Generac 3800 PSI G0065640 Manuel utilisateur

www.generac.com or 1-888-436-3722

Operator's Manual

Power Washer

Introduction ............................................................. 1

Safety Rules ........................................................... 1

Safety Symbols and Meanings ..................................................2

General Information ................................................ 3

Know Your Power Washer .........................................................4

Emissions

Information ..............................................................5

Unpacking .................................................................................5

Set-up ..................................................................... 5

Assembly ..................................................................................5

Add Engine Oil ..........................................................................6

Check Pump Oil ........................................................................7

Add Fuel ...................................................................................7

Connect Hose and Water Supply to Pump .................................8

How to Use Nozzles ..................................................................9

Operation .............................................................. 12

Operation ................................................................................12

Power Washer Location ..........................................................12

Checklist Before Starting Engine ..............................................12

How to Start Your Power Washer ............................................12

Automatic Cool Down System (Thermal Relief) .......................14

Adjustable Pressure Setting .....................................................14

How to Stop Your Power Washer .............................................14

Maintenance ......................................................... 15

Maintenance Recommendations ..............................................15

Maintenance

Schedule ............................................................15

Emissions Control ...................................................................15

Power Washer Maintenance ....................................................15

Check and Clean Inlet Screen ..................................................15

Check High Pressure Hoses ....................................................15

Check Detergent Siphoning Tube .............................................15

Check Spray Gun ....................................................................16

Nozzle Maintenance ................................................................16

Pump Oil Maintenance ............................................................16

Engine Maintenance ................................................................17

Engine Oil Recommendations ..................................................17

Service Air Cleaner .................................................................18

Service Spark Plug ..................................................................18

Inspect Muffler and Spark Arrestor ..........................................19

After Each Use ........................................................................19

Winter Storage ........................................................................20

Long Term Storage..................................................................20

Other Storage Instructions .......................................................20

Transporting/Tipping of the Unit ..............................................20

Troubleshooting .................................................... 21

Troubleshooting Guide .............................................................21

Notes .................................................................... 22

Table of Contents

(000004)

WARNING

California Proposition 65. Engine exhaust and some of

its constituents are known to the state of California to

cause cancer, birth defects, and other reproductive

harm.

(000005)

WARNING

California Proposition 65. This product contains or

emits chemicals known to the state of California to

cause cancer, birth defects, and other reproductive

harm.

INTRODUCTION

Thank you for purchasing a Generac Power Systems Inc. product.

This unit has been designed to provide high-performance, efficient

operation, and years of use when maintained properly.

Read this manual thoroughly and understand all of the instructions,

cautions, and warnings before using this equipment. If any section

of the manual is not understood, contact your nearest authorized

dealer, or contact Generac Customer Service at 1-888-436-3722,

or www.generac.com with any questions or concerns.

The owner is responsible for proper maintenance and safe use of

the equipment. Before operating, servicing or storing this power

washer:

• Study all warnings in this manual and on the product carefully.

• Become familiar with this manual and the unit before use.

• Refer to the Assembly section of the manual for instructions on

final assembly procedures. Follow the instructions completely.

Save these instructions for future reference. ALWAYS supply this

manual to any individual that will use this machine.

THE INFORMATION CONTAINED HEREIN WAS BASED ON

MACHINES IN PRODUCTION AT THE TIME OF PUBLICATION.

GENERAC RESERVES THE RIGHT TO MODIFY THIS MANUAL AT

ANY TIME.

WHERE TO FIND US

You can contact Generac Customer Service by phone at 1-888-

436-3722, or on the internet at www.generac.com. Record the

important information of the unit in the following chart for future

reference and/or service inquiries.

Model Number

Serial Number

Date Purchased

SAFETY RULES

Throughout this publication, and on tags and decals affixed to

the power washer, DANGER, WARNING, CAUTION and NOTE

blocks are used to alert personnel to special instructions about

a particular operation that may be hazardous if performed

incorrectly or carelessly. Observe them carefully. Their definitions

are as follows:

(000001)

DANGER

Indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

(000002)

WARNING

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

(000003)

CAUTION

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

NOTE:

Notes contain additional information important to a procedure

and will be found within the regular text body of this manual.

These safety warnings cannot eliminate the hazards that they

indicate. Common sense and strict compliance with the special

instructions while performing the action or service are essential to

preventing accidents.

Introduction

1

SAFETY SYMBOLS AND MEANINGS

(000103)

DANGER

Asphyxiation. Running engines produce carbon

monoxide, a colorless, odorless, poisonous gas.

Carbon monoxide, if not avoided,

will result in death or serious injury.

(000104)

DANGER

Electrocution. Water contact with a power source,

if not avoided, will result in death or serious injury.

(000106)

DANGER

Fluid Injection. This machine produces high-

pressure uid streams that can pierce skin.

Fluid injection will result in death or serious

injury.

(000105)

DANGER

Explosion and Fire. Fuel and vapors are extremely

ammable and explosive. Add fuel in a well

ventilated area. Keep re and spark away. Failure to

do so will result in death or serious injury.

(000110)

WARNING

Risk of Fire. Hot surfaces could ignite

combustables, resulting in re. Fire could result

in death or serious injury.

(000101)

WARNING

Vision Loss. Eye goggles are required to be worn

when using this machine. Failure to wear eye

goggles could result in permenant vision loss.

(000107)

WARNING

Hearing Loss. Hearing protection is recommended

when using this machine. Failure to wear hearing

protection could result in permenant hearing loss.

(000108)

WARNING

Hot Surfaces. When operting machine, do not

touch hot surfaces. Keep machine away from

combustables during use. Hot surfaces

could result in severe burns or re.

(000109)

WARNING

Risk of Fire. Verify machine has properly cooled

before installing cover and storing machine.

Hot surfaces could result in re.

(000111)

WARNING

Moving Parts. Keep clothing, hair, and appendages

away from moving parts. Failure to do so could

result in death or serious injury.

(000112)

WARNING

Risk of Falling. Use of machine creates wet areas

and trip hazards. Be aware of work area conditions.

A fall could result in death or serious injury.

(000114)

WARNING

Risk of Falling. Do not use this machine or any

components on elevated surfaces. Doing so can

result in a fall, serious injury or death.

(000113)

WARNING

Recoil Hazard. Recoil could retract unexpectedly

if water pressure is not properly relieved from

pump, creating kickback. Kickback

could result in death or serious injury.

(000100)

WARNING

Consult Manual. Read and understand manual

completely before using machine. Failure to

completely understand manual and machine

could result in death or serious injury.

(000115)

WARNING

Moving Parts. Do not wear jewelry when starting

or operating this product. Wearing jewelry while

starting or operating this product could result

in death or serious injury.

(000117)

WARNING

Do not aim spray gun at people, animals, electrical devices,

or fragile items. Keep out of reach of children.

Death or serious injury could result.

Safety Rules

2

NOTE:

High pressure spray may damage fragile items including

glass.

• DO NOT point spray gun at glass when using red (0°) MAX nozzle.

• NEVER aim spray gun at people, animals, electrical devices or plants.

NOTE:

Improper treatment of power washer can damage it and

shorten its life.

• If you have questions about intended use, ask dealer or contact

qualified

service center.

• NEVER operate units with broken or missing parts, or without

protective housing or covers.

• DO NOT by-pass any safety device on this machine.

• DO NOT operate power washer above rated pressure.

• DO NOT modify power washer in any way.

• Before starting power washer in cold weather, check all parts of the

equipment to be sure ice has not formed there.

• NEVER move machine by pulling on hoses. Use handle provided on

unit.

• Check fuel system for leaks or signs of deterioration, such as chafed

or spongy hose, loose or missing clamps, or damaged tank or cap.

Correct all defects before operating power washer.

• This equipment is designed to be used with Generac authorized parts

ONLY. If equipment is used with parts that DO NOT comply with

minimum specifications, user assumes all risks and liabilities.

Safety Rules

3

4

KNOW YOUR POWER WASHER

Read this owner’s manual and safety rules before operating your

power washer.

If you loan this device to someone, ALWAYS loan ALL instructional

documentation to the individual as well. Compare the illustrations

with your high power washer to familiarize yourself with the

locations of various controls (Figure 1). Save this manual for future

reference. Replacement owner’s manuals can be printed from the

Generac Web site.

A - Spray Gun – Controls the application of water onto the

cleaning surface with trigger device. Includes a trigger lock.

B - Lance with Quick Connect – Allows you to switch between

four different nozzles.

C - High Pressure Hose – Connect one end to water pump and

the other to the spray gun.

D - Recoil Starter – Use for starting the engine.

E - Oil Fill – Check and add engine oil here.

F - Air Filter – Protects engine by filtering dust, and debris out of

the intake air.

G - Pump – Develops high pressure.

H - Thermal Relief Valve – Cycle’s water through the pump when

water reaches 125°F. Warm water will discharge from pump

onto ground. This prevents internal pump damage.

I - Engine On/Off Switch – Run this switch to “ON” before using

the recoil starter. Turn the switch to “OFF” to stop the engine.

J - Pressure Control/Unloader Valve – Controls the high pressure

output.

K - High Pressure Outlet – Connection for high pressure hose.

L - Water Inlet – Connection for Garden Hose.

M - Fuel Tank – Fill tank with regular unleaded fuel. Always leave

room for fuel expansion.

N - Fuel On/Off Switch – Turns fuel supply to the engine on and

off.

O - Choke – Prepares a cold engine for starting.

P - Throttle Lever – Increases or decreases engine speed. Throttle

should be at maximum travel when the pressure washer is in

use.

Q - Nozzles – Chemical injection, 0°, 15°, 25°, 40° (white, yellow,

red and black) for various high pressure cleaning applications.

R - Pull Pin – Pull the ring to unlock the handle. This allows the

handle to be collapsed for storage.

S - Adjustable Side Handle – Adjustable by turning counter clock-

wise to loosen, adjust to comfortable position and tighten

clock-wise. This allows for a firm operating grip of the spray

gun.

T - Oil Drain – Drain engine oil here.

U - Serial Number Location

ITEMS NOT SHOWN

Identification Label (near rear of base plate) – Provides model

and serial number of pressure washer. Please have these readily

available if calling for assistance.

Detergent Siphoning Tube/Filter – Use to siphon pressure washer

safe detergents into the low pressure stream.

General Information

A

C

F

Q

R

D

B

M

I

P

O

N

J

K

L

H

G

S

T

E

U

Figure 1 – Features & Controls

5

Set-up

EMISSIONS INFORMATION

The U.S. Environmental Protection Agency (and California Air

Resource Board for equipment certified to CA standards) requires

that this engine comply with exhaust and evaporative emission

standards. Locate the emissions compliance decal on the engine

to determine what standards the engine meets, and to determine

which emissions warranty applies. The engine is certified to meet

the applicable emission standards on gasoline. It is important to

follow the maintenance specifications in the Maintenance section

to ensure that the engine complies with the applicable emission

standards for the duration of the product’s life. This engine utilizes

lean carburetion settings and other systems to reduce emissions.

Tampering with or altering the emission control system may

increase emissions and may be a violation of Federal or California

Law. Acts that constitute tampering include but are not limited to:

• Removal or alteration of any part of the intake, fuel, or exhaust systems

• Altering or defeating the governor linkage or speed-adjusting mechanism

to cause the engine to operate outside its design parameters

If you are aware of any of the following symptoms, have your

engine inspected and repaired by your servicing dealer:

• Hard starting or stalling after starting

• Rough idle

• Misfiring or backfiring under load

• Afterburning (backfiring)

• Black exhaust smoke or high fuel consumption

UNPACKING

1. Remove the parts bag, accessories, and inserts included with

power washer.

2. Open carton completely by cutting each corner from top to

bottom.

3. Ensure you have all included items prior to assembly.

• Main Unit

• High Pressure Hose

• Siphon Hose & Filter

• Spray Gun

• Lance with Quick Connect Fitting

• Oil Bottle

• Parts Bag (which includes the following):

– Hose Hook Wireform with Screws and Allen Wrench

– Operator’s Manual

– Owner’s Registration Card

– Bag containing Color-coded Nozzles

– Filter Screen

4. If you are missing any items from your carton, please call

Generac Customer Service at 1-888-436-3722. When calling

for assistance, please have the model and serial number from

the data tag available.

5. Fill out and send in registration card. Write Model number,

Serial number & date of purchase in the table located in the

"Where to Find Us" section.

ASSEMBLY

(000100)

WARNING

Consult Manual. Read and understand manual

completely before using machine. Failure to

completely understand manual and machine

could result in death or serious injury.

Call Generac Customer Service at 1-888-436-3722 for any

assembly issues or concerns. Please have the model and serial

number available.

1. The handle may be folded down or locked into position using

the integrated pull pin.

Figure 2 – Attach Handle

A

2. Install hose hook using provided screws and allen wrench

(Figure 3).

Figure 3 – Install Hose Hook

3. Insert color-coded nozzles in spaces provided in handle

(Figure 4).

4. Place spray gun and nozzle extension into spray gun holder as

shown (Figure 4).

6

Set-up

Figure 4 – Insert Nozzles

5. Coil high pressure hose and hang on hook.

6. Attach siphon tube to location A (Figure 5).

Figure 5 – Siphon Tube Location

A

ADD ENGINE OIL

1. Place power washer on a flat, level surface.

2. Clean area around oil fill and remove orange oil fill cap/dipstick

(Figure 6).

Figure 6 – Fill Engine Oil

000115

3. Using oil funnel (optional), slowly pour oil into oil fill opening.

See Maintenance section for oil type recommendation.

NOTE:

On some units there is more than one oil fill location. In these

instances it is only necessary to use one of the oil fill points.

4. Check periodically until the oil level is between "L" and "H" on

the dipstick (Figure 7). DO NOT OVERFILL.

NOTE:

Any attempt to crank or start the engine before it has been

properly serviced with the recommend oil may result in engine

failure.

5. Replace oil fill cap/dipstick and fully tighten.

Figure 7 – Dipstick

000116

7

Set-up

CHECK PUMP OIL

1. Place power washer on a flat, level surface.

2. Clean area around oil fill and remove vented cap/dipstick (B)

(Figure 8).

Figure 8 – Check Pump Oil

A

B

3. Check to confirm oil level is between the "L" and "H" on the

dipstick (Figure 9). If oil is required, see Maintenance section.

DO NOT OVERFILL.

4. See the Maintenance section for additional information on

pump oil maintenance.

5. Install oil dipstick until finger tight.

6. Clean up any spilled oil.

Figure 9 – Pump Oil Dipstick

“H”

Acceptable Oil

Level Range

“L”

ADD FUEL

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON).

• Gasoline with up to 10% ethanol (gasohol) is acceptable.

NOTE:

Avoid power washer damage. Failure to follow Operator’s

Manual for fuel recommendations voids warranty.

• DO NOT use unapproved gasoline such as E85.

• DO NOT mix oil in gasoline.

• DO NOT modify engine to run on alternate fuels.

To protect the fuel system from gelling, mix in a fuel stabilizer when

adding fuel. See Storage. All fuel is not the same. If you experience

starting or performance problems after using fuel, switch to a

different fuel provider or change brands.

(000105)

DANGER

Explosion and Fire. Fuel and vapors are extremely

ammable and explosive. Add fuel in a well

ventilated area. Keep re and spark away. Failure to

do so will result in death or serious injury.

WHEN ADDING FUEL

• Turn power washer OFF and let it cool at least two (2) minutes

before removing fuel cap. Loosen cap slowly to relieve pressure in

tank.

• Fill fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

1. Clean area around fuel fill cap, remove cap.

2. Slowly add regular unleaded fuel to fuel tank. Be careful not

to overfill. Fill to bottom of filter screen, this will allow for fuel

expansion (Figure 10).

3. Install fuel cap and let any spilled fuel evaporate before

starting engine.

Figure 10 – Adding Fuel

000117

8

CONNECT HOSE AND WATER SUPPLY TO PUMP

NOTE:

DO NOT run the pump without the water supply connected

and turned on. Damage to equipment resulting from failure to

follow this instruction will void warranty.

NOTE:

Remove and discard the shipping cap from the pump’s water

inlet before attaching hose.

1. Run water through your garden hose for 30 seconds to clean

out any debris.

2. Before connecting garden hose to water inlet, inspect inlet

screen before installing (A) (Figure 11). The cone should face

outward. Clean screen if it contains debris or have it replaced

if damaged. DO NOT run power washer if inlet screen is

damaged.

IMPORTANT: DO NOT siphon standing water for the water supply.

Use ONLY cold water (less than 100°F). Water supply must be

adequate to handle greater than 3.8 gallons per minute and no less

than 30 psi.

NOTE:

Using a One Way Valve (vacuum breaker or check valve) at

pump inlet can cause pump or inlet connector damage.

• There MUST be at least ten feet of unrestricted garden hose between

the power washer inlet and any device, such as a vacuum breaker or

check valve.

• Damage to equipment resulting from failure to follow this instruction

will void warranty.

Figure 11 – Inspect Inlet Screen

A

3. Connect the garden hose (not to exceed 50 feet in length) to

the water inlet (Figure 12). Tighten by hand.

Figure 12 – Connect Garden Hose

(000101)

WARNING

Vision Loss. Eye goggles are required to be worn

when using this machine. Failure to wear eye

goggles could result in permenant vision loss.

• Always wear safety goggles when using this equipment or in vicinity

of equipment in use.

• Before starting the power washer, be sure you are wearing adequate

safety goggles.

• NEVER substitute safety glasses for safety goggles.

4. Connect lance to spray gun (Figure 13). Tighten by hand.

Figure 13 – Attach Lance

000119

5. Attach end of high pressure hose to base of spray gun

(Figure 14).

(000106)

DANGER

Fluid Injection. This machine produces high-

pressure uid streams that can pierce skin.

Fluid injection will result in death or serious

injury.

Set-up

9

• NEVER connect high pressure hose to lance.

• Keep high pressure hose connected to pump and spray gun while

system is pressurized.

• Always be certain spray gun, nozzles and accessories are

correctly attached.

Figure 14 – Connect Hose to Spray Gun

6. Connect high pressure hose to pump (uncoil hose before

connecting to pump or spray gun) (Figure 15).

Figure 15 – Connect High Pressure Hose to Pump

7. Turn ON the water, squeeze the trigger to purge the pump

system of air (Figure 16).

(000124)

CAUTION

Equipment damage. The hose can be damaged if it

comes in contact with the hot engine muer. Keep

hose away from muer during operation.

Figure 16 – Squeeze Trigger

000123

HOW TO USE NOZZLES

The quick–connect on the nozzle lance allows you to switch

between different nozzles. Nozzles can be changed while the

power washer is running, once the spray gun trigger is locked

in the safety position. The nozzles vary the pressure and spray

pattern as shown.

• For the most effective cleaning, keep the nozzle from 8 to 24 inches

(20 to 61 cm) away from the surface being cleaned.

• If you get the nozzle too close, especially using a high pressure nozzle,

you may damage the surface being cleaned.

(000106)

DANGER

Fluid Injection. This machine produces high-

pressure uid streams that can pierce skin.

Fluid injection will result in death or serious

injury.

• NEVER exchange nozzles without the trigger lock being engaged on

the spray gun.

• DO NOT twist nozzles while spraying.

Follow these instructions to change nozzles:

1. Pull back the collar on the quick–connect and pull the current

nozzle off. Store nozzles in the accessory storage holder

(Figure 17).

Figure 17 – Nozzles

000125

Set-up

10

2. Select desired nozzle:

3. Pull back on the collar, insert the new nozzle and release the

collar. Tug on the nozzle to make sure it is securely in place.

• The WHITE NOZZLE is used for delicate rinse (lower pressure and

higher flow), for gentle cleaning of cars/trucks, boats, RV’s, patio

furniture, lawn equipment, etc. (Figure 18).

Figure 18 – Wash Pressure Nozzle (White)

• The GREEN NOZZLE is for general rinsing (medium pressure and

medium flow), ideal for most all purpose cleaning such as home

siding, brick patios, wood decks, driveways and sidewalks, garage

floors, etc. (Figure 19).

Figure 19 – Clean Pressure Nozzle (Green)

• The yellow nozzle is for medium rinsing (higher pressure and

medium flow), ideal for removing stains on hard porous surfaces

such as concrete dirveways, garage floors and brick patios, select

yellow nozzle (Figure 20).

Figure 20 – Strip Pressure Nozzle (Yellow)

• The RED NOZZLE is for maximum rinsing (higher pressure and

lower flow); for stubborn or hard to reach surface such as second

story surfaces, paint removal, oil stains, rust removal or other

stubborn substances (tar, gum, grease, wax, etc.) (Figure 21).

(000125)

CAUTION

This nozzle can damage work surfaces if it is too close,

or held in one position for an extended period of time.

Figure 21 – Blast Pressure Nozzle (Red)

• Use the BLACK NOZZLE when applying detergent (Figure 22).

Only use power washer safe detergents/soaps to help break down

stubborn dirt and grime on a variety of surfaces.

Figure 22 – Detergent Nozzle (Black)

Set-up

11

CLEANING AND APPLYING DETERGENT

(000126)

WARNING

Chemicals can cause bodily injury, and/or

property damage.

• NEVER use caustic liquid with the power washer.

• Use ONLY power washer safe detergents/soaps. Follow all

manufacturer's instructions.

To apply detergent, follow these steps:

1. Review proper use of nozzles.

2. Prepare detergent solution as required by the job into a

container located within the proximity of the siphon tube.

3. Make sure the siphoning tube remains fully submerged into

the detergent.

NOTE:

Make sure the filter remains fully submerged in detergent

while applying detergent.

NOTE:

Contact with the hot muffler can damage the detergent

siphoning tube.

4. When inserting the siphon into a detergent solution bottle, route the

tube so as to keep it from inadvertently contacting the hot muffler.

5. Make sure the black detergent nozzle is installed.

NOTE:

Detergent cannot be applied with the high pressure nozzles

(Yellow, White, Green or Red). Only use the Black nozzle with

detergent.

6. Confirm that all set-up instructions have been followed.

NOTE:

You must attach all the hoses before you start the engine.

• Starting the engine without all the hoses connected, and without

the water turned ON, will damage the pump.

• Damage to the equipment resulting from failure to follow these

instructions will void the warranty.

7. Start engine following instructions How to Start Your Power

Washer.

8. Apply detergent to a dry surface, starting at the lower portion

of the area to be washed and work upward using long, even,

overlapping strokes.

9. Allow the detergent to "soak in" for 3-5 minutes before

washing and rinsing. Reapply as needed to prevent the

surface from drying. DO NOT allow the detergent to dry on the

surface being cleaned (prevents streaking).

IMPORTANT: You must flush the detergent siphoning system after

each use by placing the filter into a bucket of clean water, then run

the power washer in low pressure for 1-2 minutes.

POWER WASHER RINSING

1. Remove the black detergent nozzle from the lance.

2. Select and install the desired high pressure nozzle following

the instructions How to Use Nozzles.

3. Point the spray gun in a safe direction and away from people,

animals and plants. Squeeze the trigger to flush any remaining

chemicals from the system.

4. Keep the spray gun a safe distance from the area you plan to

spray.

(000112)

WARNING

Risk of Falling. Use of machine creates wet areas

and trip hazards. Be aware of work area conditions.

A fall could result in death or serious injury.

(000114)

WARNING

Risk of Falling. Do not use this machine or any

components on elevated surfaces. Doing so can

result in a fall, serious injury or death.

(000113)

WARNING

Recoil Hazard. Recoil could retract unexpectedly

if water pressure is not properly relieved from

pump, creating kickback. Kickback

could result in death or serious injury.

• Use only on a level surface.

• Do not use on an elevated surface to prevent the risk of a serious fall.

• Firmly grasp the spary gun with both hands when using the high

pressure spray to avoid injury when the spray gun kicks back.

5. Apply a high pressure spray to a small area and then check

surface for damage. If no damage is found, you can assume

it is okay to continue rinsing.

6. Start at the top of the area to be rinsed, working down with the

same overlapping strokes used for cleaning.

CLEANING DETERGENT SIPHONING TUBE

If you used the detergent siphoning tube, you must flush it with

clean water before stopping the engine.

1. Place the detergent siphoning tube/filter in a bucket full of

clean water.

2. Remove the high pressure nozzle from the nozzle extension.

3. Select and install the black detergent nozzle following the

instructions How to Use Nozzles.

4. Flush for 1-2 minutes.

5. Shut the engine off following the instructions How to Stop

Power Washer, and turn off water supply.

6. ALWAYS point the spray gun in a safe direction, squeeze the

spray gun trigger to release retained high water pressure.

Engage the trigger lock when not in use.

Set-up

12

IMPORTANT: Spray gun traps high water pressure, even when the

engine is stopped and water is disconnected.

(000106)

DANGER

Fluid Injection. This machine produces high-

pressure uid streams that can pierce skin.

Fluid injection will result in death or serious

injury.

• Keep the high pressure hose connected to the pump and spray

gun while the system is pressurized.

• ALWAYS point the spray gun in a safe direction, and squeeze

the spray gun trigger to release high pressure every time you

stop the engine. Engage the trigger lock when not in use.

OPERATION

If you have any problems operating your power washer, please call

Generac customer service at 1-888-436-3722.

POWER WASHER LOCATION

Clearances and Air Movement

(000103)

DANGER

Asphyxiation. Running engines produce carbon

monoxide, a colorless, odorless, poisonous gas.

Carbon monoxide, if not avoided,

will result in death or serious injury.

NOTE:

For more information, reference the Carbon Monoxide

warnings in the Safety Rules section.

Place the power washer outdoors, in an area that will not

accumulate deadly exhaust gas. NEVER place the power washer

where exhaust gas could accumulate and enter inside, or be

drawn into a potentially occupied building. Ensure the exhaust

gas is kept away from any windows, doors, ventilation intakes,

or other openings that can allow the exhaust gas to collect in a

confined area. Prevailing winds and air currents should be taken

into consideration when positioning the power washer (Figure 23).

• Operate the power washer outdoors ONLY.

• Keep the exhaust gas from entering a confined area through

windows, doors, ventilation intakes, or other openings.

• NEVER start or run engine indoors, in a vehicle, or in an enclosed

area, EVEN IF windows and doors are open.

(000110)

WARNING

Risk of Fire. Hot surfaces could ignite

combustables, resulting in re. Fire could result

in death or serious injury.

• Keep at least 5 ft. (152 cm) clearance on all sides of the power

washer including overhead.

Figure 23 – Building Clearances

000126

CHECKLIST BEFORE STARTING ENGINE

1. Be sure to read and understand the Operator Safety section

and the Operation section before using the power washer.

2. Check that oil is at the proper level in the engine crankcase and

that fuel has been added to the fuel tank.

3. Review the unit's assembly and ensure the fittings are properly

secured. Also make sure there are no kinks, cuts, or damage

to high pressure hose.

4. Provide a proper water supply at an adequate flow, clear

screens of debris, and confirm that the system is purged of air.

5. Confirm that the unit is on secure, level ground and the

surrounding work area is clear.

HOW TO START YOUR POWER WASHER

NOTE:

DO NOT run the pump without the water supply connected and

turned on. Damage to the equipment resulting from failure to

follow these instructions will void warranty.

1. Move fuel valve (B) to ON (Figure 24).

2. Move choke lever (A) to CLOSE.

Figure 24 – Fuel Valve

000127

Operation

B

A

13

NOTE:

For a warm engine, be sure the choke lever is in the “OPEN”

position.

3. See Figure 25. Turn engine switch ON.

Figure 25 – The ON Position

OFF

ON

000128

(000101)

WARNING

Vision Loss. Eye goggles are required to be worn

when using this machine. Failure to wear eye

goggles could result in permenant vision loss.

• Always wear safety goggles when using this equipment or in the

vicinity of equipment in use.

• Before starting the power washer, be sure you are wearing adequate

safety goggles.

• NEVER substitute safety glasses for safety goggles.

4. Relieve spray gun pressure.

5. Place foot on footpad or otherwise secure the unit from

movement when pulling the recoil.

6. When starting the engine, grasp the starter grip handle (Figure

26) and pull slowly until you feel some resistance. Then pull

rapidly to start engine.

(000113)

WARNING

Recoil Hazard. Recoil could retract unexpectedly

if water pressure is not properly relieved from

pump, creating kickback. Kickback

could result in death or serious injury.

• NEVER pull the starter cord without first relieving the spray gun

pressure.

• When starting the engine, pull the cord slowly until resistance is

felt, then pull rapidly to avoid kickback.

• After each starting attempt, where engine fails to run, always point

the spray gun in a safe direction and squeeze the spray gun trigger

to release high pressure.

• Firmly grasp the spray gun with both hands when using high

pressure spray to avoid injury when the spray gun kicks back.

7. Return the starter grip handle slowly. DO NOT let the rope

“snap back” against the starter.

Figure 26 – Starting the Engine

000129

8. When the engine starts, slowly the move choke lever to the

“OPEN” position (A) as the engine warms. If the engine falters,

move the choke lever to the “CLOSE” position, then to the

“OPEN” position (Figure 27).

Figure 27 – Choke Lever

000127

9. After each starting attempt, where the engine fails to run,

always point the gun in a safe direction, and squeeze the spray

gun trigger to release high pressure.

10. If the engine fails to start after six pulls, move the choke lever

to the “OPEN” position, and repeat steps 6 through 10.

(000106)

DANGER

Fluid Injection. This machine produces high-

pressure uid streams that can pierce skin.

Fluid injection will result in death or serious

injury.

• DO NOT allow CHILDREN to operate the power washer or play

nearby.

• Keep the high pressure hose connected to the pump and spray gun

while the system is pressurized.

• NEVER aim the spray gun at people, animals or electrical devices.

Serious injury will result.

• DO NOT secure the spray gun in the open position.

• DO NOT leave the spray gun unattended while the machine is

running.

• NEVER use a spray gun which does not have a trigger lock or

trigger guard in place and in working order.

Operation

A

14

• Always be certain the spray gun, nozzles and accessories are

correctly attached.

(000108)

WARNING

Hot Surfaces. When operting machine, do not

touch hot surfaces. Keep machine away from

combustables during use. Hot surfaces

could result in severe burns or re.

(000110)

WARNING

Risk of Fire. Hot surfaces could ignite

combustables, resulting in re. Fire could result

in death or serious injury.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow the equipment to cool before touching.

• Keep at least five (5) feet (152 cm) of clearance on all sides of the

power washer including overhead.

• It is a violation of California Public Resource Code, Section 4442,

to use or operate the engine on any forest-covered, brush-covered,

or grass-covered land unless the exhaust system is equipped with

a spark arrester, as defined in Section 4442, maintained in effective

working order. Other states or federal jurisdictions may have similar

laws.

• Replacement parts must be the same and installed in the same

position as the original parts.

AUTOMATIC COOL DOWN SYSTEM (THERMAL

RELIEF)

If you run the engine on your power washer for 3-5 minutes

without pressing the trigger on the spray gun, circulating water

in the pump can reach temperatures above 125°F. The system

engages to cool the pump by discharging the warm water onto

the ground.

ADJUSTABLE PRESSURE SETTING

Your pressure washer pump is equipped with a feature that allows

you to adjust the pressure setting. The pump is preset at the

factory to achieve the highest possible pressure. To decrease the

pressure, turn the pressure control knob counterclockwise to the

desired pressure. Turning the pressure control knob clockwise

until it stops will set the pressure back to the factory setting.

HOW TO STOP YOUR POWER WASHER

1. Release the spray gun trigger.

2. Move the throttle control lever on the engine to the “LOW”

(turtle) position (Figure 28).

Figure 28 – Throttle Position

High Low

3. Turn the engine ON/OFF switch to the "OFF" position.

4. ALWAYS point the spray gun in a safe direction, and the

squeeze spray gun trigger to release retained high water

pressure. Engage the trigger lock when not in use.

5. Turn OFF the water supply.

IMPORTANT: The spray gun traps high water pressure, even when

the engine is stopped and the water is disconnected.

(000106)

DANGER

Fluid Injection. This machine produces high-

pressure uid streams that can pierce skin.

Fluid injection will result in death or serious

injury.

• Keep the high pressure hose connected to the pump and spray gun

while the system is pressurized.

• ALWAYS point the spray gun in a safe direction, squeeze the spray

gun trigger to release high pressure every time you stop the engine.

Engage the trigger lock when not in use.

MAINTENANCE RECOMMENDATIONS

Regular maintenance will improve the performance and extend the life

of the power washer. See any qualified dealer for service.

The power washer’s warranty does not cover items that have been

subjected to operator abuse or negligence. To receive full value

from the warranty, the operator must maintain the power washer

as instructed in this manual, including proper storage as detailed in

Winter Storage and Long Term Storage.

NOTE:

Should you have questions about replacing components on your

power washer, please call 1-888-436-3722 for assistance.

Some adjustments will need to be made periodically to properly

maintain your power washer.

All service and adjustments should be made at least once each

season. Follow the requirements in the Maintenance Schedule chart.

NOTE:

Once a year you should clean or replace the spark plug, clean

or replace the air filter, and check the spray gun and nozzle

extension assembly for wear. A new spark plug and clean air filter

assure proper fuel-air mixture and help your engine run better

and last longer.

Maintenance

15

MAINTENANCE SCHEDULE

Follow the hourly or calendar intervals, whichever occurs first.

More frequent service is required when operating in adverse

conditions.

First 5 Hours

Change engine oil

Every 8 Hours or Daily

Check/clean water inlet screen*

Check high pressure hose

Check detergent siphoning hose/filter

Check spray gun and assembly for leaks

Clean debris

Check engine oil level

Check pump oil level

Every 50 Hours or Every Season

Check/clean air cleaner filter**

Change pump oil**

Change engine oil**

Inspect muffler and spark arrester*

Every 100 Hours or Every Season

Service spark plug

* Clean if clogged. Replace if perforated or torn.

** Service more often under dirty or dusty conditions.

EMISSIONS CONTROL

Maintenance, replacement, or repair of the emissions control

devices and systems may be performed by any non-road engine

repair establishment or individual. However, to obtain ”no

charge” emissions control service, the work must be performed

by a factory authorized dealer. See the Emissions Warranty.

POWER WASHER MAINTENANCE

Clean Debris

Daily or before use, clean accumulated debris from the cleaning

system. Keep the linkage, spring and controls clean. Keep the area

around and behind the muffler free from any combustible debris.

Inspect the cooling air slots and openings on the power washer.

These openings must be kept clean and unobstructed.

Power washer parts should be kept clean to reduce the risk of

overheating and ignition of accumulated debris.

• Use a damp cloth to wipe exterior surfaces clean.

NOTE:

Improper treatment of the power washer can damage it and

shorten its life.

• DO NOT insert any objects through the cooling slots.

• Use a soft bristle brush to loosen caked on dirt, oil, etc.

• Use a vacuum cleaner to pick up loose dirt and debris.

CHECK AND CLEAN INLET SCREEN

Examine the screen on the pump’s water inlet. Clean the screen if

it is clogged, or replace the screen if damaged.

CHECK HIGH PRESSURE HOSES

The high pressure hoses can develop leaks from wear, kinking, or

abuse. Inspect the hoses each time before using them. Check for

cuts, leaks, abrasions or bulging of cover, damage or movement

of couplings. If any of these conditions exist, replace the hose

immediately.

(000106)

DANGER

Fluid Injection. This machine produces high-

pressure uid streams that can pierce skin.

Fluid injection will result in death or serious

injury.

• NEVER repair high pressure hose. Replace it.

• Replacement hose rating MUST meet or exceed maximum

pressure rating of unit.

CHECK DETERGENT SIPHONING TUBE

Examine the filter on the detergent tube and clean it if clogged. The

tube should fit tightly on the barbed fitting. Examine the tube for

leaks or tears. Replace the filter or tube if either is damaged.

CHECK SPRAY GUN

Examine the hose connection to the spray gun and make sure it is

secure. Test the trigger by pressing the trigger, it “springs back”

into place when you release it. Replace the spray gun immediately

if it fails to "spring back".

NOZZLE MAINTENANCE

A pulsing sensation felt while squeezing the spray gun trigger

may be caused by excessive pump pressure. The principal cause

of excessive pump pressure is a nozzle clogged or restricted

with foreign materials, such as dirt, etc. To correct the problem,

immediately clean the nozzle following these instructions:

1. Shut off the engine and turn off the water supply.

2. ALWAYS point the spray gun in a safe direction, squeeze the

spray gun trigger to release retained high water pressure.

(000106)

DANGER

Fluid Injection. This machine produces high-

pressure uid streams that can pierce skin.

Fluid injection will result in death or serious

injury.

• Keep the high pressure hose connected to the pump and spray gun

while the system is pressurized.

• ALWAYS point the spray gun in a safe direction, and squeeze the spray

gun trigger to release high pressure every time you stop the engine.

Engage the trigger lock when not in use.

3. Remove the nozzle from the end of nozzle extension.

Maintenance

16

4. Use a small paper clip to free any foreign material clogging or

restricting the nozzle (Figure 29).

5. Remove the lance from the spray gun.

Figure 29 – Free Foreign Material

000109

6. Using a garden hose, remove additional debris by back

flushing water through the lance (Figure 30) for 30 to 60

seconds.

Figure 30 – Back Flush Lance

7. Reinstall the nozzle into the lance.

8. Reconnect the lance to the spray gun.

9. Make sure the garden hose is connected to the pump water

inlet. Check that the high pressure hose is connected to the

spray gun and pump. Turn on the water.

10. Start the engine following the instructions How to Start Your

Power Washer.

11. Test the power washer by operating it with each quick connect

nozzle.

PUMP OIL MAINTENANCE

Change pump oil every 50 hours of operation.

1. Clean area around oil drain plug (A) (Figure 31).

2. Remove oil drain plug. Drain oil completely.

3. Install oil drain plug. Do not over tighten.

4. Clean Area around oil dipstick (B).

5. Fill pump with SAE 30 non-detergent oil. Oil level must be

between the "L" and "H" mark on dipstick (Figure 32). DO NOT

OVERFILL.

6. Install oil dipstick until finger tight.

7. Clean up any spilled oil.

Figure 31 – Drain Pump Oil

A

B

Figure 32 – Dipstick

“H”

Acceptable Oil

Level Range

“L”

ENGINE MAINTENANCE

(000104)

DANGER

Electrocution. Water contact with a power source,

if not avoided, will result in death or serious injury.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR POWER

WASHER:

• Disconnect the spark plug wire from the spark plug and place the

wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK:

• Use an approved spark plug tester.

• DO NOT check for spark with spark plug removed.

ENGINE OIL RECOMMENDATIONS

We recommend the use of high-quality detergent oils acceptable if

classified for service SF, SG, SH, SJ or higher. DO NOT use special

additives.

Outdoor temperatures determine the proper oil viscosity for the

engine. Use the chart to select the best viscosity for the outdoor

temperature range expected.

Maintenance

17

S A E 3 0 *

1 0 W - 3 0 * *

5 W - 3 0

* Below 50°F (10°C) the use of SAE 30 will result in hard starting.

** Above 80°F (27°C) the use of 10W30 may cause increased oil consumption.

Check oil level more frequently.

NOTE:

Synthetic oil meeting ILSAC GF-2, API certification mark

and API service symbol with “SJ/CF ENERGY CONSERVING”

or higher, is an acceptable oil at all temperatures. Use of

synthetic oil does not alter required oil change intervals.

NOTE:

The engine is equipped with an "Oil Alert System". This

system will automatically stop the engine before the oil level

falls below a safe limit. To avoid the inconvenience of an

unexpected shutdown, always check the engine oil level before

startup.

CHECKING OIL LEVEL

The oil level should be checked prior to each use or at least every

8 hours of operation. Keep the oil level maintained.

1. Make sure the power washer is on a level surface.

2. Clean area around oil fill cap (Figure 34).

3. Remove oil fill cap and wipe dipstick clean.

4. Insert dipstick into filler neck but do not screw it in.

5. Verify oil is at proper level on the dipstick (Figure 35).

6. Replace and tighten oil fill cap, finger tight.

ADDING ENGINE OIL

1. Make sure the power washer is on a level surface.

2. Check the oil level as described in Checking Oil Level section.

3. If level is low, fill until the oil level is between "L" and "H" on the

dipstick (Figure 35).

4. Verify oil level per the Checking Oil Level section.

5. Replace and tighten the oil fill cap, finger tight.

CHANGING ENGINE OIL

If you are using your power washer under extremely dirty or dusty

conditions, or in extremely hot weather, change the oil more often.

(000127)

CAUTION

Avoid prolonged or repeated skin contact with used

motor oil.

• Used motor oil has been shown to cause skin cancer in certain

laboratory animals.

• Thoroughly wash exposed areas with soap and water.

(000128)

CAUTION

Keep out of reach of children.

• Don’t pollute. Conserve resources. Return used oil to collection

centers.

Change oil while the engine is still warm from running as follows:

1. Make sure the unit is on a level surface.

2. Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

3. Clean the area around the oil drain plug (A) (Figure 33). The

oil drain plug is located at the base of the engine, opposite the

carburetor.

Figure 33 – Oil Drain Plug

A

4. Remove the oil fill cap (Figure 34).

5. Remove the oil drain plug and drain oil completely into a

suitable container.

6. Reinstall the oil drain plug and tighten securely.

Figure 34 – Fill Engine Oil

000115

7. Slowly pour oil into the oil fill opening until the oil level is

between "L" and "H" on the dipstick (Figure 35). DO NOT

overfill.

Maintenance

18

Figure 35 – Dipstick

000116

8. Install oil dipstick until finger tight.

9. Clean up any spilled oil.

10. Properly dispose of oil in accordance with all local regulations.

SERVICE AIR CLEANER

Your engine will not run properly and may be damaged if you run it

with a dirty air cleaner. Service more often if operating under dirty

or dusty conditions.

To service the air cleaner, follow these steps:

1. Pull on air cleaner cover latch and remove cover (Figure 36).

2. Loosen wing nut.

3. Carefully remove filter assembly.

4. Remove foam filter.

5. To clean cartridge, gently tap on a flat surface.

6. Reinstall foam filter.

7. Reinstall clean or new cartridge assembly.

8. Reinstall wing nut and tighten.

9. Install cover by snapping latch closed.

Figure 36 – Service the Air Cleaner

Air Cleaner

Cover

Paper Filter

Element

Foam Filter

Element

Gasket

Latch

SERVICE SPARK PLUG

Changing the spark plug will help the engine to start easier and

run better.

1. Clean the area around the spark plug.

2. Remove and inspect the spark plug (Figure 37).

3. Check the electrode gap with a wire feeler gauge and reset the

spark plug gap to the recommended gap, if necessary (see

Specifications).

4. Replace the spark plug if the electrodes are pitted, burned or

the porcelain is cracked. Use the recommended replacement

plug. See Specifications.

5. Install the spark plug and tighten firmly.

Figure 37 – Change the Spark Plug

Maintenance

La page est en cours de chargement...

Generac 3800 PSI G0065640 Manuel utilisateur

Generac 3800 PSI G0065640 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents