Sony DR-BT21G Mode d'emploi

Wireless Stereo

Headset

3-095-524-61(1)

DR-BT21G

Operating Instructions

Mode d’emploi

US

FR

2

US

WARNING

To reduce the risk of fire or electric

shock, do not expose this

apparatus to rain or moisture.

To reduce the risk of electrical

shock, do not open the cabinet.

Refer servicing to qualified

personnel only.

Do not install the appliance in a confined

space, such as a bookcase or built-in

cabinet.

To reduce the risk of fire, do not cover the

ventilation of the apparatus with

newspapers, tablecloths, curtains, etc.

And do not place lighted candles on the

apparatus.

To reduce the risk of fire or electric

shock, do not place objects filled with

liquids, such as vases, on the apparatus.

Connect the AC power adaptor to an

easily accessible AC outlet. Should you

notice an abnormality in the AC power

adaptor, disconnect it from the AC outlet

immediately.

Do not expose the battery to excessive

heat such as direct sunlight, fire or the

like.

For the customers in the USA

Owner’s Record

The model number is located at the front

of both housing. You can check the serial

number at the left by detaching the ear

pad.

Record these numbers in the spaces

provided below. Refer to them whenever

you call upon your Sony dealer regarding

this product.

Model No. DR-BT21G

Serial No.

Information

This device complies with Part 15 of FCC

Rules and RSS-Gen of IC Rules.

Operation is subject to the following two

conditions: (1) this device may not cause

interference, and (2) this device must

accept any interference, including

interference that may cause undesired

operation of this device.

You are cautioned that any changes or

modifications not expressly approved in

this manual could void your authority to

operate this equipment.

This equipment must not be co-located or

operated in conjunction with any other

antenna or transmitter.

This equipment complies with FCC/IC

radiation exposure limits set forth for

uncontrolled equipment and meets the

FCC radio frequency (RF) Exposure

Guidelines in Supplement C to OET65

and RSS-102 of the IC radio frequency

(RF) Exposure rules. This equipment has

very low levels of RF energy that it is

deemed to comply without testing of

specific absorption ratio (SAR).

The Bluetooth word mark and logos are

owned by the Bluetooth SIG, Inc. and any

use of such marks by Sony Corporation is

under license.

Other trademarks and trade names are

those of their respective owners.

MPEG Layer-3 audio coding technology

and patents licensed from Fraunhofer IIS

and Thomson.

3

US

For the customers in the Canada

RECYCLING LITHIUM-ION

BATTERIES

Lithium-Ion batteries

are recyclable.

You can help preserve

our environment by

returning your used

rechargeable batteries

to the collection and recycling location

nearest you.

For more information regarding

recycling of rechargeable batteries, call

toll free 1-800-822-8837, or visit

http://www.rbrc.org/

Caution: Do not handle damaged or

leaking Lithium-Ion batteries.

Table Of Contents

Welcome! .......................... 4

3 steps to Bluetooth

function ................................. 5

Location and Function of

Parts ............................... 6

Folding and unfolding the

headset ................................. 7

Charging the unit ............. 8

Pairing ............................. 10

What is pairing? ...................... 10

Procedures of pairing .............. 10

Wearing the headset ...... 12

Indications of

Bluetooth function...... 13

Listening to music ......... 14

Controlling the audio

device – AVRCP ................. 15

Calling ............................. 16

Controlling the Bluetooth

mobile phone – HFP, HSP .. 18

Calling while playing

back music .................. 19

Disposing of the unit ..... 20

Precautions .................... 21

What is Bluetooth wireless

technology? ................ 23

Troubleshooting ............. 24

Initializing the unit ......... 26

Specifications ................. 27

4

US

Welcome!

Thank you for purchasing this Sony Wireless Stereo Headset. This unit uses

Bluetooth

™

wireless technology.

• Enjoy music wirelessly with a Bluetooth music player.*

1

• Hands-free conversation can be enjoyed on your Bluetooth mobile phone

without taking it out of your bag.*

2

• For convenience, you can remotely operate the basic functions of a

Bluetooth music player (Play, Stop, etc.).*

3

• Useful rechargeable function.

• Convenient foldable type for easy carrying.

For details on Bluetooth wireless technology, see page 23.

Listening to music

Talking on the phone

*1

The connected Bluetooth device is required to support A2DP (Advanced Audio

Distribution Profile).

*2

The connected Bluetooth device is required to support HSP (Headset Profile) or HFP

(Hands-free Profile).

*3

The connected Bluetooth device is required to support AVRCP (Audio Video Remote

Control Profile).

5

US

V

Calling

V

Listening to music

V

3 steps to Bluetooth function

Bluetooth connection

Operate the Bluetooth device to

make the Bluetooth connection.

Connection

Listening to music

You can listen to music played on

the Bluetooth device.

Playback, stop, or pause is

possible from this unit.

Music

Bluetooth connection

When the unit is turned on, the

unit starts making the Bluetooth

connection to the recognized

mobile phone automatically.

Talking on the phone

You can make and receive a call

by operating this unit.

Pairing

First, register (“pair”) a Bluetooth device (mobile phone, etc.) and this

unit with each other. Once pairing is established, there is no need for

pairing again.

Voice

Connection

A2DP

AVRCP

HFP HSP

c Page 10

c Page 14

c Page 16

c Page 17 - 19c Page 14 - 15

Bluetooth

mobile phone,

etc.

Pairing

Wireless Stereo

Headset

6

US

Location and Function of Parts

1 Indicator (blue)

Indicates the communication

status of the unit.

2 Indicator (red)

Indicates the power status of

the unit.

3 Multi function button

Controls various call functions.

Press the button on the tactile

dots.

4 Jog switch

Controls various functions

when listening to music.

5 RESET button

Push this button when this unit

does not operate properly.

Pairing information is not

deleted by this operation.

6 VOL (volume) +*⁄–

buttons

7 Neckband

8 R (right) indication

9 Left unit L

0 L (left) indication

qa Ear pad

qs Right unit R

qd POWER button

qf Microphone

qg DC IN 3 V jack

GETTING STARTED

* This button has a tactile dot.

7

US

Folding and unfolding the headset

Unfolding

1 Unfold the left and right

neckband as illustrated.

2 Lift up and open up the

remaining half of the

neckband.

Notes

• Do not pull open this way.

• Be careful not to hit your face or eyes

with the top of the neckband.

Folding

1 Hold near the foldable

part with both hands

and lift up the left unit to

fold it as illustrated.

Fold the right unit in the same

manner.

2 Close the folded left and

right neckband.

8

US

1 Connect the supplied

AC power adaptor to the

DC IN 3 V jack on the

unit.

When the AC power adaptor is

connected to an AC outlet,

charging starts.

Tip

If the AC power adaptor is connected

to an AC outlet while the unit is

turned on, the unit will be turned off

automatically.

Charging the unit

The unit contains a rechargeable Lithium-Ion battery, which should be

charged before using for the first time.

Wireless Stereo

Headset

To DC IN

3 V jack

To an

AC outlet

AC power

adaptor

(supplied)

2 Make sure that indicator

(red) lights up while

charging.

Charging is completed in about

3 hours* and the indicator (red)

goes off automatically.

* Time required for empty battery to

recharge.

Caution

If this unit detects a problem while

charging, the indicator (red) may

turn off, although charging is not

complete.

Check for the following causes:

– Ambient temperature exceeds the

range of 0 °C – 40 °C (32 °F –

104 °F).

– There is a problem with the

battery.

In this case, charge again within the

above-mentioned temperature range.

If the problem persists, consult your

nearest Sony dealer.

9

US

Approx.

usage hours

11 hours

100 hours

Status

Full

Mid

Low (needs to

charge)

Checking the remaining

battery

When pressing the POWER button

while the unit is turned on, the

indicator (red) flashes. You can

check the remaining battery by the

number of times the indicator (red)

flashes.

Indicator (red)

3 times

2 times

1 time

Note

You cannot check the remaining battery

immediately after the unit is turned on, or

while pairing.

When the battery is almost empty

The indicator (red) flashes slowly

automatically.

When the battery becomes empty, a

beep sounds and the unit will turn

off automatically.

Notes

• If the battery is not used for a long time,

battery may be quickly depleted,

however, after a few recharges, battery

life will improve.

• If the life of the built-in rechargeable

battery drops to half the normal length,

the battery should be replaced. Consult

your nearest Sony dealer for

replacement of the rechargeable battery.

• Avoid exposure to temperature

extremes, direct sunlight, moisture,

sand, dust or mechanical shock. Never

leave in a car parked in the sun.

• Use only the supplied AC power

adaptor. Do not use any other AC

power adaptor.

Usage hours

*

Status

Communication

time (including

music playback

time) (up to)

Standby time

(up to)

* Time stated above may vary, depending

on ambient temperature or conditions of

use.

10

US

Pairing

What is pairing?

Bluetooth devices need to be

“paired” with each other

beforehand.

Once Bluetooth devices are paired,

there is no need for pairing again,

except in the following cases:

• Pairing information is deleted

after repair, etc.

• This unit is paired with 9 or more

devices.

This unit can be paired with up to

8 devices; if a new device is

paired after 8 devices have been

paired, the device whose latest

connection time is the oldest

among the 8 paired devices is

replaced by the new one.

• When recognition of the unit by

the device to be connected is

deleted.

• This unit is initialized.

All pairing information is deleted.

Procedures of pairing

1 Place the Bluetooth

device within 1 m (3 ft)

of this unit.

2 Press and hold the

POWER button for

7 seconds or more to

standby for pairing

while the unit is turned

off.

Notes

• After about 3 seconds, power is

turned on and the indicator (blue)

and indicator (red) flash together

twice. Keep the button pressed

without releasing until both

indicators start flashing together,

then release the button. This unit

enters into pairing mode.

• If pairing is not established within

about 5 minutes, pairing mode will

be cancelled and this unit will turn

off. In this case, start over from

step 1.

11

US

3 Perform pairing

procedure on the

Bluetooth device to

detect this unit.

The list of detected devices

appears on the display of the

Bluetooth device. This unit is

displayed as “DR-BT21G.”

If “DR-BT21G” is not

displayed, repeat from step 1.

4 Select “DR-BT21G” on

the display of the

Bluetooth device.

5 If Passcode* input is

required on the display

of a Bluetooth device,

input “0000.”

Pairing is complete when the

indicator (blue) flashes slowly.

The message standing for

“Pairing complete” appears on

the display of some Bluetooth

devices.

* Passcode may be called “Passkey,”

“PIN code,” “PIN number,” or

“Password.”

6 Start the Bluetooth

connection from the

Bluetooth device.

This unit memorizes the device

as the last connected device.

Some Bluetooth devices may

connect with the unit

automatically when pairing is

complete.

When pairing with a

Bluetooth device that

cannot display a list of

detected devices or that

has no display

You may pair the device by setting

both this unit and the Bluetooth

device to pairing mode. For details,

refer to the operating instructions

supplied with the Bluetooth device.

Tips

• To pair with other Bluetooth devices,

repeat steps 1 to 5 for each device.

• To delete all pairing information, see

“Initializing the unit” (page 26).

12

US

1 Place the neckband on

the neck.

The unit with the POWER

button is the right unit (for right

ear).

2 Lift up the headset

slightly above the ear

level, put down the

neckband so that it

hooks on your ears and

put the ear pads on your

ears.

Wearing the headset

Neckband

Left ear

Ear pad

3 Adjust the angle and

position of the

neckband so that the

heaset is fitted

comfortably on your

ears.

13

US

Pairing

Connecting

Connected

Phone

Music

Indications of Bluetooth function

B : Indicator (blue)

R : Indicator (red)

Status Flashing patterns

Searching

B

– – – – – – – –

...

R

– – – – – – – –

...

Connectable

B

– – – – – – – – – –

...

R

–

Connecting

B

– – – – – – – – – –

...

R

– – – – – – – – – –

...

HFP/HSP or A2DP

B

– – – – – – – – – – – – – –

...

(standby for receiving audio signal)

R

–

HFP/HSP and A2DP

B

– – – – – – – – – – – –

...

(standby for receiving audio signal)

R

–

Listening

B

– – – – – – – – – – – –

...

R

–

Listening during standby

B

– – – – – – – – – –

...

for telephone call

R

–

Incoming call

B

...

R

–

Talking

B

– – – – – – – – – – – –

...

R

–

Calling while

B

– – – – – – – – – –

...

playing back music

R

–

14

US

VOL – button

FF

REW

Check the following before

operating the unit.

– The Bluetooth device is turned

on.

– Pairing of this unit and the

Bluetooth device is complete.

– The Bluetooth device supports the

transmitting music function

(profile: A2DP*).

1 Press and hold the

POWER button for

about 3 seconds while

the unit is turned off.

The indicator (blue) and

indicator (red) flash together

twice and the unit is turned on.

Notes

• Do not press and hold the POWER

button for more than 7 seconds,

otherwise pairing mode is entered.

• After the unit is turned on, the unit

attempts to connect to the last

connected Bluetooth device

automatically with HFP or HSP. To

make or receive a call while

listening to music, make ready the

last connected Bluetooth device for

HFP or HSP connection before

turning on the headset.

Listening to music

2 Make the Bluetooth

connection (A2DP) from

a Bluetooth device to

this unit.

Refer to the operating

instructions supplied with the

Bluetooth device on how to

operate it.

3 Start playback on the

Bluetooth device.

Tip

Bluetooth connection of A2DP

(Advanced Audio Distribution Profile)

can also be operated with the jog switch

from this unit to the Bluetooth device

except when making a call on this unit.

Note

When you play music by connecting the

unit to a Bluetooth device using HSP

(Headset Profile), sound quality will not

be high. For better sound, change the

Bluetooth connection to A2DP by

operating the Bluetooth device.

* For detail on profiles, see page 24.

OPERATING THE UNIT

VOL + button

POWER button

15

US

To adjust the volume

Press the VOL + or – button while

listening to the music.

Tips

• Depending on the connected device, it

may be necessary to adjust the volume

on the connected device as well.

• Volume level for calling and listening

to music can be set independently.

To stop use

1 Terminate the Bluetooth

connection by operating

the Bluetooth device.

2 Press and hold the

POWER button for

about 3 seconds.

The indicator (blue) and

indicator (red) light up together,

and the unit turns off.

Tip

When you finish playing music, the

Bluetooth connection may terminate

automatically, depending on the

Bluetooth device.

Controlling the audio

device – AVRCP

If the Bluetooth audio device

connected with this unit supports

AVRCP (Audio Video Remote

Control Profile), you can control by

using the unit buttons.

Refer to the operating instructions

supplied with the Bluetooth device

on how to operate it.

Note

Operation of the Bluetooth connecting

device by this unit will vary depending on

its specification.

Status: In stop or pause mode

1 Starts playback*

1

2 Stop

3 Skip to next/previous

4 Fast-forward/Fast-rewind*

2

Status: In play mode

5 Pause*

1

6 Stop

7 Skip to next/previous

8 Fast-forward/Fast-rewind*

2

*

1

You may need to press the button

twice depending on the Bluetooth

device.

*

2

Some

Bluetooth

devices may not

operate.

Note

You cannot adjust the volume of the

Bluetooth device by the unit volume

buttons.

Short Press Long Press

Nx

FF / REW

Short Press Long Press

Nx

FF / REW

5

7

6

8

1

3

2

4

16

US

When this unit does not

connect to a Bluetooth

mobile phone automatically

You can make a connection by

operating Bluetooth mobile phone

or by operating this unit to connect

the last connected Bluetooth device.

A To make a connection

by operating Bluetooth

mobile phone

1 Make the Bluetooth

connection (HFP or

HSP*) from the

Bluetooth mobile phone

to this unit.

Refer to the manual supplied

with your Bluetooth mobile

phone for operation details.

The list of recognized devices

appears on the display of the

Bluetooth mobile phone. This

unit is displayed as

“DR-BT21G.”

When you use the Bluetooth

mobile phone features both HFP

(Hands-free Profile) and HSP

(Headset Profile), set to HFP.

Note

When connecting to a Bluetooth

mobile phone which is different from

the last connected one, make the

connection following the above

procedure.

* For details on profiles, see

page 23.

Check the following before

operating the unit.

– The Bluetooth function is active

on the mobile phone.

– Pairing of this unit and the

Bluetooth mobile phone is

complete.

1 Press and hold the

POWER button for

about 3 seconds while

the unit is turned off.

The indicator (blue) and

indicator (red) flash together

twice, the unit turns on and then

this unit tries to connect to the

last Bluetooth mobile phone that

was used.

Note

Do not press and hold the POWER

button for more than 7 seconds,

otherwise pairing mode is entered.

Tip

This unit will stop trying to connect

to the Bluetooth mobile phone after 1

minute. In such a case, press the multi

function button to try to connect

again.

Calling

VOL – button

POWER button

VOL + button

Multi function

button

17

US

– ring tone set on the unit

– ring tone set on the mobile

phone

– ring tone set on the mobile

phone only for Bluetooth

connection

Note

If you received a call by pressing the

button on the Bluetooth mobile phone,

some Bluetooth mobile phones may have

handset use priority. In this case, set to

talk with the unit by pressing and holding

the multi function button for about 2

seconds, or by operating the Bluetooth

mobile phone. For details, refer to the

manual supplied with your Bluetooth

mobile phone.

To adjust the volume

Press the VOL + or – button.

Tips

• You cannot adjust the volume when not

communicating.

• Volume level for calling and listening

to music can be set independently.

To terminate a call

You can end a call by pressing the

multi function button on the unit.

To stop use

1 Terminate Bluetooth

connection by the

Bluetooth mobile

phone.

2 Press and hold the

POWER button for

about 3 seconds to turn

off the power.

The indicator (blue) and

indicator (red) light up together,

and the unit turns off.

B To make a connection

with the last connected

Bluetooth device by

operating this unit

1 Press the multi function

button.

The indicator (blue) and

indicator (red) start flashing at

the same time, and the unit

performs the connection

operation for about 5 seconds.

Note

When listening to music with this unit, a

Bluetooth connection cannot be made

with the multi function button.

To call

1 Use the buttons on your

mobile phone when

making a call.

If no dial tone is heard on this

unit, press and hold the multi

function button for about 2

seconds.

Tip

You can call in the following way,

depending on the Bluetooth mobile

phone. Refer to the manual supplied with

your mobile phone on operating details.

– When not communicating, you can call

using the voice-dial function by

pressing the multi function button.

– You can call the last dialed number by

pressing the multi function button for

about 2 seconds.

To receive a call

When an incoming call arrives, a

ring tone will be heard from the

unit.

1 Press the multi function

button on the unit.

The ring tone differs in the

following ways, depending on

your mobile phone.

Continued

18

US

Controlling the

Bluetooth mobile

phone – HFP, HSP

The operation of the buttons on this

unit varies depending on your

mobile phone.

HFP (Hands-free Profile) or HSP

(Headset Profile) is used for

Bluetooth mobile phone. Refer to

the operating instructions supplied

with your Bluetooth mobile phone

on supported Bluetooth profiles or

how to operate.

HFP (Hands-free Profile)

HSP (Headset Profile)

*

1

Some functions may not be supported

depending on the Bluetooth mobile

phone.

*

2

This may vary, depending on the

Bluetooth mobile phone.

*

3

Some functions may not be supported

when calling using the Bluetooth

mobile phone.

Status Multi function button

Standby

Voice Dial

active

Outgoing call

Incoming call

During call

Short Press

Start Voice

Dial

Cancel Voice

Dial

End outgoing

call

Answer

End call

Long Press

Last number

redial

–

Reject

Change active

device

Status Multi function button

Standby

Outgoing call

Incoming call

During call

Short Press

–

End outgoing

call

*

1

Answer

End call

*

3

Long Press

Dial

*

1

End outgoing

call or change

active device to

headset*

2

–

Change active

device to

headset

19

US

Calling while playing back music

The Bluetooth connection using HFP or HSP as well as A2DP is necessary

to make a call while playing back music.

For example, to make a call using a Bluetooth mobile phone while listening

to music on a Bluetooth compatible music player, this unit needs to be

connected to the mobile phone using HFP or HSP.

Make a Bluetooth connection between this unit and the

device in use following the procedures outlined below.

1 Make a Bluetooth connection between this unit and

the mobile phone in use with HFP or HSP following

the procedures outlined in “Calling” (see page 16).

2 Operate the Bluetooth device (music player or mobile

phone) used for playing the music to make a

Bluetooth connection to this unit using A2DP.

To receive a call while

playing back music

When an incoming call arrives, the

music pauses and the ring tone is

heard from this unit.

1 Press the multi function

button and talk.

After finishing the call, press the

multi function button. This unit

is switched back to music

playback.

When no ring tone is heard

even if an incoming call

arrives

1 Stop music playback.

2 When ringing, press the

multi function button

and talk.

To make a call while

playing back music

1 Press the multi function

button while playing

back music (page 18), or

operate your Bluetooth

mobile phone to make a

telephone call.

If no dial tone is heard on this

unit, press and hold the multi

function button for about 2

seconds.

20

US

Disposing of the unit

This unit has a Lithium-lon rechargeable battery built in the left unit.

For environmental conservation, be sure to remove the built-in rechargeable

batteries from the unit before disposing, and dispose of the batteries

appropriately.

ADDITIONAL INFORMATION

1 Remove the ear pad on

the left unit, and then

detach the left unit.

The unit is fixed with claws (3

places). As illustrated, insert an

object such as flathead

screwdriver into the gap and lift

up the unit to detach it.

2 Remove the screw

which fixes the external

cover.

3 Open the external cover

and remove the inside

circuit board.

1 The external cover is fixed

with claws (3 places). Insert

an object such as flathead

screwdriver into the gap and

detach the cover.

2 The circuit board is fixed

with a claw. As illustrated,

insert an object such as

flathead screwdriver into the

gap at the connector to lift

up the circuit board to

remove it.

1

2

4 Pull out the connector

and remove the

rechargeable battery.

The rechargeable battery is fixed

with adhesive tape. Insert an

object such as flathead

screwdriver and lift up the

battery to remove it.

Rechargeable

battery

Left

housing

Claws

Fixed screw

1

2

La page charge ...

Sony DR-BT21G Mode d'emploi

Ce manuel convient également à

Sony DR-BT21G Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents