GE Appliances WSLS1500 Manuel utilisateur

ge.com
WSLP1500
WSLS1500
Owner’s Manual &
Installation Instructions
Washers
175D1807P628     49-90361-1   12-08 JR
Safety Information . . . . . . . . . . . 2, 3
Operating Instructions
Control and Indicator Settings  . . . . . .5, 6
Loading and Using the Washer . . . .7, 8
Special Washer Features  . . . . . . . . . . . .4
Installation Instructions
Alcove or Closet Installation  . . . . . . . 12
Electrical Requirements  . . . . . . . . . . . 10
Grounding Instructions  . . . . . . . . . . . . 10
Installation Requirements . . . . . . . . . . . 9
Leveling the Washer  . . . . . . . . . . . . . . 10
Washer Connections for
Portable Model  . . . . . . . . . . . . . . . . 13–16
Washer Connections for
Stationary Model  . . . . . . . . . . . . . . 11, 12
Troubleshooting Tips
Before You Call For Service . . . . . 17–20
Status Indicators  . . . . . . . . . . . . . . . . . . 17
Consumer Support
Consumer Support  . . . . . . . Back Cover
Ownership Registration for
Customers in Canada Only . . . . .21, 22
Warranty for Customers
in Canada . . . . . . . . . . . . . . . . . . . . . . . . .24
Warranty for Customers
in the U.S.A.  . . . . . . . . . . . . . . . . . . . . . . .23
Write the model and serial 
numbers here:
#
#
You can find them on a label 
on the back of the washer.
Laveuses
Lavadoras
Manuel d’utilisation 
et d’installation
Manual del propietario 
e instalación
La section française commence à la page 25
La sección en español empieza en la página 49

2

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

Consumer Support Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

■ Install or store where it will not be exposed

to temperatures below freezing or exposed

to the weather, which could cause permanent

damage and invalidate the warranty.

■ Properly ground washer to conform with all governing

codes and ordinances. Follow details in Installation

Instructions.

WARNING!

For your safety, the information in this manual must be followed to minimize the risk

of fire or explosion, electric shock, or to prevent property damage, personal injury or

loss of life.

The instructions in this manual and all other literature included with this washer are

not meant to cover every possible condition and situation that may occur. Good, safe

practices and caution MUST be applied when installing, operating and maintaining

any appliance.

WATER HEATER SAFETY

Under certain conditions, hydrogen gas may be produced in a water heater that has not been used for two weeks

or more. Hydrogen gas can be explosive under these circumstances.

If the hot water has not been used for two weeks or more, prevent the possibility of damage or injury by

turning on

all hot water faucets and allowing them to run for several minutes. Do this before using any electrical

appliance

which is connected to the hot water system. This simple procedure will allow any built-up hydrogen

gas to escape. Since the gas is flammable, do not smoke or use an open flame or appliance during this process.

PROPER INSTALLATION

This washer must be properly installed and located in accordance with the Installation Instructions before it is used.

■ Keep the area underneath and around your

appliances free of combustible materials such as

lint, paper, rags and chemicals.

■ Do not leave the washer door open. An open door

could entice children to hang on the door or crawl

inside the washer.

■ Close supervision is necessary if this appliance is

used by or near children. Do not allow children to

play on, with or inside this or any other appliance.

YOUR LAUNDRY AREA

3

Consumer Support

Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

ge.com

■ Never reach into washer while it is moving.

Wait until the machine has completely stopped

before opening the door.

■ Do not mix chlorine bleach with ammonia

or acids such as vinegar and/or rust remover.

Mixing different chemicals can produce a toxic

gas which may cause death.

■ Do not wash or dry articles that have been

cleaned in, washed in, soaked in or spotted

with combustible or explosive substances (such as

wax, oil, paint, gasoline, degreasers, dry-cleaning

solvents, kerosene, etc.) which may ignite or

explode. Do not add these substances to the

wash water. Do not use or place these substances

around your washer or dryer during operation.

■ The laundry process can reduce the flame

retardancy of fabrics. To avoid such a result,

carefully follow the garment manufacturer’s

wash and care instructions.

■ To minimize the possibility of electric shock,

unplug this appliance from the power supply

or disconnect the washer at the building’s

distribution panel by removing the fuse or

switching off the circuit breaker before attempting

any maintenance or cleaning. NOTE: Pressing the

power button does NOT disconnect the appliance

from the power supply.

■ Never attempt to operate this appliance

if it is damaged, malfunctioning, partially

disassembled, or has missing or broken parts,

including a damaged cord or plug.

WHEN USING THE WASHER

■ Turn off water faucets to relieve pressure on

hoses and valves and to minimize leakage if

a break or rupture should occur. Check the

condition of the fill hoses; GE recommends

changing the hoses every 5 years.

■ Before discarding a washer, or removing it

from service, remove the washer door to prevent

children from hiding inside.

■ Do not attempt to repair or replace any part of

this appliance unless specifically recommended

in this Owner’s Manual, or in published user-repair

instructions that you understand and have the

skills to carry out.

■ Do not tamper with controls.

WHEN NOT IN USE

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

Use this

appliance

only for its

intended

purpose as

described in

this Owner’s

Manual.

4

Special washer features.

Detergent and Fabric Softener Dispenser Drawer

The detergent and fabric softener dispensers

will automatically release their contents at

the proper time during the cycle.

To Use the Detergent Dispenser:

Add measured detergent to the dispenser.

Make sure detergent is spread evenly and

is level.

To Use the Fabric Softener Dispenser:

Use only liquid fabric softener. Pour into

dispenser, using amount recommended

on package.

■ Do not fill any higher than the top of the

maximum fill tower.

■ Never pour fabric softener directly on

clothes. It may stain them.

Cleaning the Detergent and Fabric Softener Dispenser Drawer

1. Remove the drawer by opening it fully

then tilting the front of the door down.

Pull out.

2. Rinse the drawer with water. If necessary

use a soft cloth to wipe off any debris.

3. Line up the drawer with the opening and

push the dispenser drawer straight in.

Lint Filter

Clean the lint filter inside the wall of

the wash basket once a week for best

filtering results.

To remove:

Press the tab at the top of the filter and

pull out.

To clean:

Open the filter. Clean the filter with

a toothbrush.

Maximum

Fill Tower

Before starting the washer:

• Load the laundry in the washer.

• Add the detergent and fabric softener to the dispenser drawer.

Consumer Support

Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

Installation

Instructions

Safety Instructions

Operating Instructions

Consumer SupportTroubleshooting TipsOperating Instructions

Safety Instructions

Installation

Instructions

EXTRA LARGE

LARGE

SOAK COLORS

WHITES

DELICATES

SPEED WASH

LOAD SENSING

CUSTOM CYCLE

WASH

RINSE

SPIN

COLD

HOT

WARM

LO

C

K

H

OL

D

3

SECS

T

O

LOCK/

UN

LOCK

C

ON

T

R

OL

S

MEDIUM

SMALL

EXTRA SMALL

HEAVY DUTY

EST. MINUTES

REMAINING

TEMP

LOAD

OPTIONS

ULTRA

CLEAN

CYCLES

DELAY WASH

1

to

18 HOURS

POWER

START

PAUSE

About the control and indicator settings. ge.com

POWER ON/OFF

Press the POWER ON/OFF button to turn on the control panel.

WASH OPTIONS

Choose the wash options you would like to include in the cycle. Press the WASH OPTIONS button

until all the options you want to include are lit. More than one option can be selected.

2

1

To Use Automatic One-Touch Washing

START

PAUSE

The LOAD SENSING feature automatically senses the size of your load, fills with the appropriate amount

of water, and calculates the amount of wash time required to complete the cycle.

NOTE: When using the LOAD SENSING feature, it is normal for the pulsator to rotate before water fills

in the tub.

To choose the automatic LOAD SENSING feature, press POWER ON/OFF.

The COLORS indicator light will light up automatically unless you have selected one of the other LOAD

SENSING cycles such as WHITES, DELICATES, SPEED WASH, CUSTOM CYCLE or ULTRA CLEAN.

Then simply press START/PAUSE.

To Choose Your Own Cycle Selections

Before starting the washer:

• Load the laundry in the washer.

• Add the detergent and fabric softener to the dispenser drawer.

Soak+Wash Soak+Wash+Heavy Wash+Rinse Wash+Heavy Wash Rinse Wash Rinse Spin

Cycle +Rinse+Spin Duty+Rinse+Spin +Spin Duty+Rinse+Spin +Rinse +Spin Only Only Only

COLORS X X X X X X X X X

WHITES X X X X X X X X X

DELICATES X X X X X X X X X

SPEED X X X X X X X X X

WASH

CUSTOM

X X X X X XXXX

CYCLE

ULTRA

X

CLEAN

5

6

About the control and indicator settings.

LOAD SIZE

The water level should just cover the clothes. Adjust the load size accordingly. Loosely load

clothes no higher than the top row of holes in the washer basket.

WASH CYCLE

These wash cycles control the length of the washing process. The chart below will help match the

WASH CYCLE setting to your specific laundry needs. When a cycle is selected, the automatic

temperature that the machine defaults to can be changed to whatever temperature you desire.

Default Wash/Rinse Temperatures

COLORS For easy care and wrinkle-resistant items. WARM / COLD

WHITES For heavy to lightly soiled cotton, household HOT / COLD

linens, towels, work and play clothes.

DELICATES For lingerie and delicate fabrics with COLD / COLD

light to normal soils.

SPEED For one or two lightly soiled items WARM / COLD

WASH that are needed quickly.

CUSTOM Manually selected options of water WARM / COLD

temperature, load size, and wash

options saved for future uses.

ULTRA Maximizes detergent efficiency by adding WARM / COLD

CLEAN water in steps and slowly diluting the

detergent to the standard level.

TEMP WASH/RINSE

Select the water temperature for the wash and rinse cycles. Always follow fabric manufacturer’s

care label or instructions when laundering.

NOTE FOR PORTABLE MODELS: When using a one-faucet connection, adjust the water flow mix

and water temperature at the faucet.

START/PAUSE

Press the START/PAUSE button to start the wash cycle.

EST. MINUTES REMAINING

Displays the time remaining in the wash cycle. It will also display Status Indicators.

See Troubleshooting Tips.

NOTE: When the cycle is complete the control panel will turn off automatically.

3

4

5

6

7

Consumer Support

Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

Installation

Instructions

Safety Instructions

Operating Instructions

7

Consumer Support

Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

Loading and using the washer.

Always follow fabric manufacturer’s care label when laundering. ge.com

Sorting Wash Loads

Loading the Washer

Load dry items loosely, no higher than the top row of

holes in the washer tub. When loading wet items

make sure you set the load/water level high enough

to allow the items to move freely. Water level should

just cover the clothes. To add items after washer has

started, open the lid and add the additional items.

Close the lid. Washer will start automatically.

■ Do not wash fabrics containing flammable

materials (waxes, cleaning fluids, etc.).

■ When the lid is up, a signal will sound and “Lo” will

appear in the display. The washer will not agitate

with the lid up.

Colors

Whites

Lights

Darks

Soil

Heavy

Normal

Light

Fabric

Delicates

Easy Care

Sturdy Cottons

Lint

Lint Producers

Lint Collectors

Care and Cleaning of the Washer

Wash Basket: Leave the lid open after washing to

allow moisture to evaporate. If you want to clean

the basket use a clean, soft cloth dampened with

liquid detergent, then rinse. (Do not use harsh

or gritty cleaners.)

Fill Hoses: Hoses connecting washer to faucet should

be replaced every 5 years.

Exterior: Immediately wipe off any spills. Wipe with

damp cloth. Try not to hit surface with sharp objects.

Moving and Storage: Ask the service technician to

remove water from drain pump and hoses. Do not

store the washer where it will be exposed to the

weather.

Long Vacations: Be sure water supply is shut off at

faucets. Drain all water from hoses if weather will

be below freezing.

Proper Use of Detergent

Add detergent and fabric softener before adding

clothes so that the detergent can work effectively.

Using too little or too much detergent is a common

cause of laundry problems.

Use less detergent if you have soft water, a smaller

load or a lightly soiled load.

GE recommends the use of High Efficiency

detergents. HE detergents are formulated

to work with low water wash and rinse systems.

HE detergents reduce the oversudsing problems

commonly associated with regular detergents.

Loading and using the washer.

8

Fabric Care Labels

Machine

wash

cycle

Normal

Permanent Press/

wrinkle resistant

Gentle/

delicate

Hand wash

Do not wash Do not wring

Water

temperature

Hot

(50°C/120°F)

Warm

(40°C/105°F)

Cold/cool

(30°C/85°F)

Tumble

dry

Dry

Normal

Permanent Press/

wrinkle resistant

Gentle/

delicate

Do not tumble dry

Do not dry

(used with

do not wash)

Heat

setting

High

Medium

Low

No heat/air

Special

instructions

Line dry/

hang to dry

Drip dry

Dry flat

In the shade

WASH LABELS

DRY LABELS

Below are fabric care label “symbols” that affect the clothing you will be laundering.

Consumer Support Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

Installation

Instructions

Safety Instructions

Operating Instructions

9

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT – Save these instructions

for local inspector’s use.

•

IMPORTANT – Observe all governing

codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions

for future reference.

• Skill level – Installation of this appliance requires

basic mechanical skills.

• Completion time – 1 hour

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not

covered under the Warranty.

• Note

–

This appliance must be properly grounded,

and electrical service to the washer must conform

with local codes and ordinances and the latest

edition of the National Electrical Code, ANSI/NFPA 70.

Washer must be installed on firm flooring to minimize

vibration during spin cycles. Concrete flooring is best,

but wood base is sufficient providing floor support

meets FHA standards. Washer should not be installed

on rugs or exposed to the weather.

Install or store where it will not be exposed to

temperatures below freezing or exposed to the weather.

WASHER LOCATION

Installation

Washers

Instructions

WSLP1500 and WSLS1500

• WATER PRESSURE—Must be 10 p.s.i. minimum to 150

p.s.i. maximum dynamic pressure measured at faucet.

• WATER TEMPERATURE—Household water

heater should be set to deliver water at 120° to 150°F

(50° to 66°C) IN THE WASHER when HOT wash is

selected.

• SHUT-OFF VALVES—Both hot and cold shut-off valves

(faucets) should be supplied.

• DRAIN—Water may be drained into a standpipe or set

tub. The discharge height MUST NOT BE LESS THAN

30" nor more than 8' above the base of the washer.

The standpipe must be 1

1

⁄2" minimum inside diameter

and must be open to the atmosphere.

PLUMBING

• Ensure washer is centered between the rack sides.

RACK INSTALLATION

This appliance must be supplied with the voltage and

frequency indicated on the rating plate (located on

the back of the washer) and connected to an individual,

properly grounded branch circuit, protected by a 15- or

20-amp circuit breaker or time-delay fuse.

If the washer is plugged into the dryer’s 115-volt outlet,

then the dryer needs to be on a dedicated circuit.

ELECTRICAL

Pliers

TOOLS REQUIRED

Water Hoses (2)

PARTS SUPPLIED

Drain Hose

Rubber Washers (4)

If you have any questions, call 800.GE.CARES (800.432.2737) or visit our Website at: ge.com

In Canada, call 1.800.561.3344

or visit GEAppliances.ca

10

CAUTION: For personal safety, do

not use an extension cord or adapter plug with this

appliance.

Do not, under any circumstances, cut or remove the

third grounding prong from the power cord. Follow

National Electrical Codes or prevailing local codes

and ordinances.

This appliance must be supplied with the voltage and

frequency indicated on the rating plate (located on the

back of the washer) and connected to an individual,

properly grounded branch circuit, protected by a

15- or 20-amp circuit breaker or time-delay fuse.

If the electric supply provided does not meet the above

requirements, call a licensed electrician.

ELECTRICAL REQUIREMENTS

Installation Instructions

This appliance must be grounded. In the event of a

malfunction or breakdown, grounding will reduce

the risk of electric shock by providing a path of least

resistance for electrical current.

This appliance is equipped with a cord having an

equipment grounding conductor and a grounding plug.

The plug must be plugged into an appropriate outlet that

is properly installed and grounded in accordance with all

local codes and ordinances.

DANGER: Improper connection of the

equipment-grounding conductor can result in a risk of

electrical shock. Check with a qualified electrician if you

are in doubt as to whether the appliance is properly

grounded.

Do not modify plug with this appliance; if it will not fit

the outlet installed, have a proper outlet installed by

a qualified electrician.

Insure proper ground

exists before use

CAUTION: Before plugging in washer, read the following electrical requirements.

GROUNDING INSTRUCTIONS

Before connecting the hoses, the washer must be level.

Leveling locks are located at the bottom front of the left

and right sides of the washer.

LEVELING THE WASHER—

STATIONARY MODELS

MAKE SURE THE WASHER IS IN ITS

FINAL LOCATION

1

PULL OUT THE LEVELING LOCKS

2

This releases the spring loaded leveling feet.

The washer will automatically level itself.

PUSH THE LEVELING LOCKS BACK IN

3

Do not kick or step on the leveling locks.

11

Cable Tie

Laundry Tub

Stand Pipe

WARNING

:Make sure the washer is unplugged.

Run some water from the hot and cold faucets to flush

the water lines and remove particles that might clog up

the water valve screens.

FLUSH WATER LINES

1

Installation Instructions

WASHER CONNECTIONS FOR STATIONARY MODEL WSLS1500

Connect the inlet hose ends to the HOT and COLD water

faucets tightly by hand, then tighten another

2

⁄3 turn with

pliers. Turn the water on and check for leaks.

CONNECT TO WATER LINES

2

CAREFULLY MOVE THE WASHER TO

ITS FINAL LOCATION

3

Form a U shape on the end of the drain hose with

the hose pointed toward the drain. Place the hose in

a laundry tub or stand pipe and secure it with a cable

tie (not included).

NOTE: If the drain hose is placed in a stand pipe without

forming a U shape, a siphoning action could occur. There

must be an air gap around the drain hose. A snug hose

fit can also cause a siphoning action.

CONNECT DRAIN HOSE

4

PLUG THE POWER CORD INTO A

GROUNDED OUTLET

5

Insure proper ground

exists before use

ALCOVE OR CLOSET INSTALLATION

12

60 sq. in.

(387.1 sq. cm)

60 sq. in.

(387.1 sq. cm)

Closet door

Installation Instructions

WASHER CONNECTIONS FOR STATIONARY MODEL WSLS1500

RUN THE WASHER THROUGH A

COMPLETE CYCLE

7

Check for water leaks and proper operation.

REMOVE THE PROTECTIVE FILM

COVERING THE CONTROL PANEL

8

It contains valuable and helpful information that will save

you time and money.

READ THE REST OF THIS OWNER’S

MANUAL

9

NOTE: If your washer does not operate, please review

the Before You Call For Service section.

If your washer is approved for installation in an alcove or

closet, there will be a label on the back of the machine

describing requirements.

• Minimum clearances between washer and adjacent

walls or other surfaces are: 0" either side, 2" front,

3" rear.

• Minimum vertical space from floor to overhead

shelves, cabinets, ceilings, etc. is 96".

• Closet doors must be louvered or otherwise ventilated

and have at least 60 square inches open area for

washer only, or if the closet contains both a washer

and dryer, doors must contain at least 120 square

inches of open area equally distributed.

NOTE: The clearances stated on this label are minimums.

Consideration must be given to providing adequate

clearances for installation and servicing.

INSTALLATION CHECKLIST

6

Before starting the washer, check to make sure:

❏ Main power is turned on.

❏ The washer is plugged in.

❏ The water faucets are turned on.

❏ The unit is level.

❏ The drain hose is properly tied up.

❏ There are no leaks at the faucet, drain line

or washer.

13

Hose Connector

Locking Collar

Uni-Coupler Hose

Faucet Connector

Drain Connection

COLD Water

Supply Connector

Water Filter

Installation Instructions

WASHER CONNECTIONS FOR PORTABLE MODEL WSLP1500—

ONE-FAUCET CONNECTIONS

REMOVE THE UNI-COUPLE

®

HOSE

FROM INSIDE THE WASHER BASKET

1

CONNECT TO WATER LINE

2

Use the hose connector provided with the washer for a

one-faucet connection.

TO CONNECT THE WASHER:

Attach the hose connector to the faucet adapter by

pulling down on the locking collar while lifting up on

the connector until it snaps into place. Make sure the

water filter provided is in place.

CONNECT TO VALVE INLET

3

Attach the COLD water supply connector to the COLD

water valve inlet (color BLUE). Make sure the washer is

inside the connector before tightening.

TIGHTEN CONNECTOR

4

Tighten the connector, ensuring the threads are

aligned properly for tightest fit. Inspect for kinks

or binding of the hose.

NOTE: Do not remove the plastic cap from the HOT

water inlet for uni-coupler connections as leakage may

occur.

Plastic Cap

CONNECT DRAIN HOSE

5

Attach the drain hose to the rear of the washer. Install

the clamp on the drain hose and tighten to prevent

leakage of water.

14

Installation Instructions

WASHER CONNECTIONS FOR PORTABLE MODEL WSLP1500—

ONE-FAUCET CONNECTIONS (CONT.)

MAKE SURE THE TEMPERATURE

SELECTOR IS SET AT COLD/COLD

6

SLOWLY TURN ON THE WATER

FAUCET ALL THE WAY TO THE

DESIRED TEMPERATURE SETTING

7

PLUG THE POWER CORD INTO A

3-PRONG GROUNDED OUTLET

8

Insure proper ground

exists before use

The electrical power cord is on the back of the washer.

REMOVE THE PROTECTIVE FILM

COVERING THE CONTROL PANEL

9

INSTALLATION CHECKLIST

10

Before starting the washer, check to make sure:

❏ Main power is turned on.

❏ The washer is plugged in.

❏ The water faucets are turned on.

❏ The unit is level.

❏ There are no leaks at the faucet, drain line

or washer.

TO DISCONNECT THE WASHER:

15

Hose Connector

Water Flow

Button

TURN WATER FAUCET OFF

1

UNPLUG POWER CORD AND RETURN

IT TO THE STORAGE AREA

2

PRESS THE RED WATER FLOW

BUTTON TO RELEASE THE WATER

PRESSURE

3

DISCONNECT FROM WATER LINE

4

Installation Instructions

Hose Connector

Locking Collar

Move the locking collar down and pull the hose

connector down to disengage from the faucet

adapter.

DRAIN WATER

5

Drain water from the hoses through the

hose connector.

16

TO DISCONNECT THE WASHER:

TO CONNECT THE WASHER:

If you have two separate water connections, your washer

can be connected to both the hot and cold water faucets.

This kit can be purchased from your dealer or from Parts

and Accessories. In the United States, call 800.626.2002.

In Canada, consult the yellow pages for your local Camco

number.

WASHER CONNECTIONS FOR PORTABLE MODEL WSLP1500—

TWO-FAUCET CONNECTIONS

CONNECT TO WATER LINE

1

Connect HOT and COLD water inlet hoses to the HOT

and COLD faucets.

Cable

Tie

Cable

Tie

Sink

Stand Pipe

Secure the drain hose to the sink or stand pipe.

CONNECT DRAIN HOSE

2

PLUG THE POWER CORD INTO A

3-PRONG GROUNDED OUTLET

3

Insure proper ground

exists before use

TURN WATER FAUCETS OFF

1

UNPLUG POWER CORD AND RETURN

IT TO THE STORAGE AREA

2

DISCONNECT THE DRAIN AND WATER

SUPPLY HOSES

3

Hang them on the storage rack.

Installation Instructions

INSTALLATION CHECKLIST

4

Before starting the washer, check to make sure:

❏ Main power is turned on.

❏ The washer is plugged in.

❏ The water faucets are turned on.

❏ The unit is level.

❏ The drain hose is properly tied up.

❏ There are no leaks at the faucet, drain line

or washer.

17

Consumer SupportTroubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

Before you call for service… ge.com

Troubleshooting Tips

Save time and money! Review the charts on the following

pages first and you may not need to call for service.

FF

■ Indicates washer failed to fill. Ensure wall faucets are on and fill hose is

not clogged or kinked.

dr

■ Indicates water has not drained from washer. Ensure the drain hose is

not kinked or connected improperly.

Ub

■ Indicates the laundry load is unbalanced. Reposition laundry evenly in

basket, and ensure washer is level.

Lo

■ Indicates the lid is open. Close the lid.

Status Indicators

LE

■ Indicates washer has leakage. Check the drain hose connection.

IE

■ Press POWER ON/OFF and call service.

OE

■ Indicates water has overflowed. Restart after spinning.

18

Consumer Support Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

Troubleshooting Tips

Installation

Instructions

Safety Instructions

Operating Instructions

Troubleshooting Tips

Installation

Instructions

Safety Instructions

Operating Instructions

Before you call for service…

Troubleshooting Tips

WATER POSSIBLE CAUSES WHAT TO DO

Too many suds Type of detergent • Switch to HE detergent.

Very soft water • Try less detergent.

Too much detergent • Measure your detergent carefully. Use less soap if you

have soft water, a smaller load or a lightly soiled load.

Water leaks Fill hoses or drain hose is • Make sure hose connections are tight at faucets and the

improperly connected washing machine. Make sure the end of the drain

hose

is correctly inserted and secured to the drain.

Household drain may • Check household plumbing. You may need to call

be clogged a plumber.

Constant water pressure • Tighten hoses at the faucets and turn the water off

to the fill hoses at the after each use.

water source

• Check condition of the fill hoses; they may need

replacement after 5 years.

Using too much detergent • Use less detergent. Use less soap if you have soft water,

in washer a smaller load or a lightly soiled load.

Water temperature Water supply is turned off • Turn both hot and cold faucets fully on and make sure

is incorrect or improperly connected hoses are connected to correct faucets.

Water valve screens are •

Turn off the water source and remove the water

stopped up

connection hoses from the upper back of the washer.

Remove screens and use a brush or toothpick to clean the

screens in the machine. Reinstall screens, reconnect the

hoses and turn the water back on.

House water heater is • Make sure house water heater is delivering water

not set properly at 120°F–140°F (48°C–60°C).

Water won’t drain Drain hose is kinked or • Straighten drain hose and make sure washer is not

improperly connected sitting on it.

• Top of drain outlet should be less than 8 ft. above floor.

19

Consumer SupportTroubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

ge.com

OPERATION POSSIBLE CAUSES WHAT TO DO

Washer pauses in cycle

The washer normally pauses

between washing steps

Washer won’t operate Washer is unplugged • Make sure cord is plugged securely into a working outlet.

Water supply is turned off • Turn both hot and cold faucets fully on.

Controls are not set properly • Make sure all selections have been made.

Lid is open • Close lid and press START/PAUSE.

Circuit breaker/fuse is • Check house circuit breakers/fuses. Replace fuses or

tripped/blown reset breaker. Washer should have separate outlet.

Washer has not been • Press the POWER ON/OFF button.

turned on

PERFORMANCE POSSIBLE CAUSES WHAT TO DO

Colored spots Incorrect use of fabric • Check fabric softener package for instructions and

softener follow directions for using dispenser.

• Pretreat stain and rewash.

Dye transfer • Sort whites or lightly colored items from dark colors.

Grayed or yellowed Not enough detergent • Use more detergent (especially with larger loads).

clothes

Hard water • Use a water conditioner like Calgon brand or install

a water softener.

Water is not hot enough • Make sure water heater is delivering water at

120°F–140°F (48°C–60°C).

Washer is overloaded • Select load size to match clothes load.

Dye transfer • Sort clothes by color. If fabric label states wash separately,

unstable dyes may be indicated.

Lint or residue on Clothes are air or line dried • If you do not dry your clothes with a clothes dryer,

clothes your clothes may retain more lint.

Incorrect sorting • Separate lint producers from lint collectors.

Washing too long • Wash small loads for a shorter time than larger loads.

Overloading • Load clothes no higher than the top row of holes in the

washer tub.

• Make sure load size selector matches clothes load size.

Incorrect use of fabric softener • Check fabric softener package for instructions and

follow directions for using dispenser.

Pilling Result of normal wear on • While this is not caused by the washer, you can slow the

poly-cotton blends and pilling process by washing garments inside out.

fuzzy fabrics

20

Consumer Support Troubleshooting Tips

Operating Instructions

Safety Instructions

Installation

Instructions

Troubleshooting Tips

Installation

Instructions

Troubleshooting Tips

Installation

Instructions

Before you call for service…

PERFORMANCE (cont.) POSSIBLE CAUSES WHAT TO DO

Snags, holes, tears, rips Pins, snaps, hooks, sharp • Fasten snaps, hooks, buttons and zippers.

or excessive wear buttons, belt buckles,

• Remove loose items like pins, objects in pockets

zippers, and sharp objects

and sharp buttons.

left in pockets

• Turn knits (which snag easily) inside out.

Undiluted chlorine bleach • Check bleach package instructions for proper amount.

• Never add undiluted bleach to wash or allow clothes

to come in contact with undiluted bleach.

Chemicals like hair bleach • Rinse items that may have chemicals on them before

or dye, permanent wave washing.

solution

Wrinkling Improper sorting • Avoid mixing heavy items (like work clothes) with

light items (like blouses).

• Try a fabric softener.

Overloading or • Load your washer so clothes have enough room

incorrect water level to move freely.

Repeated washing in • Wash in warm or cold water.

water that is too hot

NOISE POSSIBLE CAUSES WHAT TO DO

Washer is noisy Washer is uneven • Level the washer. See Leveling the Washer.

Washer load is

• Press the

START/PAUSE

button to stop the washer, open

unbalanced the lid and redistribute the load evenly. Close the lid

and restart.

Washer is sitting too close • Pull washer away from the wall; about 4" is needed.

to wall (causes knocking

during cycle)

Dragging noise prior When using the LOAD • This is normal.

to water filling in SENSING feature, the

the tub agitator rotates before

water fills in the tub

OTHER POSSIBLE CAUSES WHAT TO DO

Labels on the exterior Occasionally the adhesive • Use a hair dryer set at the lowest heat setting, directing

of the washer will not used on the labels does the air at the label for a short amount of time. This will

peel off cleanly not release cleanly release the adhesive easily, without damaging the surface

of the washer.

Troubleshooting Tips

La page charge ...

GE Appliances WSLS1500 Manuel utilisateur

GE Appliances WSLS1500 Manuel utilisateur

dans d''autres langues

Autres documents