Wacker Neuson PS31500 Manuel utilisateur

Operator’s Manual

Notice d'emploi

Pump

Pompe

PS3 1500

PS3 2200

Type PS3 1500, PS3 2200

Document 5000187845

Date 1115

Version 03

Language EN-FR

5000187845

Copyright notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the

machine. Any other type of reproduction is prohibited without express

written permission from Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker

Neuson Production Americas LLC represents an infringement of valid

copyrights. Violators will be prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their

respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original instructions

This Operator’s Manual presents the original instructions. The original

language of this Operator’s Manual is American English.

PS3 1500 / PS3 2200 Foreword

wc_tx002040gb.fm 3

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

Machines discussed in this manual:

Machine

documentation

 From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 Refer to the separate Repair Manual for detailed instructions on servicing and

repairing the machine.

 If you are missing any of these documents, please contact Wacker Neuson to

order a replacement or visit www.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and observe all instructions

described in this manual.

 Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change

any portion of this information without notice.

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and

modifications. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

 Approved modifications are those performed by an authorized Wacker

Neuson service center according to written instructions published by Wacker

Neuson.

 Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following

consequences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Part No. PS3 1500

0009117, 0009118

PS3 2200

0009119

Foreword PS3 1500 / PS3 2200

4 wc_tx002040gb.fm

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

wc_bo5000187821_03TOC.fm 5

Table of ContentsPS3 1500 / PS3 2200

Foreword 3

1 Safety Information 7

1.1 Signal Words Used in this Manual ....................................................... 7

1.2 Machine Description and Intended Use ............................................... 8

1.3 Operating and Electrical Safety ............................................................ 9

1.4 Service Safety .................................................................................... 10

1.5 Labels ................................................................................................. 11

2 Lifting and Transporting 12

3 Installation 13

3.1 Components ....................................................................................... 13

3.2 Preparing the Machine for First Use ................................................... 14

3.3 Application Area ................................................................................. 14

3.4 Maximum Allowable Water Pressure ................................................. 15

3.5 Preparing for installation ..................................................................... 15

3.6 Checks to Make Before Installation .................................................... 17

3.7 Changing the Operating Voltage ........................................................ 18

3.8 Precautions in Installation .................................................................. 20

3.9 Electrical Wiring .................................................................................. 21

3.10 Connecting the power supply ............................................................. 21

3.11 Cable Assembly ................................................................................. 22

4 Operation 23

4.1 Before Starting ................................................................................... 23

4.2 Operating Water Level ..................................................................... 25

4.3 Motor Protection System .................................................................... 25

4.4 Emergency Shutdown Procedure ....................................................... 26

5 Maintenance 27

5.1 Periodic Maintenance Schedule ......................................................... 27

5.2 Maintenance and Inspection .............................................................. 28

5.3 Storage ............................................................................................... 28

5.4 Disassembly and Reassembly ........................................................... 30

5.5 Disassembly ....................................................................................... 31

5.6 Reassembly ........................................................................................ 32

5.7 Troubleshooting .................................................................................. 33

6 wc_bo5000187821_03TOC.fm

Table of Contents PS3 1500 / PS3 2200

6 Technical Data 34

6.1 Standard Specifications .......................................................................34

6.2 Operating Specifications (60 Hz) .........................................................35

7 Schematics 36

8 AEM Safety Manual 39

PS3 1500 / PS3 2200 Safety Information

wc_si000036gb.fm 7

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and

NOTE signal words which must be followed to reduce the possibility

of personal injury, damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a

situation which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f

To avoid death or serious injury from this type of hazard, obey all safety messages that

follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f

To avoid possible death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f

To avoid possible minor or moderate injury from this type of hazard, obey all safety

messages that follow this signal word.

Safety Information PS3 1500 / PS3 2200

8 wc_si000036gb.fm

1.2 Machine Description and Intended Use

This machine is a submersible water pump. The Wacker Neuson

Submersible Pump consists of an electric motor, an impeller, a strainer,

and a metal casing with ports for water suction and discharge. Power is

supplied to the pump through a corded plug or a hard-wired connection,

depending on the installation. The operator connects hoses to the pump

and routes them so that water is pumped from the work area and

discharged into an appropriate location.

This machine is intended to be used for general de-watering applications.

This machine is intended for the pumping of clear water, or water

containing solids up to the size stated within the products specifications,

and up to the flow, head, and suction lift limits also stated within the

product specifications.

This machine has been designed and built strictly for the intended use

described above. Using the machine for any other purpose could

permanently damage the machine or seriously injure the operator or other

persons in the area. Machine damage caused by misuse is not covered

under warranty.

The following are some examples of misuse:

• Pumping flammable, explosive, or corrosive fluids

• Pumping hot or volatile fluids that result in pump cavitation

• Operating the pump outside of product specifications due to

incorrect diameter hoses, incorrect length hoses, other inlet or

outlet restrictions, or excessive suction lift or head

• Using the machine as a ladder, support, or work surface

• Using the machine to carry or transport passengers or equipment

• Operating the machine outside of factory specifications

• Operating the machine in a manner inconsistent with all warnings

found on the machine and in the Operator’s Manual.

This machine has been designed and built in accordance with the latest

global safety standards. It has been carefully engineered to eliminate

hazards as far as practicable and to increase operator safety through

protective guards and labeling. However, some risks may remain even

after protective measures have been taken. They are called residual

risks. On this machine, they may include exposure to:

• Electric shock from improper electrical connections or high

voltage

• Personal injury from improper lifting techniques

• Projectile hazard from discharge

PS3 1500 / PS3 2200 Safety Information

wc_si000036gb.fm 9

To protect yourself and others, make sure you thoroughly read and

understand the safety information presented in this manual before

operating the machine.

Operator qualifications

Only trained personnel are permitted to start, operate, and shut down

the machine. They also must meet the following qualifications:

• have received instruction on how to properly use the machine

• are familiar with required safety devices

The machine must not be accessed or operated by:

•children

• people impaired by alcohol or drugs

Personal Protective Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while

operating this machine:

• Close-fitting work clothes that do not hinder movement

• Safety glasses with side shields

• Hearing protection

• Safety-toed footwear

Replacement parts

When replacement parts are required for this machine, use only

Wacker Neuson replacement parts or those parts equivalent to the

original in all types of specifications, such as physical dimensions,

type, strength, and material.

1.3 Operating and Electrical Safety

To reduce risk of electric shock, connect only to a properly grounded,

grounding-type receptacle.

Risk of electric shock—this pump has not been investigated for use in

swimming pool areas.

An acceptable motor-control switch shall be provided at the time of

installation according to local codes and regulations.

To reduce risk of electric shock, follow instructions in this manual for

proper installation.

CAUTION: This pump may automatically restart. Prior to working on

the pump or control panel, all supply circuits must be disconnected.

CAUTION: Risk of shock—do not remove cord and strain relief.

WARNING

Safety Information PS3 1500 / PS3 2200

10 wc_si000036gb.fm

1.4 Service Safety

Service training

Before servicing or maintaining the machine:

• Read and understand the instructions contained in all manuals

delivered with the machine.

• Familiarize yourself with the location and proper use of all

controls and safety devices.

• Only trained personnel shall troubleshoot or repair problems

occurring with the machine.

• Contact Wacker Neuson for additional training if necessary.

When servicing or maintaining this machine:

• Do not allow improperly trained people to service or maintain the

machine. Personnel servicing or maintaining the machine must

be familiar with the associated potential risks and hazards.

Personal Protective Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while

servicing or maintaining this machine:

• Close-fitting work clothes that do not hinder movement

• Safety glasses with side shields

• Hearing protection

• Safety-toed footwear

In addition, before servicing or maintaining the machine:

• Tie back long hair.

• Remove all jewelry (including rings).

Replacing parts and labels

• Replace worn or damaged components.

• Replace all missing and hard-to-read labels.

• When replacing electrical components, use components that are

identical in rating and performance as the original components.

• When replacement parts are required for this machine, use only

Wacker Neuson replacement parts or those parts equivalent to

the original in all types of specifications, such as physical

dimensions, type, strength, and material.

PS3 1500 / PS3 2200 Safety Information

wc_si000036gb.fm 11

1.5 Labels

A nameplate listing the model number, item number,

revision number, and serial number is attached to each

unit. Please record the information found on this nameplate

so it will be available should the nameplate become lost or

damaged. When ordering parts or requesting service

information, you will always be asked to specify the model

number, item number, revision number, and serial number

of the unit.

CAUTION

Do not attempt to operate this product before reading the

Operator’s Manual and understanding its contents.

Mishandling of this product may result in explosion, fire, or

electrical shock.

 Do not pull on the power cord or use the power cord to lift

the pump.

 Always use a dedicated ground leakage circuit breaker.

 Be sure to install the ground wire securely.

 Be sure to disconnect the power supply before handling

or inspecting the pump.

Never insert your hand into the pump inlet holes while the

pump is connected to the power supply.

Menomonee Falls, WI 53051 USA

Model

Item No. Rev.

Serial No.

VHz

kWkgMax. L/minMax. m

MADE IN

JAPAN

HPlbsMax. GPMMax.

ft

&

86

/

,

6

7

(

'

5

Phase

C22.2 No. 108-M89



Conforms to UL Std.778

Cert . to CAN/CSA

Std.

Amp.

Ma n. Y/M

Y THERMALL PROTECTED

INDOORS OR OUTDOORS

CSA ENCLOSURE

3

Wacker Neuson Production Americas LLC

Lifting and Transporting PS3 1500 / PS3 2200

12 wc_tx001959gb.fm

2 Lifting and Transporting

Do not under any circumstances install or move the pump by

suspending it from the cable assembly. The cable may be damaged,

causing electrical leakage, shock, or fire.

When installing the pump, pay close attention to its center of gravity

and weight. If it is not lowered into place correctly, it may fall and be

damaged or cause injury.

When transporting the pump by hand, be sure to employ manpower

commensurate with the weight of the pump. To avoid back injury when

lifting the pump, bend the knees to pick it up rather than bending your

back only.

Avoid dropping the pump or other strong impact. Lift the pump by

holding it firmly with the hands or by attaching a rope or chain to the

handle.

WARNING

CAUTION

PS3 1500 / PS3 2200 Installation

wc_tx001974gb.fm 13

3 Installation

3.1 Components

Ref. Description Ref. Description

1. Coupling 9. Dust Seal

2. Mechanical Seal 10. Wear Ring

3. Gasket 11. Oil Housing

4. Sleeve 12. Impeller

5. Cable Assembly 13. Volute

6. Lifting Handle 14. Strainer

7. Lubricant 15. Retainer Plate

8. Oil Plug

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

wc

_

gr000321

Installation PS3 1500 / PS3 2200

14 wc_tx001974gb.fm

3.2 Preparing the Machine for First Use

When the pump is delivered, first perform the following checks:

• Inspection

While unpacking, inspect the product for damage during shipment, and

make sure all bolts and nuts are tightened properly.

• Specification check

Check the model number to make sure it is the product that was

ordered. Be certain it is the correct voltage and frequency.

Note: If there is any problem with the product as shipped, contact your

nearest dealer or Wacker Neuson representative at once.

• Product specifications

Do not operate this product under any conditions other than those for

which it is specified. Failure to observe this precaution can lead to

electrical shock, current leakage, fire, water leakage or other

problems.

3.3 Application Area

If the pump is used to drain a swimming pool, the pump must be

connected to a Ground Fault Interrupter (GFI).

If the pump is used in fountains, the pump must be connected to a

Ground Fault Interrupter (GFI).

The pump must not be used when people are in the water.

Leakage of pump lubricants may cause pollution of water.

Proper plug must be provided according to local codes and standards.

Refer to wiring diagram.

Do not use this pump in liquids other than water, such as oil, salt water,

or organic solvents.

Use with a power supply voltage within ±5% of the rated voltage.

Do not use in water temperatures outside the range of 0–40°C

(32–104°F) which can lead to failure, current leakage or shock.

Do not use in the vicinity of explosive or flammable materials.

Use only in fully assembled state.

Note: Consult your local dealer or Wacker Neuson representative

before using with any liquids other than those indicated in this

document.

CAUTION

WARNING

PS3 1500 / PS3 2200 Installation

wc_tx001974gb.fm 15

3.4 Maximum Allowable Water Pressure

NOTICE: Do not use at greater than the water pressure shown, which

can damage the pump resulting in electrical leakage and electrical

shock.

3.5 Preparing for installation

Before installing the pump at a work site, you will need to have the

following tools and instruments ready:

• Insulation resistance tester (megohmmeter)

• AC voltmeter

• AC ammeter (clamp-on type)

• Bolt and nut tighteners

• Power supply connection tools (screwdriver or box wrench)

Note: Please also read the instructions that come with each of the test

instruments.

Model Maximum Allowable Water Pressure

PS 3 1500/2200 0.3 MPa (43 PSI)

Installation PS3 1500 / PS3 2200

16 wc_tx001974gb.fm

Notes

PS3 1500 / PS3 2200 Installation

wc_tx001974gb.fm 17

3.6 Checks to Make Before Installation

With the megohmmeter, measure the insulation resistance between

each of the power wires and grounding wire to verify the insulation

resistance of the motor.

Reference insulation resistance: 20MW or greater

Note: The reference insulation resistance (20MW or greater) is the

value when the pump is new or has been repaired. For the reference

value after installation, see Maintenance and Inspection.

DO NOT measure the insulation resistance with insulation resistance

tester for the following parts. It will cause damage (Model PSA 2 500).

Improper ways to measure insulation resistance

1 Between the plug prongs.

2 Between the electrodes on the level relay unit.

3 Between the electrodes on the level relay unit and the plug prongs.

CAUTION

1

2

wc

_

gr000258

3

Installation PS3 1500 / PS3 2200

18 wc_tx001974gb.fm

3.7 Changing the Operating Voltage

The operating voltage of the motor can be changed from 110V to

220V depending on the available power source.

Requirements

• Pump disconnected from the power source

• Hand tools (screwdriver and wrench)

Procedure

Follow the procedure below to change the operating voltage of the

motor.

3.7.1 Remove the four bolts (c), lockwashers (d), and flat washers (e) that

fasten the housing cover (j) to the motor bracket.

3.7.2 Carefully lift the housing cover.

NOTICE: Avoid entangling the power cord lead wires with internal compo-

nents such as the centifugal switch (p) or the capacitor (o). Be careful not to

damage the O-ring (w) while lifting the housing cover.

3.7.3 Support the housing cover so that it allows access to the terminal box

(q).

WARNING

Electric shock hazard.

f Ensure that the pump is disconnected from the power source before changing

the operating voltage.

wc_gr008856

p

PS3 1500 / PS3 2200 Installation

wc_tx001974gb.fm 19

3.7.4 Remove the plastic cover (not shown) from the front face of the

terminal box. Using a screwdriver, detach and move the lead wires as

needed to configure the operating voltage.

3.7.5 Reinstall the plastic cover.

3.7.6 Make sure that the O-ring (w) and gasket (x) are properly seated.

NOTICE: Replace the O-ring or gasket if either shows signs of damage or

wear.

3.7.7 Lower the housing cover onto the motor bracket. Align the housing

cover as shown.

3.7.8 Fasten the housing cover to the motor bracket.

Result

The operating voltage of the motor has now been changed.

Desired

voltage

Terminal block Wire locations

110V Upper L2 and T2 together at position 2 (from left)

Lower T1 and T3 together at position 3 (from left)

220V Upper T2 at position 5 (from left)

Lower T1 at position 4 (from left)

T3 at position 5 (from left)

Installation PS3 1500 / PS3 2200

20 wc_tx001974gb.fm

3.8 Precautions in Installation

3.8.1 The pump is supplied with a threaded discharge fitting. Tighten hose

coupling or discharge pipe securely and with proper gaskets.

3.8.2 Install the pump in a location with sufficient water level, where water

collects readily.

Note: See Operation (“Operating Water Level”) for the water level

necessary for operation. The discharge end of the hose should be

located higher than the water surface. If the end of the hose is

submerged, water may flow back to the pump when the pump is

stopped; and if the hose end is lower than the water surface, water may

overflow when the pump is turned off.

3.8.3 The hose should be run as straight as possible, since excessive

bending will hinder the water flow, preventing sufficient lift, and can

even cause the hose to become clogged with earth. If the hose is

crimped near the pump, air can become trapped in the pump and

cause idle running.

If large quantities of earth are sucked up, damage resulting from

friction in the pump can lead to electrical leakage and shock.

NOTICE: When the pump is installed at a work site, make sure the

hose is connected in such a way as to ensure proper drainage.

Otherwise water may leak out and cause damage to surrounding walls

or flooring, or to equipment.

3.8.4 Use the pump in the upright position. To prevent the strainer from

becoming submerged in mud, causing it to suck in sand or debris,

mount it on a block or other firm base.

3.8.5 If used in a permanent installation, where the pump is not readily

accessible after installation, please contact Wacker Neuson for a

duplicate nameplate to be installed at the wellhead or on the control

box so that it will be readily visible.

Do not operate the pump dry. Doing so will prevent the pump from

attaining its full potential and may also damage the pump and lead to

a short and electrical shock.

CAUTION

La page charge ...

Wacker Neuson PS31500 Manuel utilisateur

Ce manuel convient également à

Wacker Neuson PS31500 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents