Phase Technology CI820 Le manuel du propriétaire

Marque: Phase Technology

Modèle: CI820

Taper: Le manuel du propriétaire

Ce manuel convient également à

CI520
CI620

FLEXIBLE CONDUIT CLAMP

TILE BRIDGE

COVER PLATE

SECONDARY ATTACHMENT

POINT

SPEEDWING

™

MOUNTING

ARMS

INSTALLATION AID/

PAINT MASK

BAFFLE

GRILLE

GRILLE SAFETY RESTRAINT

[BOX CONTENTS]

1 SPEAKER

1 FLEXIBLE CONDUIT CLAMP

1 COVER PLATE

1 GRILLE

1 INSTALLATION AID/ PAINT MASK

MAX: 1.6” MIN: 0.035”

CEILING THICKNESS TOLERANCES

All CI Series speakers include self-resetting solid-state PTC protection circuits. This

unique system is able to detect when the speaker is being over-driven and lowers the

speaker volume until the problem is corrected. The PTC device then resets itself for

normal operation.

Regardless of application, serious audiophile listening or home theater, we recommend

that you take the time to read this manual thoroughly before connecting speakers to your

amplier or receiver. In the highly unlikely event that you should experience a problem

with set-up or operation, please contact one of our authorized dealers for assistance, or

Phase Technology

Corporation

8005 W. 110th St., Suite 208

Overland Park, KS 66210

855.663.5600 (Domestic)

+1.913.663.5600 (International)

913.663.3200 (Fax)

SAFETY INSTRUCTIONS 2

DROPTILE CEILING INSTALL 3

SHEETROCK CEILING INSTALL 4

PRE-CONSTRUCTION BRACKET INSTALL 5

CARING FOR YOUR SPEAKER 5

MAINTENANCE AND SERVICE 6

WARRANTY 6

SPECIFICATIONS 6

CIX IN-CEILING

OWNER’S MANUAL: CI520 • CI620 • CI820

1. Read Instructions - All the safety and operating instructions

should be read before the appliance is operated.

2. Retain Instructions - The safety and operating instructions

should be retained for future reference.

3. Heed Warnings - All warnings on the appliance and in the

operating instructions should be adhered to.

4. Follow Instructions - All operating and other instructions

should be followed.

5. Water and Moisture - The appliance should not be used near

water - for example, near a bathtub, washbowl, kitchen sink,

laundry tub, in a wet basement, or near a swimming pool, etc.

6. Carts and Stands - The appliance should be used only with a

cart or stand that is recommended by the manufacturer.

PORTABLE CART WARNING

7. Wall or Ceiling Mounting - The appliance should be mounted

to a wall or ceiling only as recommended by the manufacturer.

8. Ventilation - The appliance should be situated so that its

location or position does not interfere with its proper ventilation.

For example, the appliance should not be situated on a bed, sofa,

rug, or similar surface that may block the ventilation openings;

or placed in a built-in installation, such as a bookcase or cabinet

[SAFETY INSTRUCTIONS]

that may impede the ow of air through the ventilation openings.

9. Heat - The appliance should be situated away from heat sources

such as radiators, stoves, or other appliances that produce heat.

10. Power Source - The appliance should be connected to

a power supply only of the type described in the operating

instructions or as marked on the appliance.

11. Power Cord Protection - Power supply cords should be

routed so that they are not likely to be walked on or pinched by

items placed up or against them, paying particular attention to

cords at plugs, convenience receptacles, and the point where they

exit from the appliance.

12. Cleaning - The appliance should be cleaned only as

recommended by the manufacturer.

13. Nonuse Periods - The power cord of the appliance should

be unplugged from the outlet when left unused for a long period

of time.

14. Object and Liquid Entry - Care should be taken so that

neither objects fall nor liquids spill into the inside of the appliance.

15. Damage Requiring Service - The application should be

serviced by qualied service personnel when:

a. the power supply cord or the plug has been damaged,

b. objects have fallen onto or liquid has been spilled into the

appliance,

c. the appliance has been exposed to rain,

d. the appliance does not appear to operate normally or exhibits a

marked change in performance, or

e. the appliance has been dropped or the cabinet damaged.

16. Servicing - The user should not attempt to service the

appliance beyond those means described in the operating

instructions. All other servicing should be referred to qualied

service personnel.

17. Grounding or Polarization - Precautions should be taken so

that the grounding or polarization means of an appliance is not

defeated.

Explanation of Graphical Symbols

The lightning ash with arrowhead symbol, within an

equilateral triangle, is intended to alert you to the presence

of un-insulated “dangerous voltage: within the product’s

enclosure that may be off sufcient magnitude to constitute

a risk of electric shock to persons.

The exclamation point within an equilateral triangle is

intended to alert you to the presence of important operating

and maintenance (servicing) instructions in the literature

accompanying the appliance.

APPLICABLE FOR USA, CANADA OR WHERE APPROVED FOR

USAGE

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE

PLUG TO WIDE SLOT, INSERT FULLY.

ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE

LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE

CORRESPONDANTE DE LA PRESE ET POUSSER JUSQU AU FOND.

CAUTION: To reduce the risk of electric shock, do not remove cover

(or back). No user-serviceable parts inside. Refer servicing to qualied

service personnel.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

[DROPTILE CEILING INSTALL INSTRUCTIONS FOR: CI-520, CI-620 & CI-820]

1. Unpack speaker & set aside grille

assembly.

2. Use optional tile bridge to mark

cutout in tile.

3. Use Rotozip or other tool to cut

hole.

Hole Diameter: 10.5”

4. Run signal wires through conduit

connector, then through the cover

plate. Connect to ceramic terminal

strip. Two + and two - connectors

are provided for daisy chaining.

5. Tighten screw on terminal plate,

and push conduit connector into

knockout.

6. Insert speaker into mounting hole

with installation aid in place. Screw

down both bolts on the bafe face to

actuate the mounting wings. Firmly

secure both bolts - DO NOT OVER-

TIGHTEN

7. If required, a sheet metal tab

located on the rear panel of the

speaker serves as a secondary point

of attachment (cable not included).

8. Once all painting and nish work

is completed, remove the paint

mask.

9. Select the tap position by

adjusting rotary switch to desired

high impedance value or transformer

bypass mode.

10. Attach grille safety clip by plac-

ing the large end of the clip over the

snap-t post (1), then sliding clip un-

til small end snaps into place around

post (2).

11. Press grille into place 12. Done!

[SHEETROCK CEILING INSTALL INSTRUCTIONS FOR: CI-520, CI-620 & CI-820]

1. Unpack speaker & set aside grille

assembly.

2. Use optional tile bridge to mark

cutout in tile.

3. Use Rotozip or other tool to cut

hole.

Hole Diameter: 10.5”

4. Run signal wires through conduit

connector, then through the cover

plate. Connect to ceramic terminal

strip. Two + and two - connectors

are provided for daisy chaining.

5. Tighten screw on terminal plate,

and push conduit connector into

knockout.

6. If required, a sheet metal tab

located on the rear panel of the

speaker serves as a secondary point

of attachment (cable not included).

7. Insert speaker into mounting hole

with installation aid in place. Screw

down both bolts on the bafe face to

actuate the mounting wings. Firmly

secure both bolts - DO NOT OVER-

TIGHTEN

8. Once all painting and nish work

is completed, remove the paint

mask.

9. Select the tap position by

adjusting rotary switch to desired

high impedance value or transformer

bypass mode.

10. Attach grille safety clip by plac-

ing the large end of the clip over the

snap-t post (1), then sliding clip un-

til small end snaps into place around

post (2).

11. Press grille into place 12. Done!

[PRE-CONSTRUCTION BRACKET INSTALL INSTRUCTIONS FOR: CI-520, CI-620 & CI-820]

1. Nail or screw optional bracket to

joists. Secure conduit/ signal wire

away from hole in bracket.

2. Complete nish work. 3. Use Rotozip or other tool to cut

hole.

Hole Diameter: 10.5”

4. Run signal wires through conduit

connector, then through the cover

plate. Connect to ceramic terminal

strip. Two + and two - connectors

are provided for daisy chaining.

5. Tighten screw on terminal plate,

and push conduit connector into

knockout.

6. If required, a sheet metal tab

located on the rear panel of the

speaker serves as a secondary point

of attachment (cable not included).

7. Insert speaker into mounting hole

with installation aid in place. Screw

down both bolts on the bafe face to

actuate the mounting wings. Firmly

secure both bolts - DO NOT OVER-

TIGHTEN

8. Once all painting and nish work

is completed, remove the paint

mask.

9. Select the tap position by

adjusting rotary switch to desired

high impedance value or transformer

bypass mode.

10. Attach grille safety clip by plac-

ing the large end of the clip over the

snap-t post (1), then sliding clip un-

til small end snaps into place around

post (2).

11. Press grille into place 12. Done!

[CARING FOR YOUR PHASE TECHNOLOGY SPEAKER]

All Phase Technology

speakers are nished with a high degree of craftsmanship in either hand polished paint or vinyl laminates. We

recommend using a lint-free rag with a small amount of glass cleaner to maintain the long-lasting beauty of the nish. Avoid products

containing silicones, oils, oil derivatives, or solvents. Use a damp cloth on enclosures nished in vinyl laminates.

[MAINTENANCE AND SERVICE]

Because of Phase Technology’s uncompromising quality control programs, it’s unlikely that your speakers will ever need service if

connected and used as outlined in this Owners’ Manual. In the unlikely event that a problem does occur, please contact your Phase

Technology dealer. Your dealer has the necessary factory-authorized parts and trained technicians to quickly restore your speaker to its

original performance specications.

[WARRANTY]

LIMITED WARRANTY: Phase Technology

warrants its loudspeakers to be free from defects in material and workmanship for a period

of ten (10) years for speaker product, limited lifetime for CI speakers, and three (3) years for the electronic components to the original

purchaser. Purchase must be made from an authorized Phase Technology dealer.

This warranty does not cover service or parts to repair damage caused by misuse, abuse, damage while in transit, alterations,

unauthorized repairs, failure to follow instructions, re, ood or any other cause beyond the reasonable control of Phase Technology

Defects in speaker cabinets or grilles must be brought to the attention of your dealer immediately after purchase. This warranty will be

void if the products’ serial number has been altered or removed.

Should your Phase Technology

product require service, please call the MSE Audio

customer service department for a return

authorization. All merchandise returned to Phase Technology

without prior authorization will be refused. For your return authorization

number, please call 855.663.5600 or email sales@mseaudio.com.

5.25” Coax In-Ceiling

16Ω

84.5 dB

65 Hz - 22 kHz

10 - 80 Watts

.75” Soft Dome

N/A

5.25” Polypropylene w/ NBR Surround

Ceramic Terminal Connector

White Steel (paintable)

11.75” Diameter x 5.75” Depth

10.5” Diameter

6.09”

8 lbs

Tile Bridge, UL-Listed Flex Conduit Clamp,

Paint Shield

Pre-Construction Bracket (AC-CI20-PCB),

Tile Bridge (AC-CI20-TB)

6.5” Coax In-Ceiling

16Ω

85 dB

60 Hz - 22 kHz

10 - 80 Watts

.75” Soft Dome

N/A

6.5” Polypropylene w/ NBR Surround

Ceramic Terminal Connector

White Steel (paintable)

11.75” Diameter x 5.75” Depth

10.5” Diameter

6.09”

8 lbs

Tile Bridge, UL-Listed Flex Conduit Clamp,

Paint Shield

Pre-Construction Bracket (AC-CI20-PCB),

Tile Bridge (AC-CI20-TB)

6.5” Coax In-Ceiling

16Ω

86 dB

55 Hz - 22 kHz

10 - 80 Watts

.75” Soft Dome

N/A

8” Polypropylene w/ NBR Surround

Ceramic Terminal Connector

White Steel (paintable)

11.75” Diameter x 8” Depth

10.5” Diameter

8.34”

9 lbs

Tile Bridge, UL-Listed Flex Conduit Clamp,

Paint Shield

Pre-Construction Bracket (AC-CI20-PCB),

Tile Bridge (AC-CI20-TB)

Description:

Nominal Impedance:

Sensitivity:

Frequency Response:

Recommended Power:

Tweeter(s):

Midrange:

Woofer(s):

Inputs:

Grille:

Dimensions:

Cutout Dimensions:

Mounting Depth:

Weight:

Included Accessories:

Optional Accessories:

CI520 CI620 CI820

“Speakers for your Life” is a trademark of MSE Audio, Overland Park, Kansas USA. Phase Technology is part of MSE Audio

. www.phasetech.com.

Phase Technology CI820 Le manuel du propriétaire

Marque: Phase Technology

Modèle: CI820

Taper: Le manuel du propriétaire

Ce manuel convient également à

CI520
CI620

Télécharger le PDF

rapport

dans d''autres langues

English: Phase Technology CI820 Owner's manual

Phase Technology CI820 Le manuel du propriétaire

Ce manuel convient également à

Phase Technology CI820 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents