain brake beforecutting.

Bubble Level (Fig.A, T)



WARNING: Do not operate above shoulder height Align

bubble levels prior to making acut.

Ideal for horizontal cutting to ensure a straight, flat cut for

fencing, decking or railingposts.

1. Align both bubble levels

7

.

2. Always start a cut with the saw chain running at fullspeed.

3. Place the bottom spike

22

of the chain saw behind the area

of the initialcut.

4. Once a cut has begun and a notch is established in the

material, do not change the angle of the cut.

NOTE: Changing the angle will cause the bar to bend.

Common Cutting Techniques

(Fig. A, M, N, R, S, T, U)

Felling

The process of cutting down a tree. Be sure battery is fully

charged before felling a tree so you can finish on a single

charge. Do not fell trees in high windconditions.



WARNING: Felling can result in injury. It should only be

performed by a trainedperson.

• A retreat path should be planned and cleared as necessary

before cuts are started. The retreat path should extend

back and diagonally to the rear of the expected line of fall.

(FigureR)

DIRECTION

OF

FALL

RETREAT

45°

TREE

Fig. R

45°

RETREAT

• Before felling is started, consider the natural lean of the

tree, the location of larger branches and the wind direction

to judge which way the tree will fall. Have wedges (wood,

plastic or aluminum) and a heavy mallet handy. Remove

dirt, stones, loose bark, nails, staples, and wire from the tree

where the felling cuts are to bemade.

• Notching Undercut - Make the notch 1/3 of the diameter of

the tree, perpendicular to the direction of the fall. Make the

lower horizontal notching cut first. This will help to avoid

pinching of either the saw chain or the guide bar when the

second notch cut is being made (FigureS).

15

ENGLISH

• Felling Back Cut - Make the felling back cut at least 51mm

higher than the horizontal notching cut. Keep the felling

back cut parallel to the horizontal notching cut. Make the

felling back cut so enough wood is left to act as a hinge. The

hinge wood keeps the tree from twisting and falling in the

wrong direction. Do not cut through the hinge (FigureS).

• As the felling cut gets close to the hinge the tree should

begin to fall. If there is any chance that the tree may not fall

in the desired direction or it may rock back and bind the

saw chain, stop cutting before the felling cut is complete

and use wedges to open the cut and drop the tree along

the desired line of fall. When the tree begins to fall remove

the chain saw from the cut, stop the motor, put the chain

saw down, then use the retreat path planned. Be alert for

overhead limbs falling and watch yourfooting.

DIRECTION OF FALL

51 mm

HINGE

NOTCH

FELLING BACK CUT

Fig. S

Limbing

Removing the branches from a fallen tree. When limbing, leave

larger lower limbs to support the log off the ground. Remove

the small limbs in one cut. Branches under tension should be

cut from the bottom of the branch towards the top to avoid

binding the chain saw as shown in FigureM. Trim limbs from

opposite side keeping tree stem between you and saw. Never

make cuts with saw between your legs or straddle the limb to

becut.

Bucking



WARNING: Recommend that first time users should

practice cutting on a sawhorse.

Cutting a felled tree or log into lengths. How you should

cut depends on how the log is supported. Use a saw horse

(FigureN) wheneverpossible.

• Always start a cut with the chain running at fullspeed.

• Place the bottom spike

22

of the chain saw behind the area

of the initial cut as shown in FigureT.

• Turn the chain saw on then rotate the chain and bar down

into the tree, using the spike as ahinge.

• Once the chain saw gets to a 45 degree angle, level the

chain saw again and repeat steps until you cut fullythrough.

• When the tree is supported along its entire length, make a

cut from the top (overbuck), but avoid cutting the earth as

this will dull your sawquickly.

CUT FROM TOP (OVERBUCK)AVOID

CUTTING EARTH

Fig. T

22

• Figure U- When supported at one end

First, cut 1/3 the diameter from the underside (underbuck).

Then make the finishing cut by overbucking to meet the

firstcut.

1

2

2nd CUT OVERBUCK

(2/3 DIAMETER) TO MEET 1st

CUT (TO AVOID PINCHING)

1st CUT UNDERBUCK

(1/3 DIAMETER)

AVOID SPLINTERING

Fig. U

• Figure V- When supported at bothends.

First, cut 1/3 down from the top overbuck. Then make the

finished cut by underbucking the lower 2/3 to meet the

firstcut.

2nd CUT UNDERBUCK (2/3

DIAMETER) TO MEET 1st CUT

(TO AVOID PINCHING)

1st CUT OVERBUCK

(1/3 DIAMETER)

TO AVOID SPLINTERING

Fig. V

• When on a slope always stand on the uphill side of the

log. When “cutting through”, to maintain complete control

reduce the cutting pressure near the end of the cut without

relaxing your grip on the chain saw handles. Don’t let the

chain contact the ground. After completing the cut, wait

for the saw chain to stop before you move the chain saw.

Always stop the motor before moving from cut tocut.

CARE AND MAINTENANCE

Use only mild soap and damp cloth to clean the tool. Do not

use solvents to clean the plastic housing of the saw. Never let

any liquid get inside the tool; never immerse any part of the tool

into aliquid.

IMPORTANT: To assure product SAFETY and RELIABILITY,

repairs, maintenance and adjustment should be performed by

a STANLEYFATMAX authorized service center, always using

identical replacementparts.

16

ENGLISH

Regular maintenance ensures a long effective life for your

chainsaw.

Chain and Bar

After every few hours of use, remove the sprocket cover, guide

bar and chain and clean thoroughly using a soft bristle brush.

Ensure oiling hole on bar is clear of debris. When replacing dull

chains with sharp chains it is good practice to flip the chain bar

from bottom totop.

Saw Chain Sharpening (Fig. O–Q)



CAUTION: Sharp chain. Always wear protective gloves

when handling the chain. The chain is sharp and can cut

you when it is notrunning.



WARNING: Sharp moving chain. To prevent accidental

operation, ensure that battery is removed from the tool

before performing the following operations. Failure to do

this could result in serious personalinjury.

NOTE: The cutters will dull immediately if they touch the

ground or a nail whilecutting.

To get the best possible performance from your chain saw it is

important to keep the teeth of the chain sharp. Follow these

helpful tips for proper saw chain sharpening:

1. For best results use a 4.5mm file and a file holder or filing

guide to sharpen your chain. This will ensure you always get

the correct sharpeningangles.

2. Place the file holder flat on the top plate and depth gauge

of thecutter.

3. Figure O- Keep the correct top plate

21

filing angle line

of 30° on your file guide parallel with your chain (file at 60°

from chain viewed from the side).

4. Sharpen cutters on one side of the chain first. File from the

inside of each cutter to the outside. Then turn your saw

around and repeat the processes (2,3,4) for cutters on the

other side of thechain.

NOTE: Use a flat file to file the tops of the rakers (portion of

chain link in front of the cutter) so they are about 0.635mm

below the tips of the cutters as shown in FigureP.

5. Figure Q- Keep all cutter lengthsequal.

6. If damage is present on the chrome surface of the top plates

or side plates, file back until such damage isremoved.



CAUTION: After filing, the cutter will be sharp, use extra

caution during thisprocess.

NOTE: Each time the chain is sharpened, it loses some of the

low kickback qualities and extra caution should be used. It

is recommended that a chain be sharpened no more than

fourtimes.

Accessories



WARNING: The use of accessories not recommended in

this manual may behazardous.

Replacement chain and bar are available from your nearest

STANLEYFATMAX authorized service center. For use only with

low kick back bar andchain.

Available bars and chains for SFMCCS630:

• Bar: 30cm service part number N727097

• Chain: 30cm service part number N580237

Optional Accessories



WARNING: Since accessories, other than those offered by

STANLEYFATMAX, have not been tested with this product,

use of such accessories with this tool could be hazardous.

To reduce the risk of injury, only STANLEYFATMAX

recommended accessories should be used with

thisproduct.

Consult your dealer for further information on the

appropriateaccessories.

Maintenance

Your STANLEYFATMAX power tool has been designed

to operate over a long period of time with a minimum of

maintenance. Continuous satisfactory operation depends upon

proper tool care and regularcleaning.



WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

The charger and battery pack are notserviceable.

Lubrication

Refer to Saw Chain and Guide Bar Oiling (Fig.H)

Cleaning



WARNING: Blow dirt and dust out of the main housing

with dry air as often as dirt is seen collecting in and around

the air vents. Wear approved eye protection and approved

dust mask when performing thisprocedure.



WARNING: Never use solvents or other harsh chemicals

for cleaning the non-metallic parts of the tool. These

chemicals may weaken the materials used in these parts.

Use a cloth dampened only with water and mild soap.

Never let any liquid get inside the tool; never immerse any

part of the tool into aliquid.

Protecting the Environment

Separate collection. Products and batteries marked

with this symbol must not be disposed of with normal

householdwaste.

Products and batteries contain materials that can

be recovered or recycled reducing the demand for raw

materials. Please recycle electrical products and batteries

according to local provisions. Further information is available at

www.2helpU.com.

Rechargeable Battery Pack

This long life battery pack must be recharged when it fails

to produce sufficient power on jobs which were easily done

before. At the end of its technical life, discard it with due care for

our environment:

• Run the battery pack down completely, then remove it from

thetool.

17

ENGLISH

• Li-Ion cells are recyclable. Take them to your dealer or a

local recycling station. The collected battery packs will be

recycled or disposed ofproperly.

Guarantee

1 Year Guarantee

All STANLEY FATMAX power tool products include a 1 year

guarantee as standard. In the unlikely event that your powertool

becomes defective due to faulty materials or worksmanship

within 1 year of purchase, STANLEY guarantees to replace or

repair all defective parts free of charge, or – at our discretion –

replace the item free ofcharge.

3 Year Guarantee

Register your STANLEY FATMAX power tool within 4 weeks

of purchase and qualify for an additional 2 year guarantee.

Having registered your power tool, in the unlikely event that

your powertool becomes defective due to faulty materials or

worksmanship, STANLEY guarantees to replace or repair all

defective parts free of charge, or – at our discretion – replace the

item free ofcharge.

TROUBLESHOOTING

Problem Solution

Unit will notstart. • Check batteryinstallation.

• Check battery

chargingrequirements.

• Check that lock off is fully pushed

down prior to moving maintrigger.

Unit shuts down

inuse.

• Chargebattery.

• Unit is being forced. Restart and

apply lesspressure.

Battery

won’tcharge.

• Insert battery into charger until red

charging light illuminates. Charge up

to 8 hours if battery is totallydrained.

• Plug charger into a working outlet.

Refer to Important Charging Notes

for moredetails.

• Check current at receptacle by

plugging anappliance.

• Check to see if receptacle is

connected to a light switch which

turns power off when you turn out

thelights.

• Move charger and appliance to

a surrounding air temperature of

above 4.5°C or below 40.5°C.

Bar /

Chainoverheated.

• Refer to

Adjusting Chain

Tension

section.

• Refer to

Chain Oiling

section.

Chain isloose. • Refer to Adjusting Chain

Tensionsection.

Problem Solution

Poor cutquality.

• Refer to

Adjusting Chain

Tension

section.

NOTE:

Excessive

tension leads to excessive wear and

reduction in life of bar and chain.

Lubricate before each cut. Refer to

Replacing the Saw Chain

section.

Unit runs but does

notcut.

• Chain could be installed backwards.

Refer to sections for installing and

removingchain.

Unit does notoil. • Refill oilreservoir.

• Clean guide bar, sprocket and

sprocket cover. Refer to Care And

Maintenancesection.

18

DEUTSCH

Akku

Katalognr.

Ausgangsspannung

Ladegerät

SFMCB12

SFMCB202 18 X

SFMCB204 18 X

SFMCB206 18 X

"X" Zeigt an, dass der Akku mit diesem speziellen Ladegerät

kompatibel ist. Lesen Sie die Betriebsanleitung für

genauereInformationen.

EG-Konformitätserklärung

Maschinenrichtlinie

18V Kettensäge

SFMCCS630

STANLEYFATMAX erklärt, dass diese unter Technische Daten

beschriebenen Geräte übereinstimmen mit:

2006/42/EC, EN60745-1:2009+A11:2010, EN60745-2-

13:2009+A1:2010.

2000/14/EG, Anhang V

DEKRA Certification B.V., Meander 1051 / P.O. Box 5185 6825 MJ

ARNHEM / 6802 ED

ARNHEM

Niederlande

Kennnummer der benannten Stelle: 0344

L

PA

(gemessener Schallleistungspegel) 86 dB(A)

Unsicherheitsfaktor K = 1,6 dB(A)

L

WA

(garantierte Schallleistung) 100 dB(A)

Diese Produkte entsprechen außerdem den Richtlinien

2014/30/EU, 2011/65/EU. Für weitere Informationen

wenden Sie sich bitte an STANLEYFATMAX unter der

folgenden Adresse oder schauen Sie auf der Rückseite dieser

Betriebsanleitungnach.

Der Unterzeichnete ist verantwortlich für die Zusammenstellung

des technischen Dossiers und gibt diese Erklärung im Namen

von STANLEYFATMAXab.

A. P. Smith

Technical Director

STANLEYFATMAX Europe, Egide Walschaertsstraat14-18,

2800 Mechelen, Belgien

2019-10-11

WARNUNG: Zur Reduzierung der Verletzungsgefahr bitte

die Betriebsanleitunglesen.

Herzlichen Glückwunsch!

Sie haben sich für ein Gerät von STANLEYFATMAX entschieden.

Langjährige Erfahrung, sorgfältige Produktentwicklung und

Innovation machen STANLEYFATMAX zu einem zuverlässigen

Partner für professionelle Anwender vonElektrowerkzeugen.

Technische Daten

SFMCCS630

Spannung V

DC

18

Batterietyp Li-Ion

Typ 1

Länge des Führungsschwerts cm 30

Maximale Kettengeschwindigkeit (Leerlauf) m/s 7,7

Maximale Schnittlänge cm 25

Ölfüllmenge ml 230

Gewicht (ohne Akku) kg 3,86

Lärmwerte und Vibrationswerte (Triax-Vektorsumme) gemäß EN60745-2-13

L

PA

(Emissions-Schalldruckpegel) dB(A) 86

L

WA

(Schallleistungspegel) dB(A) 98

K (Unsicherheit für den angegebenen

Schallpegel)

dB(A) 1,6

Vibrationsemissionswert a

h

= m/s² 3,9

Messungenauigkeit K = m/s² 1,5

Der in diesem Informationsblatt angegebene

Vibrationsemissionswert wurde gemäß einem standardisierten

Test laut EN60745 gemessen und kann für einen Vergleich

zwischen zwei Geräten verwendet werden. Er kann zu einer

vorläufigen Einschätzung der Exposition verwendetwerden.



WARNUNG: Der angegebene Vibrationsemissionswert

bezieht sich auf die Hauptanwendung des Gerätes.

Wenn das Gerät jedoch für andere Anwendungen, mit

anderem Zubehör oder schlecht gewartet eingesetzt

wird, kann die Vibrationsemission verschieden sein. Dies

kann den Expositionsgrad über die Gesamtbetriebszeit

erheblicherhöhen.

Eine Schätzung der Vibrationsstärke sollte auch

berücksichtigen, wie oft das Gerät ausgeschaltet

wird oder über welche Zeit es zwar läuft, aber nicht

wirklich in Betrieb ist. Dies kann die Exposition über die

Gesamtbetriebszeit erheblichmindern.

Identifizieren Sie zusätzliche Sicherheitsmaßnahmen,

um den Bediener vor den Vibrationsauswirkungen zu

schützen, wie: Erhalt des Werkzeugs und Zubehörs, Hände

warm halten, Organisation vonArbeitsmustern.

30 CM 18V KETTENSÄGE

SFMCCS630

Deutsch (übersetzt von den originalanweisungen)

La page charge ...

Stanley SFMCCS630 Le manuel du propriétaire

Ce manuel convient également à

Stanley SFMCCS630 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents