Eaton Power Xpert Series Mode d'emploi

Eaton

®

Power Xpert

®

9395C UPS

1000kW/1000kVA, 1000kW/1100kVA or 1100kW/1100kVA

Installation and Operation Manual

Eaton

®

Power Xpert

®

9395C UPS

1000kW/1000kVA, 1000kW/1100kVA or 1100kW/1100kVA

Installation and Operation Manual

IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS

This manual contains important instructions that you should follow during installation and maintenance of the UPS

and batteries. Please read all instructions before operating the equipment and save this manual for future

reference.

CONSIGNES DE SÉCURITÉ IMPORTANTES CONSERVER CES INSTRUCTIONS

Ce manuel comporte des instructions importantes que vous êtes invité à suivre lors de toute procédure

d'installation et de maintenance des batteries et de l'onduleur. Veuillez consulter entièrement ces instructions

avant de faire fonctionner l'équipement et conserver ce manuel afin de pouvoir vous y reporter ultérieurement.

WARNING

This is a product for restricted sales distribution to informed partners (EN/IEC 62040-2). Installation restrictions or

additional measures may be needed to prevent electromagnetic disturbances.

AVERTISSEMENT!

Les ventes et la distribution de ce produit sont limitées aux partenaires avisés (EN/CEI 62040-2). Des restrictions

en matière d’installation ou des mesures supplémentaires sont parfois nécessaires pour éviter les perturbations

électromagnétiques.

Eaton and Power Xpert are registered trademarks and PredictPulse is a trademark of Eaton or its subsidiaries and affiliates. CA

Technologies is a registered trademark of CA, Inc. IBM and AS/400 are registered trademarks of International Business

Machines Corporation. Modbus is a registered trademark of Schneider Electric. National Electrical Code and NEC are registered

trademarks of National Fire Protection Association, Inc. All other trademarks are property of their respective companies.

the express written approval of Eaton.

TABLE OF CONTENTS

Eaton

®

Power Xpert

®

9395C UPS Installation and Operation Manual P-164000821—Rev 01 www.eaton.com/powerquality i

TABLE OF CONTENTS

1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

1.1 UPS Standard Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

1.1.1 Installation Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

1.1.2 Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

1.1.3 Customer Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

1.1.4 Advanced Battery Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

1.1.5 Power Management Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

1.2 Options and Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

1.2.1 Integrated Battery Cabinets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

1.2.2 Sync Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

1.2.3 Single-Feed Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

1.2.4 Continuous Static Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

1.2.5 Monitoring and Communication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

1.3 Battery System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

1.4 Using This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

1.5 Conventions Used in This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

1.6 Symbols, Controls, and Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

1.7 Getting Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

2 SAFETY WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

3 UPS INSTALLATION PLAN AND UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

3.1 Creating an Installation Plan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

3.2 Preparing the Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

3.2.1 Environmental Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

3.2.2 Installation Considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

3.2.3 UPS System Power Wiring Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

3.3 Inspecting and Unpacking the UPS Cabinets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16

4 INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

4.1 Preliminary Installation Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

4.2 Unloading the UPS Sections from the Pallet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

4.3 Mechanically Joining the Sections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7

4.4 Electrically Connecting the Sections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

4.5 Battery System Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16

4.6 Installing UPS External and Battery Power Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16

4.6.1 External Power Wiring Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16

4.6.2 Battery Power Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22

4.7 Installing Interface Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23

4.7.1 TB1, TB2, and TB3 Connections (Other than TB1 Battery Interface Connections) . . . . . . . . . . . . . . . 4-24

4.7.2 TB1 Battery Interface Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29

4.7.3 X-Slot Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-30

4.8 Installing a REPO Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-31

4.9 Installing Options, Accessories, and Distributed Bypass Control Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-34

4.10 Initial Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-34

4.11 Completing the Installation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-34

TABLE OF CONTENTS

ii Eaton

®

Power Xpert

®

9395C UPS Installation and Operation Manual

P-164000821—Rev 01 www.eaton.com/powerquality

5 INSTALLING OPTIONS AND ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

5.1 Installing an Optional Powerware Hot Sync CAN Bridge Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

5.2 Installing an Optional Remote Monitor Panel II. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4

5.3 Installing an Optional Relay Interface Module II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

5.4 Installing an Optional Supervisory Contact Module II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8

5.5 Accessory Mounting Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10

6 UNDERSTANDING UPS OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

6.1 UPS System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

6.2 Single UPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

6.2.1 Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

6.2.2 Online Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

6.2.3 Energy Saver System (ESS) Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3

6.2.4 Bypass Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4

6.2.5 Battery Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5

6.2.6 Maintenance Bypass Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6

6.2.7 Transfer to Maintenance Bypass and Load Bank Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6

6.2.8 Transfer to Maintenance Bypass and Load Bank Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7

6.3 Single UPS Unit System Oneline Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8

7 UPS OPERATING INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

7.1 UPS Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

7.1.1 Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

7.1.2 DC Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2

7.2 Color Touchscreen Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3

7.3 Using the Color Touchscreen Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4

7.3.1 Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5

7.3.2 Using the Touch Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5

7.3.3 Using the Main Menu Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7

7.3.4 Power Maps Screen (Online Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8

7.3.5 Power Maps Screen (Bypass Mode). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10

7.3.6 Command Confirmation Pop-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10

7.3.7 Meters Summary Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11

7.3.8 Input Meters Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12

7.3.9 Input Meters Detail Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14

7.3.10 Battery Meters Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-15

7.3.11 System Events Main Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-17

7.3.12 User Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-17

7.3.13 System Status Screen and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-19

7.3.14 Settings Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-21

7.3.15 Configuration Options Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-22

7.3.16 Energy Advantage Architecture (EAA) Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-22

7.3.17 Statistics Basic Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-24

7.3.18 ESS Comparison Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-25

7.3.19 UPS Module Map Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-25

7.3.20 System Overview Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-26

7.4 UPS Operation using the Color Touchscreen Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-27

7.4.1 Starting the UPS in Online Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-27

7.4.2 Using the Remote Emergency Power-off Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-28

TABLE OF CONTENTS

Eaton

®

Power Xpert

®

9395C UPS Installation and Operation Manual P-164000821—Rev 01 www.eaton.com/powerquality iii

8 COMMUNICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

8.1 X-Slot Cards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

8.2 PredictPulse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2

8.2.1 PredictPulse Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2

8.2.2 Installing PredictPulse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2

8.3 Power Management Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3

8.4 Building Alarm Monitoring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3

8.5 General Purpose Relay Contact. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3

8.6 Remote Monitor Panel II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4

8.7 Relay Interface Module II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6

8.8 Supervisory Contact Module II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7

9 UPS MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

9.1 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

9.2 Performing Preventive Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2

9.2.1 DAILY Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2

9.2.2 MONTHLY Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2

9.2.3 PERIODIC Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5

9.2.4 ANNUAL Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5

9.2.5 BATTERY Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5

9.3 Installing Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6

9.4 Recycling the Used Battery or UPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6

9.5 Maintenance Training . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7

10 PRODUCT SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1

10.1 Model Numbers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1

10.2 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1

10.2.1 UPS Input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1

10.2.2 UPS Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2

10.2.3 UPS Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2

10.2.4 Battery RunTime Ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2

WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . W-1

TABLE OF CONTENTS

iv Eaton

®

Power Xpert

®

9395C UPS Installation and Operation Manual P-164000821—Rev 01 www.eaton.com/powerquality

This page intentionally left blank.

LIST OF FIGURES

Eaton

®

Power Xpert

®

9395C UPS Installation and Operation Manual P-164000821—Rev 01 www.eaton.com/powerquality v

LIST OF FIGURES

Figure 1-1. Eaton 9395C-1100 UPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Figure 3-1. UPS Cabinet Dimensions – (Front View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Figure 3-2. UPS Cabinet Dimensions (Right Side View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Figure 3-3. ISBM Section Dimensions (Front View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Figure 3-4. ISBM Section Dimensions (Top View). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Figure 3-5. ISBM Section Dimensions (Bottom View). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Figure 3-6. PM Section Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Figure 3-7. PM Dimensions – (Top View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

Figure 3-8. UPS Center of Gravity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

Figure 3-9. Remote EPO Switch Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

Figure 3-10. UPS Cabinet as Shipped on Pallet (ISBM Section) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19

Figure 3-11. UPS Cabinet as Shipped on Pallet (PM Section) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20

Figure 4-1. Removing the ISBM Section Left Side Shipping Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

Figure 4-2. Removing the ISBM Section Right Side Shipping Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

Figure 4-3. Removing the PM Section Left Side Shipping Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

Figure 4-4. Removing the PM Section Right Side Shipping Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

Figure 4-5. Section Joining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7

Figure 4-6. ISBM and PM Sections Joined . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Figure 4-7. ISBM Section to PM Section Joining Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

Figure 4-8. ISBM Section Intercabinet Power Terminal Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12

Figure 4-9. ISBM Section Output Power to PM Terminal Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13

Figure 4-10. UPS Intercabinet Interface Harness Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14

Figure 4-11. Pl1 Interface Board Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15

Figure 4-12. J39 Location on Pl1 Interface Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15

Figure 4-13. ISBM and PM Section Debris Shields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17

Figure 4-14. ISBM and PM Section Conduit and Wire Entry Locations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18

Figure 4-15. ISBM Section Power Terminal Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20

Figure 4-16. ISBM Section Power Terminal Detail AA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21

Figure 4-17. ISBM Section Power Terminal Detail BB – Common Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23

Figure 4-18. ISBM Section Interface Terminal Locations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25

Figure 4-19. Interface Terminal Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27

Figure 4-20. Typical Alarm Relay Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27

Figure 4-21. Terminal Blocks TB1, TB2, and TB3 Connector Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-28

Figure 4-22. Typical Battery Interface Connection – Common Battery System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29

Figure 4-23. X-Slot Communication Bays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-30

Figure 4-24. REPO Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-31

Figure 4-25. Normally-Open REPO Switch Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-32

Figure 4-26. Normally-Closed REPO Switch Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-33

Figure 4-27. Normally-Closed and Normally-Open REPO Switch Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-33

Figure 5-1. Powerware Hot Sync CAN Bridge Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Figure 5-2. Hot Sync CAN Bridge Card Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

Figure 5-3. Remote Monitor Panel II and Relay Interface Module II Terminal Locations . . . . . . . . . . . . . . . . . . . . . . . . 5-5

Figure 5-4. Remote Monitor Panel II, Relay Interface Module II, or Supervisory Contact Module II Wiring . . . . . . . . . . 5-5

Figure 5-5. J1, J2, J3, and J4 15-Pin D-Sub Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7

Figure 5-6. Supervisory Contact Module II Terminal Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8

Figure 5-7. Supervisory Contact Module II TB2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9

LIST OF FIGURES

vi Eaton

®

Power Xpert

®

9395C UPS Installation and Operation Manual

P-164000821—Rev 01 www.eaton.com/powerquality

Figure 5-8. Remote Monitor Panel II Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10

Figure 5-9. Relay Interface Module II Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11

Figure 5-10. Supervisory Contact Module II Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12

Figure 6-1. Main Elements of the UPS System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

Figure 6-2. Path of Current Through the UPS in Online Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3

Figure 6-3. Path of Current Through the UPS in Bypass Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5

Figure 6-4. Path of Current Through the UPS in Battery Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5

Figure 6-5. One PM, Common Rectifier Feed, Common Battery, Dual-Feed Configuration. . . . . . . . . . . . . . . . . . . . . . 6-9

Figure 6-6. Simplified Dual-Feed UPS with Maintenance Bypass Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10

Figure 7-1. UPS Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

Figure 7-2. Remote Shunt Trip Switch - Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2

Figure 7-3. UPS Color Touchscreen Control Panel (Typical) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3

Figure 7-4. UPS Color Touchscreen Control Panel (Typical) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4

Figure 7-5. Parts of the Touch Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5

Figure 7-6. Sign In or Password Request Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6

Figure 7-7. Home Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7

Figure 7-8. Main Menu and Power Maps Screen (Online Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8

Figure 7-9. Output kVA Screen from Home Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8

Figure 7-10. Average Efficiency Screen from Home Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9

Figure 7-11. Consumption Screen from Home Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9

Figure 7-12. Bypass Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10

Figure 7-13. Typical Command Confirmation Screen (Charger Off) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10

Figure 7-14. Meters Summary Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11

Figure 7-15. Input Meters Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12

Figure 7-16. Bypass Meters Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12

Figure 7-17. Output Meters Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-13

Figure 7-18. Input Meters Detail Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14

Figure 7-19. Select Source Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14

Figure 7-20. Battery Meters Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-15

Figure 7-21. Battery Log Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-15

Figure 7-22. Battery Log Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-16

Figure 7-23. Battery Log Summary Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-16

Figure 7-24. System Events Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-17

Figure 7-25. User Log Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-18

Figure 7-26. User Log Detail Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-18

Figure 7-27. System Status Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-19

Figure 7-28. Module Controls Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-19

Figure 7-29. Module Control Detail Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-20

Figure 7-30. Online Mode Metering Method Option Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-20

Figure 7-31. Bypass Mode Metering Method Option Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-21

Figure 7-32. Settings Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-21

Figure 7-33. Configuration Options Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-22

Figure 7-34. Energy Advantage Architecture (EAA) Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-22

Figure 7-35. Disable ESS Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-23

Figure 7-36. High Alert Timer Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-23

Figure 7-37. Statistics Basic Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-24

Figure 7-38. Statistics Data Detail Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-24

Figure 7-39. ESS Comparison Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-25

LIST OF FIGURES

Eaton

®

Power Xpert

®

9395C UPS Installation and Operation Manual P-164000821—Rev 01 www.eaton.com/powerquality vii

Figure 7-40. UPS Module Map Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-25

Figure 7-41. System Overview Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-26

Figure 7-42. REPO Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-29

Figure 8-1. Optional X-Slot Cards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

Figure 8-2. Remote Monitor Panel II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4

Figure 8-3. Relay Interface Module II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6

Figure 8-4. Supervisory Contact Module II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7

Figure 9-1. ISBM Section Air Filter Locations - Continuous Static Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4

Figure 9-2. PM Section Air Filter Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5

LIST OF FIGURES

viii Eaton

®

Power Xpert

®

9395C UPS Installation and Operation Manual P-164000821—Rev 01 www.eaton.com/powerquality

This page intentionally left blank.

Eaton

®

Power Xpert

®

9395C UPS Installation and Operation Manual P-164000821—Rev 01 www.eaton.com/powerquality 1-1

Chapter 1 Introduction

The Eaton

®

Power Xpert

®

9395C uninterruptible power supply (UPS) is a true online, continuous-duty,

transformerless, double-conversion, solid-state, three-phase system, providing conditioned and uninterruptible

AC power to protect the customer's load from power failures.

The Power Xpert 9395C contains a section configured as an integrated system bypass module (ISBM) rated for

a maximum of 1100 kVA.

The Eaton 9395C online power protection system is used to prevent loss of valuable electronic information,

minimize equipment downtime, and minimize the adverse effect on production equipment due to unexpected

power problems.

The Eaton 9395C UPS continually monitors incoming electrical power and removes the surges, spikes, sags,

and other irregularities that are inherent in commercial utility power. Working with a building's electrical

system, the UPS system supplies clean, consistent power that sensitive electronic equipment requires for

reliable operation. During brownouts, blackouts, and other power interruptions, batteries provide emergency

power to safeguard operation.

The UPS is housed in a free-standing cabinet, divided into two sections to facilitate shipping:

l

Integrated System Bypass Module (ISBM)

l

Power Module (PM)

The sections match in style and color and have safety shields behind the door and front panels for hazardous

voltage protection.

The Eaton 9395C UPS configuration is shown in Figure 1-1.

NOTE Startup and operational checks must be performed by an authorized Eaton

Customer Service Engineer, or the warranty terms specified on page W-1 become

void. This service is offered as part of the sales contract for the UPS system.

Contact an Eaton service representative in advance (usually a two-week notice is

required) to reserve a preferred startup date

Introduction

1-2 Eaton

®

Power Xpert

®

9395C UPS Installation and Operation Manual P-164000821—Rev 01 www.eaton.com/powerquality

Figure 1-1. Eaton 9395C-1100 UPS

1.1 UPS Standard Features

The UPS has many standard features that provide cost-effective and consistently reliable power protection. The

descriptions in this section provide a brief overview of the UPS standard features.

1.1.1 Installation Features

Each UPS section is shipped separately. The sections are mechanically and electrically joined at the installation

site, and can be permanently bolted to the floor.

Power wiring can be routed through the top or bottom of the cabinet with connections made to easily

accessible terminals. Control wiring is routed through the top of the cabinet and must be installed in accordance

with Class 1 wiring methods.

1.1.2 Control Panel

The control panel, located on the front of the UPS is a 7-inch color touchscreen to control the operation of the

UPS and to display the status of the UPS system. See Chapter 7, “UPS Operating Instructions” for additional

information.

1.1.3 Customer Interface

l

Building Alarm Monitoring. Up to five inputs in the UPS are available to connect the facility's alarm system

contacts. Some system configurations may limit the number of inputs available. The UPS uses these inputs

to monitor the building alarms in addition to the UPS status. See Chapter 8, “Communication” for additional

information.

PM SECTIONISBM SECTION

Introduction

Eaton

®

Power Xpert

®

9395C UPS Installation and Operation Manual P-164000821—Rev 01 www.eaton.com/powerquality 1-3

l

Alarm Contact. One alarm contact is provided for connection to equipment at the facility, such as a light, an

audible alarm, or a computer terminal. The equipment connected to this contact alerts you to a UPS alarm.

See Chapter 8, “Communication” for additional information.

l

X-Slot

®

Communication Bays. Four communication bays are standard equipment. One to four optional X-Slot

®

connectivity cards can be installed in the UPS module at any time. X-Slot cards are quickly installed at the

front of the UPS and are hot-pluggable. See Chapter 8, “Communication” for additional information.

1.1.4 Advanced Battery Management

A three-stage charging system increases battery service life by optimizing recharge time, and protects batteries

from damage due to high current charging and inverter ripple currents. Charging at high currents can overheat

and damage batteries.

1.1.5 Power Management Software

Eaton’s Intelligent Power

®

Software solution, based on Web2.0 technology, includes two applications:

Intelligent Power

®

Manager™ for UPS management and monitoring, and Intelligent Power

®

Protector™, which

allows graceful shutdown of operating systems. See Chapter 8, “Communication” for additional information.

1.2 Options and Accessories

Contact an Eaton sales representative for information about the following options.

1.2.1 Integrated Battery Cabinets

Battery backup protection can be provided by equipping the UPS system with Eaton 9395C battery cabinets

containing sealed lead-acid, maintenance-free batteries. The cabinets are designed for standalone installation

and may be installed adjacent to the UPS or in a separate location. The recommended installation location for

adjacent battery cabinets is on the right side of the UPS cabinet to allow for future expansion using an external

module.

Consult the Eaton

®

Power Xpert

®

9395C Integrated Battery Cabinet (Models 1085 and 1085HR) Installation

Manual (TBD) for specifics on battery cabinet usage with the 9395C.

1.2.2 Sync Control

An optional Eaton 9395C Sync Control maintains the critical load outputs of two separate single module 9395C

UPS systems in synchronization. This option facilitates the uninterrupted transfer of the load from one load bus

to another by means of transfer switches. The Sync Control is housed in a wall-mounted panel that can be

located between the UPS units for easy wiring.

1.2.3 Single-Feed Kit

An optional kit is available for converting the dual-feed rectifier and bypass inputs to a single-feed configuration.

The kit consists of jumpers and bus bar extensions for each phase, and the hardware required for installation.

1.2.4 Continuous Static Switch

A continuous static switch is used to provide transfer of the load from the inverter to the bypass source in the

event the inverter become unavailable.

1.2.5 Monitoring and Communication

The UPS system can be further enhanced by adding optional accessories such as a Remote Emergency

Power-off (REPO) control, RMP II, SCM II, RIM II, or X-Slot communication cards. See Chapter 5, “Installing

Options and Accessories” for additional information.

l

Remote Monitor Panel II (RMP II) – An optional RMP II contains backlit status indicators and a local horn,

allowing monitoring of the operational status and alarm condition of the UPS from virtually any location

within the facility.

Introduction

1-4 Eaton

®

Power Xpert

®

9395C UPS Installation and Operation Manual P-164000821—Rev 01 www.eaton.com/powerquality

l

Relay Interface Module II (RIM II) – An optional RIM II uses relay contact closures to indicate the UPS

operating status and alarm condition.

l

Supervisory Contact Module II (SCM II) – An optional SCM II establishes an interface between the UPS

system equipment and the customer's monitor.

l

X-Slot Cards – Optional X-Slot cards support several protocols, such as SNMP, HTTP, IBM AS/400, and

Modbus.

l

PredictPulse

™

Remote Monitoring and Management Service – PredictPulse is a subscription monitoring and

management service from Eaton that collects and analyzes data from connected power infrastructure

devices, providing us with the insight needed to make recommendations and take action on your behalf. It’s

also powered by CA Technologies, bringing together the best in hardware and software. Like a second set of

eyes on your power infrastructure, PredictPulse provides 24/7 remote monitoring of alarms and system

performance (load, temperature/humidity, battery health, energy savings and service level) to reduce

downtime risk and expedite repairs. PredictPulse also shares real-time status and trend information via an

online dashboard and smartphone mobile app (Apple and Android), giving subscribers insights about past

and current performance, a list of all active alarms, and asset management data (i.e., battery date codes, last

and next scheduled service dates, firmware versions). The service notifies customers of critical alarms,

supports remote diagnostics, and facilitates smart dispatch of technicians. PredictPulse requires a Power

Xpert® Gateway Card (PXGX) connectivity card in an X-Slot communication bay and an Environmental

Monitoring Probe (EMP) for battery temperature/humidity monitoring.

See Chapter 8, “Communication” for additional information on monitoring and communication features.

1.3 Battery System

Although not provided with the UPS, a battery system is required to provide emergency short-term backup

power to safeguard operation during brownouts, blackouts, and other power interruptions. The battery system

should be equipped with lead-acid batteries. An external battery disconnect switch must be used.

UPSs in distributed bypass and parallel systems must use a separate battery system.

See the battery related documents located in the system manual for battery cabinet specifics.

1.4 Using This Manual

This manual describes how to install and operate the Eaton 9395C UPS. Read and understand the procedures

described in this manual to ensure trouble-free installation and operation. In particular, be thoroughly familiar

with the REPO procedure (see paragraph 7.4.2).

The information in this manual is divided into sections and chapters. The system, options, and accessories

being installed dictate which parts of this manual should be read. At a minimum, Chapters 1 through 4 and

Chapter 7 should be examined.

Read through each procedure before beginning the procedure. Perform only those procedures that apply to the

UPS system being installed or operated.

Introduction

Eaton

®

Power Xpert

®

9395C UPS Installation and Operation Manual P-164000821—Rev 01 www.eaton.com/powerquality 1-5

1.5 Conventions Used in This Manual

This manual uses these type conventions:

l

Bold type highlights important concepts in discussions, key terms in procedures, and menu options, or

represents a command or option that you type or enter at a prompt.

l

Italic type highlights notes and new terms where they are defined.

l

Screen type represents information that appears on the screen or LCD.

In this manual, the term UPS refers only to the UPS cabinet and its internal elements. The term UPS system

refers to the entire power protection system – the UPS cabinet, the battery system, and options or accessories

installed.

1.6 Symbols, Controls, and Indicators

The following are examples of symbols used on the UPS or accessories to alert you to important information:

Icon Description

Information notes call attention to important features or instructions.

[Keys] Brackets are used when referring to a specific key, such as [Enter] or [Ctrl].

RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk

of electric shock symbol.

CAUTION: REFER TO OPERATOR'S MANUAL - Refer to your operator's

manual for additional information, such as important operating and

maintenance instructions.

This symbol indicates that you should not discard the UPS or the UPS

batteries in the trash. This product contains sealed, lead-acid batteries and

must be disposed of properly. For more information, contact your local

recycling/reuse or hazardous waste center.

This symbol indicates that you should not discard waste electrical or

electronic equipment (WEEE) in the trash. For proper disposal, contact your

local recycling/reuse or hazardous waste center.

Introduction

1-6 Eaton

®

Power Xpert

®

9395C UPS Installation and Operation Manual P-164000821—Rev 01 www.eaton.com/powerquality

1.7 Getting Help

If help is needed with any of the following:

l

Scheduling initial startup

l

Regional locations and telephone numbers

l

A question about any of the information in this manual

l

A question this manual does not answer

Please call the Customer Reliability Center at:

United States: 1-800-843-9433 or 1-919-870-3028

Canada: 1-800-461-9166 ext 260

All other countries: Call your local service representative

Please use the following e-mail address for manual comments, suggestions, or to report an error in this manual:

[email protected]

Eaton

®

Power Xpert

®

9395C UPS Installation and Operation Manual P-164000821—Rev 01 www.eaton.com/powerquality 2-1

Chapter 2 Safety Warnings

IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS

This manual contains important instructions that should be followed during installation and

maintenance of the UPS and batteries. Read all instructions before operating the equipment and

save this manual for future reference.

The UPS is designed for industrial or computer room applications, and contains safety shields

behind the door and front panels. However, the UPS is a sophisticated power system and should

be handled with appropriate care.

DANGER

This UPS contains LETHAL VOLTAGES. All repairs and service should be performed by AUTHORIZED

SERVICE PERSONNEL ONLY. There are NO USER SERVICEABLE PARTS inside the UPS.

DANGER!

Cet onduleur peut générer des TENSIONS MORTELLES. L’installation et l’entretien ne doivent être

effectués que par le PERSONNEL AUTORISÉ. Ne contient AUCUNE PIÈCE REMPLAÇABLE.

WARNING

l

The UPS is powered by its own energy source (batteries). The output terminals may carry live

voltage even when the UPS is disconnected from an AC source.

l

To reduce the risk of fire or electric shock, install this UPS in a temperature and humidity

controlled, indoor environment, free of conductive contaminants. Ambient temperature must

not exceed 40°C (104°F). Do not operate near water or excessive humidity (95% maximum).

The system is not intended for outdoor use.

l

Ensure all power is disconnected before performing installation or service.

l

Batteries can present a risk of electrical shock or burn from high short.circuit current. The

following precautions should be observed: 1) Remove watches, rings, or other metal objects; 2)

Use tools with insulated handles; 3) Do not lay tools or metal parts on top of batteries; 4) Wear

rubber gloves and boots.

l

ELECTRIC ENERGY HAZARD. Do not attempt to alter any UPS or battery wiring or connectors.

Attempting to alter wiring can cause injury.

l

As a result of the connected loads high leakage current is possible. Connection to earth ground

is required for safety and proper product operation. Do not check UPS operation by any action

that includes removal of the earth (ground) connection with loads attached.

l

Do not open or mutilate batteries. Released electrolyte is harmful to the skin and eyes. It may

be toxic.

Safety Warnings

2-2 Eaton

®

Power Xpert

®

9395C UPS Installation and Operation Manual

P-164000821—Rev 01 www.eaton.com/powerquality

AVERTISSEMENT!

l

L’onduleur est alimenté par sa propre source d’énergie (batteries). Les bornes de sortie peuvent

être sous tension, même lorsque l’onduleur est débranché d’une source de courant alternatif.

l

Pour réduire les risques d’incendie et de decharge électrique, installer l’onduleur à l’intérieur,

dans un endroit exempt d’éléments conducteurs et où la température et l’humidité sont

régulées. La température ambiante ne doit pas dépasser 40°C (104°F). Ne pas faire fonctionner

près d’une source d’eau ou dans un endroit très humide (95% maximum). Le système n’est pas

conçu pour une utilisation extérieure.

l

Toutes les sources d’alimentation doivent être débranchées avant de procéder à l’installation et

à l’entretien.

l

Les batteries peuvent présenter un risque de décharge électrique ou de brûlure en raison du

courant de court-circuit élevé. Les précautions de base suivantes doivent être suivies: 1) retirer

les montres, bagues et autres objets métalliques; 2) utiliser des outils munis d’une poignée

isolée; 3) ne pas déposer les outils ou des pièces de métal sur les batteries; 4) porter des gants

et des bottes en caoutchouc.

l

DANGERS ÉLECTRIQUES. Ne pas tenter de modifier le câblage et les connecteurs de

l’onduleur ou des batteries. Toute tentative de modification peut provoquer des blessures.

l

Les charges raccordées pourraient provoquer un courant de fuite élevé. La mise à la terre est

donc obligatoire pour garantir la sécurité et le bon fonctionnement du produit. Lors de la

vérification du fonctionnement de l’UPS, ne pas enlever la mise à la terre si des charges y sont

raccordées.

l

Ne pas ouvrir ni abîmer les batteries. L’électrolyte qu’elles contiennent est dangereux pour la

peau et les yeux. Il peut être toxique.

CAUTION

l

Installation or servicing should be performed by qualified service personnel knowledgeable of

UPS and battery systems, and required precautions. Keep unauthorized personnel away from

equipment. Consider all warnings, cautions, and notes before installing or servicing equipment.

DO NOT DISCONNECT the batteries while the UPS is in Battery mode.

l

Replace batteries with the same number and type of batteries as originally installed with the

UPS.

l

Disconnect the charging source prior to connecting or disconnecting terminals.

l

Determine if the battery is inadvertently grounded. If it is, remove the source of the ground.

Contacting any part of a grounded battery can cause a risk of electric shock. An electric shock is

less likely if you disconnect the grounding connection before you work on the batteries.

l

Proper disposal of batteries is required. Refer to local codes for disposal requirements.

l

Do not dispose of batteries in a fire. Batteries may explode when exposed to flame.

l

Keep the UPS door closed and front panels installed to ensure proper cooling airflow and to

protect personnel from dangerous voltages inside the unit.

l

Do not install or operate the UPS system close to gas or electric heat sources.

l

The operating environment should be maintained within the parameters stated in this manual.

l

Keep surroundings uncluttered, clean, and free from excess moisture.

l

Observe all DANGER, CAUTION, and WARNING notices affixed to the inside and outside of the

equipment.

La page charge ...

Eaton Power Xpert Series Mode d'emploi

Ce manuel convient également à

Eaton Power Xpert Series Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents