Sauder 422357 Manuel utilisateur

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.

Prefer the phone? Call 1-800-523-3987.

Share your journey!

sauder.com

NOTE: THIS INSTRUCTION

BOOKLET CONTAINS IMPORTANT

SAFETY INFORMATION.

PLEASE READ AND KEEP FOR

FUTURE REFERENCE.

English pg 1-27

Français pg 28-31

Español pg 32-36

Lot # 510604 11/09/17

Purchased: __________________

Be sure to give us a ring before

making any returns. 1-800-523-3987

Welcome to the

big kid desk.

Sit/Stand Desk

Model 422357

Table of Contents Assembly Tools Required

Part Identiﬁ cation

Hardware Identiﬁ cation

Assembly Steps

Français

Español

Safety

Warranty

Hammer

Not actual size

No. 2 Phillips Screwdriver

Tip Shown Actual Size

3

3-5

6-27

28-31

32-36

37- 38

39

Skip the power trip.

This time.

Short Screwdriver

422357 www.sauder.com/servicesPage 2

Adjustable Wrench

å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge

to help distinguish similar parts from each other. Use this part identiﬁ cation to help identify similar parts.

Now you know

our ABCs.

Part Identiﬁ cation

A RIGHT END (1)

B LEFT END (1)

C MODESTY PANEL (1)

D SHELF (1)

E2 UPRIGHT (1)

F2 LIFT TOP BACK (1)

G LIFT TOP LEFT END (1)

H LIFT TOP RIGHT END (1)

I LIFT TOP (1)

A

B

C

D

E2

F2

G

H

I

Hardware Identiﬁ cation

(EXTENSION SET SHOWN SEPARATED)

EXTENSION RAIL - 2

J

EXTENSION SLIDE - 2

K

7F

TWIST-LOCK

®

FASTENER - 21

ROD - 1

26A

422357www.sauder.com/services

Page 3

16E

LEVELER - 4

Hardware Identiﬁ cation

å Screws are shown actual size. You may receive extra hardware with your unit.

COTTER PIN - 2

19M

RACK TENSIONER - 2

121M

ACTUATOR PULL - 1

120M

WHEEL - 2

123M

LEFT AND RIGHT RACK

DRIVE SET - 1

122M

CYLINDER - 1

124M

PROPEL NUT - 4

14M

GROMMET CAP - 1

1P

61P

TWIST-LOCK

®

FASTENER COVER - 12

62P

MINI TWIST-LOCK

®

COVER - 1

65P

CORD

MANAGER - 2

SCREW COVER - 4

20P

METAL PIN - 2

1R

CORD CLIP - 2

9P

GROMMET - 3

10P

32G

LEVELER

BRACKET - 4

CABLE BRACKET - 1

72G

CYLINDER BRACKET - 2

71G

13F

MINI TWIST-LOCK

®

FASTENER - 1

422357 www.sauder.com/servicesPage 4

NUT - 4

24M

WASHER - 4

13M

Hardware Identiﬁ cation

å Screws are shown actual size. You may receive extra hardware with your unit.

BLACK 9/16" PAN HEAD SCREW -14

51S

BLACK 9/16" LARGE HEAD SCREW - 12

1S

BROWN 7/16" LARGE HEAD SCREW - 2

6S

BROWN 1-1/2" FLAT HEAD SCREW - 6

14S

SILVER 5/8" FLAT HEAD SCREW - 20

23S

BLACK 1-15/16" FLAT HEAD SCREW - 5

113S

422357www.sauder.com/services

Page 5

BLACK 1-1/4" MACHINE SCREW - 4

93S

Step 1

Look for this icon. It means a

video assembly tip is available at

www.sauder.com/services/tips

å

Assemble your unit on a carpeted ﬂ oor or on the empty

carton to avoid scratching your unit or the ﬂ oor.

å

To begin assembly, push a SAUDER TWIST-LOCK®

FASTENER (7F) into the large holes in the MODESTY

PANEL (C), SHELF (D), UPRIGHT (E2), and LIFT

TOP ENDS (G and H).

422357 www.sauder.com/servicesPage 6

G

H

Do not tighten the TWIST-LOCK® FASTENERS in this step.

(21 used)

7F

D

E2

C

Scan this QR code or go to this address:

http://qr.sauder.com/?ID=1933

to watch a video on how to assemble your unit.

å

Fasten the LEFT RACK DRIVE to the LIFT TOP LEFT END (G) and

the RIGHT RACK DRIVE to the LIFT TOP RIGHT END (H). Use

fourteen BLACK 9/16" PAN HEAD SCREWS (51S).

å

NOTE: Be sure to use the exact holes with dashed lines.

Step 2

G

H

The LEFT RACK

DRIVE will have an

L stamped here.

The RIGHT RACK

DRIVE will have an

R stamped here.

BLACK 9/16" PAN HEAD SCREW

(14 used in this step)

51S

422357www.sauder.com/services

Page 7

These edges must be even.

Step 3

å

Push a SAUDER MINI TWIST-LOCK® FASTENER (13F) into

the hole in the LIFT TOP BACK (F2).

Do not tighten the MINI TWIST-LOCK® FASTENER in this step.

13F

F2

422357 www.sauder.com/servicesPage 8

å

Fasten the LIFT TOP BACK (F2) to the LIFT TOP (I).

Tighten the MINI TWIST-LOCK® FASTENER.

Step 4

How to use the SAUDER TWIST-LOCK® FASTENER

and MINI TWISTLOCK® FASTENER

1. Insert the dowel end of the FASTENER into the

hole of the adjoining part.

NOTE: The dowel end of the FASTENER must

remain fully inserted in the hole of the adjoining

part while locking the FASTENER.

2. Tighten the FASTENER with a Phillips

screwdriver as tight as possible.

F2

I

This large hole

must be here.

Surface with MINI TWIST-LOCK® FASTENER

Surface with holes

422357www.sauder.com/services

Page 9

Remember:

Righty tighty.

Lefty loosey.

Meet Part (I). This component has

been engineered to be lighter, stronger,

faster… well ok. Not technically faster.

But deﬁ nitely makes for a sturdier Sit/

Stand Desk that’s easier to assemble

and friendlier to the environment.

å

Fasten the LIFT TOP ENDS (G and H) to the LIFT TOP BACK (F2).

Use six BROWN 1-1/2" FLAT HEAD SCREWS (14S).

å

Fasten the LIFT TOP ENDS (G and H) to the LIFT TOP (I). Tighten

six TWIST-LOCK® FASTENERS.

Step 5

H

G

BROWN 1-1/2" FLAT HEAD SCREW

(6 used in this step)

14S

I

F2

422357 www.sauder.com/servicesPage 10

Surface with TWIST-LOCK® FASTENERS

å

Separate the EXTENSION SLIDES (K) from the EXTENSION RAILS (J) as shown

in the upper diagram below. Be prepared, the parts are greasy.

å

Fasten the EXTENSION SLIDES (K) to the LIFT TOP ENDS (G and H). Use ten

SILVER 5/8" FLAT HEAD SCREWS (23S).

å

Fasten the CABLE BRACKET (72G) to the LIFT TOP (I). Use two BLACK 9/16"

LARGE HEAD SCREWS (1S).

Step 6

H

G

Open end

BLACK 9/16" LARGE HEAD SCREW

(2 used in this step)

1S

SILVER 5/8" FLAT HEAD SCREW

(10 used for the EXTENSION SLIDES)

23S

I

422357www.sauder.com/services

Page 11

Pull down the release lever and pull the SLIDE from the RAIL.

J

K

72G

K

å

Fasten two CORD MANAGERS (65P) to the LIFT TOP BACK (F2). Use

two BROWN 7/16" LARGE HEAD SCREWS (6S).

å

Fasten a CYLINDER BRACKET (71G) to the LIFT TOP BACK (F2). Use

two BLACK 1-1/4" MACHINE SCREWS (93S), two WASHERS (13M),

and two NUTS (24M).

å

NOTE: Position the CORD MANAGERS and CYLINDER BRACKET

exactly as shown.

Step 7

65P

F2

422357 www.sauder.com/servicesPage 12

71G

BLACK 1-1/4" MACHINE SCREW

(2 used in this step)

93S

24M

13M

BROWN 7/16" LARGE HEAD SCREW

(2 used in this step)

6S

å

Fasten the SHELF (D) to the MODESTY PANEL (C).

Tighten three TWIST-LOCK® FASTENERS.

å

Push two GROMMETS (10P) into the SHELF (D).

Step 8

Surface with

TWIST-LOCK®

FASTENERS

Surface with TWIST-LOCK® FASTENERS

C

D

10P

422357www.sauder.com/services

Page 13

å

Fasten a CYLINDER BRACKET (71G) to the UPRIGHT (E2).

Use two BLACK 1-1/4" MACHINE SCREWS (93S), two

WASHERS (13M), and two NUTS (24M).

Step 9

Surface with TWIST-LOCK® FASTENERS

This hole must be here.

The post on the

BRACKET must be

pointing this direction.

E2

422357 www.sauder.com/servicesPage 14

71G

24M

13M

BLACK 1-1/4" MACHINE SCREW

(2 used in this step)

93S

å

Fasten the UPRIGHT (E2) to the SHELF (D). Use ﬁ ve

BLACK 1-15/16" FLAT HEAD SCREWS (113S).

å

Push two CORD CLIPS (9P) into the MODESTY PANEL (C).

Step 10

E2

D

BLACK 1-15/16" FLAT HEAD SCREW

(5 used in this step)

113S

9P

C

422357www.sauder.com/services

Page 15

Now might be a

good time to refresh

your drink.

Surface without TWIST-LOCK®

FASTENERS

Step 11

å

Fasten the EXTENSION RAILS (J) to the ENDS (A and B). Use ten SILVER 5/8" FLAT HEAD SCREWS (23S).

å

NOTE: For each EXTENSION RAIL, turn a SCREW into the holes shown in the enlarged diagram. Then, slide

the inner cartridge of the EXTENSION RAIL in to ﬁ nd the other holes that lines up with the hole in the END.

Turn a SCREW into these holes.

å

Insert a METAL PIN (1R) into each END (A and B) as shown.

Open end

1R

A

B

J

These four small

holes must be here.

422357 www.sauder.com/servicesPage 16

SILVER 5/8" FLAT HEAD SCREW

(10 used in this step)

23S

These four small

holes must be here.

å

NOTE: You will need a short screwdriver in this step.

å

Fasten the ENDS (A and B) to the MODESTY PANEL (C),

SHELF (D), and UPRIGHT (E2). Tighten twelve

TWIST-LOCK® FASTENERS.

å

NOTE: Be sure the METAL PIN in each END inserts into

the UPRIGHT (E2).

Step 12

A

B

C

D

E2

422357www.sauder.com/services

Page 17

å

Push four LEVELER BRACKETS (32G) over the exact holes shown in the bottom edges of the ENDS (A and B).

å

Using your hammer, gently tap a PROPEL NUT (14M) into the holes in the LEVELER BRACKETS (32G) and

ENDS (A and B). Now, turn a LEVELER (16E) into each PROPEL NUT.

å

NOTE: Position the BRACKETS exactly as shown.

Step 13

Use these holes in the second unit if

you will be standing them side by side.

422357 www.sauder.com/servicesPage 18

A

B

16E

14M

32G

å

Carefully stand your unit upright.

å

Fasten a RACK TENSIONER (121M) to the RIGHT END (A).

Use four BLACK 9/16" LARGE HEAD SCREWS (1S).

å

NOTE: Position the RACK TENSIONER exactly as shown.

Step 14

A

422357www.sauder.com/services

Page 19

BLACK 9/16" LARGE HEAD SCREW

(4 used in this step)

1S

121M

Use the exact

holes shown.

å

Push two WHEELS (123M) onto the ROD (26A)

a few inches in from the end.

Step 15

Flat edge

26A

123M

422357 www.sauder.com/servicesPage 20

Push the WHEEL onto

the ROD a few inches.

Push the WHEEL onto

the ROD a few inches.

La page charge ...

Sauder 422357 Manuel utilisateur

Sauder 422357 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents