Electrolux EFA90540X Manuel utilisateur

EFA 90540 X

EFA 12540 X

Instructions Manual

Manuel d’Instructions

Bedienungsanleitung

Gebruiksaanwijzing

Kullanim Kilavuku

EN

2

Instructions Manual

INDEX

RECOMMENDATIONS AND SUGGESTIONS......................................................................................................................7

CHARACTERISTICS..............................................................................................................................................................8

INSTALLATION....................................................................................................................................................................10

USE.......................................................................................................................................................................................14

MAINTENANCE....................................................................................................................................................................16

FR

3

Manuel d’Instructions

SOMMAIRE

CONSEILS ET SUGGESTIONS ..........................................................................................................................................18

CARACTERISTIQUES.........................................................................................................................................................19

INSTALLATION....................................................................................................................................................................21

UTILISATION........................................................................................................................................................................25

ENTRETIEN..........................................................................................................................................................................27

DE

4

Bedienungsanleitung

INHALTSVERZEICHNIS

EMPFEHLUNGEN UND HINWEISE....................................................................................................................................29

CHARAKTERISTIKEN..........................................................................................................................................................30

MONTAGE............................................................................................................................................................................32

BEDIENUNG.........................................................................................................................................................................36

WARTUNG............................................................................................................................................................................38

NL

5

Gebruiksaanwijzing

INHOUDSOPGAVE

ADVIEZEN EN SUGGESTIES.............................................................................................................................................40

EIGENSCHAPPEN...............................................................................................................................................................41

INSTALLATIE .......................................................................................................................................................................43

GEBRUIK..............................................................................................................................................................................47

ONDERHOUD ......................................................................................................................................................................49

TR

6

Kullanim Kilavuku

IÇERIKLER

TAVSIYELER VE ÖNERILER..............................................................................................................................................51

ÖZELLIKLER........................................................................................................................................................................52

MONTAJ...............................................................................................................................................................................54

KULLANIM............................................................................................................................................................................58

BAKIM...................................................................................................................................................................................60

EN

7

RECOMMENDATIONS AND SUGGESTIONS

The Instructions for Use apply to several versions of this appliance. Ac-

cordingly, you may find descriptions of individual features that do not ap-

ply to your specific appliance.

INSTALLATION

• The manufacturer will not be held liable for any damages resulting from

incorrect or improper installation.

• The minimum safety distance between the cooker top and the extractor

hood is 650 mm.

• Check that the mains voltage corresponds to that indicated on the rating

plate fixed to the inside of the hood.

• For Class I appliances, check that the domestic power supply guarantees

adequate earthing.

Connect the extractor to the exhaust flue through a pipe of minimum di-

ameter 120 mm. The route of the flue must be as short as possible.

• Do not connect the extractor hood to exhaust ducts carrying combustion

fumes (boilers, fireplaces, etc.).

• If the extractor is used in conjunction with non-electrical appliances (e.g.

gas burning appliances), a sufficient degree of aeration must be guaran-

teed in the room in order to prevent the backflow of exhaust gas. The

kitchen must have an opening communicating directly with the open air in

order to guarantee the entry of clean air.

USE

• The extractor hood has been designed exclusively for domestic use to

eliminate kitchen smells.

• Never use the hood for purposes other than for which it has ben designed.

• Never leave high naked flames under the hood when it is in operation.

• Adjust the flame intensity to direct it onto the bottom of the pan only, mak-

ing sure that it does not engulf the sides.

• Deep fat fryers must be continuously monitored during use: overheated oil

can burst into flames.

• Do not flambè under the range hood; risk of fire

• This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience

and knowledge, unless they have been given supervision or instruction

concerning use of the appliance by a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the

appliance

MAINTENANCE

• Switch off or unplug the appliance from the mains supply before carrying

out any maintenance work.

• Clean and/or replace the Filters after the specified time period.

• Clean the hood using a damp cloth and a neutral liquid detergent.

650 mm min.

EN

8

CHARACTERISTICS

Dimensions

650 min.

EN

9

Components

Ref. Q.ty Product Components

1 1 Hood Body, complete with: Controls, Light, Blower,

Filters

2 1 Telescopic Chimney comprising:

2.1 1 Upper Section

2.2 1 Lower Section

7.1 1 Telescopic frame complete with extractor, consisting of:

7.1a 1 Upper frame

7.1b 1 Lower frame

9 1 Reducer Flange ø 150-120 mm

10 1 Flange ø 150

10a 1 Dumper ø 150mm

15 1 Air Outlet Connection

24 1 Junction box

25 2 Pipe clamps

Ref. Q.ty Installation Components

11 4 Wall Plugs ø 10

12c 6 Screws 2,9 x 6,5

12e 2 Screws 2,9 x 9,5

12f 4 Screws M6 x 10

12g 4 Screws M6 x 80

12h 4 Screws 5,2 x 70

21 1 Drilling template

22 4 6.4 mm int. dia washers

23 4 M6 nuts

Q.ty Documentation

1 Instruction Manual

12c

7.1a

7.1

22

23

12h

7.1b

2

2.1

2.2

12c

11

21

12g

1

12f

24

12e

15

12c

25

10

9

10a

EN

1

0

10

INSTALLATION

Drilling the Ceiling/shelf and fixing the frame

DRILLING THE CEILING/SHELF

• Use a plumb line to mark the centre of the hob on the ceiling/support shelf.

• Place the drilling template 21 provided on the ceiling/support shelf, making sure that the

template is in the correct position by lining up the axes of the template with those of the hob.

• Mark the centres of the holes in the template.

• Drill the holes at the points marked:

• For concrete ceilings, drill for plugs appropriate to the screw size.

• For hollow brick ceilings with wall thickness of 20 mm: drill ø 10 mm(immediately insert

the Dowels 11 supplied).

• For wooden beam ceilings, drill according to the wood screws used.

• For wooden shelf, drill ø 7 mm.

• For the power supply cable feed, drill ø 10 mm.

• For the air outlet (Ducted Version), drill according to the diameter of the external air ex-

haust duct connection.

• Insert two screws of the following type, crossing them and leaving 4-5 mm from the ceiling:

• For concrete ceilings, use the appropriate plugs for the screw size (not provided).

• for Cavity ceiling with inner space, with wall thickness of approx. 20 mm, Screws 12h,

supplied.

• For wooden beam ceilings, use 4 wood screws (not provided).

• For wooden shelf, use 4 screws 12g with washers 22 and nuts 23, provided.

EN

1

11

Fixing the frame

• Loosen the two screws fastening the lower chimney and re-

move this from the lower frame.

• Loosen the two screws fastening the upper chimney and re-

move this from the upper frame.

If you wish to adjust the height of the frame, proceed as follows:

• Unfasten the eight metric screws joining the two columns, lo-

cated at the sides of the frame.

• Adjust the frame to the height required, then replace all the

screws removed as above.

• Insert the upper chimney stack from above, and leave it run-

ning free on the frame.

• Lift up the frame, fit the frame slots onto the screws up to the

slot end positions.

• Tighten the two screws and fasten the other two screws pro-

vided with the hood.

Before tightening the screws completely it is possible to adjust

the frame by turning it. Make sure that the screws do not come

out of their seats in the slotted holes.

• The frame mountings must be secure to withstand the weight

of the hood and any stresses caused by the occasional side

thrust applied to the device.

On completion, check that the base is stable, even if the frame

is subjected to bending.

• In all cases where the ceiling is not strong enough at the sus-

pension point, the installer must provide strengthening using

suitable plates and backing pieces anchored to the structurally

sound parts.

2

1

EN

1

2

12

Connections

DUCTED VERSION AIR EXHAUST SYSTEM

When installing the ducted version, connect the hood to the

chimney using either a flexible or rigid pipe ø 150 or 120mm, the

choice of which is left to the installer.

To install a ø 150

• To install the dumper 10a.

• Fix the pipe in position using sufficient pipe clamps (not sup-

plied).

To install a ø 120

• To install a ø 120 mm air exhaust connection, insert the re-

ducer flange 9 on the dumper 10a.

• Fix the pipe in position using sufficient pipe clamps (not sup-

plied).

• Remove any activated charcoal filters.

ø 120

25

9

10a

ø 150

25

Recirculation version air outlet

• Fix the connection 15 to the frame using the 4 screws pro-

vided.

• Fix the flange 10 to the lower opening of the connection 15.

• Connect the hood air outlet to the flange in the lower part of

the junction using a rigid or flexible ø 150 tube (by installer’s

choice).

15

10

EN

1

3

13

Flue assembly - Mounting the hood body

• Position the upper chimney section and fix the upper part to the

frame using the 2 screws 12c (2,9 x 6,5) provided.

• Similarly, position the lower chimney section and fix the

lower part to the frame using the 2 screws 12c (2,9 x 6,5) pro-

vided.

Before fixing the hood body to the frame:

• Remove the grease filters from the hood body.

• Remove any activated charcoal filters.

• From below, use the 4 screws 12f (M6 x 10)provided to fix the

hood body to the frame.

12f

12c

ELECTRICAL CONNECTION

• Connect the hood to the mains through a two-pole switch hav-

ing a contact gap of at least 3 mm.

• Remove the grease filters (see paragraph Maintenance) being

sure that the connector of the feeding cable is correctly inserted

in the socket placed on the side of the fan.

• Connect the control connector Cmd.

• Connect the lights connector Lux.

• Place the connectors in the junction box 24 and close it using

the 2 screws 12e (2,9 x 9,5) provided.

• Fix the junction box to the hood body using the 2 screws 12c

(2,9 x 6,5) provided.

• For the recirculation version, fit the activated carbon odour fil-

ter.

• Replace the grease filters.

24

12e

Cmd

12c

Lux

EN

1

4

14

USE

L T1 T2 T3 T4 T5 F

The hood can be switched on pushing directly onto the requested speed without firstly hav-

ing to select 0/1 button .

Basic functions

Touch

control

Dual Function

Indicator lights

When briefly pressed it switches the lighting system

on and off.

Touch control unlit Lights off

Touch control lit Lights on

L

When pressed for 2 seconds it starts the lighting

system in “courtesy light” mode. The lamps are

fed at a reduced power of approximately 5W.

Such function can be stopped by pressing the

touch control for 2 seconds or just by pressing it

shortly in order to return to the normal lighting

mode. In courtesy light mode the touch control is

not lit.

Touch control unlit

Courtesy light on

Touch control lit Motor on

T1

When pressed the motor is stopped, regardless of the

speed it is set to.

Touch control unlit Motor off

T2

When pressed the motor is set to the first speed

Touch control lit

By a brief pressing the motor is set to the second

speed.

Touch control lit Second speed on

T3

By pressing the touch control for approximately 2

seconds the Delay function is enabled, i.e dela-

yed shutdown of the appliance ensuring a com-

plete elimination of the residual odours. This fun-

ction can be activated at OFF-position and at 1°,

2° and 3°speeds. It can be stopped in advance

by pressing any of the touch controls (T) with the

exception of T3. The Delay function works accor-

ding to the following scheme:

1°speed / OFF = 20 minuets

2°speed = 15 minutes

3°speed = 5 minutes

Flashing touch

control

Delay function on

T4

When pressed the motor is set to the third speed

Touch control lit

EN

1

5

15

Touch

control

Basic functions Indicator lights

T5

When pressed the motor is set to the intensive speed

timed to 5 minutes. At the end of 5 minutes of intensi-

ve speed the hood starts again at the speed it was set

to previously. In case the hood is set to the intensive

speed directly from OFF-state it will then start from

the first speed after 5 minutes of intensive speed.

Touch control lit

Metal grease filters satu-

ration alarm. Metal grease

filters need to be washed.

The alarm starts up after

100 working hours.

F

When pressed for 4 seconds it resets the filter alarm

signal indicated by flashing of the touch control T1.

This procedure can be carried out only when the

motor is stopped.

Flashing touch

control

Charcoal odour filter satu-

ration alarm. Charcoal

filter has to be replaced

and metal grease filters

washed. The alarm starts

up after 200 working

hours. (Activation; check

the paragraph “Odour

filter”)

EN

1

6

16

MAINTENANCE

REMOTE CONTROL (OPTIONAL)

The appliance can be controlled using a remote control powered

by a 1.5 V carbon-zinc alkaline batteries of the standard LR03-

AAA type.

• Do not place the remote control near to heat sources.

• Used batteries must be disposed of in the proper manner.

Grease filters

CLEANING OF THE METAL CASSETTE FILTERS

Alarm reset

• Stop the motor.

• Press the F -touch control for at least 4 seconds until the T1 -

touch control flashes.

Cleaning the filters

• Filters can be washed in the dish machine. They need to be

washed every 2 months or even more frequently in case of par-

ticularly intensive use of the hood.

• Remove the filters one by one pushing them towards the back

side of the unit and simultaneously pulling downwards.

• Any kind of bending of the filters has to be avoided when

washing them. Before fitting them again into the hood make

sure that they are completely dry.

• When fitting the filters into the hood pay attention that they are

mounted in correct position and that the handle faces outwards.

EN

1

7

17

Odour filter (Recirculation Version)

This filter cannot be washed or regenerated, and must be replaced when the F touch control starts

to flash, or at least once every 4 months. The alarm is only triggered when the motor is on.

Enabling/Disabling the alarm signal

• In Recirculation Version Hoods, the Filter saturation Alarm must be enabled at the time of

installation or later.

• Switch off the lights and the motor.

• Disconnect the mains power supply to the hood by removing the motor unit power supply

cable connector, switching off the power supply at the Mains or turning the Main switch off.

• Restore the connection, pressing and holding T2.

• Release the touch control, touch controls L, T2 and F will light up normally.

• Within 3 seconds press the touch control F until the key itself flashes to confirm as follows:

• 2 flashes – Charcoal odour Filter saturation Alarm ENABLED

• 1 flash - Charcoal odour Filter saturation Alarm DISABLED

REPLACING THE CHARCOAL ODOUR FILTER

Reset the alarm signal

• Stop the motor.

• Press the touch control F for at least 4 seconds, until the touch

control T1 flashes.

Replace the Filter

• Remove the metal grease filters.

• Remove the saturated charcoal filter, turning the fasteners pro-

vided.

• Fit the new filter and fasten it its correct position.

• Put the metal grease filters in their seats.

Lighting

LIGHT REPLACEMENT

20 W halogen light.

• Remove the 2 screws fixing the Lighting support, and pull it

out of from the Hood.

• Extract the lamp from the Support.

• Replace with another of the same type, making sure that the

two pins are properly inserted in the lamp holder socket holes.

• Replace the Support, fixing it in place with the two screws re-

moved as above.

FR

1

8

18

CONSEILS ET SUGGESTIONS

La présente notice d'emploi vaut pour plusieurs versions de l'appareil. Elle

peut contenir des descriptions d'accessoires ne figurant pas dans votre appa-

reil.

INSTALLATION

• Le fabricant décline toute responsabilité en cas de dommage dû à une installa-

tion non correcte ou non conforme aux règles de l’art.

• La distance minimale de sécurité entre le plan de cuisson et la hotte doit être

de 650 mm au moins.

• Vérifier que la tension du secteur correspond à la valeur qui figure sur la pla-

quette apposée à l’intérieur de la hotte.

• Pour les Appareils appartenant à la I

ère

Classe, veiller à ce que la

mise à la terre de l’installation électrique domestique ait été effectuée confor-

mément aux normes en vigueur.

• Connecter la hotte à la sortie d’air aspiré à l’aide d’une tuyauterie

d’un diamètre égal ou supérieur à 120 mm. Le parcours de la

tuyauterie doit être le plus court possible.

• Eviter de connecter la hotte à des conduites d’évacuation de fumées

issues d’une combustion tel que (Chaudière, cheminée, etc…).

• Si vous utilisez des appareils qui ne fonctionnent pas à l’électricité

dans la pièce ou est installée la hotte (par exemple: des appareils

fonctionnant au gaz), vous devez prévoir une aération suffisante du milieu. Si

la cuisine en est dépourvue, pratiquez une ouverture qui communique avec

l’extérieur pour garantir l’infiltration de l’air pur.

UTILISATION

• La hotte a été conçue exclusivement pour l’usage domestique, dans le but

d’éliminer les odeurs de la cuisine.

• Ne jamais utiliser abusivement la hotte.

• Ne pas laisser les flammes libres à forte intensité quand la hotte est en ser-

vice.

• Toujours régler les flammes de manière à éviter toute sortie latérale

de ces dernières par rapport au fond des marmites.

• Contrôler les friteuses lors de l’utilisation car l’huile surchauffée

pourrait s’enflammer.

• Ne pas préparer d’aliments flambés sous la hotte de cuisine : risque d’incendie

• Cet appareil ne doit pas être utilisé par des personnes (y compris les enfants)

ayant des capacités psychiques, sensorielles ou mentales réduites, ni par des

personnes n’ayant pas l’expérience et la connaissance de ce type d’appareils,

à moins d'être sous le contrôle et la formation de personnes responsables de

leur sécurité.

• Les enfants doivent être surveillés pour s'assurer qu'ils ne jouent pas avec

l'appareil.

ENTRETIEN

• Avant de procéder à toute opération d’entretien, retirer la hotte en retirant la

fiche ou en actionnant l’interrupteur général.

• Effectuer un entretien scrupuleux et en temps dû des Filtres, à la cadence

conseillée.

• Pour le nettoyage des surfaces de la hotte, il suffit d’utiliser un chiffon humide

et détersif liquide neutre.

650 mm min.

FR

1

9

19

CARACTERISTIQUES

Encombrement

650 min.

FR

2

0

20

Composants

Réf. Q.té Composants de Produit

1 1 Corps Hotte équipé de: Comandes, Lumière, Filtres

2 1 Cheminée Télescopique formée de :

2.1 1 Cheminée Supérieure

2.2 1 Cheminée Inférieure

7.1 1 Treillis télescopique avec Aspirateur, formé par:

7.1a 1 Treillis supérieur

7.1b 1 Treillis inférieur

9 1 Flasque de Réduction ø 150-120 mm

10 1 Flasque ø 150

10a 1 Buse avec clapet ø 150

15 1 Raccord Sortie Air

24 1 Boîte connexions

25 2 Colliers de serrage serre-tube

Réf. Q.té Composants pour l’installation

11 4 Chevilles ø 10

12c 6 Vis 2,9 x 6,5

12e 2 Vis 2,9 x 9,5

12f 4 Vis M6 x 10

12g 4 Vis M6 x 80

12h 4 Vis 5,2 x 70

21 1 Gabarit de perçage

22 4 Rondelles øi 6,4

23 4 Écrous M6

Q.té Documentation

1 Manuel d’instructions

12c

7.1a

7.1

22

23

12h

7.1b

2

2.1

2.2

12c

11

21

12g

1

12f

24

12e

15

12c

25

10

9

10a

La page est en cours de chargement...

Electrolux EFA90540X Manuel utilisateur

Electrolux EFA90540X Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents