Sony Cordless Telephone SPP-934 Manuel utilisateur

Marque: Sony

Modèle: Cordless Telephone SPP-934

Catégorie: Téléphones

Taper: Manuel utilisateur

Ce manuel convient également à

SPP-934

3-043-723-21 (1)

Operating Instructions

Mode d‘emploi

SPP-934

Cordless

Telephone

WARNING

To prevent fire or shock hazard, do

not expose the unit to rain or

moisture.

To avoid electrical shock, do not open

the cabinet. Refer servicing to

qualified personnel only.

INDUSTRY CANADA NOTICE

NOTICE: The Industry Canada label

identifies certified equipment. This

certification means that the equipment

meets certain telecommunications

network protective, operational and

safety requirements as prescribed in the

appropriate Terminal Equipment

Technical Requirements document(s).

The Department does not guarantee the

equipment will operate to the user’s

satisfaction.

Before installing this equipment, users

should ensure that it is permissible to be

connected to the facilities of the local

telecommunications company. The

equipment must also be installed using

an acceptable method of connection.

The customer should be aware that

compliance with the above conditions

may not prevent degradation of service

in some situations.

Repairs to certified equipment should be

coordinated by a representative

designated by the supplier. Any repairs

or alterations made by the user to this

equipment, or equipment malfunctions

may give the telecommunications

company cause to request the user to

disconnect the equipment.

Users should ensure for their own

protection that the electrical ground

connections of the power utility,

telephone lines and internal metallic

water pipe system, if present, are

connected together. This precaution may

be particularly important in rural areas.

Caution: Users should not attempt to

make such connections themselves, but

should contact the appropriate electric

inspection authority, or electrician, as

appropriate.

NOTICE: The Ringer Equivalence

Number (REN) assigned to each

terminal device provides an indication

of the maximum number of terminal

allowed to be connected to a telephone

interface. The termination on an

interface may consist of any

combination of devices subject only to

the requirement that the sum of the

Ringer Equivalence Number of all the

devices does not exceed 5.

IMPORTANT INSTRUCTION TO

USERS

Your model (SPP-934) has been

approved by the Industry Canada.

Note

Operation is subject to the following two

conditions: (1) this device may not cause

interference, and (2) this device must

accept any interference, including

interference that may cause undesired

operation of the device.

Privacy of communications may not be

ensured when using this telephone.

DIGITAL SECURITY CODE

Your SPP-934 has a random digital

security code which automatically

selects one of over 65,000 digital security

codes.

Table of contents

Getting Started

4 Read this first

5 Step 1: Checking the package

contents

6 Step 2: Setting up the base phone

9 Step 3: Preparing the battery

pack

11 Identifying the parts

Basics

14 Making calls

16 Redialing

17 Receiving calls

Telephone Features

18 Speed dialing

18 Storing phone numbers on

the handset

19 Storing phone numbers on

the base phone

20 Making calls with speed

dialing on the handset

20 Making calls with speed

dialing on the base phone

21 Setting the ringer type

21 Turning off the ringer

22 Checking the ringer type

22 Adjusting the ringer volume

level of the base phone

23 Switching the phones during a

call

23 To switch from the base

phone to the handset

24 To switch from the handset

to the base phone

25 Talking between the handset and

the base phone (Intercom)

25 To talk from the handset to

the base phone

26 To talk from the base phone

to the handset

27 Transferring a call

27 To transfer from the base

phone to the handset

28 To transfer from the handset

to the base phone

29 Having a three-way conference

29 To join the phone

conversation

Additional Information

30 Mounting the base phone on a

wall

31 Notes on power sources

31 Maintenance

32 Troubleshooting

34 Specifications

35 Index

Getting Started

Base phone

Read this first

Before you use your phone, you must first set it up. Here’s a quick way

to set up your phone: Steps 1, 2 and 3.

Step 2 (pages 6 to 8)

Next, you need to do three things to set

up the base phone, including finding the

best location for the base phone.

Step 3 (pages 9 to 10)

Then, insert the battery pack into the

handset and charge it for more than 12

hours.

First, unpack the phone and the supplied

accessories.

Step 1 (page 5)

That’s it!

Handset

About the digital security code

The cordless telephone uses a digital security code to provide protection against unwanted

access to your base phone.

The security code blocks other cordless handsets to make calls through your base phone.

A random security code will be assigned automatically between your base phone and

handset when you charge the battery pack for the first time.

Getting Started

SPEED DIALING

HandsetAC power adaptor (AC-T129)

Base phone

Rechargeable battery

pack (BP-T18)

Step 1

Checking the package contents

Make sure you have received the following items in the package.

If anything is missing, contact your local Sony dealer.

Directories (2)

Telephone line cords (2) Wall bracket/stand

for base phone

Getting Started

Step 2

Away from television

sets and other

electronic equipment

Away from a microwave

oven

Away from excessive

moisture, extremely low

temperatures, dust,

mechanical vibration, or

shock

Away from a personal

computer

Away from another

cordless telephone

Near a central location

and on a level surface

Away from heat sources, such as radiators,

airducts, and sunlight

Away from noise sources such as a window

by a street with heavy traffic

CAUTION: • Should you experience intermittent loss of audio during a conversation, try

moving closer to the base or move base phone away from other noise sources.

• The cordless telephone operates at a frequency that may cause interference to

nearby TVs and VCRs; the base phone should not be placed near or on the top

of a TV or VCR; and, if interference is experienced, moving the cordless

telephone farther away from the TV or VCR will often reduce or eliminate the

interference.

Setting up the base phone

Do the following steps:

• Choose the best location

• Connect the base phone

• Choose the dialing mode

Choose the best location

Where you place the base phone affects the reception quality of the

handset.

Getting Started

continued

If you want to use the wall bracket as the stand, attach it on the bottom

of the base phone before step 1 as illustrated above.

1 Connect the telephone line cord

to the LINE jack and to a

telephone outlet.

2 Connect the AC power adaptor

to the DC IN 9V jack and to an

AC outlet.

3 Raise the antenna. Make sure it

points towards the ceiling.

Connect the base phone

If you want to hang the base phone on the wall, see page 30.

To LINE

To DC IN 9V

To an AC outlet

To the

telephone outlet

Telephone line cord

(supplied)

AC power adaptor

(supplied AC-T129)

Align the

f marks.

Route the code

Getting Started

Notes

• Use only the supplied AC-T129 AC power adaptor.

Do not use any other AC power adaptor.

• Connect the AC power adaptor to a continuous power

supply.

• Place the base phone close to the AC outlet so that

you can unplug the AC power adaptor easily.

Tip

If your telephone outlet is not modular, contact your

telephone service company for assistance.

Choose the dialing mode

For the telephone to work properly, select an appropriate dialing mode

(tone or pulse).

Depending on your dialing system, set the DIAL MODE switch as

follows:

If your dialing system is Set the switch to

Tone TONE

Pulse PULSE

If you aren't sure of your dialing system

Make a trial call with the DIAL MODE switch set to TONE.

If the call connects, leave the switch as is; otherwise, set to PULSE.

Step 2: Setting up the base phone (continued)

Polarity of the plug

Modular

–

DIAL MODE switch

Getting Started

Preparing the battery pack

Charge the battery pack for more than 12 hours before you start using

your phone.

1 Slide open the battery

compartment lid of the handset.

2 Connect the battery connector

with correct polarity (black wire

goes on left side and red wire

goes on right).

3 Close the battery compartment

lid.

4 Place the handset on the base

phone.

The CHARGE lamp lights up

when the handset is properly

seated on the charge terminals

of the base phone. Charge the

battery pack for more than 12

hours so that the battery is fully

charged. The CHARGE lamp

remains lit even after charging

is completed.

continued

Step 3

BP-T18

Black

Red

CHARGE lamp

Getting Started

Battery duration

A fully charged battery pack lasts for about:

• approx. 7 hours when you use the handset continuously.

• approx. 7 days when the handset is in standby mode.

Notes

• The battery pack will gradually discharge over a long period of time, even if

not in use.

• If you leave the battery pack in the handset without charging it, the battery

pack will be completely discharged.

It may require several times of charging to recover its full capacity.

To obtain the best performance from the battery

Do not place the handset on the base phone after each call. The battery

works best if the handset is returned to the base phone after two or

three calls. However, do not leave the handset off the base phone for a

long period of time as this will completely discharge the battery pack.

When to purchase a new battery pack

If the battery lasts only a few minutes even after 12 hours of charging,

the usable life of the battery has expired and needs replacement.

Contact your local Sony authorized dealer or service center, and ask

for a Sony BP-T18 rechargeable battery pack.

Note

Battery life may vary depending on usage condition and ambient temperature.

Step 3: Preparing the battery pack (continued)

Getting Started

Identifying the parts

Refer to the pages indicated in parentheses for details.

Handset

1 Antenna

2 Speaker

3 TALK/BATT LOW lamp

(p. 14, 18)

Lights up during a call, flashes

when you store a phone number for

speed dialing.

4 VOL (volume) switch (p. 14, 17)

Adjusts the handset volume.

5 TALK button (p. 14, 17)

Lets you make or receive a call.

6 Dialing keys (p. 14)

7 Battery compartment (p. 9)

8 TONE button (p. 14, 17)

Allows you to switch temporarily to

tone dialing.

9 SPEED DIAL button (p. 20)

Used to make a call with speed

dialing.

0 OFF button (p. 14, 17)

Allows you to disconnect the call.

qa FLASH button (p. 14, 17)

qs HOLD button (p. 14, 17, 24)

Used to hold a call.

qd INTERCOM button (p. 25)

Used to make an intercom call.

qf CHANNEL button (p. 14, 17)

Used to select a better channel.

qg REDIAL/PAUSE button

(p. 16, 20)

Redials the last number called,

inserts a pause in the dialing

sequence.

qh PGM (Program) button

(p. 18)

Used to store numbers for speed

dialing.

qj Microphone

continued

Getting Started

Identifying the parts (continued)

Base Phone

1 PGM (Program) button

(p. 19)

Used to store numbers for speed

dialing.

2 Dialing keys (p. 15)

3 TONE button (p. 15, 17)

Allows you to switch temporarily to

tone dialing.

4 LINE lamp (p. 15, 17, 23)

Lights when one of the phones is in

use.

5 CHARGE lamp (p. 9)

Lights while the battery is being

charged.

6 HOLD button (p. 15, 17, 23)

Used to hold a call.

7 MIC (microphone)

8 SPEAKERPHONE lamp

(p. 15, 17)

Lights while making or receiving a

call with the base phone.

9 SPEAKERPHONE button

(p. 15, 17)

Used to make or receive a call with

the base phone.

q; Antenna (p. 7, 30)

qa REDIAL/PAUSE button

(p. 16, 20)

Redials the last number called,

inserts a pause in the dialing

sequence.

qs Speaker

qd SPEED DIAL button (p. 20)

Used to make a call with speed

dialing.

qf FLASH button (p. 15, 17)

Getting Started

waw;qlqk

qg VOLUME control (p. 15, 17)

Adjusts the speaker volume.

qh INTERCOM button (p. 26)

Used to make an intercom call.

qj INTERCOM lamp (p. 25)

Lights up during an intercom call.

qk RINGER switch (p. 22)

Adjusts the ringer volume.

ql DIAL MODE switch (p. 8)

Selects pulse or tone dialing.

w; DC IN 9V jack (p. 7, 30)

wa LINE (telephone line) jack

(p. 7, 30)

Basics

Put a call on hold

Select a better channel

Adjust the handset

volume

Switch to tone dialing

temporarily

Switch to another call

(“call waiting” service*)

* You need to subscribe to the service from your telephone company.

1 Pick up the handset from the

base phone.

2 Press (TALK).

The TALK/BATT LOW lamp on

the handset

and the LINE

lamp

on the base phone light up.

The dialing keys light up for 10

seconds.

Then you’ll hear a dial tone. If

you hear error beeps, move

closer to the base phone.

3 Dial the phone number.

4 When you’re done talking, press

(OFF) or replace the handset on

the base phone.

The TALK/BATT LOW lamp on

the handset and the LINE

lamp

on the base phone

go off.

Basics

Making calls

Additional tasks

Notes

• Before dialing, make sure you can hear the dial tone, otherwise you cannot

dial correctly.

• When the TALK/BATT LOW lamp repeats a set of two flashes, the base

phone is in use.

• When you set the handset volume to H (high), the volume will be raised

considerably. Under normal circumstances, set the volume to M (middle).

Do this

Press (HOLD).

The TALK/BATT LOW lamp flashes slowly.

Press (TALK) to resume the conversation.

Press (CHANNEL).

Set the VOL switch to H (high), M (middle) or L

(low).

Press (*TONE) while using the telephone after

you’re connected.

The line remains in tone dialing until

disconnected.

Press (FLASH) to access the flash function.

Press (FLASH) again to return to the first caller.

(REDIAL/PAUSE)

(*TONE)

TALK/BATT

LOW lamp

VOL

switch

(CHANNEL)

(HOLD)

(FLASH)

Basics

Basics 15

(SPEAKERPHONE)

SPEAKERPHONE

lamp

VOLUME

control

LINE lamp

(REDIAL/PAUSE)

(FLASH)

(*TONE)

(HOLD)

If the handset battery becomes weak during a call

You hear a beep every three seconds and the TALK/BATT LOW lamp

on the handset flashes.

The call will disconnect soon. Replace the handset on the base phone to

charge.

For optimum performance, charge the battery for a full 12 hours.

Note that during the first 10 - 15 minutes of charging, the phone will be

inactive, i.e., unable to make or receive a call.

After this initial 10 - 15 minutes, you may be able to use the phone, but

the battery duration will be very short; thus it is recommended that

you fully charge the battery before the next usage.

Making calls through the speakerphone

Press (SPEAKERPHONE) on the base phone.

The SPEAKERPHONE lamp and the

LINE lamp light up.

Dial the phone number.

When you are done talking, press

(SPEAKERPHONE) again.

continued

Additional tasks

Put a call on hold

Adjust the speaker volume

Switch to tone dialing

temporarily

Switch to another call

(“call waiting” service*)

* You need to subscribe to the service from your telephone company.

Do this

Press (HOLD).

The LINE lamp flashes slowly.

Press (SPEAKERPHONE) to resume the conversation.

Slide the VOLUME control.

Press (*TONE) while using the telephone after

you’re connected.

The line remains in tone dialing until disconnected.

Press (FLASH) to access the flash function.

Press (FLASH) again to return to he first caller.

Basics

Making calls (continued)

To obtain the best speakerphone performance

• You may not be able to hear the other party’s voice in a noisy place.

Therefore, use the speakerphone in a quiet room.

• Do not bring your hand or other object too close to the microphone

or you will hear a shrill noise (“feedback”).

• When the speaker volume is loud, or the telephone has been placed

close to a wall, you may find that the volume drops suddenly. This is

due to a circuit in the telephone designed to protect against

feedback. In such cases, lower the speaker volume slightly.

Redialing

On the handset

1 Press (TALK).

The TALK/BATT LOW lamp lights up. The dialing keys

light up for 10 seconds.

2 Press (REDIAL/PAUSE) to redial the number last dialed.

On the base phone

1 Press (SPEAKERPHONE).

The SPEAKERPHONE lamp lights up.

2 Press (REDIAL/PAUSE) to redial the number last dialed.

Note

If the number last dialed exceeds 32 digits, only the first 32 digits are dialed.

Tip

The number to be redialed is the last number dialed either on the handset or on

the base phone.

Basics

Basics 17

Receiving calls through the speakerphone

When the phone rings, press

(SPEAKERPHONE) on the base phone.

The SPEAKERPHONE lamp and the

LINE lamp light up.

To adjust the speaker volume, slide the

VOLUME control.

When you are done taking, press

(SPEAKERPHONE) again.

To obtain the best speakerphone

performance, see page 16.

To adjust the ringer volume, see page 22.

LINE lamp

(SPEAKERPHONE)

VOLUME

control

(FLASH)

(*TONE)

SPEAKERPHONE

lamp

(HOLD)

1 When you hear the phone ring;

•Press (TALK)

(or any key except (OFF)) .

•Pick up the handset from the

base phone when the handset

is placed on the base phone.

The TALK/BATT LOW lamp on

the handset and the LINE lamp

on the base phone light up.

The dialing keys light up for 10

seconds.

2 When you’re done talking, press

(OFF) or replace the handset on

the base phone.

The TALK/BATT LOW lamp on

the handset and the LINE lamp

on the base phone go off.

Receiving calls

Put a call on hold

Select a better channel

Adjust the handset volume

Switch to tone dialing

temporarily

Switch to another call

(“call waiting” service*)

Turn on/off the ringer

of the handset

* You need to subscribe to the service from your telephone company.

Additional tasks

Do this

Press (HOLD).

The TALK/BATT LOW lamp flashes slowly.

Press (TALK) to resume the conversation.

Press (CHANNEL).

Set the VOL switch to H (high), M (middle) or L (low).

Press (*TONE) while using the telephone after you’re connected.

The line remains in tone dialing until disconnected.

Press (FLASH) to access the flash function.

Press (FLASH) again to return to the first caller.

See “Setting the ringer type” on page 21.

(*TONE)

TALK/BATT

LOW lamp

VOL

switch

(HOLD)

(FLASH)

(CHANNEL)

Telephone Features

Speed dialing

You can dial with a touch of a few buttons by storing a phone number

on a dialing key. You can store up to 10 different phone numbers

separately on the handset and on the base phone.

Storing phone numbers on the handset

1 Press (PGM).

The TALK/BATT LOW lamp

flashes.

The dialing keys light up for 10

seconds.

2 Press one of the dialing keys

((0) to (9)) for the phone

number to be stored.

You’ll hear a confirmation beep.

3 Enter the phone number you

want to store.

You can enter up to 16 digits,

including a tone and a pause,

each of which is counted as one

digit.

4 Press (PGM) again.

You’ll hear a confirmation beep,

and the number is stored. The

TALK/BATT LOW lamp goes

off.

Notes

• In step 3, if you don’t enter the phone number, the previously stored number

will be erased.

• Do not allow more than 20 seconds to elapse between each step of the

procedure.

• Before storing phone numbers, make sure the handset is not in use.

Tips

• If you enter a wrong number, press (OFF), then start from the beginning.

• Use the supplied directory to write down what you stored on the speed

dialing numbers.

Telephone Features

(REDIAL/PAUSE)

TALK/BATT

LOW lamp

(SPEED DIAL)

(OFF)

(TALK)

Telephone Features

Storing phone numbers on the base phone

1 Press (PGM).

The SPEAKERPHONE lamp

flashes quickly.

2 Press one of the dialing keys

((0) to (9)) for the phone

number to be stored.

You’ll hear a confirmation beep.

3 Enter the phone number you

want to store.

You can enter up to 16 digits,

including a tone and a pause,

each of which is counted as one

digit.

4 Press (PGM) again.

You’ll hear another

confirmation beep, and the

number is stored.

Notes

• In step 3, if you don’t enter the phone number, the previously stored number

will be erased.

• Do not allow more than 20 seconds to elapse between each step of the

procedure.

• You cannot store phone numbers on the base phone while the handset is

being used. The LINE lamp will light up to indicate this condition.

Tips

• If you enter a wrong number, press (PGM), then start from the beginning.

• Use the supplied directory to write down what you have stored to the speed

dialing numbers.

continued

(REDIAL/PAUSE)

SPEAKERPHONE

lamp

LINE lamp

(SPEAKERPHONE)

(SPEED DIAL)

Telephone Features

Speed dialing (continued)

To store the previous number dialed

Press (REDIAL/PAUSE) directly after step 2, then go to step 4.

To store a number to be dialed via Private Branch Exchange (PBX)

Before entering a phone number in step 3 on the previous page, do as

follows:

1 Enter the outside line access digit (e.g. 9).

2 Press (REDIAL/PAUSE).

To change a stored number

To store a new number, follow the instructions described previously.

To clear a number from memory

1 Press (PGM).

2 Press the speed dialing key you want to clear.

3 Press (PGM) again.

Making calls with speed dialing on the handset

1 Press (TALK).

The TALK/BATT LOW lamp lights up. The dialing keys light up for 10

seconds.

2 Press (SPEED DIAL).

3 Enter the desired speed dialing number ((0) to (9)).

The phone number stored in the speed dialing number will be dialed.

Making calls with speed dialing on the base phone

1 Press (SPEAKERPHONE).

The SPEAKERPHONE lamp lights up.

2 Press (SPEED DIAL).

3 Enter the desired speed dialing number ((0) to (9)).

The phone number stored in the speed dialing number will be dialed.

La page charge ...

Sony Cordless Telephone SPP-934 Manuel utilisateur

Marque: Sony

Modèle: Cordless Telephone SPP-934

Catégorie: Téléphones

Taper: Manuel utilisateur

Ce manuel convient également à

SPP-934

Télécharger le PDF

rapport

dans d''autres langues

English: Sony Cordless Telephone SPP-934 User manual

Sony Cordless Telephone SPP-934 Manuel utilisateur

Ce manuel convient également à

Sony Cordless Telephone SPP-934 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents