KitchenAid 760-0023-LP Le manuel du propriétaire

BUILT-IN GRILL CABINET SIDE BURNER

Installation Instructions and Use & Care Guide

For questions about features, operation/performance, parts, accessories or service, call: 1-877-373-2301

or visit our website at www.kitchenaidgrills.com

Languages spoken: English, Spanish, French 8 a.m.-5 p.m., PST. Monday-Friday.

QUEMADOR LATERAL PARA GABINETE

DE ISLA CONSTRUIDA

Instrucciones de instalación y manual de uso y cuidado

Para consultas respecto a características, funcionamiento, rendimiento, piezas, accesorios o servicio técnico, llame al: 1-877-373-2301

o visite nuestro sitio de internet en www.kitchenaidgrills.com

Lenguages ablados: Ingles, Espanol y Frances de 8 a.m.-5 p.m., PST. Lunes-Viernes.

GRILL ENCASTRÉ DANS LE CABINET

AVEC UN BRÛLEUR LATÉRAL

Instructions d’installation et guide d’utilisation et d’entretien

Pour des questions à propos des caractéristiques, du fonctionnement/rendement, des pièces, des accessoires ou du service,

composer le: 1-877-373-2301

ou visiter notre site web www.kitchenaidgrills.com

Langues parlées: anglais , espagnol, français entre 8 h et 17 h, HNP, du lundi au vendredi.

Table of Contents/Índice/Table des matières................................................................................. 2

19000655A1

Keep this manual for future reference.

Conserve el presente manual para consultas futuras.

Conserver ce manuel à titre de référence ultérieure.

760-0023 (LP) / 770-0023 (NG)

TABLE OF CONTENTS

OUTDOOR BUILT-IN SIDE BURNER SAFETY …….….........3

PACKAGE PARTS LIST .......................................................5

ASSEMBLY INSTRUCTIONS .…………………....……….……6

INSTALLATION REQUIREMENTS ………………………....11

Tools and Parts ……………………….….…….………......…...11

Location Requirements ……………………………...………12

Product Dimensions ………………………………..……….…12

Built-In Outdoor Side Burner Enclosure ….…….…..….……..12

Cabinet Cutout Dimensions………………….…………………13

Gas Supply Requirements ……………...………………………14

Gas Connection Requirements …………………..…..……..…15

INSTALLATION INSTRUCTIONS……………….............…...16

Make Gas Connection…………………….............……………16

GAS CONVERSION …………………………….............…...18

Gas Connection to Natural Gas ………………………......…...18

Tools and Parts for Gas Conversion …………………......…...18

Conversion from LP Gas to Natural Gas …...…………......….19

USING YOUR OUTDOOR SIDE BURNER …….............…...21

Lighting the Side Burner ………….……………………......…...21

OUTDOOR SIDE BURNER CARE ..….……….………………22

General Cleaning ………….………….………………......…...22

TROUBLESHOOTING ...........................................................23

ASSISTANCE …………………………………………….…..…23

Accessories………………………………………………...……..23

WARRANTY ……………………………………….…………….24

REPLACEMENT PARTS………………………………...….…61

TABLE DES MATIÈRES

SÉCURITÉ DU BRÛLEUR LATERAL ............................... 44

LISTE DES PIÈCES DE L’EMBALLAGE................................5

CONSIGNES POUR L’ASSEMBLAGE……………….......……6

EXIGENCES D’INSTALLATION …………………..…….....…46

Outils et pieces ………………………………………..…………46

Exigences d'emplacement ………………………...…………47

Dimensions du produit ……………………………………...…..47

Enceinte du brûleur encastré d'extérieur ………………….….47

Dimensions de l'ouverture à découper dans le placard …….48

Spécifications de l‘alimentation en gaz ……………………….49

Exigences concernant le raccordement au gaz …………...…50

INSTRUCTIONS D’INSTALLATION …….…………….……...51

Installation du brûleur d'extérieur encastré…..………..……...51

CONVERSIONS POUR CHANGEMENT DE GAZ ……...…..53

Raccordement du gaz au gaz naturel ………………………....53

Outils et pièces pour conversion de gaz ………………..…...53

Conversion de gaz propane à gaz naturel …………..…....….54

UTILISATION DU BRÛLEUR LATÉRAL D'EXTÉRIEUR ….56

Allumage du Brûleur Latéral ……..….…..….….….….……......56

ENTRETIEN DU BRÛLEUR D’EXTÉRIEUR ….……………..57

Nettoyage Général ……...………….………..….….….……......57

DÉPANNAGE..........................................................................58

ASSISTANCE………………………………….…..………….…58

Accessoires .……………………………………………...……..58

GARANTIE……………………………………..……..……...…..59

PIÈCES DE RECHANGE …………………..………………...61

ÍNDICE

SEGURIDAD DEL QUEMADOR DE USO EXTERIOR .........26

LISTA DE CONTENIDO DEL PAQUETE……………….....…..5

INSTRUCCIONES DE ENSAMBLAJE ….………..…..………..6

REQUISITOS DE INSTALACIÓN…………..………….…....28

Herramientas y piezas ….…….….………………….….……....28

Requisitos de ubicación …………………………….….……....29

Medidas del producto …………………………….……...……..29

Recinto del quemador lateral

para gabinete de isla construida ………………………………29

Dimensiones del corte del armario ………………...................30

Requisitos del suministro de gas …………………..……….31

Requisitos para la conexión de gas……………………..……..32

INSTRUCCIONES DE INSTALACIÓN ………….............…...34

Instalación del Quemador …………………………………..…..34

Conexión del suministro de gas ………..……….…………...34

CONVERSIONES DE GAS …………………………......….….36

Conexión de gas a gas natural ..........................................….36

Herramientas y piezas para la conversión de gas …………36

Conversión de gas LP a gas natural ………….…….…………37

USO DEL QUEMADOR LATERAL …….………..…..…..39

Encendido del Quemador Latéral ….…………………...……..39

CUIDADO DEL QUEMADOR PARA EXTERIORES ….……40

Limpieza general …………..……………………………...……..40

SOLUCIÓN DE PROBLEMAS...............................................41

ASISTENCIA…………………………………………..……..…..41

Accesorios ………………………………………………...……..41

GARANTÍA ……………………………………………..……......42

PIEZAS DE REPUESTO ……………………………............…61

2

OUTDOOR BUILT-IN SIDE BURNER SAFETY

DANGER

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open lid.

4. If odor continues, keep away from the

appliance and immediately call your gas

supplier or your fire department.

WARNING

1. Do not store or use gasoline or other

flammable liquids or vapors in the

vicinity of this or any other appliance.

2. An LP cylinder not connected for use

shall not be stored in the vicinity of this

or any other appliance.

3

IMPORTANT: This grill is manufactured for outdoor use only. For grills that are to be used at elevations above 2,000 ft (609.6 m)

orifice conversion is required. See “Gas Supply Requirements” section. It is the responsibility of the installer to comply with the

minimum installation clearances specified on the model/serial rating plate. The model/serial rating plate for freestanding models can

be found on the left-hand cabinet door.

In the State of Massachusetts, the following installation instructions apply:

◼ Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

◼ If using a ball valve, it shall be a T-handle type.

◼ A flexible gas connector, when used, must not exceed 3 feet.

CALIFORNIA RESIDENTS ONLY - WARNING:

This product and the fuels used to operate this product (liquid propane), and the products of

combustion of such fuels, can expose you to chemicals including benzene, which is known

to the State of California to cause cancer and reproductive harm.

For more information go to: www.P65Warnings.ca.gov.

WARNING: To reduce the risk of fire, electrical shock,

Injury to persons, or damage when using the outdoor cooking

gas appliance, follow basic precautions, including the following:

◼ Do not install portable or built-in outdoor cooking gas

appliances in or on a recreational vehicle, portable trailer,

boat or in any other moving installation.

◼ Always maintain minimum clearances from combustible

construction, see “ Location Requirements” section.

◼ The outdoor cooking gas appliance shall not be located

under overhead unprotected combustible construction.

◼ This outdoor cooking gas appliance shall be used only

outdoors and shall not be used in a building, garage, or

any other enclosed area.

◼ Keep any electrical supply cord and fuel supply hose away

from any heated surfaces.

◼ Keep outdoor cooking gas appliance area clear and free

from combustible material, gasoline and other flammable

vapors and liquids.

◼ Do not obstruct the flow of combustion and ventilation air.

Keep the ventilation openings of the cylinder enclosure

free and clear from debris.

◼ Inspect the gas cylinder supply hose before each use of

the outdoor cooking gas appliance. If the hose shows

excessive abrasion or wear, or is cut, it MUST be replaced

before using the outdoor cooking gas appliance. Contact

your dealer and use only replacement hoses specified for

use with the outdoor cooking gas appliance.

◼ Visually check the burner flames.

They should be blue. Slight

yellow tipping is normal for

LP gas. The flames should

be approximately 1" (2.5 cm) high.

◼ Check and clean burner/venturi tube for insects and insect

nest. A clogged tube can lead to fire under the outdoor

cooking gas appliance.

IMPORTANT SAFETY INSTRUCTIONS

◼ The LP gas supply cylinder to be used must be:

- constructed and marked in accordance with the

Specification for LP Gas cylinders of the U.S.

Department of Transportation (DOT) or the National

Standard of Canada, CAN/CSA-B339, Cylinders,

Spheres, and Tubes for Transportation of Dangerous

Goods; and Commission.

- provided with a listed overfilling prevention device.

- provided with a cylinder connection device compatible

with the connection for outdoor cooking gas appliances.

◼ Always check connections for leaks each time you connect

and disconnect the LP gas supply cylinder. See

“Installation Instructions” section.

◼ When the outdoor cooking gas appliance is not in use, the

gas must be turned off at the supply cylinder.

◼ Storage of an outdoor cooking gas appliance indoors is

permissible only if the cylinder is disconnected and

removed from the outdoor cooking gas appliance.

◼ Cylinders must be stored outdoors and out of the reach of

children and must not be stored in a building, garage, or

any other enclosed area.

◼ The pressure regulator and hose assembly supplied with

the outdoor cooking gas appliance must be used. A

replacement pressure regulator and hose assembly

specific to your model is available from your outdoor

cooking gas appliance dealer.

◼ Gas cylinder must include a collar to protect the cylinder

valve.

◼ For appliances designed to use a CGA791 connection:

Place a dust cap on cylinder valve outlet whenever the

cylinder is not in use. Only install the type of dust cap on

the cylinder va`lve outlet that is provided with the cylinder

valve. Other types of caps or plugs may result in leakage

of propane.

If the following information is not followed exactly, a fire causing

death or serious injury may occur.

◼ Do not store a spare LP gas cylinder under or near this

outdoor cooking gas appliance.

◼ Never fill the cylinder beyond 80 percent full.

SAVE THESE INSTRUCTIONS

4

7

1

3

Package Parts List

Lista de contenido del paquete

Liste des pièces de l'emballage

2

4

x2

5

5 6

Tools Needed / Herramientas necesarias / Outillage Requis

ASSEMBLY INSTRUCTIONS/INSTRUCCIONES DE ENSAMBLAJE/CONSIGNES POUR L’ASSEMBLAGE

Some parts come

with Screws pre-

installed.

Loosen and tighten

for final assembly.

Algunas partes

vienen con los

tornillos pre

instalados.

Afloje y apriete para

el ensamble final.

Certaines pièces

sont livrées avec les

vis pré-installées.

Desserrez et

resserrez pour

l'assemblage final.

6

1.

1

Hardware package list / Lista de piezas / Liste de pièces

A x5

B

x4

Flat Washer

Arandela plana

Rondelle plate

5/32"

Truss Head Screw

Tornillo de cabeza

de armadura

Vis à tête bombée

5/32 - 32 x 3/8"

2.

3.

7

2

4.

5.

8

5

4

3

6.

7.

9

6

A

x1

8.

10

A

x4

B

x4

7

◼

Natural gas regulator (marked “Natural Gas Regulator”)

◼ 10 ft (3.0 m) PVC flexible gas supply hose with quick

connector

◼ 5.9 in. NG regulator hose

◼ 6 mm wrench

◼ 6 mm nut driver

◼ Hex key

◼

Tape Measure

◼

Small, flat-blade screwdriver

◼

Flat-blade screwdriver

◼

#2 and #3 Phillips screwdriver

◼

Level

◼

Wrench or pliers

◼

Pipe wrench

◼

Scissors or cutting pliers (to remove tiedowns)

◼

Noncorrosive leak-detection solution

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Configuration: Stand-Alone Side Burner (760-0023)

Tools needed

Parts Supplied for 20 lb LP Gas Installation

◼ Gas pressure regulator/hose assembly set for 11" WCP LP gas

◼ LP gas fuel tank tray

Parts Supplied for Conversion to Natural Gas

◼ 1.70 mm Natural gas orifice for side burner (Model 760-0023)

Parts Needed for Conversion to Natural Gas

◼ Natural gas conversion kit (Order Part Number 710-0003). Natural gas conversion kit includes:

◼ Gas line shut off valve

◼ ½" male pipe thread nipple for connection to pressure regulator

◼ LP gas-resistant pipe-joint compound

◼ CSA design-certified outdoor flexible stainless steel appliance connector (4-5 ft [1.2-1.5 m]) or rigid gas supply line as needed

11

Location Requirements

Select a location that provides minimum exposure to wind and

traffic paths. The location should be away from strong draft

areas.

Do not obstruct flow of combustion and ventilation air.

Clearance to combustible construction for burner:

◼ A minimum of 36” (92 cm) must be maintained between

the front, sides and back of the burner and any

combustible construction.

◼ A 36” (92 cm) minimum clearance must also be maintained

below the cooking surface, and the burner shall not be

used under overhead combustible construction.

Product Dimensions

Built-In Outdoor

Side Burner Enclosure

The enclosure opening for the built-in outdoor side searing

burner is to be a minimum of 11.5" (29.2 cm) wide x 16.75"

(42.7 cm) long x 7.3" (18.4 cm) deep.

This built-in outdoor side burner is only for installation in a built-

in enclosure constructed only of non-combustible materials.

Non-combustible materials could be brick, firewall or steel. Do

not use wood or other combustible materials for built-in

enclosure.

12

7.3“ (18.4cm)

5.7“

(14.4cm)

9.1“ (23cm)

Cabinet Cutout Dimensions

The illustration below includes cutout dimensions and minimum spacing requirements. The illustration is for reference. The design

of your cabinet layout can be personalized, but the dimensions for the cutouts and minimum spacing must be followed.

Counter or support surfaces must be level.

The installation of this side burner must conform with local codes or, in the absence of local codes, with either the National Fuel

Gas Code, ANSI Z223.1/NPFA 54, Natural Gas and Propane Installation Code, CSA B149.1, or Propane Storage and Handling

Code, B149.2.

NOTE: The outdoor side buner drops into the enclosure opening and is supported by its side flanges. Do not use a bottom support.

◼ The island must be vented in one of the 2 following ways:

A 90°or a 180°ventilation in the island to ensure that air

flows through the island at either 90°or 180°.

◼ Any enclosure for built-in installation is to have at least

one ventilation opening on an exposed exterior side

located within 2½" (6.0 cm) of the top and is to be a

minimum of 20 in.

2

(129.0 cm

2

). One ventilation opening

within 1½" (3.0 cm) of the bottom of the enclosure, and the

bottom opening is to be a minimum of 10 in.

2

(64.5 cm

2

).

All vent openings are to be unobstructed. Every opening is

to be a minimum of 1/8" (0.32 cm) wide.

Any enclosure is to be ventilated by openings at both the top

and lower levels of the enclosure. The following information is

the minimum for proper ventilation of your island construction.

◼ There should be a minimum of 1 7/8" (4.4 cm) of clearance

from the bottom of the main burner bowl assembly island

for proper ventilation.

NOTE: There should be no solid surface underneath the

firebox portion of the side burner.

◼ A minimum of 3" (7.6 cm) is required between the back of

the side burner and any noncombustible materials. A

minimum of 36" (92 cm) is required between the back of

the side burner and any combustible material.

Built-in Outdoor Side Burner Enclosure Ventilation for LP Gas

13

◼ To ensure that the side burner operates properly, it is

recommended that the island have ventilation on all 4

sides as shown in the following illustration. The ventilation

holes should be as diagrammed to ensure adequate

ventilation for your side burner and island.

◼ Proper ventilation is a required based on the above

mentioned specifications for your side burner to operate

properly.

Observe all governing codes and ordinances.

IMPORTANT: This installation must conform with all local

codes and ordinances. In the absence of local codes,

installation must conform with American National Standard,

National Fuel Gas Code ANSI Z223.1 - latest edition or

CAN/CGA B149.1 – latest edition.

IMPORTANT: The side burner must be connected to a

regulated gas supply.

Refer to the model/serial rating plate for information on the type

of gas that can be used. If this information does not agree with

the type of gas available, check with your local gas supplier.

Gas Conversion:

No attempt shall be made to convert the side burner from the

gas specified on the model/serial rating plate for use with a

different gas type without consulting the serving gas supplier.

The conversion kit supplied with side burner must be used. See

“Gas Conversions” section for instructions.

Gas Pressure Regulator

A gas pressure regulator with the following pressure settings

must be used with the side burner. The inlet (supply) pressure

to the regulator should be as follows for proper operation:

LP Gas:

Operating pressure: 11" (27.9 cm) WCP

Inlet (supply) pressure: 11" to 14" (27.9 cm to 35.5 cm) WCP

Natural Gas:

Operating pressure: 4" (10.2 cm) WCP

Inlet (supply) pressure: 7" to 14" (17.8 cm to 35.5 cm) WCP

maximum.

Contact local gas supplier if you are not sure about the inlet

(supply) pressure.

Gas Supply Requirements

14

Burner Requirements for High Altitude

Input ratings shown on the model/serial rating plate are for

elevations up to 2,000 ft. (609.6 m).

For elevations above 2,000 ft. (609.6 m), ratings are reduced at

a rate of 4% for each 1,000 ft. (304.8 m) above sea level.

Orifice conversion is required. See “Assistance” section to

order.

Gas Supply Line Pressure Testing

Testing above 1/2 psi (3.5 kPa) or 14" (35.5 cm) WCP

(gauge):

The side burner and its individual shutoff valve must be

disconnected from the gas supply piping system during any

pressure testing of that system at test pressures greater than

1/2 psi (3.5 kPa).

Testing below 1/2 psi (3.5 kPa) or 14" (35.5 cm) WCP

(gauge) or lower:

The side burner must be isolated from the gas supply piping

system by closing its individual manual shutoff valve during any

pressure testing of the gas supply piping system at test

pressures equal to or less than 1/2 psi (3.5 kPa).

Gas Connection Requirements

This side burner is equipped for use with a 20 lb LP gas fuel

tank (fuel tank not supplied). A gas pressure regulator/hose

assembly is supplied.

A. Gas pressure regulator/hose assembly

20 lb LP Gas Fuel Tank

The 20 lb LP gas fuel tank must be mounted and secured.

1. Open cabinet doors (if applicable).

2. Loosen the tank tray locking screw.

3. Place the 20 lb LP gas fuel tank bottom collar into the

mounting hole in the tank tray.

4. Tighten the locking screw against the bottom collar of the

20 lb LP gas fuel tank to secure.

5. Close cabinet doors (if applicable).

Make sure the tank is firmly secured in an upright position.

A

LP Gas Conversion Using a Local LP Gas Supply

If you want to convert to local LP gas supply, contact your local

gas company for specific instructions.

Natural Gas Conversion

Conversion must be made by a qualified gas technician. The

qualified Natural gas technician shall provide the Natural gas

supply to the selected side burner location in accordance with

the National Fuel Gas Code ANSI Z223.1/NFPA 54 - latest

edition, and local codes. For conversion to Natural gas, the

Natural Gas Conversion Kit supplied with the side burner must

be used. See the “Gas Conversions” section.

IMPORTANT: The gas installation must conform with local

codes, or in the absence of local codes, with the National Fuel

Gas Code, ANSI Z223.1/NFPA 54 - latest edition.

The gas supply line shall be equipped with an approved shutoff

valve. This valve should be located in the same area as the

side burner and should be in a location that allows ease of

opening and closing. Do not block access to the shutoff valve.

The valve is for turning on or shutting off gas to the side burner.

A. Gas supply line

B. Shutoff valve “open” position

C. To side burner

B

A. Locking screw

B. Tank tray

C. 20 lb LP gas fuel tank tray

A

C

It is also design-certified by CSA International for local LP gas

supply or for Natural gas with appropriate conversion.

15

NOTE: If side burner is to be converted to Natural gas, follow

instructions in the “Gas Conversions” section.

20 lb LP Gas Fuel Tank

IMPORTANT: A 20 lb LP gas fuel tank must be purchased

separately.

IMPORTANT: The 20 lb LP gas fuel tank must be mounted

and secured.

IMPORTANT: The gas pressure regulator/hose assembly

supplied with the burner must be used. Replacement gas

pressure regulator/hose assembly specific to your model is

available from your outdoor grill dealer.

To Connect the 20 lb LP Gas Fuel Tank:

1. Check that the 20 lb LP gas fuel tank is in the “OFF”

position. If not, turn the valve clockwise until it stops.

2. Check that the 20 lb LP gas fuel tank valve has the proper

type-1 external male thread connections per ANSI Z21.81.

3. Check that the burner control knobs are in the “OFF”

position.

4. Remove any debris and inspect the valve connections,

port, and gas pressure regulator/hose assembly for

damage.

NOTE: Always keep the LP cylinder at 90°(upright) orientation

to provide vapor withdrawal.

◼ Unpack side burner. Remove all packaging materials and

remove side burner from carton.

◼ Place side burner into outdoor enclosure, but leave

enough room in back to connect to gas supply.

INSTALLATION INSTRUCTIONS

Built-in Outdoor Side Burner

Installation

Make Gas Connection

Install 20 lb LP Gas Fuel Tank Tray

The tank tray should be secured to a fixed location that can be

easily accessed and will allow the gas pressure regulator/ hose

assembly to connect to the 20 lb LP gas fuel tank without

kinking or putting strain on the gas pressure regulator/ hose

assembly.

1. Place the tank tray in a location that can be secured using

4 screws (supplied) through the predrilled holes.

2. Use 4 screws to secure the tank tray. The typical location

for a 20 lb LP gas fuel tank is within the enclosure where

the tank can be turned on and off easily.

NOTE: A bracket or shelf (not supplied) that is large enough to

keep a second 20 lb LP gas fuel tank from being stored in the

storage area under the side burner is required to be mounted

inside the island.

16

A. Four 5/32-32 x 3/8” truss head screws

A. Gas pressure regulator/hose assembly

B. 20 lb LP gas fuel tank

To Disconnect the 20 lb LP Gas Fuel Tank:

1. Check that the burner control knobs are in the “OFF”

position and the side burner is cool.

2. Check that the 20 lb LP gas fuel tank is in the “OFF”

position. If not, turn the valve clockwise until it stops.

3. Using your hand, turn the gas pressure regulator/hose

assembly counterclockwise to disconnect to the 20 lb LP

gas fuel tank as shown.

Hand loosen only. Use of a wrench could damage the

quick coupling nut.

4. Place dust cap on cylinder valve outlet whenever the

cylinder is not in use. Only install the type of dust cap on

the valve outlet that is provided with the cylinder valve.

Other types of caps or plugs may result in leakage of

propane.

5. Using your hand, turn the gas pressure regulator/hose

assembly clockwise to connect to the 20 lb LP gas fuel

tank as shown.

Hand tighten only. Use of a wrench could damage the

quick coupling nut.

A. Gas pressure regulator/hose assembly

B. 20 lb LP gas fuel tank

A

B

A. Gas pressure regulator/hose assembly

B. 20 lb LP gas fuel tank

Make sure that the cylinder valve connection device

properly mates with the connection device attached to the

inlet of the pressure regulator.

6. Open the tank valve fully by turning the valve

counterclockwise. Wait a few minutes for gas to move

through the gas line.

7. Before lighting the side burner, test all connections by

brushing on an approved noncorrosive leak-detection

solution. Bubbles will show a leak.

8. If a leak is found, turn the tank valve off and do not use the

side burner. Contact a qualified gas technician to make

repairs.

17

GAS CONVERSIONS

Gas Connection to Natural Gas

This installation must conform with local codes and ordinances.

In the absence of local codes, installations must conform with

either the National Fuel Gas Code ANSI Z223.1 - latest edition,

or CAN/CGAB149.1 Natural Gas and Propane installation

code.

Copies of the standards listed above may be obtained from:

CSA International

8501 East Pleasant Valley Rd.

Cleveland, Ohio 44131-5575

National Fire Protection Association

One Batterymarch Park

Quincy, Massachusetts 02269

6mm

Tools and Parts for Gas Conversion

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

Parts supplied

◼ Natural gas orifices

Parts needed

◼ Natural gas conversion kit Part Number 710-0003. See

“Assistance” section to order. The conversion kit includes:

◼ Natural gas regulator 4" W.C. (marked “Natural Gas

Regulator”)

◼ 10 ft (3.0 m) Natural gas hose with quick connector

◼ 5.9" (150 mm) Natural gas regulator hose

◼ 6 mm nut driver

◼ 6 mm wrench

◼ Hex key

IMPORTANT: Gas conversions must be done by a qualified

installer. Before proceeding with conversion, shut off the gas

supply to the side burner.

18

Conversion from LP Gas to

Natural Gas

Orifice Change and the Installation of the NG regulator

1. Turn off the main gas supply valve.

2. Disconnect 20 lb LP gas fuel tank (if present).

3. Turn off burner control valve.

4. Use screwdriver to remove screw holding the corrugated

pipe connector to the enclosure.

5. Use adjustable wrench to remove hose and regulator from

corrugated pipe connector.

6. Remove side burner cooking grid and burner cover.

7. Remove igniter junction wire from electronic igniter module.

19

8. Remove 3 screws off the front baffle.

9. Lift up front baffle away from burner.

10. Use a 6 mm socket and wrench or 6 mm nut driver to

remove the LP gas orifice from the end of gas valve.

11. Use a 6 mm socket and wrench or 6 mm nut driver to

install NG gas orifice to the end of gas valve.

Record Conversion

The LP appliance nameplate is located on the front side of the

burner firebox. Once converted, place the NG appliance

nameplate over the current LP appliance nameplate.

In the last page of the Use and Care Guide, write “Converted to

Natural Gas”. Also record the conversion date and the

technician/company that performed the conversion.

20

12. Reinstall front baffle to burner.

IMPORTANT: Check that the orifice is properly installed

inside of the side burner gas valve.

13. Install the 3 screws.

14. Insert igniter junction wire from electronic igniter module.

15. Replace side burner cooking grid and burner cover.

16. Use an adjustable wrench to install Natural gas pressure

regulator and corrugated pipe to the corrugated pipe

connector.

17. Connect the brass connector on one end of the 10 ft (3.0

m) PVC flexible gas supply hose to the Natural gas

pressure regulator (A).

18. Connect the quick connector on the other end of the 10 ft

(3.0 m) PVC flexible gas supply hose to the rigid Natural

gas supply pipe (B).

19. Use screwdriver to install screw to hold the corrugate

connector to the enclosure.

B

A

La page charge ...

KitchenAid 760-0023-LP Le manuel du propriétaire

KitchenAid 760-0023-LP Le manuel du propriétaire

dans d''autres langues

Documents connexes