Yard-Man YM25 Manuel utilisateur

Marque: Yard-Man

Modèle: YM25

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Operator’s Manual

IMPORTANT: Read safety rules and instructions carefully before operating equipment.

PRINTED IN U.S.A.

PART NO. 769-00570 (12/02)

English

Curved Shaft,

2-Cycle Trimmer

Model

YM25

TABLE OF CONTENTS

Content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page

Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Know Your Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Oil and Fuel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Starting/Stopping Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Maintenance and Repair Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Cleaning and Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Inside Back Cover

FINDING MODEL NUMBER

This Operator’s Manual is an important part of your new trimmer. It will help you assemble, prepare and maintain the

unit for best performance. Please read and understand what it says.

Before you start assembling your new equipment, please locate the model plate on the unit and

copy the information from it onto the space provided below. The information on the model plate is very

important if you need help from our Customer Support Department or an authorized dealer.

• The model number is located on the engine. A sample model plate is shown and explained below. For future

reference, please copy the model number and the serial number of the equipment in the space provided.

CALLING CUST

OMER SUPPOR

If you have difficulty assembling this product or have any questions regarding the controls, operation or maintenance of

this unit, please call the Customer Support Department.

Call 1- (800)-345-8746, or 1- (800)-668-1238 in Canada, to reach a Customer Support representative.

Please have your unit’s model number and serial number ready when you call. You will be asked to

enter the serial number in order to process your call. This information is explained above.

VISIT OUR

WEB SITE

Visit our web site at www.yardman.com for more information about our quality Yard Man products, customer service,

parts, tips, literature and more.

Copy the model and parent

part number here:

Copy the serial number here:

S/N :

ITEM :

MODEL :

SPARK ARRESTOR

NOTE: For users on U.S. Forest Land and in the states

of California, Maine, Oregon and Washington. All U.S.

Forest Land and the state of California (Public Resources

Codes 4442 and 4443), Oregon and Washington require, by

law that certain internal combustion engines operated on

forest brush and/or grass-covered areas be equipped with

a spark arrestor, maintained in effective working order, or

the engine be constructed, equipped and maintained for the

prevention of fire. Check with your state or local authorities

for regulations pertaining to these requirements. Failure to

follow these requirements could subject you to liability or a

fine. This unit is factory equipped with a spark arrestor.

If it requires replacement, ask your LOCAL SERVICE

DEALER to install the accessory part #182747 Spark

Arrestor.

The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols and

their explanations deserve your careful attention and understanding. The safety warnings do not by

themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper

accident prevention measures.

SAFETY ALERT SYMBOL: Indicates danger, warning, or caution. Attention is required in order to avoid

serious personal injury. May be used in conjunction with other symbols or pictographs.

NOTE: Advises you of information or instructions vital to the operation or maintenance of the equipment.

DANGER: Failure to obey a safety warning will result in serious injury to yourself or to others. Always

follow the safety precautions to reduce the risk of fire, electric shock and personal injury.

WARNING: Failure to obey a safety warning can result in injury to yourself and others. Always follow

the safety precautions to reduce the risk of fire, electric shock and personal injury.

CAUTION: Failure to obey a safety warning may result in property damage or personal injury to

yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and

personal injury.

READ ALL INSTRUCTIONS

WARNING: When using the unit, you must

follow the safety rules. For your own safety

and that of bystanders, please read these

instructions before operating the unit.

Please keep the instructions for later use.

Before Operating

• Read the instructions carefully. Be familiar with the

controls and proper use of the unit.

• Do not operate this unit when tired, ill or under the

influence of alcohol, drugs or medication.

WARNING

CALIFORNIA PROPOSITION 65

WARNING

THE ENGINE EXHAUST FROM THIS

PRODUCT CONTAINS CHEMICALS

KNOWN TO THE STATE OF CALIFORNIA

TO CAUSE CANCER, BIRTH DEFECTS

OR OTHER REPRODUCTIVE HARM.

• Children under the age of 15 must not use the unit;

teens may operate the unit with adult guidance.

• Inspect the unit before use. Replace damaged parts.

Check for fuel leaks. Make sure all fasteners are in

place and secure. Replace cutting attachment parts

that are cracked, chipped or damaged in any way.

Make sure the cutting attachment is properly installed

and securely fastened. Be sure that the cutting

attachment shield is properly attached, and positioned

as recommended. Failure to do so can result in

personal injury to the operator and bystanders, as well

as damage to the unit.

• Use only 0.080-inch (2.03 mm) diameter Genuine

Factory Parts™ replacement line. Never use metal-

reinforced line, wire, chain or rope. These can break

off and become dangerous projectiles.

WARNING!

Read the Operator’s Manual and follow all warnings and safety instructions. Failure to do so can

result in serious injury to the operator and/or bystanders.

FOR QUESTIONS, CALL 1-800-345-8746 IN U.S. OR 1-800-668-1238 in CANADA

SECTION 1: IMPORTANT SAFE OPERATION PRACTICES

SECTION 1a:RULES FOR SAFE OPERATION

• Be aware of risk of injury to the head, hands and feet.

• Clear the area to be cut before each use. Remove

rocks, broken glass, nails, wire, string and other

objects which may be thrown or become entangled in

the cutting attachment. Clear the area of children,

bystanders and pets; keep them outside a 50-foot

(15 m.) radius, at a minimum. Even then, they are still

at risk from thrown objects. Encourage bystanders to

wear eye protection. If you are approached, stop the

unit immediately.

• Squeeze the throttle control and check that it returns

automatically to the idle position. Make all adjustments

or repairs before using the unit.

• This unit was not designed to be used as a

brushcutter. Do not attach or operate this unit with any

type of brushcutting blade or brushcutting attachment.

Safety Warnings for Gas Trimmers

WARNING: Gasoline is highly flammable,

and its vapors can explode if ignited. Take

the following precautions:

• Store fuel only in containers specifically designed and

approved for the storage of such materials.

• Always stop the engine and allow it to cool before

filling the fuel tank. Never remove the fuel tank cap or

add fuel when the engine is hot. Never operate the unit

without the fuel cap securely in place. Loosen the fuel

tank cap slowly to relieve any pressure in the tank.

• Add fuel in a clean, well-ventilated outdoor area where

there are no sparks or flames. Remove the fuel cap

slowly, and only after the engine stops. Do not smoke

while fueling or mixing fuel. Wipe up any spilled fuel

from the unit immediately.

• Avoid creating a source of ignition for spilled fuel. Do

not start the engine until fuel vapors dissipate.

• Move the unit at least 30 feet (9.1 m) from the fueling

source and site before starting the engine. Do not

smoke. Keep sparks and open flames away from the

area while adding fuel or operating the unit.

While Operating

• Never start or run the unit inside a closed room or

building. Breathing exhaust fumes can be fatal.

Operate this unit only in a well-ventilated outdoor area.

• Wear safety glasses or goggles that meet ANSI Z87.1

standards and are marked as such. Wear ear/hearing

protection when operating this unit. Wear a face or

dust mask if the operation is dusty.

• Wear heavy long pants, boots, gloves and a long

sleeve shirt. Do not wear loose clothing, jewelry, short

pants, sandals or go barefoot. Secure hair above

shoulder level.

• The cutting attachment shield must always be in place

while operating the unit. Do not operate unit without

both trimming lines extended, and the proper line

installed. Do not extend the trimming line beyond the

length of the shield.

• This unit has a clutch. The cutting attachment remains

stationary when the engine is idling. If it does not, have

the unit adjusted by an authorized service technician.

• Adjust the D-handle to your size in order to provide the

best grip.

• Be sure the cutting attachment is not in contact with

anything before starting the unit.

• Use the unit only in daylight or good artificial light.

• Avoid accidental starting. Remain in the starting

position whenever pulling the starter rope. The

operator and unit must be in a stable position while

starting. Refer to Starting/Stopping Instructions.

• Use the right tool. Only use this tool for its intended

purpose.

• Do not overreach. Always keep proper footing and

balance.

• Always hold the unit with both hands when operating.

Keep a firm grip on both handles or grips.

• Keep hands, face, and feet at a distance from all

moving parts. Do not touch or try to stop the cutting

attachment when it rotates.

• Do not touch the engine, gear housing or muffler.

These parts get extremely hot from operation, even

after the unit is turned off.

• Do not operate the engine faster than the speed

needed to cut, trim or edge. Do not run the engine at

high speed when not cutting.

• Always stop the engine when cutting is delayed or

when walking from one cutting location to another.

• If you strike or become entangled with a foreign

object, stop the engine immediately and check for

damage. Do not operate before repairing damage. Do

not operate the unit with loose or damaged parts.

• Stop the unit, switch the engine to off, and disconnect

the spark plug for maintenance or repair.

• Use only Genuine Factory Parts™ replacement parts

and accessories for this unit. These are available from

your authorized service dealer. Use of any unauthorized

parts or accessories could lead to serious injury to the

user, damage to the unit, and a voided warranty.

• Keep unit clean of vegetation and other materials.

They may become lodged between the cutting

attachment and shield.

• To reduce fire hazard, replace a faulty muffler and

spark arrestor. Keep the engine and muffler free from

grass, leaves, excessive grease or carbon build up.

Other Safety Warnings

• Never store a fueled unit inside a building where fumes

may reach an open flame or spark.

• Allow the engine to cool before storing or transporting.

Be sure to secure the unit while transporting.

•Store the unit in a dry area, locked up or up high to prevent

unauthorized use or damage, out of the reach of children.

• Never douse or squirt the unit with water or any other

liquid. Keep handles dry, clean and free from debris. Clean

after each use, see Cleaning and Storage instructions.

• Keep these instructions. Refer to them often and use

them to instruct other users. If you loan someone this

unit, also loan them these instructions.

SAVE THESE INSTRUCTIONS

SYMBOL MEANING

• SAFETY ALERT SYMBOL

Indicates danger, warning or caution.

May be used in conjunction with other

symbols or pictographs.

•WARNING - READ

OPERATOR'S MANUAL

Read the operator’s manual(s) and follow

all warnings and safety instructions.

Failure to do so can result in serious injury

to the operator and/or bystanders.

• WEAR EYE AND HEARING

PROTECTION

WARNING:

Thrown objects and loud

noise can cause severe eye injury and

hearing loss. Wear eye protection

meeting ANSI Z87.1 standards and ear

protection when operating this unit.

Use a full face shield when needed.

• KEEP BYSTANDERS AWAY

WARNING:

Keep all bystanders,

especially children and pets, at least

50 feet (15 m) from the operating area.

• UNLEADED FUEL

Always use clean, fresh unleaded fuel.

• OIL

Refer to operator's manual for the

proper type of oil.

SYMBOL MEANING

• THROWN OBJECTS AND

ROTATING CUTTER CAN

CAUSE SEVERE INJURY

WARNING:

Do not operate without

the cutting attachment shield in place.

Keep away from the rotating cutting

attachment.

•ON/OFF STOP CONTROL

ON / START / RUN

•ON/OFF STOP CONTROL

OFF or STOP

• HOT SURFACE WARNING

Do not touch a hot muffler, gear housing

or cylinder. You may get burned. These

parts get extremely hot from operation.

They remain hot for a short time after the

unit is turned off.

• SHARP BLADE

WARNING:

Sharp blade on cutting

attachment shield. To prevent serious

injury, do not touch line cutting blade.

This operator's manual describes safety and international symbols and pictographs that may appear on this product.

Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.

SECTION 1b:SAFETY & INTERNATIONAL SYMBOLS

SECTION 2: KNOW YOUR UNIT

Applications

As a trimmer:

• Cutting grass and light weeds

• Edging

• Decorative trimming around trees, fences, etc.

Other optional accessories may be used with the YM25.

Refer to Operating the EZ-Link System for a list of add-ons.

Cutting Attachment

Shield

Fuel Cap

Throttle

Control

D-Handle

Cutting Attachment

Shaft Grip

Primer Bulb

EZ-Start

Lever

Air Filter/Muffler

Cover

Engine Stand

Spark Plug

Shaft Housing

Starter Rope Grip

EZ-Link™

Line Cutting Blade

Spark Plug

Muffler

Muffler Guard

On/Off Stop Control

Shoulder Strap Clip

Muffler

EZ-Start™ Lever

SECTION 3: ASSEMBLY INSTRUCTIONS

On some units, the J-handle may be pre-installed. In this

case you must loosen screws and adjust the handle to fit

the operator. Go to step 4 if the J-handle is pre-installed.

Install and Adjust the D-handle

1. Remove the screws and bottom clamp piece that

were installed on the D-handle for shipping.

2. Place D-handle the over the shaft housing and onto

the bottom clamp. See Figure 1. Place it a minimum

of 6 inches (15.24 cm) from the end of the shaft grip.

3. Start screws with a large Flat-head or T-25 Torx

screwdriver. Do not tighten until you make the handle

adjustment.

4. If it was pre-installed, loosen the screws on the

D-handle just enough to move the D-handle.

5. While holding the unit in the operating position,

position the D-handle to the location that provides

you the best grip. See Figure 2.

6. Tighten the clamp screws evenly, until the D-handle

is secure.

Installing the Cutting Attachment Shield

Use the following instructions if the cutting attachment

shield on your unit is not installed or if you ever need to

re-install it.

WARNING: To prevent serious personal

injury, never operate the trimmer without

the cutting attachment shield in place.

1. Place the cutting attachment shield onto the shaft

housing above the clamp assembly. See Figure 3.

2. Push the cutting attachment shield down to the top of

the cutting attachment assembly and then rotate the

cutting attachment shield until the screw holes align and

the guard fits into the recessed pocket. See Figure 4

3. Install the four (4) screws with a Phillips screwdriver.

See Figure 5.

Figure 4

Figure 2

(4) Screws

Shaft

Housing

D-Handle

Bottom Clamp

Shaft Grip

Minimum 6 inches

(15.24 cm)

On/Off Stop Control

Figure 1

Shaft Housing

(4) Screws

Clamp

Assembly

Cutting

Attachment

Assembly

Cutting Attachment

Shield

Recessed

Pocket

Figure 3

Figure 5

SECTION 4: OIL AND FUEL INFORMATION

WARNING: Gasoline is extremely

flammable. Ignited vapors may explode.

Always stop the engine and allow it to cool

before filling the fuel tank. Do not smoke

while filling the tank. Keep sparks and

open flames at a distance from the area.

WARNING: Remove fuel cap slowly to avoid

injury from fuel spray. Never operate the unit

without the fuel cap securely in place.

WARNING: Add fuel in a clean, well-

ventilated outdoor area. Wipe up any

spilled fuel immediately. Avoid creating a

source of ignition for spilled fuel. Do not

start the engine until fuel vapors dissipate.

NOTE: Dispose of the old fuel/oil mix in accordance to

Federal, State and Local regulations.

Oil and Fuel Mixing Instructions

Old and/or improperly mixed fuel is the main reason for

improper unit performance. Be sure to use fresh, clean

unleaded fuel. Follow the instructions carefully for the

proper fuel/oil mixture.

Definition of Blended Fuels

Today's fuels are often a blend of gasoline and

oxygenates such as ethanol, methanol, or MTBE (ether).

Alcohol-blended fuel absorbs water. As little as 1%

water in the fuel can make fuel and oil separate. It forms

acids when stored. When using alcohol-blended fuel,

use fresh fuel (less than 60 days old).

Using Blended Fuels

If you choose to use a blended fuel, or its use is

unavoidable, follow recommended precautions:

• Always use fresh fuel mix per your operator's manual

• Always agitate the fuel mix before fueling the unit

• Drain the tank and run the engine dry before storing

the unit

Using Fuel Additives

The bottle of 2-cycle oil that came with your unit

contains a fuel additive which will help inhibit corrosion

and minimize the formation of gum deposits. It is

recommended that you use only our 2-cycle oil with this

unit.

If unavailable, use a good 2-cycle oil designed for air-

cooled engines along with a fuel additive, such as

STA-BIL

Gas Stabilizer or an equivalent. Add 0.8 oz.

(23 ml.) of fuel additive per gallon of fuel according to the

instructions on the container. NEVER add fuel additives

directly to the unit's fuel tank.

CAUTION: For proper engine operation and

maximum reliability, pay strict attention to

the oil and fuel mixing instructions on the

2-cycle oil container. Using improperly mixed

fuel can severely damage the engine.

Thoroughly mix the proper ratio of 2-cycle engine oil with

unleaded gasoline in a separate fuel can. Use a 40:1 fuel/oil

ratio. Do not mix them directly in the engine fuel tank. See

the table below for specific gas and oil mixing ratios.

NOTE: One gallon (3.8 liters) of unleaded gasoline mixed

with one 3.2 oz. (95 ml.) bottle of 2-cycle oil

makes a 40:1 fuel/oil ratio.

UNLEADED GAS 2-CYCLE OIL

1 US. GALLON + 3.2 FL. OZ.

(3.8 LITERS) (95 ml)

1 LITER + 25 ml

MIXING RATIO - 40:1

SECTION 5: STARTING/STOPPING INSTRUCTIONS

Starting Instructions

WARNING: Operate this unit only in a well-

ventilated outdoor area. Carbon monoxide

exhaust fumes can be lethal in a confined area

WARNING: Avoid accidental starting. Make

sure you are in the starting position when

pulling the starter rope. See Figure 8. To

avoid serious injury, the operator and unit

must be in a stable position while starting.

To avoid serious personal injury, ensure any

Add-On being used is installed correctly

and secure before starting unit.

1. Mix gas with oil. Fill fuel tank with fuel/oil mixture.

See Oil and Fuel Mixing Instructions.

2. Make sure the On/Off Stop Control is in the ON (I)

position. See Figure 6.

3. Fully press and release the primer bulb 10 times,

slowly, until FUEL IS VISIBLE IN THE PRIMER

BULB. See Figure 7. If you can’t see fuel in the bulb,

press and release the bulb as many times as it takes

before you can see fuel in it.

4. Push the EZ-Start™ Lever to the left until it clicks and

locks into place. See Figure 7.

5. With the unit in the starting position, DO NOT

SQUEEZE THE THROTTLE CONTROL. See Figure 8.

Pull the starter rope 5 times briskly, making sure the

EZ-Start™ lever is pushed to the left. If the engine

starts to run before the fifth pull, proceed to step 6. If

the engine does not start, go back to step 3.

NOTE: When starting, the EZ-Start™ Lever will

automatically click off when you squeeze the

throttle control.

NOTE: If the outside temperature or engine temperature

exceeds 90º F and the engine fails to start after 5

pulls, fully squeeze the throttle control and pull

the starter rope briskly 3 to 8 more times. The

engine should start within these pulls.

6. When the engine starts, squeeze the throttle control

to warm up the engine for 5 to 10 seconds. The EZ-

Start™ Lever will click off automatically. See Figure 7.

NOTE: if the engine stalls before you squeeze the

throttle control, hold the throttle control and pull

the starter rope until the trimmer starts.

NOTE: If the engine stalls while squeezing the throttle,

go back to step 4.

NOTE: To start a warm engine, begin at step 4.

On/Off Stop Control

Start/On (I)

Stop/Off (O)

Primer Bulb

Starter Rope

Throttle Control

EZ-Start™

Lever

Throttle Control

Figure 6

Figure 7

Figure 8

Stopping Instructions

1. Release your hand from the throttle control. See

Figure 8. Allow the engine to cool down by idling.

2. Push and hold the On/Off Stop Control in the OFF (O)

position until the engine stops running. See Figure 6

For edging (when using the line head cutting attachment

with EZ-Link™ models), lock the release button of the

cutting attachment into the 90° edging hole or the 180°

edging hole. See Figure 11.

Operating the EZ-Link™ System

The EZ-Link™ system enables the use of these optional

Add-Ons:

Blower/Vacuum . . . . . . . . . . . . . . . . . . . . . . . . . . BV720r

Cultivator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GC720r

Edger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LE720r

Hedge Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . HS720r

Snow Thrower . . . . . . . . . . . . . . . . . . . . . . . . . . . ST720r

Straight Shaft Trimmer . . . . . . . . . . . . . . . . . . . . SS725r

Tree Pruner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TP720r

Turbo Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . TB720r

Removing the Cutting Attachment or Add-Ons

1. Turn the knob counterclockwise to loosen. See Figure 9.

2. Press and hold the release button. See Figure 9.

3. While firmly holding the upper shaft housing, pull

the cutting attachment or add-on straight out of the

EZ-Link™ coupler. See Figure 10.

Installing the Cutting Attachment or Add-On

NOTE: Place the unit on the ground or on a work bench

to make add-on installation or removal easier.

1. Turn knob counterclockwise to loosen.

EZ-Link™ Coupler

Release Button

Guide Recess

Knob

Primary Hole

Upper Shaft Housing

EZ-Link™ Coupler

2. While firmly holding the add-on, push it straight into

the EZ-Link™ coupler. See Figure 10.

NOTE: Aligning the release button with the guide recess

will help installation. See Figure 9.

3. Turn the knob clockwise to tighten. See Figure 11.

Knob

Lower Shaft Housing

Release Button

90˚ Edging Hole

(Trimmer Only)

180˚ Edging Hole

(Trimmer Only)

CAUTION: Lock the release button in the

primary hole and securely tighten the knob

before operating this unit

SECTION 6: OPERATING INSTRUCTIONS

Figure 11

Figure 10

Figure 9

CAUTION:

The cutting attachment and add-

ons with the EZ-Link™ system are to be used

in the primary hole unless stated otherwise in

the specific add-ons operator’s manual.

Using the wrong hole could lead to personal

injury or damage to the unit.

WARNING: Read and understand the

operator’s manual for each add-on prior to

operation.

WARNING: To avoid serious personal injury

and damage to the unit, shut off the unit

before removing or installing add-ons.

Holding the Trimmer

WARNING: Always wear eye, hearing, foot

and body protection to reduce the risk of

injury when operating this unit.

Before operating the unit, stand in the operating

position. See Figure 12. Check for the following:

• The operator is wearing eye protection and proper

clothing

• With a slightly-bent right arm, the operator’s right hand

is holding the shaft grip

• The operator’s left arm is straight, the left hand holding

the D-handle

• The unit is at waist level

•

The cutting attachment is parallel to the ground and

easily contacts the grass without the need to bend ove

Adjusting Trimming Line Length

The Bump Head™ cutting attachment allows you to release

trimming line without stopping the engine. To release more

line, lightly tap the cutting attachment on the ground while

operating the trimmer at high speed. See Figure 13.

NOTE: Always keep the trimming line fully extended.

Line release becomes more difficult when the

cutting line gets shorter.

Each time the head is bumped, about 1 inch (25.4 mm)

of trimming line releases. A blade in the cutting

attachment shield will cut the line to the proper length if

any excess line is released.

For best results, tap the bump knob on bare ground or

hard soil. If you attempt a line release in tall grass, the

engine may stall. Always keep the trimming line fully

extended. Line release becomes more difficult when the

cutting line gets shorter.

NOTE: Do not rest the bump knob on the ground while

the unit is running.

CAUTION: Do not remove or alter the line

cutting blade assembly. Excessive line

length may make the unit overheat.

Some line breakage will occur from:

• Entanglement with foreign matter

• Normal line fatigue

• An attempt to cut thick, stalky weeds

•

Forcing the line into objects such as walls or fence posts

Tips for Best Trimming Results

• For best trimming results, operate unit at full throttle.

• Keep the cutting attachment parallel to the ground.

• Do not force the cutting attachment. Allow the tip of

the line to do the cutting, especially along walls.

Cutting with more than the tip will reduce cutting

efficiency and may overload the engine.

• Cut grass over 8 inches (200 mm) tall by working

from top to bottom in small increments to avoid

premature line wear or engine drag.

• Cut from right to left whenever possible. Cutting to

the left improves the unit's cutting efficiency.

Clippings are thrown away from the operator.

• Slowly move the trimmer into and out of the cutting

area at the desired height. Move either in a forward-

to-backward or side-to-side motion. Cutting shorter

lengths produces the best results.

• Trim only when grass and weeds are dry.

• The life of your cutting line is dependent upon:

• Following the trimming techniques

• What vegetation is being cut

• Where vegetation is cut

For example, the line will wear faster when trimming

against a foundation wall as opposed to trimming

around a tree.

Decorative Trimming

Decorative trimming refers to the removal of vegetation

around trees, posts, fences and more.

Rotate the whole unit so that the cutting attachment is at

a 30° angle to the ground. See Figure 14.

SECTION 6: OPERATING INSTRUCTIONS

Figure 12

Figure 13

Figure 14

SECTION 7: MAINTENANCE AND REPAIR INSTRUCTIONS

WARNING: To prevent serious injury, never

perform maintenance or repairs with unit

running. Always service and repair a cool

unit. Disconnect the spark plug wire to

ensure that the unit cannot start.

Maintenance Schedule

Perform these required maintenance procedures at the

frequency stated in the table. These procedures should

also be a part of any seasonal tune-up.

NOTE: Some maintenance procedures may require

special tools or skills. If you are unsure about

these procedures take your unit to any non-road

engine repair establishment, individual or

authorized service dealer.

NOTE: Maintenance, replacement, or repair of the

emission control devices and system may be

performed by any non-road engine repair

establishment, individual or authorized service

dealer.

In order to assure peak performance of your engine,

inspection of the engine exhaust port may be necessary

after 50 hours of operation. If you notice lost RPM, poor

performance or general lack of acceleration, this service

may be required. If you feel your engine is in need of this

inspection, refer service to any non-road engine repair

establishment, individual or authorized service dealer for

repair. DO NOT attempt to perform this process yourself

as engine damage may result from contaminants

involved in the cleaning process for the port.

FREQUENCY MAINTENANCE REQUIRED REFER TO

Before starting engine Fill fuel tank with fresh fuel Page 8

Every 10 hours Clean and re-oil air filter Page 15

Every 25 hours

Check and clean spark arrestor

Check spark plug condition and gap

Page 16

Page 18

Every 50 hours

Inspect exhaust port and spark arrestor screen for clogging or

obstruction to assure maximum performance levels

Page 16

Line Installation

Always use Genuine Factory Parts™ 0.080 in. (2.03 mm)

replacement line. Using line other than the specified may

make the engine overheat or fail.

WARNING: Never use metal-reinforced line,

wire, chain or rope. These can break off

and become dangerous projectiles.

There are two methods to replace the trimming line:

• Wind the inner reel with new line

• Install a pre-wound inner reel

Winding the Inner Reel with New Line

NOTE: It is unnecessary to remove the bump knob to

install new trimming line.

1. Cut two pieces of 0.080 inch (2.03 mm) trimming line,

10 feet (3 m) long.

2. Hold the outer spool and turn the inner reel

counterclockwise to line up the arrows on the outer

spool and inner reel. See Figure 15.

Figure 15

WARNING: Always use the correct line

length when installing trimming line on the

unit. The line may not release properly if

the line is too long.

Top View Of The SpeedSpool

Outer Spool

Inner Reel

Bump Knob

Arrows

SECTION 7: MAINTENANCE AND REPAIR INSTRUCTIONS

Line Locking Hole

Trimming Line

Line Loading Hole

Eyelet

5. Insert the line into the locking hole. Do not push the

line more than a 1/2 inch (12.7 mm) into the line

locking hole. The line will form a small loop when it is

inserted correctly. See Figure 17.

3. Pull old line out of the line loading and line locking

holes. See Figure 16 and 17.

4. Insert a piece of trimming line straight into one of the

two eyelets in the outer spool. Push it up through the

line loading hole in the inner reel. See Figure 16. Do

not bend the line when inserting it into the eyelet.

6. Pull the line from the outer spool until the line is tight

against the inner reel. See Figure 18.

Installing a Pre-wound Reel

1. Turn the bump knob counterclockwise and remove

the bump knob, spring and foam seal. See Figure 21.

9. If winding the line becomes difficult or if the line

jams, pull the ends of the line from the spool. See

Figure 20. Continue winding the inner reel

counterclockwise.

7. Repeat procedures 4-6 with the second piece of line.

8. Hold the outer spool. Wind the inner reel

counterclockwise until approximately four (4) inches

(102 mm) of line remain. See Figure 19.

NOTE: Do not wind the inner reel before installing the

second piece of line.

Bump Knob

Foam Seal

Spring

Inner Reel

Figure 21

Figure 20

Figure 19

Figure 18

Figure 17

Figure 16

SECTION 7: MAINTENANCE AND REPAIR INSTRUCTIONS

SpeedSpool

Replacement Parts

Refer to the Accessories/Replacement Parts section.

4. Hold the inner reel in place and install the bump

knob, spring and foam seal. Press down and turn the

bump knob clockwise. Grasp the ends and pull

firmly to release the line from the holding slots in the

inner reel. See Figure 21.

Releasing the Inner Reel

If the SpeedSpool

does not release line correctly, pull

the ends of the line firmly from the spool. See Figure 20.

If this does not the release line, follow the Cleaning the

SpeedSpool

instructions.

2. Pull the old inner reel with existing line from the outer

spool.

3. Insert the ends of the prewound inner reel line into

the outer spool eyelets. See Figure 22. Push the new

inner reel, arrow side up, into the outer spool.

4. Remove any existing line from the inner reel before

cleaning. Remove any debris or grass from the knob,

spring, inner reel and foam seal. Wash the inner reel

with warm soapy water. See Figure 24.

Cleaning the SpeedSpool

may be necessary if:

•A jammed or excessive line must be removed

• The SpeedSpool

becomes difficult to wind or does

not operate correctly when bumping the head on the

ground

1. Hold the outer spool, and unscrew the bump knob

counterclockwise. See Figure 23.

2. Pull out the bump knob, spring and foam seal.

Shaft

Plunger

NOTE: The inner reel must be totally dry before

reinstalling it into the outer spool. Do not

lubricate the inner reel or outer spool assembly.

6. Place the inner reel into the outer spool.

7. Place the bump knob, spring and foam seal into the

inner reel. See Figure 21.

8. Press the bump knob down and tighten clockwise.

9. Install new line as described in Line Installation for

the SpeedSpool

5. Clean the shaft and the inner surface of the outer

spool. To clean the shaft underneath the plunger,

press down on the plunger. See Figure 25. Remove

any dirt or debris from the shaft.

Inner Reel

3. Pull the inner reel with existing line from the outer

spool. See Figure 22.

Figure 24

Figure 23

Figure 22

Figure 25

Air Filter Maintenance

Removing the Air Filter/Muffler Cover

WARNING: To avoid serious personal injury,

always turn your trimmer off and allow it to

cool before you clean or service it.

1. Remove the four (4) screws securing the air filter/

muffler cover. See Figure 26. Use a flat blade or T20

Torx bit screwdriver.

2. Pull the cover from the engine. Do not force.

Cleaning the Air Filter

WARNING: To avoid serious personal injury,

always turn your trimmer off and allow it to

cool before you clean it or perform any

maintenance.

Clean and re-oil the air filter every 10 hours of operation.

It is an important item to maintain. Failure to maintain the

air filter will VOID the warranty.

1. Remove air filter/muffler cover. See Removing the Air

Filter/Muffler Cover.

SECTION 7: MAINTENANCE AND REPAIR INSTRUCTIONS

Figure 26

Air Filter

Inside Muffler

Cover

Figure 28Figure 27

Screws

EZ-Start™

Lever

Figure 30

Figure 29

2. Turn cover over and look inside to locate the air filter.

Remove the air filter from inside the air filter/muffler

cover. See Figure 27.

3. Wash the filter in detergent and water. See Figure

28. Rinse the filter thoroughly. Squeeze out excess

water. Allow it to dry completely.

4. Apply enough clean SAE 30 oil to lightly coat the

filter. See Figure 29.

5. Squeeze the filter to spread and remove excess oil.

See Figure 30.

Muffler - Front Side

Muffler - Back Side

Bolts

Exhaust

Gasket

Spark

Arrestor

Muffler - Back Side

Spark

Arrestor

Flat blade

Screwdriver

Spark Arrestor

6. Replace the air filter inside the air filter/muffler cover.

See Figure 27.

NOTE:

Operating the unit without the air filter and air

filter/muffler cover assembly, will VOID the warranty.

Reinstalling the Air Filter/Muffler Cover

1. Place the air filter/muffler cover over the back of the

carburetor and muffler. Align the screw holes.

2. Insert the four (4) screws into the holes in the air

filter/muffler cover and tighten. See Figure 26.

Do not over tighten.

Spark Arrestor Maintenance

1. Remove air filter/muffler cover. See Removing the Air

Filter/Muffler Cover.

2. Locate muffler front and the two (2) bolts securing it

to the engine. See Figure 31. Remove the two (2)

bolts using a flatblade screwdriver or 5/16-inch

socket or nut driver. Pull muffler off of the engine.

3. Turn muffler over to the back side and locate the

exhaust gasket. Remove the muffler gasket from the

muffler. See Figure 31.

NOTE: If the exhaust gasket is torn or damaged, replace

it with a new gasket before reassembling muffler.

Using a small flatblade screwdriver, carefully pry up the

spark arrestor from the recessed hole. See Figure 32.

Remove the spark arrestor from the muffler.

5. Clean the spark arrestor with a wire brush. Replace it

if it is damaged or if it is impossible to clean

thoroughly. See Figure 32.

6. Reinstall the spark arrestor by pressing it into the

recessed hole on the muffler's back side. Make sure

it fits tightly against the muffler and is not raised up.

7. Place the exhaust gasket against muffler's back side.

Align the gasket bolt holes with the bolt holes in the

muffler. While holding exhaust gasket in place, insert

the bolts into the muffler's front side. See Figure 31.

8. Place the muffler (with the exhaust gasket in place

and bolts inserted), against the engine, aligning the

bolt holes. Tighten the bolts to secure the muffler to

the engine. If using a torque wrench torque to:

80-90 in.•lb. (9-10.2 N•m).

WARNING: If the muffler is not tightened

securely, it could fall off causing damage to

the unit and possible serious personal injury.

9. Reinstall the air filter/muffler cover.

SECTION 7: MAINTENANCE AND REPAIR INSTRUCTIONS

Figure 32

Figure 31

Idle Speed Screw

Figure 33

SECTION 7: MAINTENANCE AND REPAIR INSTRUCTIONS

Carburetor Adjustment

The idle speed of the engine is adjustable through the air

filter/muffler cover. See Figure 33.

NOTE: Careless adjustments can seriously damage your

unit. An authorized service dealer should make

carburetor adjustments.

Check Fuel Mixture

Old and/or improperly mixed fuel is usually the reason for

improper unit performance. Drain and refill the tank with

fresh, properly mixed fuel prior to making any

adjustments. Refer to Oil and Fuel Information.

Clean Air Filter

The condition of the air filter is important to the operation

of the unit. A dirty air filter will restrict air flow and change

the air/fuel mixture. This is often mistaken for an out of

adjustment carburetor. Check the condition of the air

filter before adjusting the idle speed screw. Refer to Air

Filter Maintenance.

Adjust Idle Speed

WARNING: The cutting attachment may

spin during idle speed adjustments. Wear

protective clothing and observe all safety

instructions to prevent serious personal

injury.

If, after checking the fuel mixture and cleaning the air

filter, the engine still will not idle, adjust the idle speed as

follows.

1. Start the engine and let it run at a high idle for a

minute to warm up. See Starting/Stopping

Instructions.

2. Release the throttle trigger and let the engine idle. If

the engine stops, insert a small Phillips or flat blade

screwdriver into the hole in the air filter/muffler cover.

See Figure 33. Turn the idle speed screw in,

clockwise, 1/8 of a turn at a time (as needed) until the

engine idles smoothly.

NOTE: The cutting attachment should not rotate when

the engine idles.

3. If the cutting attachment rotates when the engine idles,

turn the idle speed screw counterclockwise 1/8 of a

turn at a time (as needed), to reduce idle speed.

Checking the fuel mixture, cleaning the air filter, and

adjusting the idle speed should solve most engine

problems.

If this is not the case and the following are all true:

• The engine will not idle

• The engine hesitates or stalls on acceleration

• There is a loss of engine power

Have the carburetor adjusted by an authorized service

dealer.

WARNING: After turning the unit off, make

sure the cutting attachment has stopped

before setting the unit down. This helps

prevent serious personal injury.

SECTION 7: MAINTENANCE AND REPAIR INSTRUCTIONS

Replacing the Spark Plug

Use a Champion RDJ7Y spark plug (or equivalent). The

correct air gap is 0.020 inch (0.5 mm). Remove the plug

after every 25 hours of operation and check its condition.

1. Stop the engine and allow it to cool. Grasp the plug

wire firmly and pull it from the spark plug.

2. Clean around the spark plug. Remove the spark plug

from the cylinder head by turning a 5/8 in. socket

counterclockwise.

3. Replace cracked, fouled or dirty spark plug. Set the

air gap at 0.020 in. (0.5 mm) using a feeler gauge.

See Figure 34.

CAUTION: Do not sand blast, scrape or

clean electrodes. Grit in the engine could

damage the cylinder.

4. Install a correctly-gapped spark plug in the cylinder

head. Tighten by turning the 5/8 inch socket

clockwise until snug.

If using a torque wrench torque to:

110-120 in.•lb. (12.3-13.5 N•m).

Do not over tighten.

Accessories/Replacement Parts

2-Cycle Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147543

Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 610311

Spark Arrestor . . . . . . . . . . . . . . . . . . . . . . . . . . . .182747

Replacement Line . . . . . . . . . . . . . . . . . . . . . . . . 181472

Replacement Line Cartridge . . . . . . . . . . . . . . . . 181460

Inner Reel Spring . . . . . . . . . . . . . . . . . . . . . . . . . 181465

Outer Spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181457

Inner Reel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181464

Bump Knob™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181468

Fuel Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180000

Shoulder Strap . . . . . . . . . . . . . . . . . . . . . . . . . . . 682075

These replacement parts can be purchased from your

local authorized dealer.

0.020 in.

(0.5 mm)

Long Term Storage

If the unit will be stored for an extended time, use the

following storage procedure:

1. Drain all fuel from the fuel tank into a container with

the same 2-cycle fuel mixture. Do not use fuel that

has been stored for more than 60 days. Dispose of

the old fuel/oil mix in accordance to Federal, State,

and Local regulations.

2. Start the engine and allow it to run until it stalls. This

ensures that all fuel has been drained from the

carburetor.

3. Allow the engine to cool. Remove the spark plug and

put 1 oz. (30 ml) of any high quality motor oil or 2-

cycle oil into the cylinder. Pull the starter rope slowly

to distribute the oil. Reinstall the spark plug.

NOTE: Remove the spark plug and drain all of the oil

from the cylinder before attempting to start the

trimmer after storage.

4. Thoroughly clean the unit and inspect for any loose

or damaged parts. Repair or replace damaged parts

and tighten loose screws, nuts or bolts. The unit is

ready for storage.

Transporting

• Allow the engine to cool before transporting.

• Secure the unit while transporting.

• Drain fuel from unit.

• Tighten fuel cap before transporting.

Cleaning

WARNING: To avoid serious personal injury,

always turn your trimmer off and allow it to

cool before you clean or service it.

Use a small brush to clean off the outside of the unit. Do

not use strong detergents. Household cleaners that

contain aromatic oils such as pine and lemon, and

solvents such as kerosene, can damage plastic housing

or handle. Wipe off any moisture with a soft cloth.

Storage

• Never store the unit with fuel in the tank where fumes

may reach an open flame or spark.

• Allow the engine to cool before storing.

• Store the unit locked up to prevent unauthorized use

or damage.

• Store the unit in a dry, well-ventilated area.

• Store the unit out of the reach of children.

Figure 34

SECTION 8: TROUBLESHOOTING GUIDE

If further assistance is required, contact your authorized service dealer

Trouble Possible Cause(s) Corrective Action

ENGINE WILL

NOT START

• Empty fuel tank

• Primer bulb wasn’t pressed enough

• Engine is flooded

• Old or improperly mixed fuel

• Fouled spark plug

• Plugged spark arrestor

• EZ-Start lever was not set

• Fill fuel tank with properly-mixed fuel

• Press primer bulb fully and slowly 10 times

• Hold throttle control and pull starter rope until it starts

• Drain gas tank and add fresh fuel mixture

• Replace or clean spark plug

• Clean or replace the spark arrestor

• Move lever to start

ENGINE WILL

NOT IDLE

• Air filter is plugged

• Old or improperly mixed fuel

• Improper carburetor adjustment

• Replace or clean the air filter

• Drain gas tank and add fresh fuel mixture

• Adjust according to the Carburetor Adjustment section

ENGINE WILL

NOT

ACCELERATE

• Old or improperly mixed fuel

• Improper carburetor adjustment

• Cutting attachment bound with grass

• Dirty air filter

• Plugged spark arrestor

• Drain gas tank and add fresh fuel mixture

• Take to an authorized service dealer for adjustment

• Stop the engine and clean the cutting attachment

• Clean or replace the air filter

• Clean or replace spark arrestor

ENGINE

LACKS

POWER OR

STALLS WHEN

CUTTING

• Old or improperly mixed fuel

• Improper carburetor adjustment

• Fouled spark plug

• Plugged spark arrestor

• Drain gas tank and add fresh fuel mixture

• Take to an authorized service dealer for adjustment

• Replace or clean spark plug

• Clean or replace the spark arrestor

CUTTING

ATTACHMENT

WILL NOT

ADVANCE LINE

• Cutting attachment bound with grass

• Cutting attachment out of line

• Inner reel bound up

• Cutting head is dirty

• Line welded

• Line twisted when refilled

• Not enough line is exposed

• Stop the engine and clean cutting attachment

• Refill with new line

• Replace the inner reel

• Clean inner reel and outer spool

• Disassemble, remove the welded section and rewind

• Disassemble and rewind the line

• Push the bump knob and pull out line until 4 inches

(102 mm) of line is outside of the cutting attachment

CUTTING LINE

ADVANCES

WILDLY

• Oil is in the cutting head • Clean the cutting head attachment

SECTION 9: SPECIFICATIONS

Engine*

Drive Shaft and Cutting Attachment*

*All specifications are based on the latest product information available at the time of printing. We reserve the right to

make changes at any time without notice.

Engine Type........................................................................................................................................... Air-Cooled, 2-Cycle

Stroke................................................................................................................................................... 1.25 in. (31.75 mm.)

Displacement............................................................................................................................................. 1.9 cu in. (31 cc.)

Operating RPM................................................................................................................................................... 7,200+ rpm

Idle Speed RPM ....................................................................................................................................... 2,800 - 4,400 rpm

Ignition Type.......................................................................................................................................................... Electronic

Ignition Switch............................................................................................................................................... Rocker Switch

Spark Plug Gap...................................................................................................................................... 0.020 in. (0.5 mm.)

Lubrication................................................................................................................................................... Fuel/Oil Mixture

Fuel/Oil Ratio.................................................................................................................................................................. 40:1

Carburetor....................................................................................................................................... Diaphragm, All-Position

Starter............................................................................................................................................................... Auto Rewind

Muffler..................................................................................................................................................... Baffled with Guard

Throttle............................................................................................................................................... Manual Spring Return

Fuel Tank Capacity.................................................................................................................................... 13.5 oz. (400 ml.)

Drive Shaft Housing ............................................................................................................................................ Steel Tube

Throttle Control ........................................................................................................................................ Finger-Tip Trigger

Approximate Unit Weight (No fuel, with string cutting head, string guard and D-handle)............................. 13 lbs. (6 kg.)

Cutting Mechanism................................................................................................ SpeedSpool

Dual String Cutting Head

Shoulder Strap ........................................................................................................................................................ Optional

Line Spool Diameter.................................................................................................................................... 3 in. (76.2 mm.)

Trimming Line Diameter........................................................................................................................ 0.080 in. (2.03 mm.)

Cutting Path Diameter............................................................................................................................... 17 in. (43.18 cm.)

La page est en cours de chargement...