MTD YM90BC Manuel utilisateur

Marque: MTD

Modèle: YM90BC

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Ce manuel convient également à

Yard-Man YM90BC

Operator’s Manual

Starting

2-Cycle Gasoline Trimmer/

Brushcutter

YM90BC

SAVE THESE INSTRUCTIONS

For service call 1-800-800-7310 in the United States, or

1-800-668-1238 in Canada to obtain a list of authorized service

dealers near you. For more details about your unit, visit our

website at www.yardman.com.

DO NOT RETURN THE UNIT TO THE RETAILER. PROOF OF

PURCHASE WILL BE REQUIRED FOR WARRANTY

SERVICE.

THIS PRODUCT IS COVERED BY ONE OR MORE U.S.

PATENTS. OTHER PATENTS PENDING.

Service on this unit both within and after the warranty period

should be performed only by an authorized and approved

service dealer.

All information, illustrations, and specifications in this manual

are based on the latest product information available at the

time of printing. We reserve the right to make changes at any

time without notice.

WARNING: When using the unit, you must follow

the safety rules. Please read these instructions

before operating the unit in order to ensure the

safety of the operator and any bystanders. Please

keep these instructions for later use.

SPARK ARRESTOR NOTE

NOTE: For users on U.S. Forest Land and in the states of

California, Maine, Oregon and Washington. All U.S. Forest

Land and the state of California (Public Resources Codes 4442

and 4443), Oregon and Washington require, by law that certain

internal combustion engines operated on forest brush and/or

grass-covered areas be equipped with a spark arrestor,

maintained in effective working order, or the engine be

constructed, equipped and maintained for the prevention of

fire. Check with your state or local authorities for regulations

pertaining to these requirements. Failure to follow these

requirements could subject you to liability or a fine. This unit is

factory equipped with a spark arrestor. If it requires

replacement, ask your LOCAL SERVICE DEALER to install the

Accessory Part #753-05169 Spark Arrestor Kit.

CALIFORNIA PROPOSITION 65 WARNING

P/N 769-02886 (01/07)

TABLE OF CONTENTS

Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . . . . . . .2

Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Oil and Fuel Information . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Starting/Stopping Instructions . . . . . . . . . . . . . . . . . . . . . .9

Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Maintenance and Repair Instructions . . . . . . . . . . . . . . .12

Cleaning and Storage . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . .19, 20

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E22

WARNING

THE ENGINE EXHAUST FROM THIS PRODUCT CONTAINS

CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO

CAUSE CANCER, BIRTH DEFECTS OR OTHER

REPRODUCTIVE HARM.

READ ALL INSTRUCTIONS BEFORE OPERATING

• Read the instructions carefully. Be familiar with the controls

and proper use of the unit.

• Do not operate this unit when tired, ill, or under the influence

of alcohol, drugs, or medication.

• Children and teens under the age of 15 must not use the

unit, except for teens guided by an adult.

• All guards and safety attachments must be installed properly

before operating the unit.

• Inspect the unit before use. Replace damaged parts. Check

for fuel leaks. Make sure all fasteners are in place and

secure. Replace parts that are cracked, chipped, or

damaged in any way. Do not operate the unit with loose or

damaged parts.

• Carefully inspect the area before starting the unit. Remove all

debris and hard or sharp objects such as glass, wire, etc.

• Be aware of the risk of injury to the head, hands and feet.

• Clear the area of children, bystanders, and pets. At a minimum,

keep all children, bystanders, and pets outside a 50 feet (15 m.)

radius; there still may be a risk to bystanders from thrown

objects. Bystanders should be encouraged to wear eye

protection. If you are approached, stop the unit immediately.

• Use only 0.105 inch (2.67 mm) diameter original equipment

manufacturer replacement line. Never use metal-reinforced

line, wire or rope. These can break off and become

dangerous projectiles.

• Squeeze the throttle control and check that it returns

automatically to the idle position. Make all adjustments or

repairs before using unit.

SAFETY WARNINGS FOR GAS UNITS

• Store fuel only in containers specifically designed and approved

for the storage of such materials.

• Avoid creating a source of ignition for spilled fuel. Do not

start the engine until fuel vapors dissipate.

• Always stop the engine and allow it to cool before filling the

fuel tank. Never remove the cap of the fuel tank, or add fuel,

when the engine is hot. Never operate the unit without the

fuel cap securely in place. Loosen the fuel tank cap slowly to

relieve any pressure in the tank.

• Mix and add fuel in a clean, well-ventilated outdoor area

where there are no sparks or flames. Slowly remove the fuel

cap only after stopping engine. Do not smoke while fueling

or mixing fuel. Wipe up any spilled fuel from the unit

immediately. Always wipe unit dry before using.

• Move the unit at least 30 feet (9.1 m) from the fueling source

and site before starting the engine. Do not smoke or allow

sparks and open flames near the area while adding fuel or

operating the unit.

WHILE OPERATING

• Never start or run the unit inside a closed room or building.

Breathing exhaust fumes can be fatal. Operate this unit only

in a well-ventilated outdoor area.

• Wear safety glasses or goggles that meet ANSI Z87.1

standards and are marked as such. Wear ear/hearing protection

when operating this unit. Wear a face or dust mask if the

operation is dusty.

• Wear heavy long pants, boots, gloves and a long sleeve

shirt. Do not wear loose clothing, jewelry, short pants,

sandals or go barefoot. Secure hair above shoulder level.

• The cutting attachment shield must always be in place while

operating the unit as a trimmer. Do not operate unit without

both trimming lines extended, and the proper line installed. Do

not extend the trimming line beyond the length of the shield.

• This unit has a clutch. The cutting attachment remains

stationary when the engine is idling. If it does not, have the

unit adjusted by an authorized service technician.

• Adjust the J-handle to your size in order to provide the best grip.

• Be sure the cutting attachment is not in contact with anything

before starting the unit.

• Use the unit only in daylight or good artificial light.

• Avoid accidental starting. Be in the starting position whenever

pulling the starter rope. The operator and unit must be in a stable

position while starting. Refer to Starting/Stopping Instructions.

• Use the right tool. Only use this tool for its intended purpose.

• Do not overreach. Always keep proper footing and balance.

• Always hold the unit with both hands when operating. Keep

a firm grip on both handles or grips.

• Keep hands, face, and feet at a distance from all moving parts. Do

not touch or try to stop the cutting attachment when it rotates.

• Do not touch the engine, gear housing or muffler. These parts get

extremely hot from operation, even after the unit is turned off.

• Do not operate the engine faster than the speed needed to

cut, trim or edge. Do not run the engine at high speed when

not cutting.

• Always stop the engine when cutting is delayed or when

walking from one cutting location to another.

• If you strike or become entangled with a foreign object, stop

the engine immediately and check for damage. Do not

operate before repairing damage. Do not operate the unit

with loose or damaged parts.

• Stop the unit, switch the engine to off, and disconnect the

spark plug for maintenance or repair.

• Use only original equipment manufacturer replacement parts

and accessories for this unit. These are available from your

authorized service dealer. Use of any unauthorized parts or

accessories could lead to serious injury to the user, or

damage to the unit, and void your warranty.

• Keep unit clean of vegetation and other materials. They may

become lodged between the cutting attachment and shield.

• To reduce fire hazard, replace a faulty muffler and spark

arrestor. Keep the engine and muffler free from grass,

leaves, excessive grease or carbon build up.

WHILE OPERATING WITH CUTTING BLADE

• Read and understand all safety warnings before operating

this unit.

• Always use the shoulder harness when using the brush

blade accessory.

• Keep the J-handle between the operator and cutting

attachment or blade at all times.

• NEVER cut when the cutting blade is 30 inches (76 cm) or

more above the ground level.

• Blade thrust may occur when the spinning blade contacts an

object that it does not immediately cut. Blade thrust can be

violent enough to propel the unit and/or operator in any

direction, possibly causing a loss of control. Blade thrust can

occur without warning if the blade snags, stalls or binds.

This is more likely to occur in areas where it is difficult to see

the material being cut.

• For operation with the brush blade, do not cut anything

thicker than 1/2 inch or a violent kickback could occur.

• Do not attempt to touch or stop the blade when it is rotating.

WARNING: Gasoline is highly flammable, and its

vapors can explode if ignited. Take the following

precautions:

RULES FOR SAFE OPERATION

• IMPORTANT SAFETY INSTRUCTIONS •

• A coasting blade can cause injury while it continues to spin

after the engine is stopped or the throttle trigger is released.

Maintain proper control until the blade has completely

stopped rotating.

• Do not run the unit at high speed when not cutting.

• If you strike or become entangled with a foreign object, stop the

engine immediately and check for damage. Have any damage

repaired before attempting further operations. Do not operate

unit with a bent, cracked or dull blade. Discard blades that are

bent, warped, cracked or broken.

• Do not sharpen the cutting blade. Sharpening the blade can

cause the blade tip to break off while in use. This can result

in severe personal injury. Replace the blade.

• Do not use the cutting blade for edging or as an edger; severe

personal injury to yourself or others may incur. Use the cutting

blade only for the purpose described in this manual.

• Stop the engine IMMEDIATELY if you feel excessive

vibration. Vibration is a sign of trouble. Inspect thoroughly for

loose nuts, bolts or damage before continuing. Repair or

replace affected parts as necessary.

AFTER USE

• Clean cutting blades with a household cleaner to remove any

gum buildup. Oil the blade with machine oil to prevent rust.

• Lock up and store the cutting blade in an appropriate area to

protect the blade from unauthorized use or damage.

OTHER SAFETY WARNINGS

• Never store a fueled unit inside a building where fumes may

reach an open flame or spark.

• Allow the engine to cool before storing or transporting. Be

sure to secure the unit while transporting.

• Store the unit in a dry area, locked up or up high to prevent

unauthorized use or damage, out of the reach of children.

• Never douse or squirt the unit with water or any other liquid.

Keep handles dry, clean and free from debris. Clean after

each use, see Cleaning and Storage instructions.

• Keep these instructions. Refer to them often and use them

to instruct other users. If you loan someone this unit, also

loan them these instructions.

SAVE THESE INSTRUCTIONS

RULES FOR SAFE OPERATION

SAFETY AND INTERNATIONAL SYMBOLS

This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the

operator's manual for complete safety, assembly, operating and maintenance and repair information.

SYMBOL MEANING

• ON/OFF STOP CONTROL

ON / START / RUN

• WARNING - READ OPERATOR'S MANUAL

Read the operator’s manual(s) and follow all warnings

and safety instructions. Failure to do so can result in

serious injury to the operator and/or bystanders.

• ON/OFF STOP CONTROL

OFF or STOP

SYMBOL MEANING

• SAFETY ALERT SYMBOL

Indicates danger, warning or caution. May be used

in conjunction with other symbols or pictographs.

• WEAR EYE AND HEARING PROTECTION

WARNING: Thrown objects and loud noise can

cause severe eye injury and hearing loss. Wear eye

protection meeting ANSI Z87.1 standards and ear

protection when operating this unit. Use a full face

shield when needed.

• KEEP BYSTANDERS AWAY

WARNING: Keep all bystanders, especially

children and pets, at least 50 feet (15 m) from the

operating area.

• THROWN OBJECTS AND ROTATING CUTTER

CAN CAUSE SEVERE INJURY

WARNING: Do not operate without the cutting

attachment shield in place. Keep away from the

rotating cutting attachment.

• HOT SURFACE WARNING

Do not touch a hot muffler, gear housing or cylinder.

You may get burned. These parts get extremely hot

from operation. They remain hot for a short time after

the unit is turned off.

• UNLEADED FUEL

Always use clean, fresh unleaded fuel

• OIL

Refer to operator’s manual for the proper type of

oil.

• BRUSHCUTTERS - REPLACE DULL BLADE

Do not sharpen the cutting blade. Sharpening the

blade can cause the blade tip to break off while in

use. This can result in severe personal injury.

• TRIMMER/ BRUSHCUTTER SAFETY

WARNING: Thrown objects and rotating cutter can

cause severe injury. Keep bystanders, especially

children and pets, at least 50 feet (15 m) away

from the cutting area. The cutting attachment

shield must be used when using the trimmer

cutting attachment.

On some units, the J-handle may be pre-installed. In this case,

loosen the screws and go to step 5.

INSTALL AND ADJUST THE J-HANDLE

1. Place the J-handle between the top and middle clamp

pieces (Fig. 1).

(4) Screws

Top Clamp

J-Handle

Middle Clamp

Bottom Clamp

Nuts

2. While holding the three pieces together, install the four (4)

screws through the top clamp and into middle clamp.

NOTE: The holes in the top and middle clamp will line up only

when assembled correctly.

3. Place the clamps and the J-handle over the shaft housing

and onto the bottom clamp.

Fig. 1

KNOW YOUR UNIT

Cutting Attachment

Shield

Fuel Cap

Throttle

Control

Throttle Lock-Out

J-Handle

Cutting Attachment

Gear Housing

Shaft Grip

Primer Bulb

Blue Choke

Lever

Spark Plug

Engine Stand

On/Off Stop Control

Shaft

Housing

Starter Rope Grip

Blade Shield /

Shield Mount

Brush

Blade

Line Cutting

Blade

Muffler

Shoulder Strap Clip

EZ-Link™

Air Filter/

Muffler

Cover

ASSEMBLY INSTRUCTIONS

4. Hold each hex nut in the

bottom clamp recess with a

finger. Start screws with a

large Phillips screwdriver. Do

not tighten until you make the

handle adjustment.

5. Slide the J-handle in or out until

the arrow/white line on the decal

touches the clamp assembly (Fig.

2). You must first loosen the

screws if the handle is pre-

installed.

6. While holding the unit in the

operating position (Fig. 3),

position the J-handle to the

location that provides you the

best grip.

7. Tighten the clamp screws

evenly, until the J-handle is

secure.

Fig. 2

Fig. 3

Decal

APPLICATIONS

As a trimmer:

• Cutting grass and light weeds

• Edging

• Decorative trimming around trees, fences, etc.

As a brushcutter:

• Cutting weeds and light brush of up to 1/2 inch in diameter

Other optional accessories may be used with the YM90BC. Refer

to Operating the EZ-Link System for a list of add-ons.

INSTALL THE HARNESS

1. Push the strap through the

center of the buckle.

2. Pull the strap over the cross

bar and down through the slot

in the buckle (Fig. 5).

3. Put the harness on over head

and onto shoulder. Snap it on

to the support fitting (Fig. 6).

4. Adjust length to fit the operator’s

size. Pull tab to lengthen, pull

strap to shorten (Fig 7).

Support Fitting

Fig. 6

Fig. 7

REMOVE AND INSTALL THE CUTTING ATTACHMENT SHIELD

Remove the cutting attachment shield when using the unit

as a brushcutter

Remove the cutting attachment shield from the shield mount

by removing the three (3) screws with a flat blade screwdriver

(Fig. 4). Store parts for future use.

REMOVE THE CUTTING ATTACHMENT AND INSTALL THE

CUTTING BLADE

NOTE: To make cutting blade removal and installation easier, place

the unit on the ground or on a work bench

Remove the Cutting Attachment Shield

See Remove and Install the Cutting Attachment Shield.

Remove the Cutting Attachment

Align the shaft bushing hole with the locking rod slot and insert

the locking rod into the shaft bushing hole (Fig. 8).

(3) Screws

Cutting

Attachment

Shield

Shield Mount

Gear Housing

Fig. 4

ASSEMBLY INSTRUCTIONS

WARNING: The cutting attachment shield should

NOT be installed when operating the unit with a

blade. Remove the cutting attachment shield

before removing or installing the blade.

WARNING: Always use the shoulder harness

when using the cutting blade to avoid serious

personal injury.

WARNING: The gear housing gets hot with use.

It can result in injury to the operator. The housing

remains hot for a short time even after the unit is

turned off. Do not touch the gear housing until it

has cooled.

Fig. 5

Install the cutting attachment shield when using the unit as

a grass trimmer

Install the cutting attachment shield on the shield mount by

inserting the three (3) screws into the shield mount. Tighten

securely with a flat blade screwdriver (Fig. 4).

WARNING: To avoid serious personal injury, the

cutting attachment shield MUST be in place at all

times while operating the unit as a grass trimmer.

Shaft Bushing Hole

Locking Rod Slot

Output Shaft

Bushing

Locking Rod

Output Shaft

Fig. 8

2. Hold the locking rod in place by grasping it next to the

boom of the unit (Fig. 9).

3. While holding the locking

rod, remove the cutting

attachment by turning it

clockwise off of the output

shaft (Fig. 10). Store the

cutting attachment for

future use.

NOTE: The blade retainer

under the cutting

attachment will be

used when installing

the cutting blade.

Fig. 9

Cutting Attachment

Locking Rod

Slot

Locking Rod

Fig. 10

Fig. 15

Cutting Attachment

Locking Rod

Clockwise

6. Remove the locking rod.

7. Install the cutting attachment shield. Refer to Remove and

Install the Cutting Attachment Shield.

Blade Retainer

Output Shaft

Bushing

Fig. 14

4. Remove the nut, blade retainer and blade. Store the nut

and blade together for future use in a secure place. Store

out of children’s reach.

Install the Cutting Attachment

Align the shaft bushing hole with the locking rod slot and insert

the locking rod into the shaft bushing hole (Fig. 8). Place the

blade retainer on the output shaft with the flat surface against

the output shaft bushing (Fig. 15). Screw the cutting attachment

counterclockwise onto the output shaft. Tighten securely.

NOTE: The blade retainer must be installed on the output shaft

in the position shown for the cutting attachment to

work correctly.

WARNING: To avoid serious personal injury, the

cutting attachment shield MUST be in place at all

times while operating the unit as a trimmer.

Install the Cutting Blade

4. Place the cutting blade on the output shaft bushing (Fig. 11).

Shield

Mount

Locking Rod

Cutting

Blade

Blade Retainer

Nut

Output Shaft

Bushing

Pilot Hole

Fig. 11

ASSEMBLY INSTRUCTIONS

WARNING: To avoid serious personal injury,

always wear gloves while handling or installing the

blade.

5. Make sure that the cutting blade is centered on the pilot step

and sitting flat against the output shaft bushing (Fig. 12).

WARNING: If the cutting blade is off-center, the

unit will vibrate and the blade may fly off, causing

possible serious personal injury.

Fig. 12

Pilot Step

6. Align the shaft bushing hole with the locking rod

slot and insert the locking rod into the bushing hole (Fig. 8).

7. Put the blade retainer and nut on the output shaft. Make

sure that the blade is installed correctly.

8. Tighten nut counterclockwise against the blade while

holding the locking rod:

• If using a torque wrench and a 13 mm socket tighten to: 325

- 335 in•lb, 27 - 28 ft.•lb, 37 - 38 N•m.

• Without a torque wrench, use a 13 mm closed-end or socket

wrench, turning the nut until the blade retainer is snug

against the shaft bushing. Make sure that the blade is

installed correctly, then rotate the nut an additional 1/4 to 1/2

turn counterclockwise (Fig. 13).

Fig. 13

1/4-1/2 turn

Counterclockwise

9. Remove the locking rod from the locking rod slot.

WARNING: To avoid serious personal injury or

damage to the unit, do not start or operate this unit

with the locking rod in the locking rod slot.

WARNING:

Do not sharpen the cutting blade.

Sharpening the blade can cause the blade tip to break

off while in use. This can result in severe personal

injury. Replace the blade.

REMOVE THE CUTTING BLADE AND INSTALL THE

CUTTING ATTACHMENT

Remove the Cutting Blade

1. Align the shaft bushing hole with the locking rod slot and

insert the locking rod into the bushing hole (Fig. 8).

2. Hold the locking rod in place by grasping it next to the

boom of the unit (Fig. 9).

3. While holding the locking rod, loosen the nut on the blade

by turning it clockwise with a 13 mm closed-end or socket

wrench (Fig. 14).

WARNING: To avoid serious personal injury,

always wear gloves while handling or installing the

blade.

For edging (when using

the line head cutting

attachment with EZ-

Link™ models), lock the

release button of the

cutting attachment into

the 90° edging hole

(Fig. 18).

OPERATING THE EZ-LINk™ SYSTEM

The EZ-Link™ system enables the use of these optional Add-Ons:

Cultivator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBGC

Edger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBLE

Hedge Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBAH*

Straight Shaft Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . TBSS

Turbo Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBTB

Pole Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBPS*

Brushcutter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TBBC*

*Do NOT use this attachment with an electric powered

product.

Removing the Cutting Attachment or Add-On

1. Turn the knob counterclockwise to loosen (Fig. 16).

2. Press and hold the release button (Fig. 16).

3. While firmly holding the upper shaft housing, pull the cutting

attachment or add-on straight out of the EZ-Link™ coupler

(Fig. 17).

Installing the Cutting Attachment or Add-On

NOTE: Place the unit on the ground or on a work bench to

make add-on installation or removal easier.

1. Turn knob counterclockwise to loosen (Fig. 16).

Fig. 16

EZ-Link™ Coupler

Release Button

Guide Recess

Knob

Primary Hole

Upper Shaft Housing

EZ-Link™ Coupler

2. While firmly holding the add-on, push it straight into the

EZ-Link™ coupler (Fig. 17).

NOTE: Aligning the release button with the guide recess will

help installation (Fig. 16).

3. Turn the knob clockwise to tighten (Fig. 18).

Fig. 17

Fig. 18

Knob

Lower Shaft Housing

Release Button

90˚ Edging Hole

(Trimmer Only)

CAUTION: Lock the release button in the

primary hole and securely tighten the knob before

operating this unit.

WARNING: To avoid serious personal injury and

damage to the unit, shut the unit off before

removing or installing add-ons.

CAUTION: Add-ons are to be used in the

primary hole only. Using the wrong hole could

lead to personal injury or damage to the unit.

WARNING: When using any attachment, read

and understand that attachment’s specific manual

before you begin operation. Follow all applicable

safety information.

ASSEMBLY INSTRUCTIONS

OIL AND FUEL INFORMATION

OIL AND FUEL MIXING INSTRUCTIONS

Old and/or improperly mixed fuel are the main reasons for the unit

not running properly. Be sure to use fresh, clean unleaded fuel.

Follow the instructions carefully for the proper fuel/oil mixture.

Definition of Blended Fuels

Today's fuels are often a blend of gasoline and oxygenates

such as ethanol, methanol, or MTBE (ether). Alcohol-blended

fuel absorbs water. As little as 1% water in the fuel can make

fuel and oil separate. It forms acids when stored. When using

alcohol-blended fuel, use fresh fuel (less than 60 days old).

Using Blended Fuels

If you choose to use a blended fuel, or its use is unavoidable,

follow recommended precautions:

• Always use the fresh fuel mix explained in your operator's manual

• Always agitate the fuel mix before fueling the unit

• Drain the tank and run the engine dry before storing the unit

Using Fuel Additives

The bottle of 2-cycle oil that came with your unit contains a

fuel additive which will help inhibit corrosion and minimize the

formation of gum deposits. It is recommended that you use our

2-cycle oil with this unit.

If unavailable, use a good 2-cycle oil de-signed for air-cooled

engines along with a fuel additive, such as STA-BIL

Gas

Stabilizer or an equivalent. Add 0.8 oz. (23 ml.) of fuel additive

per gallon of fuel according to the instructions on the container.

NEVER add fuel additives directly to the unit's fuel tank.

NOTE: Dispose of the old fuel/oil mix in accordance to

Federal, State and Local regulations.

Thoroughly mix the proper ratio of 2-cycle engine oil with

unleaded gasoline in a separate fuel can. Use a 40:1 fuel/oil

ratio. Do not mix them directly in the engine fuel tank. See the

table below for specific gas and oil mixing ratios.

NOTE: One gallon (3.8 liters) of unleaded gasoline mixed with

one 3.2 oz. (95 ml.) bottle of 2-cycle oil makes a 40:1

fuel/oil ratio.

UNLEADED GAS 2 CYCLE OIL

1 GALLON US

(3.8 LITERS)

3.2 FL. OZ.

(95 ml)

1 LITER 25 ml

MIXING RATIO - 40:1

WARNING: Gasoline is extremely flammable.

Ignited vapors may explode. Always stop the engine

and allow it to cool before filling the fuel tank. Do not

smoke while filling the tank. Keep sparks and open

flames at a distance from the area.

WARNING:

Remove fuel cap slowly to avoid injury

from fuel spray. Never operate the unit without the

fuel cap securely in place

WARNING: Add fuel in a clean, well ventilated

outdoor area. Wipe up any spilled fuel immediately.

Avoid creating a source of ignition for spilt fuel. Do

not start the engine until fuel vapors dissipate.

CAUTION: For proper engine operation and

maximum reliability, pay strict attention to the oil and

fuel mixing instructions on the 2-cycle oil container.

Using improperly mixed fuel can severely damage

the engine.

STARTING INSTRUCTIONS

Fig. 19

Throttle Control

STOPPING INSTRUCTIONS

1. Release your finger from the throttle control. Allow the engine

to cool down by idling.

2. Press and hold On/Off Stop Control in the OFF (O) position until

engine comes to a complete stop (Fig. 19).

Fig. 21

Starting

Position

Trimmer

Equipped With

Spring Assist

Starting ™

Start/On ( I )

Stop/Off (O)

Throttle

Control

Throttle

Lock-Out

Fig. 20

Blue Choke

Lever

Primer

Bulb

1. Mix gas with oil. Fill fuel tank with fuel/oil mixture. See

Oil and Fuel Mixing Instructions.

NOTE: There is no need to turn the unit on. The

On/Off Stop Control is in the ON ( I ) position at all

times (Fig. 19).

2. Fully press and release the primer bulb 10 times,

slowly. Some amount of fuel should be visible in the

primer bulb and fuel lines (Fig. 20). If you can’t see

fuel in the bulb, press and release the bulb as many

times as it takes before you can see fuel in it.

3. Place the blue choke lever in Position 1 (Fig. 20).

4. Crouch in the starting position (Fig. 21), squeeze the

throttle lock-out and throttle control (Fig. 19), and pull

the starter rope out with a controlled and steady

motion 5 times.

NOTE: The unit uses Spring Assist Starting™, which

significantly reduces the effort required to start the

engine. You must pull the starter rope out far enough

to hear the engine attempt to start. There is no need

to pull the rope briskly-- there is no harsh resistance

when pulling. Be aware that this starting method is

vastly different from (and much easier than) what you

may be used to.

5. Place the blue choke lever in Position 2 (Fig. 20).

6. While squeezing the throttle lock-out and throttle

control, pull the starter rope out with a controlled and

steady motion until the engine starts.

7. Squeeze the throttle lock-out and the throttle control

for 15 to 30 seconds to warm up the engine.

NOTE: Engine may take longer to warm up and reach

maximum operating speed at colder temperatures.

NOTE: Unit is properly warmed up when engine

accelerates without hesitation.

8. Once the engine is warmed up, place the blue choke

lever in Position 3 (Fig. 20). The unit is ready for use.

IF...

the engine hesitates, return the blue choke lever to

Position 2 (Fig. 20) and continue warm-up.

IF...

the engine does not start, go back to step 2.

IF...

the engine fails to start after a few attempts, place the

blue choke lever in Position 3 and squeeze the

throttle control. Pull the starter rope out with a

controlled and steady motion 3 to 8 times. The

engine should start. If not, repeat.

IF WARM...

If the engine is already warm, start the unit

with the blue choke lever in Position 2. After the unit

starts, move the blue choke lever to Position 3.

STARTING/STOPPING INSTRUCTIONS

WARNING: Avoid accidental starting. Make sure you are

in the starting position when pulling the starter rope

(Fig. 21).

To avoid serious injury, the operator and unit must

be in a stable position while starting.

Make sure that any Add-On item is installed correctly and

secure before starting the unit.

WARNING:

Operate this unit only in a well- ventilated

outdoor area. Carbon monoxide exhaust fumes can be lethal

in a confined area.

OPERATING INSTRUCTIONS

Fig. 24

DECORATIVE TRIMMING

Decorative trimming is accomplished by removing all vegetation

around trees, posts, fences and more. Rotate the whole unit so

that the cutting attachment is at a 30° angle to the ground (Fig. 24).

USING THE CUTTING BLADE

WARNING:

Always wear eye, hearing, foot, body

protection and the shoulder strap to reduce the risk

of injury when operating this unit.

Fig. 25

Before operating the unit with the cutting blade, stand in the

operating position (Fig. 25). Refer to Holding the Trimmer.

WARNING: Do not use the cutting blade for

edging or as an edger. Severe personal injury to

yourself or others can result.

NOTE: Do not rest the Bump Head™ on the ground while the

unit is running.

Some line breakage will occur from:

• Entanglement with foreign matter

• Normal line fatigue

• Attempting to cut thick, stalky weeds

• Forcing the line into objects such as walls or fence posts

CAUTION: Do not remove or alter the line cutting

blade assembly. Excessive line length will make the

clutch overheat. This may lead to serious personal

injury or damage to the unit.

ADJUSTING TRIMMING LINE LENGTH

The Bump Head™ cutting attachment allows you to release

trimming line without stopping the engine. To release more line,

lightly tap the cutting attachment on the ground (Fig. 23) while

operating the trimmer at high speed.

NOTE: Always keep the trimming line fully extended. Line release

becomes more difficult as the cutting line becomes shorter.

Fig. 23

Each time the head is bumped, about 1 inch (25.4 mm) of trimming

line is released. A blade in the cutting attachment shield will cut the

line to the proper length if excess line is released. For best results,

tap the Bump Head™ on bare ground or hard soil. If line release is

attempted in tall grass, the engine may stall. Always keep the

trimming line fully extended. Line release becomes more difficult

as the cutting line becomes shorter.

HOLDING THE TRIMMER

Before operating the unit, stand

in the operating position (Fig.

22). Check for the following:

• The operator is wearing eye

protection and proper

clothing

• With a slightly-bent right arm,

the operator’s right hand is

holding the shaft grip

• The operator’s left arm is

straight, the left hand

holding the J-handle

• The unit is at waist level

• The cutting attachment is

parallel to the ground and

easily contacts the grass

without the need to bend over

Once you are in the operating

position, hook the shoulder

strap to the unit.

WARNING: Always wear eye, hearing, foot and

body protection to reduce the risk of injury when

operating this unit.

Fig. 22

TIPS FOR BEST TRIMMING RESULTS

• For best trimming results, operate unit at full throttle.

• Keep the cutting attachment parallel to the ground.

• Do not force the cutting attachment. Allow the tip of the line to

do the cutting, especially along walls. Cutting with more than the

tip will reduce cutting efficiency and may overload the engine.

• Cut grass over 8 inches (200 mm) by working from top to bottom

in small increments to avoid premature line wear or engine drag.

• Cut from left to right whenever possible. Cutting to the right

improves the unit's cutting efficiency. Clippings are thrown

away from the operator.

• Slowly move the trimmer into and out of the cutting area at the

desired height. Move either in a forward-backward or side-to-

side motion. Cutting shorter lengths produces the best results.

• Trim only when grass and weeds are dry.

• The life of your cutting line is dependent upon:

— Proper adherence of trimming techniques (explained above)

— What vegetation is cut

— Where vegetation is cut

For example, the line will wear faster when trimming against a

foundation wall as opposed to trimming around a tree.

Fig. 26

Cutting Blade Operating Tips

To establish a rhythmic cutting procedure:

• Plant feet firmly, comfortably apart.

• Bring the engine to full throttle before entering the material to

be cut. At full throttle the blade has maximum cutting power

and is less likely to bind, stall or cause blade thrust (which

can result in serious personal injury to the operator or others).

• Cut while swinging the upper part of your body from left to right.

• Always release the throttle trigger and allow the engine to

return to idle speed when not cutting.

• When you are finished, always unsnap the unit from the

harness before taking off the harness.

• Swing the unit in the opposite direction as the blade spins,

which increases the cutting action.

• After the return swing, move forward to the next area to be

cut plant your feet again.

WARNING:

The blade continues to spin after the

engine is turned off. The coasting blade can

seriously cut you if accidentally touched.

WARNING: Bl

ade thrust may occur when the

spinning blade contacts an object that it does not

immediately cut. Blade thrust can be violent enough

to cause the unit and/or operator to be propelled in

any direction, and possibly lose control of the unit.

Blade thrust can occur without warning if the blade

snags, stalls or binds. This is more likely to occur in

areas where it is difficult to see the material being cut.

WARNING: Do not clear away any cut material

with the engine running or blade turning. To avoid

serious personal injury, turn off the engine. Allow

the blade to stop before removing materials

wrapped around the blade shaft.

OPERATING INSTRUCTIONS

• The cutting blade is designed with a second cutting edge.

You can use it by removing the blade, turning it upside down,

and reinstalling it.

To reduce the chance of material wrapping around the blade,

follow these steps:

• Cut at full throttle

• Swing the unit into material to be cut from your left to your

right (Fig. 26)

WARNING: Do not sharpen the cutting blade.

Sharpening the blade can cause the blade tip to break

off while in use. This can result in severe personal

injury to yourself or others. Replace the blade.

• Avoid the material just cut as you make the return swing

Fig. 30

NOTE: SplitLine™ can only be used with the inner reel with the

slotted holes. Single line can be used on either type of

inner reel. Use Figure 30 to identify the inner reel you have.

Slotted

Holes

For Use with SplitLine™

or Single Line

For Use with Single

Line ONLY

MAINTENANCE SCHEDULE

Perform these required maintenance procedures at the

frequency stated in the table. These procedures should also be

a part of any seasonal tune-up.

NOTE: Some maintenance procedures may require special

tools or skills. If you are unsure about these procedures

take your unit to any non-road engine repair

establishment, individual or authorized service dealer.

NOTE: Maintenance, replacement, or repair of the emission

control devices and system may be performed by any

non-road engine repair establishment, individual or

authorized service dealer.

In order to assure peak performance of your engine, inspection

of the engine exhaust port may be necessary after 50 hours of

operation. If you notice lost RPM, poor performance or general

lack of acceleration, this service may be required. If you feel

your engine is in need of this inspection, refer service to any

non-road engine repair establishment, individual or authorized

service dealer for repair. DO NOT attempt to perform this

process yourself as engine damage may result from

contaminants involved in the cleaning process for the port.

FREQUENCY MAINTENANCE REQUIRED REFER TO

Before starting engine Fill fuel tank with fresh fuel Page 8

Every 10 hours Clean and re-oil air filter Page 14

Every 25 hours

Check and clean spark arrestor

Check spark plug condition and gap

Page 14

Page 15

Every 50 hours

Inspect exhaust port and spark arrestor screen for clogging or

obstruction to assure maximum performance levels

Page 14

Indexing Teeth

Fig. 28

Fig. 29

LINE INSTALLATION

This section covers both SplitLine™ and standard single line

installation.

Always use original equipment manufacturer 0.105 in. (2.67

mm) replacement line. Other types of line may make the engine

overheat or fail.

There are two methods to replace the trimming line:

• Wind the inner reel with new line

• Install a prewound inner reel

Winding the Existing Inner Reel

1. Hold the outer spool with one hand and unscrew the Bump

Knob clockwise (Fig. 27). Inspect the bolt inside the bump

knob to make sure it moves freely. Replace the bump knob if

damaged.

2. Remove the inner reel from the outer spool (Fig. 27).

3. Remove spring from the inner reel (Fig. 27).

4. Use a clean cloth to clean the the inner reel, spring, shaft

and inner surface of the outer spool (Fig. 28).

5. Check the indexing teeth on the inner reel and outer spool

for wear (Fig. 29). If necessary, remove burrs or replace the

reel and spool.

Inner Reel

Spring

Outer Spool

Bump Knob

Bolt

Fig. 27

MAINTENANCE AND REPAIR INSTRUCTIONS

WARNING: Never use metal-reinforced line,

wire, chain or rope. These can break off and

become dangerous projectiles.

WARNING: To prevent serious injury, never

perform maintenance or repairs with unit running.

Always service and repair a cool unit. Disconnect the

spark plug wire to ensure that the unit cannot start.

Fig. 36

Screws

Blue Choke

Lever

Fig. 31

Fig. 32

Fig. 34

Fig. 35

NOTE: Always use the correct line length when installing trimming

line on the unit. The line may not release properly if the line

is too long.

Single Line Installation

Go To Step 8 for SplitLine™ Installation

6. Take approximately 18 feet (6 m) of new trimming line, loop it

into two equal lengths. Insert each end of the line through one

of the two holes in the inner reel (Fig. 31). Pull the line through

the inner reel so that the loop is as small as possible.

Spring

7. Wind the lines in tight even layers, onto the reel (Fig. 32). Wind

the line in the direction indicated on the inner reel. Place your

index finger between the two lines to stop the lines from over-

lapping. Do not overlap the ends of the line. Proceed to step 11.

SplitLine™ Installation

8. Take approximately 9 feet (3 m) of new trimming line. Insert

one end of the line through one of the two holes in the inner

reel (Fig. 33). Pull the line through the inner reel until only

about 4 inches is left out.

9. Insert the end of the line into the open hole in the inner reel and

pull the line tight to make the loop as small as possible (Fig. 33).

Loop

Holding Slots

13. Insert the ends of the line through the eyelets in the outer

spool and place inner reel with spring inside the outer spool

(Fig. 35). Push the inner reel and outer spool together.

While holding the inner reel and outer spool, grasp the ends and

pull firmly to release the line from the holding slots in the reel.

10. Before winding, split the line back about 6 inches.

11. Wind the line in tight even layers in the direction indicated

on the inner reel.

NOTE: Failure to wind the line in the direction indicated will cause

the cutting attachment to operate incorrectly.

12. Insert the ends of the line into the two holding slots (Fig. 34).

Fig. 33

MAINTENANCE AND REPAIR INSTRUCTIONS

AIR FILTER MAINTENANCE

Removing the Air Filter/Muffler Cover

1. Place the blue choke lever in Position 2.

2. Remove the four (4) screws securing the air filter/muffler

cover (Fig. 24). Use a flat blade or T20 Torx bit screwdriver.

3. Pull the cover from the engine. Do not force.

INSTALLING A PREWOUND REEL

1. Hold the outer spool with one hand and unscrew the bump knob

clockwise (Fig. 27). Inspect the bolt inside the bump knob to

make sure it moves freely. Replace the bump knob if damaged.

2. Remove the old inner reel from the outer spool (Fig. 27).

3. Remove the spring from the old inner reel (Fig. 27).

4. Place the spring in the new inner reel.

NOTE: The spring must be assembled on the inner reel before

reassembling the cutting attachment.

5. Insert the ends of the line through the eyelets in the outer

spool (Fig. 35).

6. Place the new inner reel inside the outer spool. Push the inner

reel and outer spool together. While holding the inner reel and

outer spool, grasp the ends and pull firmly to release the line

from the holding slots in the spool.

7. Hold the inner reel in place and install the bump knob by

turning counterclockwise. Tighten securely.

WARNING: To avoid serious personal injury,

always turn your unit off and allow it to cool

before you clean or service it.

NOTE: The spring must be assembled on the inner reel before

reassembling the cutting attachment.

14. Hold the inner reel in place and install the bump knob by

turning counterclockwise. Tighten securely.

SPARK ARRESTOR MAINTENANCE

1. Remove air filter/muffler cover. Refer to Removing the Air

Filter/Muffler Cover.

2. Locate the muffler, but do not remove it. Find the screw on

the bottom of the muffler (Fig. 41). Remove the screw using

either a torx #20 or flat blade screwdriver.

Fig. 41

Spark Arrestor

Screen

Spark Arrestor

Hood

Screw

Muffler

Engine

Tabs

Slots

Cleaning the Air Filter

Clean and re-oil the air filter every 10 hours of operation. It is an

important item to maintain. Failure to maintain your air filter

properly can result in poor performance or can cause

permanent damage to your engine.

1. Remove air filter/muffler cover. Refer to Removing the Air

Filter/Muffler Cover.

2. Turn cover over and look inside to locate the air filter. Remove

the air filter from inside the air filter/muffler cover (Fig. 37).

3. Wash the filter in detergent and water (Fig. 38). Rinse the

filter thoroughly. Squeeze out excess water. Allow it to dry

completely.

Fig. 37

Fig. 38

Fig. 39

Fig. 40

6. Replace the air filter inside the air filter/muffler cover (Fig. 37).

NOTE: Operating the unit without the air filter and air

filter/muffler cover assembly will VOID the warranty.

Reinstalling the Air Filter/Muffler Cover

1. Place the air filter/muffler cover over the back of the

carburetor and muffler. Align the screw holes.

2. Insert the four (4) screws into the holes in the air

filter/muffler cover (Fig. 36) and tighten.

Do not over tighten.

Air Filter

Inside Muffler

Cover

MAINTENANCE AND REPAIR INSTRUCTIONS

4. Apply enough clean SAE 30 oil to lightly coat the filter (Fig. 39).

5. Squeeze the filter to spread and remove excess oil (Fig. 40).

3. Carefully pry up the left side spark arrestor hood. Two tabs

act as hinges on the right side of the hood. Flip open the

spark arrestor hood like a door and then pull its tabs out of

the muffler slots.

4. Using a small flat blade screwdriver, carefully pry the spark

arrestor screen out from the inside of the spark arrestor hood.

5. Clean the spark arrestor screen with a wire brush. Replace it

if it is damaged, or if you are unable to clean it thoroughly.

6. Reinstall the spark arrestor screen snugly back into the

spark arrestor hood.

7. Reinstall the two hood tabs into the two muffler slots and

flip the spark arrestor hood closed.

8. Replace the screw you removed in Step 2 and tighten it

securely.

9. Reinstall the air filter/muffler cover.

WARNING:

If the spark arrestor hood and spark

arrestor screen are not tightened securely, they could

fall off causing damage to the unit and possible

serious personal injury.

MAINTENANCE AND REPAIR INSTRUCTIONS

Fig. 42

Idle Speed

Screw

CARBURETOR ADJUSTMENT

The idle speed of the engine is adjustable through the air

filter/muffler cover (Fig. 42).

NOTE: Careless adjustments can seriously damage your unit.

An authorized service dealer should make carburetor

adjustments.

Check Fuel Mixture

Old and/or improperly mixed fuel is usually the reason for

improper unit performance. Drain and refill the tank with fresh,

properly-mixed fuel prior to making any adjustments. Refer to

Oil and Fuel Information.

Clean Air Filter

The condition of the air filter is important to the operation of the

unit. A dirty air filter will restrict air flow and change the air/fuel

mixture. This is often mistaken for an out of adjustment

carburetor. Check the condition of the air filter before adjusting

the idle speed screw. Refer to Air Filter Maintenance.

Adjust Idle Speed Screw

If, after checking the fuel mixture and cleaning the air filter, the

engine still will not idle, adjust the idle speed screw as follows:

1. Start the engine and let it run at a high idle for a minute to

warm up. Refer to Starting/Stopping Instructions.

2. Release the throttle trigger and let the engine idle. If the

engine stops, insert a small phillips or flat blade

screwdriver into the hole in the air filter/muffler cover (Fig.

42). Turn the idle speed screw in, clockwise, 1/8 of a turn

at a time (as needed) until the engine idles smoothly.

CLEANING

Use a small brush to clean off the outside of the unit. Do not

use strong detergents. Household cleaners that contain

aromatic oils such as pine and lemon, and solvents such as

kerosene, can damage plastic housing or handle. Wipe off any

moisture with a soft cloth.

STORAGE

• Never store the unit with fuel in the tank where fumes may

reach an open flame or spark.

• Allow the engine to cool before storing.

• Store the unit locked up to prevent unauthorized use or damage.

• Store the unit in a dry, well-ventilated area.

• Store the unit out of the reach of children.

LONG TERM STORAGE

If the unit will be stored for an extended time, use the following

storage procedure:

1. Drain all fuel from the fuel tank into a container with the

same 2-cycle fuel mixture. Do not use fuel that has been

stored for more than 60 days. Dispose of the old fuel/oil

mix in accordance to Federal, State and Local regulations.

2. Start the engine and allow it to run until it stalls. This

ensures that all fuel has been drained from the carburetor.

3. Allow the engine to cool. Remove the spark plug and put 1

oz. (30 ml) of any high quality motor oil or 2-cycle oil into

the cylinder. Pull the starter rope slowly to distribute the oil.

Reinstall the spark plug.

NOTE: Remove the spark plug and drain all of the oil from the

cylinder before attempting to start the trimmer after storage.

4. Thoroughly clean the unit and inspect it for any loose or

damaged parts. Repair or replace damaged parts and tighten

loose screws, nuts or bolts. The unit is ready for storage.

REPLACING THE SPARK PLUG

Use a Champion RDJ7Y spark plug (or equivalent). The correct

air gap is 0.025 inch (0.635 mm). Remove the plug after every

25 hours of operation and check its condition.

1. Stop the engine and allow it to cool. Grasp the plug wire

firmly and pull it from the spark plug.

2. Clean around the spark plug. Remove the spark plug from

the cylinder head by turning a 5/8 in. socket

counterclockwise.

3. Replace a cracked, fouled or dirty spark plug. Set the air

gap at 0.025 in. (0.635 mm) using a feeler gauge (Fig. 43).

4. Install a correctly-gapped spark plug in the cylinder head.

Tighten by turning the 5/8-inch socket clockwise until snug.

If using a torque wrench torque to:

110-120 in.•lb. (12.3-13.5 N•m)

Do not over tighten.

NOTE: The cutting attachment should not rotate when the

engine idles.

3. If the cutting attachment rotates when the engine idles, turn

the idle speed screw counterclockwise 1/8 of a turn at a

time (as needed), to reduce idle speed.

Checking the fuel mixture, cleaning the air filter, and adjusting

the idle speed should solve most engine problems.

If not and all of the following are true:

• The engine will not idle

• The engine hesitates or stalls on acceleration

• There is a loss of engine power

Have the carburetor adjusted by an authorized service dealer.

WARNING: The cutting attachment may spin

during idle speed adjustments. Wear protective

clothing and observe all safety instructions to prevent

serious personal injury.

WARNING: To prevent serious personal injury,

make sure the cutting attachment has stopped

rotating before you turn it off and set it down.

WARNING: To avoid serious personal injury,

always turn your unit off and allow it to cool before

you clean or service it.

WARNING: Do not sand blast, scrape or clean

electrodes. Grit in the engine could damage the

cylinder.

0.025 in.

(0.635 mm)

Fig. 43

TRANSPORTING

• Allow the engine to cool

before transporting.

• Drain fuel from unit.

• Tighten fuel cap before

transporting.

• Secure the unit while

transporting.

TROUBLESHOOTING

If further assistance is required, contact your authorized service dealer.

CAUSE ACTION

Air filter is plugged Replace or clean the air filter

Old or improperly mixed fuel Drain gas tank and add fresh fuel mixture

Improper carburetor adjustment Adjust according to the Carburetor Adjustments section or take

to an authorized service dealer for an adjustment

CAUSE ACTION

Empty fuel tank Fill fuel tank with properly mixed fuel

Primer bulb wasn't pressed enough Press primer bulb fully and slowly 10 times

Engine is flooded Place blue choke lever in position 3, squeeze the trigger and

pull the starter rope

Old or improperly mixed fuel Drain gas tank and add fresh fuel mixture

Fouled spark plug Replace or clean the spark plug

Plugged spark arrestor Clean or replace spark arrestor

The outside temperature is below 40º F Place blue choke lever in position 3, pull the starter rope up to

10-15 times

The outside temperature is above 90º F Place blue choke lever in position 3, squeeze the throttle control

and pull the starter rope

CAUSE ACTION

Old or improperly mixed fuel Drain gas tank and add fresh fuel mixture

Improper carburetor adjustment Adjust according to the Carburetor Adjustments section or take

to an authorized service dealer for an adjustment

Fouled spark plug Replace or clean the spark plug

Plugged spark arrestor Clean or replace spark arrestor

CAUSE ACTION

Old or improperly mixed fuel Drain gas tank and add fresh fuel mixture

Improper carburetor adjustment Adjust according to the Carburetor Adjustments section or take

to an authorized service dealer for an adjustment

Cutting attachment bound with grass Stop the engine and clean the cutting attachment

Dirty air filter Clean or replace the air filter

Plugged spark arrestor Clean or replace spark arrestor

CAUSE ACTION

Cutting attachment bound with grass Stop the engine and clean cutting attachment

Cutting attachment out of line Refill with new line

Inner reel bound up Replace the inner reel

Cutting head dirty Clean inner reel and outer spool

Line welded Disassemble, remove the welded section and rewind

Line twisted when refilled Disassemble and rewind the line

Not enough line is exposed Push the bump knob and pull out line until 4 inches (102 mm) of

line is outside of the cutting attachment

CAUSE ACTION

Oil, cleaner or lubricant in cutting head Clean and thoroughly dry the cutting head

ENGINE WILL NOT START

ENGINE WILL NOT IDLE

ENGINE WILL NOT ACCELERATE

ENGINE LACKS POWER OR STALLS WHEN CUTTING

CUTTING ATTACHMENT WILL NOT ADVANCE LINE

CUTTING LINE ADVANCES UNCONTROLLABLY

ENGINE*

* All specifications are based on the latest product information available at the time of printing. We reserve the right to make changes

at any time without notice.

Engine Type............................................................................................................................................................... Air-Cooled, 2-Cycle

Stroke ......................................................................................................................................................................... 1.25 in. (31.75 mm)

Displacement .................................................................................................................................................................. 1.9 cu in. (31 cc)

Clutch Type............................................................................................................................................................................... Centrifugal

Idle Speed RPM............................................................................................................................................................ 2,600 - 3,600 rpm

Operating RPM ....................................................................................................................................................................... 6,500+ rpm

Ignition Type............................................................................................................................................................................... Electronic

Ignition Switch............................................................................................................................................................. Momentary Switch

Spark Plug Gap ........................................................................................................................................................ 0.025 in. (0.635 mm)

Lubrication ........................................................................................................................................................................ Fuel/Oil Mixture

Fuel/Oil Ratio....................................................................................................................................................................................... 40:1

Carburetor ............................................................................................................................................................ Diaphragm, All-Position

Starter .................................................................................................................................................................................... Auto Rewind

Muffler .......................................................................................................................................................................... Baffled with Guard

Throttle .................................................................................................................................................................... Manual Spring Return

Fuel Tank Capacity ............................................................................................................................................................ 13 oz. (384 ml)

Drive Shaft Housing ............................................................................................................................................... Steel Tube, EZ-Link™

Throttle Control...................................................................................................................................... Finger-Tip Trigger with Lock-Out

Approximate Unit Weight (No fuel, with J-handle, cutting attachment and shield)....................................................... 14.75 lbs. (6.5 kg)

Cutting Mechanism ...................................................................................................... 4-Tooth Cutting Blade, Dual String Cutting Head

Line Spool .................................................................................................................................................................. Bump Line Releaser

Line Spool Diameter .................................................................................................................................................. 4 inches (101.6 mm)

Trimming Line Diameter............................................................................................................................................ 0.105 inch (2.67 mm)

Cutting Path Diameter, Cutting Attachment .............................................................................................................. 18 inches (45.7 cm)

Cutting Path Diameter, Cutting Blade .......................................................................................................................... 8 inches (204 mm)

Shoulder Harness......................................................................................................................................................... Single Quick-Snap

SPECIFICATIONS

DRIVE SHAFT & CUTTING ATTACHMENT

MANUFACTURER’S LIMITED WARRANTY FOR:

No implied warranty, including any implied warranty of

merchantability or fitness for a particular purpose, applies

after the applicable period of express written warranty

above as to the parts as identified. No other express

warranty or guaranty, whether written or oral, except as

mentioned above, given by any person or entity, including

a dealer or retailer, with respect to any product shall bind

Yard-Man. During the period of the Warranty, the exclusive

remedy is repair or replacement of the product as set forth

above. (Some states do not allow limitations on how long an

implied warranty lasts, so the above limitation may not apply

to you.)

The provisions as set forth in this Warranty provide the

sole and exclusive remedy arising from the sales. Yard-

Man shall not be liable for incidental or consequential loss

or damages including, without limitation, expenses

incurred for substitute or replacement lawn care services,

for transportation or for related expenses, or for rental

expenses to temporarily replace a warranted product.

(Some states do not allow limitations on how long an implied

warranty lasts, so the above limitation may not apply to you.)

In no event shall recovery of any kind be greater than the

amount of the purchase price of the product sold. Alteration of

the safety features of the product shall void this Warranty. You

assume the risk and liability for loss, damage, or injury to you

and your property and/or to others and their property arising

out of the use or misuse or inability to use the product.

This limited warranty shall not extend to anyone other than the

original purchaser, original lessee or the person for whom it

was purchased as a gift.

How State Law Relates to this Warranty: This warranty gives

you specific legal rights, and you may also have other rights

which vary from state to state.

To locate your nearest service dealer dial 1-800-800-7310 in

the United States or 1-800-668-1238 in Canada.

Yard-Man LLC

P.O. Box 361131

Cleveland, OH 44136-0019

The limited warranty set forth below is given by Yard-Man LLC

(“Yard-Man”) with respect with new merchandise purchased

and used in the United States, its possessions and territories.

Yard-Man warrants this product against defects in material and

workmanship for a period of two (2) years commencing on the

date of original purchase and will, at its option, repair or

replace, free of charge, any part found to be defective in

material or workmanship. This limited warranty shall only apply

if this product has been operated and maintained in

accordance with the Operator’s Manual furnished with the

product, and has not been subject to misuse, abuse,

commercial use, neglect, accident, improper maintenance,

alteration, vandalism, theft, fire, water or damage because of

other peril or natural disaster. Damage resulting from the

installation or use of any accessory or attachment not

approved by Yard-Man for use with the product(s) covered by

this manual will void your warranty as to any resulting damage.

This warranty is limited to ninety (90) days from the date of

original retail purchase for any Yard-Man product that is used

for rental or commercial purposes, or any other income-

producing purpose.

HOW TO OBTAIN SERVICE: Warranty service is available,

WITH PROOF OF PURCHASE THROUGH YOUR LOCAL

AUTHORIZED SERVICE DEALER. To locate the dealer in your

area, please check for a listing in the Yellow Pages or contact

the Customer Service Department of Yard-Man by calling 1-

800-800-7310 or writing to P.O. Box 361131, Cleveland OH

44136-0019 or if in Canada call 1-800-668-1238. No product

returned directly to the factory will be accepted unless prior

written permission has been extended by the Customer

Service Department of Yard-Man.

This limited warranty does not provide coverage in the

following cases:

A. Tune-ups - Spark Plugs, Carburetor Adjustments, Filters

B. Wear items - Bump Knobs, Outer Spools,Cutting Line,

Inner Reels, Starter Pulley,Starter Ropes, Drive Belts

C. Yard-Man does not extend any warranty for products sold

or exported outside of the United States of America, its

possessions and territories, except those sold through

Yard-Man’s authorized channels of export distribution.

Yard-Man reserves the right to change or improve the design

of any Yard-Man product without assuming any obligation to

modify any product previously manufactured.

Manuel de L'utilisateur

Starting

Désherbeuse/débroussailleuse

à gaz à 2-temps

YM90BC

CONSERVEZ CES INSTRUCTIONS

Obtenez la liste des concessionnaires agréés appelez le 1-800-

800-7310 aux États-Unis ou le 1-800-668-1238 au Canada.

Pour de plus amples informations à propos de votre appareil,

visitez www.yardman.com.

NE RETOURNEZ PAS L'APPAREIL AU DÉTAILLANT CHEZ

QUI VOUS L'AVEZ ACHETÉ. TOUT SERVICE SOUS

GARANTIE NÉCESSITE UNE PREUVE D'ACHAT.

CE PRODUIT EST COUVERT PAR UN OU PLUSIEURS

BREVETS AMÉRICAINS, ET D’AUTRES SONT EN INSTANCE.

Tout entretien effectué sur cet appareil pendant et après la

période de garantie doit être fait par un concess- ionnaire agréé

uniquement.

Toutes les informations, illustrations et spécifications contenues

dans ce manuel tiennent compte des dernières informations

techniques disponibles au moment de mettre sous presse. Nous

nous réservons le droit d'y apporter des modifications à tout

moment, sans préavis.

AVERTISSEMENT: Lorsque vous utilisez la machine,

vous devez suivre les consignes de sécurité. Veuillez lire

ces instructions avant d’opérer la machine pour vous

assurer de la sécurité de l’opérateur et de tout spectateur.

Veuillez conserver ces instructions pour un usage ultérieur.

PARE-ÉTINCELLES

REMARQUE : à l'intention des utilisateurs opérant dans les

terres forestières des États-Unis et dans les états de

Californie, du Maine, de l'Orégon et de Washington. Toutes

les terres forestières des États-Unis et de l'état de Californie

(Codes sur les ressources publiques 4442 et 4443), de l'Orégon

et de Washington exigent de par la loi que certains moteurs à

combustion interne utilisés dans des zones couvertes de taillis

ou d'herbe soient équipés d'un pare-étincelles en parfait état de

fonctionnement, ou qu'ils soient conçus, équipés et entretenus

pour la prévention des incendies. Renseignez-vous auprès des

autorités de votre province ou de votre municipalité concernant

la réglementation en vigueur. Vous pourriez être passible d'une

amende ou être tenu responsable si vous ne respectez pas cette

réglementation. Cet appareil est équipé d'un pare-étincelles en

usine. Si l'écran pare-étincelles, réf. 753-05169, doit être

remplacé, communiquez avec le service technique.

AVERTISSEMENT DE LA PROPOSITION 65 DE CALIFORNIE

TABLE DES MATIÈRES

Service technique . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F1

Consignes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . .F2

Instructions de montage . . . . . . . . . . . . . . . . . . . . . . . . .F4

Familiarisez-vous avec votre appareil . . . . . . . . . . . . . . .F4

Informations sur l'huile et le carburant . . . . . . . . . . . . . .F8

Instructions de démarrage et d'arrêt . . . . . . . . . . . . . . . .F9

Mode d'emploi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F10

Entretien et réparations . . . . . . . . . . . . . . . . . . . . . . . . .F13

Nettoyage et entreposage . . . . . . . . . . . . . . . . . . . . . . .F15

Tableau de dépannage . . . . . . . . . . . . . . . . . . . . . . . . .F16

Caractéristiques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F17

Garantie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .F19, F20

Liste des pièces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .E22

AVERTISSEMENT

LES GAZ D'ÉCHAPPEMENT DU MOTEUR DE CET APPAREIL

CONTIENNENT DES PRODUITS CHIMIQUES CONSIDÉRÉS PAR

L'ÉTAT DE CALIFORNIE COMME POUVANT CAUSER LE

CANCER, DES MALFORMATIONS CONGÉNITALES OU D'AUTRES

EFFETS NOCIFS SUR L'APPAREIL DE REPRODUCTION.

P/N 769-02886 (01/07)

LISEZ CETTE NOTICE INTEGRALEMENT AVANT

D’UTILISER CET APPAREIL :

• Lisez soigneusement cette notice. Familiarisez-vous avec les

commandes et la marche à suivre pour une bonne utilisation

de l'appareil.

• N’utilisez pas cet appareil lorsque vous êtes fatigué, malade,

ou sous l’influence de l’alcool, de drogues, ou de

médicaments.

• Tout enfant ou adolescent de moins de 15 ans ne doit pas

utiliser cet appareil, à moins que l'adolescent soit sous la

supervision d’un adulte.

• Toutes les protections et tous les dispositifs de sécurité doivent

être installés correctement avant utilisation de l’appareil.

• Inspectez l’appareil avant utilisation. Remplacez les pièces

endommagées. Détectez les fuites de carburant éventuelles.

Assurez-vous que tous les accessoires sont bien en place.

Remplacez les pièces susceptibles d’être fissurées, ébréchées,

ou endommagées. N’utilisez pas cet appareil si des pièces ont

du jeu ou sont endommagées.

• Inspectez la zone avec attention avant de démarrer cet

appareil. Retirez tous les débris et objets durs ou tranchants

tels que du verre, les câbles, etc…

• Soyez conscient des risques de blessures à la tête, aux

mains et aux pieds.

• Eloignez les enfants, les personnes à proximité et les animaux

familiers de la zone d’utilisation. Au minimum, faites reculer les

enfants, les personnes à proximité et les animaux familiers de

50 pieds (15 m) ; il existe néanmoins un risque de projectiles

pour les personnes à proximité. Encouragez-les à porter des

lunettes de sécurité. Si quelqu’un s’approche de vous, arrêtez

l’appareil immédiatement.

• Utilisez uniquement un fil de 0,105 pouces (2,67mm) de

diamètre provenant du fabricant. N’utilisez jamais de câbles,

cordons ou pièces renforcées en métal, qui peuvent céder et

devenir des projectiles dangereux.

• Appuyez sur la manette des gaz et vérifiez que le régime du

moteur revienne automatiquement au ralenti. Effectuez tous

les réglages et réparations avant d’utiliser l’appareil.

ALERTES DE SECURITE POUR LES APPAREILS A ESSENCE

• Stockez uniquement le carburant dans des conteneurs prévus

spécifiquement à cet effet et approuvés pour le stockage de

telles substances.

• Evitez tout ce qui pourrait enflammer le carburant renversé.

Ne démarrez pas le moteur avant que les vapeurs de

carburant ne se soient dissipées.

• Coupez toujours le moteur et laissez-le refroidir avant de remplir

le réservoir d’essence. Ne retirez jamais le bouchon du réservoir

d’essence et ne remplissez jamais ce dernier lorsque le moteur

est chaud. Ne démarrez jamais l’appareil sans avoir bien revissé

le bouchon du réservoir d’essence. Dévissez lentement le

bouchon du réservoir d’essence afin de réduire la pression.

• Mélangez et ajoutez le carburant en extérieur, dans une zone

propre, bien aérée, et dépourvue de toute source d’étincelles ou de

flammes. Dévissez lentement le bouchon du réservoir d’essence

uniquement après avoir arrêté le moteur. Ne fumez pas en

remplissant le réservoir ou en mélangeant le carburant. L’essence

s’étant échappée de l’appareil doit être essuyée immédiatement.

Essuyez l’appareil systématiquement avant utilisation.

• Eloignez l’appareil d’au moins 30 pieds (9,1 m) du site et de

la source du carburant avant de démarrer le moteur. Ne

fumez pas ou assurez-vous qu’il n’y a pas de source

d’étincelles et de flammes, à proximité, lorsque vous ajoutez

du carburant ou faites tourner l’appareil.

LORS DU FONCTIONNEMENT DE L'APPAREIL

• L'appareil ne doit pas être démarré ou opéré à l'intérieur d'un

espace ou d’un bâtiment clos. L’inhalation des fumées

d’échappement peut être fatale. Cet appareil doit fonctionner

uniquement en extérieur, dans une zone bien aérée.

• Portez des lunettes de sécurité conformes aux normes ANSI Z87.1,

lesquelles doivent être indiquées sur les lunettes mêmes. Portez des

bouchons d’oreille et des casques antibruit lors de l’utilisation de cet

appareil. Portez un masque si l'appareil émet de la poussière.

• Portez un pantalon long et épais, des bottes, des gants et

une chemise à manches longues. Ne portez pas de

vêtements amples, de bijoux, de pantalons courts, de

sandales et ne soyez pas pieds nus. Veillez à ce que vos

cheveux restent au-dessus du niveau des épaules.

• L’écran de l’accessoire de coupe doit toujours être utilisé lorsque

vous vous servez de cet appareil comme débroussailleuse.

N'utilisez jamais cet appareil sans une longueur suffisante des

deux fils de coupe, ces derniers devant être ceux recommandés

par le fabricant. La longueur des fils de coupe ne doit jamais aller

au-delà de celle de l’écran.

• Cet appareil dispose d’un embrayage. L'accessoire de coupe

reste immobile lorsque le moteur tourne au ralenti. Dans le cas

contraire, faites ajuster cet appareil par un technicien agréé.

• Ajustez la poignée J à votre taille afin d’assurer une prise optimale.

• Assurez-vous que l’accessoire de coupe n’est pas en contact

avec tout autre élément avant de démarrer l’appareil.

• Utilisez cet appareil uniquement en plein jour ou si vous

disposez d’un éclairage artificiel suffisant.

• Evitez les démarrages accidentels. Soyez en position de

démarrage lorsque vous tirez sur le cordon du démarreur.

L’utilisateur et l’appareil doivent être sur un sol ferme lors du

démarrage. Référez-vous aux consignes relatives au

démarrage/à l’arrêt de l’appareil.

• Utilisez le bon outil. N’utilisez pas un outil pour des fonctions

pour lesquelles il n’a pas été prévu.

• N’étendez pas trop le bras. Restez toujours à distance et en

équilibre.

• Tenez toujours l’appareil à deux mains lorsqu'il est en marche.

Assurez une prise ferme sur les deux poignées ou grips.

• Gardez vos mains, votre visage et vos pieds à distance des

parties en mouvement. Ne touchez pas et ne tentez pas

d'arrêter l'accessoire de coupe lorsqu'il est en rotation.

• Ne touchez pas au moteur, à la transmission ou au pot

d'échappement. Ces parties deviennent extrêmement chaudes

lors du fonctionnement, même après l'arrêt de l'appareil.

• L'appareil ne doit pas fonctionner à un régime supérieur à

celui adapté pour la coupe ou la tonte. Ne faites pas tourner

le moteur à haut régime lorsque vous ne coupez rien.

• Arrêtez toujours le moteur lorsque la coupe est interrompue

ou lorsque vous vous rendez à une autre aire de coupe.

• Si vous butez ou bloquez sur un objet, arrêtez le moteur

immédiatement et vérifiez que l'appareil n'a pas été

endommagé. Ne redémarrez pas l'appareil avant de l'avoir

réparé. Ne faites pas fonctionner l’appareil si certaines

pièces ont du jeu ou sont endommagées.

• Arrêtez l’appareil, coupez le moteur, et déconnectez la

bougie avant de l’entretenir ou de le réparer.

• Pour cet appareil, utilisez uniquement les pièces et accessoires

de rechange du fabricant. Ils sont disponibles auprès d’un

fournisseur officiel. L’utilisation de pièces ou accessoires non

agréés pourrait entraîner de graves blessures pour l'utilisateur,

ou endommager l'appareil, et annuler votre garantie.

• Dégagez l’herbe et les autres substances nichées dans l’appareil.

Elles peuvent se coincer entre l’accessoire de coupe et l’écran.

• Afin de réduire les risques d’incendie, remplacez les réducteurs

anti-flamme et les pots d’échappement défaillants. Nettoyez

l’herbe, les feuilles, les couches de graisse excessives et les

dépôts de carbone du moteur et du pot d’échappement.

EN CAS DE FONCTIONNEMENT AVEC UNE LAME DE COUPE

• Lisez soigneusement toutes les consignes de sécurité avant

de démarrer cet appareil.

• Utilisez toujours la bandoulière lorsque vous utilisez une

lame à débroussailler.

• Veillez à toujours tenir la poignée J devant vous, en la

gardant dans l’axe de l’accessoire de coupe ou la lame.

• N'utilisez JAMAIS cet appareil lorsque la lame de coupe se

situe à 30 pouces (76 cm) ou plus au-dessus du niveau du sol.

• Un choc peut être ressenti lorsque la lame en rotation heurte

un objet qu'elle ne coupe pas immédiatement. Un tel choc

peut être assez violent et faire dévier l'appareil et/ou faire

CONSIGNES DE SÉCURITÉ

• IMPORTANTES CONSIGNES DE SÉCURITÉ •

AVERTISSEMENT: l'essence est extrêmement

inflammable et ses vapeurs peuvent exploser si on

y met le feu. Veuillez prendre les précautions

suivantes.

La page charge ...

MTD YM90BC Manuel utilisateur

Marque: MTD

Modèle: YM90BC

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Ce manuel convient également à

Yard-Man YM90BC

Télécharger le PDF

rapport

dans d''autres langues

English: MTD YM90BC User manual
español: MTD YM90BC Manual de usuario

MTD YM90BC Manuel utilisateur

Ce manuel convient également à

MTD YM90BC Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents