NAPOLEON NERV2400T Manuel utilisateur

Marque: NAPOLEON

Modèle: NERV2400T

Taper: Manuel utilisateur

Model NERV2400T

This product earned the ENERGY STAR

meeting strict energy efficiency guidelines set by

Natural Resources Canada and the US EPA. It

meets ENERGY STAR requirements only when

used in Canada.

24294 rev. 01

READ AND SAVE THESE INSTRUCTIONS

⚠RESIDENTIAL USE ONLY⚠

VB0185

ABOUT THIS UNIT

1. The only main wall control compatible with this unit is the X-Touch.

2. The terminal connectors for this unit are already mounted to the electronic board.

USER AND INSTALLER MANUAL

Please take note that this manual uses the following symbols to emphasize particular information:

Identifies an instruction which, if not followed, might cause serious personal injuries including possibility of death.

CAUTION

Denotes an instruction which, if not followed, may severely damage the unit and/or its components.

NOTE: Indicates supplementary information needed to fully complete an instruction.

LIMITATION

For residential (domestic) installation only. Installation work and electrical wiring must be done by a qualified person in accordance with all

applicable codes and standards, including fire-rated construction codes and standards.

⚠WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSON(S) OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer.

2. Before servicing or cleaning this unit, disconnect the power cord from the electrical outlet.

3. This unit is not designed to provide combustion and/or dilution air for fuel-burning appliances.

4. When cutting or drilling into a wall or ceiling, do not damage electrical wiring and other hidden utilities.

5. Do not use this unit with any solid-state speed control device other than those specified in sections 2 and 3.

6. This unit must be grounded. The power supply cord has a 3-prong grounding plug for your personal safety. It must be plugged into a

mating 3-prong grounding receptacle, grounded in accordance with the national electrical code and local codes and ordinances.

Do not remove the ground prong. Do not use an extension cord.

7. Do not install in a cooking area or connect directly to any appliances.

8. Do not use to exhaust hazardous or explosive materials and vapors.

9. When performing installation, servicing or cleaning this unit, it is recommended to wear safety glasses and gloves.

10. When applicable local regulation comprises more restrictive installation and/or certification requirements, the aforementioned

requirements prevail on those of this document and the installer agrees to conform to these at his own expenses.

11. Due to the weight of the unit, two installers are recommended to perform installation

CAUTION

1. To avoid prematurely clogged filters, turn the unit OFF during construction or renovation.

2. Please read specification label on product for further information and requirements.

3. Be sure to duct air outside – Do not intake/exhaust air into spaces within walls or ceiling or into attics, crawl spaces, or garage.

Do not attempt to recover the exhaust air from a dryer or a range hood.

4. Intended for residential installation only in accordance with the requirements of NFPA 90B (for a unit installed in U.S.A.) or Part 9 of

the National Building Code of Canada (for a unit installed in Canada).

5. Do not run any air ducts directly above or within 2 ft (0.61 m) of a furnace or its supply plenum, boiler, or other heat-producing

appliances. If a duct has to be connected to the furnace return plenum, it must be connected 10’ (3.1 m) away from plenum’s

connection to the furnace.

6. The ductwork is intended to be installed in compliance with all applicable local and national codes.

7. When leaving the house for a long period of time (more than two weeks), a responsible person should regularly check if the unit

operates adequately.

8. If the ductwork passes through an unconditioned space (e.g.: attic), the unit must operate continuously except when performing

maintenance and/or repair. Also, the ambient temperature of the house should never drop below 18°C (65°F).

9. At least once a year, the unit mechanical and electronic parts should be inspected by qualified service personnel.

10. Do not use your unit during construction or renovation of your house or when sanding drywall. Certain types of dust and vapors

may damage your ventilation system.

11. During winter, make sure that the outside intake and exhaust hoods are free from any snow. During a big snow storm, check that

your unit doesn’t draw in any snow. If it does, turn the unit OFF for a few hours.

12. Since the electronic control system of the unit uses a microprocessor, it may not operate correctly because of external noise or very

short power failure. If this happens, unplug the unit and wait approximately 10 seconds. Then, plug the unit in again.

⚠WARNING

For the User

1. USING THIS UNIT

CAUTION

Before using this unit for the first time, please take the time to carefully read page 2 of this guide to ensure it is

used safely and properly.

This unit performs a 30-second booting sequence at startup. Your main wall control indicates the progression of the booting sequence in

percentage. No command will be taken until the unit is fully booted.

You can control your unit using one main wall control, and up to five optional 20-minute push buttons,

usually located in bathrooms.

Activation of a 20-minute push button overrides the current operation mode of the unit, including defrost

cycles, and a timer icon will appear on the main control screen. This icon disappears when the 20-minute

push button activation cycle is done.

2. X-TOUCH MAIN WALL CONTROL

VC0166

% HUM

TURBO

MODE

% HUM

key

LCD screen.

Backlight: If the

backlight is not lit, the

first key pressed (no

matter which key) will

turn on the backlight.

The backlight remains

on for 10 seconds after

the last key is pressed.

MODE

key

TURBO

function key

STANDBY

mode*

* STANDBY mode is the factory set default mode. When the unit

is on standby mode, it will only respond to override wall control

(if present). Only the house icon appears on LCD screen. On

other operation modes, the house icon is still there, and the label

mode in which the unit operates appears at right of LCD screen.

MODE



Press the Mode key to choose the operation mode

of the ventilation unit (except TURBO mode).

Operating Mode will then appear on LCD screen

(STANDBY, RECIRC, 20 min/h, CONT, SMART).

STANDBY

Put the unit on stand-by mode, so it will only

respond to override wall controls (if present). On

LCD screen, only the House is visible showing the

control is powered on.

RECIRC

Air is recirculated inside the house on high

speed.

20 MIN/H

The unit exchanges air intermittently on a one hour

cycle as follows: OFF for 40 min. (or recirculation

for 40 min. on low or high speed, see section 10)

and then exchange air during 20 min. on low speed.

Repeat cycle after the 20 min. of air exchange.

CONT

Air is exchanged with the outdoors at the minimum

blower speed.

CONT

OPERATING MODES

SMART

Air exchange is managed according to indoor humidity measured

by the wall control and outdoor temperature. In SMART mode, the

SMART icon appears as well as the current operating mode called

by SMART (see below).

CONT

TURBO

TURBO mode

called by

SMART mode

CONT mode

called by

SMART mode

20 min/h mode

called by

SMART mode

ECO mode

called by SMART

mode (see NOTE)

STANDBY mode

called by

SMART mode

NOTE: The ECO mode set the unit operation to Standby for

50 minutes (or in recirc mode for 50 minutes; see section 10)

and then exchange air during 10minutes on low speed.

This mode is exclusively activated by SMART mode.

The chart below shows the operating modes called by SMART

mode, according to the indoor humidity percentage and the

outdoor temperature.

From -35°C

to -25°C

From -25°C

to -15°C

From -15°C

to -5°C

From -5°C

to 5°C

From 5°C

to 15°C

From 15°C

to 25°C

From 25°C

to 35°C

80%

70%

60%

50%

30%

20%

40%

CONT

TURBO

VG0100A

OUTDOOR TEMPERATURE

INDOOR HUMIDITY LEVEL

* This area represents STANBY mode.

CONT

VQ0137

For the User

2. X-TOUCH MAIN WALL CONTROL (CONT’D)

The TURBO icon is flashing during the 4-hour

cycle. To exit this function before the end of its

4-hour cycle, press on TURBO or MODE key; the

unit will get back to its previous operation mode.

TURBO

TURBO FUNCTION

TURBO



Press the TURBO function key to turn the unit on

air exchange in high speed during 4 hours, then,

the unit will get back to its previous operation

mode.

3 sec.

The TURBO icon appears and stay continuously.

To exit this TURBO mode, press on TURBO or

MODE key; the unit will get back to its previous

operation mode.

Press and hold the TURBO function key during

3 seconds to turn the unit on air exchange in high

speed continuously.

DEHUMIDISTAT FUNCTION

CONT

The dehumidistat function has been created

to manage the indoor relative humidity excess.

When the actual home Relative Humidity

percentage (RH %) detected is over the set value,

drops appears on screen and the control overrides

the current mode,

turning on the unit on high

speed exhange

until the indoor relative humdity %

set is reached. The unit then returns to its previous

operation setting. Refer below to find out how to

set the indoor relative humidity %.

TURBO



In all modes except

STANDBY and SMART,

press the % HUM key

to enable the

dehumidistat function.

CONT

The actual

home RH %

level appears

on screen

(enabled).



% HUM

HOW TO ENABLE AND DISABLE THE DEHUMIDISTAT FUNCTION:

CONT

Press once more

on the % HUM

key to disable

the dehumidistat

function.

The actual

home RH%

level disappears

from screen

(disabled).



% HUM

3. 20-MINUTE PUSH BUTTON AUXILIARY CONTROL

VC0127

• Press once to activate air exchange on high speed for 20 minutes; the indicator will flash.

• To stop activation before the end of the 20-minute cycle, push one more time. Unit then returns to its to

previous setting.

After a power failure, the 20-minute cycle will be erased.

PROTECTION MODE INDICATOR

This icon appears to show when the ventilation unit is in

Protection Mode. This special mode has been created

to protect the ventilation unit from specific conditions

(e.g.: outdoor temperature colder than -25°C). There

is no action to be taken when this icon appears, it will

disappear by itself.

For the User

4. USER SERVICING INSTRUCTIONS

This unit requires seasonal and annual maintenance. Your main wall control includes a maintenance reminder

that lights up 4 times a year.

4.1 SEASONAL MAINTENANCE

1. Unplug the unit.

2. Undo both door latches and open the door.

3. Slide out both filters from the top of the recovery core.

4. Wash the filters with a mild soap and lukewarm water, rinse thoroughly and allow to dry completely.

5. Reinstall the filters in the unit.

6. Close the door and plug unit back. The unit will perform a 30-second booting sequence and will resume operating as previously set.

7. Reset the maintenance indicator by holding both the MODE and TURBO keys for 3 seconds.

4.2 ANNUAL MAINTENANCE

1. Perform steps 1 and 2 from seasonal maintenance.

2. Slide both filters and the core out of the unit.

3. Clean the inside of the unit with a clean damp cloth and wipe dry.

4. Wash the filters with a mild soap and lukewarm water, rinse thoroughly and allow to dry completely.

5. To clean the recovery core, remove the dust on the core using a vacuum cleaner and a soft brush attachment.

CAUTION

Do not soak the energy recovery core.

6. Reinstall the core back into the unit.

7. Reinstall the filters back on the core.

8. Close the unit’s door.

9. Clean the exterior hoods.

10. Plug the unit back. The unit will perform a 30-second booting sequence and will resume operating as previously set.

11. Reset the maintenance indicator by holding both the MODE and TURBO keys for 3 seconds.

CONT

VQ0134

Maintenance icon

For the User

Contact customer service at 1-866-820-8686 for any unresolved issue.

5. USER’S TROUBLESHOOTING

Before trying any of the following, first try unplugging the unit and plugging it back. If the issue is not solved, refer to the table below.

PROBLEM TRY THIS

1. Nothing works. • Make sure that the unit is plugged in.

• Make sure that the unit is receiving power from the house circuit breaker or fuse.

2. An error code starting with

E0 (E01, E02, etc.) is dis-

played on the wall control.

• Make sure that the color coded wires have been connected to their appropriate place.

• Make sure that the wires are correctly connected.

• Press simultaneously and hold for 10 seconds the % HUM, MODE and TURBO keys to reset the wall

control. The user preferences will have to be reset.

3. An error code starting with

E2 (E21, E22, etc.) is dis-

played on the wall control.

• Problem with the ventilation unit. Contact your installer.

4. A 10-second countdown

is displayed on the wall

control.

• Wait for the end of the countdown without pressing any key.

5. The snowflake icon is

flashing on the wall control

screen.

• The ventilation unit is in Protection mode; it will get out of this mode by itself.

• If this situation occurs regularly, or when outdoor temperature is higher than -20°C, contact your

installer.

6. Condensation on windows

(air too humid).

• Operate the unit on TURBO or CONT mode until the situation is corrected.

• Leave curtains half-open to allow air circulation.

• Store all firewood in a closed room with a dehumidifier or in a well ventilated room, or store the wood

outdoors.

• Do not adjust the thermostat of your heating system below 18°C (64°F).

7. Inside air too dry. • Temporarily use a humidifier.

• Operate the unit in 20 min/h mode or in RECIRC. mode.

8. Air too cold at the air sup-

ply grille.

• Make sure that the exterior hoods are not blocked.

• Operate the unit in 20 min/h mode or in RECIRC. mode.

• Install a duct heater.

9. The main wall control does

not work.

• The 30-second boot sequence is not completed. See Section 1 on page 3.

• A 20-minute push button auxiliary control is in use. See Section 1 on page 3.

• The protection mode overrides the main control operation (snowflake icon). See page 4.

For the User

6. WARRANTY

This unit is a high-quality product, built and packaged with care. The manufacturer warrants to the original purchaser of its product,

that such product will be free from defects for the period stated below, from the date of original purchase. For all units, the warranty

covers parts only against any operational defect. This is a 5-year warranty. Subject to performing the core maintenance according to the

recommendations in this manual, the energy recovery core (ERV) has a 10-year warranty. If any defect should occur, we urge you to read

the user and installer manual carefully. If the problem persists, observe the following rules:

RULES TO FOLLOW

If the unit is defective, contact your ventilation contractor (see address on your user and installer manual cover page). The contractor will

determine with you the reason for the defect, and if needed, do the replacement or repair. If ever it is impossible to reach your ventilation

contractor, call 1-866-820-8686; the personnel will be pleased to give you the phone number of a distributor or a service center near you.

REPLACEMENT PARTS AND REPAIR

In order to ensure your ventilation unit remains in good working condition, you must use the manufacturer’s genuine replacement parts

only. The manufacturer’s genuine replacement parts are specially designed for each unit and are manufactured to comply with all the

applicable certification standards and maintain a high standard of safety. Any third party replacement part used may cause serious

damage and drastically reduce the performance level of your unit, which will result in premature failing. The manufacturer also recommends

contacting a service depot certified by the manufacturer for all replacement parts and repair.

BILL OF PURCHASE

No replacement or repair covered by the warranty will be carried out unless the unit is accompanied by a copy of the original bill of

purchase. Please retain your original.

MISCELLANEOUS COSTS

In each case, the labor costs for the removal of a defective part and/or installation of a compliant part will not be covered by

the manufacturer.

CONDITIONS AND LIMITATIONS

These units are created for residential use only and must be used in a building as defined below:

Building: All structures zoned and/or erected for the act, process or art of human or animal habitation and/or the storage or

warehousing of goods.

Residential use: Dwelling, lodging, suite: Building, or part of a building, intended to act as either the domicile to one or several people

which can include general sanitary, food consumption and rest facilities. Buildings of only one room or a group of

rooms including those occupied by a tenant or owner; comprise the lodgings, the individual rooms of the motels,

hotels, rooming/lodging houses, boarding/half-way/foster homes, dormitories, and suites, as well as the stores and the

business establishments constituted by only one room in a dwelling.

Commercial use: Agricultural establishment, commercial establishment for assembly, care, or detention: Building or part of a building that

does not contain a dwelling, situated on land dedicated to agriculture or farming and used primarily to shelter animals,

or for the production, the storage or the treatment of agricultural or horticultural products or animal food. Building or

part of a building, used for the display or retail of goods, professional or personal services, or commodities. Building,

or part of a building used by persons gathering for civic activities, religious or political assembly, tourism, educational/

vocational training, recreation or the consumption of food or drink. Building, or part of a building used to shelter persons

of impaired physical or psychological states, persons requiring palliative care or medical treatments, or persons for

reasons out of their control, cannot escape harm or threat of danger autonomously.

Industrial use: Building, or part of a building, used for the assembly, the manufacture, the creation, the treatment, the repair or the

storage of products and combustible materials and that contain fuels that when ignited or exploded in sufficient quantity

may constitute a risk of fire.

The above warranty applies to all cases where the damage is not a result of poor installation, improper use, mistreatment or negligence,

acts of God, or any other circumstances beyond the control of the manufacturer. Furthermore, the manufacturer will not be held

responsible for any bodily injury or damage to personal property or real estate, whether caused directly or indirectly by the unit. This

warranty supersedes all prior warranties.

For the Installer

CAUTION

Before installing this unit, please take the time to carefully read page 2 of this guide to ensure it is installed safely

and properly.

7. INSTALLATION

7.1 LOCATING THE UNIT

Choose an appropriate location for the unit:

• So as to provide easy access to the interior cabinet for quarterly and annual maintenance. Plan for a 27-in. clearance in front of

the unit for the door to open. If that is not possible, an 18-in. clearance is acceptable, in which case the door will have to be removed

for maintenance to be performed.

• Within an area of the house where the ambient temperature is kept between 18°C (65°F) and 40°C (104°F).

• Close to an exterior wall, so as to limit the length of the insulated flexible duct to and from the unit.

• Away from hot chimneys, electrical panel and other fire hazards.

• Allow for a power source (standard outlet) within 3 feet.

• Close to a drain. If no drain is close by, use a pail to collect run-off.

7.2 MOUNTING THE UNIT

CAUTION

Always make sure that the unit is level.

7.2.1 USING CHAINS AND SPRINGS

The unit can be hung using the provided chains and springs:

VD0378

For the Installer

7.2.2 USING THE WALL BRACKETS

1. Trace a level line on the wall, approximately where the top of the unit will be.

2. Using the provided 1.5-in. screws and washers, install the longest of both brackets to the wall making sure to secure it to all of the

available studs.

⚠WARNING

The bracket must not be secured to the drywall only.

4. Using the provided 1.5-in. screws, assemble both spacers to the lower corners of the back of the unit.

5. Using the provided 3/8-in. screws, mount the two other brackets to the top back of the unit, as illustrated below. Do not use an

electric screw driver.

6. Hang the unit to the bracket on the wall, and secure the smallest bracket to the wall, into a stud if possible.

7.3 INSTALLING THE DUCTWORK AND THE REGISTERS

⚠WARNING

• Never install a stale air exhaust register in a closed room where a combustion device operates, such as a gas

furnace, a gas water heater or a fireplace.

• When performing duct connections, always use approved tools and materials. Respect all corresponding laws

and safety regulations. Please refer to your local building code.

7.3.1 FULLY DUCTED SYSTEM

Stale air from building ductwork:

• Install registers in areas where contaminants are produced: Kitchen,

bathrooms, laundry room, etc.

• Install registers on an interior wall, 6 to 12 inches (152 to 305 mm) away

from the ceiling OR install them in the ceiling.

• Install the kitchen register at least 4 feet (1.2 m) away from the range.

Fresh air to building ductwork:

• Install registers in bedrooms, dining room, living room and basement.

• Install registers either in the ceiling or high on the walls with the airflow

directed towards the ceiling.

• If a register must be installed in the floor, direct the air flow up the wall.

VO0288

VH0156

1010

For the Installer

7.3.2 EXHAUST DUCTED SYSTEM - SUPPLY SIDE

CAUTION

When performing duct connections to the furnace supply duct, use

metal ducts appropriately sized to support the additional airflow

produced by the unit.

Stale air from building ductwork:

• Install registers in areas where contaminants are produced: Kitchen, bathrooms,

laundry room, etc.

• Install registers on an interior wall, 6 to 12 inches (152 to 305 mm) away from the

ceiling OR install them in the ceiling.

• Install the kitchen register at least 4 feet (1.2 m) away from the range.

Fresh air to building ductwork:

• Cut an opening into the furnace supply duct at least 18 inches (0.5 m) away from

the furnace.

• Connect this opening to the fresh air to building port of the unit (use metal ducts,

see illustration at right).

• Make sure that the unit duct forms an elbow inside the furnace ductwork.

NOTE: For this type of installation, it is recommended, however, not essential, that

the furnace blower be synchronized with the unit.

7.3.3 EXHAUST DUCTED SYSTEM - RETURN SIDE

Stale air from building ductwork:

• Install registers in areas where contaminants are produced: Kitchen, bathrooms,

laundry room, etc.

• Install registers on an interior wall, 6 to 12 inches (152 to 305 mm) away from the

ceiling OR install them in the ceiling.

• Install the kitchen register at least 4 feet (1.2 m) away from the range.

Fresh air to building ductwork:

• Cut an opening into the furnace return duct at least 10 feet (3.1 m) away from

the furnace (A+B).

• Connect this opening to the fresh air to building port of the unit (see illustration

at right) using metal ducting.

NOTE : For this type of installation, it is recommended, however, not essential, that

the furnace blower be synchronized with the unit.

7.3.4 SIMPLIFIED INSTALLATION - RETURN/SUPPLY

Stale air from building ductwork:

• Cut an opening into the furnace return duct at least 10 feet (3.1 m) (A + B) away

from the furnace.

• Connect this opening to the stale air from building port of the unit (as illustrated).

Fresh air to building ductwork:

CAUTION

When performing duct connections to the furnace supply duct, use

metal ducts appropriately sized to support the additional airflow

produced by the unit.

• Cut an opening into the furnace supply duct at least 18 inches (0.5 m) away from

the furnace.

• Connect this opening to the fresh air to building port of the unit (use metal ducts,

see illustration at right).

• Make sure that the unit duct forms an elbow inside the furnace ductwork.

NOTE: For this type of installation, it is recommended, however, not essential, that

the furnace blower be synchronized with the unit.

VH0157

18” (0.5 M)

MINIMUM

VH0158

VH0159

18” (0.5 M)

MINIMUM

A + B = AT LEAST

10’ (3.1 M)

1111

For the Installer

7.3.5 SIMPLIFIED INSTALLATION - RETURN/RETURN

Fresh air to building ductwork:

• Cut an opening into the furnace return duct at least 10 feet (3 m) away from the

furnace.

• Connect this opening to the fresh air to building port of the unit (use metal ducts,

see illustration at right).

Stale air from building ductwork:

• Cut an opening into the furnace return at least 3 feet (1 m) ahead of the fresh air

to building ductwork connection to the furnace return.

• Connect this opening to the stale air from building port of the unit.

• Make sure that both connections to the furnace return duct are at least 3feet

(1m) apart.

CAUTION

For this type of installation, the furnace must always be synchronized

with the unit. See section 9.

7.4 CONNECTING THE DUCTS TO THE UNIT

CAUTION

• If ducts have to go through an unconditioned space (e.g.: attic), always use insulated ducts.

• Make sure the vapor barrier on the insulated ducts does not tear during installation to avoid condensation

within the ducts.

• Always use insulated ducts to connect the Fresh air from outdoors and Stale air to outdoors ports with the

exterior hoods.

7.4.1 INSULATED FLEXIBLE DUCTS

1. Pull back the insulation to expose the flexible duct.

2. Attach the flexible duct to the port using tie wrap.

3. Pull the insulation over the joint and tuck in between the inner and outer rings of the double collar.

4. Pull down the vapor barrier (shaded part in illustrations below) over the outer ring to cover it completely. Fasten in place the vapor

barrier using the port strap (included in unit parts bag). To do so, insert one collar pin through the vapor barrier and first strap hole,

then insert the other collar pin through the vapor barrier and center strap hole and close the loop by inserting the first collar pin in the

last strap hole.

7.4.2 NON-INSULATED FLEXIBLE DUCTS

Use tie wraps to perform connections, then seal with duct tape.

7.4.3 NON-INSULATED RIGID DUCTS

To avoid transmission of vibrations, always use a 6-inch section of flexible duct to connect rigid ducts to the unit. Use tie wraps to perform

connections, then seal with duct tape.

COLLAR PINS

STRAP

VJ0132



VH0160

1212

For the Installer

7.5 INSTALLING THE EXTERIOR HOODS

Refer to illustration at right to connect the insulated duct to the hoods. An “Anti-Gust

Intake Hood” should be installed in regions where a lot of snow is expected to fall.

⚠WARNING

Make sure that both hoods are at least 18 inches above the ground

and that the intake hood is at least 6 feet (1.8m) away from any of

the following:

• Exhaust hood

• Dryer exhaust, high efficiency furnace vent, central vacuum

vent

• Gas meter exhaust, gas barbecue-grill

• Any exhaust from a combustion source

• Garbage bin and any other source of contamination

7.6 CONNECTING THE DRAIN

CAUTION

It is not required to install the included drain tubing. However, it is recommended in climates where the outdoor

temperature can remain below -25°C (-13°F) over a 24-hour period for several days in a row, combined with an

indoor humidity of 40% or higher.

1. Cut 2 sections of plastic tubing of at least 16” each.

2. Connect each one of them to the drain fittings located under the unit.

Remove both drain plugs inside the unit before installing the tubing.

3. Join their other ends to the «T» junction and remaining tubing as illustrated.

This will prevent the unit from drawing unpleasant odors from the drain source.

4. Run the tube to the floor drain or to an alternative drain pipe or pail. If using a

pail to collect water, locate the tube end approximately 1” into the pail in order to

prevent water from being drawn back into the unit.

VD0028

EXHAUST

HOOD

INTAKE

HOOD

18”

(457 MM)

18”

(457 MM)

6” ø

(152 MM)

6’

(1.8 M)

6’

(1.8 M)

18”

(457 MM)

PTIONAL

DUCT

LOCATION

TAPE AND DUCT TIE

CAULKING

VO0273A

16"

(406 mm)

16"

(406 mm)

VD0337A

± 1”

TIE WRAP

LOCATION OF THE DRAIN PLUGS.

VD0387

1313

For the Installer

8. WALL CONTROLS CONNECTION

⚠WARNING

Always disconnect the unit before making any connections. Failure to disconnect power could result in electric

shock or damage to the wall control or electronic module inside the unit.

CAUTION

Failure to comply with the following can cause erratic operation of the unit and/or the wall control:

Never install more than one main wall control per unit. Make sure that the wires do not short-circuit between

themselves or by touching any other components on the wall control. Avoid poor wiring connections. To reduce

electrical interference (noise) potential, do not run wall control wiring next to control contactors or near light

dimming circuits, electrical motors, dwelling/building power or lighting wiring, or power distribution panel.

The terminal blocks needed to connect the wall controls are already installed on the electronic

board. To access them, open the unit’s side panel and remove the terminal blocks from the

electronic board.

Run the wall control wires through the grommet before connecting them to the terminal blocks.

8.1 AUXILIARY WALL CONTROLS

Up to five 20-minute auxiliary wall controls can be installed with this unit.

Proceed as follows to connect the auxiliary wall control cable(s) to the 6-position terminal block:

1. Strip the end of the cable.

2. Strip 1/4" off the end of 3 of the wires.

3. Insert the wires in their corresponding holes. A wire is correctly inserted when its orange receptacle is lower than another one

without wire. On illustration below, wire A is correctly inserted, but wire B is not.

4. Reinstall the terminal block on the electronic board.

VE0353

VE0292

Main

control

Auxiliary

control(s)

Grommet

VE0430

1414

For the Installer

8.2 MAIN WALL CONTROL

The only main wall control compatible with this unit is the X-Touch. Only one main wall control can be installed for each unit.

Proceed as follows to connect the main wall control cable to the 4-position terminal block:

1. Strip the end of the cable.

2. Strip 1/4” off the end of the 4 wires. Do not strip longer than required.

3. Using a small flat blade screwdriver, connect each wire to its corresponding

terminal by referring to the labels on the unit (YELLOW to Y; BLACK to B; RED

to R; GREEN to G).

4. Reinstall the terminal block on the electronic board.

9. ELECTRICAL CONNECTION TO THE FURNACE

⚠WARNING

Never connect a 120-volt AC circuit to the terminals of the furnace interlock (standard wiring). Only use the low

voltage class 2 circuit of the furnace blower control.

For a furnace connected to a cooling system:

On some older thermostats, energizing the “R” and “G” terminals at the furnace has the effect of energizing “Y” at the thermostat and

thereby turning on the cooling system. If you identify this type of thermostat, you must use the ALTERNATE FURNACE INTERLOCK WIRING.

UNIT TERMINAL CONNECTOR

THERMOSTAT

TERMINALS

COOLING SYSTEM

NO C NC I OC OL

WRGY

THERMOSTAT

TERMINAL

4 WIRES

2 WIRES

heating only

FURNACE

24-VOLT

TERMINAL BLOCK

2 WIRES

COOLING SYSTEM

UNIT TERMINAL CONNECTOR

VE0350A

NO C NC I OC OL

WRGY

4 WIRES

2 WIRES

heating only

FURNACE

24-VOLT

TERMINAL BLOCK

2 WIRES

LOW VOLTAGE

CLASS 2

LOW VOLTAGE

CLASS 2

STANDARD FURNACE INTERLOCK WIRING ALTERNATE FURNACE INTERLOCK WIRING

VE0354

1515

For the Installer

10. RECIRCULATION AND DEFROST SETTINGS

CAUTION

Set extended defrost on all units located in climates where the outdoor temperature typically remains below -25°C

(-13°F) (i.e. Winnipeg, Regina, Quebec, Edmonton, Yellowknife, Whitehorse, Labrador City) over a 24-hour period

for several days in a row, combined with an indoor humidity of 40% or higher.

Press and hold the

MODE key for 3 seconds.

MODE



3 sec.

Two lines are

flashing to show

Standby (default

configuration setting).

The LCD screen will show one of these configurations:

CONT

Recirculation arrows

are turning, rE

flashes and CONT

label appears to show

RECIRCULATION on

low speed.

TURBO

Recirculation arrows

are turning, rE

flashes and TURBO

label appears to show

RECIRCULATION on

high speed.

MODE



TURBO



Use MODE or TURBO key

to see all 3 configurations.



% HUM

Press % HUM key to accept chosen

configuration and go to setting defrost

cycle type.

The LCD screen will show one of these defrost cycle types:

Sd (Standard)

(factory defrost cycle setting).

When needed, the unit will

perform defrost cycle on high

speed.

NOTE: This is the defrost type

used for the data published by

HVI and ENERGY STAR®.

PL (Plus)

Use this cycle in cold regions

(outdoor temperature -25°C

[-13°F] and lower). When

needed, the unit will perform

defrost cycle on high speed

on a longer period of time.

dI (Discretion)

When needed, the defrost

cycle will be performed on

the same speed than the unit

ventilation speed. (e.g.: if the

unit is set on TURBO, the

defrost cycle will be done on

high speed, and if the unit is

set on CONT, the defrost cycle

will be done on low speed.

MODE



TURBO



Use MODE or TURBO key

to see all 3 defrost cycle type.



% HUM

Press % HUM key to accept chosen

defrost cycle type and go to software

version display

LCD screen alternates between the house with circled

arrows and the house without arrow. The numbers under

the house are the software version number.

Press % HUM key OR

wait 10 seconds to exit

user setting menu.



% HUM

1616

For the Installer

11. BALANCING THE UNIT

11.1 B

EFORE STARTING

What you need to balance the Unit:

• One X-Touch main wall control close to the unit.

• A magnehelic gauge capable of measuring 0 to 1 inch of water (0 to 250 Pa) and 2 plastic tubes.

• The balancing chart and preset speeds table of the unit; affixed on the unit, behind the small control panel.

Before balancing the unit:

• Seal all the unit ductwork with tape. Close all windows and doors.

• Turn off all exhaust devices such as range hood, dryer and bathroom fans.

• Make sure all filters are clean (if it is not the first time the unit is balanced).

NOTE: Make sure that the furnace/air handler blower is ON if the installation is in any way connected to the ductwork of the cold air

return. If not, leave furnace/air handler blower OFF.

Installing the magnehelic gauge:

1. Place the magnehelic gauge on a level surface and adjust it to zero.

2. According to the airflow to be measured, connect tubing from gauge to STALE

air flow or FRESH air flow pressure taps (see illustration at right).

3. Be sure to connect the tubes to their appropriate high/low fittings. If the gauge

drops below zero, reverse the tubing connections.

Balancing Chart and Preset Speeds Table

Use the balancing chart on the unit to convert pressure (in. w.g.) values read by the magnehelic gauge to airflow (CFM) values. While

balancing, the X-Touch wall control screen shows which pressure taps have to be used. Keep in mind that a difference between flows up

to ±10cfm is acceptable. See example below.

HIGH

LOW

FRESH AIR FLOW

HIGH

LOW

STALE AIR FLOW

VP0027A

Plug magnehelic gauge

tubing to STALE airflow.

Plug magnehelic gauge

tubing to FRESH airflow.

FLOW FRESH STALE

CFM IN. W.G. IN. W.G.

120 0.71 0.73

125 0.67 0.70

130 0.63 0.67

135 0.59 0.64

140 0.55 0.61

145 0.51 0.58

150 0.47 0.55

UNIT BALANCING CHART

STALE reading value with

its corresponding CFM

FRESH reading value with

its corresponding CFM

1717

For the Installer

11.2 BALANCING THE UNIT

B Connect an X-Touch main wall control to the unit. The control has to be close to the unit.

GENERAL INFORMATION ABOUT X-TOUCH WALL CONTROL USAGE IN UNIT BALANCING PROCEDURE

% HUM

TURBO

MODE

Press on MODE

key to raise the value.

Press on % HUM

key to accept.

Press on TURBO

key to lower the value.

TURBO

This label section shows which speed is

being set (e.g.: TURBO).

Arrow shows where to install the

magnehelic gauge tubing

(e.g.: EXHAUST).

Motor speed indicator.

PROG flashes on screen as long as you

are in Program Mode Setting menus (preset

speeds or custom speeds). It disappears

from screen when all settings are done or

when there is no change after 60 seconds.

Press and hold both

% HUM and TURBO

keys for 10 seconds.

% HUM



TURBO



AND

10 sec.

PROG start flashing.

A 10-second

countdown appears.

% HUM

MODE

TURBO



Press any key to enter

program mode. If there

is no key pressed before

the end of the countdown,

the unit will go back to its

previous mode.

Enter Program Mode.

Choose between two options: • 01, 02, etc.: Preset speeds (balance the unit only, faster option)

•

_ _: Custom speeds (adjust TURBO speed and balance the unit, then set CONT,

20-min. push-button control and RECIRC speeds).

Select the Preset speeds or Custom speeds.

Press on MODE key to

raise the value.

Press on TURBO key to

lower the value.



% HUM

Press % HUM key

to accept chosen

preset speed.

MODE



TURBO



NOTE: From 01 value, pressing on TURBO key will access to custom speed settings (see page 19).

01 speed value

(preset value) will

appear on screen.

Write selected

preset speed

on label affixed

on the unit for

future reference.

E Connect the magnehelic tubings to the unit (see 11.1).

1818

For the Installer

If the unit speed is set close to its highest speed, we recommend to first measure and note both airflows.

Refer to the unit balancing chart to find the corresponding CFMs.

Determine which airflow should be adjusted (the higher airflow must be lowered to equalize the lower one).

See example below.

Pressure

in. w.g.

Fresh

CFM

Stale

CFM

0.31 152 155

0.32 156 159

0.33 159 162

0.34 162 166

0.35 165 169

0.36 168 172

0.37 171 176

0.38 174 179

0.39 177 183

0.40 180 186

0.41 183 189

0.42 186 193

0.43 189 196

0.44 193 200

0.45 196 203

0.46 199 206

0.47 202 210

0.48 205 213

0.49 208 217

0.50 211 220

0.51 214 223

0.52 217 227

0.53 220 230

0.54 223 234

0.55 226 237

STALE reading

value with its

corresponding

CFM

FRESH reading

value with its

corresponding

CFM

In that case, the FRESH

airflow must be lowered

to reach the STALE

airflow value.

NOTE: At first airflow readings, for speed value 01, both stale and fresh airflow

values displayed on control screen are 100%.

TURBO

Before airflow adjustment

After airflow adjustment

TURBO

STALE airflow

reading:

0.41 in. w.g.,

189 CFM

FRESH airflow

reading:

0.50 in. w.g.,

211 CFM

STALE airflow

reading:

0.41 in. w.g.,

189 CFM

FRESH airflow

reading:

0.43 in. w.g.,

189 CFM

NOTE: The following shown values are example. The real values vary according to the preset speed chosen, the unit

installation, etc.

Adjust stale air TURBO speed (or press % HUM key to keep it as is).

TURBO

Press % HUM key

to accept chosen

percentage.



% HUM

Press on MODE key to

raise the value.

Press on TURBO key to

lower the value.

MODE



TURBO



Take the reading

from stale airflow

pressure taps.

Check the magnehelic

gauge along with the unit

balancing chart until the

desired airflow is reached.

Write selected

airflow percentage

on label affixed on

the unit for future

reference.

1919

For the Installer

Adjust fresh air TURBO speed (or press % HUM key to keep it as is).

TURBO

Press on MODE key to raise

the value.

Press on TURBO key to lower

the value.

Ajust the airflow until the

reading on magnehelic gauge

reaches the stale airflow value.

MODE



TURBO



Install tubing on fresh

airflow pressure taps

and take the reading.

Check the magnehelic

gauge along with the unit

balancing chart until the

desired airflow is reached.

If you have selected the preset speed balancing at C, the balancing procedure is completed.

If you have selected the custom speed balancing, continue with the following:

Set CONT speed.

CONT

Press on MODE key to raise

the value.

Press on TURBO key to lower

the value.

Ajust the airflow until the

reading on magnehelic gauge

reaches the desired CFM value.

MODE



TURBO



Check the magnehelic

gauge along with the unit

balancing chart until the

desired airflow is reached.

Press % HUM key

to accept chosen

percentage.



% HUM

Write selected

airflow percentage

on label affixed on

the unit for future

reference.

Press % HUM key

to accept chosen

percentage.



% HUM

Write selected

airflow percentage

on label affixed on

the unit for future

reference.

2020

For the Installer

Press on MODE key to raise

the value.

Press on TURBO key to lower

the value.

Ajust the airflow until the

reading on magnehelic gauge

reaches the desired CFM value.

MODE



TURBO



Check the magnehelic

gauge along with the unit

balancing chart until the

desired airflow is reached.

Set RECIRC speed.

Press % HUM key to

accept chosen percentage

and exit the menu OR

wait 60 seconds.

Connect the

magnehelic gauge to

FRESH airflow taps.

Press on MODE key to raise

the value.

Press on TURBO key to lower

the value.

Ajust the airflow until the

reading on magnehelic gauge

reaches the desired CFM value.

MODE



TURBO



% HUM

Check the magnehelic

gauge along with the unit

balancing chart until the

desired airflow is reached.

NOTE: According to the installation, the magnehelic gauge tubing can be

connected to exhaust OR supply air flow. The arrow on screen will

shown which airflow will have to be set.

Set 20-minute push-button control speed.

Plug magnehelic gauge

tubing to STALE airflow.

Plug magnehelic gauge

tubing to FRESH airflow.

The balancing procedure is completed.

The adjusted airflow values are stored in the unit. If needed, any X-Touch main control can be used to adjust the unit speeds and

balance the unit again. If a power failure occurs, the unit will keep these setting values in memory. To change the setting values, go

to step G and follow the procedure, the new values will replace the previous ones.

Press % HUM key

to accept chosen

percentage.



% HUM

Write selected

airflow percentage

on label affixed on

the unit for future

reference.

Write selected

airflow percentage

on label affixed on

the unit for future

reference.

La page charge ...

NAPOLEON NERV2400T Manuel utilisateur

Marque: NAPOLEON

Modèle: NERV2400T

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: NAPOLEON NERV2400T User manual

Documents connexes

NAPOLEON NHRV75S Manuel utilisateur

NAPOLEON NERV2400T Manuel utilisateur

NAPOLEON NERV2400T Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents