Sharp LL-T1803-H Manuel utilisateur

LCD MONITOR

LCD FARBMONITOR

MONITEUR LCD

MONITOR LCD

LL-T1803-H

LL-T1803-B

OPERATION MANUAL

BEDIENUNGSANLEITUNG

MODE D’EMPLOI

MANUALE D’USO

MANUAL DE FUNCIONAMIENTO

Table of Contents / Inhaltsverzeichnis / Table des matières / Indice / Índice

English . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Deutsch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Français . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Italiano . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Español . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

2

3

English

Table of Contents

Notice for Users in the USA ............................................................................................................................ 4

TCO '95/ '99 ..................................................................................................................................................... 5

Notice for Users in Europe............................................................................................................................... 7

Notice for Users in the UK ............................................................................................................................... 8

Notice for Users in Australia ............................................................................................................................ 8

Tips and safety precautions ............................................................................................................................ 9

Product description .........................................................................................................................................10

Connecting the monitor and turning the monitor on and off ..............................................................................12

Connecting the monitor to a computer ........................................................................................................12

Connecting the monitor to a power source..................................................................................................12

Turning the power on ..................................................................................................................................13

Changing between input terminals ..............................................................................................................13

Turning the power off ..................................................................................................................................13

Adjusting the screen display ...........................................................................................................................14

Resetting all adjustment values .................................................................................................................14

Adjustment lock function............................................................................................................................14

Adjusting the backlight ...............................................................................................................................14

Adjusting the screen display (With analog connection) ...................................................................................15

Automatic screen adjustment.....................................................................................................................15

Manual screen adjustment .........................................................................................................................16

Adjusting the screen display (With digital connection) ....................................................................................19

Monitor care and repair ...................................................................................................................................21

Monitor care ...............................................................................................................................................21

Storage ......................................................................................................................................................21

Troubleshooting ..........................................................................................................................................21

Specifications .................................................................................................................................................22

Installing set-up information and the ICC profile (For Windows) ......................................................................25

Information about the ColorSync profile (For MacOS).....................................................................................28

Instructions for attaching a VESA compliant arm ...........................................................................................29

4

Notice for Users in the USA

FCC Statement

WARNING – FCC Regulations state that any unauthorized changes or modifications to this equipment

not expressly approved by the manufacturer could void the user's authority to operate this equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device

pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equip-

ment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the distance between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Use nothing but the included cables and AC cord to insure compliance with FCC regulation for Class B

computing equipment.

Declaration of Conformity

SHARP LCD Color Monitor LL-T1803-H/LL-T1803-B

This device complies with part 15 of the FCC rules. Operation is subject to the following conditions: (1)

this device may not cause harmful interference, and (2) this device must accept any interference re-

ceived, including interference that may cause undersized operation.

Responsible Party : SHARP ELECTRONICS CORPORATION

Sharp Plaza, Mahwah, New Jersey 07430

TEL :1-800-BE-SHARP

* As an ENERGY STAR Partner, SHARP has determined that this product meets the ENERGY STAR

guidelines for energy efficiency.

This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury. Disposal

of these materials may be regulated due to environmental considerations. For disposal or recycling

information, please contact your local authorities or the Electronics Industries Alliance:www.eiae.org

5

English

Congratulations!

You have just purchased a TCO’95 or TCO’99 approved and labelled product! Your choice has provided you

with a product developed for professional use. Your purchase has also contributed to reducing the burden on

the environment and also to the further development of environmentally adapted electronics products.

This product meets the requirements for the TCO’95 or TCO’99 scheme which provides for an international

environmental and quality labelling of personal computers. The labelling scheme was developed as a joint

effort by the TCO (The Swedish Confederation of Professional Employees), Svenska Naturskyddsforeningen

(The Swedish Society for Nature Conservation), Statens Energimyndighet (The Swedish National Energy

Administration) and SEMKO AB.

The requirements cover a wide range of issues: environment, ergonomics, usability, reduction of electric and

magnetic fields, energy consumption and electrical safety.

Why do we have environmentally labelled computers?

In many countries, environmental labelling has become an established method for encouraging the adaptation

of goods and services to the environment. The main problem, as far as computers and other electronics

equipment are concerned, is that environmentally harmful substances are used both in the products and during

their manufacture. Since it is not so far possible to satisfactorily recycle the majority of electronics equipment,

most of these potentially damaging substances sooner or later enter nature.

There are also other characteristics of a computer, such as energy consumption levels, that are important from

the viewpoints of both the work (internal) and natural (external) environments. Since all methods of electricity

generation have a negative effect on the environment (e.g. acidic and climate-influencing emissions, radioac-

tive waste), it is vital to save energy. Electronics equipment in offices is often left running continuously and

thereby consumes a lot of energy.

What does the environmenal labelling involve?

The environmental demands has been developed by Svenska Naturskyddsforeningen (The Swedish Society

for Nature Conservation). These demands impose restrictions on the presence and use of heavy metals,

brominated and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other things. The

product must be prepared for recycling and the manufacturer is obliged to have an environmental policy which

must be adhered to in each country where the company implements its operational policy.

The energy requirements include a demand that the computer and/or display, after a certain period of inactivity,

shall reduce its power consumption to a lower level in one or more stages. The length of time to reactivate the

computer shall be reasonable for the user.

Below you will find a brief summary of the environmental requirements met by this product. The complete

environmental criteria document may be ordered from:

TCO Development

SE-114 94 Stockholm, Sweden

Fax: +46 8 782 92 07

Email (Internet): development@tco.se

Current information regarding TCO’99 approved and labelled products may also be obtained via the Internet,

using the address: http://www.tco-info.com/

LL-T1803-B LL-T1803-H

6

Environmental requirements

Flame retardants

Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to

prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of

flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are

chemically related to another group of environmental toxins, PCBs. Both the flame retardants containing

bromine or chloride and the PCBs are suspected of giving rise to severe health effects, including reproductive

damage in fish-eating birds and mammals, due to the bio-accumulative * processes. Flame retardants have

been found in human blood and researchers fear that disturbances in foetus development may occur. The

relevant TCO´95 and TCO’99 demand require that plastic components weighing more than 25 grams must not

contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed

circuit boards since no substitutes are available.

Cadmium **

Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays.

Cadmium damages the nervous system and is toxic in high doses.

TCO’95 requirement states that batteries may not contain more than 25 ppm (parts per million) of cadmium.

The colour-generating layers of display screens must not contain any cadmium.

The relevant TCO’99 requirement states that batteries, the colour-generating layers of display screens

and the electrical or electronics components must not contain any cadmium.

Mercury **

Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is

toxic in high doses.

TCO’95 requirement states that batteries may not contain more than 25 ppm (parts per million) of mercury. The

relevant TCO’99 requirement states that batteries may not contain any mercury.

Both TCO´95 and TCO´99 also demand that mercury is not present in any of the electrical or electronics

components associated with the labelled unit. There is however one exception. Mercury is, for the time being,

permitted in the back light system of flat panel monitors as there today is no commercially available alterna-

tive. TCO aims on removing this exception when a mercury free alternative is available.

CFCs (freons)

The relevant TCO’95 and TCO’99 requirement state that neither CFCs nor HCFCs may be used during the

manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit

boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased

reception on earth of ultraviolet light with e.g. increased risks of skin cancer (malignant melanoma) as a

consequence.

Lead **

Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous

system and in higher doses, causes lead poisoning. The relevant TCO’95 and TCO´99 requirement permit the

inclusion of lead since no replacement has yet been developed.

* Bio-accumulative is defined as substances which accumulate within living organisms

** Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.

7

English

Notice for Users in Europe

This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by

93/68/EEC.

Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung

93/68/EWG.

Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par

la directive 93/68/CEE.

Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd door 93/68/

EEG.

Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr. 93/68/EEC.

Quest' apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/EEC, come emendata dalla

direttiva 93/68/EEC.

Η εγκατασταση ανταποκρινεται στιζ απαιτησειζ των οδηγιων τηζ Ευρωπαïκηζ Ενωσηζ 89/336/ΕΟΚ κατ 73/23/ΕΟΚ,

óπωζ οι κανονισµοι αυτοι συµπληρωθηκαν απó την οδηγια 93/68/ΕΟΚ.

Este equipamento obedece às exigências das directivas 89/336/CEE e 73/23/CEE, na sua versão

corrigida pela directiva 93/68/CEE.

Este aparato satisface las exigencias de las Directivas 89/336/CEE y 73/23/CEE, modificadas por medio

de la 93/68/CEE.

Denna utrustning uppfyller kraven enligt riktlinjerna 89/336/EEC och 73/23/EEC så som komplette ras av

93/68/EEC.

Dette produktet oppfyller betingelsene i direktivene 89/336/EEC og 73/23/EEC i endringen 93/68/EEC.

Tämä laite täyttää direktiivien 89/336/EEC ja 73/23/EEC vaatimukset, joita on muutettu direktiivillä 93/68/

EEC.

CAUTION :

TO PREVENT ELECTRICAL SHOCK, DISCONNECT THE AC CORD BEFORE SERVICING.

CAUTION :

FOR A COMPLETE ELECTRICAL DISCONNECTION, PULL OUT THE MAIN PLUG.

VORSICHT :

UM DIE STROMZUFUHR VOLLSTÄNDIG ZU UNTERBRECHEN, DEN NETZSTECKER HERAUSZIEHEN

ENTFERNEN.

ATTENTION :

POUR UN ARRET TOTAL DE L’APPAREIL, DEBRANCHEZ LA PRISE DU COURANT SECTEUR.

VARNING :

FÖR TOTAL ELEKTRISK URKOPPLING, KOPPLA UR KONTAKTEN OCH.

PRECAUCION :

PARA UNA COMPLETA DESCONEXION ELECTRICA DESENCHUFE LA CLAVIJA DE LA RED.

8

Notice for Users in the UK

FOR CUSTOMERS IN U.K.

IMPORTANT

The wires in this mains lead are coloured in accordance with the following code :

GREEN-AND-YELLOW : Earth

BLUE : Neutral

BROWN : Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured

markings identifying the terminals in your plug proceed as follows. The wire which is coloured GREEN-

AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the

safety earth or coloured green or green-and-yellow.

The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N

or coloured black.

The wire which is coloured BROWN must be connected to the terminal which is marked with the letter

L or coloured red.

Ensure that your equipment is connected correctly-if you are in any doubt consult a qualified

electrician.

"WARNING :THIS APPARATUS MUST BE EARTHED"

Notice for Users in Australia

Service Inquiries

Please contact your dealer for service if required or contact Sharp Corporation of Australia on

1 300 13 50 22 for referral to your nearest Sharp authorized Service Center.

9

English

- Under certain display conditions, minute specks

or spots may be noticeable. This is common for

liquid crystal monitors and is not a malfunction.

- The LCD panel has been manufactured using

highly elaborate technology. Properly working

pixels comprise 99.99% of total pixels. However,

please understand that 0.01% or less of pixels

may be missing or be brighter than usual.

- Do not leave the screen displaying idly for long

periods of time, as this could cause afterimage to

remain.

- If the brightness is adjusted to the minimum

setting it may be difficult to see the screen.

- The quality of the computer signal may influence

the quality of the display. We recommend using a

computer able to emit high quality video signals.

- Never rub or tap the monitor with hard objects.

- Please understand that Sharp Corporation bears

no responsibility for errors made during use by

the customer or a third party, nor for any other

malfunctions or damage to this product arising

during use, except where indemnity liability is

recognized under law.

- This monitor and its accessories may be

upgraded without advance notice.

Location

- Do not use the monitor where ventilation is poor,

where there is a lot of dust, where humidity is

high, or where the monitor may come into contact

with oil or steam, as this could lead to fire.

- Ensure that the monitor does not come into

contact with water or other fluids. Ensure that no

objects such as paper clips or pins enter the

monitor as this could lead to fire or electric

shock.

- Do not place the monitor on top of unstable

objects or in unsafe places. Do not allow the

monitor to come into contact with strong shocks

or vibrations. Causing the monitor to fall or topple

over may damage it.

- Do not use in places where the monitor will be

subject to direct sunlight, near heating equipment

or anywhere else where there is likelihood of high

temperature, as this may lead to generation of

excessive heat and outbreak of fire.

The Power Cord

- Do not damage the power cord nor place heavy

objects on it, stretch it or overly bend it. Also, do

not add extension cords. Damage to the cord may

result in fire or electric shock.

- Use only the AC adapter supplied with the

monitor. Using an AC adapter other than that

supplied may lead to fire.

- Insert the power plug directly into the AC outlet.

Adding an extension cord may lead to fire as a

result of overheating.

Monitor and accessory checklist

- Please check that the following items are

included in the package.

- LCD monitor (1)

- AC adapter (1)

(model name: NL-A61J)

- Analog signal cable (1)

(model name: 0LTGD15180001)

- Utility Disk (For Windows/Macintosh) (1)

- Operation manual (1)

Notes:

- The digital signal cable (DVI-D24 pin – DVI-D24

pin) is to be purchased separately. (model name:

NL-C01E)

- You are advised to retain the carton in case the

monitor needs to be transported.

- Sharp Corporation holds authorship rights to the

Utility Disk program. Do not reproduce it without

permission.

Use of AC adapter

- Do not use the AC adapter for other than the

specified equipment.

- Unplug the AC adapter if it is not used for long

time.

- Do not place any objects on the AC adapter.

- Do not use the AC adapter outdoors.

- Do not attempt to repair the AC adapter if it is

broken or malfunctioning. Refer the servicing to

the service representative.

- Do not try to open the AC adapter.

- Do not use water or wet cloth for cleaning the AC

adapter.

Manual Scope

- In this booklet, Microsoft Windows XP will be

referred to as [WindowsXP], Microsoft Windows

Millenium as [WindowsMe], Microsoft Windows

2000 as [Windows2000], Microsoft Windows 98

as [Windows98], Microsoft Windows 95 as

[Windows95], and Microsoft Windows Version 3.1

as [Windows3.1]. When there is no need to

distinguish between programs, the term

[Windows] will be used.

- Microsoft and Windows are registered

trademarks of Microsoft Corporation.

- Macintosh is a registered trademark of Apple

Computer, Inc.

Tips and safety precautions

10

Product description

654

32

1

78

11

10

9

1. INPUT button ............................ To switch between the signal’s input terminals. (Analog signal input

terminal

↔

DVI-D input terminal)

2. MENU button ............................ This button is used to pop-up, select and close the OSD (On Screen

Display) Menu.

3. SELECT button ........................ This button is used to select menu options when the OSD Menu is dis-

played.

4.

buttons .............................. When the OSD Menu is displayed:

These buttons are used to increase or decrease the value of a selected

option.

When the OSD Menu is not displayed:

These buttons are used to adjust backlight brightness .

5. Power LED ................................ This LED is lit green when in use and orange when in power-saving mode.

6. Power button

7. Power terminal

8. Analog signal input terminal ...... Use this when connecting to the computer’s analog RGB output terminal.

9. DVI-D input terminal .................. Use this when connecting to the computer’s digital RGB output terminal.

It can be connected to a computer with a DVI-compatible output terminal

(DVI-D24 pin or DVI-I29 pin) and which has SXGA output ability.

(Depending on the computer to be connected, correct display may or may

not be possible.)

In order to connect, it is necessary to purchase a Digital signal

cable.(Model name: NL-C01E)

10.Security lock anchor ................. By connecting a security lock (purchased separately) to the security lock

anchor, the monitor is fixed so that it cannot be transported.

The security slot works in conjunction with Kensington Micro Saver

Security Systems.

11.Ventilation openings .................. Note: Never block the ventilation openings as this may lead to overheat-

ing inside the monitor and result in malfunction.

11

English

Standing up and adjusting the monitor

CAUTION!

- Pressure from hands on the LCD panel could

cause damage.

- Be careful not to allow your fingers to be pinched.

Standing up the monitor

Press down on the stand and lift up the top section

of the monitor.

Folding up the monitor

1. Remove the AC adapter and the RGB signal

cable.

2. If carrying out adjustments to the monitor, place it

upright.

3. While pressing the rear lock disable button (1),

gently fold back the monitor (2).

(2)

(1)

Angle adjustment

Adjust to an easy to view angle.

45

15

Product description

12

CAUTION!

- When connecting, ensure that both the monitor

and computer are switched off.

- Be careful not to overly bend the cable or add

extension cords as this could lead to a

malfunction.

Connecting the monitor to a computer

Analog RGB connection

Connect this device’s analog signal cable to the

computer.

- Paying attention to connector direction, firmly

insert the signal cable to terminal, and then

tighten the screws at both sides.

If connecting to a D-sub 15 pin 2 row Apple Power

Macintosh, attach a Macintosh conversion adapter

(to be purchased separately) to the analog signal

cable.

Connecting the monitor and turning

the monitor on and off

Analog RGB terminal

(Mini D-Sub 15 pin, 3 row)

Analog signal cable

Macintosh conversion adapter

Digital RGB connection

Connecting the monitor to a computer via a Digital

signal cable. (to be purchased separately)

- For digital RGB connection, the monitor has an

input for connecting to a computer with a DVI-

compatible output connector (DVI-D 24 pin or DVI-

I 29 pin) and SXGA output capability. (Depending

on the type of computer to be connected, the

display may not work correctly.)

- Paying attention to connector direction, firmly

insert the signal cable to terminal, and then

tighten the screws at both sides.

Connecting the monitor to a power source

1. Connect the AC adapter to the monitor's power

terminal

2. Attach the power cord to the AC adapter and

place the power plug into the AC outlet.

Digital signal cable

Digital RGB output

terminal (DVI-D 24

pin or DVI-I 29 pin)

DVI-D input terminal

(DVI-D24 pin)

AC adapter

Power terminal

Power cord

AC outlet

13

English

Connecting the monitor and turning the monitor on and off

CAUTION!

- After unplugging the AC adaptor or power cord, be

sure to wait at least 10 seconds before plugging

in again. If you put the plug back in immediately

after unplugging, damage may be caused and the

screen malfunction or not display.

Turning the power on

1. Press the monitor's POWER button.

2. Turn on the computer.

The power LED will be lit green, and the screen

will display an image.

ON

Notes: (when using an analog signal)

- If using the monitor for the first time or after

having changed the system settings during use,

perform an automatic screen adjustment (p. 15).

- When connecting to a notebook, if the notebook

computer's screen is set so that it is displaying at

the same time, the MS-DOS screen may not be

able to display properly. In this case, change the

settings so that only the monitor is displaying.

Changing between input terminals

Use the INPUT button to switch between signal input

terminals.

Analog RGB signal Digital RGB signal

INPUT

INPUT-2(DIGITAL)

INPUT-1(ANALOG)

Turn on the

computer

Press power button

Turning the power off

1. Turn the computer off.

2. Press the monitor's POWER button.

The Power LED will disappear.

OFF

If the monitor is not going to be used for a long

period of time, be sure to unplug it from the AC

outlet.

Press power button

Turn the

computer off

14

Adjusting the screen display

For analog signal

1. First perform an automatic adjustment. (p. 15)

2. Perform manual adjustment where necessary.

(p. 16)

For digital signal

The monitor can generally be used without

adjustment. If necessary perform manual

adjustment. (p. 19)

Note:

- All adjustments will be saved even after turning

the power off.

Resetting all adjustment values

All adjustment values can be returned to their origi-

nal ex-factory values in one command.

1. Turn off the monitor power.

2. Press the MENU button and the SELECT button

simultaneously, and while doing this press the

power button (i.e. turn the power on). When [ALL

RESET] appears on the screen, the reset is

complete.

Note:

- While ALL RESET is displayed, the control

buttons are disabled.

- It is not possible to reset values when the

adjustment lock is in place. Remove the

adjustment lock before attempting to operate

control buttons.

Adjustment lock function

By disabling the control buttons (i.e. setting the lock)

any attempted changes to adjusted values will be

voided.

1. Turn off the monitor power.

2. While pressing the MENU button, press the

power button (i.e. turn the power on).

Continue to press the button until the message

appears on the screen.

When the menu is unlocked:

[ADJUSTMENT LOCKED] will appear on

the screen, and the lock will be set.

When the menu is locked:

[ADJUSTMENT UNLOCKED] will appear

on the screen, and the lock will be

removed.

Note:

- When the lock is in place, all buttons other than

the power button are disabled.

Adjusting the backlight

The backlight brightness can be adjusted.

Carry out the commands without the On Screen

Display (OSD) Menu displayed. If the OSD Menu is

displayed, press the MENU button (several times

may be required) and begin when the OSD Menu has

disappeared.

1. Without the OSD Menu being displayed, push the

or the button. At the bottom of the screen

the BRIGHT bar will appear.

2. Adjust by pressing the button (darker) or

button (lighter).

The BRIGHT bar automatically disappears several

seconds after the last command.

15

English

Adjusting the screen display (With analog connection)

Automatic screen adjustment

Options in the ADJUSTMENT Menu can be adjusted

automatically (CLOCK, PHASE, H-POS V-POS).

Note:

- When setting up this monitor for the first time or

after having changed an aspect of the current

system, perform an automatic screen adjustment

before use.

On Screen Display for the automatic

adjustment

First display an image that makes the entire screen

light.

If you are using Windows, you can use Adjustment

Pattern on the accompanying Utility Disk.

Opening the Adjustment Pattern (for Windows)

This explanation is for Windows 95/98/2000/Me/XP,

and assumes that the floppy disk drive is "A drive".

1. Place the Utility Disk (provided) into the

computer’s A drive.

2. Open [My Computer] and select [3 ½ Floppy

[A:]]. If using Windows 3.1, open [File Manager]

and choose A drive.

3. Double click on [Adj_uty.exe] to run the

Adjustment Program. The Adjustment Pattern will

appear.

Adjustment pattern

Notes:

- After completing the adjustments, press the

computer’s [Esc] key to exit the Adjustment

Program.

- If your computer’s display mode is set to 65K

colors, you may see the different color levels in

each color pattern or the gray scale may look

colored. (This is due to the specification of the

input signal and is not a malfunction.)

How to Adjust

1. Press the MENU button.

The ADJUSTMENT Menu will be displayed.

2. Press the button.

The screen will become dark and [ADJUSTING]

will be displayed. After a few seconds the

ADJUSTMENT Menu will return. (The automatic

adjustment is now complete.)

3. Press the MENU button 4 times to make the

OSD Menu disappear.

Notes:

- In most cases automatic adjustment is sufficient.

- If necessary due to any of the following, manual

adjustments (p. 16) can be performed after the

automatic adjustment.

- When further fine adjustment is needed.

- When the computer’s video input signals are

Composite Sync or Sync On Green.

(Automatic adjustments may not be possible.)

- When [OUT OF ADJUST] is displayed.

(When the screen displays an entirely dark

image, the automatic screen adjustment may

be disabled. When making an automatic

adjustment, be sure to either use the

Adjustment Pattern or try displaying an image

that makes the entire screen very bright.)

16

Manual screen adjustment

Adjustments can be made using On Screen Display

(OSD) Menu provided.

On Screen Display for adjustment

If you are using Windows, open the Adjustment

Pattern on the accompanying Utility Disk. (p. 15).

If your system is not Windows, you can not use the

Adjustment Pattern. Therefore display an image that

makes the entire screen light and adjust it through

checking visually its actual tone.

This chapter provides the procedure how to adjust

the screen by using Adjustment Pattern (for Win-

dows)

How to adjust

1. Press the MENU button.

The ADJUSTMENT Menu will be displayed.

At this point relevant menu options can be

adjusted.

Each time the MENU button is pressed the next

menu is selected. (ADJUSTMENT → GAIN

CONTROL → WHITE BALANCE → MODE

SELECT → OSD Menu disappears)

Notes:

- The OSD Menu automatically disappears several

seconds after the last command.

ADJUSTMENT Menu

MANUAL: Individual menu options are manually

adjusted.

AUTO: Every menu option is automatically

adjusted.

Notes:

- Press the

button to select [AUTO].

- To choose a menu option:SELECT button

- To go to the next menu: MENU button

CLOCK

The figure below demonstrates how to adjust so that

vertical flicker noise is not emitted. (

buttons)

PHASE

The figure below demonstrates how to adjust so that

horizontal flicker noise is not emitted. (

buttons)

Note:

- Adjustments to PHASE should be made only

after CLOCK has been correctly set.

H-POS (horizontal positioning) and V-POS

(vertical positioning)

To center the screen image within the boundaries of

the screen, adjust the left-right (H-POS) values and

the up-down (V-POS) values. (

buttons)

Adjusting the screen display (With analog connection)

Vertical flicker noise

Horizontal flicker noise

Screen frame

17

English

WHITE BALANCE Menu

Notes:

- On settings other than [STD] not all graduations

can be displayed. To display all graduations, set

to [STD].

- Use the

buttons to select [COOL], [·], [STD],

[·], [WARM] or [USER].

- Selecting USER will display the setting values for

[R-CONTRAST], [G-CONTRAST] and

[B-CONTRAST], in order to make fine

adjustments.

- Use the SELECT button to select

[R-CONTRAST], [G-CONTRAST] and

[B-CONTRAST].

- To go to the next menu: MENU button

COOL ... Color tone bluer than standard

•......... Color tone slightly bluer than standard

STD ...... Color tone standard setting

•......... Color tone slightly redder than standard

WARM .. Color tone redder than standard

USER

R-CONTRAST ....

button for blue-green

button for red

G-CONTRAST ....

button for purple

button for green

B-CONTRAST ....

button for yellow

button for blue

GAIN CONTROL Menu

MANUAL: Individual menu options are manually

adjusted.

AUTO: Every menu option is automatically

adjusted using the Auto Gain Control*

function.

Notes:

- Press the

button to select [AUTO].

- To choose a menu option:SELECT button

- To go to the next menu: MENU button

* Auto Gain Control function

- The Auto Gain Control adjusts contrast and black

level based on the brightest color of the image

displayed. If you are not using the Adjustment

Pattern it is necessary to have an area of 5 mm x

5 mm of white displayed, and if not adjustments

may not be possible. (In such case, [OUT OF

ADJUST] will appear and setting values remain

unchanged.)

- If the signal coming from the computer is

composite sync or sync on green, automatic

adjustment cannot be performed. Please perform

manual adjustment instead.

BLACK LEVEL

Total screen brightness can be adjusted while

watching the color pattern. (

buttons)

CONTRAST

While watching the color pattern, adjustments can be

made so that all graduations appear. (

buttons)

Adjusting the screen display (With analog connection)

Color pattern

18

MODE SELECT Menu

Notes:

- Depending on the resolution of the input signal,

even if menu options can be selected, the display

may not change.

- To choose a menu option: SELECT button

- When adjustment complete: MENU button

OSD H-POSITION (OSD horizontal position)

The position of the OSD display can be moved to the

left and right. (

buttons)

OSD V-POSITION (OSD vertical position)

The position of the OSD display can be moved up

and down. (

buttons)

INPUT (Input mode)

The input mode can be set. (

buttons)

VESA: VESA mode

MAC: Power Macintosh mode

400 LINES (degree of resolution)

You can specify the horizontal resolution of a 400-

line screen when using US text, etc. (

buttons)

640: 640 X 400 dot mode

720: 720 X 400 dot mode (US text etc.)

Note:

- As the resolution input for other than 400 lines is

done automatically, there is no need to set it.

SCALING (Level of scaling)

Adjusts the image to optimum sharpness when

Screen expansion is taken. (

buttons)

LANGUAGE

You can chose the language used in OSD Menu.

1. Press the

button.

Language Selection Menu (LANGUAGE) will

appear.

2. Chose the desired language by SELECT button.

3. Press MENU button or the

button, and

Language Selection Menu will disappear.

Adjusting the screen display (With analog connection)

19

English

Adjusting the screen display (With digital connection)

Adjustments can be made using On Screen Display

(OSD) Menu provided.

On Screen Display for adjustment

If you are using Windows, open the Test Pattern on

the accompanying Utility Disk. (p. 15)

If your system is not Windows, you can not use the

Adjustment Pattern. Therefore display an image that

makes the entire screen light and adjust it through

checking visually its actual tone.

How to adjust

1. Press the MENU button.

The WHITE BALANCE Menu will be displayed.

At this point relevant menu options can be

adjusted.

Each time the MENU button is pressed the next

menu is selected. (WHITE BALANCE → MODE

SELECT → OSD Menu disappears)

Notes:

- The OSD Menu automatically disappears several

seconds after the last command.

WHITE BALANCE Menu

Notes:

- On settings other than [STD] not all graduations

can be displayed. To display all graduations, set

to [STD].

- Use the

buttons to select [COOL], [·], [STD],

[·], [WARM] or [USER].

- Selecting USER will display the setting values for

[R-CONTRAST], [G-CONTRAST] and

[B-CONTRAST], in order to make fine

adjustments.

- Use the SELECT button to select

[R-CONTRAST], [G-CONTRAST] and

[B-CONTRAST].

- To go to the next menu: MENU button

COOL ... Color tone bluer than standard

•......... Color tone slightly bluer than standard

STD ...... Color tone standard setting

•......... Color tone slightly redder than standard

WARM .. Color tone redder than standard

USER

R-CONTRAST ....

button for blue-green

button for red

G-CONTRAST ....

button for purple

button for green

B-CONTRAST ....

button for yellow

button for blue

20

Adjusting the screen display (With digital connection)

MODE SELECT Menu

Notes:

- Depending on the resolution of the input signal,

even if menu options can be selected, the display

may not change.

- To choose a menu option: SELECT button

- When adjustment complete: MENU button

OSD H-POSITION (OSD horizontal position)

The position of the OSD display can be moved to the

left and right. (

buttons)

OSD V-POSITION (OSD vertical position)

The position of the OSD display can be moved up

and down. (

buttons)

SCALING (Level of scaling)

Adjusts the image to optimum sharpness when

Screen expansion is taken. (

buttons)

LANGUAGE

You can chose the language used in OSD Menu.

1. Press the

button.

Language Selection Menu (LANGUAGE) will

appear.

2. Chose the desired language by SELECT button.

3. Press MENU button or the

button, and

Language Selection Menu will disappear.

La page charge ...

Sharp LL-T1803-H Manuel utilisateur

Ce manuel convient également à

Sharp LL-T1803-H Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents