18
On newly purchased machines this function is active (the " "
light (16) is on) and is performed at the end of the warm-up
phase, when the " " light (14) turns on steady.
Note: should no water pour from the lter
holder, perform a manual rinse as described in
sect. 7.1.
The rinsing procedure may:
A be stopped by pressing the " " (15) or (13) button.
B be deactivated by pressing the " "
button (15) while
the
" "
light (14) is blinking or steady on
; in this case the
" " light (16) turns o.
Note: if the rinsing procedure is deactivated, it
can be reactivated only by pressing the " "
button.
6 Energy Saving
The machine is designed for energy saving.
After 9 minutes of inactivity, the machine turns o in order to
save energy and respect nature.
Press the ON/OFF " " button (11) to operate the machine.
7 Coee Brewing
Warning! During coee brewing it is forbidden
to remove the pressurized lter holder by
manually turning it from right to left. Danger of burns!
• During this operation, the " " light (14) is blinking; this
is to be considered as a standard and not a faulty operating
mode.
• Before using the machine, make sure that there is enough
water in the machine tank.
Note: if the steam knob is opened by mistake
during the warm-up phase, the " " light
(20) starts blinking. Close the knob and wait until the
machine is ready.
If coee is NOT brewed after pressing the brew
button " " (13), press the brew button " "
(13) again and check the "Troubleshooting" table before
removing the lter holder.
Ensure the machine is ready before brewing coee. The
machine is ready when the " " light (14) is steady on.
7.1 Filter Holder Warm-Up
If the "rinse" function is not activated and/or the lter holder is
to be warmed-up manually, do as follows:
•
13
Insert the pressurized lter holder into the brew unit
(4) from the bottom.
•
14
Turn the pressurized lter holder from left to right un-
til it locks into place. Release the pressurized lter holder
grip. The handle will turn slightly to the left. This move-
ment guarantees optimum lter holder performance.
•
17
Preheat the pressurized lter holder by pressing the
(13) button; some water will ow out of the pressurized
lter holder (this operation is necessary only for the rst
coee).
• After 50cc of water have been dispensed, press the (13)
button again to stop the dispensing procedure.
•
19
Remove the pressurized lter holder by turning it from
right to left and then drain the remaining water.
Place a container under the dispensing spout.
Now you can go on with the coee brewing procedures
described in the following sections.
7.2 Using Ground Coee
•
7
Insert the lter (23) in the pressurized lter holder
(21); at rst use, the lter is already on. With the special
lter (23) provided there is no need to change the lter to
make one or two coee(s).
•
8
Add 1-1.5 measuring scoop(s) for a single coee and 2
measuring scoops for a double coee. Remove any coee
residues from the rim of the pressurized lter holder.
Note: do not press the coee, since the lter
holder is provided with an optimized system
for original espresso brewing.
•
13
Insert the lter holder (21) into the brew unit (4) from
the bottom.
•
14
Turn the pressurized lter holder from left to right un-
til it locks into place. Release the pressurized lter holder
grip. The handle will turn slightly to the left. This move-
ment guarantees optimum lter holder performance.
•
16
Take 1 or 2 preheated cups and place them un-
der the pressurized lter holder. Make sure that they are
placed correctly under the coee brewing nozzles.
•
17
Press the " " button (13).
•
18
When the desired quantity of coee has been brewed,
press the " " button (13) again to stop the brewing pro-
cedure. Wait for a few seconds after brewing, then remove
the cups of coee.
4219-450-03851 MANUAL GAG. V2 RI8525 GGBF US 1-3L V2.indd 18 03/09/2020 10:16:37