Quadra-Fire 2100 Millennium Wood Stove Le manuel du propriétaire

Marque: Quadra-Fire

Modèle: 2100 Millennium Wood Stove

Catégorie: Cheminées

Taper: Le manuel du propriétaire

102/237039-802G

Owner’s Manual

Operation & Care

INSTALLER: Leave this manual with party responsible for use and operation.

OWNER: Retain this manual for future reference.

Contact your dealer with question on installation, operation, or service.

Installation and service of this appliance should be performed by

qualified personnel. Hearth & Home Technologies recommends

HHT Factory Trained or NFI certified professionals.

NOTE: To obtain a French translation of this manual,

please contact your dealer or visit www.quadrare.com

REMARQUE : Pour obtenir une traduction française de

ce manuel, s’il vous plaît contacter votre revendeur ou

visitez www.quadrare.com

Fire Risk.

For use with solid wood fuel only.

Other fuels may over-re and generate

poisonous gases (i.e. carbon monoxide).

NOTICE: DO NOT DISCARD THIS MANUAL

2100 MILLENNIUM WOOD

APPLIANCE

AUTOMATIC COMBUSTION

CONTROL (ACC)

MODEL NUMBER:

21M-ACC-C

If the information in these instructions is

not followed exactly, a re could result

causing property damage, personal

injury, or death.

• Do not store or use gasoline or other ammable vapors

and liquids in the vicinity of this or any other appliance.

• Do not over-re - If appliance or chimney connector

glows, you are over-ring. Over-ring will void

your warranty.

• Comply with all minimum clearances to combustibles

as specied.

Failure to comply may cause house re.

WARNING

HOT SURFACES!

Glass and other surfaces are hot

during operation AND cool down.

Hot glass and appliance will cause burns.

• Do not touch glass until it is cooled

• Use leather gloves when reloading fuel

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room

as appliance.

• Alert children and adults to hazards of

high temperatures

• High temperatures may ignite clothing or other

ammable materials.

• Keep clothing, furniture, draperies and other

ammable materials away.

WARNING

202/237039-802G

8.50

LISTED ROOM HEATER, SOLID FUEL TYPE. ALSO FOR USE IN MOBILE HOMES. (UM) 84 HUD . "For Use with Solid

Wood Fuel Only" / APPAREIL DE CHAUFFAGE DE PIÈCE, DE TYPE DE COMBUSTIBLE SOLIDE, POUR USAGE

DANS LES MAISONS MOBILES. (UM) 84-64 HUD. "Pour Usage Avec Bois Solide Seulement"

PREVENT HOUSE FIRES / PRÉVENTION DES FEUX DE MAISON

Install and use only in accordance with manufacturer's installation and operating instructions. Contact local building or fire

officials about restrictions and installation inspections in your area. Do not obstruct the space beneath heater. For use with

leg and pedestal options intended for this model, refer to owner’s manual for appropriate part numbers and installation

instructions. WARNING - For Mobile Homes: Do not install in a sleeping room. An outside combustion air inlet must be

provided and unrestricted while unit is in use. The structural integrity of the mobile home floor, ceiling and walls must be

maintained. The stove needs to be properly grounded to the frame of the mobile home. Components required for mobile

home installation: Outside Air Kit, Part Number OAK-ACC. Refer to manufacturer's instructions and local codes for

precautions required for passing chimney through a combustible wall or ceiling and maximum offsets. Inspect and clean

chimney frequently - Under Certain Conditions of Use, Creosote Buildup May Occur Rapidly. Do not connect this unit to a

chimney serving another appliance. Optional Blower, Part BK-ACC. Electrical Rating: 115 VAC, 1.2 Amps, 60 Hz. Route

power cord away from unit. Do not route cord under or in front of appliance. DANGER: Risk of electrical shock.

Disconnect power supply before servicing. Replace glass only with 5mm ceramic available from your dealer. Do not use

grate or elevate fire. Build wood fire directly on hearth. Do not overfire - if heater or chimney connector glows, you are

overfiring. Operate only with the fuel loading door closed. Open only to add fuel to the fire. / Installez et utilisez en accord

avec les instructions d'installation et d'opération du fabricant. Contactez le bureau de la construction ou le bureau des

incendies au sujet des restrictions et des inspections d'installation dans votre voisinage. Ne pas obstruez l'espace en

dessous de l'appareil. AVIS - Pour Les Maisons Mobiles : Ne pas installer dans une chambre à coucher. Un tuyau

extérieur de combustion d'air doit être installé et ne doit pas être obstrué lorsque l'appareil est en usage. La structure

intégrale du plancher, du plafond et des murs de la maison mobile doit être maintenue intacte. L'appareil de chauffage doit

être fixé à la charpente de la maison mobile. Les composants requis pour l'installation des maisons mobiles: Assemblage

d'air extérieur, Numéro de Pièce OAK-ACC. Référez vous aux instructions du fabricant et des codes locaux pour les

précautions requises pour passer une cheminée à travers un mur ou un plafond combustibles, et les compensations

maximums. Inspectez et nettoyez la cheminée fréquemment. Sous certaines conditions, il se peut que la créosote

s'accumule rapidement. Ne pas connecter cet appareil à une cheminée servant un autre appareil. Composants Optionnels:

Ventilateur Optionnel, Pièce BK-ACC. Puissance Électrique: 115 VAC, 1.2 Amps, 60 Hz. Éloignez le fil électrique de

l'appareil. Ne pas faire passer le fil électrique au dessus ou en dessous de l'appareil. DANGER: Il y a risque de décharge

électrique. Déconnectez le fil électrique de la prise de contact avant le service. Remplacez la vitre seulement avec une

vitre céramique de 5 mm disponible chez votre fournisseur. N'élevez pas le feu. Bâtissez le feu de bois directement sur

l'âtre. Ne pas surchauffer. Si l'appareil de chauffage ou le tuyau de cheminée rougissent, vous surchauffez. Opérez

l'appareil seulement lorsque la porte de chargement est fermée. Ouvrez la porte seulement lorsque vous devez ajouter des

combustibles dans le feu.

352 Moutain House Road,

Halifax, PA 17032

www.quadrafire.com

CAUTION:

FLOOR PROTECTION:

Floor protector must be a 3/8 (9.5mm) inch min. thickness, non-combustible

material or equivalent, extending beneath heater and to front/sides/rear as

indicated on the diagram below. Exception: Non-combustible floor

protections must extend beneath the flue pipe when installed with horizontal

venting and extend 2 inches (51mm) beyond each side.

Manufactured by:

Fabriqué par:

HOT WHILE IN OPERATION DO NOT TOUCH, KEEP CHILDREN AND CLOTHING AWAY. CONTACT MAY CAUSE SKIN BURNS. KEEP FURNISHINGS

AND OTHER COMBUSTIBLE MATERIAL FAR AWAY FROM THE APPLIANCE. SEE NAMEPLATE AND INSTRUCTIONS

7039-800B

CHAUD LORS DE L'OPÉRATION. NE PAS TOUCHER. GARDEZ LES ENFANTS ET LES VÊTEMENTS LOIN DE L'ESPACE DÉSIGNÉ DE L'INSTALLATION. LE CONTACT PEUT CAUSER DES

BRÛLURES À LA PEAU. GARDEZ LES MEUBLES ET LES MATÉRIAUX COMBUSTIBLES LOIN DE L'ESPACE DÉSIGNÉ DE L'APPAREIL. VOIR L'ÉTIQUETTE ET LES INSTRUCTIONS.

ATTENTION:

PROTECTION DU PLANCHER:

Le protecteur de plancher doit être d'un minimum de 3/8 inch (9.5mm) d'épaisseur, de matériel

incombustible ou équivalent, s'étendant du dessous de l'appareil de chauffage à l'avant, aux cotés

et à l'arrière comme indiqué sur le diagramme suivant. Exception : Les protections incombustibles

du plancher doivent s'étendre en dessous du conduit de cheminée lorsqu'installées avec une

ventilation à l'horizontale et s'étendre de 2 inches (51mm) de chaque côté.

ALCOVE TOP VIEW /

VUE DU HAUT DE

L'ALCÔVE

ALCOVE SIDE VIEW /

VUE DE CÔTÉ DE L'ALCÔVE

DO NOT REMOVE THIS LABEL / NE PAS ENLEVER L'ÉTIQUETTE

16" from glass 8 in.

USA

Fuel loading door

5-3/4 in. 2-1/4 in."

29-5/8 in.

minimum

39 in.

minimum

CANADA

203mm (8 in.)

203mm

(8 in.)

203mm

(8 in.)

457mm (18 in.)

1245mm

(49 in.)

minimum

1006mm (39-5/8 in.)

minimum

Made in U.S.A. of US and

imported parts.

Fabriqué aux

États-Unis-d’Amérique par des

pièces d’origine américaine et

pièces importées.

U.S. ENVIRONMENTAL PROTECTION AGENCY

Certified to comply with 2020 particulate emission standards at 1.7 g/hr EPA

Method 28 and 5G.

This wood heater needs periodic inspection and repair for proper operation.

Consult the owner’s manual for further information. It is against federal

regulations to operate this wood heater in a manner inconsistent with the

operating instructions in the owner’s manual.

CORNER INSTALLATION /

INSTALLATION DU COIN

BACKWALL/SIDEWALL

MUR ARRIÈRE/MUR DE CÔTÉ

VENT SPECIFICATIONS: / SPÉCIFICATIONS DE LA VENTILATION :

SINGLE WALL: Six inch (6 inches) (152mm) diameter, minimum 24 MSG black or blued steel connector pipe, with a listed factory-built UL103HT* Class "A" chimney, suitable for

use with solid fuels, or a masonry chimney, and the referenced clearances. / MUR SIMPLE : De six (6 inches) (152mm) de diamètre le connecteur de conduit de minimum

d'acier noir ou bleu de minimum de 24MSG, avec une cheminée bâtit en usine UL103HT* de Classe "A", adéquate pour usage avec les combustions solides, ou une cheminée

de briques, avec espaces libres référés.

DOUBLE WALL: Six inch (6 inches) (152mm) diameter, listed double wall air insulated connector pipe with listed factory-built UL103HT* Class "A" chimney, or a masonry

chimney and the referenced clearances / MUR DOUBLE : De six (6 inches) (152mm) de diamètre, le connecteur du conduit d'air isolé pour mur double avec une cheminée bâtit

en usine UL103HT* de Classe "A, ou une cheminée de briques, avec espaces libres alloués.

*In Canada must comply with Standard CAN/ULC-S629-M87 for the 650 degree Factory-built chimneys. / *Au Canada doit conformer a CAN/ULC-S629-M87 la norme pour 650

degré C cheminée bâtit en usine.

MOBILE HOME: Use double wall pipe by Dura-Vent DVL, Selkirk Metalbestos DS or Security DL double wall connector pipe. Must be equipped with a spark arrestor. Apply

double wall clearances below when installing unit. / MAISON MOBILE : Utiliser un conduit de mur double par Dura-Vent DVL, Selkirk Metalbestos DS ou Security DL. Doit êttre

équipé d'un arrêt d'étincelle. Utiliser les espaces libres pour mur double comme mentionné ci-bas.

MINIMUM CLEARANCES TO COMBUSTIBLES In Inches & (Millimeters) / ESPACES LIBRES MINIMUM DES MATÉRIAUX COMBUSTIBLES En Pouces & (millimètres)

NOTE: All "A" , "C" and "F" Dimensions are to inside diameter of the flue collar. / REMARQUE : Toutes les dimensions "A", "C", et "F" sont à partir du diamètre intérieur de

l'entrée du conduit.

TESTED TO: / TESTÉ À :

ASTM E2515,

UL1482, ULC S627-00.

Serial No. / N° de série

BARCODE LABEL

2100 ACC SERIES-C

Report / Rapport

19-530

Report / Rapport

0061WS070S

INSTALLATION: FULL VERTICAL / INSTALLATION : ENTIÈREMENT VERTICALE

SINGLE WALL PIPE A B C D E F G H

Discovery-I-C 18 (457) 11 (279) 24.5 (622) 13 (330) 8.5 (216) 20 (508) 56 (1422) N/A

21M-ACC-C 18 (457) 11 (279) 24.5 (622) 13 (330) 8.5 (216) 20 (508) 56 (1422) N/A

DOUBLE WALL PIPE

Discovery-I-C 11.75 (298) 5 (127) 23 (584) 11.5 (292) 7.5 (191) 19 (483) 43 (1092) N/A

21M-ACC-C 11.75 (298) 5 (127) 23 (584) 11.5 (292) 7.5 (191) 19 (483) 43 (1092) N/A

INSTALLATION: HORIZONTAL WITH MINIMUM 2 FT VERTICAL OFF STOVE TOP / INSTALATION : HORIZONTALE AVEC 609MM VERTICAL MINIMUM DU HAUT DU POÊLE

SINGLE WALL PIPE

Discovery-I-C 17 (432) 10 (254) 23 (584) 11.5 (292) 8.5 (216) 20 (508) 56 (1422) 9.5 (241)

21M-ACC-C 17 (432) 10 (254) 23 (584) 11.5 (292) 8.5 (216) 20 (508) 56 (1422) 9.5 (241)

DOUBLE WALL PIPE

Discovery-I-C 12.5 (318) 5.5 (140) 24.5 (622) 13 (330) 7.5 (191) 19 (483) 43 (1092) 5 (127)

21M-ACC-C 12.5 (318) 5.5 (140) 24.5 (622) 13 (330) 7.5 (191) 19 (483) 43 (1092) 5 (127)

INSTALLATION: ALCOVE - Six inch (6 inches) (152mm) diameter listed DOUBLE WALL air insulated connector pipe with UL103 HT** listed factory-built Class "A" chimney, or a masonry chimney. (Mobile Home must be

equipped with a spark arrestor.) Maximum depth of Alcove shall be no more than 48 inches (1219mm)

with a minimum height of 43 inches (1092mm) to top of unit, and the referenced clearances

INSTALLATION : ALCÔVE -

Six pouces (6 pouces) (152mm) de diamètre listé air isolé tuyau de raccordement à double paroi avec UL103 HT ** cotée Classe usine construite "A" cheminée ou une cheminée de maçonnerie.

(Mobile Home doit être équipé d' un pare-étincelles.) Profondeur maximale de Alcove ne doit pas être plus de 48 pouces (1219mm)

avec une hauteur minimum de 43 inches (1092mm) du haut de l'appareil, et des espaces

libres alloués

DOUBLE WALL PIPE

Discovery-I-C 12.5 (318) 5.5 (140) 24.5 (622) 13 (330) N/A N/A 43 (1092) 5 (127)

21M-ACC-C 12.5 (318) 5.5 (140) 24.5 (622) 13 (330) N/A N/A 43 (1092) 5 (127)

*In Canada must comply with Standard CAN/ULC-S629-M87 for the 650°C Factory-built chimney. /

*Au Canada doit conformer a CAN/ULC-S629-M87 la norme pour 650°C cheminée bâtit en usine.

CONDUIT DU MUR SIMPLE

JAN MAY

SEP

FEB JUN

OCT

MAR

JUL NOV

APR

AUG DEC

21M-ACC-C

DISCOVERY-I-C

2023 2024 2025

90° OFF TOP UP & OUT CEILING CLEARANCE /

DÉGAGEMENT ENTRE LE PLAFOND ET LE HAUT DU

CONDUIT DE CHEMINÉE APRÈS LE COUDE DE 90°

STOVE TO CEILING CLEARANCE / DÉGAGEMENT

ENTRE LE POÊLE ET LE PLAFOND

Serial No.

Safety &

Emissions

Test

Report

Name

Test Lab &

Report No.

Mfg. Date Model

Numbers

A. Sample of Serial Number / Safety Label

LOCATION: Back of appliance

NOTE: Clearances may only be reduced by means approved by the regulatory authority having

jurisdiction

and Welcome to the Quadra-Fire Family!

SAMPLE

302/237039-802G

TABLE OF CONTENTS

Safety Alert Key:

• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.

• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.

• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

• NOTICE: Indicates practices which may cause damage to the appliance or to property.

Quadra-Fire is a registered trademark of Hearth & Home Technologies.

A. Sample of Serial Number / Safety Label ...........2

B. Warranty Policy ..............................4

C. Quick Start Guide.............................6

1 Listing and Code Approvals

A. Appliance Safety Certication ...................7

B. Appliance Emissions Certication ................7

C. BTU & Eciency Specications..................7

D. Glass Specications...........................8

E. Mobile Home Approved ........................8

F. Sleeping Room ...............................8

G. California - Prop65............................8

2 Operating Instructions

A. Over-Firing Your Appliance .....................9

B. Wood Selection & Storage......................9

C. Burning Process..............................9

D. Burn Rates and Operating Eciency.............10

E. Building A Fire ..............................12

F. Blower Operating Instructions...................13

G. Opacity (Smoke) ............................13

H. Clear Space ................................14

I. Negative Pressure............................14

J. Frequently Asked Questions....................15

3 Maintenance and Service

A. Quick Reference Maintenance Guide ............16

B. General Maintenance.........................17

C. Correct Bae & Blanket Placement..............19

4 Troubleshooting Guide .......................20

5 Service Part Replacement

A. Glass .....................................21

B. Firebrick ...................................21

C. Snap Disc..................................22

D. Door Handle Assembly .......................22

E. Bae .....................................23

F. Tube Channel Assembly.......................24

6 Reference Materials

A. Service and Maintenance Log . . . . . . . . . . . . . . . . . .25

B. Service Parts ...............................27

 = Contains updated information



402/237039-802G

Hearth & Home Technologies

LIMITED LIFETIME WARRANTY

Hearth & Home Technologies, on behalf of its hearth brands (“HHT”), extends the following warranty for HHT gas, wood, pellet and

electric hearth appliances that are purchased from an HHT authorized dealer.

WARRANTY COVERAGE:

WARRANTY PERIOD:

distributor, whichever occurs earlier. However, the warranty shall commence no later than 24 months following the date of product

is produced in the following table.

Page 1 of 2

4021-645K 1/20

Parts Labor Gas Pellet Wood Electric Venting Components Covered

X X

Igniters, Auger Motors, Electronic Components, and

Glass

Electrical components limited to modules, remotes/wall

switches, valves, pilots, blowers, junction boxes, wire

harnesses, transformers and lights (excluding light bulbs)

X X Molded Refractory Panels, Glass Liners

XVent Free Burners, Vent Free Logs

X X Castings, Medallions and Baffles

6 years 3 years XCatalyst - Limitations Listed

7 years 3 years X X Manifold tubes, HHT Chimney and Terminations

10 years 1 yearXBurners, logs and refractory

Limited

Lifetime 3 years X X X Firebox and heat exchanger, FlexBurn® System

(engine, inner cover,access cover and fireback)

1 YearNone XXXXXAll replacement parts beyond warranty period

Warranty Period HHT Manufactured Appliances and Venting

All parts including handles, external enamaled

components and other material except as covered by

Conditions, Exclusions, and Limitations listed

2 years

3 years X

X1 YearX X X X

5 years 1 year

Firepots, burnpots, mechanical feeders/auger

assemblies

See condi�ons, exclusions and limita�ons on the next page

B. Warranty Policy

502/237039-802G

WARRANTY CONDITIONS:

• This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor. A list of HHT

authorized dealers is available on the HHT branded websites.

•

• This warranty is only valid in the country in which the HHT authorized dealer or distributor that sold the appliance resides.

• Contact your installing dealer for warranty service. If the installing dealer or distributor is unable to provide necessary parts,

a dealer other than the dealer from whom you originally purchased the product.

• Check with your dealer in advance for any costs to you when arranging a warranty call. Travel and shipping charges for parts are not

covered by this warranty.

• Limited Catalyst Warranty

o For wood burning products containing a catalyst, the catalyst will be warranted for a six-year period to the original purchaser at

catalyst.

WARRANTY EXCLUSIONS:

This warranty does not cover the following:

•

• Repair or replacement of parts that are subject to normal wear and tear during the warranty period are not covered. These parts

•

noise are not covered by this warranty.

•

This warranty is void if:

•

• There is any damage to the appliance or other components due to water or weather damage which is the result of, but not limited

LIMITATIONS OF LIABILITY

•

have other rights, which vary from state to state. EXCEPT TO THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES

OTHER THAN THE WARRANTY SPECIFICED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE

EXPRESSED WARRANTY SPECIFIED ABOVE.

Page 2 of 2

4021-645K 1/20

602/237039-802G

C. Quick Start Guide

1 2 3

4 5

6 7

NOTE: These are generic drawings and may not represent your speci c model.

ITEMS NEEDED FOR FIRST FIRE: 10 Pieces of Newspaper, 10-20 Pieces of Dry

Kindling and Few Pieces of Dry Split Wood.

OPEN AIR

CONTROLS

HIGH

BURN RA

CONTROL

(Upper Right

Corner)

AUTOMATIC

COMBUSTION

CONTROL (ACC)

(Middle right hand side)

HIGH

LOAD WOOD ADD NEWSPAPER

ADD KINDLING

LIGHT THE PAPER

ADD MORE WOOD REDUCE AIR

CONTROLS

Set to desired heat output.

LOW

BURN RATE

CONTROL

(Upper Right

Corner)

AUTOMATIC

COMBUSTION

CONTROL (ACC)

(Middle right hand side)

LOW

The appliance is ready for

normal operation.

Warning! Risk of Fire.

Close and securely latch the door after

the  re has started, and after refueling, to

prevent:

- Spillage of smoke,  ame and carbon

monoxide

- Spillage of sparks, coals, and logs

- Over  ring

DO NOT leave the appliance unattended

with the door open.

Starting a  re may not require an open

door for draft. The air control should

supply adequate draft.

702/237039-802G

This wood appliance needs periodic inspection and repair for proper operation. It is against federal regulations to operate

this wood appliance in a manner inconsistent with operating instructions in this manual.

A. Appliance Safety Certication C. BTU & Eciency Specications

NOTE: This installation must conform with local codes. In the absence of local codes you must comply with (UM) 84-

HUD and NFPA211 in the U.S.A. and CAN/CSA-B365 Installation Codes in Canada.

1 Listing and Code Approvals

Model Number: 21M-ACC-C

Laboratory: OMNI Test Laboratories, Inc.

Report Number: 0061WS070S

Type: Listed Room Appliance, Solid

Fuel Type

Standard: UL1482, ULC S627-00 and (UM)

84-HUD. Mobile Home Approved.

The 21M-ACC-C is Certied

to comply with 2020 crib wood

particulate emission standards.

EPA Certication #: Number: N/A

EPA Certied Emissions: 1.7 grams per hour

*LHV Tested Eciency: 82.3%

**HHV Tested Eciency: 76.1%

***EPA BTU Output: 13,700 to 29,500 / hr.

****Peak BTU/Hour

Output: 44,400

Vent Size: 6 inches

Firebox Size: 1.48 cubic feet

Recommended Log

Length: 16 inches

Fuel Seasoned Cord Wood

(20% moisture)

* Weighted average LHV (Low Heating Value) eciency

using Douglas Fir dimensional lumber and data collected

during EPA emission tests in accordance with the

requirements of CSA B415.1. LHV assumes the moisture

is already in a vapor state so there is no loss in energy to

vaporize.

** Weighted average HHV (High Heating Value) eciency

using Douglas Fir dimensional lumber and data collected

during EPA emission tests in accordance with the

requirements of CSA B415.1. HHV includes the energy

required to vaporize the water in the fuel.

*** A range of BTU outputs calculated using HHV

Eciency and the burn rates from the EPA tests, using

Douglas Fir dimensional lumber.

**** A peak BTU out of the appliance calculated using

the maximum rst hour burn rate from the High EPA Test

and BTU content of seasoned cordwood (8600) times

the eciency.

B. Appliance Emissions Certication

Model Number: 21M-ACC-C

Laboratory: PFS-TECO

Report Number: 19-530

Standard: Method 28 and 5G, and

ASTM E2515

Can be found at:

www.quadrare.com/about-us/epa-certication

802/237039-802G

F. Sleeping Room

G. California - Prop65

This product and the fuels used to operate this product (wood), and the

products of combustion of such fuels, can expose you to chemicals

including carbon black, which is known to the State of California to

cause cancer, and carbon monoxide, which is known to the State of

California to cause birth defects or other reproductive harm. For more

information go to: WWW.P65Warnings.ca.gov

WARNING

When installed in a sleeping room it is recommended that

a smoke and/or CO alarm be installed in the bedroom. The

size of the room must be at least 50ft³ per 1,000 Btu/hr

stove input, if the stove exceeds the room size, outside air

must be installed.

NOTE: Hearth & Home Technologies, manufacturer

of this appliance, reserves the right to alter

its products, their specications and/or price

without notice.

E. Mobile Home Approved

• This appliance is approved for mobile home

installations when not installed in a sleeping room and

when an outside combustion air inlet is provided.

• The structural integrity of the mobile home oor, ceiling,

and walls must be maintained.

• The appliance must be properly grounded to the frame

of the mobile home with #8 copper ground wire, and

chimney must be listed to UL103 HT or a listed UL-

1777 full length six inch (152mm) diameter liner must

be used.

• Outside Air Kit, part OAK-ACC must be installed in a

mobile home installation.

Improper installation, adjustment, alteration, service or

maintenance can cause injury or property damage.

For assistance or additional information, consult a qualied

installer, service agency or your dealer.

D. Glass Specications

This appliance is equipped with 5mm ceramic glass.

Replace glass only with 5mm ceramic glass. Please

contact your dealer for replacement glass.

WARNING

Fire Risk.

Hearth & Home Technologies disclaims any

responsibility for, and the warranty will be

voided by, the following actions:

• Installation and use of any damaged appliance.

• Modication of the appliance.

• Installation other than as instructed by Hearth &

Home Technologies.

• Installation and/or use of any component part not

approved by Hearth & Home Technologies.

• Operating appliance without fully assembling

all components.

• Operating appliance without legs attached (if

supplied with appliance).

• Do NOT Over re - If appliance or chimney

connector glows, you are over ring.

Any such action that may cause a re hazard.

902/237039-802G

A. Over-Firing Your Appliance

B. Wood Selection & Storage

Burn only dry seasoned wood. Store wood under cover,

out of the rain and snow. Dry and well-seasoned wood will

not only minimize the chance of creosote formation, but will

give you the most ecient re. Even dry wood contains at

least 15% moisture by weight, and should be burned hot

enough to keep the chimney hot for as long as it takes to

dry the wood out - about one hour. It is a waste of energy to

burn unseasoned wood of any kind.

Dead wood lying on the forest oor should be considered

wet, and requires full seasoning time. Standing dead wood

can be considered to be about 2/3 seasoned. To tell if wood

is dry enough to burn, check the ends of the logs. If there

are cracks radiating in all directions from the center, it is dry.

If your wood sizzles in the re, even though the surface is

dry, it may not be fully cured.

Visit www.quadrare.com/shopping-tools/videos to view

product and use & care videos.

1. Symptoms of Over-Firing

Symptoms of over-ring may include one or more of

the following:

- Chimney connector or appliance glowing

- Roaring, rumbling noises

- Loud cracking or banging sounds

- Metal warping

- Chimney re

2. What To Do if Your Appliance is Over-Firing

- Immediately close the door and air controls to reduce

air supply to the re.

- If you suspect a chimney re, call the re department

and evacuate your house.

- Contact your local chimney professional and have

your appliance and appliance pipe inspected for

any damage.

- Do not use your appliance until the chimney

professional informs you it is safe to do so.

Hearth & Home Technologies WILL NOT warranty

appliances that exhibit evidence of over-ring. Evidence

of over-ring includes, but is not limited to:

• Warped air tube

• Deteriorated refractory brick retainers

• Deteriorated bae and other interior components

2 2 Operating Instructions

Fire Risk. Do not over-re.

Over-ring may ignite creosote or will damage

the appliance and chimney.

To prevent over-ring your appliance,

DO NOT:

• Use ammable liquids

• Overload with wood

• Burn trash or large amounts of scrap lumber

• Permit too much air to the re

WARNING

Splitting wood before it is stored reduces drying time.

Wood should be stacked so that both ends of each piece

are exposed to air, since more drying occurs through the

cut ends than the sides. This is true even with wood that

has been split. Store wood under cover, such as in a shed,

or covered with a tarp, plastic, tar paper, sheets of scrap

plywood, etc., as uncovered wood can absorb water from

rain or snow, delaying the seasoning process.

C. Burning Process

In recent years there has been an increasing concern

about air quality. Much of the blame for poor air quality

has been placed on the burning of wood for home heating.

In order to improve the situation, we at Quadra-Fire

have developed cleaner-burning wood appliances that

surpass the requirements for emissions established by our

governing agencies. These wood appliances, like any other

appliances, must be properly operated in order to insure

that they perform the way they are designed to perform.

Improper operation can turn most any wood appliance into

a smoldering environmental hazard.

1. Kindling or First Stage: It helps to know a little about

the actual process of burning in order to understand

what goes on inside a appliance. The rst stage of

burning is called the kindling stage. In this stage,

the wood is heated to a temperature high enough to

evaporate the moisture which is present in all wood.

The wood will reach the boiling point of water (212°F)

and will not get any hotter until the water is evaporated.

This process takes heat from the coals and tends to

cool the appliance.

Fire requires three things to burn - fuel, air and heat. So,

if heat is robbed from the appliance during the drying

stage, the new load of wood has reduced the chances

for a good clean burn. For this reason, it is always best

to burn dry, seasoned rewood. When the wood isn’t

dry, you must open the air controls and burn at a high

burn setting for a longer time to start it burning. The

heat generated from the re should be warming your

home and establishing the ue draft, not evaporating

the moisture out of wet, unseasoned wood, resulting in

wasted heat.

2. Second Stage: The next stage of burning, the

secondary stage, is the period when the wood gives o

ammable gases which burn above the fuel with bright

ames. During this stage of burning it is very important

that the ames be maintained and not allowed to go

out. This will ensure the cleanest possible re. If the

ames tend to go out, it is set too low for your burning

conditions. The air control located at the upper right

hand corner is used to adjust for burn rates. This is

called the Burn Rate Air Control (Figure 10.1).

3. Final Stage: The nal stage of burning is the charcoal

stage. This occurs when the ammable gases have

been mostly burned and only charcoal remains. This

is a naturally clean portion of the burn. The coals burn

with hot blue ames.

10 02/237039-802G

Figure 10.1

HIGH

MED

LOW

Burn Rate

Air Control

Start-Up

Air Control

It is very important to reload your appliance while

enough lively hot coals remain in order to provide the

amount of heat needed to dry and rekindle the next load

of wood. It is best to open the Burn Rate Air and Start-

Up Air Controls before reloading. This livens up the coal

bed and reduces excessive emissions (opacity/smoke).

Open door slowly so that ash or smoke does not exit

appliance through opening. You should also break up

any large chunks and distribute the coals so that the

new wood is laid on hot coals.

Air quality is important to all of us, and if we choose to use

wood to heat our homes we should do so responsibly.

To do this we need to learn to burn our appliances in

the cleanest way possible. Doing this will allow us to

continue using our wood appliances for many years to

come.

2. Medium low burn setting:

- Burn Rate Air Control spring handle up to high position

for 5 minutes.

- Then activate the ACC timer system by pushing the

knob all the way back toward the appliance to “HI”

then pull forwards towards the front of the appliance

until the knob stops.

- At that point move the Burn Rate Air Control spring

handle to 1/8”-1/2” from the low setting.

3. Medium high burn setting:

- Burn Rate Air Control spring handle up to high position.

- Then activate the ACC timer system by pushing the

knob all the way back toward the appliance to “HI”

then pull forwards towards the front of the appliance

until the knob stops.

- At that point move the Burn Rate Air Control spring

handle to 1/2” – high.

4. High burn setting:

- Burn Rate Air Control spring handle up to high position

- Also activate ACC timer system knob pushed back to

the “HI” position.

Surface Thermometer is a Valuable Guide to Operation

A surface thermometer tells you when to adjust the air

control, and when to refuel, Figure 10.1.

For example, when the thermometer registers at least 450°F

(230°C) on the stove top after start-up you know the stove

is hot enough and it may be time to adjust the air control

if a sucient ember bed has also been established. Note

that the stove will warm up much sooner than the chimney,

though; a warm chimney is the key to easy, eective stove

operation. When thermometer readings drop below 350°F.

(175°C) it’s time to adjust the air control for a higher burn

rate or to reload the stove. A temperature reading over

650°F. (340°C) is a sign to reduce the air supply to slow the

burn rate.

Use the following temperature ranges as a guide:

• Readings in the 350°-500°F. (175°-260°C) range indicate

low to medium heat output.

• 500°-600°F. (260°-315°C) readings indicate medium

heat output.

• Readings of 600°-650°F. (315-340°C) indicate high

heat output. Operating your wood stove continuously at

stove top temperatures higher than 650° F (340°C) may

damage your wood stove.

NOTE: The above information is provided as a guideline

only. Altitude and other circumstances may require

control adjustments to achieve the desired burn rates.

NOTE: Operate appliance on High Burn 45 minutes a

day to help keep ue/chimney clean.

NOTE: If using the optional blower, for burn rate settings

1-3, the blower shall be o for the rst 30 minutes and

then be operated in the high position at 30 minutes. For

high burn setting, blower may continue to be on full after

the loading of the fuel.

D. Burn Rates and Operating Eciency

For maximum operating eciency

This wood appliance has a manufacturer-set minimum

low burn rate that must not be altered. It is against federal

regulations to alter this setting or otherwise operate this

wood appliance in a manner inconsistent with operating

instructions in this manual.

• Burn dry, well-seasoned wood.

Burn Rates

1. Low burn setting:

- Burn Rate Air Control spring handle up to high position

for 5 minutes.

- Then activate the ACC timer system by pushing the

knob all the way back toward the appliance to “HI”

then pull forwards towards the front of the appliance

until the knob stops (Figure 10.1).

- At that point close the Burn Rate Air Control by moving

the spring handle to the low setting.

Surface

Thermometer



11 02/237039-802G

Figure 11.1

High (Open)

Low (Closed)

Burn Rate

Air Control

Start-Up Air

Control

LOW

Timer

Timer Manual

Rear Air Channel

Operates independently

from Timer Shut-off

Shown with Side

Shield Removed

Front Air Channel

Operated by Timer

HIGH

After activating the timer (ACC), if the control is placed

within the rear air section on the label it will allow rear air

to enter the rebox. This will not interfere with the timer

gradually closing the front air channel in 25 minutes. If

control is set on “HI” it over-rides the timer (ACC).

Risk of Fire.

When set on High Burn Rate and over-riding

the Automatic Combustion Control system an

over re situation can occur and may result in

a chimney re.

Over ring will void the appliance warranty.

WARNING

Injury Risk.

• Gloves recommended

CAUTION

Figure 11.2

HIGH

MED

LOW

Burn Rate

Air Control

Start-Up

Air Control

Figure 11.3

Manual

Timer (ACC)

Shut Down

Pull Forward

to Shut Down

Manual Timer Over-Ride: If you need to shut the ACC

system o before it goes through the cycle of shutting itself

o; 25 minutes, reach towards the back of the appliance

on the right side and pull the lever towards the front of the

appliance (Figure 11.3).

Figure 11.4

Over rides timer & opens

rear air to open locked

position

Open rear air medium air

flow

Engages timer push knob

towards HI then back to

any point within dotted line

Open rear air medium-low

air flow

Closes front and rear air

12 02/237039-802G

Baffle Board even with front tube & resting

on all tubes

Burn Rate

Air Control

Start-Up Air

Control

Figure 12.1

E. Building A Fire

Before lighting your rst re in the appliance:

NOTE: The special high temperature paint that your

appliance is nished with will cure as your appliance

heats. You will notice an odor and perhaps see some

vapor rise from the appliance surface; this is normal.

We recommend that you open a window until the odor

dissipates and paint is cured.

Tube Channels

Ceramic Blanket on Top

2 pc Baffle Board

Figure 12.2

NOTE:

• Build re on brick rebox oor.

• Do NOT use grates, andirons or other methods to

support fuel. It will adversely aect emissions.

1. Conrm the bae is correctly positioned. It should be

even with the front tube and resting on all tubes (Figure

12.1 and Figure 12.2).

2. Remove all labels from glass and inside of appliance.

There are many ways to build a re. The basic principle

is to light easily-ignitable tinder or paper, which ignites the

fast burning kindling, which in turn ignites the slow-burning

rewood. Here is one method that works well:

1. Open the Burn Rate Air and ACC Controls fully (Refer to

the Quick Start Guide on page 6).

2. Place several wads of crushed paper on the rebox oor.

Heating the ue with slightly crumpled newspaper before

adding kindling keeps smoke to a minimum.

3. Lay small dry sticks of kindling on top of the paper.

4. Make sure that no matches or other combustibles are in

the immediate area of the appliance. Be sure the room is

adequately ventilated and the ue unobstructed.

5. Light the paper in the appliance. NEVER light or rekindle

re with kerosene, gasoline, or charcoal lighter uid; the

results can be fatal.

6. Once the kindling is burning quickly, add several full-

length logs 3 inches (76mm) or 4 inches (102mm) in

diameter. Be careful not to smother the re. Stack the

pieces of wood carefully; near enough to keep each

other hot, but far enough away from each other to allow

adequate air ow between them.

7. Set the Burn Rate Air Control and activate the ACC timer

system.

8. When ready to reload, It is best to fully open both the Burn

Rate Air and Start-up Air Controls before reloading. This

livens up the coal bed and reduces excessive emissions

(opacity/smoke). Open door slowly so that ash or smoke

does not exit appliance through opening. Large logs

burn slowly, holding a re longer. Small logs burn fast

and hot, giving quick heat.

9. As long as there are hot coals, repeating steps 6 through

8 will maintain a continuous re.

Fire Risk.

• Do not leave the re unattended when

the door is unlatched or when using the

re screen.

• Unstable rewood could fall out of the

rebox creating a re hazard to your home.

WARNING

Fire Risk.

Do NOT store wood:

• Closer than required clearances to

combustibles to appliance

• Within space required for loading or

ash removal.

Do NOT operate appliance:

• With appliance door open.

• With ash removal system door open.

WARNING

Fire Risk.

• Do NOT burn wet or green wood.

• Store wood in dry location.

• Stack wood so both ends are exposed

to air.

Wet, unseasoned wood can cause

accumulation of creosote.

WARNING

13 02/237039-802G

F. Blower Operating Instructions G. Opacity (Smoke)

This is the measure of how cleanly your appliance is burning.

Opacity is measured in percent; 100% opacity is when an

object is totally obscured by the smoke column from a

chimney, and 0% opacity means that no smoke column can

be seen. As you become familiar with your appliance, you

should periodically check the opacity. This will allow you to

know how to burn as nearly smoke-free as possible (goal of

0% opacity).

Figure 13.2

MANUAL

FAN

AUTO

LOW

HIGH OFF

MANUAL:

Over-rides

the Snap

Disc

AUTO: Fan

will turn

ON/OFF

Automatically

by the Snap

Disc

Controls

the Fan

Speed

NOTE: If your Quadra-Fire wood appliance is equipped

with an optional blower, you should follow these

guidelines:

1. Initial (cold) start-up and all Burn Settings: The

blower can be plugged in and turned on right away. The

blower fan is turned on and o by a snap disc. When your

appliance has reached a certain temperature the blower

will turn on and when your appliance has cooled down

to a certain temperature it will turn o. Switch on blower

control must be set to auto for this feature to work.

2. The blower is equipped with a speed control. Adjust

the fan speed by turning the speed control clockwise to

“Low” or counterclockwise to “High”.

3. Snap Disc Location: If you nd the blower coming on

and o at undesirable temperatures, relocate the snap

disc to another location in the designated zone on the

back of the appliance (Figure 13.1). There is a manual

over-ride switch to deactivate the snap disc, if necessary

(Figure 13.2).

Fire Risk.

• DO NOT BURN GARBAGE OR

FLAMMABLE FLUIDS SUCH AS

GASOLINE, NAPHTHA OR ENGINE OIL.

• Do NOT burn treated wood or wood with

salt (driftwood).

• May generate carbon monoxide if burn

material other than wood.

May result in illness or possible death.

WARNING

When burning your rst re, you will experience

smoke and odor from the appliance resulting from the

curing of paint and burning o of any oils remaining

from manufacturing.

OPEN WINDOWS DURING INITIAL BURN TO

DISSIPATE SMOKE AND ODORS!

• Odors may be irritating to sensitive individuals.

• Smoke detectors may activate.

CAUTION

WARNING

Fire Risk.

Keep combustible materials, gasoline and

other ammable vapors and liquids clear

of appliance.

• Do NOT store ammable materials in the

appliance’s vicinity.

• DO NOT USE GASOLINE, LANTERN FUEL,

KEROSENE, CHARCOAL LIGHTER FLUID OR

SIMILAR LIQUIDS TO START OR “FRESHEN UP” A

FIRE IN THIS Appliance.

• Keep all such liquids well away from the appliance

while it is in use.

• Combustible materials may ignite.

Figure 13.1

Snap Disc LacationSnap Disc Lacation

14 02/237039-802G

Negative pressure results from the imbalance of air available

for the appliance to operate properly. It can be strongest in

lower levels of the house.

Causes include:

• Exhaust fans (kitchen, bath, etc.)

• Range hoods

• Combustion air requirements for furnaces, water

appliances and other combustion appliances

• Clothes dryers

• Location of return-air vents to furnace or air conditioning

• Imbalances of the HVAC air handling system

• Upper level air leaks such as:

- Recessed lighting

- Attic hatch

- Duct leaks

To minimize the eects of negative air pressure:

• Install the outside air kit with the intake facing prevailing

winds during the heating season

• Ensure adequate outdoor air for all combustion

appliances and exhaust equipment

• Ensure furnace and air conditioning return vents are not

located in the immediate vicinity of the appliance

• Avoid installing the appliance near doors, walkways or

small isolated spaces

• Recessed lighting should be a “sealed can” design

• Attic hatches weather stripped or sealed

• Attic mounted duct work and air handler joints and seams

taped or sealed

I. Negative PressureH. Clear Space

Figure 14.1

Maintain 4 ft (1.22m) clearance to

combustibles in front of appliance

NOTE: Do NOT place combustible objects within

4 ft (1.2m) of the front of appliance (Figure 14.1).

• Mantel: Avoid placing candles and other heat-sensitive

objects on mantel or hearth. Heat may damage these

objects.

Do NOT place combustible objects in front of the

appliance. High temperatures may ignite clothing,

furniture or draperies.

WARNING

Asphyxiation Risk.

• Negative pressure can cause spillage

of combustion fumes, soot and

carbon monoxide.

• Appliance needs to draft properly for safety.

WARNING

15 02/237039-802G

J. Frequently Asked Questions

ISSUES SOLUTIONS

Odor from appliance When rst operated, this appliance may release an odor for the rst several hours. This is

caused by the curing of the paint and the burning o of any oils remaining from manufacturing.

Metallic noise

Noise is caused by metal expanding and contracting as it heats up and cools down, similar to

the sound produced by a furnace or heating duct. This noise does not aect the operation or

longevity of the appliance.

Whirring sound If the optional blower has been installed, the blower produces a whirring sound which

increases in volume as the speed is increased.

CONTACT YOUR DEALER for additional information regarding operation and troubleshooting.

Visit www.quadrare.com to nd a dealer.

Table 15.1

Fire Risk.

• DO NOT BURN GARBAGE OR

FLAMMABLE FLUIDS SUCH AS

GASOLINE, NAPHTHA OR ENGINE OIL.

• Do NOT burn treated wood or wood with

salt (driftwood).

• May generate carbon monoxide if burn

material other than wood.

May result in illness or possible death.

WARNING WARNING

Fire Risk.

Keep combustible materials, gasoline and

other ammable vapors and liquids clear

of appliance.

• Do NOT store ammable materials in the

appliance’s vicinity.

• DO NOT USE GASOLINE, LANTERN FUEL,

KEROSENE, CHARCOAL LIGHTER FLUID OR

SIMILAR LIQUIDS TO START OR “FRESHEN UP” A

FIRE IN THIS APPLIANCE.

• Keep all such liquids well away from the appliance

while it is in use.

• Combustible materials may ignite.

16 02/237039-802G

A. Quick Reference Maintenance Guide

When properly maintained, your replace will give

you many years of trouble-free service. Contact your

dealer to answer questions regarding proper operation,

troubleshooting and service for your appliance. Visit

www.quadrare.com/owner-resources to view basic

troubleshooting, FAQs, use & care videos.

3 Maintenance and Service

CAUTION

Allow the appliance to completely cool down before

performing any cleaning or maintenance. Start the

rst inspection after the rst 2 months of use, or if

performance changes, and adjust your schedule

accordingly. Maintenance is required for safe operation

and must be performed to maintain your warranty.

FREQUENCY TASK

Ba e & Blanket

MONTHLY

or after every

one (1) cord of

wood

Ba e and blanket placement is critical to heat output, e ciency and

overall life of the appliance. Make sure the ba e is pushed all of the

way to the back of the  rebox and the blanket is laying  at. Inspect

ba e for cracks.

Ceramic Blanket Back of Firebox

Baffle Board

Baffle Retainer

Bracket

Optional Blower

YEARLY or after

every four (4)

cords of wood Vacuum the blower impellers.

Chimney System

EVERY TWO

MONTHS

or after every

four (4) cords of

wood

The chimney and chimney cap must be inspected for soot and

creosote every two months during the burn season or more frequency

if chimney exceeds or is under 14-16 ft (4.3m-4.8m) measured from

bottom of appliance.

This will prevent pipe blockage, poor draft, and chimney  res.

Always burn dry wood to help prevent cap blockage and creosote

build-up.

Firebrick & Ash Removal

WEEKLY

or after every 25

loads of wood

Ashes must be cool before you can dispose of the ashes in a non-

combustible container.

Firebrick is designed to protect your  rebox. After ashes are removed,

inspect the  rebrick and replace  rebricks that are crumbling, cracked

or broken.

Door & Glass Assemblies

WEEKLY

or after every 25

loads of wood

Keep door and glass gasket in good shape to maintain good burn.

To test: place a dollar bill between the appliance and door and then

shut the door. If you can pull the dollar out, remove one washer from

door handle behind latch cam and try again. If you can still pull it out,

replace the door gasket.

Check the glass frame for loose screws to prevent air leakage.

Check glass for cracks.

Door Handles

WEEKLY

or after every 25

loads of wood

Check the door latch for proper adjustment. This is very important

especially after the door rope has formed to the appliance face.

Check door handle for smooth cam operation.

These are generic drawings and may not represent your model.

Table 16.1

17 02/237039-802G

B. General Maintenance

1. Creosote (Chimney) Cleaning

• Frequency: Every 2 months during heating season or

as recommended by a certied chimney sweep; more

frequently if chimney exceeds or is under 14-16 ft.

(measured from bottom of appliance)

• By: Certied Chimney Sweep

Remove all ash from the rebox and extinguish all hot

embers before disposal. Allow the appliance to cool

completely. Disconnect ue pipe or remove bae and

ceramic blanket from appliance before cleaning chimney.

Otherwise residue can pile up on top of the bae and

ceramic blanket and the appliance will not work properly.

(See Bae Removal on page 23). Close the door tightly.

The creosote or soot should be removed with a brush

specically designed for the type of chimney in use. Clean

out fallen ashes from the rebox.

It is also recommended that before each heating season

the entire system be professionally inspected, cleaned and

repaired if necessary.

Inspection:

Inspect the system at the appliance connection and at

the chimney top. Cooler surfaces tend to build creosote

deposits quicker, so it is important to check the

chimney from the top as well as from the bottom.

Formation and Need For Removal:

When wood is burned slowly, it produces tar and other

organic vapors which combine with expelled moisture

to form creosote.

The creosote vapors condense in the relatively cool

chimney ue of a newly-started or a slow-burning re. As

a result, creosote residue accumulates on the ue lining.

When ignited, this creosote creates an extremely hot re

which may damage the chimney or even destroy the house.

The chimney connector and chimney should be inspected

once every 2 months during the heating season to

determine if a creosote or soot buildup has occurred. If

creosote or soot has accumulated, it should be removed to

reduce the risk of a chimney re.

2. Disposal of Ashes

• Frequency:

When ash is within 1-3/4 in. (44mm) of

rebox lip

• By: Homeowner

WARNING

Fire Risk.

Prevent creosote buildup.

• Inspect chimney connector and

chimney once every two months during

heating season.

• Remove creosote to reduce risk of

chimney re.

• Ignited creosote is extremely HOT.

Fire Risk.

• Do not use chimney cleaners or ame

colorants in your appliance. Will corrode

chimney pipe.

WARNING

Fire Risk. Disposal of Ashes

• Ashes should be placed in metal container

with tight tting lid.

• Do not place metal container on

combustible surface.

• Ashes should be retained in closed

container until all cinders have

thoroughly cooled.

WARNING

Ashes should be placed in a metal container with a tight

tting lid. The closed container of ashes should be placed

on a non-combustible oor or on the ground, well away

from all combustible materials, pending nal disposal. If the

ashes are disposed of by burial in soil or otherwise locally

dispersed, they should be retained in the closed container

until all cinders have thoroughly cooled.

Fire Risk.

Ashes could contain hot embers.

WARNING

3. Appliance Inspection

• Frequency: Every 2 months at the same time the

chimney and chimney connector are inspected.

• By: Homeowner

Check for:

• Cracks in glass

• Door handle - smooth cam operation

• Bae and ceramic blanket correct placement

• Bae for warp-age

• Firebrick for cracks, broken or crumbly

• Door gasket (Dollar bill test): Place a dollar bill between

the stove and the door and then shut the door. If you

can pull the dollar bill out, replace the door gasket.

• Glass frame for loose screws

18 02/237039-802G

4. Glass Cleaning

• Frequency: As desired

• By: Homeowner

CAUTION

• Do not use polishes with abrasives. It will scratch

plated surfaces.

CAUTION

• Do not use polishes with abrasives. It will

scratch surfaces.

5. Cleaning Plated Surfaces

• Frequency: Prior to first burn and then as desired

• By: Homeowner

Clean all the ngerprints and oils from plated surfaces

BEFORE ring the appliance for the rst time. If not

cleaned properly before lighting your rst re, the oils can

cause permanent markings on the plating.

After the plating is cured, the oils will not aect the nish

and little maintenance is required. Wipe clean as needed.

Clean glass with a non-abrasive glass cleaner. Abrasive

cleaners may scratch and cause glass to crack. If the

deposits on the glass are not very heavy, normal glass

cleaners work well. Heavier deposits may be removed by

using a damp cloth dipped in wood ashes or by using a

commercially available oven cleaner.

After using an oven cleaner, it is advisable to remove any

residue with a glass cleaner or soap and water. Oven

cleaner left on during the next ring can permanently stain

the glass and damage the nish on metal surfaces.

A portion of the combustion air entering the rebox is

deected down over the inside of the door glass. This

air ow “washes” the glass, helping to keep smoke from

adhering to its surface.

When operated at a low burn rate, less air will be owing

over the glass and the smokey, relatively cool condition of a

low re will cause the glass to become coated.

Operating the appliance with the Burn Rate Air Control and

Start-Up Air Control all the way open for 30-45 minutes

should remove the built up coating.

CAUTION

Handle glass assembly with care. Glass is breakable.

• Avoid striking, scratching or slamming glass

• Avoid abrasive cleaners

• Do not clean glass while it is hot

6. Inspect Firebrick

• Frequency: After each ash removal

• By: Homeowner

Replace the rebrick if they become crumbly and/or if there

is a 1/4 inch (6.35mm) gap between the bricks.

The rebox is lined with rebrick, which has exceptional

insulating properties. Do not use a grate; simply build

a re on the rebox oor. Do not operate appliance

without rebrick.

1. After the coals have completely cooled, remove all old

brick and ash from unit and vacuum rebox.

2. Remove new brick set from box and lay out to the

diagram shown in the instructions that come with the

brick set or refer to the diagram on the service parts list

at the end of this manual.

3. Lay bottom bricks in unit.

4. Install rear bricks on the top of the bottom bricks. Slide

top of bricks under clip on back of rebox wall and push

bottom of bricks back.

5. Install side bricks. Slide top of brick under clips on side

of rebox and push the bottom of the brick until it is

ush with the side of the unit.

19 02/237039-802G

INCORRECT POSITIONS

C. Correct Bae & Blanket Placement

Ceramic Blanket and Bae Board are NOT in contact

with the back of the rebox.

Ceramic Blanket is NOT in contact with the back of the

rebox and NOT even with the Bae Board in the front.

Ceramic Blanket is bunched up at the back of the rebox

and NOT even with the Bae Board in the front.

Ceramic Blanket

Back of

Firebox

Baffle Board

Figure 19.2

Figure 19.1

CORRECT POSITION

Ceramic Blanket and Bae Board MUST be in contact

with the back of the rebox and even with each other in

the front.

Ceramic Blanket Back of Firebox

Baffle Board

Baffle Retainer

Bracket

WARNING

Fire Risk.

Firebox damage due to improper bae

placement is not covered by warranty.

Operate the wood burning appliance with the

bae in the correct position only.

Not doing so could result in:

• Reduced eciency

• Overheating the chimney

• Overheating the rear of the rebox

• Poor performance

Ensure correct bae placement and replace

bae components if damaged or missing.

The bae boards are FRAGILE. Use extreme caution

when loading rewood to prevent:

• Cracking, breaking or damaging the bae boards

DO NOT operate the appliance without bae boards

CAUTION

20 02/237039-802G

With proper installation, operation, and maintenance your wood appliance will provide years of trouble-free service. If

you do experience a problem, this troubleshooting guide will assist you or a qualied service person in the diagnosis of a

problem and the corrective action to be taken.

START FIRE PROBLEMS POSSIBLE CAUSE SOLUTION

Can not get re started

Excessive smoke or spillage

Burns too slowly Not enough

heat output

Not enough kindling/paper or no

kindling/paper

Use dry kindling, more paper. Arrange kindling &

wood for air movement.

Not enough air for re to ignite

Check for restricted termination cap

Check for blockage of outside air kit (if installed).

Check for ue blockage.

Pre-warm ue before starting re (refer to

Building a Fire on page 13).

Check for adequate vent height (refer to Chimney

Height / Rise and Run on page 13 of the

Installation manual).

Open window below the appliance towards

the wind.

Wood condition is too wet,

too large

Use dry, seasoned wood (refer to Wood Selection

& Storage on page 9).

Bed of coals not established before

adding wood

Start with paper & kindling to establish bed of

coals (refer to Building a Fire on page 13).

Flue blockage such as birds’ nests

or leaves in termination cap Have chimney inspected for creosote and cleaned

by a certied chimney sweep.

Down draft or negative pressure

Competition with exhaust devices

Do not use exhaust fans during start-up (refer to

Negative Pressure on page 15).

Open window below the appliance towards

the wind.

Fire burns too fast

Extremely dry or soft wood

Mix in hardwood.

Mix in less seasoned wood after re is established

(refer to Wood Selection & Storage on page 9).

Over drafting

Check for correct vent height; too much vertical

height creates over drafting.

Check location of vent termination (refer to

Chimney Termination Requirement on page 12

of the Installation manual).

4 Troubleshooting Guide

Table 20.1

La page charge ...

Quadra-Fire 2100 Millennium Wood Stove Le manuel du propriétaire

Marque: Quadra-Fire

Modèle: 2100 Millennium Wood Stove

Catégorie: Cheminées

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Quadra-Fire 2100 Millennium Wood Stove Owner's manual

Documents connexes

Quadra-Fire Discovery I Wood Stove Le manuel du propriétaire

Quadra-Fire 2100 Millennium Wood Stove Le manuel du propriétaire

Quadra-Fire 2100 Millennium Wood Stove Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents