Philips CID3283/93 Guide de démarrage rapide
- Catégorie
- Récepteurs multimédia de voiture
- Taper
- Guide de démarrage rapide
Ce manuel convient également à
www.philips.com/welcome
Register your product and get support at
CID3283
ENG Quick Start Guide
1
2
3
English
Install the car audio
These instructions are for a typical installation.
However, if your car has different requirements,
make the corresponding adjustment. If you have
any questions regarding installation kits, consult
your Philips car audio dealer.
Caution
This unit is designed for negative ground
(earth) 12 V DC operation only.
Always install this unit in the car dashboard.
Other locations can be dangerous as the rear
of the unit heats up during use.
To avoid short-circuit: before you connect,
ensure that the ignition is off.
Ensure that you connect the yellow and red
power supply leads after all other leads are
connected.
Ensure that all loose leads are insulated with
electrical tape.
Ensure that the leads do not get caught under
screws orin parts that will move (e.g. seat rail).
Ensure that all ground (earth) leads are run to
a common ground (earth) point.
Use only the supplied mounting hardware for
a safe and secure installation.
,PSURSHUIXVHVFDQFDXVHGDPDJHRUÀUH
When you need to change the fuse, consult a
professional.
Note on the power supply lead (yellow)
When you connect other devices to this
system, ensure that the rating of the car
circuit is higher than the total fuse value of all
the connected devices.
Notes on speaker connection
Never connect speaker wires to the metal
body or chassis of the car.
Never connect speaker wires with stripes to
one another.
Turn on
Caution
Risk of road accidents! Never watch video or
adjust settings while you drive.
1 Press to turn on the unit.
The available OSD (On-Screen Display) »
languages are displayed.
2 Touch a language to select.
The OSD language is changed to the »
selected language immediately.
To turn off the unit, press
for 3 seconds.
Set date and time
1
Touch the upper left corner to display main
menu.
2 Touch in the middle right side of the
screen.
The second main menu is displayed.»
2 Touch on [12Hr] or [24Hr] to select clock
mode.
Set time
1 Touch [Time].
2 Touch on the displayed time.
A submenu is displayed.»
3 Touch or to set hour and minute.
Tip
When date/time is set, touch ÀUVWDQGWKHQ
touch
to return to main menu.
Adjust screen
To adjust screen brightness/contrast/color
1 Press DISP/ / .
2 Press or to select an item.
3 Touch / to adjust the value.
4 Press DISP/ / WRFRQÀUP
To turn on/off the screen, press and hold DISP/
/ .
Use map
Note
You may need to upgrade the map before
using it (see “Upgrade the map” section)
3 Touch on FM or AM to select band:
FM band options: FM1, FM2, FM3
AM band options: AM1, AM2
4 %ULHÁ\WRXFK or to tune to a radio
station by step.
Touch
or for over 1 seconds to tune
to a radio station automatically.
Play disc
3
You can play video, audio or images stored on the
following discs:
DVD video, DVD-R, DVD-RW
VCD
Audio CD, CD-R, CD-RW
Note
Ensure that the disc contains playable content.
You can play DVD discs with the following region
codes:
DVD region code Country
China
1 Inser t the disc into the disc slot with label
side facing up.
Play starts automatically. »
To remove the disc, press the »
button.
When the disc is ejected, the unit
»
switches to the previous source,
if connected. Otherwise, the
unit switches to [Radio] mode
automatically.
3 Enter default password “0000”.
if pairing succeeds. phone call record is »
displayed.
Make a call
1 Pair the phone with the unit.
2 Touch the upper left corner to display the
home menu.
3 Touch [Bluetooth].
The Bluetooth menu is displayed.»
4 Touch or to select the paired phone,
then touch
.
5 Touch or to search for phone number
from the following list:
Or touch to dial number directly, then touch
to dial.
4
5
a
b
c
© 2009 Koninklijke Philips Electronics N.V.
All rights reserved.
CID3283_93_QSG_V1.0
Connect wires
1
Caution
Ensure that all loose leads are insulated with
electrical tape.
1 Check the car’s wiring carefully, then do the
other connections:
Mount in the dashboard
2
Note
Check wire connection before you mount the
unit into a car.
If preset radio stations are lost when the
ignition key is turned OFF and then back ON,
reconnect the red leads crosswise to the
yellow ones.
1 If the car does not have an on-board drive or
navigation computer, disconnect the negative
terminal of the car battery.
If you disconnect the car battery in a car
that has an on-board drive or navigation
computer, the computer may lost its
memory.
If the car battery is not disconnected,
to avoid shor t-circuit, ensure that bare
wires do not touch each other.
2 Take out the original car audio and keep the
screws.
3 Mount the plastic screw that is taken off
from the original car audio onto the backside
of the unit.
a
4 Slide the unit into the dashboard until a click
sound is heard.
b
5 Mount on the screws.
c
6 Reconnect the negative terminal of the car
battery.
1 Touch the upper left corner to display home
menu.
2 Touch [Navigation].
The navigation menu is displayed in a few »
seconds.
3 Refer to the map manual (in Chinese) to
operate the navigation tool.
Tip
You can press NAVI to enter/exit the navigation
system.
Listen to Radio
1
Touch the upper left corner to display home
menu.
2 Touch [Radio].
Band and frequency information is »
displayed..
Play USB device
4
Note
Ensure that the device contains playable content.
1 Open the USB door.
2 Inser t the USB device to the USB socket.
Play starts automatically.»
Note
To remove the USB device, switch to disc, radio
RURWKHUVRXUFHÀUVW
Play SD/MMC card
5
Note
Ensure that the device contains playable content.
The unit supports SDHC card.
1 Open the SD/SDHC card cover.
2 Inser t the SD/MMC card into the SD/MMC
card slot.
Play starts automatically.»
Play with Bluetooth device
Pair the Bluetooth-enabled devices
To connect your Bluetooth device to the unit, you
need to pair the device to the unit. Pairing needs
only to be done once.
You can pair up to eight devices.
1 Search for Bluetooth device with the device.
2 Select “CID3283” in the pairing list.
Receive call
By default, all incoming calls are received automatically.
1 If there is incoming call, [Incoming call...]
ÁDVKHVRQWKHVFUHHQ6SHDNLQWRWKH
Bluetooth microphone.
2 When conversation ends, touch (red) to
terminate the call.
Tip
You can select to receive calls manually by set
[Auto answer] to [Off] status.
3 Touch [Settings].
4 Touch [Time].
» The date/time setup menu is displayed.
Set date
1 Touch [Date].
2 Touch on the displayed date information.
A submenu is displayed.»
3 Touch or to set year, month and day.
Set clock mode
1 Touch [Clock mode].
Yellow Green Blue
Red
Black
Yellow
Blue/
white
Pink
Green/white
White/
brown
orange/
white
Brown/
black
orange/
white
Brown/
black
Red
White
Yellow
Red
White
Yellow
White
White
Red
Red
Brown
AV system
AUX
Gearbox
Optional accessory
GPS antenna
Radio antenna
Yellow
Yellow
Rear display
Rear display
Amplifier
a Connect the AV cable to the AV IN socket on the front panel
a
-
1
Philips CID3283/93 Guide de démarrage rapide
- Catégorie
- Récepteurs multimédia de voiture
- Taper
- Guide de démarrage rapide
- Ce manuel convient également à
dans d''autres langues
- English: Philips CID3283/93 Quick start guide