Kohler 29709-WB-VS Guide d'installation

1387795-2-C

Installation Instructions

Record your model number:

Noter le numéro de modèle:

Anote su número de modelo:

Français, page 19

Español, página 37

Touchless Kitchen Faucet

Thank You for Choosing KOHLER

Need help? Contact our Customer Care Center.

• USA/Canada: 1-800-4KOHLER (1-800-456-4537) Mexico: 001-800-456-4537

•Service parts: kohler.com/serviceparts

•Care and cleaning: kohler.com/clean

•Patents: kohlercompany.com/patents

Warranty

This product is covered under the KOHLER® Electronic Faucets, Valves, and

Controls Five-Year Limited Warranty, found at kohler.com/warranty. For a hardcopy

of warranty terms, contact the Customer Care Center.

Tools and Materials

3/8"

Plus:

• Unswitched Electrical Outlet

• Fasteners

1387795-2-C2 Kohler Co.

Important Information

WARNING: When using electrical products, basic precautions should

always be followed, including the following:

DANGER: Risk of electric shock. Connect only to a circuit protected by a

Ground-Fault Circuit-Interrupter (GFCI)*.

WARNING: Risk of electric shock. Grounding is required. A qualied

electrician should make all electrical connections.

WARNING: Risk of electric shock. Disconnect the power before servicing.

WARNING: Risk of injury or property damage. Read all instructions

thoroughly before beginning installation.

CAUTION: Risk of fresh water contamination. This faucet contains back-

siphonage protection. To prevent water contamination, do not remove any

internal components.

CAUTION: Risk of property damage. The faucet spout contains a magnet. Do

not allow items susceptible to electromagnetic damage to come into close

proximity to the spout.

CAUTION: Risk of product damage. This product contains sensitive

electronic components. Do not store open containers of chemical or cleaning

products near this product. Cleaning rags or sponges must be rinsed with

fresh water before storage.

IMPORTANT! Do not use a switch-controlled electrical outlet (typically used for

garbage disposals) to provide power to the faucet.

Follow all local plumbing, building, and electrical codes.

Provide a constant unswitched 120 VAC electrical outlet located below the sink

within 5' (1.5 m) of the control box.

For uneven mounting surfaces (such as tile grout lines), apply a suitable sealant

under the faucet. Do not use petroleum-based sealant.

Class 1 laser product: Complies with 21 CFR 1040.10 and 1040.11.

*Outside North America, this may be known as a Residual Current Device (RCD).

Kohler Co. 3 1387795-2-C

1. Install the Faucet

Ring

Outlet Hose

1/4"

(6 mm)

NOTE: Handle orientation is designed to be on the right.

Turn OFF the water supplies.

For three-hole sinks, install an escutcheon.

Thread the screws into the ring 1/4" (6 mm) past the surface.

Insert the faucet through the mounting surface with the handle on the right.

Slide the washer and ring over the outlet hose, then feed the supply hoses and

wires through the washer and ring.

Thread the ring onto the shank until the washer contacts the underside of the sink.

Adjust the ring to align the screws with the front and back of the faucet.

Securely tighten the screws.

1387795-2-C4 Kohler Co.

2. Connect the Supplies

Weight

Outlet Hose

Ø 3"

(76 mm)

Min

Outlet

Hose

Inlet

Outlet

Spray

Hose

Flow

Sensor

CAUTION: Risk of restricted water ow and product damage. The supply

hoses must not be taut, kinked, or twisted. If the supply hoses must be coiled,

maintain an inside diameter of 3" (76 mm).

Connect the Water Supplies

Connect and tighten the supply hoses to the supply stops.

Place a bucket under the outlet hose.

Turn ON the water supplies.

Flush hot and cold water for 1 minute to remove any debris.

Connect the ow sensor and outlet hose to the solenoid inlet.

Connect the Spray Hose

NOTE: The weight must be installed onto the spray hose to act as a pull stop and to

prevent kinking damage.

Remove the protective cap.

Slide the weight onto the spray hose.

Connect the spray hose to the solenoid outlet.

Kohler Co. 5 1387795-2-C

3. Connect the Wires

Handle Switch Solenoid

Sensor Power LED

Apply grease.

Connector Status LEDs

Flow Sensor

Apply grease (provided) to the sensor socket located on the circuit board inside

the cover. This will provide additional corrosion protection.

Connect the handle switch wire from the faucet to the handle switch connector on

the circuit board.

Connect the sensor wire from the faucet to the sensor connector on the circuit

board.

Connect the power cord to the power cord connector on the circuit board.

Connect the solenoid wire to the solenoid connector on the circuit board.

Plug the power supply into an unswitched 120 VAC outlet. The power LED on the

circuit board will illuminate.

Test activation of the sensor. Refer to the “Faucet Operation” section.

Connect Your Faucet

Download the KOHLER Konnect app.

Follow the app instructions to connect to your faucet.

1387795-2-C6 Kohler Co.

NOTE: Setup must be completed within 10 minutes.

When the Connector Status LED illuminates red, the system is ready for mobile

app setup.

If the Connector Status LED is ashing red, unplug the power cord to reset the

system.

When the Connector Status LED is ashing red and green, the system is seing

up.

When the Connector Status LED illuminates green, the system is ready for use.

If the Connector Status LED is ashing green, the router connection was lost.

Verify that the router is powered ON and within range.

If the Connector Status LED does not illuminate green, an electronics reset is

needed.

Electronics Reset

Open the handle to turn ON the faucet.

Wave a hand over the sensor to turn OFF the faucet.

Close the handle.

Repeat the above steps 10 times in 1 minute to clear the prole information. If the

above sequence is broken, the count will reset to zero.

Kohler Co. 7 1387795-2-C

4. Install the Solenoid

Solenoid Wire

Tab

Mounting

Bracket

CAUTION: Risk of restricted waterow. The outlet hose must not be taut or

kinked when installed. Locate the solenoid valve within 7" (178 mm) to 8" (203

mm) from the faucet centerline.

NOTE: Allow adequate clearance for servicing.

NOTE: The mounting bracket should be secured with two suitable fasteners (not

supplied) based on the type and thickness of the cabinet or wall material.

NOTE: The solenoid may be positioned to the right or left. Remove the appropriate

tab on the cover.

Position the mounting bracket within 7" (178 mm) to 8" (203 mm) from the faucet

centerline.

Fasten the mounting bracket vertically to the cabinet or wall.

Position the solenoid and cover on the mounting bracket.

Secure the solenoid and cover to the mounting bracket using the two screws

provided.

1387795-2-C8 Kohler Co.

5. Complete the Installation

2" (51 mm) Min

3" (76 mm) Max

Position the Weight

Position the weight between 2" (51 mm) and 3" (76 mm) from the cabinet oor.

Secure the cable tie around the spray hose just below the weight.

Extend and retract the spray hose to check for smooth operation.

Check for Leaks

Turn ON the water supplies.

Check all connections for leaks.

Test the faucet for proper operation. Refer to the “Faucet Operation” section.

Kohler Co. 9 1387795-2-C

Faucet Operation

Sensor

Open Position

Manual

Override

Handle LED

NOTE: Some objects that are clear and certain colors are not detectable by the sensor.

Always use your hand for sensor testing.

Rotate the handle outward to the open position to start water ow. The handle

LED will illuminate to indicate that the sensor is functioning.

Adjust the handle to the desired water temperature.

Wave your hand under the sensor to turn OFF the water.

Wave your hand under the sensor again to restart the water ow.

If needed, refer to the “Handle LED Adjustment” section for more information.

NOTE: For extended periods of nonuse, return the handle to the closed (upright)

position. The handle LED will turn OFF, indicating that water ow is not available.

Features

Handle LED: Illuminates when the sensor is active.

Power LED: Indicates that there is power to the circuit board.

Automatic shut-o: After 4 minutes of inactivity, the water will automatically

shut OFF.

Sensor override: In the event of power loss, bypass the sensor function by turning

in the override feature on the solenoid valve. The faucet can then be operated

manually.

1387795-2-C10 Kohler Co.

LED Color Indicators

Red LED: System is ready for setup.

Flashing Red LED: Setup was not completed in time. System will need to be reset.

Green LED: The system is connected.

Flashing Green LED: The system is not connected.

Kohler Co. 11 1387795-2-C

Handle LED Adjustment

Setscrew

Closed

Position

Open Position

Sensor

Handle

LED

IMPORTANT! Do not apply upward pressure to the valve setscrew while making

adjustments.

NOTE: The LED should turn ON as the handle is rotated open, and OFF when the

handle is in the upright (closed) position. Use a 5/64" hex wrench to adjust the valve

setscrew as needed.

LED is ON when the handle is closed: Tighten the valve setscrew until the LED

turns OFF. Then tighten the setscrew an additional 1/4 turn.

Handle does not return to the upright position: Loosen the valve setscrew until

the handle rotates to the full upright (closed) position and the LED turns ON.

Then tighten the setscrew until the LED turns OFF, plus an additional 1/4 turn.

Water does not fully shut o: Loosen the valve setscrew until the handle rotates

to the full upright (closed) position and the LED turns ON. Tighten the setscrew

until the LED turns OFF, plus an additional 1/4 turn.

1387795-2-C12 Kohler Co.

Cleaning the Screens

Screen

Sprayhead

Screen

Outlet

Hose

Solenoid

Spray

Hose

Sprayhead Screen

Turn the handle to the closed position.

Disconnect the nut at the end of the spray hose.

Remove and clean the screen inside the spray hose.

Reinsert the screen and reconnect the sprayhead.

Solenoid Inlet Screen

Turn the handle to the closed position.

Disconnect the outlet hose from the solenoid.

Remove and clean the inlet screen inside the solenoid.

Reinstall the inlet screen and reconnect the outlet hose.

Kohler Co. 13 1387795-2-C

Troubleshooting

CAUTION: Risk of property damage. This product contains sensitive

electronic components. Use care not to damage pins and connectors during

troubleshooting.

CAUTION: Risk of property damage. Do not insert anything other than the

sensor wire into the sensor wire connector (phone jack) on the circuit board.

This troubleshooting guide is for general aid only. For service and installation issues

or concerns, call 1-800-4KOHLER.

Faucet Troubleshooting

Symptoms Probable Cause Recommended Action

1. No water ow. A. The supply stops

are closed.

B. Handle is in the

closed position.

C. The hot and/or

cold supply hose is

kinked.

D. The outlet hose is

kinked.

E. Handle LED is not

lit.

F. Power LED on

circuit board is not

lit.

G. One or more

screens are

clogged.

A. Conrm that the supply stops are

open.

B. Rotate the handle to the open

position. Refer to the “Faucet

Operation” section.

C. Conrm that the supply hoses are

not kinked. If coiled, maintain an

inside diameter of 3" (76 mm).

D. Conrm that the solenoid valve is

within 7" (178 mm) to 8" (203

mm) from the faucet centerline.

E. Refer to the “Handle Switch

Troubleshooting Table.”

F. Refer to the “Sensor

Troubleshooting Table.”

G. Refer to the “Cleaning the

Screens” section.

1387795-2-C14 Kohler Co.

Symptoms Probable Cause Recommended Action

2. Low water

ow. A. The supply stops

are partially closed.

B. Handle is partially

closed.

C. The hot and/or

cold supply hose is

kinked or twisted.

D. The outlet hose is

kinked.

E. One or more

screens are

clogged.

F. Cracked

diaphragm.

A. Conrm that the supply stops are

fully open.

B. Rotate the handle to the full open

position.

C. Conrm that the supply hoses are

not kinked or twisted. If coiled,

maintain an inside diameter of 3"

(76 mm).

D. Conrm that the solenoid valve is

within 7" (178 mm) to 8" (203

mm) from the faucet centerline.

E. Refer to the “Cleaning the

Screens” section.

F. Replace the solenoid valve

assembly.

3. Poor spray

paern. A. The spray nozzles

are clogged.

A. Rub your nger over the nozzles

with water running to dislodge

debris.

4. Power LED is

not lit. A. No power to the

circuit board.

B. Power cord is

plugged into a

switched outlet.

A. Check the power supply

connections to the circuit board.

B. Plug the power cord into an

unswitched 120 VAC outlet (test

the outlet with a radio or other

device). Conrm that the power

LED illuminates.

5. Water drips or

trickles when

faucet is not in

use.

A. Manual override is

partially engaged.

A. Turn the manual override fully

clockwise; then turn

counterclockwise until the water

drip stops.

Kohler Co. 15 1387795-2-C

Solenoid Troubleshooting

Symptoms Probable Cause Recommended Action

1. Water leaks

from the solenoid

valve.

A. Hose connections

are not secure.

B. Internal leak.

A. CAUTION: Risk of personal

injury or product damage. Turn

OFF the main power and water

supply. Check all connections.

Make adjustments as needed.

B. Replace the solenoid valve

assembly.

2. No audible

“click” when

solenoid is

activated.

A. Loose solenoid

wire connection.

B. Solenoid valve is

not functioning.

A. Check solenoid wire connection

to the circuit board.

B. Replace the solenoid valve

assembly.

Handle Switch Troubleshooting

Symptoms Probable Cause Recommended Action

1. Handle LED is

lit when the

handle is closed.

A. Valve setscrew

needs adjustment.

A. Refer to the “Handle LED

Adjustment” section.

2. Handle does

not return to the

upright position.

A. Valve setscrew

needs adjustment.

A. Refer to the “Handle LED

Adjustment” section.

3. Water does not

fully shut o. A. Valve setscrew

needs adjustment.

A. Refer to the “Handle LED

Adjustment” section.

4. Handle LED

does not

illuminate when

the handle is

rotated open.

A. Loose handle

switch wire

connection.

B. Circuit board is not

functioning

correctly.

A. Check handle switch wire

connection to the circuit board.

B. Replace the cover assembly.

1387795-2-C16 Kohler Co.

Sensor Troubleshooting

Symptoms Probable Cause Recommended Action

1. Intermient

sensor operation. A. Debris on the

sensor lens.

B. Sensor is detecting

steam.

A. Use mild soap and water to

gently remove debris from the

sensor lens.

B. Rotate the spout away from the

steam.

2. Handle LED is

lit, but power

LED is not.

A. Loose sensor wire

connection.

B. Debris on the

sensor wire

connector.

C. Circuit board is not

functioning.

A. Check sensor wire connection to

the circuit board.

B. At the circuit board, gently

disconnect, clean, and reconnect

the sensor wire connector.

C. Replace the cover assembly.

Compliance

Contains FCC ID: Z64-CC3235MOD

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation.

Changes or modications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment o and on, the user is encouraged to try to correct the

interference by one of the following measures:

• Reorient or relocate the receiving antenna.

Kohler Co. 17 1387795-2-C

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Warning

This transmier with its antenna complies with FCC’s RF exposure limits for general

population/uncontrolled exposure. This device must not be co-located or operated in

conjunction with any other antenna or transmier. This device should be operated

with a minimum distance of 7-7/8" (200 mm) between the radiator and your body.

Contains IC: 451I-CC3235MOD

This device contains license-exempt transmier(s)/receiver(s) that comply with

Innovation, Science and Economic Development Canada’s license-exempt RSS(s).

Operation is subject to the following two conditions: (1) this device may not cause

interference, and (2) this device must accept any interference, including interference

that may cause undesired operation of the device.

This transmier with its antenna complies with Industry Canada RF Exposure Limits

for General Population/Uncontrolled Exposure.

This Class B digital apparatus complies with Canadian ICES-003.

1387795-2-C18 Kohler Co.

Instructions d'installation

Robinet de cuisine sans contact

Merci d'avoir choisi KOHLER

Besoin d'aide? Appeler notre centre de services à la clientèle.

• USA/Canada : 1-800-4KOHLER (1-800-456-4537) Mexique : 001-800-456-4537

•Pièces d’entretien : kohler.com/serviceparts

•Entretien et neoyage : kohler.com/clean

•Brevets : kohlercompany.com/patents

Garantie

Ce produit est couvert sous la garantie limitée de cinq ans des commandes, vannes

et robinets électroniques KOHLER®, fournie sur le site kohler.com/warranty. Pour

obtenir une copie imprimée des termes de la garantie, s'adresser au centre de services

à la clientèle.

Outils et matériel

3/8 po

Plus :

• Prise électrique non commutée

• Dispositifs de xation

Kohler Co. 19 1387795-2-C

F

R

Renseignements importants

AVERTISSEMENT : Lors de l'utilisation de produits électriques, toujours

observer les précautions de base, dont les suivantes :

DANGER : Risque de choc électrique. Uniquement connecter à un circuit

protégé par un disjoncteur de fuite de terre (GFCI)*.

AVERTISSEMENT : Risque de choc électrique. Une mise à la terre est

requise. Un électricien qualié doit eectuer toutes les connexions électriques.

AVERTISSEMENT : Risque de choc électrique. Débrancher l'alimentation

électrique avant un entretien.

AVERTISSEMENT : Risque de blessures ou de dommages matériels. Lire

toutes les instructions avec aention avant de commencer l'installation.

ATTENTION : Risque de contamination de l'eau douce. Ce robinet

comprend une protection contre le siphonnement à rebours. An d'éviter la

contamination d'eau, ne pas retirer des composants internes.

ATTENTION : Risque de dommages matériels. Le bec du robinet comprend

un aimant. Ne pas laisser des objets pouvant subir des dommages

électromagnétiques à proximité immédiate du bec.

ATTENTION : Risque d'endommagement du produit. Ce produit contient

des composants électroniques sensibles. Ne pas entreposer des récipients de

produits chimiques ou de neoyage ouverts près de ce produit. Les chions

ou éponges de neoyage doivent être rincés avec de l'eau douce avant le

stockage.

IMPORTANT! Ne pas utiliser de prise de courant commandée par interrupteur

(généralement utilisée pour les broyeurs de déchets) pour fournir une alimentation

au robinet.

Respecter tous les codes locaux en ce qui concerne l'électricité, la plomberie et le

bâtiment.

Trouver une prise électrique continuelle de 120 V c.a. non commutée sous le lavabo à

5 pi (1,5 m) de l'unité de boîtier de commande.

Pour des surfaces de xation inégales (telles que des lignes de joints de carrelage),

appliquer du mastic d'étanchéité adéquat sous le robinet. Ne pas utiliser du mastic

d'étanchéité à base de pétrole.

1387795-2-C20 Kohler Co.

F

R

La page charge ...

Kohler 29709-WB-VS Guide d'installation

Kohler 29709-WB-VS Guide d'installation

dans d''autres langues

Documents connexes

Autres documents